1.1. Opcserver Da
1.1. Opcserver Da
* CMD_MPC_PFHWSETP_EN
* CMD_MPC_PWRFACOR_MODE
pf CMD_MPC_PFSETP
deg CMD_MPC_PFSTEPAMPL
* CMD_MPC_VARSTEP_DIS
* CMD_MPC_VARSTEP_EN
s CMD_MPC_STEPWIDTH_S
* CMD_MPC_VARHMISETP_EN
* CMD_MPC_VARHWSETP_EN
* CMD_MPC_VARMODE
Mvar CMD_MPC_VARSETP_KV
Mvar CMD_MPC_VARSTEPAMPL
* CMD_MPC_VARSTEP_DIS
* CMD_MPC_VARSTEP_EN
* CMD_MPC_VOLTHMISETP_EN
* CMD_MPC_VOLTHWSETP_EN
* CMD_MPC_VOLTMODE
kV CMD_MPC_VOLTSETP_KV
* CMD_MPC_VOLTSTEP_DIS
* CMD_MPC_VOLTSTEP_EN
kV CMD_MPC_VOLTSTEPAMPL
* CMD_EN_PF_HWSETP
* PFCRVPFCAP
* PFCRVPFIND
* PFCRVVOLT_DIS
* PFCRVVOLT_EN
percent PFCRVVOLT_HYST
percent PFCRVVOLT_P1
percent PFCRVVOLT_P2
percent PFCRVVOLT_P3
percent PFCRVVOLT_P4
* CMD_EN_PF_SCADASETP
* PFCRVPWR_DIS
* PFCRVPWR_EN
percent PFCRVPWR_HYST
percent PFCRVPWR_P1
percent PFCRVPWR_P2
percent PFCRVPWR_P3
percent PFCRVPWR_P4
* PFCRVPWRPFCAP
* PFCRVPWRPFIND
percent PFCRVPWRVIN
percent PFCRVPWRVOUT
* CMD_EN_PF_REFCRVSETP
pf CMD_PF_DMD_SCADA
percent CND_DNCVOLTHI
percent CND_DNCVOLTLO
* CMD_EN_P_HWSETP
* CMD_DMIHMISETP_EN
* CMD_DMIHWSETP_EN
kW CMD_DMISETP
MW CMD_DMISETP_MW
* CND_DNC_DIS
* CND_DNC_EN
* CND_DNCRPWREST
* CND_DNCRPWRWTG
percent CMD_FRQCRV1_RESV
percent CMD_FRQCRV2_RESV
percent CMD_FRQCRV1_DRPOVER
percent CMD_FRQCRV1_DRPUNDER
* CMD_ENABLE_FREQCURV1
Hz CMD_FA_FRQC1HZ
Hz CMD_FB_FRQC1HZ
Hz CMD_FC_FRQC1HZ
Hz CMD_FD_FRQC1HZ
Hz CMD_FE_FRQC1HZ
percent CMD_FRQCRV1_HILIM
Hz CMD_FHYST_FRQC1HZ
percent CMD_FRQCRV1_LOLIM
percent CMD_FRQCRV2_DRPOVER
percent CMD_FRQCRV2_DRPUNDER
* CMD_ENABLE_FREQCURV2
Hz CMD_FA_FRQC2HZ
Hz CMD_FB_FRQC2HZ
Hz CMD_FC_FRQC2HZ
Hz CMD_FD_FRQC2HZ
Hz CMD_FE_FRQC2HZ
percent CMD_FRQCRV2_HILIM
Hz CMD_FHYST_FRQC2HZ
percent CMD_FRQCRV2_LOLIM
* CMD_DISABLE_POWFREQCTRL
* CMD_DRPREFACT
* CMD_DRPREFPSBL
* CMD_DRPREFRATED
* W_CtrlPwrFrqDrpRefRatedOnl_b1
* CMD_ENABLE_POWFREQCTRL
* CMD_PWRREFACT
* CMD_PWRREFACTRAMP
* CMD_PWRREFPSBL
percent CMD_FRQRESV_THRES
* CMD_Enable_powctrl_SCADA_setpoin
* tCMD_DIS_PARKCURT
* CMD_EN_PARKCURT
* CMD_PSBLRESVPWR_EN
* CMD_DISABLE_POWRAMPCTRL
* CMD_ENABLE_POWRAMPCTRL
* CMD_REGISRESVPWR_EN
kW CMD_P_DMD_SCADA
MW CMD_PMW
percent/min CMD_PWRSETP_SLEWRATE
* CMD_GRPCURT_DIS
* CMD_GRPCURT_EN
* CMD_GRPREF_HMI
* CMD_GRPREF_INTF
* CMD_GRPREF_PERC
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
percent CMD_Perc_GRP01
percent CMD_Perc_GRP02
percent CMD_Perc_GRP03
percent CMD_Perc_GRP04
percent CMD_Perc_GRP05
percent CMD_Perc_GRP06
percent CMD_Perc_GRP07
percent CMD_Perc_GRP08
percent CMD_Perc_GRP09
percent CMD_Perc_GRP10
percent CMD_Perc_GRP11
percent CMD_Perc_GRP12
percent CMD_Perc_GRP13
percent CMD_Perc_GRP14
percent CMD_Perc_GRP15
percent CMD_Perc_GRP16
percent CMD_Perc_GRP17
percent CMD_Perc_GRP18
percent CMD_Perc_GRP19
percent CMD_Perc_GRP20
MW
MW
MW
MW
MW
MW
MW
MW
MW
MW
MW
MW
MW
MW
MW
MW
MW
MW
MW
MW
MW CMD_P_GRP01
MW CMD_P_GRP02
MW CMD_P_GRP03
MW CMD_P_GRP04
MW CMD_P_GRP05
MW CMD_P_GRP06
MW CMD_P_GRP07
MW CMD_P_GRP08
MW CMD_P_GRP09
MW CMD_P_GRP10
MW CMD_P_GRP11
MW CMD_P_GRP12
MW CMD_P_GRP13
MW CMD_P_GRP14
MW CMD_P_GRP15
MW CMD_P_GRP16
MW CMD_P_GRP17
MW CMD_P_GRP18
MW CMD_P_GRP19
MW CMD_P_GRP20
MW
MW
MW
MW
MW
MW
MW
MW
MW
MW
MW
MW
MW
MW
MW
MW
MW
MW
MW
MW
* CMD_SSRATE_EN
percent/min CMD_SSSHUTDNRATE
min CMD_PARKSHUTDN_TIME
* CMD_SHUTDOWN_PLANT
* CMD_STARTUP_PLANT
percent/min CMD_SSSTARTUPRATE
min CMD_PARKSTARTUP_TIME
* CMD_SSTIME_EN
* CMD_RESET
* CMD_QHWSETPEN
* W_CtrlVarQCrvVoltAdjDis_b1
* W_CtrlVarQCrvVoltAdjEn_b1
* CMD_QREFCRVSETPEN
s RPWRCRVVOLT_DELAYTIME
* W_CtrlVarRpwrCrvPwrDis_b1
* W_CtrlVarRpwrCrvPwrEn_b1
* W_CtrlVarRpwrCrvQRatioMax_r32
* W_CtrlVarRpwrCrvQRatioMin_r32
percent W_CtrlVarRpwrCrvRpwr10_r32
percent W_CtrlVarRpwrCrvRpwr100_r32
percent W_CtrlVarRpwrCrvRpwr20_r32
percent W_CtrlVarRpwrCrvRpwr30_r32
percent W_CtrlVarRpwrCrvRpwr40_r32
percent W_CtrlVarRpwrCrvRpwr50_r32
percent W_CtrlVarRpwrCrvRpwr60_r32
percent W_CtrlVarRpwrCrvRpwr70_r32
percent W_CtrlVarRpwrCrvRpwr80_r32
percent W_CtrlVarRpwrCrvRpwr90_r32
kV W_CtrlVarRpwrCrvVoltDB_r32
* RPWRCRV_VOLTDIS
* RPWRCRV_VOLTEN
percent RPWRCRV_VOLTHYST
percent RPWRCRV_VOLTPIN
RPWRCRV_VOLTPOUT
percent
Mvar RPWRCRV_VOLTQNEG
Mvar RPWRCRV_VOLTQPOS
kV W_CtrlVarRpwrCrvVoltRef_r32
* W_CtrlVarRpwrCrvVoltSlope_r32
RPWRCRV_VOLTV1
percent
RPWRCRV_VOLTV2
percent
RPWRCRV_VOLTV3
percent
RPWRCRV_VOLTV4
percent
* CMD_QSCADASETPEN
kvar CMD_Set_demand_reactive_power
Mvar CMD_QMVAR
* CMD_ENBL_AUTOOP_VARB
* CMD_CLOSE_BANK_1
* CMD_TRIP_BANK_1
* CMD_CLOSE_BANK_2
* CMD_TRIP_BANK_2
* CMD_CLOSE_BANK_3
* CMD_TRIP_BANK_3
* CMD_CLOSE_BANK_4
* CMD_TRIP_BANK_4
* CMD_CLOSE_BANK_5
* CMD_TRIP_BANK_5
* CMD_CLOSE_BANK_6
* CMD_TRIP_BANK_6
* CMD_ENBL_MANOP_VARB
* CMD_VOLTAUTONOMOUS
* CMD_EN_V_HWSETP
* CMD_EN_V_SCADASETP
* CMD_VOLTMPCMODE
* CMD_DISABLE_UPHIQ_CTRL
* CMD_ENABLE_UPHIQ_CTRL
* CMD_ENABLE_PWRFACOR_MODE
V CMD_U_DMD_SCADA
kV CMD_U_KV
* CMD_Select_VAR_mode
* W_CtrlVoltVarSlvModeEn_b1
percent CMD_VOLTDROOP
* CMD_ENABLE_VOLTMODE
* W_GridFreqDipSel
* W_GridFreqGenDis
* W_GridFreqGenEn
* W_GridFreqGenFreeze
* W_GridFreqGenK1
* W_GridFreqGenK2
* W_GridFreqGenModePlant
* W_GridFreqGenModeWcs
* W_GridFreqGenNumb
Hz W_GridFreqGenOffset
* W_GridFreqGenRR
s W_GridFreqGenT1
s W_GridFreqGenT2
s W_GridFreqGenT3
min W_GridFreqGenTlim
* W_GridFreqGenUnfreeze
* W_GridFreqSineSel
* W_GridFreqSquareSel
* W_GridFreqStepSel
* W_GridFreqTriangleSel
pf CMD_PF_DMD_SETP1
pf CMD_PF_DMD_SETP2
pf CMD_PF_DMD_SETP3
kW CMD_RR_PWRSPAN1
CMD_RR_PWRSPAN1MW
MW
s CMD_RR_TIMESPAN1
kW CMD_RR_PWRSPAN2
MW CMD_RR_PWRSPAN2MW
s CMD_RR_TIMESPAN2
kvar CMD_Set1stDI_reactive_power
Mvar CMD_Q1MVAR
kvar CMD_Set2ndDI_reactive_power
Mvar CMD_Q2MVAR
kvar CMD_Set3rdDI_reactive_power
Mvar CMD_Q3MVAR
V CMD_U_DMD_SETP1
kV CMD_U1KV
V CMD_U_DMD_SETP2
kV CMD_U2KV
Signal Name Description Alarm OPC Tag
Class Name
SM_InSys_NoErrors 002_No errors Informa EVENT_002
tion
SM_InSys_SystemOK 006_System OK Informa EVENT_006
tion
013_Grid transducer
SM_InGrid_LossTransducer Alarm EVENT_013
communication error
SM_InSys_IOBoardAlarm 014_Any IO board has an Alarm EVENT_014
SM_InSys_ControlPowerAla alarm
015_Failure detected on Alarm EVENT_015
rm control power supply
Informa
SM_CtrlVolt_VregInLimit 034_Voltage regulator in limit EVENT_034
tion
Informa
SM_CtrlVolt_VsetpInLimit 035_Voltage limiter in limit EVENT_035
tion
SM_CtrlVolt_RpwrCmdInLi Informa
036_Var command in limit EVENT_036
mit tion
SM_InGrid_ImbalanceVolta
037_Imbalance voltage Alarm EVENT_037
ge
SM_InGrid_ImbalanceCurre
038_Imbalance current Alarm EVENT_038
nt
SM_InGrid_LossOfLineVolt
039_Loss of line Alarm EVENT_039
age
Warnin
SM_CtrlMPC_ConfigErr 201_MPC configuration error EVENT_201
g
202_Number of configured
SM_CtrlSegGrpTurbIncompl groups or turbines incomplete Warnin
EVENT_202
_b1 g
Park Curtailment
Park Curtailment
Park Curtailment
Park Curtailment
Park Curtailment
Park Shutdown
Plant Misc
Park Curtailment
Park Curtailment
Park Curtailment
Park Curtailment
Park Curtailment
Plant Frequency Droop
Park Curtailment
Park Curtailment
Segmented Curtailment
Segmented Curtailment
Segmented Curtailment
Segmented Curtailment
Storage
Storage
Storage
Storage
Storage
Storage
Storage
Storage
Storage
Storage
Storage
Storage
Storage
Storage
Storage
Storage
Storage
Storage
Storage
Storage
Storage
Storage
Park Curtailment
Park Curtailment
Multi-Plant Coordination
Multi-Plant Coordination
Multi-Plant Coordination
Multi-Plant Coordination
Multi-Plant Coordination
Multi-Plant Coordination
Multi-Plant Coordination
Multi-Plant Coordination
Multi-Plant Coordination
Multi-Plant Coordination
Multi-Plant Coordination
Multi-Plant Coordination
Multi-Plant Coordination
Multi-Plant Coordination
Multi-Plant Coordination
Multi-Plant Coordination
Multi-Plant Coordination
Multi-Plant Coordination
Multi-Plant Coordination
Multi-Plant Coordination
Multi-Plant Coordination
Multi-Plant Coordination
Park Curtailment
Segmented Curtailment
Multi-Plant Coordination
Multi-Plant Coordination
Multi-Plant Coordination
Segmented Curtailment
Park Curtailment
Park Curtailment
Park Curtailment
Park Curtailment
Park Curtailment
Park Curtailment
Park Curtailment
Park Curtailment
Signal Name Description
MVA S_DMD_MVA
MW/s RR1_AVRG_MWS
MW/s RR2_AVRG_MWS
MW DMIPWRDMDAI_MW
MW DMIPWRDMDAILATCH_MW
MW DMI_INTFSETP_MW
MW DMIPWRDMD_MW
percent DMIPWRDMD_PERC
MW DNCPWRDMD_MW
* OutSCADA_FeatureList_u32
MW FREQDROOP_MW
MVA S_ACT_MVA
pf PF_ACT
A I_A_NEW
A I_B_NEW
A I_C_NEW
A I_NEW
Hz FREQ_NEW
MW P_ACT_MW
Mvar Q_ACT_MVAR
kV U_AN_KV
kV U_BN_KV
kV U_CN_KV
kV U_ACT_KV
deg C T_MAX_IO
deg C T_MIN_IO
MW MPC_P_AGG_MW
Mvar MPC_VAR_AGG_MVAR
kV MPC_VOLTREF_LL
* N_MPC_CONNECT
A MPC_I_A
A MPC_I_ACT
A MPC_I_B
A MPC_I_C
* N_MPC_NOTCONTROLLED
* N_MPC_ACTIVE
pf MPC_AREAPF
pf MPC_HMIPFSETP
pf MPC_HWPFSETP
pf MPC_PFSETP
pf MPC_PFSRLIN
pf MPC_PFSRLOUT
deg MPC_PFSTEPAMPL
Mvar MPC_PSBNEGVAR_MVAR
Mvar MPC_PSBPOSVAR_MVAR
MW MPC_PSB_PWR_MW
MW MPC_P_ACT_MW
Mvar MPC_AREAVAR_MVAR
s MPC_STEPWIDTH_S
Mvar MPC_HMIVARSETP_MVAR
Mvar MPC_HWVARSETP_MVAR
kV MPC_VARREGREF_LL
Mvar MPC_VARSETP_MVAR
Mvar MPC_VARSRLIN_MVAR
Mvar MPC_VARSRLOUT_MVAR
Mvar MPC_VARSTEPAMPL_MVAR
kV MPC_VDROOP_LL
kV MPC_AREAVOLT_LL
kV MPC_U_AN_KV
kV MPC_U_BN_KV
kV MPC_U_CN_KV
kV MPC_HMIVOLTSETP_LL
kV MPC_HWVOLTSETP_LL
kV MPCVOLTREF_LL
kV MPC_VOLTSETP_LL
kV MPC_VOLTSRLIN_LL
kV MPC_VOLTSRLOUT_LL
kV MPC_VOLTSTEPAMPL_LL
Mvar Q_BANKNEGDB_MVAR
* SEGCURT_NUMGROUPS
MW PARKCURTDMD_MW
MW P_PARKPSBL_MW
MW P_LOSS_MW
MW P_PARKREF_GRP01
MW P_PARKREF_GRP02
MW P_PARKREF_GRP03
MW P_PARKREF_GRP04
MW P_PARKREF_GRP05
MW P_PARKREF_GRP06
MW P_PARKREF_GRP07
MW P_PARKREF_GRP08
MW P_PARKREF_GRP09
MW P_PARKREF_GRP10
MW P_PARKREF_GRP11
MW P_PARKREF_GRP12
MW P_PARKREF_GRP13
MW P_PARKREF_GRP14
MW P_PARKREF_GRP15
MW P_PARKREF_GRP16
MW P_PARKREF_GRP17
MW P_PARKREF_GRP18
MW P_PARKREF_GRP19
MW P_PARKREF_GRP20
Mvar Q_NEGPSBL_MW
Mvar Q_POSPSBL_MW
pf PF_INTFAI
pf PF_INTFAILATCH
pf PF_INTF
* PF_POI
pf PF_REFCRV
pf PF_DMDSCADA
pf PF_DMD1SCADA
pf PF_DMD2SCADA
pf PF_DMD3SCADA
pf PF_DMD_NEW
pf PF_DMDSRL
pf PF_TESTREF
Mvar Q_BANKPOSDB_MVAR
MW P_ACTAVRG_MW
MW P_INTFAI_MW
MW P_INTFAILATCH_MW
MVA S_INTFAI_MVA
MVA S_INTFAILATCH_MVA
MVA S_INTF_MVA
MW P_CMD_GRP01
MW P_CMD_GRP02
MW P_CMD_GRP03
MW P_CMD_GRP04
MW P_CMD_GRP05
MW P_CMD_GRP06
MW P_CMD_GRP07
MW P_CMD_GRP08
MW P_CMD_GRP09
MW P_CMD_GRP10
MW P_CMD_GRP11
MW P_CMD_GRP12
MW P_CMD_GRP13
MW P_CMD_GRP14
MW P_CMD_GRP15
MW P_CMD_GRP16
MW P_CMD_GRP17
MW P_CMD_GRP18
MW P_CMD_GRP19
MW P_CMD_GRP20
MW P_APWRDMD_MW
MW P_FREEZEDMD_MW
MW P_FREQDMD_MW
MW P_INTFDIGCONF_MW
MW P_INTF_MW
MW P_DMDINTF_GRP01
MW P_DMDINTF_GRP02
MW P_DMDINTF_GRP03
MW P_DMDINTF_GRP04
MW P_DMDINTF_GRP05
MW P_DMDINTF_GRP06
MW P_DMDINTF_GRP07
MW P_DMDINTF_GRP08
MW P_DMDINTF_GRP09
MW P_DMDINTF_GRP10
MW P_DMDINTF_GRP11
MW P_DMDINTF_GRP12
MW P_DMDINTF_GRP13
MW P_DMDINTF_GRP14
MW P_DMDINTF_GRP15
MW P_DMDINTF_GRP16
MW P_DMDINTF_GRP17
MW P_DMDINTF_GRP18
MW P_DMDINTF_GRP19
MW P_DMDINTF_GRP20
* PF_FOLDBACKPERC
MW PWR_POI
MW/s RR1_SETP_MWS
MW/s RR2_SETP_MWS
MW/s RR_DNLIMIT_MWS
MW/s RR_UPLIMIT_MWS
MW P_RATED_MW
MW P_REF_GRP01
MW P_REF_GRP02
MW P_REF_GRP03
MW P_REF_GRP04
MW P_REF_GRP05
MW P_REF_GRP06
MW P_REF_GRP07
MW P_REF_GRP08
MW P_REF_GRP09
MW P_REF_GRP10
MW P_REF_GRP11
MW P_REF_GRP12
MW P_REF_GRP13
MW P_REF_GRP14
MW P_REF_GRP15
MW P_REF_GRP16
MW P_REF_GRP17
MW P_REF_GRP18
MW P_REF_GRP19
MW P_REF_GRP20
MW P_REFPERC_GRP01
MW P_REFPERC_GRP02
MW P_REFPERC_GRP03
MW P_REFPERC_GRP04
MW P_REFPERC_GRP05
MW P_REFPERC_GRP06
MW P_REFPERC_GRP07
MW P_REFPERC_GRP08
MW P_REFPERC_GRP09
MW P_REFPERC_GRP10
MW P_REFPERC_GRP11
MW P_REFPERC_GRP12
MW P_REFPERC_GRP13
MW P_REFPERC_GRP14
MW P_REFPERC_GRP15
MW P_REFPERC_GRP16
MW P_REFPERC_GRP17
MW P_REFPERC_GRP18
MW P_REFPERC_GRP19
MW P_REFPERC_GRP20
MW P_CMD_MW
MW P_DMDSCADA_MW
MW P_DMDSRL_MW
MW P_DMD_MW
MW P_DMD_GRP01
MW P_DMD_GRP02
MW P_DMD_GRP03
MW P_DMD_GRP04
MW P_DMD_GRP05
MW P_DMD_GRP06
MW P_DMD_GRP07
MW P_DMD_GRP08
MW P_DMD_GRP09
MW P_DMD_GRP10
MW P_DMD_GRP11
MW P_DMD_GRP12
MW P_DMD_GRP13
MW P_DMD_GRP14
MW P_DMD_GRP15
MW P_DMD_GRP16
MW P_DMD_GRP17
MW P_DMD_GRP18
MW P_DMD_GRP19
MW P_DMD_GRP20
MW P_DMDSRL_GRP01
MW P_DMDSRL_GRP02
MW P_DMDSRL_GRP03
MW P_DMDSRL_GRP04
MW P_DMDSRL_GRP05
MW P_DMDSRL_GRP06
MW P_DMDSRL_GRP07
MW P_DMDSRL_GRP08
MW P_DMDSRL_GRP09
MW P_DMDSRL_GRP10
MW P_DMDSRL_GRP11
MW P_DMDSRL_GRP12
MW P_DMDSRL_GRP13
MW P_DMDSRL_GRP14
MW P_DMDSRL_GRP15
MW P_DMDSRL_GRP16
MW P_DMDSRL_GRP17
MW P_DMDSRL_GRP18
MW P_DMDSRL_GRP19
MW P_DMDSRL_GRP20
MW/s RAMPRATE_GRP01
MW/s RAMPRATE_GRP02
MW/s RAMPRATE_GRP03
MW/s RAMPRATE_GRP04
MW/s RAMPRATE_GRP05
MW/s RAMPRATE_GRP06
MW/s RAMPRATE_GRP07
MW/s RAMPRATE_GRP08
MW/s RAMPRATE_GRP09
MW/s RAMPRATE_GRP10
MW/s RAMPRATE_GRP11
MW/s RAMPRATE_GRP12
MW/s RAMPRATE_GRP13
MW/s RAMPRATE_GRP14
MW/s RAMPRATE_GRP15
MW/s RAMPRATE_GRP16
MW/s RAMPRATE_GRP17
MW/s RAMPRATE_GRP18
MW/s RAMPRATE_GRP19
MW/s RAMPRATE_GRP20
MW P_REGREF_MW
MW P_RESERVEDMD_MW
Mvar Q_INTFAI_MVAR
Mvar Q_INTFAILATCH_MVAR
Mvar Q_TOTAL_MVAR
* Q_CMD_PU
Mvar Q_CMD_MVAR
Mvar Q_COLLECTOR
Mvar Q_INTF_MVAR
Mvar Q_REFPFCTRL_MVAR
Mvar RPWR_POI
Mvar Q_REFCRV_MVAR
Mvar Q_DMD_MVAR
Mvar Q_DMDSRL_MVAR
Mvar Q_TESTREF_MVAR
Mvar Q_SHUNT_MVAR
MW/s SHUTDN_RATE_MWS
MW/s PWR_SRLRAMPRATE_MW
* SYS_STATE_NEW
MW P_TURBACT_GRP01
MW P_TURBACT_GRP02
MW P_TURBACT_GRP03
MW P_TURBACT_GRP04
MW P_TURBACT_GRP05
MW P_TURBACT_GRP06
MW P_TURBACT_GRP07
MW P_TURBACT_GRP08
MW P_TURBACT_GRP09
MW P_TURBACT_GRP10
MW P_TURBACT_GRP11
MW P_TURBACT_GRP12
MW P_TURBACT_GRP13
MW P_TURBACT_GRP14
MW P_TURBACT_GRP15
MW P_TURBACT_GRP16
MW P_TURBACT_GRP17
MW P_TURBACT_GRP18
MW P_TURBACT_GRP19
MW P_TURBACT_GRP20
Mvar Q_TURBACT_GRP01
Mvar Q_TURBACT_GRP02
Mvar Q_TURBACT_GRP03
Mvar Q_TURBACT_GRP04
Mvar Q_TURBACT_GRP05
Mvar Q_TURBACT_GRP06
Mvar Q_TURBACT_GRP07
Mvar Q_TURBACT_GRP08
Mvar Q_TURBACT_GRP09
Mvar Q_TURBACT_GRP10
Mvar Q_TURBACT_GRP11
Mvar Q_TURBACT_GRP12
Mvar Q_TURBACT_GRP13
Mvar Q_TURBACT_GRP14
Mvar Q_TURBACT_GRP15
Mvar Q_TURBACT_GRP16
Mvar Q_TURBACT_GRP17
Mvar Q_TURBACT_GRP18
Mvar Q_TURBACT_GRP19
Mvar Q_TURBACT_GRP20
MW P_TURBPSBL_GRP01
MW P_TURBPSBL_GRP02
MW P_TURBPSBL_GRP03
MW P_TURBPSBL_GRP04
MW P_TURBPSBL_GRP05
MW P_TURBPSBL_GRP06
MW P_TURBPSBL_GRP07
MW P_TURBPSBL_GRP08
MW P_TURBPSBL_GRP09
MW P_TURBPSBL_GRP10
MW P_TURBPSBL_GRP11
MW P_TURBPSBL_GRP12
MW P_TURBPSBL_GRP13
MW P_TURBPSBL_GRP14
MW P_TURBPSBL_GRP15
MW P_TURBPSBL_GRP16
MW P_TURBPSBL_GRP17
MW P_TURBPSBL_GRP18
MW P_TURBPSBL_GRP19
MW P_TURBPSBL_GRP20
MW P_WTGPSBLCOR_MW
Mvar Q_TURBNEGCAP_GRP01
Mvar Q_TURBNEGCAP_GRP02
Mvar Q_TURBNEGCAP_GRP03
Mvar Q_TURBNEGCAP_GRP04
Mvar Q_TURBNEGCAP_GRP05
Mvar Q_TURBNEGCAP_GRP06
Mvar Q_TURBNEGCAP_GRP07
Mvar Q_TURBNEGCAP_GRP08
Mvar Q_TURBNEGCAP_GRP09
Mvar Q_TURBNEGCAP_GRP10
Mvar Q_TURBNEGCAP_GRP11
Mvar Q_TURBNEGCAP_GRP12
Mvar Q_TURBNEGCAP_GRP13
Mvar Q_TURBNEGCAP_GRP14
Mvar Q_TURBNEGCAP_GRP15
Mvar Q_TURBNEGCAP_GRP16
Mvar Q_TURBNEGCAP_GRP17
Mvar Q_TURBNEGCAP_GRP18
Mvar Q_TURBNEGCAP_GRP19
Mvar Q_TURBNEGCAP_GRP20
Mvar Q_TURBPOSCAP_GRP01
Mvar Q_TURBPOSCAP_GRP02
Mvar Q_TURBPOSCAP_GRP03
Mvar Q_TURBPOSCAP_GRP04
Mvar Q_TURBPOSCAP_GRP05
Mvar Q_TURBPOSCAP_GRP06
Mvar Q_TURBPOSCAP_GRP07
Mvar Q_TURBPOSCAP_GRP08
Mvar Q_TURBPOSCAP_GRP09
Mvar Q_TURBPOSCAP_GRP10
Mvar Q_TURBPOSCAP_GRP11
Mvar Q_TURBPOSCAP_GRP12
Mvar Q_TURBPOSCAP_GRP13
Mvar Q_TURBPOSCAP_GRP14
Mvar Q_TURBPOSCAP_GRP15
Mvar Q_TURBPOSCAP_GRP16
Mvar Q_TURBPOSCAP_GRP17
Mvar Q_TURBPOSCAP_GRP18
Mvar Q_TURBPOSCAP_GRP19
Mvar Q_TURBPOSCAP_GRP20
* UNITS_CONNECTED_GRP01
* UNITS_CONNECTED_GRP02
* UNITS_CONNECTED_GRP03
* UNITS_CONNECTED_GRP04
* UNITS_CONNECTED_GRP05
* UNITS_CONNECTED_GRP06
* UNITS_CONNECTED_GRP07
* UNITS_CONNECTED_GRP08
* UNITS_CONNECTED_GRP09
* UNITS_CONNECTED_GRP10
* UNITS_CONNECTED_GRP11
* UNITS_CONNECTED_GRP12
* UNITS_CONNECTED_GRP13
* UNITS_CONNECTED_GRP14
* UNITS_CONNECTED_GRP15
* UNITS_CONNECTED_GRP16
* UNITS_CONNECTED_GRP17
* UNITS_CONNECTED_GRP18
* UNITS_CONNECTED_GRP19
* UNITS_CONNECTED_GRP20
* UNITS_ONLINE_GRP01
* UNITS_ONLINE_GRP02
* UNITS_ONLINE_GRP03
* UNITS_ONLINE_GRP04
* UNITS_ONLINE_GRP05
* UNITS_ONLINE_GRP06
* UNITS_ONLINE_GRP07
* UNITS_ONLINE_GRP08
* UNITS_ONLINE_GRP09
* UNITS_ONLINE_GRP10
* UNITS_ONLINE_GRP11
* UNITS_ONLINE_GRP12
* UNITS_ONLINE_GRP13
* UNITS_ONLINE_GRP14
* UNITS_ONLINE_GRP15
* UNITS_ONLINE_GRP16
* UNITS_ONLINE_GRP17
* UNITS_ONLINE_GRP18
* UNITS_ONLINE_GRP19
* UNITS_ONLINE_GRP20
* UNITS_STOPPED_GRP01
* UNITS_STOPPED_GRP02
* UNITS_STOPPED_GRP03
* UNITS_STOPPED_GRP04
* UNITS_STOPPED_GRP05
* UNITS_STOPPED_GRP06
* UNITS_STOPPED_GRP07
* UNITS_STOPPED_GRP08
* UNITS_STOPPED_GRP09
* UNITS_STOPPED_GRP10
* UNITS_STOPPED_GRP11
* UNITS_STOPPED_GRP12
* UNITS_STOPPED_GRP13
* UNITS_STOPPED_GRP14
* UNITS_STOPPED_GRP15
* UNITS_STOPPED_GRP16
* UNITS_STOPPED_GRP17
* UNITS_STOPPED_GRP18
* UNITS_STOPPED_GRP19
* UNITS_STOPPED_GRP20
s UTC_TIMESTAMP
MW UTILITYPWRDMD_MW
percent UTILITYPWRDMD_PERC
Mvar Q_DMDSCADA_MVAR
Mvar Q_DMD1SCADA_MVAR
Mvar Q_DMD2SCADA_MVAR
Mvar Q_DMD3SCADA_MVAR
kV U_INTFAILATCH_KV
kV U_INTFAI_KV
kV U_INTF_KV
kV U_COMP_KV
kV VOLTREFLL_KV
kV U_DMDSCADA_KV
kV U_DMD1SCADA_KV
kV U_DMD2SCADA_KV
kV U_TESTREF_KV
kV U_REFVARCTRL_KV
kV VREFDROOOPLL_MW
kV U_LINEDROP_KV
kV U_REF_KV
kV U_DMD_KV
kV U_DMDSRL_KV
* N_WTGAVAIL
deg WIND_DIR_NEW
m/s V_WIND
* N_WTGCONN
* N_WTGONL
MW P_WTGACT_MW
MW P_WTG_MAXMW
MW P_WTGMAXONL_MW
MW P_WTGPSBL_MW
MW P_WTGPSBLONL_MW
Mvar Q_WTGACT_MVAR
* N_WTGSTOPWCS
* N_WTGSTOPHWS
* N_WTGSTOPLWS
Mvar Q_WTGNEG_MVAR
Mvar Q_WTGPOS_MVAR
Detailed Description
The apparent power demand is the input signal to the apparent power to active power translation
function. The demand is driven by the hardware or SCADA setpoint demand
depending on the setpoint source selection.
Direct marketing setpoint that is being sent via an analog input to the WindCONTROL system.
Direct marketing setpoint that is being sent via an analog input with latch to the WindCONTROL
system.
DMI setpoint that is being sent via an interface to the WindCONTROL system. There are
multiple analog input variants available, like simple AI, AI with latch, Communication interface
& also customized interface.
Direct marketing interface demand either through SCADA or Communication interface when
park curtailment is enabled
Direct marketing interface power demand as a percentage of park rated power
Power demand from distribution network control feature. Feature reduces the power output of
the plant to meet reactive power capability requirements.
Bit coded list of supported features used for internal GE purposes.
Power droop value generated by the frequency droop function as a function of frequency
deviation.
Measured apparent power by the WindCONTROL grid measurement device. The primary value
is calculated based on the PT and CT ratios of the system.
Measured power factor by the WindCONTROL grid measurement device.
Measured phase A current by the WindCONTROL grid measurement device. The primary value
is calculated based on the CT ratio of the system.
Measured phase B current by the WindCONTROL grid measurement device. The primary value
is calculated based on the CT ratio of the system.
Measured phase C current by the WindCONTROL grid measurement device. The primary value
is calculated based on the CT ratio of the system.
Average system current calculated by the WindCONTROL system. The primary value is
calculated based on the CT ratio of the system.
Measured frequency by the WindCONTROL grid measurement device.
Measured active power by the WindCONTROL grid measurement device. The primary value is
calculated based on the PT and CT ratios of the system.
Measured reactive power by the WindCONTROL grid measurement device. The primary value
is calculated based on the PT and CT ratios of the system.
Measured phase A voltage as LN by the WindCONTROL grid measurement device. The primary
value is calculated based on the PT ratio of the system.
Measured phase B voltage as LN by the WindCONTROL grid measurement device. The primary
value is calculated based on the PT ratio of the system.
Measured phase C voltage as LN by the WindCONTROL grid measurement device. The primary
value is calculated based on the PT ratio of the system.
Average system voltage calculated by the WindCONTROL system. The primary value is
calculated based on the PT ratio of the system.
Aggregated real power produced by all devices participating in MPC scheme as reported by the
current master
Aggregated reactive power produced by all devices participating in MPC scheme as reported by
the current master
Area bus voltage reference to be regulated by the active devices in the MPC network
Number of configured windfarms in the MPC network connected to the active master in the
MPC network
Measured phase A current by the WindCONTROL grid measurement device at the POR of MPC
system. The primary value is calculated based on the CT ratio of the system.
Average system current at the POR of MPC network calculated by the WindCONTROL system.
The primary value is calculated based on the CT ratio of the system.
Measured phase B current by the WindCONTROL grid measurement device at the POR of MPC
system. The primary value is calculated based on the CT ratio of the system.
Measured phase C current by the WindCONTROL grid measurement device at the POR of MPC
system. The primary value is calculated based on the CT ratio of the system.
Number of configured windfarms in the MPC network that are not participating in the MPC
scheme due to a fault condition and user-initiated action.
Number of connected windfarms participating in the MPC scheme in a master or a slave role
Area PF setpoint slew rate limiter input reported by the current master in MPC system
Area PF setpoint slew rate limiter output reported by the current master in MPC system
Area negative VAR capability in MPC system. The VAR capability aggregates the plant reactive
power capability of all communicating plants in the MPC environment. It doesn't consider line
losses between the plant and the point of regulation.
Area positive VAR capability in MPC system. The VAR capability aggregates the plant reactive
power capability of all communicating plants in the MPC environment. It doesn't consider line
losses between the plant and the point of regulation.
Aggregated possible power produced by all devices participating in MPC scheme as reported by
the current master
Measured area active power by the WindCONTROL grid measurement device at the POR of
MPC network. The primary value is calculated based on the PT and CT ratios of the system.
Actual area VAR at common point of regulation for Multi-Plant Coordination
Voltage reference from area VAR regulator of the master device in the MPC network
Final area VAR setpoint output reported by the current master in MPC system
Area VAR setpoint slew rate limiter input reported by the current master in MPC system
Area VAR setpoint slew rate limiter output reported by the current master in MPC system
Voltage reference from area VAR regulator of the master device in the MPC network
Area voltage setpoint slew rate limiter input reported by the current master in MPC system
Area voltage setpoint slew rate limiter output reported by the current master in MPC system
Before a Cap-bank is tripped or a reactor bank is closed by the WindCONTROL the park level
VAR command must drop below this negative deadband value. Dropping below this value
initiates an integrator to count up. As soon as the integrator reaches a threshold the switching of
banks is executed.
Number of configured groups for the Segmented Curtailment feature.
It interfaces to the ControllerHMI and WindSCADA HMI to automatically configure the
required number of group control screens. In WindSCADA reporting it is used to activeate the
group related reports.
Park curtailment demand via hardware or SCADA interface in MW
Park possible power is the available power at the point of measurement of the windfarm. The
signal considers the collector system losses and the power consumption of stopped turbines.
The park power losses include the collector losses and park consumption. It is calculated by the
difference in the sum of the individual wind turbines reported power and the actual measured
power.
Resulting power reference for the power regulator on group 01
Resulting power reference for the power regulator on group 02
Resulting power reference for the power regulator on group 03
Resulting power reference for the power regulator on group 04
Resulting power reference for the power regulator on group 05
Resulting power reference for the power regulator on group 06
Resulting power reference for the power regulator on group 07
Resulting power reference for the power regulator on group 08
Resulting power reference for the power regulator on group 09
Resulting power reference for the power regulator on group 10
Resulting power reference for the power regulator on group 11
Resulting power reference for the power regulator on group 12
Resulting power reference for the power regulator on group 13
Resulting power reference for the power regulator on group 14
Resulting power reference for the power regulator on group 15
Resulting power reference for the power regulator on group 16
Resulting power reference for the power regulator on group 17
Resulting power reference for the power regulator on group 18
Resulting power reference for the power regulator on group 19
Resulting power reference for the power regulator on group 20
The sum of the individual turbine reported negative reactive power capability plus any
configured inductor banks being controlled by the WindCONTROL. The signal also considers
the windfarm collector system losses that typically are dominated by the line charging term.
The sum of the individual turbine reported positive reactive power capability plus any configured
capacitor banks being controlled by the WindCONTROL. The signal also considers the
windfarm collector system losses that typically are dominated by the line charging term.
Power factor setpoint that is being sent via an analog input to the WindCONTROL system. This
value is sent as a unit-less power factor value from the analog input to the WindCONTROL
system.
Power factor setpoint that originated from an analog input and has been latched into the system.
Latching requires a digital input to go high to latch the value into the system. The latched value
is stored in NVRAM and will be restored after a system reboot.
Power factor demand setpoint from Interface is provided from any configured hardwired or
communication interface. If no interface is configured the demand is set to unity power factor.
Synthesized power factor value at point of interconnection
Power factor demand setpoint from Interface is provided from any configured reference curve
interface. If no interface is configured the demand is set to unity power factor.
Feedback of SCADA/OPC power factor control setpoint demand.
The power factor demand is the input signal to the power factor slew rate limiter. The demand is
driven by the hardware or SCADA setpoint demand depending on the setpoint source selection.
Power factor demand SRL signal is the output of the power factor setpoint slew rate limiter. It's
also the input to the power factor regulator. The slew rate limiter limits the rate of change when
moving to a new setpoint demand. Parameter P_CtrlPf_PhiSRL_r32 is used to define the change
rate.
Power factor setpoint demand from either SCADA, hardwired or communication interface.
Reference also includes the reference from the test step function.
Before a Cap-bank is closed or a reactor bank is tripped by the WindCONTROL the park level
VAR command must exceed this positive deadband value. Exceeding this value initiates an
integrator to count up. As soon as the integrator reaches a threshold the switching of banks is
executed.
Averaged measured active power used for the SCADA possible power report. The time constant
for the first order low pass filter is defined with parameter P_CtrlPwr_PsblPwrTC_r32. For the
reporting in SCADA 10 min averages are used that are calculated by the SCADA system.
Park curtailment setpoint that is being sent via an analog input to the WindCONTROL system.
There are multiple analog input variants available, like simple AI, AI with permissive and AI
with enable/disable pulse.
Park Curtailment setpoint that originated from an analog input and has been latched into the
system. Latching requires a digital input to go high to latch the value into the system. The latched
value is stored in NVRAM and will be restored after a system reboot.
Apparent power setpoint that is being sent via an analog input to the WindCONTROL system.
There are multiple analog input variants available, like simple AI, AI with permissive and AI
with enable/disable pulse.
Apparent power setpoint that originated from an analog input and has been latched into the
system. Latching requires a digital input to go high to latch the value into the system.
Apparent power demand setpoint from hardwired or communication interface. The feedback
signal depends on the configured external interface for the project. If no interface is configured
the signal is preset to the rated site capacity.
Group power command or power regulator output of group 01
Group power command or power regulator output of group 02
Group power command or power regulator output of group 03
Group power command or power regulator output of group 04
Group power command or power regulator output of group 05
Group power command or power regulator output of group 06
Group power command or power regulator output of group 07
Group power command or power regulator output of group 08
Group power command or power regulator output of group 09
Group power command or power regulator output of group 10
Group power command or power regulator output of group 11
Group power command or power regulator output of group 12
Group power command or power regulator output of group 13
Group power command or power regulator output of group 14
Group power command or power regulator output of group 15
Group power command or power regulator output of group 16
Group power command or power regulator output of group 17
Group power command or power regulator output of group 18
Group power command or power regulator output of group 19
Group power command or power regulator output of group 20
Power freeze demand is a park curtailment demand initiated either by a digital input or at the
time the grid frequency exceeds a frequency threshold. On the trigger event the actual park
power is sampled as a limit for the park power output.
Frequency Droop power reference is either sample and hold the actual power at the time of the
frequency excursion or meld over the sample and hold actual park power to the possible park
power. The reference configuration is done on the ControllerHMI. The MW droop is provided in
a separate signal.
Park Curtailment demand from digital confirmation interface. If the digital input is active, the
setpoint defined by parameter P_CtrlPwr_PwrSetpAbsolut1_r32 will be applied to the system.
Park curtailment setpoint demand from hardwired or communication interface. The feedback
signal depends on the configured external interface for the project. If no interface is configured
the signal is preset to the rated park power.
The power factor fold back function can be used in conjunction with apparent power control to
maximize active power production when the system is attempting to maintain a maximum MVA
production limit. The foldback factor is a per unit value to adjust the power factor angle for the
power production optimization.
Synthesized active power at point of interconnection
MW power reference for the percentage reference interface for segmented curtailment group 03
MW power reference for the percentage reference interface for segmented curtailment group 04
MW power reference for the percentage reference interface for segmented curtailment group 05
MW power reference for the percentage reference interface for segmented curtailment group 06
MW power reference for the percentage reference interface for segmented curtailment group 07
MW power reference for the percentage reference interface for segmented curtailment group 08
MW power reference for the percentage reference interface for segmented curtailment group 09
MW power reference for the percentage reference interface for segmented curtailment group 10
MW power reference for the percentage reference interface for segmented curtailment group 11
MW power reference for the percentage reference interface for segmented curtailment group 12
MW power reference for the percentage reference interface for segmented curtailment group 13
MW power reference for the percentage reference interface for segmented curtailment group 14
MW power reference for the percentage reference interface for segmented curtailment group 15
MW power reference for the percentage reference interface for segmented curtailment group 16
MW power reference for the percentage reference interface for segmented curtailment group 17
MW power reference for the percentage reference interface for segmented curtailment group 18
MW power reference for the percentage reference interface for segmented curtailment group 19
MW power reference for the percentage reference interface for segmented curtailment group 20
Park power command is the output of the park power regulator. The command is distributed to
the turbines in the windfarm.
Feedback of SCADA/OPC park curtailment setpoint demand
Park Curtailment SRL signal is the output of the Park Curtailment setpoint slew rate limiter. The
slew rate limiter limits the rate of change when moving to a new setpoint demand. Rate can be
changed via web command that is defined as percentage of registered capacity.
The park curtailment demand is the input signal to the park curtailment slew rate limiter. The
demand is driven by the hardware or SCADA setpoint demand depending on the setpoint source
selection.
Power demand of segmented curtailment group 01
Power demand of segmented curtailment group 02
Power demand of segmented curtailment group 03
Power demand of segmented curtailment group 04
Power demand of segmented curtailment group 05
Power demand of segmented curtailment group 06
Power demand of segmented curtailment group 07
Power demand of segmented curtailment group 08
Power demand of segmented curtailment group 09
Power demand of segmented curtailment group 10
Power demand of segmented curtailment group 11
Power demand of segmented curtailment group 12
Power demand of segmented curtailment group 13
Power demand of segmented curtailment group 14
Power demand of segmented curtailment group 15
Power demand of segmented curtailment group 16
Power demand of segmented curtailment group 17
Power demand of segmented curtailment group 18
Power demand of segmented curtailment group 19
Power demand of segmented curtailment group 20
Slew rate limited power demand of segmented curtailment group 01
Slew rate limited power demand of segmented curtailment group 02
Slew rate limited power demand of segmented curtailment group 03
Slew rate limited power demand of segmented curtailment group 04
Slew rate limited power demand of segmented curtailment group 05
Slew rate limited power demand of segmented curtailment group 06
Slew rate limited power demand of segmented curtailment group 07
Slew rate limited power demand of segmented curtailment group 08
Slew rate limited power demand of segmented curtailment group 09
Slew rate limited power demand of segmented curtailment group 10
Slew rate limited power demand of segmented curtailment group 11
Slew rate limited power demand of segmented curtailment group 12
Slew rate limited power demand of segmented curtailment group 13
Slew rate limited power demand of segmented curtailment group 14
Slew rate limited power demand of segmented curtailment group 15
Slew rate limited power demand of segmented curtailment group 16
Slew rate limited power demand of segmented curtailment group 17
Slew rate limited power demand of segmented curtailment group 18
Slew rate limited power demand of segmented curtailment group 19
Slew rate limited power demand of segmented curtailment group 20
Slew rate limiter ramp rate reference of segmented curtailment group 01
Regulator power reference is determined as the minimum of park curtailment reference and
frequency droop reference. It is the input signal to the park power regulator.
Park Curtailment demand calculated by Reserve Power feature. The reserve power reference is
determined as a percentage of park possible power. The reserve in percentage is setup by the
frequency curve on Frequency Droop.
Reactive power setpoint that is being sent via an analog input to the WindCONTROL system.
Reactive power setpoint that originated from an analog input and has been latched into the
system. Latching requires a digital input to go high to latch the value into the system. The latched
value is stored in NVRAM and will be restored after a system reboot.
Total reactive power command of the wind farm. This value takes into account what the turbines
are being commanded along with any VAR-banks that are being utilized.
Normalized park reactive power command that is distributed to connected turbines in the
windfarm.
Park reactive power command that is distributed to connected turbines in the windfarm.
Calculated collector losses of the windfarm by the difference of sum of computed actual reactive
power of connected turbines and the measured reactive power at the substation.
Reactive power demand setpoint from Interface is provided from any configured hardwired or
communication interface. If no interface is configured the demand is set to 0 Mvar.
Reactive power reference for the VAR regulator when operating in power factor mode. A line
drop compensation term is considered for line drop applications.
Synthesized reactive power at point of interconnection
Reactive power demand setpoint from Reference Curves is provided from the currently
configured function. If no reference curve is configured the demand is set to 0 Mvar.
The reactive power demand is the input signal to the reactive power setpoint slew rate limiter.
The demand is driven by the hardware or SCADA setpoint demand depending on the setpoint
source
Reactive selection.
power demand SRL signal is the output of the reactive power setpoint slew rate limiter.
It's also the input to the reactive power regulator, when operating in VAR mode. The slew rate
limiter limits the rate of change when moving to a new setpoint demand.
Parameter P_CtrlVAR_RPwrSRL_r32 is used to define the change rate.
Reactive power setpoint demand from either SCADA, hardwired or communication interface.
Reference also includes the test step signal reference.
The amount of reactive power being applied by inserted VAR-banks controlled by the
WindCONTROL system.
Park curtailment SRL rate reference defines the change rate of the park curtailment setpoint slew
rate limiter.
Definition of the system state:
0: No error in the system, all regulators are operational. 1: Warning; Any warning is active in
the system
2: Error; At least one error is active in the system
Sum of computed turbine possible power of connected turbines. The signal is corrected by the
power consumption of stopped turbines.
The UTC time represents the seconds lapsed since 1 January 1970 00:00:00.
Park Curtailment demand calculated based on min of park curtailment demand , Apparent power
demand & Power freeze demand. The resulting demand values is defined as utility power
demand.
Utility power demand as a percentage of park rated power
Voltage setpoint that originated from an analog input and has been latched into the system.
Latching requires a digital input to go high to latch the value into the system. The latched value
is stored in NVRAM and will be restored after a system reboot.
Voltage setpoint that is being sent via an analog input to the WindCONTROL system.
Voltage demand setpoint from Interface is provided from any configured hardwired or
communication interface. If no interface is configured the demand is set to the default system
voltage.
Voltage at point of interconnection. This signal is calculated based on the electrical characteristic
of the line between the point of measurement and the point of interconnection. It is used for sites
having line drop compensation.
Limited plant voltage reference reflect the active voltage reference at POI. Reference is either fed
from the voltage setpoint interface or from the VAR regulator. LDC and voltage droop
components are added downstream to this reference to calculate the bus voltage reference.
Feedback of SCADA/OPC voltage control setpoint demand
Voltage setpoint demand from either SCADA, hardwired or communication interface. The
voltage test step function is also combined to this signal.
Voltage reference generated by the VAR regulator. The reference is applied to the input of the
voltage regulator, when the system operates in VAR or power factor mode.
Voltage reference from the voltage droop curve.
Voltage drop on the line between the point of measurement and the point of interconnection. It is
used for sites having line drop compensation.
Substation bus voltage reference that feeds into the voltage regulator. This reference is limited to
the substation voltage limits. This value is expressed as LL-value.
The voltage demand is the input signal to the voltage setpoint slew rate limiter. The demand is
driven by the hardware or SCADA setpoint demand depending on the setpoint source selection.
Voltage demand SRL signal is the output of the voltage setpoint slew rate limiter. It's also the
input to the voltage regulator, when operating in voltage mode. The slew rate limiter limits the
rate of change when moving to a new setpoint demand. Parameter P_CtrlVolt_VoltageSRL_r32
is used to define the change rate.
Number of turbines that are connected to the grid and producing active power.
Number of turbines stopped by the WindCONTROL system. A stop can be initiated by a Park
Shutdown or by Excessive Curtailment. The individual turbine will stay in Stop by External
Device state.