Networking Notes
Networking Notes
Networking Notes
The data link layer is responsible for reliable transmission of data between two adjacent network
devices. One of the critical tasks of this layer is to ensure that the data transmitted is received
accurately and free from errors. There are various error detection and correction techniques used
in the data link layer to ensure reliable transmission of data.
1. Parity Check: This is the simplest error detection technique in which an extra bit, known as
a parity bit, is added to the end of each data unit. The parity bit is set to 0 or 1 so that the
total number of 1's in the data unit and parity bit is even or odd. If the receiver detects an
odd number of errors in the data unit, it knows that an error has occurred.
2. Checksum: In this technique, a sum is calculated over all the data in the packet and
placed in a separate field in the packet header. The receiver also calculates the checksum
and compares it with the value sent by the sender. If the checksums do not match, an
error has occurred, and the packet is discarded.
3. Cyclic Redundancy Check (CRC): This technique involves generating a cyclic code from
the data unit and adding it to the end of the data unit as a checksum. The receiver also
generates the cyclic code and compares it with the checksum sent by the sender. If the
checksums do not match, an error has occurred, and the packet is discarded.
4. Hamming Code: This is an error-correcting code technique that can detect and correct a
single-bit error in the data unit. In this technique, additional redundant bits are added to
the data unit, which helps in detecting and correcting errors.
5. Forward Error Correction (FEC): In this technique, the sender adds redundant information
to the data, which allows the receiver to correct errors without requesting retransmission
of the data. FEC is widely used in applications such as satellite communications and
digital television.
These are some of the common error detection and correction techniques used in the data link
layer. The choice of technique depends on the application requirements and the level of error
detection and correction needed.
Switching is a critical component of modern computer networks, and the choice of switching
technology depends on the specific requirements of the network. Switches can be used to
connect devices within a LAN, or they can be used to connect LANs to create larger networks
such as WANs.
HDLC (High-Level Data Link Control) is a data link layer protocol that is used to establish and
maintain connections between two devices in computer networking. It is a bit-oriented protocol
that provides a reliable and efficient way of transmitting data between devices.
HDLC is used primarily in point-to-point communication links, such as between two routers or
between a router and a leased line. It provides full-duplex communication, allowing both devices
to send and receive data at the same time.
The HDLC protocol uses a frame structure to transmit data between devices. The frame consists
of a header, data, and a trailer. The header contains control information such as the address of
the destination device and the type of frame being transmitted. The data section contains the
actual data being transmitted, and the trailer contains error detection information, such as a CRC
(Cyclic Redundancy Check) value, to ensure the integrity of the data.
1. Information Frames (I-Frames): These frames are used to transmit user data between
devices.
2. Supervisory Frames (S-Frames): These frames are used to provide flow control and error
control between devices. S-Frames include ACK (Acknowledgment) and NAK (Negative
Acknowledgment) frames.
3. Unnumbered Frames (U-Frames): These frames are used for various control functions,
such as establishing and terminating connections, and exchanging control information
between devices.
HDLC is a widely used protocol and is supported by many networking devices, including routers,
switches, and other network devices. It is also used as a basis for other protocols, such as PPP
(Point-to-Point Protocol) and LAPD (Link Access Procedure for the D Channel).
Subnetting
Subnetting is the process of dividing a large network into smaller subnetworks or subnets, to
improve network efficiency and manageability. Subnetting helps to reduce the amount of
broadcast traffic on a network and allows for more efficient use of IP addresses.
Subnetting involves splitting a network into two or more smaller networks by borrowing bits
from the host portion of the IP address to create a network address. The number of bits
borrowed depends on the number of subnets required.
For example, consider a network with the IP address 192.168.0.0/24. The /24 indicates that the
first 24 bits of the IP address are used for the network portion, and the remaining 8 bits are used
for the host portion.
To create two subnets from this network, we need to borrow one bit from the host portion,
leaving 7 bits for hosts. This creates two subnets, each with 126 host addresses. The two subnets
would have network addresses of 192.168.0.0/25 and 192.168.0.128/25.
To create four subnets, we need to borrow two bits from the host portion, leaving 6 bits for
hosts. This creates four subnets, each with 62 host addresses. The four subnets would have
network addresses of 192.168.0.0/26, 192.168.0.64/26, 192.168.0.128/26, and 192.168.0.192/26.
Subnetting also allows for more efficient use of IP addresses, as it enables organizations to
allocate IP addresses only to the devices that need them, rather than assigning an IP address to
every device on the network.
what is Analog-Digital?
Analog-Digital refers to the conversion of analog signals to digital signals or vice versa. It involves
translating continuous analog signals into discrete digital values or transforming digital signals
into corresponding analog representations.
The process of converting analog to digital involves two stages: sampling and quantization. In
sampling, the analog signal is measured at regular intervals, and in quantization, the continuous
signal is approximated by a series of discrete values.
Digital-to-analog conversion is the process of transforming digital signals back into analog
representations. This involves reconstructing a continuous signal from a series of discrete digital
values.
Analog signals are commonly used to represent physical phenomena such as sound,
temperature, and voltage, while digital signals are widely used in computing, communication,
and storage systems.
The advantages of digital signals include their high accuracy, reliability, and ease of processing,
while analog signals offer a wider range of values and can represent continuous data more
accurately.
The choice of analog or digital depends on the application requirements, such as accuracy,
resolution, noise tolerance, and cost. Some applications may require a combination of both
analog and digital signals, such as in mixed-signal circuits or audio processing systems.
what is Channelisation?
Channelization refers to the process of dividing a communication channel or bandwidth into
multiple sub-channels or sub-bands, each of which can carry a separate signal or data stream.
This technique is commonly used in communication systems to improve efficiency and capacity
by allowing multiple users or signals to share the same channel without interference.
In wireless communication, channelization allows multiple devices to transmit and receive data
simultaneously by using different frequency channels or time slots.
Channelization is also used in network routing and switching to allocate bandwidth for specific
applications or users, improving network performance and reducing congestion.
The effectiveness of channelization depends on the available bandwidth, the number of users or
signals, and the modulation techniques used.
There are several types of multiplexing techniques, including time-division multiplexing (TDM),
frequency-division multiplexing (FDM), and wavelength-division multiplexing (WDM).
In TDM, multiple signals are transmitted sequentially over a single channel, with each signal
assigned a specific time slot.
In FDM, multiple signals are transmitted simultaneously over different frequency bands within a
common channel.
In WDM, multiple signals are transmitted over a single optical fiber using different wavelengths
of light.
Overall, multiplexing is an essential technique for optimizing the use of communication channels,
improving network efficiency, and enhancing user experience.
what is BroadBand?
Broadband refers to high-speed internet connections that can transmit large amounts of data
over a communication network or medium.
Broadband connections have a higher data transfer rate and bandwidth than traditional
narrowband connections, enabling faster and more reliable data transmission.
Broadband connections can be delivered through various mediums, including copper wires, fiber
optic cables, and wireless networks.
Broadband internet services are typically provided by internet service providers (ISPs) to
residential, commercial, and industrial customers.
Broadband connections enable a wide range of applications, such as video streaming, online
gaming, cloud computing, and video conferencing.
The term "broadband" is often used to refer to internet connections that provide a minimum
download speed of 25 megabits per second (Mbps) and upload speed of 3 Mbps.
Overall, broadband connections have revolutionized the way we access and use the internet,
providing faster and more reliable internet services that have transformed various industries and
sectors.
The frame format specifies the order, size, and format of the different fields or components of a
data frame, such as the header, data, and trailer.
The header contains control information, such as the source and destination addresses, protocol
type, and error checking codes.
The data field contains the actual data being transmitted, and the trailer contains additional error
checking codes or data to ensure data integrity.
Different communication protocols and standards may have different frame formats depending
on their specific requirements and specifications.
For example, Ethernet frames have a specific format that includes a preamble, start frame
delimiter, destination and source MAC addresses, type/length field, data field, and frame check
sequence.
Frame formats enable efficient and reliable communication between different devices and
systems by ensuring that the transmitted data is properly structured and organized.
Overall, frame formats play a critical role in ensuring that data is transmitted accurately and
efficiently in communication networks.
1. Version: A 4-bit field that specifies the version of the IP protocol being used, which is
typically set to 4 for IPv4.
2. Header length: A 4-bit field that specifies the length of the packet header in 32-bit words.
3. Type of Service (TOS): An 8-bit field that indicates the priority and quality of service of the
packet.
4. Total length: A 16-bit field that specifies the total length of the packet (header and data)
in bytes.
1. Address length: IPv4 addresses are 32 bits long, while IPv6 addresses are 128 bits long.
This means that IPv6 provides a much larger address space than IPv4, which is becoming
increasingly important as more and more devices are connected to the internet.
2. Number of addresses: Due to the larger address space provided by IPv6, the total number
of unique addresses is much larger than with IPv4. In fact, IPv6 provides approximately
3.4 x 10^38 addresses, compared to just 4.3 billion addresses provided by IPv4.
3. Address configuration: IPv4 addresses are typically assigned manually or through DHCP,
while IPv6 addresses can be assigned automatically through a process known as stateless
address autoconfiguration (SLAAC).
4. Header format: IPv6 has a simplified header format compared to IPv4, with fewer fields
and a more efficient format for handling packet fragmentation.
5. Security: IPv6 includes built-in support for IPsec, a suite of protocols used to provide
network security, while IPv4 requires IPsec to be implemented separately.
6. Compatibility: IPv6 is not backwards-compatible with IPv4, which means that devices and
networks need to support both protocols in order to communicate with each other. This
has led to a gradual transition from IPv4 to IPv6 over time.
When the sender transmits data, it places a sequence number on each packet to indicate its
position in the overall sequence of packets. The receiver uses these sequence numbers to keep
track of which packets have been received and which ones are missing.
The sliding window technique allows the sender to transmit a certain number of packets at a time
(known as the window size) without waiting for an acknowledgement from the receiver. As the
receiver receives each packet, it sends an acknowledgement back to the sender indicating which
packets have been successfully received.
The sender can then adjust the size of the window based on the feedback from the receiver,
allowing it to transmit more packets if the network conditions are good, or fewer packets if the
network conditions are poor.
The sliding window technique helps to prevent data loss, reduce congestion on the network, and
improve overall network performance by allowing for more efficient use of available bandwidth.
NAT (Network Address Translation) is a technique used in computer networking to translate
private IP addresses into public IP addresses, allowing devices on a private network to access the
internet.
VPN (Virtual Private Network) is a secure, encrypted connection between two or more devices
over a public network such as the internet, allowing for secure remote access to resources and
data.
Proxy is an intermediary server that acts as a gateway between a user and the internet, allowing
for increased security, anonymity, and control over internet access.
CDMA (Code Division Multiple Access) is a cellular communication technology that allows
multiple users to share the same frequency channel by using unique codes to distinguish
between different transmissions.
POP (Post Office Protocol) is an email retrieval protocol used to retrieve emails from a mail
server and store them on a local device.
SMTP (Simple Mail Transfer Protocol) is an email transfer protocol used to send emails between
servers and to deliver emails from a sender's device to a mail server.
NAT is a technique used to translate private IP addresses into public IP addresses, allowing
devices on a private network to access the internet. NAT works by mapping the private IP
addresses of devices on a local network to a public IP address assigned by an Internet Service
Provider (ISP). This allows multiple devices on a local network to share a single public IP address.
There are two types of NAT: static and dynamic. Static NAT maps a specific private IP address to a
specific public IP address, while dynamic NAT assigns public IP addresses dynamically from a
pool of available addresses. NAT is commonly used in home and small business networks to
provide internet access to multiple devices.
A VPN is a secure, encrypted connection between two or more devices over a public network
such as the internet. VPNs are used to provide secure remote access to resources and data,
allowing users to connect to a private network from a remote location. VPNs work by creating a
secure tunnel between the devices that encrypts all traffic passing through it.
VPNs can be configured in different ways, such as site-to-site, remote access, or client-to-client.
Site-to-site VPNs are used to connect two or more private networks together over a public
network, while remote access VPNs allow remote users to connect securely to a private network.
Client-to-client VPNs allow two or more remote users to connect to each other securely.
Proxy:
A proxy is an intermediary server that acts as a gateway between a user and the internet. Proxies
are used to increase security, anonymity, and control over internet access. Proxies can be used to
filter content, block access to certain websites, or hide the user's IP address.
There are different types of proxies, such as web proxies, reverse proxies, and transparent proxies.
Web proxies are used to access websites through the proxy server, while reverse proxies are used
to distribute traffic to multiple servers. Transparent proxies are used to intercept and modify
network traffic, often for security or caching purposes.
Modem (Modulator-Demodulator):
A modem is a device used to connect a computer or network to the internet over a telephone or
cable line. Modems work by converting digital signals from a computer or network into analog
signals that can be transmitted over a telephone or cable line, and vice versa.
There are different types of modems, such as cable modems, DSL modems, and dial-up modems.
Cable modems are used to provide high-speed internet access over a cable TV network, while
DSL modems are used to provide high-speed internet access over a telephone line. Dial-up
modems are used to provide internet access over a traditional telephone line.
Shifting:
There are different types of shifting, such as frequency shifting, phase shifting, and amplitude
shifting. Frequency shifting involves changing the frequency of a signal, while phase shifting
involves changing the phase of a signal. Amplitude shifting involves changing the amplitude, or
strength, of a signal.
CDMA is a cellular communication technology that allows multiple users to share the same
frequency channel by using unique codes to distinguish between different transmissions. CDMA
works by spreading a signal over a wide frequency band, which allows multiple users to share the
same channel without interfering with each other.
CDMA is used in mobile communication networks to provide voice and data services to mobile
devices. CDMA allows for more efficient use of available bandwidth, which results in higher
capacity and better call quality.
POP (Post Office Protocol):
POP is a protocol used to retrieve email from a mail server. When an email client, such as
Microsoft Outlook or Apple Mail, connects to a mail server using POP, it downloads all of the
email messages from the server to the client's computer or mobile device. Once the email has
been downloaded, it is removed from the server.
POP is a simple protocol that is easy to set up and use. However, it has some limitations. For
example, because POP downloads email to the client's device, it does not allow for email access
from multiple devices. Additionally, because email is removed from the server once it has been
downloaded, it can be difficult to access email from a different device or location.
SMTP is a protocol used to send email from one mail server to another. When an email is sent, it
is sent from the sender's email client to the sender's mail server using SMTP. The sender's mail
server then sends the email to the recipient's mail server using SMTP. Once the email reaches the
recipient's mail server, it is stored until the recipient checks their email using POP or another
email protocol.
SMTP is a reliable and widely used protocol for sending email. However, it does have some
limitations. For example, SMTP does not provide any security features, which means that email
sent using SMTP can be intercepted and read by third parties. Additionally, SMTP can be
vulnerable to spam and other forms of email abuse.
To address these limitations, many email providers and services use additional protocols and
technologies, such as SSL/TLS encryption and spam filters, to improve the security and reliability
of email communication.