F15 / F21 /

F31 / F41 / F61

Service Manual
 Table of Contents

General Installation Check List ................................................................01

Valve Start-up Procedure ........................................................................03

Dimensional Drawings ............................................................................07

Timer Assembly ......................................................................................12

Control Drive Assembly ...........................................................................18

Valve Body Assembly ..............................................................................28

Brine Valve Assembly ..............................................................................38

Meter Assembly ......................................................................................41

Wiring Diagram ....................................................................................45

Trouble Shooting ....................................................................................49

 General Installation Check List

1. The Surroundings Of Installation

Water Pressure A minium of 0.2 Mpa of water pressure is required for valve to operate effectively.

Electrical Facilities A continuous current supply is required, check voltage compatibility.

Existing Plumbing Condition of existing plumbing should be free from any deposit such as lime and
iron build up. Piping that is clogged heavily with these deposit should be cleaned in
time and connect according to plumbing codes.

Location Of Installation The softener should be located close to a drain pipe

By-pass Valves Always provide for the installation of a by-pass valve

CAUTION

Water pressure is not to exceed 0.8Mpa

W ater temperature is not to exceed 38℃
WARNING

The unit cannot be subjected to freezing conditions.

2. Instruction Of Valve Installation And Resin Filling

①Fit the distrubutor firmly to the bottom of the central tube, cut the tube from the point
that is 0.5mm lower than the top of the tank and chamfer ,then insert it into the central
of resin tank ,and seal the central tube with tape in case of the resin leakage.

②Add sand to fill the space around the central tube unit it is 20 mm above the bottom
distributor. The sand should be paved based on the graded particle size in order to
distribute the water. No need to fill the tank with sand if the diameter of the tank is less
than 500 mm.

③F ill the tank evenly with sand to the standard height then add 10% salt water until it
overflows the resin. Let resin fully expands. then take off the tape on the central tube
and keep it always in the middle of tank .

④To install the top distributor on the valve, then insert the central tube into valve
through top distributor, and carefully turns the valve clockwise until it screws tightly
on the tank .( Pay attention: valve and tank mouth, top distributor and valve、central
tube, buttom distributor and central tube must be sealed, in case of the resin leakage;
central tube and valve must be sealed, other wise the water will leak).

01
 General Installation Check List

3. Pipe Connection
①To connect the in-outlet pipe according to the valve's dimension (water supply pipe
should not less than inlet pipe for keeping sufficient flow).

②The manual valve should be installed on the in-outlet pipe, the bypass valve should be
installed between in-outlet pipe, the sampling valve should be installed before the
outlet pipe, the Y filter is recommended to installed on the inlet pipe; in case of the
deposit in the pipe would clog the valve and make the system can't work well.

③The length of drain pipe should not exceed 6 m, tr y to avoid bending.

④The length of the pipe for brine water should be less than 2 meters, keep the pipes
sealed in good condition, other wise it may influence the regeneration effect.

4 . S ystem Adjustment
① Wash the deposit away from the pipe. To set the bypass valve in bypass position, wash
the deposit away from the pipe until the water runs clean. Then close the inlet-outlet
valve, and set the bypaass valve to ser vice position.

② To set the valve on the ser vice position, open the inlet valve,to refill the water into the
resin tank until the water stop flowing. Open the outlet valve to clean up the air and
deposit of the resin tank .

③ To set the valve on backwash position, and the water outflow from drainage for 3-4
minutes. Keep draining off the water until the water is clean.

④ To set the valve on the brine position,and suck the water from brine tank until stop.

⑤ To set the valve on refill postion, refill the salt and water into the tank until exceed the
air check valve. Note: keep the salt water for 6 hours.

⑥ To set the valve on ser vice postion, check if the bypass valve is in ser vice postion and
the out water is qualified.

02
 Valve Start-up Procedure

Mechanical valve has 3 type: timer, meter immediately, meter delayed.

The current time of day should be set before operating the timer or meter delayed valves, but no
needs for meter immediate valve.
How to set the time of day:
① Press and hold the time set button to disengage the 24 hour gear.
② Turn the 24 hour gear until the actual time of day is at the time of day pointer.

NOTE: the 24 hour gear would stop running when power fails, it needs to reset the time of day
when the power switched on.

24 Hour Gear

Time Indication

Time Set Button

1. Model timer

Manual
Regeneration Knob
24 Hour Gear Regeneration Timer Pointer Screw

TO SET TIME OF DAY-

PRESS WHITE BUTTON AND TO SET TIME OF DAY-
TURN LARGE DIAL UNTIL PRESS WHITE BUTTON AND
TIME IS AT ARROW. TURN LARGE DIAL UNTIL
TO MANUALLY START TIME IS AT ARROW.
CYCLE-TURN KNOB TO MANUALLY START
CLOCKWISE. CYCLE-TURN KNOB
CLOCKWISE.

Gap

Red pointer
TI
M
EO

TI
M
FD

EO
AY

FD
AY

Time Indication

Time Set Button Skipper Wheel

Mechanical valve was defaut set the regeneration time at 2:00 AM before leave factor y, it means after
setting time of day, the regeneration starts when 2:00AM on the 24 hour gear and time indication arrow
in same point.

03
 Valve Start-up Procedure
1.1.How to adjust the regeneration time
①Disconnect the power source .
②Locate the three screws behind the manual regeneration knob by pushing the red button in and rotating
the 24 hour dial until each screw appear in the cut out portion of the manual regeneration knob.
③Loosen each screw slightly to release the pressure on the time plate from the 24 hour gear.
④Locate the generation time pointer on the inside of 24 hour dial in the cut out.
⑤Turn the time plate so the desired regeneration time aligns next to the raised arrow .
⑥Push the red button in and rotate the 24 hours dial . Tighten each of the three screws .
⑦Push the red button and locate the pointer one more time to ensure the desired regeneration time is
correct.
⑧Reset the time of day and restore power to the unit.
NOTE: the 24 hour gear would stop running when power off, it should be reset when the power switched on.

1.2. How to set the inter val days of regeneration

The skipper wheel indicates 12 days on the timer model, ever y tab presents one day. the tab at the red
pointer is today. Pull or push the tab to set the regeneration date. For example, firstly push down all the
tabs then pull up the tab ever y other one, the valve will regenerate ever y other day. For example, pull all
the skipper wheel pieces firstly, then pick up ever y other one, that means the regeneration date is
regenerate one time ever y other day.

2. M odel Meter

24Hour Gear Manual Regeneration Knob

TO SET TIME OF DAY-

PRESS WHITE BUTTON AND
TURN LARGE DIAL UNTIL
TIME IS AT ARROW.
TO MANUALLY START
CYCLE-TURN KNOB
CLOCKWISE.
Capacity
CAPACITE
CAPACIT..Y
(gallons remaining or M remaining)
KAPAZITAT
CAPACITA
CAPACIDAD
GAL

Program wheel
TI
M
EO
FD
AY

Time Set Button

White Dot Gallon Label(or M label)

NOTE: Immediate regeneration times do not have 24 hours gear, no time of day can be set. And they have
same way to set the regeneration.

2.1.How to set the regeneration cycle program

① Pull out the cable from the meter.
② Set program wheel by lifting the middle small dial and rotating it until the desired capacity on the
label aligned with the white dot.
③ Release the middle small dial and check for firm engagement at setting.
④ R otate the manual regeneration knob and let the program wheel return to the position.
⑤ R e-insert the meter cable back .

04
 Valve Start-up Procedure

3. How to manual regenerate

Turn the manual regeneration knob clockwise until hear the clatter. This sight movement will switch on
the micro switch attached and starts the regeneration. Program wheel would spend about 3 hours for
rotate a cycle .it's also available to clockwise rotate manual regeneration knob until to the next desired
regeneration steps, but before next step, please wait the motor running to corresponding regeneration
step and stop.

NOTE: Don't rotate the manual regeneration knob before the motor stop. If the program wheel and
piston on the valve runs in different position, please cut the power and check the valve position first,
then rotate the manual regeneration knob to corresponding position, then apply the power again.

4. How to set the regeneration cycle program

Pin Storage
Brine &Rinse Section
Program Wheel
( 2 Min. Per Hole)

Repid Rinse Section

( 2 Min. Per Pin)

Back Wash Brine Tank

(2 Min. Per Pin) ( 2 Min. Per Hole )

the back of timer

① The regeneration cycle program on your water conditioner has been factor y preset, however,
portions of the cycle or program may be lengthened or shortened in time to suit local conditions.

② To expose cycle program wheel , grasp timer in upper left - hand corner and pull, releasing snap
retainer and swinging timer to the right.
To change the regeneration cycle program the program wheel must be removed. Grasp program
wheel and squeeze protruding lugs towards center, lift program wheel off timer.(Switch arms may
require movement to facilitate removal.)
Return timer to closed positions engaging snap retainer in back plate. Make certain all electrical
wires locate above snap retainer post.

05
 Valve Start-up Procedure

How To Change The Length Of The Backwash Time:

The program wheel as shown in the drawing is in the ser vice position. As you look at the numbered
side of the program wheel, the group of pins starting at zero determines the length of time your
unit will backwash.
FOR EXAMPLE: If there are six pins in this section, the time of backwash time will be 12 min. (2 min.
Per pin).To change the length of backwash time, add or remove pins as required. The number of pins
times two equals the backwash time in minutes.

How To Change The Length Of Brine And Rinse Time:

The group of holes between the last pin in the backwash section and the second group of pins
determines the length of time that your unit will brine and rinse (2 min. Per hole.)
To change the length of brine and rinse time, move the rapid rinse group of pins to give more of
fewer holes in the brine and rinse section. Number of holes time two equals brine and rinse time in
the minutes.

How To Change The Length Of Rapid Rinse:

The second group of pins on the program wheel determines the length of time that your water
conditioner will rapid rinse.(2 min. Per pin.)
To change the length of rapid time, add or remove pins at the higher numbered end of this section
as required. The number of pins times two equals the rapid rinse time in minutes.

How To Change The Length Of Brine Tank Refill Time:

The second group of holes in the program wheel determines the length of time that your water
conditioner will refill the brine tank .(2 min. Per hole.)
To change the length of refill time, move the two pins at the end of the second group of holes as
required.
The regeneration cycle is complete when the outer micro-switch is tripped by the two pin set at end
of the brine tank refill section. The program wheel, however, will continue to rotate until the inner
micro-switch drops into the notch on the program wheel.

06
 Dimensional Drawing

F15

The unit of the number in brackets is inch,rest is millimeter.

07
 Dimensional Drawing

F21

The unit of the number in brackets is inch,rest is millimeter.

08
 Dimensional Drawing

F31

The unit of the number in brackets is inch,rest is millimeter.

09
 Dimensional Drawing

F41

The unit of the number in brackets is inch,rest is millimeter.

10
 Dimensional Drawing

F61

The unit of the number in brackets is inch,rest is millimeter.

11
Timer Assembly

Time - Clock Timer

12
 Timer Assembly

Time - Clock Timer

Item No. Quantity Part No. Description

1 ……………………… 1 ……………………… 13206 ……………………… Ider shaft
2 ……………………… 1 ……………………… 13253 ……………………… Spring
3 ……………………… 1 ……………………… 13205 ……………………… Ider gear
4 ……………………… 1 ……………………… 13204 ……………………… Drive gear
5 ……………………… 1 ……………………… 15650 ……………………… Motor mounting plate
6 ……………………… 1 ……………………… 07057 ……………………… Wire
7 ……………………… 2 ……………………… 07011 ……………………… Terminal
8 ……………………… 4 ……………………… 02106 ……………………… Screw
9 ……………………… 3 ……………………… 02008 ……………………… Screw
※ 10 ……………………… 1 …………………………………… ……………………… Motor
11 ……………………… 2 ……………………… 02081 ……………………… Screw
12 ……………………… 1 ……………………… 33104 ……………………… Switch assy
13 ……………………… 1 ……………………… 06051 ……………………… Insulator
14 ……………………… 1 ……………………… 06002 ……………………… Switch
15 ……………………… 1 ……………………… 13214 ……………………… Stretch pin
16 ……………………… 1 ……………………… 13211 ……………………… Cycle actuator staff
※ 17 ……………………… 1 ……………………… B0006 ……………………… Time gear assy
18 ……………………… 1 ……………………… 13215 ……………………… Knob
19 ……………………… 1 ……………………… 13281 ……………………… Label
20 ……………………… 1 ……………………… 02107 ……………………… Screw
21 ……………………… 1 ……………………… 13210 ……………………… Pointer
22 ……………………… 1 ……………………… 66109 ……………………… Skipper wheel assy
23 ……………………… 3 ……………………… 09001 ……………………… Ball
24 ……………………… 2 ……………………… 13254 ……………………… Spring
25 ……………………… 1 ……………………… 13208 ……………………… Skipper wheel ring
26 ……………………… 1 ……………………… 13250 ……………………… Hinge bracket
27 ……………………… 2 ……………………… 02004 ……………………… Screw
28 ……………………… 1 ……………………… 13212 ……………………… Timer housing
29 ……………………… 1 ……………………… B0003 ……………………… Program wheel assy
30 ……………………… 1 ……………………… 13203 ……………………… Main drive gear
31 ……………………… 1 ……………………… 13252 ……………………… Spring

※For more options

13
 Timer Assembly

Meter Imm. Timer

14
 Timer Assembly

Meter Imm. Timer

Item No. Quantity Part No. Description

1 ……………………… 1 ……………………… 13206 ……………………… I der shaft
2 ……………………… 1 ……………………… 13154 ……………………… S pring
3 ……………………… 1 ……………………… 13205 ……………………… I der gear
4 ……………………… 1 ……………………… 13204 ……………………… D rive gear
5 ……………………… 1 ……………………… 15650 ……………………… M otor mounting plate
6 ……………………… 1 ……………………… 07057 ……………………… Wire
7 ……………………… 2 ……………………… 07011 ……………………… Terminal
8 ……………………… 5 ……………………… 02106 ……………………… S crew
9 ……………………… 3 ……………………… 02008 ……………………… Screw
※ 10 ……………………… 1 …………………………………… ……………………… Motor
11 ……………………… 1 ……………………… 12271 ……………………… Soft shaft
12 ……………………… 1 ……………………… 13106 ……………………… Spring retainer
13 ……………………… 1 ……………………… 13151 ……………………… Spring
14 ……………………… 1 ……………………… 13110 ……………………… Clutch
15 ……………………… 1 ……………………… 13111 ……………………… Drive pinion
16 ……………………… 1 ……………………… 06002 ……………………… Switch
17 ……………………… 1 ……………………… 06051 ……………………… Insulator
18 ……………………… 1 ……………………… 33104 ……………………… Switch assy
19 ……………………… 2 ……………………… 02081 ……………………… Screw
20 ……………………… 1 ……………………… 13214 ……………………… Stretch pin
21 ……………………… 1 ……………………… 13212 ……………………… Timer housing
22 ……………………… 1 ……………………… 13102 ……………………… Cycle actuator gear
※ 23 ……………………… 1 ……………………… 13215 ……………………… Knob
24 ……………………… 2 ……………………… 13281 ……………………… Lable
25 ……………………… 1 ……………………… 13109 ……………………… Program wheel assy
26 ……………………… 1 ……………………… B0004 ……………………… Flow gear assy
27 ……………………… 1 ……………………… 13250 ……………………… Hinge bracket
28 ……………………… 2 ……………………… 02004 ……………………… Screw
29 ……………………… 1 ……………………… B0003 ……………………… Program wheel assy
30 ……………………… 1 ……………………… 13101 ……………………… Main drive gear

※For more options

15
Timer Assembly

Meter Delay Timer

16
 Timer Assembly

Meter Delay Timer

Item No. Quantity Part No. Description

1 ……………………… 1 ……………………… 13026 ……………………… Ider shaft
2 ……………………… 1 ……………………… 13253 ……………………… Spring
3 ……………………… 1 ……………………… 13205 ……………………… Ider gear
4 ……………………… 1 ……………………… 13204 ……………………… Drive gear
5 ……………………… 1 ……………………… 15650 ……………………… Motor mounting plate
6 ……………………… 1 ……………………… 07057 ……………………… Wire
7 ……………………… 2 ……………………… 07011 ……………………… Terminal
8 ……………………… 5 ……………………… 02106 ……………………… Screw
9 ……………………… 3 ……………………… 02008 ……………………… Screw
※10 ……………………… 1 …………………………………… ……………………… Motor
11 ……………………… 1 ……………………… 12271 ……………………… Soft shaft
12 ……………………… 1 ……………………… 13106 ……………………… Spring retainer
13 ……………………… 1 ……………………… 13151 ……………………… Spring
14 ……………………… 2 ……………………… 13110 ……………………… Clutch
15 ……………………… 1 ……………………… 13111 ……………………… Drive pinion
16 ……………………… 1 ……………………… 06002 ……………………… Switch
17 ……………………… 1 ……………………… 06051 ……………………… Insulator
18 ……………………… 1 ……………………… 33104 ……………………… Switch assy
19 ……………………… 2 ……………………… 02081 ……………………… Screw
20 ……………………… 1 ……………………… 13214 ……………………… Stretch pin
21 ……………………… 1 ……………………… 13212 ……………………… Timer housing
22 ……………………… 1 ……………………… 13102 ……………………… Cycle actuator gear
※ 23 ……………………… 1 ……………………… B0006 ……………………… Time gear assy
24 ……………………… 1 ……………………… 13215 ……………………… Knob
25 ……………………… 2 ……………………… 13281 ……………………… Lable
26 ……………………… 1 ……………………… 13109 ……………………… Program wheel assy
※ 27 ……………………… 1 ……………………… B0004 ……………………… Flow gear assy
28 ……………………… 1 ……………………… 13250 ……………………… Hinge bracket
29 ……………………… 2 ……………………… 02004 ……………………… Screw
30 ……………………… 1 ……………………… B0003 ……………………… Program wheel assy
31 ……………………… 1 ……………………… 13203 ……………………… Main drive gear
32 ……………………… 1 ……………………… 09001 ……………………… Ball
33 ……………………… 1 ……………………… 13252 ……………………… Spring

※For more options

17
Control Drive Assembly

F15、F21、F31 upper

18
 Control Drive Assembly

F15、F21、F31 upper

Item No. Quantity Part No. Description

※1 ……………………… 1 …………………………………………………………… Power cord
2 ……………………… 1 ……………………… 07003 ……………………… Strain relief
3 ……………………… 1 ……………………… 13200 ……………………… Timer 13200
……………………… 1 ……………………… 13100 ……………………… Timer 13100
……………………… 1 ……………………… 13100E ……………………… Timer 13100E
4 ……………………… 1 ……………………… 07012 ……………………… Strain relief
5 ……………………… 2 ……………………… 06051 ……………………… Insulator
▲ ……………………… 1 ……………………… 06051 ……………………… Insulator
6 ……………………… 2 ……………………… 06003 ……………………… Switch
▲ ……………………… 1 ……………………… 06003 ……………………… Switch
7 ……………………… 2 ……………………… 02081 ……………………… Screw
8 ……………………… 1 ……………………… 10003 ……………………… Connecting link
9 ……………………… 1 ……………………… 10005 ……………………… Connecting link pin
10 ……………………… 1 ……………………… 10030 ……………………… Drive cam
11 ……………………… 2 ……………………… 00103 ……………………… Pin
12 ……………………… 1 ……………………… 10004 ……………………… Pin
13 ……………………… 8 ……………………… 02006 ……………………… Screw
14 ……………………… 2 ……………………… 02056 ……………………… Screw
15 ……………………… 1 ……………………… 10001 ……………………… Bracket
16 ……………………… 1 ……………………… 19041 ……………………… Cover
17 ……………………… 1 ……………………… 19042 ……………………… Plate cover
▲ 18 ……………………… 2 ……………………… 02054 ……………………… Screw
19 ……………………… 1 ……………………… 10031 ……………………… Brine valve cam
20 ……………………… 1 ……………………… 10002 ……………………… Brine valve bracket
※ 21 ……………………… 1 …………………………………… ……………………… Motor
▲ 22 ……………………… 1 ……………………… 33106 ……………………… Terminal assy
▲ 23 ……………………… 2 ……………………… 02106 ……………………… Screw
24 ……………………… 1 ……………………… 19001 ……………………… Back plate
25 ……………………… 2 ……………………… 19043 ……………………… Plate plug(small)
26 ……………………… 2 ……………………… 19044 ……………………… Plate plug(middle)
27 ……………………… 4 ……………………… 02103 ……………………… Screw
28 ……………………… 1 ……………………… 19048 ……………………… Screw cap
29 ……………………… 1 ……………………… 19045 ……………………… Plate plug(big)

※For more options

▲Only fo F31

19
Control Drive Assembly

F31 lower

20
 Control Drive Assembly

F31 lower

Item No. Quantity Part No. Description

1 ……………………… 1 ……………………… 19102 ……………………… Back plate
2 ……………………… 1 ……………………… 19101 ……………………… Bracket
3 ……………………… 4 ……………………… 02006 ……………………… Screw
4 ……………………… 2 ……………………… 02055 ……………………… Screw
5 ……………………… 1 ……………………… 29509 ……………………… Drive bearing
6 ……………………… 1 ……………………… 00103 ……………………… Roll pin
7 ……………………… 1 ……………………… 29530 ……………………… Drive cam
8 ……………………… 1 ……………………… 19103 ……………………… Connecting link
9 ……………………… 1 ……………………… 10020 ……………………… U-pin
10 ……………………… 1 ……………………… 04051 ……………………… Retaining ring
11 ……………………… 2 ……………………… 02054 ……………………… Screw
12 ……………………… 1 ……………………… 06003 ……………………… Switch
13 ……………………… 1 ……………………… 06051 ……………………… Insulator
14 ……………………… 2 ……………………… 02104 ……………………… Screw
15 ……………………… 2 ……………………… 04002 ……………………… Washer
16 ……………………… 1 ……………………… 29541 ……………………… Transparent board
17 ……………………… 1 ……………………… 29539 ……………………… Housing
18 ……………………… 2 ……………………… 02002 ……………………… Screw
※ 19 ……………………… 1 …………………………………… ……………………… Motor
20 ……………………… 1 ……………………… 19048 ……………………… Lock relief

※For more options

21
Control Drive Assembly

F41、F61 upper

22
 Control Drive Assembly

F41、F61 upper

Item No. Quantity Part No. Description

1 ……………………… 1 ……………………… 19046 ……………………… Meter cable guide
2 ……………………… 2 ……………………… 19047 ……………………… Screw cap
3 ……………………… 2 ……………………… 03005 ……………………… Nut
4 ……………………… 7 ……………………… 02006 ……………………… Screw
5 ……………………… 1 ……………………… 10108 ……………………… Back plate
6 ……………………… 1 ……………………… 13200 ……………………… Timer 13200
……………………… 1 ……………………… 13100 ……………………… Timer 13100
……………………… 1 ……………………… 13100E ……………………… Timer 13100E
7 ……………………… 1 ……………………… 00102 ……………………… Roll pin
8 ……………………… 1 ……………………… 10101 ……………………… Bracket-motor
9 ……………………… 1 ……………………… 10106 ……………………… Drive bearing
10 ……………………… 1 ……………………… 10140 ……………………… Drive gear
11 ……………………… 1 ……………………… 04071 ……………………… Retainer ring
12 ……………………… 1 ……………………… 04052 ……………………… Retainer
13 ……………………… 1 ……………………… 31514 ……………………… Pin-drive link
14 ……………………… 1 ……………………… 10103 ……………………… Connecting link
15 ……………………… 1 ……………………… 04056 ……………………… Retaining ring
16 ……………………… 4 ……………………… 02104 ……………………… Screw
17 ……………………… 4 ……………………… 04002 ……………………… Washer
18 ……………………… 1 ……………………… 31549 ……………………… Look-in
19 ……………………… 1 ……………………… 31545 ……………………… Housing
20 ……………………… 2 ……………………… 02011 ……………………… Screw
21 ……………………… 4 ……………………… 02055 ……………………… Screw
22 ……………………… 2 ……………………… 10143 ……………………… Bushing
23 ……………………… 1 ……………………… 10142 ……………………… Drive pinion
24 ……………………… 1 ……………………… T0002 ……………………… Cam assembly
25 ……………………… 4 ……………………… 02052 ……………………… Screw-drive mounting
26 ……………………… 1 ……………………… 04006 ……………………… Washer
27 ……………………… 1 ……………………… 04055 ……………………… Retaining ring
▲ 28 ……………………… 1 ……………………… 33106 ……………………… Terminal assembly
29 ……………………… 1 ……………………… 10102 ……………………… Bracket-brine valve side
▲30 ……………………… 2 ……………………… 02106 ……………………… Screw
31 ……………………… 2 ……………………… 02083 ……………………… Screw
32 ……………………… 3 ……………………… 06003 ……………………… Switch
33 ……………………… 2 ……………………… 06051 ……………………… Insulator
34 ……………………… 1 ……………………… 10104 ……………………… Bracket switch
※ 35 ……………………… 1 …………………………………… ……………………… Motor
36 ……………………… 4 ……………………… 03004 ……………………… Nut
※ 37 ……………………… 1 …………………………………………………………… Power cord

※For more options

▲Only for F61

23
Control Drive Assembly

F61 lower

24
 Control Drive Assembly

F61 lower

Item No. Quantity Part No. Description

1 ……………………… 4 ……………………… 03004 ……………………… N ut
2 ……………………… 1 ……………………… 10108-1 …………………… B ack cover board
3 ……………………… 1 ……………………… 10101-1 …………………… B racket
4 ……………………… 5 ……………………… 02006 ……………………… S crew
5 ……………………… 1 ……………………… 00102 ……………………… P in
6 ……………………… 1 ……………………… 10142 ……………………… P inion, drive
7 ……………………… 1 ……………………… 04052 ……………………… R ing, retaining
8 ……………………… 1 ……………………… 31514 ……………………… P in, drive link
9 ……………………… 1 ……………………… 10103 ……………………… Link , drive
10 ……………………… 1 ……………………… 04056 ……………………… R ing, retaining
11 ……………………… 1 ……………………… 04071 ……………………… R ing, retaining
12 ……………………… 1 ……………………… 10140 ……………………… Drive gear
13 ……………………… 1 ……………………… 10106 ……………………… Bearing, drive link
14 ……………………… 2 ……………………… 10143 ……………………… Bushing
15 ……………………… 4 ……………………… 02055 ……………………… Bolt
16 ……………………… 1 ……………………… 31549 ……………………… Window
17 ……………………… 2 ……………………… 02011 ……………………… Screw
18 ……………………… 1 ……………………… 31545 ……………………… Cover
19 ……………………… 6 ……………………… 04002 ……………………… Washer
20 ……………………… 4 ……………………… 02104 ……………………… Screw
21 ……………………… 4 ……………………… 02052 ……………………… Bolt
22 ……………………… 1 ……………………… T0001 ……………………… Drive cam assembly
23 ……………………… 1 ……………………… 04055 ……………………… Ring, retaining
24 ……………………… 1 ……………………… 04006 ……………………… Washer
25 ……………………… 1 ……………………… 10102 ……………………… Bracket, brine side
26 ……………………… 2 ……………………… 02084 ……………………… Screw
27 ……………………… 1 ……………………… 06003 ……………………… Switch
28 ……………………… 1 ……………………… 06051 ……………………… Insulator
29 ……………………… 1 ……………………… 10104 ……………………… Bracket, switch mounting
※ 30 ……………………… 1 …………………………………… ……………………… Motor
31 ……………………… 1 ……………………… 19047 ……………………… Screw cap

※For more options

25
 Valve Body Assembly

F15

Filter

No Hard Water

26
 Valve Body Assembly

F15

Item No. Quantity Part No. Description

1 ……………………… 2 ……………………… 02051 ……………………… Screw
2 ……………………… 1 ……………………… 17056 ……………………… Injector cover
3 ……………………… 1 ……………………… 17031 ……………………… Injector cover gasket
※4 ……………………… 1 …………………………………………………………… Injector nozzle
5 ……………………… 1 ……………………… 17051 ……………………… Injector
6 ……………………… 1 ……………………… 17059 ……………………… Injector screen
※7 ……………………… 1 …………………………………………………………… Injector throat
8 ……………………… 1 ……………………… 17003 ……………………… Air disperser
9 ……………………… 1 ……………………… 17030 ……………………… Injector body gasket
10 ……………………… 1 ……………………… 29503-2 …………………… Vice-valve body
11 ……………………… 1 ……………………… 29511 ……………………… Drain connector
※12 ……………………… 1 …………………………………………………………… DLFC
13 ……………………… 1 ……………………… 01024 ……………………… O-ring
14 ……………………… 2 ……………………… 01025 ……………………… O-ring
15 ……………………… 1 ……………………… 27501 ……………………… Adapter base
16 ……………………… 1 ……………………… 01102 ……………………… O-ring
17 ……………………… 1 ……………………… 29508-1 …………………… Piston rod
18 ……………………… 1 ……………………… 66125 ……………………… Vice-end plug assy
19 ……………………… 1 ……………………… 29507-1 …………………… Vice-piston
20 ……………………… 6 ……………………… 29561 ……………………… Vice-seal
21 ……………………… 5 ……………………… 29535 ……………………… Vice-spacer
22 ……………………… 2 ……………………… 02055 ……………………… Bolt
23 ……………………… 1 ……………………… 17052 ……………………… Brine valve connector
25 ……………………… 1 ……………………… 66126 ……………………… Bypass piston assembly
26 ……………………… 1 ……………………… 56115 ……………………… Piston retainer
27 ……………………… 1 ……………………… 27504-1 …………………… Vice-piston
28 ……………………… 1 ……………………… 27503 ……………………… Bypass spacer
29 ……………………… 1 ……………………… 19040 ……………………… Spacer
30 ……………………… 1 ……………………… 27502 ……………………… Spacer
31 ……………………… 2 ……………………… 02082 ……………………… Bolt

※For more options

27
 Valve Body Assembly

F21

Filter

No Hard Water

28
 Valve Body Assembly

F21

Item No. Quantity Part No. Description

1 ……………………… 1 ……………………… 19040 ……………………… S pacer
2 ……………………… 1 ……………………… 28554-1 …………………… P iston rod
3 ……………………… 1 ……………………… 66121 ……………………… E nd-plug assembly
4 ……………………… 1 ……………………… 28552-1 …………………… P iston
5 ……………………… 6 ……………………… 28555 ……………………… Spacer
6 ……………………… 6 ……………………… 28530 ……………………… Seal
7 ……………………… 1 ……………………… 28550 ……………………… Valve body
※ 8 ……………………… 1 …………………………………………………………… DLFC
9 ……………………… 1 ……………………… 28556 ……………………… Drain connector
10 ……………………… 1 ……………………… 17052 ……………………… Brine valve connector
※ 11 ……………………… 1 …………………………………………………………… Nozzle
12 ……………………… 2 ……………………… 02051 ……………………… Bolt
13 ……………………… 1 ……………………… 17056 ……………………… Injector cover
14 ……………………… 1 ……………………… 17031 ……………………… I njector cover gasket
15 ……………………… 1 ……………………… 17059 ……………………… I njector screen
16 ……………………… 1 ……………………… 17051 ……………………… Injector
※ 17 ……………………… 1 …………………………………………………………… Throat
18 ……………………… 2 ……………………… 02053 ……………………… Bolt
19 ……………………… 1 ……………………… 17003 ……………………… Air disperser
20 ……………………… 1 ……………………… 17030 ……………………… Injector body gasket
21 ……………………… 1 ……………………… 28531 ……………………… S eal
22 ……………………… 1 ……………………… 28551 ……………………… Adapter base
23 ……………………… 1 ……………………… 01104 ……………………… O-ring
24 ……………………… 1 ……………………… 01012 ……………………… O-ring
25 ……………………… 2 ……………………… 02082 ……………………… Bolt
26 ……………………… 1 ……………………… 28557-1 …………………… Filter piston
27 ……………………… 1 ……………………… 66123 ……………………… No hard water bypass piston assy

※For more options

29
 Valve Body Assembly

F31

Hard Water

30
 Valve Body Assembly

F31

Item No. Quantity Part No . Description

1 ……………………… 2 ……………………… 02051 ……………………… s crew
2 ……………………… 1 ……………………… 17056 ……………………… Injector cover
3 ……………………… 1 ……………………… 17031 ……………………… Injector cover gasket
4 ……………………… 1 ……………………… 17059 ……………………… Screen
※ 5 ……………………… 1 …………………………………………………………… Nozzle
6 ……………………… 1 ……………………… 17051 ……………………… Injector
※ 7 ……………………… 1 …………………………………………………………… Throat
8 ……………………… 1 ……………………… 17003 ……………………… Air disperser
9 ……………………… 1 ……………………… 17030 ……………………… Injector body gasket
10 ……………………… 1 ……………………… 29503-1 …………………… Vice-valve body
※ 11 ……………………… 1 …………………………………………………………… DLFC
12 ……………………… 1 ……………………… 29502 ……………………… Coupling
13 ……………………… 1 ……………………… 29511 ……………………… Drainage connector
14 ……………………… 1 ……………………… 01025 ……………………… O-ring
15 ……………………… 1 ……………………… 01024 ……………………… O-ring
16 ……………………… 1 ……………………… 29501 ……………………… Valve body
17 ……………………… 1 ……………………… 01012 ……………………… O-ring
18 ……………………… 1 ……………………… 01104 ……………………… O-ring
19 ……………………… 1 ……………………… J 1007 ……………………… Piston assembly
20 ……………………… 1 ……………………… 66127 ……………………… End plug
21 ……………………… 4 ……………………… 29560 ……………………… Seal
22 ……………………… 2 ……………………… 29533 ……………………… Spacer
23 ……………………… 1 ……………………… 29532 ……………………… Spacer
24 ……………………… 1 ……………………… 29508-1 …………………… Vice piston rod
25 ……………………… 1 ……………………… 66125 ……………………… Vice end-plug assembly
26 ……………………… 1 ……………………… 29507-1 …………………… Vice piston
27 ……………………… 6 ……………………… 29561 ……………………… Seal
28 ……………………… 5 ……………………… 29535 ……………………… Spacer
29 ……………………… 2 ……………………… 02055 ……………………… Bolt
30 ……………………… 1 ……………………… 29504 ……………………… Cap
31 ……………………… 1 ……………………… 17052 ……………………… Brine valve connector
32 ……………………… 1 ……………………… J1008 ……………………… Piston assembly

※For more options

31
 Valve Body Assembly

F41

No Hard Water

Filter

32
 Valve Body Assembly

F41

Item No. Quantity Part No. Description

1 ……………………… 1 ……………………… 66129 ……………………… End plug assembly
2 ……………………… 1 ……………………… K1008 ……………………… Piston assembly
3 ……………………… 8 ……………………… 29560 ……………………… Seal
4 ……………………… 5 ……………………… 29533 ……………………… Spacer
5 ……………………… 2 ……………………… 31542 ……………………… Spacer, narrow
6 ……………………… 2 ……………………… 02057 ……………………… Screw
7 ……………………… 1 ……………………… 31501-1 …………………… Valve body
8 ……………………… 1 ……………………… 00108 ……………………… Straight pin
9 ……………………… 1 ……………………… 28531 ……………………… Seal
10 ……………………… 1 ……………………… 31502 ……………………… Adapter
11 ……………………… 1 ……………………… 01012 ……………………… O - ring
12 ……………………… 1 ……………………… 01033 ……………………… O - ring
13 ……………………… 4 ……………………… 02002 ……………………… Screw
14 ……………………… 2 ……………………… 31506 ……………………… Cover
15 ……………………… 2 ……………………… 01031 ……………………… O - ring
16 ……………………… 2 ……………………… 31509 ……………………… Nut
17 ……………………… 1 ……………………… K1007 ……………………… No hard water piston assembly

33
 Valve Body Assembly

F61

Hard Water

34
 Valve Body Assembly

F61

Item No. Quantity Part No . Description

1 ……………………… 1 ……………………… 66129 ……………………… E nd plug assembly
2 ……………………… 1 ……………………… K1008 ……………………… P iston assembly
3 ……………………… 8 ……………………… 29560 ……………………… Seal
4 ……………………… 5 ……………………… 29533 ……………………… S pacer
5 ……………………… 2 ……………………… 31542 ……………………… S pacer,narrow
6 ……………………… 2 ……………………… 02057 ……………………… Screw
7 ……………………… 1 ……………………… 31501-1 …………………… Valve body
8 ……………………… 1 ……………………… 66130 ……………………… Coupling assembly
9 ……………………… 1 ……………………… 39506 ……………………… Slug
10 ……………………… 1 ……………………… 28531 ……………………… S eal
11 ……………………… 1 ……………………… 39501-1 …………………… Valve body
12 ……………………… 12 ……………………… 02059 ……………………… Bolt
13 ……………………… 1 ……………………… 01042 ……………………… O -ring
14 ……………………… 1 ……………………… 01037 ……………………… O -ring
15 ……………………… 2 ……………………… 39504 ……………………… Flange segment
16 ……………………… 1 ……………………… 01036 ……………………… O -ring
17 ……………………… 1 ……………………… 39503-1 …………………… Flange ring
18 ……………………… 12 ……………………… 04007 ……………………… Washer
19 ……………………… 12 ……………………… 03005 ……………………… Nut
20 ……………………… 4 ……………………… 39560 ……………………… Seal
21 ……………………… 2 ……………………… 39531 ……………………… Spacer
22 ……………………… 1 ……………………… 39530 ……………………… Spacer
23 ……………………… 1 ……………………… 66131 ……………………… End plug assembly
24 ……………………… 1 ……………………… T1001 ……………………… Piston assembly
25 ……………………… 1 ……………………… T1005 ……………………… Piston assembly

35
 Brine System Assembly

1600 series brine system assembly

Item No. Quantity Part No. Description

1 ……………………… 1 ……………………… 04053 ……………………… Retaining ring
2 ……………………… 1 ……………………… 16080 ……………………… Spring
3 ……………………… 1 ……………………… 66122 ……………………… Brine stem assembly
4 ……………………… 1 ……………………… 16053 ……………………… Stem guide
5 ……………………… 1 ……………………… 56061 ……………………… B.L.F.C Fitting Nut
6 ……………………… 1 ……………………… 56023 ……………………… B.L.F.C Ferrule
7 ……………………… 1 ……………………… 56062 ……………………… B.L.F.C Tube Insert
8 ……………………… 1 ……………………… 56060 ……………………… Screen,Brine Line
9 ……………………… 1 ……………………… 16051 ……………………… Brine valve body
10 ……………………… 1 ……………………… 01004 ……………………… O-ring
11 ……………………… 1 ……………………… 16054 ……………………… End plug, brine valve
※ 12 ……………………… 1 ……………………………………………………………… BLFC button
13 ……………………… 1 ……………………… 56015 ……………………… Brine dispenser
14 ……………………… 1 ……………………… 16050 ……………………… Fitting, Elbow
15 ……………………… 1 ……………………… 66124 ……………………… Brine tube
16 ……………………… 1 ……………………… 17056 ……………………… Injector cover
17 ……………………… 2 ……………………… 02060 ……………………… Screw
18 ……………………… 1 ……………………… 17031 ……………………… Injector cover gasket
※ 19 ……………………… 1 ……………………………………………………………… Injector nozzle
※ 20 ……………………… 1 ……………………………………………………………… Injector throat
21 ……………………… 1 ……………………… 56059 ……………………… Screen
22 ……………………… 1 ……………………… 16001 ……………………… Injector body
23 ……………………… 1 ……………………… 17030 ……………………… Injector body gasket

※For more options

36
 Brine System Assembly
1700 series brine system assembly

Item No. Quantity Part No. Description

1 ……………………… 1 ……………………… 66164 ……………………… brine valve cap assembly
2 ……………………… 1 ……………………… 04052 ……………………… Retaining ring
3 ……………………… 1 ……………………… 04003 ……………………… Washer
4 ……………………… 1 ……………………… 17058 ……………………… Spring
5 ……………………… 1 ……………………… 66128 ……………………… Brine stem assembly
6 ……………………… 1 ……………………… 66175 ……………………… B.L.F.C Fitting Nut
7 ……………………… 1 ……………………… 17061 ……………………… B.L.F.C Tube Insert
8 ……………………… 1 ……………………… 17053 ……………………… Brine valve body
9 ……………………… 1 ……………………… 01081 ……………………… O-ring
10 ……………………… 1 ……………………… 17055 ……………………… End plug, brine valve
※ 11 ……………………… 1 ……………………………………………………………… BLFC button
12 ……………………… 1 ……………………… 17052 ……………………… Fitting, Elbow
13 ……………………… 1 ……………………… 66160 ……………………… Brine tube
※ 14 ……………………… 1 ……………………………………………………………… Injector nozzle
15 ……………………… 1 ……………………… 17031 ……………………… Injector cover gasket
16 ……………………… 1 ……………………… 17056 ……………………… Injector cover
17 ……………………… 2 ……………………… 02051 ……………………… Screw
18 ……………………… 1 ……………………… 17059 ……………………… Screen
19 ……………………… 1 ……………………… 17051 ……………………… Injector body
※ 20 ……………………… 1 ……………………………………………………………… Injector throat
21 ……………………… 1 ……………………… 17030 ……………………… Injector body gasket
※For more options

37
 Brine System Assembly

1800 series brine system assembly

Item No. Quantity Part No. Description

1 ……………………… 1 ……………………… 66161 ……………………… Brine tube
2 ……………………… 2 ……………………… 31513 ……………………… Tube fitting
3 ……………………… 6 ……………………… 02002 ……………………… Screw
4 ……………………… 1 ……………………… 18058 ……………………… Injector cover
5 ……………………… 2 ……………………… 01030 ……………………… O-ring
※ 6 ……………………… 1 ……………………………………………………………… Injector nozzle
7 ……………………… 1 ……………………… 18056 ……………………… Injector body
8 ……………………… 2 ……………………… 02011 ……………………… Screw
※ 9 ……………………… 1 ……………………………………………………………… Injector throat
10 ……………………… 1 ……………………… 31509 ……………………… Nut
11 ……………………… 1 ……………………… 31506 ……………………… Cover
12 ……………………… 1 ……………………… 01031 ……………………… O-ring
13 ……………………… 1 ……………………… K1006 ……………………… Brine stem assembly
14 ……………………… 1 ……………………… 18057 ……………………… Brine valve body
15 ……………………… 1 ……………………… 18051 ……………………… Spring
16 ……………………… 1 ……………………… 04056 ……………………… Retaining ring
17 ……………………… 1 ……………………… 66163 ……………………… Stem guide assembly
※ 18 ……………………… 1 ……………………………………………………………… BLFC button
19 ……………………… 1 ……………………… 18059 ……………………… Brine fitting

※For more options

38
 Meter Assembly

1'' meter assembly

Item No. Quantity Part No. Description

1 ……………………… 1 ……………………… 12003 ……………………… S crew
2 ……………………… 1 ……………………… 12002 ……………………… T ube
3 ……………………… 1 ……………………… 01031 ……………………… O -ring
4 ……………………… 1 ……………………… 56013 ……………………… Flow straightener
5 ……………………… 1 ……………………… 12001 ……………………… Body
6 ……………………… 1 ……………………… 12101 ……………………… Impeller spindle
7 ……………………… 1 ……………………… 12204A …………………… Impeller assembly
8 ……………………… 1 ……………………… 01014 ……………………… O-ring
9 ……………………… 1 ……………………… 1220D ……………………… Meter cover assembly
10 ……………………… 4 ……………………… 02082 ……………………… S crew

39
 Meter Assembly

1.5'' meter assembly

Item No. Quantity Part No. Description

1 ……………………… 1 ……………………… 12122 ……………………… S crew
2 ……………………… 1 ……………………… 12121 ……………………… T ube
3 ……………………… 1 ……………………… 01008 ……………………… O -ring
4 ……………………… 1 ……………………… 17004 ……………………… Flow straightener
5 ……………………… 1 ……………………… 12120 ……………………… Body
6 ……………………… 1 ……………………… 12101 ……………………… Impeller spindle
7 ……………………… 1 ……………………… 12204A …………………… Impeller assembly
8 ……………………… 1 ……………………… 01014 ……………………… O-ring
9 ……………………… 1 ……………………… 1220D ……………………… Meter cover assembly
10 ……………………… 4 ……………………… 02082 ……………………… S crew

40
 Meter Assembly

2'' meter assembly

Item No. Quantity Part No. Description

1 ……………………… 1 ……………………… 12303 ……………………… S crew
2 ……………………… 1 ……………………… 12302 ……………………… T ube
3 ……………………… 1 ……………………… 01032 ……………………… O -ring
4 ……………………… 1 ……………………… 12330 ……………………… Flow straightener
5 ……………………… 1 ……………………… 12301 ……………………… Body
6 ……………………… 1 ……………………… 12101 ……………………… Impeller spindle
7 ……………………… 1 ……………………… 12331 ……………………… Impeller assembly
8 ……………………… 1 ……………………… 01014 ……………………… O-ring
9 ……………………… 1 ……………………… 1220D ……………………… Meter cover assembly
10 ……………………… 4 ……………………… 02082 ……………………… S crew

41
 Meter Assembly

3'' meter assembly

Item No. Quantity Part No. Description

1 ……………………… 8 ……………………… 02058 ……………………… S crew
2 ……………………… 2 ……………………… 12402 ……………………… C onnecting flange
3 ……………………… 3 ……………………… 01041 ……………………… O-ring
4 ……………………… 8 ……………………… 03006 ……………………… S crew
5 ……………………… 1 ……………………… 12401 ……………………… Body
6 ……………………… 1 ……………………… 12404 ……………………… Flow straightener
7 ……………………… 6 ……………………… 02106 ……………………… Screw
8 ……………………… 1 ……………………… 1220C-E …………………… Meter cover assembly
9 ……………………… 1 ……………………… 12405 ……………………… Impeller assembly
10 ……………………… 1 ……………………… 12408 ……………………… Impeller spindle

42
 Wiring Diagram

F15/21

Timer,meter delay control valve

Meter Imm. control valve

TM - Time Motor
VDM - Valve Drive Motor

SW1- Timer Homing Switch

SW2- Timer Program Switch
SW3- Valve Homing Switch
SW4- Valve Step Switch

TPCAM- Timer Program Cam

THCAM- Timer Homing Cam
SCAM- Valve Step Cam
HCAM- Valve Homing Cam

43
 Wiring Diagram

F31

Timer,meter delay control valve

Meter Imm. control valve

TM - Time Motor
VDM - Valve Drive Motor
LDM - Lower Drive Motor

SW1-Timer Homing Switch

SW2-Timer Program Switch
SW3-Valve Homing Switch
SW4-Valve Step Switch
SW5-Brine Cam Switch
SW6-Lower Drive Switch

TPCAM- Timer Program Cam

THCAM-Timer Homing Cam
SCAM-Valve Step Cam
BVCAM - Brine Valve Cam
LD CAM- Lower Drive Cam

44
 Wiring Diagram

F41

Timer,meter delay control valve

Meter Imm. control valve

TM - Time Motor
VDM - Valve Drive Motor

SW1- Timer Homing Switch

SW2-Timer Program Switch
SW3- Valve Homing Switch
SW4- Valve Step Switch

TPCAM- Timer Program Cam

THCAM- Timer Homing Cam
SCAM- Valve Step Cam
HCAM- Valve Homing Cam

45
 Wiring Diagram

F61

Timer,meter delay control valve

Meter Imm. control valve

TM - Time Motor
VDM - Valve Drive Motor
LDM - Lower Drive Motor

SW1- Timer Homing Switch

SW2-Timer Program Switch
SW3- Valve Homing Switch
SW4- Valve Step Switch
SW5-Brine Cam Switch
SW6-Lower Drive Switch

TPCAM- Timer Program Cam

THCAM- Timer Homing Cam
SCAM- Valve Step Cam
BVCAM - Brine Valve Cam
HCAM- Valve Homing Cam

46
 Trouble Shooting

Problem Cause Correction

A. Disconnected meter cable. A. Reconnect the meter cable.
1. The control fails to B. Transformer damaged. B. Replace the transformer.
Regenerate automatically C. Electronic controller or sensor C. Replace or repair.
damaged.
2. Regeneration at wrong A. Timer improperly set, due to
A. Reset timer.
Time power failure.
A. reset unit to the new capacity.
A. Increased raw water hardness B. Keep brine tank full of salt at all times. Clean it
B. Brine concentration or yearly. Salt may be bridged. If using a salt grid
quantity. Plate insure refill water is over it.
C. Consolidate the rinse tank , clean the rinse and
C. Rinse fouling.
prevent future fouling..
D. Poor distribution, channeling
3. loss of capacity D. check distributors and back wash flow
(Uneven bed ser vice). E. Replace the spacer, seal or piston
E. Internal control leak . F. Check for resin oxidation caused by Chlorine.
F. Ageing of rinse. Mushy resin.
G. Loss of rinse. G. check for correct bed depth. Broken
distributors. Air or gas in bed: Well gas
Eliminator loose brine line.

A. Check items listed in 3. B. Close the bypass

4. Poor water quality B. Bypass is open. C. Check for too slow or high ser vice
C. Channeling. flow.
A. High salt setting. A. adjust salt setting
5. Excessive salt use
B Excessive water in brine tank . B. refer to problem 7 tank .

A. Fouling of inlet pipe. A. Clean or replace the pipe line

6.Loss of water pressure B. Fouled resin. B. Clean the resin. Pretreat to prevent.
C. Improper backwash. C. Too many resin fines. Reset the flow
Rate and time of back wash.
A. Plugged drain line. A. Check drain line and clean flow control
B. Brine valve plugged or B. Clean or replace the brine valve
7. excessive water in brine
damaged. C. Clean injector, replace injector screen
tank
C. Injector plugged. D. Increase water pressure to allow
D. Low inlet water pressure. Injector to perform properly.

A. Plugged drain line. A. Clean drain line and flow control

B. Plugged injector. B. Clean or replace the injector and screen
C. No water in the brine tank . C. Check for restriction in BLFC. Ensure
8. Softener fails to brine
D. Low water pressure. Safety float is not stuck .
Draw
E. Brine line injects air during D. Increase water pressure
brine draw. E. Check brine line for air leaks.
F. Internal control leak . F. check seal, spacer and piston for
scratches and dents.

9.Control cycles continuously A. Faulty timer. A. Replace timer

A. Foreign material in the control A. call dealer. Clean valve, rebuild

10. continuous flow to drain B. Internal control leak . unit
C. Piston jammed in brine or back B. same as above
wash position. C. same as above

47
NOTES
NOTES