ncp300 D

NCP300, NCP301
Voltage Detector Series

The NCP300 and NCP301 series are second generation ultra−low
current voltage detectors. These devices are specifically designed for
use as reset controllers in portable microprocessor based systems
where extended battery life is paramount.
Each series features a highly accurate undervoltage detector with www.onsemi.com
hysteresis which prevents erratic system reset operation as the
comparator threshold is crossed. MARKING DIAGRAM
The NCP300 series consists of complementary output devices that 5
are available with either an active high or active low reset output. The TSOP−5/
5 SOT23−5 xxx AYWG
NCP301 series has an open drain N−Channel output with either an G
1 CASE 483
active high or active low reset output.
1
The NCP300 and NCP301 device series are available in the
Thin TSOP−5 package with standard undervoltage thresholds. xxx = Specific Device Code
A = Assembly Location
Additional thresholds that range from 0.9 V to 4.9 V in 100 mV steps
Y = Year
can be manufactured. W = Work Week
Features G = Pb−Free Package
• Quiescent Current of 0.5 mA Typical (Note:Microdot may be in either location)
• High Accuracy Undervoltage Threshold of 2.0%
• Wide Operating Voltage Range of 0.8 V to 10 V PIN CONNECTIONS
• Complementary or Open Drain Reset Output Reset
1 5 N.C.
• Active Low or Active High Reset Output Output
• Specified Over the −40°C to +125°C Temperature Range Input 2

(Except for Voltage Options from 0.9 to 1.1 V)
Ground 3 4 N.C.
• NCV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100 (Top View)
Qualified and PPAP Capable
• These Devices are Pb−Free and are RoHS Compliant ORDERING INFORMATION
Typical Applications
• Microprocessor Reset Controller See detailed ordering and shipping information in the ordering
information section on page 21 of this data sheet.
• Low Battery Detection
• Power Fail Indicator
• Battery Backup Detection
NCP300xSNxxT1 NCP301xSNxxT1
Complementary Output Configuration Open Drain Output Configuration
2 2
Input Input 1
Reset Output
* 1
Reset Output
*
Vref Vref
3 3
GND GND
* The representative block diagrams depict active low reset output ‘L’ suffix devices. The comparator
inputs are interchanged for the active high output ‘H’ suffix devices.
This device contains 25 active transistors.
Figure 1. Representative Block Diagrams
© Semiconductor Components Industries, LLC, 2016 1 Publication Order Number:

October, 2017 − Rev. 30 NCP300/D
NCP300, NCP301
MAXIMUM RATINGS
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Rating Symbol Value Unit
Input Power Supply Voltage (Pin 2) Vin 12 V
Output Voltage (Pin 1) VOUT V
Complementary, NCP300 −0.3 to Vin +0.3
N−Channel Open Drain, NCP301 −0.3 to 12
Output Current (Pin 1) (Note 2) IOUT 70 mA
Thermal Resistance Junction−to−Air RqJA 250 °C/W
Maximum Junction Temperature TJ +150 °C
Operating Ambient Temperature Range
All Voltage Options: 0.9 V to 1.1 V TA −40 to +85 °C
All Voltage Options: 1.2 V to 4.9 V TA −40 to +125 °C
Storage Temperature Range Tstg −55 to +150 °C
Moisture Sensitivity Level MSL 1
Latchup Performance (Note 3) ILATCHUP mA
Positive 200
Negative 200
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. This device series contains ESD protection and exceeds the following tests:
Human Body Model 2000 V per MIL−STD−883, Method 3015.
Machine Model Method 200 V.
2. The maximum package power dissipation limit must not be exceeded.
T *T
J(max) A
P +
D R
qJA
3. Maximum ratings per JEDEC standard JESD78.
www.onsemi.com
2
NCP300, NCP301
ELECTRICAL CHARACTERISTICS (For all values TA = −40°C to +125°C, unless otherwise noted.)
Characteristic Symbol Min Typ Max Unit
NCP300/1 − 0.9 / NCV300/1 − 0.9 (TA = 255C for voltage options from 0.9 to 1.1 V)
Detector Threshold (Pin 2, Vin Decreasing) VDET− 0.882 0.900 0.918 V
Detector Threshold Hysteresis (Pin 2, Vin Increasing) VHYS 0.027 0.045 0.063 V
Supply Current (Pin 2) Iin mA
(Vin = 0.8 V) − 0.20 0.6
(Vin = 2.9 V) − 0.45 1.2
Maximum Operating Voltage (Pin 2) Vin(max) − − 10 V
Minimum Operating Voltage (Pin 2) Vin(min) − 0.55 0.70 V
(TA = −40°C to 85°C) − 0.65 0.80
Reset Output Current (Pin 1, Active Low ‘L’ Suffix Devices) IOUT mA
N−Channel Sink Current, NCP300, NCP301
(VOUT = 0.05 V, Vin = 0.70 V) 0.01 0.05 −
(VOUT = 0.50 V, Vin = 0.85 V) 0.05 0.50 −
P−Channel Source Current, NCP300
(VOUT = 2.4 V, Vin = 4.5 V) 1.0 6.0 −
Reset Output Current (Pin 1, Active High ‘H’ Suffix Devices) IOUT mA
(VOUT = 0.5 V, Vin = 1.5 V) 1.05 2.5 −
(VOUT = 0.4 V, Vin = 0.7 V) 0.011 0.04 −
(VOUT = GND, Vin = 0.8 V) 0.014 0.08 −
Propagation Delay Input to Output (Figure 2) ms
Complementary Output NCP300 Series
Output Transition, High to Low tpHL − 97 −
Output Transition, Low to High tpLH − 77 300
N−Channel Open Drain NCP301 Series
Output Transition, Low to High tpLH − − 300
NCP300/1 − 1.8 / NCV300/1 − 1.8

Detector Threshold (Pin 2, Vin Decreasing) (TA = 25°C) VDET− 1.764 1.80 1.836 V
(TA = −40°C to 125°C) 1.746 − 1.854
(Vin = 1.7 V) − 0.23 0.7
(Vin = 3.8 V) − 0.48 1.3
Minimum Operating Voltage (Pin 2) (TA = 25°C) Vin(min) − 0.55 0.70 V
(TA = −40°C to 125°C) − 0.65 0.80
(VOUT = 0.05V, Vin = 0.70 V) 0.01 0.05 −
(VOUT = 0.50V, Vin = 1.5 V) 1.0 2.0 −
(VOUT = 2.4 V, Vin = 4.5 V) 1.0 6.0 −
(VOUT = 0.5 V, Vin = 5.0 V) 6.3 11 −
(VOUT = 0.4 V, Vin = 0.7 V) 0.011 0.04 −
(VOUT = GND, Vin = 1.5 V) 0.525 0.6 −
www.onsemi.com
3
NCP300, NCP301
ELECTRICAL CHARACTERISTICS (continued) (For all values TA = −40°C to +125°C, unless otherwise noted.)
NCP300/1 − 1.8 / NCV300/1 − 1.8
NCP300/1 − 2.0 / NCV300/1 − 2.0

(TA = −40°C to 125°C) 1.94 − 2.06
(Vin = 1.9 V) − 0.23 0.8
(Vin = 4.0 V) − 0.48 1.3
(TA = −40°C to 125°C) − 0.65 0.80
(VOUT = 0.05V, Vin = 0.70V) 0.01 0.14 −
(VOUT = 0.50V, Vin = 1.5V) 1.0 3.5 −
(VOUT = 2.4V, Vin = 4.5V) 1.0 9.7 −
(VOUT = 0.5 V, Vin = 5.0 V) 6.3 11 −
(VOUT = 0.4 V, Vin = 0.7 V) 0.011 0.04 −
(VOUT = GND, Vin = 1.5 V) 0.525 0.6 −
NCP300/1 − 2.2 / NCV300/1 − 2.2

(TA = −40°C to 125°C) 2.134 − 2.266
(Vin = 2.1 V) − 0.23 0.8
(Vin = 4.2 V) − 0.48 1.3
(TA = −40°C to 125°C) − 0.65 0.80
(VOUT = 0.05V, Vin = 0.70V) 0.01 0.14 −
(VOUT = 0.50V, Vin = 1.5V) 1.0 3.5 −
(VOUT = 2.4V, Vin = 4.5V) 1.0 9.7 −
(VOUT = 0.5 V, Vin = 5.0 V) 6.3 11 −
www.onsemi.com
4
NCP300, NCP301
NCP300/1 − 2.2 / NCV300/1 − 2.2
(VOUT = 0.4 V, Vin = 0.7 V) 0.011 0.04 −
(VOUT = GND, Vin = 1.5 V) 0.525 0.6 −
NCP300/1− 2.7 / NCV300/1− 2.7

(TA = −40°C to 125°C) 2.619 − 2.781
(Vin = 2.6 V) − 0.25 0.8
(Vin = 4.7 V) − 0.50 1.3
(TA = −40°C to 125°C) − 0.65 0.80
(VOUT = 0.05V, Vin = 0.70V) 0.01 0.14 −
(VOUT = 0.50V, Vin = 1.5V) 1.0 3.5 −
(VOUT = 2.4V, Vin = 4.5V) 1.0 9.7 −
(VOUT = 0.5 V, Vin = 5.0 V) 6.3 11 −
(VOUT = 0.4 V, Vin = 0.7 V) 0.011 0.04 −
(VOUT = GND, Vin = 1.5 V) 0.525 0.6 −
NCP300/1− 2.8 / NCV300/1− 2.8

(TA = −40°C to 125°C) 2.716 − 2.884
(Vin = 2.7 V) − 0.25 0.8
(Vin = 4.8 V) − 0.5 1.3
(TA = −40°C to 125°C) − 0.65 0.8
(VOUT = 0.05V, Vin = 0.70V) 0.01 0.14 −
(VOUT = 0.50V, Vin = 1.5V) 1.0 3.5 −
www.onsemi.com
5
NCP300, NCP301
NCP300/1− 2.8 / NCV300/1− 2.8
(VOUT = 2.4V, Vin = 4.5V) 1.0 9.7 −
(VOUT = 0.5 V, Vin = 5.0 V) 6.3 11 −
(VOUT = 0.4 V, Vin = 0.7 V) 0.011 0.04 −
(VOUT = GND, Vin = 1.5 V) 0.525 0.6 −
NCP300/1 − 3.0 / NCV300/1 − 3.0

(TA = −40°C to 125°C) 2.91 − 3.09
(Vin = 2.87 V) − 0.25 0.9
(Vin = 5.0 V) − 0.50 1.3
(TA = −40°C to 125°C) − 0.65 0.80
(VOUT = 0.05V, Vin = 0.70V) 0.01 0.14 −
(VOUT = 0.50V, Vin = 1.5V) 1.0 3.5 −
(VOUT = 2.4V, Vin = 4.5V) 1.0 9.7 −
(VOUT = 0.5 V, Vin = 5.0 V) 6.3 11 −
(VOUT = 0.4 V, Vin = 0.7 V) 0.011 0.04 −
(VOUT = GND, Vin = 1.5 V) 0.525 0.6 −
NCP300/1 − 4.5 / NCV300/1 − 4.5

(TA = −40°C to 125°C) 4.365 − 4.635
(Vin = 4.34 V) − 0.33 1.0
(Vin = 6.5 V) − 0.52 1.4
www.onsemi.com
6
NCP300, NCP301
NCP300/1 − 4.5 / NCV300/1 − 4.5
(TA = −40°C to 125°C) − 0.65 0.80
(VOUT = 0.05V, Vin = 0.70V) 0.01 0.05 −
(VOUT = 0.50V, Vin = 1.5V) 1.0 2.0 −
(VOUT = 5.9V, Vin = 8.0V) 1.5 10.5 −
(VOUT = 0.5 V, Vin = 5.0 V) 6.3 11 −
(VOUT = 0.4 V, Vin = 0.7 V) 0.011 0.04 −
(VOUT = GND, Vin = 1.5 V) 0.525 0.6 −
NCP300/1 − 4.7 / NCV300/1 − 4.7

(TA = −40°C to 125°C) 4.559 − 4.841
(Vin = 4.54 V) − 0.34 1.0
(Vin = 6.7 V) − 0.53 1.4
(TA = −40°C to 125°C) − 0.65 0.80
(VOUT = 0.05V, Vin = 0.70V) 0.01 0.05 −
(VOUT = 0.50V, Vin = 1.5V) 1.0 2.0 −
(VOUT = 5.9V, Vin = 8.0V) 1.5 10.5 −
(VOUT = 0.5 V, Vin = 5.0 V) 6.3 11 −
(VOUT = 0.4 V, Vin = 0.7 V) 0.011 0.04 −
(VOUT = GND, Vin = 1.5 V) 0.525 0.6 −
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
www.onsemi.com
7
NCP300, NCP301
VDET+ + 2
Input Voltage, Pin 2
0.7
0V
5V
Reset Output Voltage, Pin 1

2.5 V NCP301L
Open Drain
0.5 V
0V
VDET+ + 2
Reset Output Voltage, Pin 1 VDET+ + 2

NCP300L
2
Complementary
0.1 V
0V
tpLH tpHL
NCP300 and NCP301 series are measured with a 10 pF capacitive load. NCP301 has an additional 470 k pull−up resistor connec-
ted from the reset output to +5.0 V. The reset output voltage waveforms are shown for the active low ‘L’ devices. The upper detector
threshold, VDET+ is the sum of the lower detector threshold, VDET− plus the input hysteresis, VHYS.
Figure 2. Propagation Delay Measurement Conditions
www.onsemi.com
8
NCP300, NCP301
Table 1. ELECTRICAL CHARACTERISTIC TABLE FOR 0.9 − 4.9 V

Supply Current Nch Sink Current
Detector Threshold Pch Source
NCP300 Series Detector Threshold Hysteresis Vin Low Vin High Vin Low Vin High Current
Iin (mA) Iin (mA) IOUT (mA) IOUT (mA) IOUT (mA)
VDET− (V) (Note 4) VHYS (V) (Note 5) (Note 6) (Note 7) (Note 8) (Note 9)
Part Number Min Typ Max Min Typ Max Typ Typ Typ Typ Typ
NCP300LSN09T1 0.882 0.9 0.918 0.027 0.045 0.063 0.20 0.45 0.05 0.5 2.0
NCP300LSN18T1 1.764 1.8 1.836 0.054 0.090 0.126 0.23 0.48
NCP300LSN185T1 1.813 1.85 1.887 0.056 0.093 0.130
NCP300LSN20T1 1.960 2.0 2.040 0.060 0.100 0.140
NCP300LSN25T1 2.45 2.5 2.55 0.075 0.125 0.175 0.25 0.50
NCP300LSN27T1 2.646 2.7 2.754 0.081 0.135 0.189 0.25 0.50
NCP300LSN28T1 2.744 2.8 2.856 0.084 0.140 0.196
NCP300LSN30T1 2.940 3.0 3.060 0.090 0.150 0.210
NCP300LSN33T1 3.234 3.3 3.366 0.099 0.165 0.231
NCP300LSN34T1 3.332 3.4 3.468 0.102 0.170 0.238
NCP300LSN44T1 4.312 4.4 4.488 0.132 0.220 0.308
NCP300LSN45T1 4.410 4.5 4.590 0.135 0.225 0.315 0.33 0.52
NCP300LSN46T1 4.508 4.6 4.692 0.138 0.230 0.322
NCP300LSN47T1 4.606 4.7 4.794 0.141 0.235 0.329 0.34 0.53
4. Values shown apply at +25°C only. For voltage options greater than 1.1 V, VDET− limits over operating temperature range (−40°C to +125°C)
are VNOM ±3%. For voltage options < 1.2 V, VDET− is guaranteed only at +25°C.
5. Condition 1: 0.9 − 2.9 V, Vin = VDET− − 0.10 V; 3.0 − 3.9 V, Vin = VDET− − 0.13 V; 4.0 − 4.9 V, Vin = VDET− − 0.16 V
6. Condition 2: 0.9 − 4.9 V, Vin = VDET− + 2.0 V
7. Condition 3: 0.9 − 4.9 V, Vin = 0.7 V, VOUT = 0.05 V, Active Low ‘L’ Suffix Devices
8. Condition 4: 0.9 − 1.0 V, Vin = 0.85 V, VOUT = 0.5 V; 1.1 − 1.5 V, Vin = 1.0 V, VOUT = 0.5 V; 1.6 − 4.9 V, Vin = 1.5 V, VOUT = 0.5 V,
Active Low ‘L’ Suffix Devices
9. Condition 5: 0.9 − 3.9 V, Vin = 4.5 V, VOUT = 2.4 V; 4.0 − 4.9 V, Vin = 8.0 V, VOUT = 5.9 V, Active Low ‘L’ Suffix Devices

Supply Current Pch Source Current
Detector Threshold Nch Sink
NCP300 Series Detector Threshold Hysteresis Vin Low Vin High Current Vin Low Vin High
Iin (mA) Iin (mA) IOUT (mA) IOUT (mA) IOUT (mA)
VDET− (V) (Note 10) VHYS (V) (Note 11) (Note 12) (Note 13) (Note 14) (Note 15)
Part Number Min Typ Max Min Typ Max Typ Typ Typ Typ Typ
NCP300HSN09T1 0.882 0.9 0.918 0.027 0.045 0.063 0.20 0.45 2.5 0.04 0.08
NCP300HSN18T1 1.764 1.8 1.836 0.054 0.090 0.126 0.23 0.48
NCP300HSN27T1 2.646 2.7 2.754 0.081 0.135 0.189 0.25 0.50
NCP300HSN30T1 2.940 3.0 3.060 0.090 0.150 0.210
NCP300HSN45T1 4.410 4.5 4.590 0.135 0.225 0.315 0.33 0.52
NCP300HSN47T1 4.606 4.7 4.794 0.141 0.235 0.329 0.34 0.53
13. Condition 3: 0.9 − 1.4 V, Vin = 1.5 V, VOUT = 0.5 V; 1.5 − 4.9 V, Vin = 5.0 V, VOUT = 0.5 V, Active High ‘H’ Suffix Devices
14. Condition 4: 0.9 − 4.9 V, Vin = 0.7 V, VOUT = 0.4 V, Active High ‘H’ Suffix Devices
15. Condition 5: 0.9 − 1.0 V, Vin = 0.8 V, VOUT = GND; 1.1 − 1.5 V, Vin = 1.0 V, VOUT = GND; 1.6 − 4.9 V, Vin = 1.5 V, VOUT = GND,
Active High ‘H’ Suffix Devices
www.onsemi.com
9
NCP300, NCP301

Supply Current Nch Sink Current
Detector Threshold
NCP301 Series Detector Threshold Hysteresis Vin Low Vin High Vin Low Vin High
Iin (mA) Iin (mA) IOUT (mA) IOUT (mA)
VDET− (V) (Note 16) VHYS (V) (Note 16) (Note 18) (Note 19) (Note 20)
Part Number Min Typ Max Min Typ Max Typ Typ Typ Typ
NCP301LSN09T1 0.882 0.9 0.918 0.027 0.045 0.063 0.20 0.45 0.05 0.5
NCP301LSN12T1 1.176 1.2 1.224 0.036 0.060 0.084
NCP301LSN16T1 1.568 1.6 1.632 0.048 0.080 0.112 2.0
NCP301LSN18T1 1.764 1.8 1.836 0.054 0.090 0.126 0.23 0.48
NCP301LSN20T1 1.960 2.0 2.040 0.060 0.100 0.140
NCP301LSN22T1 2.156 2.2 2.244 0.066 0.110 0.154
NCP301LSN24T1 2.352 2.4 2.448 0.072 0.120 0.168
NCP301LSN25T1 2.450 2.5 2.550 0.075 0.125 0.175
NCP301LSN26T1 2.548 2.6 2.652 0.078 0.130 0.182
NCP301LSN27T1 2.646 2.7 2.754 0.081 0.135 0.189 0.25 0.50
NCP301LSN28T1 2.744 2.8 2.856 0.084 0.140 0.196
NCP301LSN30T1 2.940 3.0 3.060 0.090 0.150 0.210
NCP301LSN31T1 3.038 3.1 3.162 0.093 0.155 0.217
NCP301LSN32T1 3.136 3.2 3.264 0.096 0.160 0.224
NCP301LSN33T1 3.234 3.3 3.366 0.099 0.165 0.231
NCP301LSN34T1 3.332 3.4 3.468 0.102 0.170 0.238
NCP301LSN36T1 3.528 3.6 3.672 0.108 0.180 0.252
NCP301LSN40T1 3.920 4.0 4.080 0.120 0.200 0.280
NCP301LSN42T1 4.116 4.2 4.284 0.126 0.210 0.294
NCP301LSN45T1 4.410 4.5 4.590 0.135 0.225 0.315 0.33 0.52
NCP301LSN46T1 4.508 4.6 4.692 0.138 0.230 0.322
NCP301LSN47T1 4.606 4.7 4.794 0.141 0.235 0.329 0.34 0.53
19. Condition 3: 0.9 − 4.9 V, Vin = 0.7 V, VOUT = 0.05 V, Active Low ‘L’ Suffix Devices
20. Condition 4: 0.9 − 1.0 V, Vin = 0.85 V, VOUT = 0.5 V; 1.1 − 1.5 V, Vin = 1.0 V, VOUT = 0.5 V; 1.6 − 4.9 V, Vin = 1.5 V, VOUT = 0.5 V,
Condition 4: Active Low ‘L’ Suffix Devices
Supply Current
Detector Threshold Nch
NCP301 Series Detector Threshold Hysteresis Vin Low Vin High Sink Current
Iin (mA) Iin (mA) IOUT (mA)
VDET− (V) (Note 21) VHYS (V) (Note 22) (Note 23) (Note 24)
Part Number Min Typ Max Min Typ Max Typ Typ Typ
NCP301HSN09T1 0.882 0.9 0.918 0.027 0.045 0.063 0.20 0.45 2.5
NCP301HSN18T1 1.764 1.8 1.836 0.054 0.090 0.126
NCP301HSN22T1 2.156 2.2 2.244 0.066 0.110 0.154
NCP301HSN27T1 2.646 2.7 2.754 0.081 0.135 0.189 0.25 0.50
NCP301HSN30T1 2.940 3.0 3.060 0.090 0.150 0.210
NCP301HSN45T1 4.410 4.5 4.590 0.135 0.225 0.315 0.33 0.52
21. Values shown apply at +25°C only. For voltage options greater than 1.1 V, VDET− limits over operating temperature range (−40°C to
+125°C) are VNOM ±3%. For voltage options < 1.2 V, VDET− is guaranteed only at +25°C.
24. Condition 3: 0.9 − 1.4 V, Vin = 1.5 V, VOUT = 0.5 V; 1.5 − 4.9 V, Vin = 5.0 V, VOUT = 0.5 V, Active High ‘H’ Suffix Devices
www.onsemi.com
10
NCP300, NCP301
1.0 10.5
TA = 25°C TA = 25°C
0.9
2.5
Iin, INPUT CURRENT (mA)
0.8

0.7
2.0
0.6
0.5 1.5
0.4
0.3 1.0
0.2
0.5
0.1
0 0
0 2.0 4.0 6.0 8.0 10 12 0 2.0 4.0 6.0 8.0 10 12
Vin, INPUT VOLTAGE (V) Vin, INPUT VOLTAGE (V)
Figure 3. NCP300/1 Series 0.9 V Figure 4. NCP300/1 Series 2.7 V

Input Current versus Input Voltage Input Current versus Input Voltage
17.2 1.00
VDET, DETECTOR THRESHOLD VOLTAGE (V)

TA = 25°C
2.5
0.95
VDET+
2.0
1.5 0.90
VDET−
1.0
0.85
0.5
0 0.80
0 2.0 4.0 6.0 8.0 10 12 −50 −25 0 25 50 75 100
Vin, INPUT VOLTAGE (V) TA, AMBIENT TEMPERATURE (°C)

Input Current versus Input Voltage Detector Threshold Voltage versus Temperature
2.90 4.9
2.85 4.8
VDET+ VDET+
2.80 4.7
2.75 4.6
2.70 4.5
VDET−
VDET−
2.65 4.4
2.60 4.3
−50 −25 0 25 50 75 100 125 −50 −25 0 25 50 75 100 125
TA, AMBIENT TEMPERATURE (°C) TA, AMBIENT TEMPERATURE (°C)

Detector Threshold Voltage versus Temperature Detector Threshold Voltage versus Temperature
www.onsemi.com
11
NCP300, NCP301
1.0 3.5
3.0
VOUT, OUTPUT VOLTAGE (V)

0.8
2.5
0.6 2.0
TA = −40°C (301L only) 1.5

0.4
1.0 TA = 125°C (301L only)

TA = 25°C (301L only)
0.2 TA = −40°C (301L only)
0.5
TA = 25°C (301L only)
0 0
0 0.2 0.4 0.6 0.8 1.0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5
Figure 9. NCP300L/1L Series 0.9 V Figure 10. NCP300L/1L Series 2.7 V

Reset Output Voltage versus Input Voltage Reset Output Voltage versus Input Voltage
6.0 1.6
VOUT = 0.5 V
IOUT, OUTPUT SINK CURRENT (mA)

1.4
5.0
TA = −40°C
1.2
4.0
1.0
3.0 0.8
TA = −40°C (301L only) 0.6

2.0
TA = 25°C
TA = 25°C (301L only) 0.4
1.0 TA = 85°C
0.2
0 0
0 1.0 2.0 3.0 4.0 5.0 6.0 0 0.2 0.4 0.6 0.8 1.0
Figure 11. NCP300L/1L Series 4.5 V Figure 12. NCP300H/1L Series 0.9 V
Reset Output Voltage versus Input Voltage Reset Output Sink Current versus Input Voltage
12 20
VOUT = 0.5 V VOUT = 0.5 V
10 TA = −40°C
TA = −40°C
15
8.0
6.0 10
TA = 25°C TA = 25°C
4.0
TA = 125°C TA = 125°C
5.0
2.0
0 0
0 0.5 1.0 1.5 2.0 2.5 3.0 0 1.0 2.0 3.0 4.0 5.0
Figure 13. NCP300H/1L Series 2.7 V Figure 14. NCP300H/1L Series 4.5 V
Reset Output Sink Current versus Input Voltage Reset Output Sink Current versus Input Voltage
www.onsemi.com
12
NCP300, NCP301
20 20
IOUT, OUTPUT SOURCE CURRENT (mA)

TA = 25°C VOUT = Vin −2.1 V TA = 25°C VOUT = Vin −2.1 V
15 15 Vin −1.5 V
Vin −1.5 V Vin −1.0 V

10 10
Vin −1.0 V
Vin −0.5 V
5.0 5.0
Vin −0.5 V
0 0
0 2.0 4.0 6.0 8.0 10 0 2.0 4.0 6.0 8.0 10
Figure 15. NCP300L Series 0.9 V Figure 16. NCP300L Series 2.7 V
Reset Output Source Current versus Input Voltage Reset Output Source Current versus Input Voltage
20 1.5

TA = 25°C VOUT = Vin −2.1 V TA = 25°C
15
1.0 Vin = 0.85 V
Vin −1.5 V
10
Vin −1.0 V
0.5 Vin = 0.7 V
5.0
Vin −0.5 V
0 0
0 2.0 4.0 6.0 8.0 10 0 0.2 0.4 0.6 0.8 1.0
Vin, INPUT VOLTAGE (V) VOUT, OUTPUT VOLTAGE (V)
Figure 17. NCP300L Series 4.5 V Figure 18. NCP300H/1L Series 0.9 V
Reset Output Source Current versus Input Voltage Reset Output Sink Current versus Output Voltage
15 35
TA = 25°C
TA = 25°C
Vin = 2.5 V 30
Vin = 4.0 V
25
10 Vin = 3.5 V
Vin = 2.0 V 20
Vin = 3.0 V
15
5.0 Vin = 2.5 V
10
Vin = 1.5 V
Vin = 2.0 V
5.0
Vin = 1.5 V
0 0
0 0.5 1.0 1.5 2.0 2.5 0 1.0 2.0 3.0 4.0
VOUT, OUTPUT VOLTAGE (V) VOUT, OUTPUT VOLTAGE (V)
Figure 19. NCP300H/1L Series 2.7 V Figure 20. NCP300H/1L Series 4.5 V
Reset Output Sink Current versus Output Voltage Reset Output Sink Current versus Output Voltage
www.onsemi.com
13
NCP300, NCP301
OPERATING DESCRIPTION high state for active high devices. After completion of the
The NCP300 and NCP301 series devices are second power interruption, Vin will again return to its nominal level
generation ultra−low current voltage detectors. Figures 20 and become greater than the VDET+. The voltage detector
and 21 show a timing diagram and a typical application. has built−in hysteresis to prevent erratic reset operation as
Initially consider that input voltage Vin is at a nominal level the comparator threshold is crossed.
and it is greater than the voltage detector upper threshold Although these device series are specifically designed for
(VDET+), and the reset output (Pin 1) will be in the high state use as reset controllers in portable microprocessor based
for active low devices, or in the low state for active high systems, they offer a cost−effective solution in numerous
devices. If there is a power interruption and Vin becomes applications where precise voltage monitoring is required.
significantly deficient, it will fall below the lower detector Figure 26 through Figure 33 shows various application
threshold (VDET−). This sequence of events causes the Reset examples.
output to be in the low state for active low devices, or in the
Vin
Input Voltage, Pin 2
VDET+
VDET−
Vin
Reset Output (Active Low), Pin 1
VDET+
VDET−
0V
Vin
Reset Output (Active High), Pin 1
VDET+
VDET−
0V
Figure 21. Timing Waveforms
www.onsemi.com
14
NCP300, NCP301
VCC TRANSIENT REJECTION FACTORS TO BE CONSIDERED FOR VOLTAGE

The NCP300 and NCP301 series provides accurate VCC OPTION SELECTION
monitoring and reset timing during power−up, The following hysteresis graph depicts VDET−_min/max
power−down, and brownout/sag conditions, and rejects and VDET+_min/max for an active low Reset device:
negative glitches on the power supply line. Figure 22 shows
the maximum transient duration vs. maximum negative Output
VDET−_typ
excursion (overdrive) for glitch rejection. Any combination
of duration and overdrive which lies under the curve will not
generate a reset signal. A below−VCC condition (on the
right) is detected as a brownout or power−down. Typically,
any transient that goes 100 mV below the reset threshold and
lasts 5.0 ms or less will not cause a reset pulse. VDET−_min VDET−_max VDET+_min VDET+_max
Transient immunity can be improved by adding a
capacitor in close proximity to the VCC pin of the NCP30x. Input
VCC VDET+_min = VDET−_min + VHYS_min

VTH VDET+_max = VDET−_max + VHYS_max
Overdrive
Figure 24.
For selecting a voltage option in the NCP30X family,

Duration
three major factors should be considered:
1. VDET+_max: Maximum detector threshold voltage
Figure 22. Max Transient Duration vs. Max Overdrive
for increasing Vin for the NCP30X device.
2. Vin_min: Minimum voltage output of the power
supply. This is also the input voltage to the
300
NCP30X device.
250
3. VCC_min: Minimum power supply voltage
specification for the device that is protected by the
TRANSIENT DURATION
200
NCP30X.
The VDET+_max for an NCP30X device is normally
VTH = 4.90 V
calculated as follows:
150
VTH = 3.10 V V DET+_max + V DET−_max ) V HYS_max (eq. 1)
100 VTH = 1.60 V
Where:
VDET−_max = Maximum detector threshold voltage for
50
decreasing Vin
0
VHYS_max = Maximum detector threshold hysteresis
10 30 50 70 90 110 130 150 The above two parameters can be obtained directly from
RESET COMPARATOR OVERDRIVE the data sheet to figure out the VDET+_max.
In the NCP30X family, for a given VDET−_typ, which is the
Figure 23. typical detection voltage reflected in the part number, the
threshold values are designed to the following targets (at
25°C):
V DET−_min + V DET−_typ * 2% (eq. 2)
V DET−_max + V DET−_typ ) 2% (eq. 3)
V HYS_typ + 5% of V DET−_typ (eq. 4)
V HYS_min + V HYS_typ * 40% (eq. 5)
V HYS_max + V HYS_typ ) 40% (eq. 6)
By simple mathematical calculation, combining

Equations 2 to 6, Equation 1 becomes:
V DET+_max + V DET−_typ 1.09 (eq. 7)
www.onsemi.com
15
NCP300, NCP301
So, VDET+_max can be easily figured out just using a single PROPAGATION DELAY VARIATION
variable VDET−_typ. On the other hand (see above paragraph), a minimum
For example, for NCP300LSN18T1G VDET−_typ = 1.8 V; overdrive value from Vthreshold to VCC must be respected.
then That means Vin (minimum value of VCC) must be higher
enough than VDET+ (VDET− + hysteresis) at the risk of
V DET+_max + 1.8 1.09 + 1.962 V (eq. 8)
significantly increasing propagation delay. (Figure 25) This
The NCP30X detection voltage option must be chosen such propagation delay is temperature sensitive.
that: To avoid acceptable time response, a minimum 100 mV
V CC_min t V DET+_max t V in_min difference between Vin and VDET+ must be selected.
(eq. 9)
The significance of VCC_min < VDET+_max is that it makes VDET+
sure the the reset from NCP30X remains asserted (in RESET 600
hold state) till after the power supply exceeds the VCC_min
requirement; this prevents incorrect device (uP) initiation. 500
Having VDET+_max < Vin_min makes sure that the
TIME DELAY (ms)

NCP30X is able to start up when Vin is at the Vin_min. 400
The theoretical ideal VDET−_typ voltage option to be
selected by the user, VDET−_typ_ideal, can be given by the 300
tpLH
following formula:
ǒVin_min ) VCC_minǓ 200
(eq. 10)
V DET−_typ_ideal + tpHL
(2 1.09) 100
The following example shows how to select the device 0
voltage option in a real world application. 3.0 3.5 4.0 4.5 5.0 5.5
1. Power supply output specification: 3.3 V $3% 3.168
2. Microprocessor core voltage specification: 3.3 V Vin, PULSE HIGH INPUT VOLTAGE (V)
$5%
So, we have: Figure 25. tpLH and tpHL vs. Input Voltage
for the NCP301SNT1
V in_min + 3.3 V * 3% + 3.201 V (eq. 11)
V CC_min + 3.3 V * 5% + 3.135 V (eq. 12)
Then the ideal voltage option = (3.201 + 3.135) / (2 * 1.09)

= 2.9064 V
Therefore, a device voltage option of 2.9 V will be the right
choice.
www.onsemi.com
16
NCP300, NCP301
APPLICATION CIRCUIT INFORMATION
VDD
VDD
2 Input *
NCP300 1
Microprocessor
Series
Reset Output Reset
3 GND * Required for

NCP301 GND
Figure 26. Microprocessor Reset Circuit
2.85 V
2.70 V
Vin < 2.7 ON
2 Input
NCP300 1
LSN27T1 To Additional Circuitry
Reset Output
Vin > 2.835 ON
3 GND
Figure 27. Battery Charge Indicator
Vsupply
10 V Fault
Active High 2 Input

Device Thresholds
Active Low UV 1
Device Thresholds NCP301
LSN23T1 Reset Output
1.0 V UV OV OV UV
Fault OK Fault Fault OK Fault 3 GND
Input
The above circuit combines an active high and an active low reset output device to form 2 Input
a window detector for monitoring battery or power supply voltages. When the input
voltage falls outside of the window established by the upper and lower device OV 1 Output
thresholds, the LED will turn on indicating a fault. As the input voltage falls within the NCP301
window, increasing from 1.0 V and exceeding the active low device’s hysteresis HSN43T1 Reset Output
threshold, or decreasing from the peak towards 1.0 V and falling below the active high
device’s undervoltage threshold, the LED will turn off. The device thresholds shown can
be used for a single cell lithium−ion battery charge detector. 3 GND
Figure 28. Window Voltage Detector
www.onsemi.com
17
NCP300, NCP301
APPLICATION CIRCUIT INFORMATION
Vsupply
5.0 V
2 Input
1
NCP301
LSN45T1 Reset Output
3 GND
3.3 V
2 Input
1
NCP301 Low state output if either power
LSN30T1 Reset Output supply is below the respective
undervoltage detector threshold
3 GND but greater than 1.0 V.
Figure 29. Dual Power Supply Undervoltage Supervision
VDD
RH
2 Input VDD
RL
1
NCP301
Microprocessor
LSN27T1 Reset Output Reset
3 GND GND
Figure 30. Microprocessor Reset Circuit with Additional Hysteresis
Comparator hysteresis can be increased with the addition of Test Data

resistor RH. The hysteresis equations have been simplified and
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
do not account for the change of input current Iin as Vin crosses Vth Decreasing Vth Increasing VHYS RH RL
the comparator threshold. The internal resistance, Rin is simply (V) (V) (V) (W) (kW)
calculated using Iin = 0.26 mA at 2.6 V.
2.70 2.84 0.135 0 −
Vin Decreasing: 2.70 2.87 0.17 100 10
ǒRR Ǔ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
2.70 2.88 0.18 100 6.8
V th + H
) 1 ǒV DET*Ǔ 2.70 2.91 0.21 100 4.3
ÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁ
ÁÁÁÁÁ
in 2.70 2.90 0.20 220 10
ÁÁ
2.70 2.94 0.24 220 6.8
Vin Increasing: 2.70 2.98 0.28 220 4.3
V th + ǒ RH
Ǔ
) 1 ǒV DET* ) V HYSǓ
2.70
2.70
2.97
3.04
0.27
0.34
470
470
10
6.8
R in ø R L 2.70 3.15 0.45 470 4.3
VHYS = Vin Increasing − Vin Decreasing
www.onsemi.com
18
NCP300, NCP301
5.0 V
Test Data
R2 = 82 kW R2 = 8.2 kW
R1 = 100 kW
C (nF) fOSC (kHz) IQ (mA) fOSC (kHz) IQ (mA)
0.01 10.4 18 6.0 30
0.068 9.8 18 5.7 30
2 Input
R2 (See table) 1.0 6.18 21 3.6 29
1 10 1.41 21 1.34 25
C NCP301
NCP300
HSN27T1
LSN27T1 Reset Output 100 0.27 22 0.356 23
3 GND 1000 0.045 22 0.077 22

Table values are for information only.
Figure 31. Simple Clock Oscillator
Vsupply
This circuit monitors the current at the load. As
current flows through the load, a voltage drop with
Load respect to ground appears across Rsense where
VDD Vsense = Iload * Rsense. The following conditions apply:
If: Then:
2 Input ILoad t VDET − /Rsense Reset Output = 0 V
Rsense
50 k ILoad w (VDET −+VHYS)/Rsense Reset Output = VDD
NCP301 1
Microcontroller
LSN09T1
LSN27T1
Reset Output
3 GND GND
Figure 32. Microcontroller System Load Sensing
www.onsemi.com
19
NCP300, NCP301
Vsupply
2 Input
1
NCP301
LSN27T1
LSN45T1 Reset
Output
3 GND
2 Input
1
NCP301
LSN27T1 Reset
Output
3 GND
Vin = 1.0 V to 10 V
2 Input
1
NCP301
LSN27T1
LSN18T1
Reset
Output
3 GND
A simple voltage monitor can be constructed by connecting several voltage detectors as shown above. Each LED will
sequentially turn on when the respective voltage detector threshold (VDET− +VHYS) is exceeded. Note that detector
thresholds (VDET−) that range from 0.9 V to 4.9 V in 100 mV steps can be manufactured.
Figure 33. LED Bar Graph Voltage Monitor
www.onsemi.com
20
NCP300, NCP301
ORDERING INFORMATION
Device Threshold Voltage Output Type Reset Marking Package Shipping†
NCP300LSN09T1G 0.9 SEJ TSOP−5
(Pb−Free)
NCP300LSN18T1G 1.8 SFK TSOP−5
(Pb−Free)
NCP300LSN185T1G 1.85 SRA TSOP−5
(Pb−Free)
NCP300LSN20T1G 2.0 SHE TSOP−5
NCV300LSN20T1G* SIM (Pb−Free)
NCP300LSN25T1G 2.5 TSOP−5
RUM
(Pb−Free)
NCP300LSN27T1G 2.7 SEE TSOP−5
NCV300LSN27T1G* SIW (Pb−Free)
NCP300LSN28T1G 2.8 SED TSOP−5
NCV300LSN28T1G* Active SSL (Pb−Free) 3000 / Tape & Reel
CMOS
NCP300LSN30T1G 3.0 Low SEC TSOP−5 (7 in. Reel)
NCV300LSN30T1G* SQV (Pb−Free)
NCP300LSN33T1G 3.3 SKV TSOP−5
(Pb−Free)
NCP300LSN34T1G 3.4 SKU TSOP−5
NCV300LSN36T1G* 3.6 SKS (Pb−Free)
NCP300LSN44T1G 4.4 SKK TSOP−5
(Pb−Free)
NCP300LSN45T1G 4.5 SEA TSOP−5
(Pb−Free)
NCP300LSN46T1G 4.6 SKJ TSOP−5
(Pb−Free)
NCP300LSN47T1G 4.7 SDZ TSOP−5
(Pb−Free)
NCP300HSN09T1G 0.9 SDY TSOP−5
(Pb−Free)
NCP300HSN18T1G 1.8 SFJ TSOP−5
(Pb−Free)
NCP300HSN27T1G 2.7 SDU TSOP−5
Active (Pb−Free) 3000 / Tape & Reel
CMOS
NCP300HSN30T1G 3.0 High SDS TSOP−5 (7 in. Reel)
(Pb−Free)
NCP300HSN45T1G 4.5 SDQ TSOP−5
(Pb−Free)
NCP300HSN47T1G 4.7 SDP TSOP−5
(Pb−Free)
NOTE: The ordering information lists standard undervoltage thresholds with active low outputs. Additional active low threshold devices,
ranging from 0.9 V to 4.9 V in 100 mV increments and NCP300/NCP301 active high output devices, ranging from 0.9 V to 4.9 V
in 100 mV increments can be manufactured. Contact your ON Semiconductor representative for availability. The electrical
characteristics of these additional devices are shown in Tables 1 through 4.
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Spe-
cifications Brochure, BRD8011/D.
*NCV prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP
Capable.
NCVxxx: Tlow = −40°C, Thigh = +125°C. Guaranteed by design.
www.onsemi.com
21
NCP300, NCP301
NCP301LSN09T1G 0.9 SFF TSOP−5
(Pb−Free)
NCP301LSN12T1G 1.2 SNN TSOP−5
(Pb−Free)
NCV301LSN12T1* SRK TSOP−5
NCV301LSN12T1G* TSOP−5
(Pb−Free)
NCP301LSN16T1G 1.6 SNJ TSOP−5
(Pb−Free)
NCV301LSN16T1* SRL TSOP−5
(Pb−Free)
NCP301LSN18T1G 1.8 SFN TSOP−5
(Pb−Free)
NCP301LSN18T2G DT2 TSOP−5
(Pb−Free)
NCP301LSN20T1G 2.0 SFD TSOP−5
NCV301LSN20T1G* SRM (Pb−Free)
NCP301LSN22T1G 2.2 SNG TSOP−5
(Pb−Free)
NCV301LSN22T1* SUA TSOP−5
(Pb−Free)
NCP301LSN24T1G 2.4 TAN TSOP−5
(Pb−Free)
Open Active 3000 / Tape & Reel
NCP301LSN25T1G 2.5 Drain Low SNF TSOP−5 (7 in. Reel)
(Pb−Free)
NCP301LSN25T2G ET2 TSOP−5
(Pb−Free)
NCV301LSN25T1G* SRN TSOP−5
(Pb−Free)
NCP301LSN26T1G 2.6 SNE TSOP−5
(Pb−Free)
NCP301LSN27T1G 2.7 SFA TSOP−5
(Pb−Free)
NCP301LSN27T2G FT2 TSOP−5
(Pb−Free)
NCP301LSN28T1G 2.8 SEZ TSOP−5
(Pb−Free)
NCV301LSN28T1G* SRO TSOP−5
(Pb−Free)
NCP301LSN30T1G 3.0 SEY TSOP−5
(Pb−Free)
NCP301LSN30T2G GT2 TSOP−5
(Pb−Free)
NCV301LSN30T1G* AJA TSOP−5
(Pb−Free)
NCP301LSN31T1G 3.1 SEW TSOP−5
(Pb−Free)
NCP301LSN32T1G 3.2 SNC TSOP−5
(Pb−Free)
Capable.
www.onsemi.com
22
NCP300, NCP301
NCP301LSN33T1G 3.3 SNB TSOP−5
(Pb−Free)
NCV301LSN33T1G* ACG TSOP−5
(Pb−Free)
NCP301LSN34T1G 3.4 SNA TSOP−5
NCP301LSN36T1G 3.6 SMY (Pb−Free)
NCP301LSN39T1G 3.9 SNA
NCP301LSN40T1G 4.0 SMU TSOP−5
(Pb−Free)
NCV301LSN40T1* Open Active SRP TSOP−5 3000 / Tape & Reel
NCV301LSN40T1G* Drain Low TSOP−5 (7 in. Reel)
(Pb−Free)
NCP301LSN42T1G 4.2 SMS TSOP−5
NCV301LSN42T1G* ACR (Pb−Free)
NCP301LSN45T1G 4.5 SEV TSOP−5
NCV301LSN45T1G* SRQ (Pb−Free)
NCP301LSN46T1G 4.6 SMP TSOP−5
(Pb−Free)
NCP301LSN47T1G 4.7 SEU TSOP−5
NCV301LSN47T1G* SSJ (Pb−Free)
Capable.
www.onsemi.com
23
NCP300, NCP301
NCP301HSN09T1G 0.9 SET TSOP−5
(Pb−Free)
NCP301HSN18T1G 1.8 SFM TSOP−5
(Pb−Free)
NCP301HSN22T1G 2.2 SMD TSOP−5
(Pb−Free)
Open Active 3000 / Tape & Reel
NCP301HSN27T1G 2.7 Drain High SEP TSOP−5 (7 in. Reel)
(Pb−Free)
NCV301HSN27T1G* SUD
NCP301HSN30T1G 3.0 SEN TSOP−5
(Pb−Free)
NCP301HSN45T1G 4.5 SEL TSOP−5
(Pb−Free)
Capable.
www.onsemi.com
24
MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
TSOP−5
CASE 483
5 ISSUE N
1 DATE 12 AUG 2020
SCALE 2:1
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
NOTE 5 D 5X Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
0.20 C A B 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH
2X 0.10 T THICKNESS. MINIMUM LEAD THICKNESS IS THE
MINIMUM THICKNESS OF BASE MATERIAL.
M 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD
5 4 FLASH, PROTRUSIONS, OR GATE BURRS. MOLD
2X 0.20 T S
B FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT
1 2 3 EXCEED 0.15 PER SIDE. DIMENSION A.
K 5. OPTIONAL CONSTRUCTION: AN ADDITIONAL
B TRIMMED LEAD IS ALLOWED IN THIS LOCATION.
G DETAIL Z
TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2
FROM BODY.
A A
MILLIMETERS
TOP VIEW DIM MIN MAX
A 2.85 3.15
B 1.35 1.65
DETAIL Z C 0.90 1.10
J D 0.25 0.50
G 0.95 BSC
C H 0.01 0.10
0.05 J 0.10 0.26
H SEATING K 0.20 0.60
C PLANE
END VIEW M 0_ 10 _
SIDE VIEW S 2.50 3.00
GENERIC
SOLDERING FOOTPRINT*
MARKING DIAGRAM*
1.9
0.074 5 5
0.95
0.037 XXXAYWG XXX MG
G G
1 1
Analog Discrete/Logic
2.4 XXX = Specific Device Code XXX = Specific Device Code

0.094 A = Assembly Location M = Date Code
Y = Year G = Pb−Free Package
1.0 W = Work Week
0.039 G = Pb−Free Package
(Note: Microdot may be in either location)
0.7 *This information is generic. Please refer to
0.028 SCALE 10:1 ǒinches
mm Ǔ
device data sheet for actual part marking.
Pb−Free indicator, “G” or microdot “ G”,
*For additional information on our Pb−Free strategy and soldering may or may not be present.
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
Electronic versions are uncontrolled except when accessed directly from the Document Repository.
DOCUMENT NUMBER: 98ARB18753C Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.
DESCRIPTION: TSOP−5 PAGE 1 OF 1
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the
rights of others.
© Semiconductor Components Industries, LLC, 2018 www.onsemi.com

onsemi, , and other names, marks, and brands are registered and/or common law trademarks of Semiconductor Components Industries, LLC dba “onsemi” or its affiliates
and/or subsidiaries in the United States and/or other countries. onsemi owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property.
A listing of onsemi’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. onsemi reserves the right to make changes at any time to any
products or information herein, without notice. The information herein is provided “as−is” and onsemi makes no warranty, representation or guarantee regarding the accuracy of the
information, product features, availability, functionality, or suitability of its products for any particular purpose, nor does onsemi assume any liability arising out of the application or use
of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products
and applications using onsemi products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information
provided by onsemi. “Typical” parameters which may be provided in onsemi data sheets and/or specifications can and do vary in different applications and actual performance may
vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. onsemi does not convey any license
under any of its intellectual property rights nor the rights of others. onsemi products are not designed, intended, or authorized for use as a critical component in life support systems
or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should
Buyer purchase or use onsemi products for any such unintended or unauthorized application, Buyer shall indemnify and hold onsemi and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that onsemi was negligent regarding the design or manufacture of the part. onsemi is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION

LITERATURE FULFILLMENT: TECHNICAL SUPPORT
Email Requests to: [email protected] North American Technical Support: Europe, Middle East and Africa Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada Phone: 00421 33 790 2910
onsemi Website: www.onsemi.com Phone: 011 421 33 790 2910 For additional information, please contact your local Sales Representative

ncp300 D

Uploaded by

Copyright:

Available Formats

ncp300 D

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ncp300 D

Uploaded by

Copyright:

Available Formats

NCP300, NCP301

Voltage Detector Series

• Specified Over the −40°C to +125°C Temperature Range Input 2

Figure 1. Representative Block Diagrams

© Semiconductor Components Industries, LLC, 2016 1 Publication Order Number:

3. Maximum ratings per JEDEC standard JESD78.

NCP300/1 − 1.8 / NCV300/1 − 1.8

NCP300/1 − 2.0 / NCV300/1 − 2.0

NCP300/1 − 2.2 / NCV300/1 − 2.2

NCP300/1− 2.7 / NCV300/1− 2.7

NCP300/1− 2.8 / NCV300/1− 2.8

NCP300/1 − 3.0 / NCV300/1 − 3.0

NCP300/1 − 4.5 / NCV300/1 − 4.5

NCP300/1 − 4.7 / NCV300/1 − 4.7

Input Voltage, Pin 2

Reset Output Voltage, Pin 1

Reset Output Voltage, Pin 1 VDET+ + 2

Figure 2. Propagation Delay Measurement Conditions

Table 1. ELECTRICAL CHARACTERISTIC TABLE FOR 0.9 − 4.9 V

Table 2. ELECTRICAL CHARACTERISTIC TABLE FOR 0.9 − 4.9 V

Table 3. ELECTRICAL CHARACTERISTIC TABLE FOR 0.9 − 4.9 V

Iin, INPUT CURRENT (mA)

Figure 3. NCP300/1 Series 0.9 V Figure 4. NCP300/1 Series 2.7 V

VDET, DETECTOR THRESHOLD VOLTAGE (V)

Figure 5. NCP300/1 Series 4.5 V Figure 6. NCP300/1 Series 0.9 V

VDET, DETECTOR THRESHOLD VOLTAGE (V)

Figure 7. NCP300/1 Series 2.7 V Figure 8. NCP300/1 Series 4.5 V

VOUT, OUTPUT VOLTAGE (V)

TA = −40°C (301L only) 1.5

1.0 TA = 125°C (301L only)

Figure 9. NCP300L/1L Series 0.9 V Figure 10. NCP300L/1L Series 2.7 V

IOUT, OUTPUT SINK CURRENT (mA)

TA = −40°C (301L only) 0.6

IOUT, OUTPUT SINK CURRENT (mA)

IOUT, OUTPUT SOURCE CURRENT (mA)

Vin −1.5 V Vin −1.0 V

IOUT, OUTPUT SINK CURRENT (mA)

Figure 21. Timing Waveforms

VCC TRANSIENT REJECTION FACTORS TO BE CONSIDERED FOR VOLTAGE

VCC VDET+_min = VDET−_min + VHYS_min

For selecting a voltage option in the NCP30X family,

V DET−_max + V DET−_typ ) 2% (eq. 3)

V HYS_typ + 5% of V DET−_typ (eq. 4)

V HYS_min + V HYS_typ * 40% (eq. 5)

V HYS_max + V HYS_typ ) 40% (eq. 6)

By simple mathematical calculation, combining

TIME DELAY (ms)

V CC_min + 3.3 V * 5% + 3.135 V (eq. 12)

Then the ideal voltage option = (3.201 + 3.135) / (2 * 1.09)

APPLICATION CIRCUIT INFORMATION

3 GND * Required for

Figure 26. Microprocessor Reset Circuit

Figure 27. Battery Charge Indicator

Active High 2 Input

Figure 28. Window Voltage Detector

APPLICATION CIRCUIT INFORMATION

Figure 29. Dual Power Supply Undervoltage Supervision

Figure 30. Microprocessor Reset Circuit with Additional Hysteresis

Comparator hysteresis can be increased with the addition of Test Data