0% found this document useful (0 votes)
22 views4 pages

Router

The document outlines router configuration steps including: setting the hostname to R1, configuring passwords, generating an RSA key, enabling SSH, configuring console and vty lines, adding IP addresses to GigabitEthernet and Loopback interfaces, and copying the running configuration to startup.

Uploaded by

Kevin Hoag
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
22 views4 pages

Router

The document outlines router configuration steps including: setting the hostname to R1, configuring passwords, generating an RSA key, enabling SSH, configuring console and vty lines, adding IP addresses to GigabitEthernet and Loopback interfaces, and copying the running configuration to startup.

Uploaded by

Kevin Hoag
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Router>enable

Router#conf t
Router#conf terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname R1
R1(config)#ip dom
R1(config)#ip domain-name ccna-lab.com
R1(config)#serv
R1(config)#service pass
R1(config)#service password-encryption
R1(config)#secu
R1(config)#security password min
R1(config)#security password min-length 12
R1(config)#usern
R1(config)#username SSHadmin sec
R1(config)#username SSHadmin secret 55Hadm!n2020
R1(config)#encr
R1(config)#cry
R1(config)#crypto key g
R1(config)#crypto key generate rsa ge
R1(config)#crypto key generate rsa general-keys m
R1(config)#crypto key generate rsa general-keys modulus 1024
The name for the keys will be: R1.ccna-lab.com

% The key modulus size is 1024 bits


% Generating 1024 bit RSA keys, keys will be non-exportable...[OK]
*Mar 1 0:10:37.147: %SSH-5-ENABLED: SSH 1.99 has been enabled
R1(config)#enabl
R1(config)#enable se
R1(config)#enable secret $cisco!PRIV*
R1(config)#line conso
R1(config)#line console 0
R1(config-line)#password $cisco
R1(config-line)#password $cisco!!CON*
R1(config-line)#exe
R1(config-line)#exec-timeout 4 0
R1(config-line)#login
R1(config-line)#exit
R1(config)#line vty 0 15
R1(config-line)#pas
R1(config-line)#password $cisco!!VTY*
R1(config-line)#trans
R1(config-line)#transport in
R1(config-line)#transport input ssh
R1(config-line)#exec-timeout 4 0
R1(config-line)#login local
R1(config-line)#exit
R1(config)#banner m
R1(config)#banner motd /Unathorized Access is Prohibirted/
R1(config)#ipv6 u
R1(config)#ipv6 unicast-routing
R1(config)#int g0
R1(config)#int g0/0/0
R1(config-if)#desc
R1(config-if)#description connection to Server
R1(config-if)#ip address 192.168.0.1 255..255.255.0
^
% Invalid input detected at '^' marker.
R1(config-if)#ip address 192.168.0.1 255.255.255.0
R1(config-if)#ipv6 ad
R1(config-if)#ipv6 address 2001:db8:acad::1/64
R1(config-if)#ipv6 address fe80::1 li
R1(config-if)#ipv6 address fe80::1 link-local
R1(config-if)#no shutd
R1(config-if)#no shutdown

R1(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0/0, changed state to


up

R1(config-if)#int g0/0/1
R1(config-if)#description connection to S1
R1(config-if)#ip address 192.168.1.1 255.255.255.0
R1(config-if)#ipv6 address 2001:db8:acad:1::1/64
R1(config-if)#ipv6 address fe80::1 link-local
R1(config-if)#no shutdown

R1(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0/1, changed state to


up

R1(config-if)#ipv6 address fe80::1 link-local


R1(config-if)#no shutdown
R1(config-if)#ipv6 address 2001:db8:acad:1::1/64
R1(config-if)#no shutdown
R1(config-if)#int lo
R1(config-if)#int loopback 0
R1(config-if)#
%LINK-5-CHANGED: Interface Loopback0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback0, changed state to up

R1(config-if)#description Loopback
R1(config-if)#ip ad
R1(config-if)#ip address 10.0.0.1 255.255.255.0
R1(config-if)#ipv6 address 2001:db8:acad:2::1/64
R1(config-if)#ipv6 address fe80::1 link-local
R1(config-if)#exit
R1(config)#login boc
R1(config)#login bloc
R1(config)#login block-for 120 at
R1(config)#login block-for 120 attempts 3 within 60
R1(config)#

R1#clock set ?
hh:mm:ss Current Time
R1#clock set 12:37:00 ?
<1-31> Day of the month
MONTH Month of the year
R1#clock set 7:15:00 1 January 2023
R1#copy run
R1#copy running-config st
R1#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
R1#

SSH show version


R1>show version

R1> show ip interface brief


Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0/0 192.168.0.1 YES manual up up
GigabitEthernet0/0/1 192.168.1.1 YES manual up up
Loopback0 10.0.0.1 YES manual up up
Vlan1 unassigned YES unset administratively down down
R1>show ip route
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route

Gateway of last resort is not set

10.0.0.0/8 is variably subnetted, 2 subnets, 2 masks


C 10.0.0.0/24 is directly connected, Loopback0
L 10.0.0.1/32 is directly connected, Loopback0
192.168.0.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.0.0/24 is directly connected, GigabitEthernet0/0/0
L 192.168.0.1/32 is directly connected, GigabitEthernet0/0/0
192.168.1.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.1.0/24 is directly connected, GigabitEthernet0/0/1
L 192.168.1.1/32 is directly connected, GigabitEthernet0/0/1

R1>

You might also like