1/4/23, 6:20 μ.μ.

Microprocessor - Classification

Microprocessor - Classification

A microprocessor can be classified into three categories −

RISC Processor
RISC stands for Reduced Instruction Set Computer. It is designed to reduce the execution
time by simplifying the instruction set of the computer. Using RISC processors, each instruction
requires only one clock cycle to execute results in uniform execution time. This reduces the
efficiency as there are more lines of code, hence more RAM is needed to store the instructions.
The compiler also has to work more to convert high-level language instructions into machine
code.

Some of the RISC processors are −

Power PC: 601, 604, 615, 620

DEC Alpha: 210642, 211066, 21068, 21164
MIPS: TS (R10000) RISC Processor
PA-RISC: HP 7100LC

Architecture of RISC
RISC microprocessor architecture uses highly-optimized set of instructions. It is used in portable
devices like Apple iPod due to its power efficiency.

https://www.tutorialspoint.com/microprocessor/microprocessor_classification.htm 1/5
1/4/23, 6:20 μ.μ. Microprocessor - Classification

Characteristics of RISC
The major characteristics of a RISC processor are as follows −

It consists of simple instructions.

It supports various data-type formats.

It utilizes simple addressing modes and fixed length instructions for pipelining.

It supports register to use in any context.

One cycle execution time.

“LOAD” and “STORE” instructions are used to access the memory location.
It consists of larger number of registers.

It consists of less number of transistors.

CISC Processor
CISC stands for Complex Instruction Set Computer. It is designed to minimize the number of
instructions per program, ignoring the number of cycles per instruction. The emphasis is on
building complex instructions directly into the hardware.

The compiler has to do very little work to translate a high-level language into assembly level
language/machine code because the length of the code is relatively short, so very little RAM is
required to store the instructions.

Some of the CISC Processors are −

IBM 370/168
VAX 11/780

https://www.tutorialspoint.com/microprocessor/microprocessor_classification.htm 2/5
1/4/23, 6:20 μ.μ. Microprocessor - Classification

Intel 80486

Architecture of CISC
Its architecture is designed to decrease the memory cost because more storage is needed in
larger programs resulting in higher memory cost. To resolve this, the number of instructions per
program can be reduced by embedding the number of operations in a single instruction.

Characteristics of CISC
Variety of addressing modes.
Larger number of instructions.
Variable length of instruction formats.
Several cycles may be required to execute one instruction.
Instruction-decoding logic is complex.
One instruction is required to support multiple addressing modes.

Special Processors
These are the processors which are designed for some special purposes. Few of the special
processors are briefly discussed −

Coprocessor
A coprocessor is a specially designed microprocessor, which can handle its particular function
many times faster than the ordinary microprocessor.

For example − Math Coprocessor.

Some Intel math-coprocessors are −

8087-used with 8086

https://www.tutorialspoint.com/microprocessor/microprocessor_classification.htm 3/5
1/4/23, 6:20 μ.μ. Microprocessor - Classification

80287-used with 80286

80387-used with 80386

Input/Output Processor
It is a specially designed microprocessor having a local memory of its own, which is used to
control I/O devices with minimum CPU involvement.

For example −

DMA (direct Memory Access) controller

Keyboard/mouse controller
Graphic display controller
SCSI port controller

Transputer (Transistor Computer)

A transputer is a specially designed microprocessor with its own local memory and having links
to connect one transputer to another transputer for inter-processor communications. It was first
designed in 1980 by Inmos and is targeted to the utilization of VLSI technology.

A transputer can be used as a single processor system or can be connected to external links,
which reduces the construction cost and increases the performance.

For example − 16-bit T212, 32-bit T425, the floating point (T800, T805 & T9000) processors.

DSP (Digital Signal Processor)

This processor is specially designed to process the analog signals into a digital form. This is
done by sampling the voltage level at regular time intervals and converting the voltage at that
instant into a digital form. This process is performed by a circuit called an analogue to digital
converter, A to D converter or ADC.

A DSP contains the following components −

Program Memory − It stores the programs that DSP will use to process data.

Data Memory − It stores the information to be processed.

Compute Engine − It performs the mathematical processing, accessing the program from
the program memory and the data from the data memory.

Input/Output − It connects to the outside world.

Its applications are −

Sound and music synthesis

Audio and video compression
Video signal processing
2D and 3d graphics acceleration.
https://www.tutorialspoint.com/microprocessor/microprocessor_classification.htm 4/5
1/4/23, 6:20 μ.μ. Microprocessor - Classification

For example − Texas Instrument’s TMS 320 series, e.g., TMS 320C40, TMS320C50.

https://www.tutorialspoint.com/microprocessor/microprocessor_classification.htm 5/5