Rotork Manpower

The Rotork manPOWER range provides high-
integrity fail-safe valve operation without the

need for any external power supply. The self-
contained system is suitable for workshop or
field mounting on a wide range of rotary and
linear operated valves and dampers. It offers a
cost-effective solution for actuator applications
where operation is infrequent. Typical applications
include emergency shutdown valves and over-
or under-pressure protection at remote,
unpowered locations.
Each manPOWER module contains a compact manually

operated hydraulic power unit that provides hydraulic pressure
to operate a spring-return actuator. The fail-safe system can
be controlled by electrical control signal(s), pressure pilots or
fire sensors. When tripped, the actuator spring cartridge drives
the valve to its fail-safe position. The safe and easy-to-operate
system is manually recharged via the hand pump. There are
four power module variants. Rotork installs the appropriate
model on an actuator sized to meet the end user’s valve
torque demand. Modular construction from our standard
components facilitates quick delivery and simplifies installation,
operation and maintenance. Configurations are available for manPOWER Range
virtually any size or type of valve.
Fail-Safe Actuator Control System for
manPOWER is easy to mount on either new or existing Quarter-Turn and Linear Valves and Dampers
valve actuators or dampers. The closed-loop, non-breathing
hydraulic circuit is temperature compensated for use in the
most extreme environments. It is also compatible with FDA
approved food grade hydraulic fluids. Installation costs are
reduced because the need for plant air, fuel gas, electricity or
expensive nitrogen backup systems is eliminated.
Optional Features
Key Standard Features • Local electrical controls.
• Completely self contained. • Remote mounted stainless-steel power module enclosure.
• Adaptable for quarter-turn or linear service. • Lockable stainless-steel power module enclosure.
• Simplified control circuit with a minimum of components. • Adjustable speed control.
• Built-in temperature compensation. • High- and/or low-pressure pilot(s).
• High-pressure zero-leakage control system. • High-temperature fire sensor(s).
• Watertight or explosionproof construction. • High-volume rotary pump for large actuators.
• Fail open or closed. • Adaptable for use with SCADA systems.
• High-integrity stainless-steel tube and fittings.
• Manual reset after operation.
• 10 Bar (150 psi) or 100 Bar (1,500 psi) operating pressure
suitable for actuator displacements up to 13.2 L (3.5 US gal).
Redefining Flow Control

General Specifications
Maximum Pressure Maximum Actuator Pump Displacement Flow Capacity1

Model
(Bar/PSI) Displacement (Litres/US gal) (cm3/inch3) (LPM/US GPM)
MPL-1 10 / 150 3.78 / 1.0 21.3 / 1.3 18.9 / 5
MPL-2 10 / 150 7.56 / 2.0 21.3 / 1.3 18.9 / 5
MPH-1 100 / 1,500 3.78 / 1.0 10.65 / 0.65 18.9 / 5

MPH-22 100 / 1,500 13.23 / 3.5 14.75 / 0.90 18.9 / 5
1. The stated flow capacity is the unrestricted flow from the Temperature range:
actuator through the manPOWER control module to the
Standard: -20 to +60 ºC (-5 to +140 ºF)
reservoir. This governs the maximum speed of the actuator
fail mode. Optional low: -46 to +60 ºC (-50 to +140 ºF)
2. This option requires the high-volume pump/reservoir Solenoids: 12V, 24V or 120V to FM, IEC ATEX
assembly that is part of the lockable stainless-steel
Stainless-steel pipeline pressure sensors for high and low ranges
enclosure option.
available to end-user stated set points.
Fusible link eutectic element to the following set temperatures:
70, 95, 124, 138 °C (158, 203, 255, 281 °F).
High-flow dump valve for high-speed fail mode.
Hydraulic System Schematic
The design and disclosure contained in the drawing are the exclusive property of
Rotork. It is furnished as vendor information only, and is not authorisation or licence
to fabricate product. This drawing is not to be copied or reproduced in any form
without express written permission from Rotork.
Redefining Flow Control

manPOWER Range
Fail-Safe Actuator Control System for
Quarter-Turn and Linear Valves and Dampers
Typically Equipped MPH-1
Accumulator Hand Pump

High Pressure Pilot Pressure
Pipeline Sensor* Valve Regulator Relief Valve
Low Pressure
Pipeline Sensor*
Hydraulic
Spring-Return
Actuator
Low Pressure Gauge
High Pressure Gauge

Oil Filler Cap
Latch Valve
Typical MPH-2 Controls
Hydraulic
Level Gauge
System Pressure
Gauge
Rotary High-Volume
Hydraulic Pump
Electrical
Junction Box *
(With Solenoid)
Sealed Stainless-Steel
Hydraulic Reservoir
Auto/Manual Speed Controls
Selector Valve
* Indicates optional equipment

Distributed by | Distribuido por :
[email protected]
WWW.ANYTHINGFLOWS.COM
Flow Control , our passion ®
Life Flows on ™
TM
SCAN ME

Rotork Manpower

Uploaded by

Copyright:

Available Formats

Rotork Manpower

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Rotork Manpower

Uploaded by

Copyright:

Available Formats

The Rotork manPOWER range provides high-

integrity fail-safe valve operation without the

Each manPOWER module contains a compact manually

Redefining Flow Control

Maximum Pressure Maximum Actuator Pump Displacement Flow Capacity1

MPL-1 10 / 150 3.78 / 1.0 21.3 / 1.3 18.9 / 5

MPL-2 10 / 150 7.56 / 2.0 21.3 / 1.3 18.9 / 5

MPH-1 100 / 1,500 3.78 / 1.0 10.65 / 0.65 18.9 / 5

Redefining Flow Control

Typically Equipped MPH-1

Accumulator Hand Pump

Low Pressure Gauge

High Pressure Gauge

Typical MPH-2 Controls

* Indicates optional equipment

Flow Control , our passion ®

You might also like