Scribd
Upload
63 views7 pages

How To Save Logs and Unitinfo in IP10

This document provides instructions for installing and configuring FileZilla FTP server software on a PC to allow for downloading software updates via FTP. It describes downloading and extracting the FileZilla zip file, stopping the Windows FTP service, adding an anonymous user account, configuring a shared folder on the C drive, and verifying the server is running correctly. The instructions are for setting up an FTP server to archive and upload logs from an IP-10 device.

Uploaded by

Sunil Karnval
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
63 views7 pages

How To Save Logs and Unitinfo in IP10

This document provides instructions for installing and configuring FileZilla FTP server software on a PC to allow for downloading software updates via FTP. It describes downloading and extracting the FileZilla zip file, stopping the Windows FTP service, adding an anonymous user account, configuring a shared folder on the C drive, and verifying the server is running correctly. The instructions are for setting up an FTP server to archive and upload logs from an IP-10 device.

Uploaded by

Sunil Karnval
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

FileZilla

Quick Installation Guide

PROPRIETARY

1. Installing FTP-Server Software


You may install and use any FTP-Server software. Ceragon recommends using FileZilla_Server-0_9_26 software that can be downloaded from the web (freeware). 1. Download zipped FileZilla_Server-0_9_26.zip from the internet and store it on the PC (for example, C:\IP-10). 2. Extract the file and run the installation setup. Follow installation process until finished (do not change any of the installation default settings).

1.1.

Initial Configuration of FTP-Server Software

After installing the FileZilla, it has to be configured to allow the SW download using FTP. Stopping Windows FTP services In order to use FileZilla, Windows default FTP services have to be stopped. 1. Go to Control Panel > Administrative Tools Internet Information Services, if the Internal Information Services dont appear its means that the Windows FTP wasnt install and you may have to proceed without doing so. 2. Use Right-Click to stop the Default FTP Site under FTP Sites.

Configuration of the FTP-Server software User and files path have to be defined on the FTP-Server. 1. Launch the FileZilla Server Interface (go to Files Programs FileZilla Server FileZilla Server Interface).

IP-10 Quick Startup Guide

Doc Rev0.1

PROPRIETARY

2. Click OK on the Connect to Server window. The FileZilla Server window will be displayed.

3. Select Edit Users Shared Folders. The Users window will be displayed.

4. Select Add on the Users section and enter anonymous in the Add user Account window.

5. Select Add on the Shared Folders section and select local drive C:\ in the Browse for Folder.

IP-10 Quick Startup Guide

Doc Rev0.1

PROPRIETARY

6. Select (check) Read, Write and Delete in the Files section. 7. Verify your configuration is identical to the displayed in the following window:

8. Select OK and close the FileZilla server. Launching of the FTP-Server software User and files path have to be defined on the FTP-Server. 1. Launch the FileZilla Server Interface (go to Files Programs FileZilla Server FileZilla Server Interface).

2. Click OK on the Connect to Server window. The FileZilla Server window will be displayed.

IP-10 Quick Startup Guide

Doc Rev0.1

PROPRIETARY

3. Verify server is running (yellow lightning Bolt on top-left corner highlighted and status is Logged On.

IP-10 Quick Startup Guide

Doc Rev0.1

PROPRIETARY

2. IP10 LOGs 2.1. Go to Configuration Management

2.2.

Set FTP Parameters

2.2.1. Enter your Laptop IP in Server IP address.. 2.2.2. Enter // at server file location path. 2.2.3. User Name(anonymous)

Apply
IP-10 Quick Startup Guide 6 Doc Rev0.1

PROPRIETARY

2.3. Create Archive and then Upload archive for any of the option(Configuration/Unit Information/Download Configuration Status & Commands) as per your requirement.

The Zip File will automatically save in C:/ drive.

IP-10 Quick Startup Guide

Doc Rev0.1

You might also like