FREE SHIPPING FOR ONLINE ORDERS. Terms and conditions apply.

General  >  Technology > Motor Sizing

Motor Sizing Motor Sizing Tools

Proper sizing and selection of a motor for your equipment is key to ensuring performance, reliability and Online Sizing Tools
cost of the equipment. In addition to the information below for properly sizing a motor, Oriental Motor
offers online motor sizing tools as well as assistance from our Technical Support staff.
Our Technical Support Staff is available to assist you in properly sizing and selecting your motor based
on your individual application. Simply call 1-800-GO-VEXTA (468-3982) (M-F 7:30am CST to 5:00pm
PST).

Selection Procedure
The first step is to determine the drive mechanism for your equipment. Some examples are direct
rotation, a ball screw, a belt and pulley or a rack and pinion. Along with the type of drive mechanism, you  
must also determine the dimensions, mass and friction coefficient, etc. that are required for the load
calculation: Motor Sizing Tools

Dimensions and mass (or density) of load

Dimensions and mass (or density) of each part
Friction coefficient of the sliding surface of each moving part

Next you will need to determine the required specifications for the equipment:
Operating speed and operating time
Positioning distance and positioning time
Resolution
Stopping accuracy
Position holding
Power supply and voltage
Operating environment
Specific features and requirements such as; Open-Loop, Closed-Loop, Programmable, Feedback, IP
rating, Agent approvals, etc.

In order to determine the performance you'll need from the motor, there are three factors to calculate;
Moment of Inertia, Torque and Speed. (Refer to the below sections on calculations for each.)
Once you've calculated the inertia, torque and speed for the motor you'll select the type of motor based
on the required specifications. Oriental Motor offers a wide range of stepper motors, servo motors, AC
motors and brushless motors to meet the specific needs of your equipment.
Finally, after selecting the motor type you'll make a final determination of the motor by confirming the
specifications of the selected motor (and gearhead if applicable) satisfy all of the requirements, such as
mechanical strength, acceleration time and acceleration torque.

Motor Sizing Calculations

There are three factors to calculate when sizing a motor; Moment of Inertia, Torque, and Speed.

Moment of Inertia
Moment of inertia is the measure of an object's resistance to changes in its rotation rate.
When an object is just sitting without any motion, the moment of inertia is 0.
When you try to make it move that mean you want to change the speed of the object from 0 to any, there
will be moment of inertia effect.
Fundamental Inertia (J) Equation:
  

Moment of Inertia Calculation for a Rotating Object

Moment of Inertia Calculation for a Cylinder

Moment of Inertia Calculation for a Hollow Cylinder

Moment of Inertia Calculation for an Off-Center Axis  

Moment of Inertia Calculation for a Rectangular Pillar

Moment of Inertia Calculation for an Object in Linear Motion

Units of Measure for Moment Inertia

The units of inertia are commonly used in two ways, oz-in² and oz-in-sec². The former includes gravity,
the latter only mass.
Theoretically, inertia is factor of mass so it should not include gravity, however, practically we can not
easily measure mass on the earth.
Oriental Motor commonly provides inertia in oz-in². Then, when we calculate the Acceleration Torque in
Torque Calculation we divide the total the total inertia by the gravity from.
Gravity = 386 in/sec²
oz-in² = Inertia based on weight
oz-in-sec² = inertia based on mass

Calculation for oz-in² to oz-in-sec²

Torque
Torque is the tendency of a force to rotate an object about an axis. Torque is made up of two
components; a load (constant) component and an acceleration component.
The load torque component is usually due to friction and/or gravity and is always acting on the motor.
This component can usually be determined by calculation or by putting a torque wrench on the system
and reading the torque value. When it is not able to measure, then we use some equations to calculate
the approximate value.
The acceleration torque however, is only acting on the motor when it is accelerating or decelerating.
Once the motor is running at a constant speed, this component goes away. Measuring the acceleration
component is difficult not to mention dangerous. If you want the load to be up to speed within 50
milliseconds, it’s likely that a torque wrench will fly off. Therefore, we calculate the acceleration
Sit S h
 Site Search…
component. This component is a function of the inertia of the system and the acceleration rate. So, once  
we determine these values, we can figure out the acceleration torque.
Load Torque ( T )
   
Load torque is very simple.
Product Solutions
As you see this Technical
equation torque Motor
is the product of theDownloads Virtual
force and the distance betweenContact
the force and the
nformation Information Sizing Showroom Us
center of rotation. For example, if you want to hold the force acting on the end of pulley, T = F x r. So
calculating load torque is determine the force in the system and the logical distance between the motor
αSTEP
shaft and Stepper
the where the force Motors
is acting. Brushless DC Motors Servo Motors AC Gear Motors

When the mechanics become complicated, we need to convert the F and r to fit the mechanics.

Load Torque - Actual Measurement

If you can measure the force, that is the most accurate way to find the force since it takes care of the all
efficiency and coefficient of frictions on the every part.
FB = Force when the main shaft begins to rotate

Forces
There are three types of forces; vertical, horizontal and incline. A force varies depending how it acts.
Vertical Force Calculation

Horizontal Force Calculation

  

Incline Force Calculation

Load Torque Calculation - Ball Screw Drive

Load Torque Calculation - Pulley Drive

Load Torque Calculation - Wire or Belt Drive, Rack and Pinion Drive
  

Acceleration Torque
As mentioned previously, acceleration torque is made up of inertia and acceleration rate. If we know
those two values, we can calculate the acceleration torque.

Calculate the Acceleration Torque ( Ta )

If the motor speed is varied, the acceleration torque or deceleration torque must always be set.
The basic formula is the same for all motors. However, use the formulas below when calculating the
acceleration torque for stepper or servo motors on the basis of pulse speed.
Common Formula for All Motors

When calculating the Acceleration Torque for Stepper or Servo Motors on the basis of pulse
speed
There are two basic motion profiles. Acceleration/deceleration operation is the most common. When
operating speed is low and load inertia is small, start/stop operation can be used.
  

Calculation for Required Torque ( TM )

The required torque is calculated by multiplying the sum of load torque and acceleration torque by the
safety factor.

Calculation for the Effective Load Torque ( Trms ) for Servo Motors and BX Series Brushless
Motors
When the required torque for the motor varies over time, determine if the motor can be used by
calculating the effective load torque. The effective load torque becomes particularly important for
operating patterns such as fast-cycle operations where acceleration/deceleration is frequent. Calculate
the effective load torque when selecting servo motors or the BX Series brushless motors.
  

Speed
Speed is determined by calculating the distance divided by time. For stepper or servo motors,
acceleration time must also be accounted for.
Standard Speed Calculation
Speed = Distance / Time
For Stepper or Servo Motors
Speed = Distance / (Time - Acceleration Time ( t1 )

Want to learn more?

Oriental Motor's Technical Support Team and Application Engineers will work with you to determine the
best solution for your application. ORIENTAL MOTOR's experienced team members know the
technology inside and out. We'll find the right solution based on your needs and explain the alternatives.
Call 1-800-GO-VEXTA (468-3982) to speak with an Oriental Motor Technical Support Team Member.
 
 

ABOUT ORIENTAL PRODUCT INFO SUPPORT NEWS WEB

MOTOR
Product Lead Time Product & Technology Newsletter Privacy Policy
Careers Videos
Safety Standards Press Releases Terms of Access
Manufacturing Service & Support
Warranty / Scope of Events Free Shipping Offer
ISO9001 / ISO14001 Application Product Forum

Environmental Efforts Service Life Distributor Portal

Terms & Conditions  

©2022 - ORIENTAL MOTOR USA CORP. - All Rights Reserved