Easy Duct Master Catalog

EASY DUCT ™
MASTER CATALOG
THE EASY DUCT

ADVANTAGE
• Simple to install - No special tools or training required
• Clamp-together components can be taken apart

and reused
• Flexible - Easily connects to existing ductwork
• Components and adapters fit every system
• Adjustable duct fittings simplify connections
• Smooth interior surface helps prevent clogs

EASY DUCT - MASTER CATALOG
™
EASY DUCT - AN INVESTMENT

IN YOUR FUTURE
LOWER COST THAN CONVENTIONAL JOINING METHODS
Easy Duct clamp-together ducting eliminates rivets, screws, welds and other time-consuming and costly
™
joining methods. The Easy Duct adjustable nipple also telescopes in length to eliminate the need for precise
measurements and wasted parts due to improper measuring. Thanks to the patented Easy Duct design,
straight piping, elbows and branch pieces clamp easily together in seconds and can be put together and taken
apart with no special tools. That means you don’t have to throw away your existing ducting each time you
make a floor plan change.
LASER WELDED
• Smooth. No hang up interiors and virtually seamless exterior finish that allows fewer bug harbors and
snag opportunities
• Stronger, air-tight longitudinal seams
• Rounder circumferences for easier clamping and tighter adjustable nipple seals
QUICK AND STRONG ASSEMBLY

The Easy Duct system begins with pipes and fittings (i.e. branches, elbows, pipes, hoods, and adapters from
3” to 24” in diameter) that have been machined so that each connecting end has double-rolled edges. When
the Easy Duct clamp (complete with built-in gasket) is snapped into place, the resulting seal is strong and tight
enough for almost all dust collection and solid materials conveying applications.
• Galvanized or stainless steel
• No welds - No rivets - No screws - No precise measurements required
• Your employees can handle many installations themselves
• Perfect for new installations or changes to existing systems
• Handles dusts, chemicals, food, fumes and more
• Clean outs and replacements are a snap
• Easy to take apart and reuse
DECREASED DOWNTIME
Thanks to the Easy Duct clamp together design, installations, clean outs and changes take only a fraction of
the time it takes for traditional ducting. That means reduced down-time for your operations.
EFFECTIVE FOR NEW INSTALLATIONS

AND EXISTING SYSTEMS
Many of the largest manufacturing facilities being built in the US today go online with complete Easy Duct
systems. Easy Duct also connects easily to existing ducting systems. Because Easy Duct can be taken apart
and reused, it quickly accommodates floor plan changes and machine replacements.
VERSATILE APPLICATIONS
A partial listing of materials collected or conveyed through Easy Duct includes: sawdust, metal grindings,
printing powder, plastic pellets, dry cement, carbon black, smoke, fumes, grains, lime, wood chips, mists,
toner dusts, paper trim, cocoa, and hundreds of others.
Call for a FREE analysis of how Easy Duct can cut your overall ducting and downtime costs.
i Donaldson Torit
™
TABLE OF CONTENTS
DESCRIPTION PART # PAGE DESCRIPTION PART # PAGE
Machine Adapter 3249 7 Pipe Hanger 3265 22
Flange Adapter 3250 8 HANGERS HJ Pipe Hanger 3265HJ 22
ADAPTERS
Hose Adapter 3282 8 Gripple Hanger 3265 22
Bell Mouth Adapter 3251 8 Suction Hood (Rectangle) 3230 16
ADJUSTABLE NIPPLE W/ O-RING 3202 2 Suction Hood (Round) 3230 16
ANGLE FLANGE 3261 23 HOODS Router Hood 3231 17
BALL JOINT 3209 20 Router Hood w/Magnet 3232 17
Manual 3240 13 Radial Arm Saw Hood 3229 17
BLAST NFMES 3241 13 Rubber 3280 6

GATES Auto (1-Cylinder) 3245 14 HOSES Rigid Flex Steel 3281 6
Auto (2-Cylinder) 3245 14 Ultra Flex Steel 3283 6
Branch 3220 9 IN-CUT 3223 11
Y-Branch 3221 9 IN-LINE BACK DRAFT DAMPER 3219 19
BRANCHES
Double Branch 3226 10 NO-LOSS STACKHEAD 3204 21
T-Branch 3227 10 OIL MIST GASKET 3190 24
Hose Clamp 3285 18 Nitrile Rubber O-Ring 3191 24
CLAMPS O-RINGS
Clamp w/ Pin 3260 2 O-Ring 3262 22
Standard Radius 3210 3 REDUCER 3222 12
Long Radius 3210 3 Easy Duct Pipe 3200 1
PIPES
ELBOWS Flanged 3211 4 Flanged Pipe 3201 1
Tubed 3214 5 SILENCER 3106 7
Tubed Long Radius 3214 5 TAP-IN 3224 11
End Cap 3151 12 Diverter Valve (Manual) 3235 15
END CAPS
End Cap w/ Screen 3152 12 Diverter Valve (Automatic) 3236 15
VALVES
FLOOR SWEEP 3248 17 Butterfly Valve 3208 18
Bleed-In Valve 3207 21
VIBRATION ISOLATOR 3206 20
VIEWING SPOOL 3205 19
PRODUCT DIAMETER
CODE INCHES MATERIAL SPECIAL USE
3 2 1 0-0 7 9 0 - 1 0 7 0 0 0
DEGREE CL RADIUS
ADDITIONAL INFORMATION PAGE
MATERIAL AVAILABLE
1: GALVANIZED
2: 304 STAINLESS STEEL
3: 316 STAINLESS STEEL
CUSTOM MANIFOLD 16
2SS: STAINLESS
CONDITIONS OF SALE 28
6SS: ALUMINUM
INSTALLING ADJUSTABLE NIPPLE 25

SIZING BRANCHES 26
PRODUCT PHOTOGRAPHS REFERENCE ONLY GENERAL CONDITIONS OF SALES APPLY

SIZING AN EASY DUCT SYSTEM 27
donaldsontorit.com | 800-365-1331 ii
™
EASY DUCT PIPE & FLANGED PIPE
PIPE FLANGED PIPE

PT. 3200 PT. 3201
Laser Welded Seam with Rolled Ends. 3” is Lock Formed. Use this duct system for sizes above 24”. Longitudinal lock form
Connects quickly and easily with the QF clamp. seam, with Van Stone Angle Flange on both ends
“d
“L”
↑
“D”
↓ “D”
← “L” → Van Stone

Connection
DIAMETER PART GAUGE LENGTH DIAMETER PART GAUGE LENGTH

ROLL d
D (in) NO.* GALV. SS L (in) D (in) NO.* GALV. SS L (in)
3 3200-0300 22 22 0.2 59.25 3 3201-03LW 22 22 59

4 3200-0400 22 22 0.2 59.25 4 3201-04LW 22 22 59
5 3200-0500 22 22 0.2 59.25 5 3201-05LW 22 22 59
6 3200-0600 22 22 0.2 59.25 6 3201-06LW 22 22 59
7 3200-0700 22 22 0.3 59.06 7 3201-07LW 22 22 59
8 3200-0800 22 22 0.3 59.06 8 3201-08LW 22 22 59
9 3200-0900 22 22 0.3 59.06 9 3201-09LW 22 22 59
10 3200-1000 22 22 0.3 58.75 10 3201-10LW 22 22 59
11 3200-1100 22 22 0.3 58.75 11 3201-11LW 22 22 59
12 3200-1200 22 22 0.4 58.75 12 3201-12LW 22 22 59
13 3200-1300 20 20 0.4 58.75 13 3201-13LW 20 20 59
14 3200-1400 20 20 0.4 58.75 14 3201-14LW 20 20 59
15 3200-1500 20 20 0.4 58.75 15 3201-15LW 20 20 59
16 3200-1600 20 20 0.4 58.75 16 3201-16LW 20 20 59
17 3200-1700 20 20 0.4 58.75 17 3201-17LW 20 20 59
18 3200-1800 20 20 0.4 58.75 18 3201-18LW 20 20 59
20 3200-2000 20 20 0.4 58.75 20 3201-20LW 20 20 59
22 3200-2200 20 20 0.4 58.75 22 3201-22LW 20 20 59
24 3200-2400 20 20 0.4 58.75 24 3201-24LW 20 20 59
26 3201-2616 16 16 59
28 3201-2816 16 16 59
* Add -100000 to part number for galvanized 30 3201-3016 16 16 59

Add -200000 to part number for stainless steel 32 3201-3216 16 16 59
34 3201-3416 16 16 59
36 3201-3616 16 16 59
38 3201-3816 16 16 59
40 3201-4016 16 16 59
ORDERING NOTES: Data is subject to change without notice. Stainless steel components requiring flanges will be supplied with SS flanges unless otherwise specified. Stainless steel components are manufactured
with 304 SS. [Call for 316 SS Prices]. For special parts or items to be custom manufactured call for quotation.
1 Donaldson Torit
™
ADJUSTABLE NIPPLE WITH O-RING

& CLAMP WITH PIN
ADJUSTABLE NIPPLE CLAMP WITH PIN
WITH O-RING PT. 3202 PT. 3260
Used to provide variable length adjustment of Easy Duct Standard clamps come with Nitrile seals to help prevent leakage over
System. Black O-Ring included. multiple uses. Clamps with ePTFE seals available at additional charge.
DIAMETER PART LENGTH GAUGE DIAMETER PART

D (in) NO.* L (in) GALV. SS (in) NO. ‡
3 3202-0300 11 1/4 22 22 3 3260-0300

4 3202-0400 11 1/4 22 22 4 3260-0400
5 3202-0500 11 1/4 22 22 5 3260-0500
6 3202-0600 11 1/4 22 22 6 3260-0600
7 3202-0700 11 1/8 22 22 7 3260-0700
8 3202-0800 11 22 22 8 3260-0800
9 3202-0900 11 22 22 9 3260-0900
10 3202-1000 10 7/8 22 22 10 3260-1000
11 3202-1100 10 5/8 22 22 11 3260-1100
12 3202-1200 10 5/8 22 22 12 3260-1200
13 3202-1300 10 5/8 20 20 13 3260-1300
14 3202-1400 10 5/8 20 20 14 3260-1400
15 3202-1500 10 5/8 20 20 15 3260-1500
16 3202-1600 10 5/8 20 20 16 3260-1600
17 3202-1700 10 5/8 20 20 17 3260-1700
18 3202-1800 10 5/8 20 20 18 3260-1800
20 3202-2000 10 5/8 20 20 20 3260-2000
22 3202-2200 10 5/8 20 20 22 3260-2200
24 3202-2400 10 5/8 20 20 24 3260-2400
ADDITIONAL PINS
LARGE BRIDGE PINS 3260-PINS-LARGE
SMALL BRIDGE PINS 3260-PINS-SMALL
ADDITIONAL NITRILE SEALS
3–6 3260-0375-SP3000
7 – 11 3260-0500-SP4000
* Add -100000 to part number for galvanized
Add -200000 to part number for stainless steel 12 – 24 3260-0650-SP5000
‡ Add -100900 for galvanized
donaldsontorit.com | 800-365-1331 2
™
ELBOW - STANDARD & LONG RADIUS

ELBOW ELBOW ELBOW LONG
PT. 3210 PT. 3210 RADIUS PT. 3210
Press Formed Segmented Segmented
“D”
“D”
“D”
“A” TANGENT
“A” TANGENT
“A” TANGENT
1.0 C.L.R.
+ C.L.R. C.L.R.
C.L.R. 1.5 C.L.R. 2.5 C.L.R.
T= Tubed style. CLR= Center Line radius. P= Press formed halves stitch welded together. S= Segmented elbows.
ELBOW - STANDARD RADIUS

DIAMETER 90° 60° 45° 30° CLR STYLE GAUGE TANGENTS (in)
D (in) PART NO. * PART NO. * PART NO. * PART NO. * GALV. SS GALV. SS GALV. SS GALV. SS
3 3210-0390-103000 3210-0360-103000 3210-0345-103000 3210-0330-103000 1.0 1.5 P T 24 14 2.25 2
4 3210-0490-104000 3210-0460-104000 3210-0445-104000 3210-0430-104000 1.0 1.5 P T 24 14 1.32 2
5 3210-0590-105000 3210-0560-105000 3210-0545-105000 3210-0530-105000 1.0 1.5 P T 24 14 1.32 2
6 3210-0690-106000 3210-0660-106000 3210-0645-106000 3210-0630-106000 1.0 1.5 P T 24 14 1.32 2
7 3210-0790-107000 3210-0760-107000 3210-0745-107000 3210-0730-107000 1.0 1.5 P S 24 22 1.32 2.25
8 3210-0890-112000 3210-0860-112000 3210-0845-112000 3210-0830-112000 1.5 1.5 S S 22 22 2.25 2.25
9 3210-0990-113500 3210-0960-113500 3210-0945-113500 3210-0930-113500 1.5 1.5 S S 22 22 2.25 2.25
10 3210-1090-115000 3210-1060-115000 3210-1045-115000 3210-1030-115000 1.5 1.5 S S 22 22 2.25 2.25
11 3210-1190-116500 3210-1160-116500 3210-1145-116500 3210-1130-116500 1.5 1.5 S S 22 22 2.25 2.25
12 3210-1290-118000 3210-1260-118000 3210-1245-118000 3210-1230-118000 1.5 1.5 S S 22 22 2.25 2.25
13 3210-1390-119500 3210-1360-119500 3210-1345-119500 3210-1330-119500 1.5 1.5 S S 20 20 2.25 2.25
14 3210-1490-121000 3210-1460-121000 3210-1445-121000 3210-1430-121000 1.5 1.5 S S 20 20 2.25 2.25
15 3210-1590-122500 3210-1560-122500 3210-1545-122500 3210-1530-122500 1.5 1.5 S S 20 20 2.25 2.25
16 3210-1690-124000 3210-1660-124000 3210-1645-124000 3210-1630-124000 1.5 1.5 S S 20 20 2.25 2.25
17 3210-1790-125500 3210-1760-125500 3210-1745-125500 3210-1730-125500 1.5 1.5 S S 20 20 2.25 2.25
18 3210-1890-127000 3210-1860-127000 3210-1845-127000 3210-1830-127000 1.5 1.5 S S 20 20 2.25 2.25
20 3210-2090-130000 3210-2060-130000 3210-2045-130000 3210-2030-130000 1.5 1.5 S S 20 20 2.25 2.25
22 3210-2290-133000 3210-2260-133000 3210-2245-133000 3210-2230-133000 1.5 1.5 S S 20 20 2.25 2.25
24 3210-2490-136000 3210-2460-136000 3210-2445-136000 3210-2430-136000 1.5 1.5 S S 20 20 2.25 2.25
ELBOW - LONG RADIUS

DIAMETER 90° 60° 45° 30° CLR STYLE GAUGE TANGENTS (in)
D (in) PART NO. * PART NO. * PART NO. * PART NO. * GALV. SS GALV. SS GALV. SS GALV. SS
3 3210-0390-104500 3210-0360-104500 3210-0345-104500 3210-0330-104500 1.5 2.5 P T 24 14 2 2
4 3210-0490-106000 3210-0460-106000 3210-0445-106000 3210-0430-106000 1.5 2.5 P T 24 14 2 2
5 3210-0590-107500 3210-0560-107500 3210-0545-107500 3210-0530-107500 1.5 2.5 P T 24 14 2 2
6 3210-0690-109000 3210-0660-109000 3210-0645-109000 3210-0630-109000 1.5 2.5 P T 24 14 2 2
7 3210-0790-110500 3210-0760-110500 3210-0745-110500 3210-0730-110500 1.5 2.5 P S 24 22 2 2.25
8 3210-0890-120000 3210-0860-120000 3210-0845-120000 3210-0830-120000 2.5 2.5 S S 22 22 2.25 2.25
9 3210-0990-122500 3210-0960-122500 3210-0945-122500 3210-0930-122500 2.5 2.5 S S 22 22 2.25 2.25
10 3210-1090-215000 3210-1060-215000 3210-1045-215000 3210-1030-215000 2.5 2.5 S S 22 22 2.25 2.25
11 3210-1190-127500 3210-1160-127500 3210-1145-127500 3210-1130-127500 2.5 2.5 S S 22 22 2.25 2.25
12 3210-1290-130000 3210-1260-130000 3210-1245-130000 3210-1230-130000 2.5 2.5 S S 22 22 2.25 2.25
13 3210-1390-132500 3210-1360-132500 3210-1345-132500 3210-1330-132500 2.5 2.5 S S 20 20 2.25 2.25
14 3210-1490-135000 3210-1460-135000 3210-1445-135000 3210-1430-135000 2.5 2.5 S S 20 20 2.25 2.25
15 3210-1590-137500 3210-1560-137500 3210-1545-137500 3210-1530-137500 2.5 2.5 S S 20 20 2.25 2.25
16 3210-1690-140000 3210-1660-140000 3210-1645-140000 3210-1630-140000 2.5 2.5 S S 20 20 2.25 2.25
17 3210-1790-142500 3210-1760-142500 3210-1745-142500 3210-1730-142500 2.5 2.5 S S 20 20 2.25 2.25
18 3210-1890-145000 3210-1860-145000 3210-1845-145000 3210-1830-145000 2.5 2.5 S S 20 20 2.25 2.25
20 3210-2090-150000 3210-2060-150000 3210-2045-150000 3210-2030-150000 2.5 2.5 S S 20 20 2.25 2.25
22 3210-2290-155000 3210-2260-155000 3210-2245-155000 3210-2230-155000 2.5 2.5 S S 20 20 2.25 2.25
24 3210-2490-160000 3210-2460-160000 3210-2445-160000 3210-2430-160000 2.5 2.5 S S 20 20 2.25 2.25
* Call 800 number for stainless steel part numbers
3 Donaldson Torit
™
ELBOW - FLANGED
ELBOW - FLANGED
PT. 3211
Elbows are supplied with a Van Stone Angle Flange on both ends.
“D”
“A” TANGENT
+ C.L.R.
1.5 C.L.R.
T= Tubed style. CLR= Center Line radius. P= Press formed halves stitch welded together. S= Segmented elbows.
DIAMETER 90° 60° 45° 30° CLR STYLE GAUGE TANGENTS

D (in) PART NO. * PART NO. * PART NO. * PART NO. * GALV. SS GALV. SS GALV. SS (in)
3 3211-0390-103000 3211-0360-103000 3211-0345-103000 3211-0330-103000 1.0 1.5 P T 24 14 2

4 3211-0490-104000 3211-0460-104000 3211-0445-104000 3211-0430-104000 1.0 1.5 P T 24 14 2
5 3211-0590-105000 3211-0560-105000 3211-0545-105000 3211-0530-105000 1.0 1.5 P T 24 14 2
6 3211-0690-106000 3211-0660-106000 3211-0645-106000 3211-0630-106000 1.0 1.5 P T 24 14 2
7 3211-0790-107000 3211-0760-107000 3211-0745-107000 3211-0730-107000 1.0 1.5 P S 24 22 2
8 3211-0890-112000 3211-0860-112000 3211-0845-112000 3211-0830-112000 1.5 1.5 S S 22 22 2
9 3211-0990-113500 3211-0960-113500 3211-0945-113500 3211-0930-113500 1.5 1.5 S S 22 22 2
10 3211-1090-115000 3211-1060-115000 3211-1045-115000 3211-1030-115000 1.5 1.5 S S 22 22 2
11 3211-1190-116500 3211-1160-116500 3211-1145-116500 3211-1130-116500 1.5 1.5 S S 22 22 2
12 3211-1290-118000 3211-1260-118000 3211-1245-118000 3211-1230-118000 1.5 1.5 S S 22 22 2
13 3211-1390-119500 3211-1360-119500 3211-1345-119500 3211-1330-119500 1.5 1.5 S S 20 20 2
14 3211-1490-121000 3211-1460-121000 3211-1445-121000 3211-1430-121000 1.5 1.5 S S 20 20 2
15 3211-1590-122500 3211-1560-122500 3211-1545-122500 3211-1530-122500 1.5 1.5 S S 20 20 2
16 3211-1690-124000 3211-1660-124000 3211-1645-124000 3211-1630-124000 1.5 1.5 S S 20 20 4
17 3211-1790-125500 3211-1760-125500 3211-1745-125500 3211-1730-125500 1.5 1.5 S S 20 20 4
18 3211-1890-127000 3211-1860-127000 3211-1845-127000 3211-1830-127000 1.5 1.5 S S 20 20 4
20 3211-2090-130000 3211-2060-130000 3211-2045-130000 3211-2030-130000 1.5 1.5 S S 20 20 4
22 3211-2290-133000 3211-2260-133000 3211-2245-133000 3211-2230-133000 1.5 1.5 S S 20 20 4
24 3211-2490-136000 3211-2460-136000 3211-2445-136000 3211-2430-136000 1.5 1.5 S S 20 20 4
26 3211-2690-139000 3211-2660-139000 3211-2645-139000 3211-2630-139000 1.5 1.5 S S 18 18 4
28 3211-2890-142000 3211-2860-142000 3211-2845-142000 3211-2830-142000 1.5 1.5 S S 18 18 4
30 3211-3090-145000 3211-3060-145000 3211-3045-145000 3211-3030-145000 1.5 1.5 S S 18 18 4
32 3211-3290-148000 3211-3260-148000 3211-3245-148000 3211-3230-148000 1.5 1.5 S S 18 18 4
34 3211-3490-151000 3211-3460-151000 3211-3445-151000 3211-3430-151000 1.5 1.5 S S 16 16 4
36 3211-3690-154000 3211-3660-154000 3211-3645-154000 3211-3630-154000 1.5 1.5 S S 16 16 4
38 3211-3890-157000 3211-3860-157000 3211-3845-157000 3211-3830-157000 1.5 1.5 S S 16 16 4
40 3211-4090-160000 3211-4060-160000 3211-4045-160000 3211-4030-160000 1.5 1.5 S S 16 16 4

™
ELBOWS - TUBED
ELBOW - TUBED ELBOW - TUBED LONG
PT. 3214 RADIUS PT. 3214
“D”
“D”
“A” TANGENT
“A” TANGENT
C.L.R. C.L.R.
1.5 C.L.R.
2.5 C.L.R.
CLR= Center Line radius.
ELBOW - TUBED
DIAMETER 90° 60° 45° 30° GAUGE TANGENTS
CLR
D (in) PART NO. * PART NO. * PART NO. * PART NO. * GALV. SS (in)
3 3214-0390-104500 3214-0360-104500 3214-0345-104500 3214-0330-104500 1.5 16 14 2
4 3214-0490-106000 3214-0460-106000 3214-0445-106000 3214-0430-106000 1.5 16 14 2
5 3214-0590-107500 3214-0560-107500 3214-0545-107500 3214-0530-107500 1.5 14 14 2
6 3214-0690-109000 3214-0660-109000 3214-0645-109000 3214-0630-109000 1.5 14 14 2
8 3214-0890-112000 3214-0860-112000 3214-0845-112000 3214-0830-112000 1.5 14 14 2
ELBOW - TUBED LONG RADIUS

DIAMETER 90° 60° 45° 30° GAUGE TANGENTS
CLR
D (in) PART NO. * PART NO. * PART NO. * PART NO. * GALV. SS (in)
3 3214-0390-107500 3214-0360-107500 3214-0345-107500 3214-0330-107500 2.5 16 14 2
4 3214-0490-110000 3214-0460-110000 3214-0445-110000 3214-0430-110000 2.5 16 14 2
5 3214-0590-112500 3214-0560-112500 3214-0545-112500 3214-0530-112500 2.5 14 14 2
6 3214-0690-115000 3214-0660-115000 3214-0645-115000 3214-0630-115000 2.5 14 14 2
8 3214-0890-120000 3214-0860-120000 3214-0845-120000 3214-0830-120000 2.5 14 22 2

5 Donaldson Torit
™
HOSES
RUBBER HOSE RIGID FLEX STEEL ULTRA FLEX
PT. 3280 HOSE PT. 3281 STEEL HOSE
Flexible rubber hose with steel coil. Flexible rigid steel hose for higher PT. 3283
Hose clamps sold separately. “Clear” temperature or abrasive material. Available in Special flex steel hose. Available
“FDA” hose is available upon request. Galvanized or Stainless Steel. in Galvanized or Stainless Steel.
Note: All hose is sold in 5’ increments with 5’ minimum purchase. Easy Duct, flanged, and raw end styles are available.
DIAMETER PART DIAMETER DIAMETER PART

PART NO.
(in) NO. (in) (in) NO.
1.0 3280-0100-000000 1.5 3281-1500-100000 3.0 3283-0300
1.5 3280-1500-000000 2.0 3281-0200-100000 4.0 3283-0400
2.0 3280-0200-000000 2.5 3281-2500-100000 5.0 3283-0500
2.5 3280-2500-000000 3.0 3281-0300-100000 6.0 3283-0600
3.0 3280-0300-000000 3.5 3281-3500-100000 7.0 3283-0700
3.5 3280-3500-000000 4.0 3281-0400-100000 8.0 3283-0800

• E nds and adapters must be welded onto steel hose as
4.0 3280-0400-000000 5.0 3281-0500-100000
standard “worm clamps” will not work
• Do not use #3285 SS Hose Clamps with this hose
5.0 3280-0500-000000 6.0 3281-0600-100000 • Sold by the foot in 5’ increments
• Add -100000 to part number for galvanized steel
5.5 3280-5500-000000 7.0 3281-0700-100000 • Add -200000 to part number for stainless steel
6.0 3280-0600-000000 8.0 3281-0800-100000
7.0 3280-0700-000000 9.0 3281-0900-100000
8.0 3280-0800-000000 10.0 3281-1000-100000
9.0 3280-0900-000000 12.0 3281-1200-100000
10.0 3280-1000-000000 14.0 3281-1400-100000

• Call 800 number for stainless steel part numbers
12.0 3280-1200-000000
• Use #3249 Machine Adapter with this hose
• Do not use #3285 SS Hose Clamps with this hose
14.0 3280-1400-000000 • Sold by the foot in 5’ increments
16.0 3280-1600-000000
18.0 3280-1800-000000
20.0 3280-2000-000000
22.0 3280-2200-000000
24.0 3280-2400-000000
• Also available in clear “FDA” upon request
• #3282 Hose Adaptor recommended with this hose
• Sold by the foot in 5’ increments
™
SILENCER & MACHINE ADAPTER

SILENCER MACHINE ADAPTER
PT. 3106 PT. 3249
Reduces sound levels from fans and equipment. Specify desired ID or OD of non Easy Duct style. Must be within
maximum opened dimension, or will be priced as a reducer.
End Styles: Easy Duct (standard), Flanged, or Raw
Expanded Raw
3” Deep
I.D. or
“A”
O.D.
I.D. “A”
5.5”
5.5”
aw
INNER OUTER RAW END APPROX. MAXIMUM

PART LENGTH DIAMETER PART
DIAMETER DIAMETER GAUGE GAUGE LENGTH OPEN DIM.
NO.* C (in) A (in) NO.* OD (in) ID (in)
A (in) B (in) (in) ID (in)
3 12 3106-0300 28 20 3 3249-0300 3.00 2.90 22 5.5 3.18

4 12 3106-0400 28 20 4 3249-0400 3.93 3.86 22 4.0 4.30
5 13 3106-0500 28 20 5 3249-0500 4.94 4.87 22 4.0 5.30
6 14 3106-0600 30 20 6 3249-0600 5.96 5.89 22 4.0 6.30
7 15 3106-0700 30 20 7 3249-0700 6.96 6.89 22 4.0 7.30
8 16 3106-0800 35 20 8 3249-0800 7.95 7.88 22 4.0 8.30
9 17 3106-0900 40 20 9 3249-0900 8.95 8.88 22 4.0 9.30
10 18 3106-1000 48 20 10 3249-1000 9.95 9.89 22 4.0 10.30
12 20 3106-1200 54 20 11 3249-1100 10.94 10.88 22 4.0 11.30
14 22 3106-1400 60 20 12 3249-1200 12.06 11.97 22 5.5 12.30
16 24 3106-1600 64 20 13 3249-1300 13.05 12.97 20 5.5 13.30
18 26 3106-1800 68 20 14 3249-1400 14.04 13.96 20 5.5 14.30
20 28 3106-2000 72 20 15 3249-1500 15.04 14.97 20 5.5 15.30
22 30 3106-2200 76 20 16 3249-1600 16.04 15.97 20 5.5 16.30
24 32 3106-2400 80 20 17 3249-1700 17.05 16.97 20 5.5 17.30
26 34 3106-2600 80 20 18 3249-1800 18.04 17.96 20 5.5 18.30
28 36 3106-2800 80 20 20 3249-2000 20.04 19.96 20 5.5 20.30
30 38 3106-3000 80 18 22 3249-2200 22.05 21.97 20 5.5 22.30
32 40 3106-3200 80 18 24 3249-2400 24.02 23.94 20 5.5 24.30
34 42 3106-3400 80 18 * Add -100000 to part number for galvanized
Add -200000 to part number for stainless steel
36 44 3106-3600 80 18
38 46 3106-3800 80 18
40 48 3106-4000 80 18
7 Donaldson Torit
™
ADAPTERS
FLANGE ADAPTER HOSE BELL MOUTH
PT. 3250 ADAPTER ADAPTER
Angle Flange Standard. For Flat Flange, PT. 3282 PT. 3251
specify the hole pattern. If no drawing is Hose adapters are available in A flared end adapter. Increases capture
provided, the flange will be blank. Galvanized or Stainless Steel. ratio of air, dust, smoke, etc. 20 gauge.
End Styles: Easy Duct (standard), Flanged, End Styles: Easy Duct (standard), End Styles: Easy Duct (standard),
or Raw Flanged, or Raw Flanged, or Raw
Hose
Bead
QF
End ← “A” →
↓ ↓
“D” ↑ ↑
“D” “L”
↓ ↓
Length ← Length → ← “B” →
APPROX. DIAMETER APPROX. DIAMETER DIAMETER LENGTH

DIAMETER PART PART PART
LENGTH GAUGE D LENGTH GAUGE A B L
D (in) NO.* NO.* NO.*
(in) (in) (in) (in) (in) (in)
3 3250-0300 5.0 22 3 3282-0300 5.5 22 3 8 3251-0300 4.5

4 3250-0400 3.5 22 4 3282-0400 4 22 4 9 3251-0400 4.5
5 3250-0500 3.5 22 5 3282-0500 4 22 5 10 3251-0500 4.5
6 3220-0600 3.5 22 6 3282-0600 4 22 6 12 3251-0600 5.0
7 3250-0700 3.5 22 7 3282-0700 4 22 7 13 3251-0700 5.0
8 3250-0800 3.5 22 8 3282-0800 4 22 8 14 3251-0800 5.0
9 3250-0900 3.5 22 9 3282-0900 4 22 9 15 3251-0900 5.0
10 3250-1000 3.5 22 10 3282-1000 4 22 10 16 3251-1000 5.0
11 3250-1100 3.5 22 11 3282-1100 4 22 11 19 3251-1100 6.0
12 3250-1200 3.5 22 12 3282-1200 4 22 12 20 3251-1200 6.0
13 3250-1300 5.0 20 13 3282-1300 5.5 20 13 21 3251-1300 6.0
14 3250-1400 5.0 20 14 3282-1400 5.5 20 14 22 3251-1400 6.0
15 3250-1500 5.0 20 15 3282-1500 5.5 20 15 23 3251-1500 6.0
16 3250-1600 5.0 20 16 3282-1600 5.5 20 16 26 3251-1600 7.0
17 3250-1700 5.0 20 17 3282-1700 5.5 20 17 27 3251-1700 7.0
18 3250-1800 5.0 20 18 3282-1800 5.5 20 18 28 3251-1800 7.0
20 3250-2000 5.0 20 20 3282-2000 5.5 20 20 30 3251-2000 7.0
22 3250-2200 5.0 20 22 3282-2200 5.5 20 22 34 3251-2200 8.0
24 3250-2400 5.0 20 24 3282-2400 5.5 20 24 36 3251-2400 8.0
™
BRANCH & Y-BRANCH

BRANCH Y- BRANCH
PT. 3220 PT. 3221
When ordering specify A, B, C. If A, B, or D is desired in flange, add price of flange and denote by FL after
End Styles: Easy Duct (standard), Flanged, or Raw dimension for which flange is needed. When ordering specify A, B, D.
30 Deg
“C” 60 Deg
“B” “B” “D”
“L ”=Bx2 +15”
Q-F ALL LEGS “L”=Bx2+9 ”
3.5”
QF=5.5” STD
FL= 8.5”
“H”=A+4”
Q-F & FL
“L” x.5
“A” “A”
Standard 30° A–B≥B–C Standard 60° B+D≥A

Optional 45° Use this formula to determine if a reducer is needed at C Optional 90° Both B & D must be at least 50% of A. With B or D being 80% of the opposite leg.
Flange Leg: Length = 4.5”
Height = A+4”
DIAMETER PART GAUGE DIAMETER PART GAUGE

A (in) NO. GALV. SS A (in) NO. GALV. SS
3 3220-03XX 22 22 3 3221-03XX 22 22
4 3220-04XX 22 22 4 3221-04XX 22 22
5 3220-05XX 22 22 5 3221-05XX 22 22
6 3220-06XX 22 22 6 3221-06XX 22 22
7 3220-07XX 22 22 7 3221-07XX 22 22
8 3220-08XX 22 22 8 3221-08XX 22 22
9 3220-09XX 22 22 9 3221-09XX 22 22
10 3220-10XX 22 22 10 3221-10XX 22 22
11 3220-11XX 22 22 11 3221-11XX 22 22
12 3220-12XX 22 22 12 3221-12XX 22 22
13 3220-13XX 20 20 13 3221-13XX 20 20
14 3220-14XX 20 20 14 3221-14XX 20 20
15 3220-15XX 20 20 15 3221-15XX 20 20
16 3220-16XX 20 20 16 3221-16XX 20 20
17 3220-17XX 20 20 17 3221-17XX 20 20
18 3220-18XX 20 20 18 3221-18XX 20 20
20 3220-20XX 20 20 20 3221-20XX 20 20
22 3220-22XX 20 20 22 3221-22XX 20 20
24 3220-24XX 20 20 24 3221-24XX 20 20
26 3220-26XX 18 18 26 3221-26XX 18 18
28 3220-28XX 18 18 28 3221-28XX 18 18
30 3220-30XX 18 18 30 3221-30XX 18 18
32 3220-32XX 18 18 32 3221-32XX 18 18
34 3220-34XX 18 18 34 3221-34XX 18 18
36 3220-36XX 18 18 36 3221-36XX 18 18
38 3220-38XX 18 18 38 3221-38XX 18 18
40 3220-40XX 18 18 40 3221-40XX 18 18
9 Donaldson Torit
™
DOUBLE BRANCH & T- BRANCH

DOUBLE BRANCH T- BRANCH
PT. 3226 PT. 3227
When ordering specify A, B, C, D. End Styles: Easy Duct (standard), Flanged, or Raw
← “B” ←
↔
90 Deg
←
“A1” “A2”
←
← “L” = “B” + 8”
←
Standard 30° (A - B) ≥ (B - C) and (B) ≥ (D) Note: “A1” to “A2” must be same dimension, however, “B” must be equal to or smaller than the
Optional 45° “A” dimension.
Note: Reducer at “B” or “D” may be required. Use formula above to determine.
DIAMETER PART GAUGE DIAMETER PART GAUGE

A (in) NO. GALV. SS A (in) NO. GALV. SS
3 3226-03XX 22 22 3 3227-03XX 22 22
4 3226-04XX 22 22 4 3227-04XX 22 22
5 3226-05XX 22 22 5 3227-05XX 22 22
6 3226-06XX 22 22 6 3227-06XX 22 22
7 3226-07XX 22 22 7 3227-07XX 22 22
8 3226-08XX 22 22 8 3227-08XX 22 22
9 3226-09XX 22 22 9 3227-09XX 22 22
10 3226-10XX 22 22 10 3227-10XX 22 22
11 3226-11XX 22 22 11 3227-11XX 22 22
12 3226-12XX 22 22 12 3227-12XX 22 22
13 3226-13XX 20 20 13 3227-13XX 20 20
14 3226-14XX 20 20 14 3227-14XX 20 20
15 3226-15XX 20 20 15 3227-15XX 20 20
16 3226-16XX 20 20 16 3227-16XX 20 20
17 3226-17XX 20 20 17 3227-17XX 20 20
18 3226-18XX 20 20 18 3227-18XX 20 20
20 3226-20XX 20 20 20 3227-20XX 20 20
22 3226-22XX 20 20 22 3227-22XX 20 20
24 3226-24XX 20 20 24 3227-24XX 20 20
26 3226-26XX 18 18 26 3227-26XX 18 18
28 3226-28XX 18 18 28 3227-28XX 18 18
30 3226-30XX 18 18 30 3227-30XX 18 18
32 3226-32XX 18 18 32 3227-32XX 18 18
34 3226-34XX 18 18 34 3227-34XX 18 18
36 3226-36XX 18 18 36 3227-36XX 18 18
38 3226-38XX 18 18 38 3227-38XX 18 18
40 3226-40XX 18 18 40 3227-40XX 18 18
™
IN-CUT & TAP-IN

IN-CUT TAP-IN
PT. 3223 PT. 3224
In-Cut is used to cut into existing lines to begin the Tap-In is used to cut into existing lines to begin the
Easy Duct system. Easy Duct system.
End Styles: Easy Duct (standard), Flanged, or Raw End Styles: Easy Duct (standard), Flanged, or Raw
←
“B”
4”
←
←
“A”
← ←
←
Saddle length + width = 3” Saddle length + width = 2” All directions from
All directions from Branch Tube (B) Branch Tube (B)
Standard 30° Standard 30°
Optional 45° Optional 45°
PIPE DIAMETER PART GAUGE PIPE DIAMETER PART GAUGE

A (in) NO.* GALV. SS A (in) NO.* GALV. SS
4 3223-04XX 22 22 4 3224-04XX 22 22
5 3223-05XX 22 22 5 3224-05XX 22 22
6 3223-06XX 22 22 6 3224-06XX 22 22
7 3223-07XX 22 22 7 3224-07XX 22 22
8 3223-08XX 22 22 8 3224-08XX 22 22
9 3223-09XX 22 22 9 3224-09XX 22 22
10 3223-10XX 22 22 10 3224-10XX 22 22
11 3223-11XX 22 22 11 3224-11XX 22 22
12 3223-12XX 22 22 12 3224-12XX 22 22
13 3223-13XX 20 20 13 3224-13XX 20 20
14 3223-14XX 20 20 14 3224-14XX 20 20
15 3223-15XX 20 20 15 3224-15XX 20 20
16 3223-16XX 20 20 16 3224-16XX 20 20
17 3223-17XX 20 20 17 3224-17XX 20 20
18 3223-18XX 20 20 18 3224-18XX 20 20
20 3223-20XX 20 20 20 3224-20XX 20 20
22 3223-22XX 20 20 22 3224-22XX 20 20
24 3223-24XX 20 20 24 3224-24XX 20 20
26 3223-26XX 18 18 26 3224-26XX 18 18
28 3223-28XX 18 18 28 3224-28XX 18 18
30 3223-30XX 18 18 30 3224-30XX 18 18
32 3223-32XX 18 18 32 3224-32XX 18 18
34 3223-34XX 18 18 34 3224-34XX 18 18
36 3223-36XX 18 18 36 3224-36XX 18 18
38 3223-38XX 18 18 38 3224-38XX 18 18
40 3223-40XX 18 18 40 3224-40XX 18 18
* XX = B dimension
11 Donaldson Torit
™
END CAPS & REDUCER

END CAP END CAP W/ REDUCER
PT. 3151 SCREEN PT. 3222
End Caps enable users to PT. 3152 Specify reducer end style.
close-off taps for future use. Used in situations where openings are needed to Specify A, B when ordering.
allow air to enter or exit a system. Screen keeps Easy Duct length (L) = A-B+6”, 7” min.
foreign objects from entering the system. FL length (L) = A-B+8”, 9” min.
Standing
⁭ Seam Standing
⁭
⁭ Seam
⁭
“D” “D” Wire
⁭
Mesh
⁭ ⁭
End
⁭
Cap
⁭
⁭
⁭
⁭
2¼” nominal
2¼” nominal
Note: “X” & “Y” are standard 2” long.
DIAMETER PART DIAMETER PART DIAMETER PART GAUGE *

GAUGE GAUGE
D (in) NO* D (in) NO* A (in) NO. GALV. SS
3 3151-0300 18 3 3152-0300 18 4 3222-04XX 22 22
4 3151-0400 22 4 3152-0400 22 5 3222-05XX 22 22
5 3151-0500 22 5 3152-0500 22 6 3222-06XX 22 22
6 3151-0600 22 6 3152-0600 22 7 3222-07XX 22 22
7 3151-0700 22 7 3152-0700 22 8 3222-08XX 22 22
8 3151-0800 22 8 3152-0800 22 9 3222-09XX 22 22
9 3151-0900 22 9 3152-0900 22 10 3222-10XX 22 22
10 3151-1000 22 10 3152-1000 22 11 3222-11XX 22 22
11 3151-1100 22 11 3152-1100 22 12 3222-12XX 22 22
12 3151-1200 22 12 3152-1200 22 13 3222-13XX 22 22
13 3151-1300 20 13 3152-1300 20 14 3222-14XX 22 22
14 3151-1400 20 14 3152-1400 20 15 3222-15XX 22 22
15 3151-1500 20 15 3152-1500 20 16 3222-16XX 20 20
16 3151-1600 20 16 3152-1600 20 17 3222-17XX 20 20
17 3151-1700 20 17 3152-1700 20 18 3222-18XX 20 20
18 3151-1800 20 18 3152-1800 20 20 3222-20XX 20 20
20 3151-2000 20 20 3152-2000 20 22 3222-22XX 20 20
22 3151-2200 20 22 3152-2200 20 24 3222-24XX 20 20
24 3151-2400 20 24 3152-2400 20 26 3222-26XX 18 18
* Add -100000 to part number for galvanized 28 3222-28XX 18 18
30 3222-30XX 18 18
32 3222-32XX 18 18
34 3222-34XX 18 18
36 3222-36XX 18 18
38 3222-38XX 18 18
40 3222-40XX 18 18
™
MANUAL BLAST GATES

NFMES BLAST GATE MANUAL BLAST GATE
PT. 3241 PT. 3240
Shuts off airflow from machines not in use, improving suction Shuts off airflow from machines not in use, improving suction
elsewhere in the system and energy efficient. Heavy-duty seals elsewhere in the system and energy efficient.
help to prevent leakage from around the closed gate.
←
←
←
“Depth”
← “Depth”
←
←
Height
◄
“D” ►
Dia.
“Height”
“D”
← Dia.
←
←
←
←
←
Width
← “Width”
←
DIAMETER PART WIDTH HEIGHT DEPTH DIAMETER PART WIDTH HEIGHT DEPTH
D (in) NO.* in D (in) NO.* in
3 3241-0300 5.25 7.00 5.375 3 3240-0300 4.25 7.00 5.25
4 3241-0400 6.12 6.25 5.375 4 3240-0400 5.25 7.00 5.50
5 3241-0500 7.00 10.00 5.00 5 3240-0500 6.12 6.25 5.75
6 3241-0600 8.00 11.12 5.00 6 3240-0600 7.00 10.00 5.75
7 3241-0700 9.37 12.00 5.00 7 3240-0700 8.00 11.12 5.38
8 3241-0800 11.00 13.25 5.00 8 3240-0800 9.37 12.00 5.50
9 3241-0900 11.37 14.37 5.00 9 3240-0900 11.00 13.25 5.50
10 3241-1000 13.50 16.25 5.00 10 3240-1000 11.37 14.37 5.50
12 3241-1200 15.75 17.87 5.00 11 3240-1100 11.37 14.37 5.50
14 3241-1400 18.00 28.50 5.00 12 3240-1200 13.50 16.25 5.25
16 3241-1600 18.00 28.50 5.00 14 3240-1400 15.75 17.87 5.25
* Add -100000 to part number for galvanized 16 3240-1600 18.00 28.50 11.25
18 3240-1800 20.80 32.75 11.25
20 3240-2000 22.25 34.00 11.25
22 3240-2200 24.25 33.50 11.25
24 3240-2400 26.25 33.50 11.25
26 3240-2600 29.25 47.50 CALL
28 3240-2800 30.25 47.50 CALL
30 3240-3000 33.25 55.75 CALL
13 Donaldson Torit
™
AUTOMATIC BLAST GATES

AUTO BLAST GATE AUTO BLAST GATE
1-CYLINDER 2-CYLINDER
PT. 3245 PT. 3245
D Ø
D Ø D Ø
D Ø
C
C C
C
B A A A A
B B B
SINGLE CYLINDER TWO CYLINDER

SINGLE CYLINDER TWO CYLINDER
Gates are used as energy saving devices for industrial dust extraction where extraction is not always
needed and where manual control needs to be eliminated. Theses are automatic energy saving blast gates
operated by double-acting compressed air cylinders. Cylinders are controlled by electrically connected
solenoid to machines or remote switch. Uses 120V control circuit and 75psi minimum air pressure.
DIAMETER PART A B C D
(in) NO. in
1 Cylinder
3 3245-0300 16.00 6.38 5.50 5..50
4 3245-0400 16.00 6.30 5.50 5.11
5 3245-0500 17.50 7.50 5.25 6.00
6 3245-0600 20.50 8.66 5.25 7.00
7 3245-0700 22.00 9.44 5.25 7.25
8 3245-0800 25.50 10.25 5.25 8.25
2 Cylinder
9 3245-0900 33.00 17.36 9.00 14.17
10 3245-1000 33.00 17.36 9.00 14.17
12 3245-1200 38.50 20.00 9.00 15.50
14 3245-1400 41.00 23.30 12.00 16.00
16 3245-1600 45.00 23.30 12.00 17.12
18 3245-1800 48.50 25.25 12.00 18.00
20 3245-2000 52.50 27.20 12.00 19.00
22 3245-2200 57.50 29.50 12.00 20.27
™
DIVERTER VALVES
DIVERTER VALVE DIVERTER VALVE

MANUAL AUTOMATIC
PT. 3235 PT. 3236
This length is 6” on D 16” This length is 6” on D 16”

This length is 6” on D 22” This length is 6” on D 12”
Highly efficient, economical method of diverting flow of material or air. Manual or automatic operation.
Constructed of heavy 3/16” thick and painted metal, with welded seams. Supplied with heavy duty flange
bearings, and rubber seal in door. 45˚ angle uses 120V control and closes using 75 psi air pressure.
HOUSING HOUSING
DIAMETER PART B A L DIAMETER PART B A L
GAUGE GAUGE
D (in) NO.* D (in) NO.*
in in in in
3 3235-0345 14 6 26 3/16 3 3236-0345 14 6 26 3/16
4 3235-0445 14 6 26 3/16 4 3236-0445 14 6 26 3/16
5 3235-0545 15¼ 6 27¼ 3/16 5 3236-0545 15¼ 6 27¼ 3/16
6 3235-0645 16 6 28 3/16 6 3236-0645 16 6 28 3/16
7 3235-0745 16 6 28 3/16 7 3236-0745 16 6 28 3/16
8 3235-0845 17 6 29 3/16 8 3236-0845 17 6 29 3/16
9 3235-0945 18 8 34 3/16 9 3236-0945 18 8 34 3/16
10 3235-1045 20 8 36 3/16 10 3236-1045 20 8 36 3/16
11 3235-1145 20 8 36 3/16 11 3236-1145 20 8 36 3/16
12 3235-1245 24 8 40 3/16 12 3236-1245 24 8 40 3/16
13 3235-1345 24 8 40 3/16 13 3236-1345 24 8 40 3/16
14 3235-1445 28 8 44 3/16 14 3236-1445 28 8 44 3/16
15 3235-1545 28 8 44 3/16 15 3236-1545 28 8 44 3/16
16 3235-1645 32 8 48 3/16 16 3236-1645 32 8 48 3/16
17 3235-1745 32 8 48 3/16 17 3236-1745 32 8 48 3/16
18 3235-1845 36 8 52 3/16 18 3236-1845 36 8 52 3/16
20 3235-2045 40 10 60 3/16 20 3236-2045 40 10 60 3/16
22 3235-2245 41¼ 10 61¼ 3/16 22 3236-2245 41¼ 10 61¼ 3/16
24 3235-2445 48 10 68 3/16 24 3236-2445 48 10 68 3/16
* Add -200000 to part number for stainless steel
Add -400000 to part number for black metal
15 Donaldson Torit
™
SUCTION HOOD &

CUSTOM MANIFOLD
SUCTION HOOD SUCTION CUSTOM
RECTANGLE HOOD ROUND MANIFOLD
PT. 3230 PT. 3230 Custom Manifolds are available. Contact
Specify A-E dimensions. Specify A-C dimensions. our sales office for your particular needs.
A
A
A
A
B C D E
B C D E
1 2
MIN MIN B C
1 2
MIN MIN B C
PART NO. NO. OF PICK-UPS

3230-XX02 2
3230-XX03 3
3230-XX04 4
3230-XX05 5
3230-XX06 6
™
ROUTER HOOD, RADIAL ARM SAW

HOOD, & FLOOR SWEEP
ROUTER HOOD RADIAL ARM FLOOR SWEEP
PT. 3231 SAW HOOD PT. 3248
Designed specifically to collect dust PT. 3229 Quick and effective floor cleaning.
from a router. Available with magnets. Used to collect dust from Radial
Edges are folded to inside for safety. Arm Saws.
Standard opening 6” x 12”
D D “D” ←
←
←
←
“D”
←
“L”
↑
10” R=D
←
←
“L” = 12” “C”
← ←“A”
←
1” “B”
←
D
↑ ←
DIAMETER PART DIAMETER PART DIAMETER PART A B C L

D (in) NO. D (in) NO. D (in) NO.* in
3 3231-0300-100000 4 3229-0400-100000 3 3248-0300 6 12 3 17
4 3231-0400-100000 5 3229-0500-100000 4 3248-0400 6 12 3 17
5 3231-0500-100000 6 3229-0600-100000 5 3248-0500 6 12 3 17
6 3231-0600-100000 6 3248-0600 6 12 3 17
7 3231-0700-100000 7 3248-0700 6 12 3 17
8 3231-0800-100000 8 3248-0800 6 12 3 17
9 3231-0900-100000 9 3248-0900 6 12 3 17
10 3231-1000-100000 10 3248-1000 6 12 3 17
With Magnet 11 3248-1100 6 12 3 17
3 3232-0300-100000 12 3248-1200 6 12 3 17
4 3232-0400-100000 * Add -100000 to part number for galvanized
5 3232-0500-100000
6 3232-0600-100000
7 3232-0700-100000
8 3232-0800-100000
9 3232-0900-100000
10 3232-1000-100000
17 Donaldson Torit
™
BUTTERFLY VALVE, BEAM CLAMP,

PIPE BRACING, & HOSE CLAMP
BUTTERFLY VALVE HOSE CLAMP
PT. 3208 PT. 3285
A locking quadrant handle enables users to regulate air volumes Standard hose clamps are used to connect rubber and FDA
in clean air applications. hoses to easy duct hose adapters. From that point, hoses can be
easily detached and re-attached.
Stainless steel only.
“D”
“L”
PART LENGTH DIAMETER PART

DIAMETER D (in) GAUGE
NO.* (L) in (in) NO.
3 3208-0300 8 22 2 3285-0200-200000
4 3208-0400 8 22 3 3285-0300-200000
5 3208-0500 8 22 4 3285-0400-200000
6 3208-0600 8 22 5 3285-0500-200000
7 3208-0700 8 22 6 3285-0600-200000
8 3208-0800 13 22 7 3285-0700-200000
9 3208-0900 13 22 8 3285-0800-200000
10 3208-1000 13 22 9 3285-0900-200000
11 3208-1100 13 20 10 3285-1000-200000
12 3208-1200 13 20 12 3285-1200-200000
13 3208-1300 17 20 14 3285-1400-200000
14 3208-1400 17 20 16 3285-1600-200000
15 3208-1500 17 20 18 3285-1800-200000
16 3208-1600 17 20 20 3285-2000-200000
17 3208-1700 23 20 22 3285-2200-200000
18 3208-1800 23 20 24 3285-2400-200000
20 3208-2000 23 20
22 3208-2200 23 20
24 3208-2400 23 20
* Add -100000 to part number for galvanized. Add -200000 to part number for stainless steel
™
IN-LINE BACK DRAFT DAMPER &

VIEWING SPOOL
IN-LINE BACK DRAFT DAMPER VIEWING SPOOL
PT. 3219 PT. 3205
Used to reduce backward airflow in a horizontal line. Can be mounted An acrylic tube allows operators to visually verify
vertically if airflow is upward: should be specified when ordered. that material in the system is flowing freely.
D + 3.5" B
L
DOOR
D+2 Air Flow D
D D
LENGTH LENGTH
DIAMETER PART L B DIAMETER PART LENGTH
GAUGE GAUGE
D (in) NO.* D (in) NO. * L (in)
in
3 3219-0300 17.5 7 18 3 3205-0300 12.5 22
4 3219-0400 18.5 7 18 4 3205-0400 12.5 22
5 3219-0500 19.5 7 18 5 3205-0500 12.5 22
6 3219-0600 20.5 7 18 6 3205-0600 12.5 22
7 3219-0700 21.5 7 18 7 3205-0700 12.5 22
8 3219-0800 22.5 7 18 8 3205-0800 12.5 22
9 3219-0900 23.5 7 18 9 3205-0900 12.5 22
10 3219-1000 24.5 7 18 10 3205-1000 12.5 22
11 3219-1100 25.5 7 18 11 3205-1100 12.5 22
12 3219-1200 26.5 7 18 12 3205-1200 12.5 22
13 3219-1300 32.5 12 18 13 3205-1300 12.5 20
14 3219-1400 33.5 12 18 14 3205-1400 12.5 20
15 3219-1500 34.5 12 18 15 3205-1500 12.5 20
16 3219-1600 43.5 20 18 16 3205-1600 12.5 20
17 3219-1700 44.5 20 18 18 3205-1800 12.5 20
18 3219-1800 45.5 20 18 20 3205-2000 12.5 20
20 3219-2000 47.5 20 16
22 3219-2200 49.5 20 16
24 3219-2400 51.5 20 16
26 3219-2600 57.5 24 16
28 3219-2800 59.5 24 16
30 3219-3000 61.5 24 16
32 3219-3200 63.5” 24 16
34 3219-3400 65.5 24 16
19 Donaldson Torit
™
BALL JOINT &

VIBRATION ISOLATOR
BALL JOINT VIBRATION ISOLATOR
PT. 3209 PT. 3206
Allows up to 22˚ of movement off-center. Perfect for machines Reduces vibration from the fan to the ducting system.
with moving dust ports.
L
L
Air Flow
D
D D
DIAMETER PART LENGTH LENGTH

GAUGE DIAMETER D (in) PART NO. * GAUGE
D (in) NO. * L (in) L (in)
3 3209-0300 8 20 3 3206-0300 6.5 24

4 3209-0400 9 20 4 3206-0400 6.5 22
5 3209-0500 10.75 20 5 3206-0500 6.5 22
6 3209-0600 11.75 20 6 3206-0600 6.5 22
7 3209-0700 10.75 20 7 3206-0700 6.5 22
8 3209-0800 14 18 8 3206-0800 6.5 22
9 3209-0900 15 18 9 3206-0900 6.5 22
10 3209-1000 14.25 18 10 3206-1000 6.5 22
12 3209-1200 15.25 16 11 3206-1100 6.5 22
14 3209-1400 17.5 14 12 3206-1200 6.5 22
* Add -100000 to part number for galvanized 13 3206-1300 6.5 20
14 3206-1400 6.5 20
15 3206-1500 6.5 20
16 3206-1600 6.5 20
17 3206-1700 6.5 20
18 3206-1800 6.5 20
20 3206-2000 6.5 20
22 3206-2200 6.5 20
24 3206-2400 7 20
26 3206-2600 10 18
28 3206-2800 10 18
30 3206-3000 10 18
32 3206-3200 10 18
34 3206-3400 10 18
36 3206-3600 10 18
38 3206-3800 10 18
40 3206-4000 10 18
™
NO-LOSS STACKHEAD &

BLEED-IN VALVE
NO-LOSS STACKHEAD BLEED-IN VALVE
PT. 3204 PT. 3207
Used when exhausting from fans or stacks through roof. Used to adjust airflow to balance system by introducing
Eliminates back pressure on fan while providing ambient air.
weather protection.
4 x D +6 = L L
D +1 D D
6
6
Angle Flange
for Guying
Bracket Upper To Adjust, Loosen Clamp and Turn
Stack To Short Outer Sleeve To Get Proper Air-flow
QF Duct Section Re-Clamp When Finished
DIAMETER PART DIAMETER PART LENGTH NO. OF

GAUGE GAUGE
D (in) NO.* D (in) NO.* L (in) SLOTS
3 3204-0300 24 3 3207-0300 11 2 24
4 3204-0400 22 4 3207-0400 11 2 22
5 3204-0500 22 5 3207-0500 11 3 22
6 3204-0600 22 6 3207-0600 11 3 22
7 3204-0700 22 7 3207-0700 11 4 22
8 3204-0800 22 8 3207-0800 11 4 22
9 3204-0900 22 9 3207-0900 11 5 22
10 3204-1000 22 10 3207-1000 11 5 22
11 3204-1100 22 11 3207-1100 11 5 22
12 3204-1200 22 12 3207-1200 11 6 22
13 3204-1300 20 13 3207-1300 11 6 20
14 3204-1400 20 14 3207-1400 11 7 20
15 3204-1500 20 15 3207-1500 11 7 20
16 3204-1600 20 16 3207-1600 11 8 20
17 3204-1700 20 17 3207-1700 11 8 20
18 3204-1800 20 18 3207-1800 11 9 20
20 3204-2000 20 20 3207-2000 11 10 20
22 3204-2200 20 22 3207-2200 11 11 20
24 3204-2400 20 24 3207-2400 11 11 20
26 3204-2600 20 * Add -100000 to part number for galvanized
28 3204-2800 20
30 3204-3000 18
32 3204-3200 18
34 3204-3400 18
36 3204-3600 18
38 3204-3800 18
40 3204-4000 18
21 Donaldson Torit
™
O-RING &
HANGERS
O-RING PIPE HANGER HJ PIPE GRIPPLE
PT. 3262 PT. 3265 HANGER HANGER
Replacement O-Ring for Clearance hole 5/16”. PT. 3265HJ PT. 3265
use with Adj. Nipples. Bolt size 1/4” x 3/4”. Clearance hole 7/16”. Bolt Comes in 15 ft. length
Specify Black for standard Bolt are supplied with hanger. size 1/4” x 3/4”. Bolt are
or red for high temp. supplied with hanger.
D
2½” to 3” gap
D D
For all hangers, make sure to check your local codes
to ensure your ducting is supported properly
DIAMETER PART DIAMETER PART DIAMTER WEIGHT

PART NO. PART NO.
D (in) NO.* D (in) NO.* D (in) (lbs)
3 3262-0300 3 3265-0300 3 3265-0300-1HJ Up to 22 3266-1500-022LBS
4 3262-0400 4 3265-0400 4 3265-0400-1HJ Up to 100 3266-1500-100LBS
5 3262-0500 5 3265-0500 5 3265-0500-1HJ Up to 200 3266-1500-200LBS
6 3262-0600 6 3265-0600 6 3265-0600-1HJ Up to 495 3266-1500-495LBS
7 3262-0700 7 3265-0700 7 3265-0700-1HJ Up to 715 3266-1500-715LBS
8 3262-0800 8 3265-0800 8 3265-0800-1HJ
9 3262-0900 9 3265-0900 9 3265-0900-1HJ
10 3262-1000 10 3265-1000 10 3265-1000-1HJ
11 3262-1100 11 3265-1100 11 3265-1100-1HJ
12 3262-1200 12 3265-1200 12 3265-1200-1HJ
13 3262-1300 13 3265-1300 13 3265-1300-1HJ
14 3262-1400 14 3265-1400 14 3265-1400-1HJ
15 3262-1500 15 3265-1500 15 3265-1500-1HJ
16 3262-1600 16 3265-1600 16 3265-1600-1HJ
17 3262-1700 17 3265-1700 17 3265-1700-1HJ
18 3262-1800 18 3265-1800 18 3265-1800-1HJ
20 3262-2000 20 3265-2000 20 3265-2000-1HJ
22 3262-2200 22 3265-2200 22 3265-2200-1HJ
24 3262-2400 24 3265-2400 24 3265-2400-1HJ
26 3265-2600
28 3265-2800
* Call for High Tem part numbers

30 3265-3000
32 3265-3200
34 3265-3400
36 3265-3600
38 3265-3800
40 3265-4000
™
ANGLE FLANGE
ANGLE FLANGE
PT. 3261
I.D. W
H
T
B.C.
DIAMTER PART I.D. H W T B.C. DIAMETER OF

NO. OF BOLTS
(in) NO. in BOLT HOLES
3 3261-0300 15/16 15/16 1 1/8 4 5/16 6 9/32
4 3261-0400 4 1/16 15/16 1 1/8 5 5/16 6 9/32
5 3261-0500 5 1/16 1 1/16 1 1/8 6 5/16 6 9/32
6 3261-0600 6 3/32 1 1 1/8 7 5/16 6 9/32
7 3261-0700 7 1/8 1 1 1/8 1/8 8 1/2 6 3/8
8 3261-0800 8 1/8 1 1/8 1 1/8 1/8 9 5/9 6 3/8
9 3261-0900 9 1/8 1 1/4 1 1/4 1/8 10 5/8 6 7/16
10 3261-1000 10 1/8 1 1/4 1 3/8 1/8 11 4/5 6 7/16
11 3261-1100 11 1/8 1 1/4 1 1/2 1/8 12 3/4 6 7/16
12 3261-1200 12 1/8 1 1/2 1 1/2 1/8 14 8 7/16
13 3261-1300 13 1/8 1 1/2 1 1/2 1/8 15 8 7/16
14 3261-1400 14 1/8 1 1/2 1 1/2 1/8 16 8 7/16
15 3261-1500 15 1/8 1 1/2 1 1/2 3/16 17 8 7/16
16 3261-1600 16 1/8 1 1/2 1 1/2 3/16 18 8 7/16
17 3261-1700 17 1/8 1 1/2 1 1/2 3/16 19 8 7/16
18 3261-1800 18 1/8 1 1/2 1 1/2 3/16 20 8 7/16
19 3261-1900 19 1/8 1 1/2 1 1/2 3/16 20 3/4 12 7/16
20 3261-2000 20 1/8 1 1/2 1 1/2 3/16 21 3/4 12 7/16
21 3261-2100 21 1/8 1 1/2 1 1/2 3/16 22 3/4 12 7/16
22 3261-2200 22 1/8 1 1/2 1 1/2 3/16 23 3/4 12 7/16
23 3261-2300 23 1/8 1 1/2 1 1/2 3/16 24 7/8 12 7/16
24 3261-2400 24 1/8 1 1/2 1 1/2 3/16 25 7/8 12 7/16
25 3261-2500 25 1/8 1 1/2 1 1/2 3/16 26 7/8 16 7/16
26 3261-2600 26 1/8 2 2 3/16 28 3/8 16 7/16
27 3261-2700 27 1/8 2 2 3/16 29 3/8 16 7/16
28 3261-2800 28 1/8 2 2 3/16 30 3/8 16 7/16
29 3261-2900 29 1/8 2 2 3/16 31 3/8 16 7/16
30 3261-3000 30 1/8 2 2 3/16 32 3/8 16 7/16
31 3261-3100 31 1/8 2 2 3/16 33 3/8 16 7/16
32 3261-3200 32 1/8 2 2 3/16 34 3/8 16 7/16
33 3261-3300 33 1/8 2 2 3/16 35 3/8 16 7/16
34 3261-3400 34 1/8 2 2 3/16 36 3/8 16 7/16
35 3261-3500 35 1/8 2 2 3/16 37 3/8 16 7/16
36 3261-3600 36 1/8 2 2 3/16 38 3/8 16 7/16
37 3261-3700 37 1/8 2 2 3/16 39 3/8 24 7/16
38 3261-3800 38 1/8 2 2 3/16 40 3/8 24 7/16
39 3261-3900 39 1/8 2 2 3/16 41 3/8 24 7/16
40 3261-4000 40 1/8 2 2 3/16 42 3/8 24 7/16
23 Donaldson Torit
™
OIL MIST GASKET & O-RING

MOLDED RUBBER GASKET NITRILE RUBBER O-RING
PT. 3190 PT. 3191
Carefully place the gasket along the rolled edge of the part, being These materials work in conjunction with standard O-Ring. It
careful to avoid kinks or voids. Only one gasket is needed per joint. does not replace it.
Join the gasketed end of the pipe to a non-gasketed end of the next Position the larger-diameter standard Nordfab O-Ring above
part in the ducting run using a standard Easy Duct clamp. The oil- the oil-mist ring. The order should be as follows:
mist gasket, in addition to the gasket inside the Easy Duct clamp, a) rolled edge or nipple; against
provides dual protection against leakage. b) soft, small-diameter O-Ring; against
Temp range -30°F to +225°F c) standard Nordfab O-Ring.
→ D → → D →
DIAMETER PART DIAMETER PART

(in) NO. (in) NO.
4 3190-0400-00000 4 3191-0400-00000
5 3190-0500-00000 5 3191-0500-00000
6 3190-0600-00000 6 3191-0600-00000
7 3190-0700-00000 7 3191-0700-00000
8 3190-0800-00000 8 3191-0800-00000
9 3190-0900-00000 9 3191-0900-00000
10 3190-1000-00000 10 3191-1000-00000
11 3190-1100-00000 11 3191-1100-00000
12 3190-1200-00000 12 3191-1200-00000
14 3190-1400-00000 14 3191-1400-00000
16 3190-1600-00000 16 3191-1600-00000
18 3190-1800-00000 18 3191-1800-00000
20 3190-2000-00000 20 3191-2000-00000
22 3190-2200-00000 22 3191-2200-00000
24 3190-2400-00000 24 3191-2400-00000
Airflow
™
INSTALLING AN
ADJUSTABLE NIPPLE
Instructions for using the “easy duct” adjustable nipple with rubber O-Ring for dry system. Each Easy Duct
pipe section is 5’ in length. To shorten to accommodate an existing span, an adjustable nipple is used.
STEP 1 STEP 2
Measure distance to be spanned. Mark distance to be spanned less 4”.
STEP 3 STEP 4
Use O-Ring provided and mark for cut. Drill access hole then cut with saw
STEP 5 STEP 6
Cut piece of pipe put O-Ring on cut pipe, Snap clamp over O-Ring and one end of
slide nipple over nipple.
Finished connection using the adjust nipple assembly.
NOTE: KEEP CUT PIPE IN THE DIRECTION AS THE AIR FLOW.
25 Donaldson Torit
™
SIZING BRANCHES
5” x 90 Deg Elbow
____” (____CFM)
Branch Typ. @ 30 Deg
6” x 60 Deg Elbow
6” Dia @ 885 CFM
5” Dia @ 615 CFM
EXAMPLE: Always work from your machines back toward the filter. Suppose that you have a 5” drop that
rises and runs back to join with a 6” drop as sketched above. What size branch will you need?
8” dia (1500 CFM) 5” x 90 Deg Elbow

From Air Volume
Chart
Branch Typ. @ 30 Deg
6” x 60 Deg Elbow
6” Dia @ 885 CFM
5” Dia @ 615 CFM
The 5” pipe carries 615 CFM at 4500 FPM, (See Chart). The 6” pipe will need 885 CFM at the same velocity
(See Chart). Added together you have a total of (615 + 885) 1500 CFM coming together. Looking again at the
chart under 4500 FPM, you find that 1500 CFM is not listed, but falls very close to the 1570 CFM listed for an
8” pipe. This indicates that the 5” joined to the 6” will require an 8” pipe to carry all of the material at the right
velocity. The branch, therefore, will be 8” on the downstream end reducing down to a 5” with a 6” branching
off of it. That is listed as a 8-6-5 branch.
™
SIZING AN EASY DUCT SYSTEM

Easy Duct offers assistance to those salespeople and customers who have never designed a piping system.
We can assist you in determining the correct pipe size and configuration that will supply you with the correct
flow. Please call an inside Sales Representative for assistance.
USING THE CFM/FPM CHART

This chart allows you to choose the correct pipe size for the CFM that is required. Different materials need
to be conveyed at different velocities to prevent the material from falling out of the air stream. For example,
wood chips and saw dust flow well at 4500 feet per minute. Referring to the chart, a 4” pipe will convey 395
CFM at 4500 FPM. This indicates that a 4” pick-up on a machine will use 395 CFM from the filtering system. Or
working in reverse, if you know that a machine will require approximately 400 CFM to remove the waste, then
you should design a 4” pipe for the application.
AIR VOLUME IN DUCTS IN CUBIC FEET PER MINUTE (CFM)

VELOCITY IN FEET PER MINUTE (FPM)
DIAMETER (IN) 2000 2500 3000 3500 4000 4500 5000 5500 6000 6500 7000
3 100 125 150 170 195 220 245 270 295 320 345
4 175 220 260 305 350 395 440 485 525 570 615
5 275 340 410 475 545 615 680 750 820 885 955
6 395 490 590 685 785 885 980 1080 1180 1275 1375
7 535 670 800 935 1070 1205 1335 1470 1605 1735 1870
8 700 875 1050 1220 1395 1570 1745 1920 2095 2270 2445
9 885 1105 1325 1545 1765 1990 2210 2430 2650 2870 3090
10 1090 1365 1635 1910 2180 2455 2725 3000 3270 3545 3820
11 1320 1650 1980 2310 2640 2970 3300 3630 3960 4290 4620
12 1570 1965 2355 2750 3140 3535 3925 4320 4710 5105 5500
13 1850 2300 2770 3225 3685 4150 4610 5070 5530 5990 6450
14 2140 2675 3205 3740 4275 4810 5345 5880 6415 6950 7485
15 2450 3070 3680 4300 4900 5520 6130 6750 7360 7970 8590
16 2790 3490 4190 4885 5585 6285 6980 7680 8380 9075 9775
17 3150 3940 4730 5515 6300 7090 7880 8670 9450 10240 11030
18 3535 4420 5300 6185 7070 7950 8835 9720 10600 11485 12370
20 4365 5455 6545 7635 8725 9815 10910 12000 13090 14180 15270
22 5280 6600 7920 9240 10560 11880 13200 14520 15840 17160 18480
24 6285 7855 9425 10995 12656 14135 15710 17280 18850 20420 21995
26 7370 9210 11055 12900 14740 16580 18420 20270 22110 23950 25800
28 8550 10685 12820 14960 17100 19230 21310 23500 25650 27780 29920
30 9800 12260 14700 17170 19625 22080 24530 26990 29440 31890 34350
32 11160 13950 16750 19541 22330 25120 27910 30700 33490 26280 39070
34 12600 15755 18905 22055 25210 28360 31510 34660 37810 40965 44115
36 14130 17665 21195 24730 28260 31800 35325 38860 42390 45925 49455
38 15745 19680 23615 27550 31490 35425 39360 43295 47230 51170 55100
40 17445 21800 26170 30530 34890 39250 43610 47975 52330 56700 61055
27 Donaldson Torit
™
CONDITION OF SALE
GENERAL CONDITIONS OF SALE
The terms and conditions of acceptance of sale set forth herein, and all drawings, specifications, descriptions and other documents attached
hereto and incorporated here in by reference constitute the entire agreement between Easy Duct (seller) and the buyer. Seller’s acceptance of
his order is expressly conditioned by the buyer’s consent to the terms contained herein. The terms and conditions of the seller’s proposal (if any)
and acknowledgment shall prevail over any conflicting or different terms in buyer’s order unless buyer notifies seller in writing of its objections
thereto within (15) fifteen days from receipt of seller’s acknowledgment. The failure of Seller to object to any provision in conflict herewith
whether contained in Buyer’s purchase order or otherwise, shall not be construed as a waiver of the provisions hereof nor as an acceptance
thereof. Seller’s proposal is only preliminary unless it is otherwise confirmed. If any of the four terms and conditions of Seller’s proposal conflict
with these general conditions of sale, those contained in the proposal shall prevail.
WARRANTIES
The Seller warrants that the products sold hereunder conform to any applicable drawings and specifications accepted in writing by Seller and
will be free from any defects in material and workmanship which become apparent under normal use, and of which Buyer gives written notice
to Seller within a period of 6 months from the date of installation or 12 months from the date of shipment, whichever period first expires. If, within
that period, the Seller receives from Buyer written notice of any alleged defect in or non-conformance of any product and if, in Seller’s sole
judgement, the product does not conform or is found to be defective in material or workmanship, then Buyer shall, at Seller’s request, return the
part or product F.O.B. Seller’s shipping point and Seller at its option and expense, shall repair or replace the defective part or product or repay the
Buyer the full price paid for such part or product by Buyer. Dismounting and reinstallation of defective or nonconforming parts is done at Buyer’s
expense. Warranty for delivery of spare parts or replacement for non-conforming parts expires when warranty for original equipment expires.
Any repayment of purchase price shall be without interest. Seller’s sole responsibility, and Buyer’s exclusive remedy hereunder shall be limited
to such repair, replacement, or repayment of the purchase price as above provided. There are no other warranties, expressed, statutory or
implied, including those of merchantability, quality or fitness for purpose, nor any affirmation of fact or representation which extends beyond the
description on the face here of. The warranties of Seller do not cover and Seller makes no warranty with respect to:
A) failures not reported to Seller within the warranty period specified above;
B) failure or damage due to misapplication, abuse, improper installation or abnormal conditions of temperature, dirt or other corrosive matter;
C) failures due to operation, either intentional or otherwise, above rated capacities or in an otherwise improper manner;
D) products which have been in any way tampered with or altered by anyone other than an authorized representative of Seller;
E) products damaged in shipment or otherwise without fault of Seller;
F) expenses incurred by Buyer in an attempt to repair or rework any alleged defective product, and defects in material and workmanship which
are attributable to drawings and specifications provided by Buyer.
CLAIMS FOR SHORTAGES

Any claim for loss, breakage (obvious or concealed) are Buyer’s responsibility and should be made to the carrier immediately. Seller will render
Buyer reasonable assistance in securing satisfactory adjustment of such claims. Any notices of shortages or other errors must be made in
writing to Seller within 15 days after receipt of shipment. Failure to give such notice shall constitute unqualified acceptance and a waiver of all
claims by Buyer. Risk of loss for damages to the products sold hereunder passes to Buyer upon delivery to the carrier regardless of who pays
shipping costs.
LIMITATION OF LIABILITY
Seller’s sole responsibility and Buyer’s sole and exclusive remedy with respect to any breach of warranty or guarantee under this agreement
shall be limited to repair, replacement or repayment of the purchase price at Seller’s sole option. Seller’s total responsibility and liability for any
and all claims, damages of any nature, losses, liabilities or costs of corrective efforts, including but not limited to those relating to any warranty
or guarantee arising out of or related to performance of this agreement or the products covered hereunder or the performance thereof shall not
exceed the purchase price. In no event shall Seller be liable for any special, indirect, incidental or consequential damages of any character;
including but not limited to, loss of use of productive facilities or equipment, lost profits, property damage, expense incurred in reliance on
Seller’s performance hereunder or lost production, whether suffered by Buyer or any third party. Seller disclaims all liability for any and all costs,
claims, demands, charges, expenses or other damages, either direct or indirect, incident to all property damages arising out of any cause of
action based on strict liability.
Industry-Leading Technology
• Advanced filtration technology for optimal performance
• Reduced energy consumption and cost of ownership
• Advanced design and testing capabilities
The Most Filters and Parts

• For every brand and style of collector
• Wide range of filtration media for any application
• 90,000 filters and parts in stock and ready to ship
Unparalleled Support
• Live technical specialists
• Comprehensive pre- and post-sale support
• 40 manufacturing plants and 14 distribution centers worldwide
Call Donaldson Torit to get cleaner air today:

® ®
Significantly improve the performance of your collector with genuine Donaldson Torit replacement filters
800-365-1331
and parts. Call Donaldson Torit at 800-365-1331.
DonaldsonTorit.com
Important Notice
Many factors beyond the control of Donaldson can affect the use and performance of Donaldson products in a particular application, including the conditions under which the product is used. Since these
factors are uniquely within the user’s knowledge and control, it is essential the user evaluate the products to determine whether the product is fit for the particular purpose and suitable for the user’s application.
All products, product specifications, availability and data are subject to change without notice, and may vary by region or country.
Donaldson Company, Inc. China Korea

Minneapolis, MN Email: [email protected] Email: [email protected]
Phone: +86-400-820-1038 Phone: +82-2-517-3333
donaldsontorit.com • shop.donaldson.com
Donaldson Europe B.V.B.A. Latinoamerica
Email: [email protected] Email: [email protected]
North America Phone: +32-16-38-3811 Phone: +52-449-300-2442
Email: [email protected] India South Africa
Phone: (USA): +1-800-365-1331 • (MX): +1-800-343-36-39 Email: [email protected] Email: [email protected]
Australasia Phone: +91-124-4807-400 • +18001035018 Phone: +27-11-997-6000
Email: [email protected] Japan Southeast Asia
Phone: +61-2-4350-2000 Email: [email protected] Email: [email protected]
Toll Free: (AU) +1800-345-837 • (NZ) +0800-743-387 Phone: +81-42-540-4112 Phone: +65-6311-7373
F118011 ENG (02/20) Easy-Duct Master Catalog ©2013-2020 Donaldson Company, Inc.
Donaldson, Torit, Easy-Duct and the color blue are marks of Donaldson Company, Inc. All other marks belong to their respective owners.

Easy Duct Master Catalog

Uploaded by

Copyright:

Available Formats

Easy Duct Master Catalog

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Easy Duct Master Catalog

Uploaded by

Copyright:

Available Formats

EASY DUCT ™

THE EASY DUCT

• Clamp-together components can be taken apart

• Flexible - Easily connects to existing ductwork

• Components and adapters fit every system

• Adjustable duct fittings simplify connections

• Smooth interior surface helps prevent clogs

EASY DUCT - AN INVESTMENT

QUICK AND STRONG ASSEMBLY

EFFECTIVE FOR NEW INSTALLATIONS

BLAST NFMES 3241 13 Rubber 3280 6

INSTALLING ADJUSTABLE NIPPLE 25

PRODUCT PHOTOGRAPHS REFERENCE ONLY GENERAL CONDITIONS OF SALES APPLY

EASY DUCT PIPE & FLANGED PIPE

PIPE FLANGED PIPE

← “L” → Van Stone

DIAMETER PART GAUGE LENGTH DIAMETER PART GAUGE LENGTH

3 3200-0300 22 22 0.2 59.25 3 3201-03LW 22 22 59

* Add -100000 to part number for galvanized 30 3201-3016 16 16 59

ADJUSTABLE NIPPLE WITH O-RING

DIAMETER PART LENGTH GAUGE DIAMETER PART

3 3202-0300 11 1/4 22 22 3 3260-0300

ELBOW - STANDARD & LONG RADIUS

C.L.R. 1.5 C.L.R. 2.5 C.L.R.

ELBOW - STANDARD RADIUS

ELBOW - LONG RADIUS

DIAMETER 90° 60° 45° 30° CLR STYLE GAUGE TANGENTS

3 3211-0390-103000 3211-0360-103000 3211-0345-103000 3211-0330-103000 1.0 1.5 P T 24 14 2

* Call 800 number for stainless steel part numbers

3 3214-0390-104500 3214-0360-104500 3214-0345-104500 3214-0330-104500 1.5 16 14 2

4 3214-0490-106000 3214-0460-106000 3214-0445-106000 3214-0430-106000 1.5 16 14 2

5 3214-0590-107500 3214-0560-107500 3214-0545-107500 3214-0530-107500 1.5 14 14 2

6 3214-0690-109000 3214-0660-109000 3214-0645-109000 3214-0630-109000 1.5 14 14 2

8 3214-0890-112000 3214-0860-112000 3214-0845-112000 3214-0830-112000 1.5 14 14 2

ELBOW - TUBED LONG RADIUS

3 3214-0390-107500 3214-0360-107500 3214-0345-107500 3214-0330-107500 2.5 16 14 2

4 3214-0490-110000 3214-0460-110000 3214-0445-110000 3214-0430-110000 2.5 16 14 2

5 3214-0590-112500 3214-0560-112500 3214-0545-112500 3214-0530-112500 2.5 14 14 2

6 3214-0690-115000 3214-0660-115000 3214-0645-115000 3214-0630-115000 2.5 14 14 2

8 3214-0890-120000 3214-0860-120000 3214-0845-120000 3214-0830-120000 2.5 14 22 2

* Call 800 number for stainless steel part numbers

DIAMETER PART DIAMETER DIAMETER PART

1.0 3280-0100-000000 1.5 3281-1500-100000 3.0 3283-0300

1.5 3280-1500-000000 2.0 3281-0200-100000 4.0 3283-0400

2.0 3280-0200-000000 2.5 3281-2500-100000 5.0 3283-0500

2.5 3280-2500-000000 3.0 3281-0300-100000 6.0 3283-0600

3.0 3280-0300-000000 3.5 3281-3500-100000 7.0 3283-0700

3.5 3280-3500-000000 4.0 3281-0400-100000 8.0 3283-0800

6.0 3280-0600-000000 8.0 3281-0800-100000

7.0 3280-0700-000000 9.0 3281-0900-100000

8.0 3280-0800-000000 10.0 3281-1000-100000

9.0 3280-0900-000000 12.0 3281-1200-100000

10.0 3280-1000-000000 14.0 3281-1400-100000

SILENCER & MACHINE ADAPTER

INNER OUTER RAW END APPROX. MAXIMUM

3 12 3106-0300 28 20 3 3249-0300 3.00 2.90 22 5.5 3.18

APPROX. DIAMETER APPROX. DIAMETER DIAMETER LENGTH

3 3250-0300 5.0 22 3 3282-0300 5.5 22 3 8 3251-0300 4.5

BRANCH & Y-BRANCH