ME/HF CONTROLLER (RE29A)OR RD-O4 a MF/HF controller RF24B (note type personal computer) is discontinued, so the personal compu ter of RF2SA will be used instead of RF24B The key operation is almost same as RF24B, but the following point was modified. 1. Power-on/off Power-on : Press the "POWER’ key at the bottom of the LCD display. Power-off :In case of Power-off, press the "POWER" for more than 3 seconds. 2. Modification of the Memory RF29A uses the flash ROM instead of the HDD which is used in RF248. 8. Service Command Input Method (refer to "3.6 Service Command and Other Operations ~ (A)Service Command Input Method!" of the MF/HF Radio Equipment Service Manual ) In case of RF29A, input Service Command in condition of LED "Caps" lighting. (note) If LED "Caps" is off and input Service Command, this operation is invalid, 4.Registering ID (refer to "3.6.2 Checking and Registering ID, and Registering NBDP Answerback Code and AAIG ~ (A).Registering ID" of the MF/HF Radio Equipment ‘Service Manual) (note) Before registering ID, you need to remove RF29A from Alarm unit and it connect RF 29A to the Main unit in the Radio rack. This is due to hardware function for preventi ng ID Number missing. (This procedure is necessary for both RF24B and RF29A.) Refer in detail to Fig.1 "Registering ID by RF29A" on next page. ayFig. 1 Registering ID by RF29A OR Pp-of @ Radio rack Main unit MAINT i Power supply unit Connect the power cable to “MF/HF “output terminal (Output-+24V) on the front panel of the power supply unit RZ111A, 1. Remove the RF29A from Alarm unit, and connect it to the “MAINT” conector on the Main unit in the Radio rack. 2. Turn the toggle switch at the left side of the “MAINT” connector to “DISABLE” position, 3. Power on Radio rack and Controller. 4. Set Service command and register ID. 5. After completion of the setting up,turn the toggle switch at the left side of the “MAINT” connector to "NORMAL" position without fail. a)VHF RADIO Ru224A- RUZIE4 CRSS2ci4) HOW TO SET THE SHIP ID NUMBER @ (FOR RU224A/RUZ}8A) edans ant Cautlon: Person who must not carry out the following procedure except service engineer. MENU | — Press "MENU" Key. MENU? Is indleated tages ees MENU? 5 eon 5: Inltaltee CRSP cana display. Then press 5 Key. T Nokey-in. ENTER | Press ENTER” Key. ENTER | Press “ENTER™ Key. Set uw Indleate on LCD display. Group ID : Delete aay on cD 00 : Regtstev addrese OK e nee RCL. Press “KCL” Key for 3-4 sae. ENTER | PS PATER’ Key. ‘System Generation | Indicate on LCD display, | _[Syatem Generation] Indicate on LCD 1: Set self 1D Choose Item No.1. LSet sel 1D deplay. 1 ENTER | Press ENTER" Kev. — ‘Self Wdentification? | Indleate on LCD display. D00000000| Se Dnumberwth T press numeric key. ENTER, Press ENTER’ Key. t Press T° Key. a Indicate on LCD Istev address | splay. a Rs Press °C" Key. th Indicate on LED “OK flicker MENU? ‘Self 1D: OK Edie Ifwrong number was 5: Inltlalize display. set, choose “Edit”. ee | Press °C" Ke: ENTER y [VHF T/Reontrolled | Indicare on LCD display. MENU key to DSC ope. ‘The system turn to normal operation.INM-B Rvs po2B (©) 25 Communication Control (2) Setting Communication Terminal IDs Both a destination ID (DEST-ID) and an originating ID (ORIG-ID) can be set for TLP, FAX and DATA communication terminals. The destination terminal ID is fr shore-origi nated calls, and the originating terminal ID is for ship-orginated calls. Sending/receiving is performed according tothe signaling sequence of the respective call connection, Only a destination terminal ID can set for TLX communication terminals. Set DTB for the distress telephone button and set CREDIT for the credit card reader, Note: Follow the description in section 2.5.2 Preset when setting and checking the telex terminal ID, 1 Setting TLP, FAX and DATA terminal ID Select 1. TLP/FAX TERMINAL ID at the SES CONT menu and press the Enter key. After the TLP/FAX TERMINAL ID menu appears input the following engineer command in uppercase alphanumeric characters. TAN OTSME Use the arrow keys to move the cursor to DEST:ID or ORIG-ID setting for the terminal to be set and press the Enter key; the cursor will flash, Input the ID wl the cursor is flashing and press the Enter key. ‘When all the IDs have been set, press F3 (SET) to complete the settings. Teyome wenn cin « gear natal no SPORES Sa AA, BP OBE me rope rox: “teh GL omens off este = or a oata O83 033. le oe : sc es TLPIFAX TERMINAL ID Meno To delete the input terminal ID, input a space atthe DEST-ID position of the communication terminal to be deleted and press the ENTER key after confirming that the DEST-ID column isblank. Alle items of the Geleted communication terminal wil be deleted simultaneously. Lastly, press thé F3 key.2, How to Check Each Item 2 Setting TLX Terminal ID Input the service engineer command at the SES CONT menu to fetch the MAINTENANCE menu, Select 2. PRESET and press the Enter key; the PRESET menu is displayed. aeser ence NODEMCE Ssuonre Sn Pouwrr Nowa Stearce Conner ED 25ST 2 s.erno sero S.OMGAUTTON Not oN m2 Geemm, et ontemane oao Select 11. TLX DEST-ID and press the Enter key: the cursor flashes at ‘he ID input Geld. Input he ID and press the Ener key. Lastly press the NU | F3 key, Switch the power to the CU OFF/ON to save the setting.