Scribd Logo
Upload

Welcome to Scribd!

  • 17 views

    Cavity Instructions 2016

    Uploaded by

    James Gravey
    This document contains installation instructions for an Evolution Cavity Unit. It provides instructions on assembling the cavity unit which involves installing the top track section, closing jamb, lifting the cavity into place and securing it, and inserting and adjusting the doors. Diagrams show attaching the wheel assembly and bumper stop to the doors and installing a double bump stop for double cavity units. The final step is attaching pre-cut pelmet timbers.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Cavity Instructions 2016

    Uploaded by

    James Gravey
    17 views2 pages
    This document contains installation instructions for an Evolution Cavity Unit. It provides instructions on assembling the cavity unit which involves installing the top track section, closing jamb, lifting the cavity into place and securing it, and inserting and adjusting the doors. Diagrams show attaching the wheel assembly and bumper stop to the doors and installing a double bump stop for double cavity units. The final step is attaching pre-cut pelmet timbers.

    Original Title

    CAVITY-INSTRUCTIONS-2016 (1)

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document contains installation instructions for an Evolution Cavity Unit. It provides instructions on assembling the cavity unit which involves installing the top track section, closing jamb, lifting the cavity into place and securing it, and inserting and adjusting the doors. Diagrams show attaching the wheel assembly and bumper stop to the doors and installing a double bump stop for double cavity units. The final step is attaching pre-cut pelmet timbers.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    17 views2 pages

    Cavity Instructions 2016

    Uploaded by

    James Gravey
    This document contains installation instructions for an Evolution Cavity Unit. It provides instructions on assembling the cavity unit which involves installing the top track section, closing jamb, lifting the cavity into place and securing it, and inserting and adjusting the doors. Diagrams show attaching the wheel assembly and bumper stop to the doors and installing a double bump stop for double cavity units. The final step is attaching pre-cut pelmet timbers.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    EVOLUTION

    CAVITY UNIT
    70kg

    Installation
    Instructions
    TRIM AUCKLAND
    TRIM 77 Plunket Ave
    HEIGHT
    HEIGHT Manukau, N.Z.
    P.O. Box 76698, Manukau,2241
    Ph (09)2774509
    Fax (09)2770798

    CHRISTCHURCH
    26 Hammersmith Dve.
    TRIM WIDTH TRIM WIDTH Wigram, Christchurch, N.Z.
    Ph (03)3431555
    Fax (03)3431556
    Assembly Instructions
    1. Ensure that the opening is the correct 6. Attach base plate of wheel assembly to 8. For double cavity only, slide double
    size, to suit the cavity unit being both sides of door 80mm in, keeping bump stop into track approximately 80mm
    installed (including wall thickness), both nylon lock tabs on the same side. either side of of the two meeting tracks,
    also check the opening is plumb and adjust to suit doors.
    and square. Refer table overleaf Attach bumper stop to the center of the
    back edge of door, equally space between
    the top and the bottom of door.
    2. Fit and screw top track section to top
    nogs of cavity. With 65mm screws provided Wheel assembly

    Double bump stop

    Bumper stop

    Base plate
    9. Attach pre cut pelmet timbers to the
    fully installed single cavity or double
    cavity as per diagram below.

    3. Fit and screw closing jamb to track


    section. With 45mm screws provided
    80 mm
    SINGLE CAVITY

    7. Insert door into cavity unit and tilt up


    until adjusting bolt of the hanger
    will slide into the seat of the door plate.
    4. Lift cavity into opening, check the unit is Lock into place with nylon lock tabs.
    plumb and square, ensure the track is
    level. Lift front edge of door and slide the
    other hanger into the remaining
    5. Fix cavity securely to the floor and studs door plate and lock into place. Pre cut pelmet timber
    check again for plumb and square.
    The top track section does not need to be Use wrench provided to raise or lower DOUBLE CAVITY
    fixed to the lintel. hanger to plumb door to jamb. (Bi - parting)

    You might also like