MODEL 1433FH Fixed Head Power Meat Saw Operating and Service Manual
MODEL 1433FH Fixed Head Power Meat Saw Operating and Service Manual
MODEL 1433FH Fixed Head Power Meat Saw Operating and Service Manual
FIXED HEAD
POWER MEAT SAW
OPERATING AND SERVICE MANUAL
IMPORTANT NOTICE
This Manual contains important
safety instructions which must
be strictly followed when using
this equipment. ITEM No. 14313FH-304
MD 1433FH 5-18-13 B
TABLE OF CONTENTS
Page
NOTICE TO OWNERS AND OPERATORS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SAFETY TIPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
LUBRICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
OPERATOR’S NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
OPERATOR’S NOTES . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
CLEANING PROCEDURE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
LIMITED WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
NOTICE TO OWNERS AND OPERATORS
BIRO’s products are designed to process food products safely and efficiently. Unless the operator is
properly trained and supervised, there is the possibility of a serious injury. It is the responsibility of the owner
to assure that this machine is used properly and safely, strictly following the instructions contained in this
Manual and any requirements of local law.
No one should use or service this machine without proper training and supervision. All operators should
be thoroughly familiar with the procedures contained in this Manual. Even so BIRO cannot anticipate every
circumstance or environment in which its products will be used. You, the owner and operator, must remain alert
to the hazards posed by the function of this equipment, particularly the SHARP MOVING BAND TYPE SAW
BLADE. No one under eighteen (18) years of age should operate this equipment. If you are uncertain about a
particular task, ask your supervisor.
This Manual contains a number of safe practices in the SAFETY TIP section. Additional warnings are
placed throughout the Manual. Warnings related to your personal safety are indicated by:
OR
BIRO also has provided a wall chart to be posted near the equipment. If any warning label, wall chart, or
Manual becomes misplaced, damaged, or illegible, please contact your nearest Distributor or Biro directly for a
replacement.
Remember, however, this Manual or the warning labels do not replace the need to be alert and to use
your common sense when using this equipment.
This Manual applies to 1433FH Power Meat Saws with Fixed Heads.
- NOTE -
A copy of this manual is included with each Model 1433FH saw.
The descriptions and illustrations contained in this manual are not binding.
The manufacturer reserves the right to introduce any modification without
updating the manual.
1
SAFETY TIPS
2
INSTALLATION
3. After installing machine in operational area, it is imperative that the four adjusting leg hex bolts be adjusted to level the
machine and also to eliminate rocking.
4. To assemble meat gauge plate (Part No. A14275) to the machine; Loosen the lock knob (Part No. 272-10) on the right side meat
gauge bracket. Remove the meat gauge gear rack (Part No. S14272) and insert into the meat gauge plate. Be sure to hold meat
gauge arm so that the release handle is depressed. Re-install the gear rack by first inserting the rectangle end into the left hand
meat gauge bracket, then swing the right hollow round end of the gear into the original lock position. Upon aligning the gear
rack with the capscrew (Part No. 272-11), tighten the lock knob clockwise, fastening the locking cap screw into the hollow end
to the gear rack, CHECKING for a secure assembly. Keep gear rack well oiled with food grade oil to ensure free movement.
3
5. Place removable finger lift with saw guard assembly
(Part No. A14211) on the saw guide bar (Part No. S116-22)
and fasten in place with finger lift fastener knob
(Part No. 211A-291Q). FINGERLIFT
ASSEMBLY
6. See Lower Removable Wheel Installation and Removal
Instructions for Model 1433 below.
REMOVAL and INSTALLATION
for Self-Centering Lower Removable Wheels
(Part No. 14560-1 and 14560DF-1)
ALWAYS Turn off, unplug Machine From Power Source and Perform Lockout/Tagout Procedure
to the Machine BEFORE Cleaning or Servicing.
Follow disassembly procedures in the Cleaning Section of the Operating and Service Manual.
Removal of the T-Handle and Lower Wheel will be the last 2 parts removed in the number sequence.
REMOVAL
Loosen Item No. 14746-1, T-Handle and Remove from Lower Shaft.
INSTALLATION
There is an anti-rotation pin located on the lower shaft,
there is an anti-rotation groove located on the back side
of the lower wheel.
Align and engage the groove of the lower wheel and the
anti-rotation pin as the wheel is being installed. Install T-Handle Lock onto Lower
Shaft, Hand Tighten SECURELY
4
REMOVAL and INSTALLATION INSTRUCTIONS
for TAPERED BORE LOWER WHEELS
14560 and 14560DF
ALWAYS Turn off, unplug Machine From Power Source and Perform Lockout/Tagout Procedure
to the Machine BEFORE Cleaning or Servicing.
Follow Disassembly Procedures in the Cleaning Section of the Operating and Service Manual.
Removal of the Lower Wheel will be the last procedure.
REMOVAL
Loosen the Item No. 14746 T-Handle lock, DO NOT REMOVE COMPLETELY FROM SHAFT.
14746
T-Handle
T-Handle
Loosened
Lock
14746
T-Handle
Using thumbs for leverage, pull wheel toward you with Lock
an even-smooth motion. Wheel is mounted in slip fit
fashion on a tapered shaft. When the wheel is loose,
complete removing T-handle lock and wheel.
INSTALLATION
NOTE:
TO ENSURE PROPER SAW
WHEEL ALIGNMENT, WHEEL Replace the T-Handle Lock
MUST BE REINSTALLED HAND TIGHTEN ONLY
ON SAME MACHINE FROM Reassemble the machine.
WHICH IT WAS REMOVED.
5
Item No. 16543 - Lower Shaft for Removable Wheel
7. The Model 1433 Lower Removable Wheel has been revised to include a keyway in the bore. Also an anti rotation pin
is now pressed into the lower shaft to prevent any inadvertent “spinning” of the wheel on the shaft.
NOTE- If the saw in which a new shaft is to be PRESS IN PIN HERE
installed has a groove (keyway) in the bore of the TAPER PIN 3/32
LOWER BEARING SHAFT,
REMOVABLE SAW WHEEL
lower wheel, press the taper pin (provided “loose”) ITEM NO. S235 ITEM NO. 16543
9. All machines are tested at the factory, but electrical phasing for proper rotation may not match your electrical
supply. All machines with removable lower wheel must be first test run for proper phasing with the lower wheel
removed. Failure to remove the lower wheel could cause the wheel to become dislodged during testing.
All machines with removable lower wheel will display the following decal on the right hinged base door.
6
SHARP SAW BLADE. HANDLE WITH EXTREME CAUTION.
10. Placing blade on cutter: Unpack upper wheel assembly and hang on the hinge bracket in the head structure. Lift
the nylon filler in the stationary bar. Hang blade on the upper wheel and hold with right hand. With the left hand
force the back of the blade between the front blade scrapers, located below the stationary bar. Lower the nylon
filler. Be sure the blade is in the upper saw guide. The blade has dropped over the lower wheel. Switch hands
holding the blade on the upper wheel. With the right hand, force the back of the blade between the rear blade
scrapers. The blade is now ready to be tightened.
11. Turn the blade tensioning handle clockwise until the tension mark is even with the bottom of the upper wheel
hinge plate as shown. Carefully turn saw wheels by hand and watch for proper tracking of blade on the wheels.
12. The stationary platter is placed on top of the base structure and held in place by two push-pull hold down rods,
located at the rear of the base.
13. The sliding meat carriage assembly is installed by turning the movable stop assembly clockwise. After the carriage
assembly is in the channel for operation, turn the movable stop counterclockwise to lock.
14. Make sure saw guide bar with saw guard is in its lowest position. Close head and base doors.
15. Push the start button. Check for proper phasing of motor and proper tracking of the saw blade in the saw guides. Back
of the blade should be centered in the lower saw guide in the stationary bar. Blade should be moving down through
the guide. Push the stop button to stop the machine.
16. Check placement of all warning labels, wall chart and Manual. Machine is ready for trained operators to process
product. Post SAFETY TIPS wall chart within easy view of operator. Keep Manual available to operator.
17. Contact your local Distributor or BIRO directly if you have any questions or problems with the installation or
operation of this machine.
7
WARNING LABELS
FOR BIRO POWER MEAT SAWS
NOT TO SCALE
ITEM No. 708: ALL SAWS
Attached to saw Guard
on Saw Guide Bar
ITEM No. 16716: Item No.
Applied to Right Hinged Base 708
Door on All Model 1433FH
with Lower Removable Wheel.
Item No.
16716
8
WARNING LABEL LOCATIONS ON MACHINE
LOCATED INSIDE
HEADDOOR
ATTACH TO HINGED
RIGHT BASE DOOR
9
PART NUMBER 671
WALL CHART “BAND SAW SAFETY GUIDELINES”
ATTACH TO WALL IN VICINITY OF MACHINE IN EASY VIEW OF OPERATOR
10
OPERATION
2. ALWAYS clean and sanitize all utensils and surfaces that have been in contact with raw products.
11
B. TO PROCESS PRODUCT
1. Before starting power saw, adjust saw guide bar with saw guard to within 1/2” of product to be cut.
“B”
D
A
N
G
E
R
C
A
5. Stand in front of the power saw, place product on the meat carriage. Pay attention to position of your
hands. Keep hands clear of moving band type saw blade. Leaning lightly against the scalloped front edge
of meat carriage, hold the product firmly in right hand with product face flush against the meat gauge plate.
Move the meat carriage from right to left at a steady rate until fully past the saw blade. Use left hand to
remove and stack cut product, NEVER REACH IN FRONT OF BAND TYPE SAW BLADE. On the
return stroke, pull the product slightly toward you to clear the blade.
6. ALWAYS use the Safety End Cut Pusher Plate for smaller products or the last cuts of product. “C”
The pusher plate is supplied as standard on all BIRO power saws.
12
MAINTENANCE
e. STATIONARY BAR ASSEMBLY: Check condition of nylon filler (Part No. 177), change every four (4) weeks.
Check condition of saw guide (Part No. S119A), check tracking of blade through guide, back of blade should be
centered in hole, replace every six (6) months. Check condition of lower blade back-up guide (Part No. S608).
Check adjustment of back-up guide, should have 1/32” gap between back of blade and saw guide carbide.
Replace every six (6) months.
f. SAW CLEANERS: Check condition of blade cleaners, replace every four (4) weeks.
g. MEAT GAUGE ASSEMBLY: Check free movement of meat gauge plate on gear rack. Gear rack to be kept
lubricated at all times with light food grade oil. Check operation of release handle. Check that worm gear
engages properly with gear rack. Check tension of release handle spring, replace as necessary.
h. MEAT CARRIAGE ASSEMBLY: Check for free movement through full range of travel. Check for side to
side tolerance, adjust as necessary. Check condition and grease bearings, replace as necessary. Check condition
of thumb guard, replace as necessary.
i. SAFETY ITEMS: Safety end cut pusher plate is with machine and accessible. All warning labels are present,
properly affixed and legible. Model and Serial Number plate properly affixed and legible. Wall poster within
operator’s view from machine. Manual accessible to operator.
13
USE BIRO No. 374 GREASE FOR RE-GREASING
B. LUBRICATION:
SEE INSTRUCTIONS BELOW
1. UPPER WHEEL BEARINGS: Grease
every four (4) months. Change grease
every twelve (12) months.
2. LOWER BEARING HOUSING:
Grease every four (4) months. Change
grease every twelve (12) months.
3. MEAT CARRIAGE BEARINGS:
Grease every four (4) weeks.
4. SAW GUIDE BAR: Oil daily with food
machine oil.
5. MEAT GAUGE GEAR RACK: Oil
daily with food machine oil. When lubricating the upper wheel bearing it is important that
the three hex head screws securing the upper wheel hub cap
6. BLADE TENSION SPRING
be loosened slightly before attempting to pump grease into the
SCREW ASSEMBLY: Grease every
grease fitting. Loosening the screws allows for an escape of old
four (4) weeks. NOTE: Remove upper
broken down grease and air from the bearing cavity. Failure to
wheel and turn #14782 Blade Tension
loosen the screw before greasing the upper bearings can cause
screw clockwise until it bottoms out
the upper shaft seal to be dislodged from the upper wheel
against #14781 Blade Tension Handle
allowing grease to escape and moisture to get into the cavity.
then fill the cavity under the O-ring
When finished greasing the bearings, retighten the three screws.
on #14782 Blade Tension Screw with
Take care to also clean off any grease that was forced out of the
#374 Shell Cassida Grease EPS-2
cavity during greasing.
and re-assemble.
7. MOTOR BEARINGS: Bearing grease will lose its lubricating ability over time, not suddenly. The
lubricating ability of a grease (over time) depends primarily on the type of grease, the size of the bearing,
the speed at which the bearing operates and the severity of the operating conditions. Good results can be
obtained if the following recommendations are used in your maintenance program.
A high grade ball or roller bearing grease should be used. Recommended grease for standard service
conditions is Polyrex EM (Exxon Mobil).
Equivalent and compatible greases include: Texaco Polystar, Rykon Premium #2, Pennzoil Pen 2 Lube,
and Chevron SRI.
Recommended lubrications intervals is every 12 months with the equivalent of two (2) teaspoons of grease.
If motor does not have zerk fittings, the motor bearings are sealed for life.
14
OPERATOR’S NOTES
15
16
17
18
ITEM No. 14782K Blade Tension Screw Conversion Kit
INSTALLATION INSTRUCTIONS
Disconnect the machine from main power supply.
Loosen tension on the saw blade and remove the upper wheel assembly.
Unbolt the (A) tensioning handle from the (B) blade tension screw.
At the bottom handle mount turn the (B) blade tension screw clockwise until it can be lifted out of the (C) housing.
Apply a good food grade grease to the replacement (D) tension screw and install into the (C) housing turning
counterclockwise until it bottoms out.
Replace the (A) tensioning handle. Be sure the (E) spring and (F) plunger pin are still present in the end of the
(A) handle.
Replace the upper wheel assembly and the blade.
Tension the blade.
19
Item No. Description Item No. Description
A16547 Lower bearing housing assembly w/o wheel 14560 Lower saw wheel, 14”
A363 Lower bearing cup/cone assembly 14560DF Lower saw wheel, 14”, double flange
HN25 Hex nut, ⅜ -16, SS 14740 Retaining ring- external
LW20S Lock washer, ⅜, SS 14746 T- handle lock, removable lower wheel
SSS05S Set screw cup, SS, 10-24 x ⅜ 16251-90X78AL Pulley, upper V-belt 9 x ⅞ AL
14544 Grease seal, 1½ ID 16517 Inner race spacer, removable wheel
14545 Retaining ring, internal, 2-7/16 ID 16543 Shaft, lower saw wheel
14548 Grease seal, ⅞ ID 16547 Lower bearing housing, removable wheel
14549 Lower bearing housing cap 280 Key
14550 Adjustment screw, lower bearing housing 360A1 Grease fitting angular
14551 Hex jam nut, ⅝ -11, SS 360B-1 Set screw ½-13
21
AS415D
STATIONARY BAR ASSEMBLY
23
Item No. Description Item No. Description
AS12132 Steel cleaner assembly, rear S235 Taper pin, #4 x ¾ SS
AS12290-3 Cleaning unit assembly S244 Wheel cleaner arm stud, SS
A295 Wheel cleaner assembly S295 Wheel cleaner arm, SS
HHS003S Hex head screw, 8-32 x ¼ trimmed, SS S325 Wheel cleaner arm stud washer, SS
HHS004S Hex head screw, 8-32 x ⅜, SS S608 Saw back-up guide w/607 carbide
HHS009S Hex head screw, 10-24 x ¼, SS 131 Blade cleaner, SS
HHS055S Hex head screw, 5/16-18 x ¾, SS 131N Blade cleaner, nyleen
HN05S Hex nut, 8-32 SS 131SHORT Blade cleaner, Short SS, 19/16 LG
LW15S Lock washer, 5/16 SS 131SS-NYL Blade cleaner combo, Short SS & Nyleen
S12132 Cleaning unit, rear 179 Wheel cleaner
S12290-3 Cleaning unit 211Q Lock knob, 5/16-18, 4 point
S229 Wheel cleaner arm spring, SS 14640 Wheel cleaner, Rulon
24
WATERTIGHT MAGNETIC SWITCH ASSEMBLIES
(AEG)
INCLUDES MOUNTING BRACKET AND WIRES
Item No. Description Item No. Description
A22616EE-514 BAEG/MS-PB/05-C8 2HP 208-220-50/60-3 A22616EE-5241 BAEG/MS-PB/A26 1.5-2HP 104/115-60-1
A22616EE-516 BAEG/MS-PB/05-E4.7 2HP 440/460-3 A22616EE-5261 BAEG/MS-PB/CS16 2HP 230-60-1
A22616EE-518 BAEG/MS-PB/05-D4.7 1.5-2HP 380/415-50-3 A22616EE-530 BAEG/MS-PB/05-F3.2 2HP 550/575-3
A22616EE-522 BAEG/MS-PB/05-C14 3HP 220-230-50/60-3 A22616EE-534 BAEG/MS-PB/05-E6.3 3HP 440/460-60-3
A22616EE-5221 BAEG/MS-PB/05-CS14 1.5HP 220/230-50/60-1 A22616EE-536 BAEG/MS-PB/05-D8 3HP 380-60-3
241WH
297-1
241GR
PU
T
241BL
STA
HN05S (4)
224-1
PU
SH
T
ST O
LW03S (4)
OP
224-1F
or
224-1N LW20S (2)
151
A16226A-SG
HHS070S (2)
225-3
or
225-1P
226-28 (2)
226EE-22PB-GE
or
42MC-Y73
226EE-22PB-RE
or
42MC-Y74
16296-2
or
16296-3
25
OPERATOR’S NOTES
26
115 VOLT WITH 6 LEADS
27
28
29
30
31
32
CLEANING
10 9 9
9
10
9 9
10
9
33
ER BRACKET 1433-34-3334-44-55
STEEL BLADE CLEANER CARRIAGE BEARING Item No. 16159
WEARABLE ORSAW CONTACT PARTSBIRO THATMANUFACTURING
WILL
CARRIAGE FIT BIRO BEARING POWER CUTTERS ALL SAWS
AWS ALL SAWS 11-22-33
0 Item No. 131 PH.:
Item419-798-4451
No. 159 E-Mail:
MODELS service@birosaw.com
1433-34-3334-44-55
RACKET STEEL BLADE CLEANER WEARABLE SAW PARTS
CARRIAGE 11-22-1433-33-34-3334-44-4436-55
BEARING THAT WILL ItemFITNo.BIRO 16159 POWER CUTTERS
CARRIAGE BEARING
S ALL SAWS WEARABLE — EXCEPT
11-22-33 SAW WHERE PARTS
MODELS NOTED THAT OTHERWISE
1433-34-3334-44-55
WILL — FIT
CONTACT Item YOUR NEAREST BIRO
11-22-1433-33-34-3334-44-4436-55 AUTHORIZED DISTRIBUTOR
Item No. 601 BIRO
No.
Item 601
No. 602B MODEL 1433FH Item ItemNo.No.602BS265 Item
Item
Item No.
No.
No.S265
119A
S608 Item No.
Item
UPPER SAW GUIDE BRACKET UPPER — EXCEPT
SAW OR GUIDECONTACT
WHERE
BRACKET
UPPER SAW GUIDE
BIRO
NOTED MANUFACTURING
OTHERWISE
UPPER SAW
MEAT GAUGE SPRING GUIDE— MEATLOWER GAUGE
LOWER BLADE BACKUPSAW SPRING
GUIDE LOWER BLAD
S265 Item No. S608 CONTACT YOUR Item No. 119A NYL
ALL SAWS PH.:
ALL 419-798-4451
SAWS
NEAREST
W/BEVELED E-Mail:
BIRO AUTHORIZED
CARBIDE service@birosaw.com
W/BEVELED ALL SAWSCARBIDE
DISTRIBUTOR Item ALL SAWS
ALL No.
W/CARBIDESAWS 177 W/CAR
ItemAL
E SPRING LOWER BLADE BACKUP LOWER ALL SAW SAWS GUIDE 22 (after S/NBL 35
OR CONTACT ALL SAWS BIRO MANUFACTURING NYLON
22 (after FILLER
S/N 35301)-1433-55 LOWER
WS
o. 601 W/CARBIDE Item No. 602B Item No. S265 ALLNo.
Item SAWSS608 ALL SAWS W/CA
UIDE BRACKET 22 (after S/N Item
UPPER No. 130GUIDE PH.:MEAT
35301)-1433-55
SAW 419-798-4451
Item No. 131SPRING
GAUGE E-Mail: LOWER
service@birosaw.com
Item BLADENo. 159 BACKUP
Item No. 16159 11-22 (befo
SAWS SAW CLEANER
W/BEVELED CARBIDE BRACKET STEEL BLADE
ALL SAWS CLEANER CARRIAGE
W/CARBIDE BEARING
1 ItemALL No. SAWS
602B ItemALLNo. S265SAWS 11-22-33 CARRIAGE BEARING
ALL SAWS 22 Item
(afterNo.S/N S608
35301)-1433-55
BRACKET UPPER SAW GUIDE MEAT GAUGE SPRING LOWER BLADE BACKUP 1433-34-3334-44-55
S W/BEVELED CARBIDE ALL SAWS W/CARBIDE
ALL SAWS 22 (after S/N 35301)-1433-55 It
Item No. Item No. 119A
Item119A
No. 130 Item
Item GUIDE No.
No. 177 131 Item No.
Item 177
Item No. 604 No. 159 Item No.
Item 604
No. 605 Item WHE
No.
Item LOWER SAW Item FILLER
No. 177BEARINGLOWER BLADE Item
Item No.No. 179
179 Item
SAWNo.
LOWER S119A
SAW
CLEANER GUIDEBRACKET Item
STEEL
NYLON
No. 131 CLEANER NYLON
BLADEFILLER LOWER CARRIAGEBLADE BACKUP LOWER Item
BLADE No. 16159
BACKUP
BACKUP LOWER BLADE A
4 Item No.
LOWER SAW
ALL 605 GUIDE
SAWS STEEL ALLBLADESAWS CLEANER NYLON
ALL SAWS FILLER WHEEL
WHEEL
CARRIAGE
W/CARBIDE CLEANER
CLEANER
BEARING WHEEL
W/CARB CLE
ALL SAWS ALL ALLSAWSSAWS W/CARBIDE 11-22-33 W/CARBIDE
ACKUP LOWER BLADE Item No. 130
BACKUP Item No. 131 Item No. 159 ALL
S/NSAWS
1433-34-3334-44-55 WEARABLE SAWAL P
119A SAW CLEANER BRACKET STEELItem BLADE CLEANER 11-22 (before
CARRIAGE S/N 35300) 11-22 Item (before
34-3334-44-4436
No.
Item16159
35300)
No. S295
34-3334-44
E W/CARBIDE Item No. 177 No. 604 Item No.BEARING 605
W35300)
GUIDE ItemSAWS
ALL
34-3334-44-4436
NYLON No. 601
FILLER LOWERALL Item
BLADE SAWSNo. 602B
BACKUP LOWER BLADE Item No.
11-22-33 S265
BACKUP CARRIAGE
WHEEL Item No. BEARING
CLEANER
S608 ARM
WS Item No. S295 1433-34-3334-44-55
11
UPPER SAW GUIDE
ALL SAWS BRACKET UPPER
W/CARBIDE SAW GUIDE MEAT
W/CARBIDE GAUGE SPRING LOWER ALL
BLADE SAWS
BACKUP
ALL SAWS W/BEVELED CARBIDE Item WHEELALL CLEANER ARM — EXCE
Item No. 177 Item
11-22 No. 604S/N 35300)
(before No. 605 SAWS
34-3334-44-4436 W/CARBIDE
IDE NYLON FILLER LOWER BLADE BACKUP ALL SAWS LOWER BLADE BACKUP
ALL SAWS 22 (after S/N CONTACT
35301)-1433-55 YOUR
ALL SAWS W/CARBIDE W/CARBIDE
ItemItem No.No.179S244 Item No. S244 OR CO
Item No. 179
11-22 (before S/N 35300)
WHEELItem CLEANER
34-3334-44-4436
WHEEL
WHEEL CLEANER CLEANER WHEEL CLEANER ARM STUD PH.: 419-N
Item
S244 Item No. 601 No. 602B ALL Item No.ARM
SAWS S265 STUD ALL
Item
Item
SAWS
No.
No.S229
S608
ALL SAWS ALLGAUGESAWS SPRING WHEEL CLEANER WHEEL
R ARM STUD UPPER Item SAW No. S229GUIDE BRACKET
S229 UPPER SAW GUIDE MEAT LOWER Item No. BLADES268
ItemBACKUP
No. 415D
Item No. ARM SPRING ARM S
WS Item ALL SAWS
No.601
179 W/BEVELED
Item CARBIDE ALL SAWS FILLER &W/CARBIDE
GUIDE STUD
WHEEL
WHEEL Item CLEANER
CLEANER
No. Item No.No.
Item S244
No. S244
602B Item
Item No.
No.
Item No. S268 S265
S265 ItemItem No.No.
ALL
STATIONARY
S268
S608
SAWS
BAR ALL
ItemCLEANER
No. S295 ALLARM SAWS 22 (afterALL S/N
SAWS35301)-1433-55
UPPER WHEEL ARM
ARM
SAW Item CLEANER
SPRING
No.
SPRING
GUIDE S295
BRACKET WHEEL
WHEEL
WHEEL
CLEANER
UPPER
CLEANER SAW ARM STUD
GUIDE
ARM
STUD MEAT MEATItem
FILLER GAUGE
&GAUGE No. SPRING
GUIDE
S229
SPRING
STUD LOWERFILLER & GUIDE
BLADE ALL
STUD
BACKUP SAWS
OWER CUTTERS WHEELItem
ALL No.
ALL SAWS
ALLCLEANER
119A
SAWS
SAWS ARM WEARABLE ALL
Item No.
W/BEVELED SAWS
177CARBIDE WHEEL
Item ALL No. CLEANER
604
SAWS Item No.
W/CARBIDE 605
LOWERItem No. SAW 179 GUIDE ALL
Item No. SAWSSAW PARTS THAT WILL
S244 ALL SAWS FIT BIRO POWER CUTTERS
ALL SAWS NYLON ALL FILLER
SAWS LOWER BLADE ARM SPRING BACKUP LOWER
22 (after S/N BLADE BACKUP
35301)-1433-55
WHEEL ALL SAWS
CLEANER WHEEL CLEANER ARM STUD MODELS
Item No.
ALL S229
SAWS
. S295 ALL SAWS
ALL SAWS
ALL SAWS 11-22-1433-33-34-3334-44-4436-55
WHEEL
W/CARBIDE
CLEANER
W/CARBIDE NOT TO SCALE
SE
ANER — ARM 11-22 (before S/N 35300) 34-3334-44-4436
Item No. 130 Item
— EXCEPT WHEREARM NOTED SPRING OTHERWISE SAW — CLEANER BRACKET STEEL BLA
DISTRIBUTOR
AWS
ALL SAWS
95 CONTACT YOUR ItemNEAREST
No. 415D BIRO AUTHORIZED Item No. 415D DISTRIBUTOR ALL SAWS Item No. S415D AL
NG Item No. 119A Item No. 177 Item No. 604 Item No. S415D Item No. 605
R ARM LOWER SAW GUIDE Item No.
OR CONTACT
STATIONARY
S268 FILLER
BIRO
BAR MANUFACTURING
STATIONARY BAR STAINLESS STATIONARY B
w.com Item No. S268 NYLON LOWER BLADE ALLSTAINLESS
BACKUP
SAWS STATIONARY
LOWER BLADE BARBACKUP
S Item No. S415D ALL SAWS FILLER & GUIDE PH.: 419-798-4451
STUD ALL SAWS E-Mail: service@birosaw.com STD: 22 (after S/N 35301)-1433-55 STD: 22 (after S/N 35301)-143
STAINLESS STATIONARY FILLERItem No. & GUIDE
BAR 119A STUD ALL SAWS W/CARBIDE W/CARBIDE
ALL ItemSAWSNo. 177 Item No.No. 604S244 Item No. 605 OPT: 3334-44
TD: 22 (after S/N LOWER ALL
35301)-1433-55 SAW SAWS Item No. 415D
GUIDE Item No. 179 Item No. 11-22
S415D Item
(before S/N 35300)OPT: 3334-44 34-3334-44-4436
NYLON
STATIONARY BAR WHEEL CLEANER FILLER LOWER
WHEEL CLEANERBLADE BACKUPARM STUD LOWER BLADE BACKUP
OPT: 3334-44ALL SAWS STAINLESS NOT TO SCALE Item No. S229
S268 WEARABLE
ALL SAWS SAW
ALLALL PARTS
SAWSSAWS NOT
STD:
THAT
22
TOSTATIONARY
(after
SCALE
WILL
S/N
FITALL
W/CARBIDE BIRO
35301)-1433-55
BAR
SAWS POWER CUTTERS W/CARBIDE
WHEEL CLEANER
IDE STUD 11-22 (before S/N 35300) 34-3334-44-4436
WS
Item No. 415D ItemMODELS
No.
OPT:S415D
3334-44 ARM SPRING
STATIONARY BAR 11-22-1433-33-34-3334-44-4436-55
STAINLESS STATIONARY BAR ALL SAWS
Item No. S295
ALL SAWS Item No.
No. 601
601 It
STUD Item No.
WHEEL CLEANER ARM NOT
S295 TO SCALE— EXCEPT STD: WHERE
22Item No.
(after NOTED
S415D
S/N OTHERWISE
35301)-1433-55 —
UPPER SAW
Item
GUIDEBRACKET
BRACKET UPPE
WHEEL CLEANER ARM Item No. 179
STAINLESS STATIONARY
OPT:BIRO3334-44 BAR Item No. S244 UPPER SAW GUIDE
9 ALL SAWS CONTACT YOUR NEAREST
WHEEL Item CLEANER
AUTHORIZED DISTRIBUTOR
WHEEL CLEANER ARM ALL SAWS W/BEV
Item No. 16159 Item No. 130 No. 131 Item No. 159STUD Item No. S229
ARING OR STEELCONTACT BIRO MANUFACTURING Item No. 16159
CARRIAGE BEARING SAW NOT TO SCALE
CLEANER BRACKET
PH.: Item
ALL
No. 179
419-798-4451
SAWS
BLADE CLEANER ALL
CARRIAGE
Item No. S244
E-Mail: service@birosaw.com
SAWS BEARING WHEEL CLEANER
CARRIAGE BEARING
1433-34-3334-44-55 ALL SAWS WHEEL CLEANER
ALL SAWS
WHEEL CLEANER ARM STUD
11-22-33 ARM SPRING
Item 1433-34-3334-44-55
No.
ALL S229
SAWS
Item No. S295 ALL SAWS ALL SAWS WHEEL CLEANER
WHEEL CLEANER ARM Item No. 415D Item No. S415D ARM SPRING
ALL SAWS STATIONARY BAR STAINLESS STATIONARY BAR
Item No. S268 ALL SAWS
Item No. S295 ALL SAWS STD: 22 (after S/N 35301)-1433-55
FILLER &
WHEEL CLEANER ARM GUIDE STUD
ALL OPT: 3334-44
ALLSAWS SAWS Item No. 119A Item
LOWER SAW GUIDE
S265 Item No. S608 NOT TO SCALE ALL SAWS
NYLO
Item No.ItemS608
No.Item
130 No. 601 Item No. 131 ItemNo.
Item
Item No.602B
No. 415D
S602B Item No. 159 Item No. S265Item No. S415D Item No. S608 AL
SPRING LOWER BLADE BACKUP STATIONARY BAR Item No. 16159
LOWER SAW CLEANER
UPPER
BLADE
Item No. SAW BRACKET
BACKUP
S268GUIDE STEEL
BRACKET BLADE CLEANER
UPPER SAW
UPPER SAW GUIDE GUIDE CARRIAGE MEATBEARING
GAUGE SPRING
STAINLESS STATIONARY LOWER
Item No. 16159 BLADE
BAR BACKUP
WS W/CARBIDE ALL SAWS
22 (afterFILLER
ALL
w/ CARBIDE
S/N
SAWS
& GUIDE
35301)-1433-55
ALLSTUD
SAWS ALLW/BEVELED
SAWS
W/
ItemBEVELED
No. 415D CARBIDE 11-22-33ALL
CARBIDE 22 (afterCARRIAGE
STD:SAWS S/N BEARING
35301)-1433-55
CARRIAGE W/CARBIDE
BEARING
ALL SAWS Item No.
OPT: S415D
1433-34-3334-44-55
3334-44 22 (after S/N 35301)-1433-55
ALL SAWS STATIONARY BAR STAINLESS STATIONARY BAR
Item No. S268 ALL SAWS
FILLER & GUIDE STUD NOT TO SCALE STD: 22 (after S/N 35301)-1433-55
OPT: 3334-44
ALL SAWS
Ite
NOT TO
NOT TO SCALE
SCALE WHEE
AL
4 Item No. 605 Item No. 119A
Item No. 601 Item No.
Item602BNo. 177 Item No.ItemS265
No. 604 Item No. S608
Item No. 605
ACKUP LOWER BLADE LOWER BACKUPSAW GUIDE
UPPER SAW GUIDE BRACKET UPPERNYLON SAW GUIDE FILLER USEMEAT LOWER GAUGE
PARTS BLADESPRING
REPAIRBACKUP LOWER
KIT Item
LOWER
PART No. NO.
BLADE S295
BACKUP
BLADE BACKUP
12700-2
E W/CARBIDE ALL SAWS WHEELW/CARBIDE CLEANER ARM
ALL SAWS W/BEVELED ALL CARBIDE
SAWS ALLW/CARBIDE
SAWS W/CARBIDE
35300) 34-3334-44-4436
ALL SAWS 34 11-22 (before S/N 35300) 22 (afterALL SAWS
S/N34-3334-44-4436
35301)-1433-55
MODEL 1433FH
PART NUMBERS AND DESCRIPTIONS
MODEL NO. AND SERIAL NO. REQUIRED WHEN ORDERING PARTS
Item no. Description Item no. Description
AN15S Acorn nut ¼-20, SS 12273RH-3 Meat gauge bracket, RH
AN20S Acorn nut, ⅜-16, SS 12700-2 Wearable parts replacement kit
CB98S-316 Carriage bolt,⅜-16 x 2¾, 316 SS 131 Saw cleaner, SS
HHS048S Hex head screw, ¼-20 x 1¼, SS 14003U-6 Upper wheel, 14”
HHS0481S Hex head screw, ¼-20 x 1½, SS 14003UDF-6 Upper wheel, 14”, double flange
HHS049NL Hex screw- nylon 5/16-18 x ½ LG 14212W Platter rod
HHS050S Hex head screw, 5/16-18 x ⅝, SS 14232 Scrap bucket
HHS060S Hex head screw, 5/16-18 x 1, SS 14255 Saw guard on saw guide bar w/ 708 decal
HHS067S Hex head screw, ⅜-16 x ¾, SS 14256 Junction box
HN30S Hex nut, ⅜-16, SS 14275 Meat gauge arm
LW15S Lock washer, 5/16,SS 14275-5 Meat gauge plate, SS
LW20S Lock washer, ⅜, SS 14301-B Name & model plate (Serial number req’d)
M66-35M388S508-B Motor, 2HP 230-50-1 open 14302HT Saw blade, 108”
M66-35M388X966-B Motor, 2HP 115/230-60-1 open 14313FH-304 Operating and service manual
M68-M3558T-B Motor, 2HP 208-230/440-460-60-3 TEFC 14544 Grease seal, 1.50 ID
SSS11SB Set screw, ¼-20 x ¼, w/ brass tip 14545 Retaining ring, internal, 27/16 ID
SSS15S Set screw, 5/16-18 x 5/16, cup point 14548 Grease seal, ⅞ ID
S116-22 Saw guide bar 22”, SS 14549 Lower bearing housing cap
S119A Saw guide in stationary bar 14550 Adjustment screw, lower bearing housing
S12132 Cleaning unit, rear 14551 Hex jam nut, ⅝-11, SS
S12290-3 Front blade, wheel cleaning unit 14560 Lower saw wheel, removable
S14005E Fixed head, SS 14560DF Lower saw wheel, removable, double flange
S14006E Head door for fixed head, SS 14746 T-handle lock, removable lower wheel
S14007 Channel bracket, SS 14779-1 Blade tension cap gauge
S14214 Side platter bracket, SS 14780 Blade tension adjustment housing
S14217PD Base door left, SS, bolt on 14781 Blade tension adjustment handle
S14217R Base door right, SS, hinged 14782 Blade tension screw, SS
S14335XE Upper hinge bracket, fixed head, SS 14783 O-ring
S155-11 Meat carriage stop thumb screw, SS 14785 Plastic washer
S155B-1 Meat carriage stop, welded 14786 O-ring for gauge
S155EZ-3 Hex stand off 151 Conduit, watertight, per inch
S16120 Channel 16112 Head door latch
S163F Platter spacer weld button, SS 16155EZ Meat carriage, EZ flow
S200B1 Stop stud on saw guide bar 16159 Meat carriage bearing
S217C Base door hinge pin, long, SS 16163B Platter neck guard
S217E Base door hinge pin, short, SS 16200 Carriage stop, movable
S229 Wheel cleaner arm torsion spring, SS 16220-1 Carriage stop, fixed
S235 Taper pin, SS 4 x ¾ 16251-90X78AL Upper V-belt pulley, 9 x ⅞, aluminum
S239-B40 Base foot welded, short, SS 163A Platter rod clip
S239-B41-4 Adjustable leg bolt, SS 16517 Inner race spacer, removable wheel
S242R Base door lock, right, SS 16543 Lower shaft
S244 Wheel cleaner arm stud, SS 16547 Lower bearing housing, removable wheel
S249 Base door handle 17211-22 Finger lift shim, .022
S252X Upper shaft lock nut, SS 17211-35 Finger lift shim, .035
S253 Upper wheel aligning screw, SS 175-1-S Thumb guard nut
S262 Meat gauge release handle, SS 175-2-S Thumb guard screw ¼-20
S264-1 Meat gauge release hand wheel 175S Thumb guard, nylon
S265 Meat gauge release spring, SS 177 Stationary bar nylon filler
S268 Stationary bar headless screw, SS 179 Wheel cleaner
S270 Meat gauge release pin w/ holes, SS 18120EZ-B3 Guide bar, EZ flow, T-shaped
S295 Wheel cleaner arm, SS 194 Saw guide bar lock pad, brass
S325 Wheel cleaner arm washer, SS 194KS-1 Saw guide bar lock knob assembly
S360CB-1 Carriage bolt, ⅜-16 x 1¼, SS 196-2 Saw tension spring, fixed head
S415D Stationary bar, SS 211 Finger lift bracket
S416 Platter locator weld pin, SS 211A-291Q Finger lift fastener knob, 4-point
S608 Lower blade back-up guide w/ carbide 211Q Fastener knob, 4 point. 5/16-18
S71-3 Upper wheel hinge bracket, fixed head 212CP Platter rod cotter pin
112-212 Waved washer 221-52 V-belt, 52”
119FSC Saw guide in stationary bar, fish 221-53 V-belt, 53”
12273LH Meat gauge bracket, LH 224 Conduit connector, straight
35
MODEL 1433FH PART NUMBERS AND DESCRIPTIONS (Cont.)
MODEL NO. AND SERIAL NO. REQUIRED WHEN ORDERING PARTS
36
OPERATOR’S SIGNATURE PAGE
WARNING
READ AND UNDERSTAND THIS ENTIRE
MANUAL BEFORE SIGNING BELOW
MY SIGNATURE ATTESTS THAT I HAVE COMPLETELY READ AND UNDERSTAND
THIS MANUAL. I REALIZE THAT THIS MACHINE, IF OPERATED CARELESSLY, CAN
CAUSE SERIOUS INJURY TO MYSELF AND OTHERS.
37
LIMITED WARRANTY:
WARRANTY: The BIRO Manufacturing Company warrants that Model 1433FH will be free from defects in
material and workmanship under normal use and with recommended service. BIRO will replace defective parts,
which are covered by this limited warranty, provided that the defective parts are authorized for return, shipping
charges prepaid, to a designated factory for inspection and/or testing.
DURATION OF WARRANTY: The warranty period for all parts covered by this limited warranty is one (1)
year from date of Inspection/Demonstration advised on the returned Warranty Registration Card, or eighteen
(18) months from original factory ship date, whichever occurs first, except as noted below.
PARTS NOT COVERED BY WARRANTY: The following are not covered by this limited warranty:
wearable parts on the cleaning system such as wheel cleaners (Item No. 179), saw blade cleaners (Item No. 131)
blade backup guides (Item No’s. 602B, 605, S608 and S119A), and the nylon filler (Item No. 177). This limited
warranty does not apply to machines sold as used, rebuilt, modified, or altered from the original construction in
which the machine was shipped from the factory. (WATER CONTAMINATED ELECTRICAL SYSTEMS ARE
NOT COVERED UNDER THIS LIMITED WARRANTY.) BIRO is not responsible for electrical connection of
equipment, adjustments to switch controls or any other electrical requirements, which must be performed only
by a certified electrician. BIRO is not responsible for service charges or labor required to replace any part
covered by this limited warranty or for any damages resulting from misuse, abuse, lack of proper or
recommended service.
EXCLUSION OF WARRANTIES AND LIMITATION OF REMEDIES: BIRO gives no warranties other
than those expressly stated in this limited warranty. THE IMPLIED WARRANTY OF MERCHANTABILITY,
THE IMPLIED WARRANTY OF FITNESS FOR PROCESSING FOOD PRODUCTS, AND ALL OTHER
IMPLIED WARRANTIES ARE SPECIFICALLY EXCLUDED. BIRO IS NOT LIABLE FOR CONSEQUEN-
TIAL OR INCIDENTAL DAMAGES, EXPENSES, OR LOSSES. THE REMEDIES PROVIDED IN THIS
BIRO LIMITED WARRANTY ARE PURCHASER’S SOLE AND EXCLUSIVE REMEDIES AGAINST
BIRO.
REGISTRATION CARDS: You must sign, date and complete the warranty registration card supplied with
each machine. The warranty card must be returned to The BIRO Manufacturing Company for proper registra-
tion. If no warranty card is returned to BIRO, the warranty period will begin from the date the machine was
originally shipped from the factory.
HOW TO GET SERVICE:
1. Contact the agency from whom you purchased the machine; or
2. Consult the yellow pages of the phone directory for the nearest authorized dealer; or
3. Contact Biro Manufacturing Company for the nearest authorized service entity in your area.