@bebcd 3? 3 @bebcd 3? 3 @bebcd 3? 3

© Siemens AG 2007
?)-/F)&,G$# :G,G&)$ A#-+ ; 8303 A . BI,)H#* 4227
@BEBCD 3?<3
MJH T/3'00#*:HW%# P-2-01
Q#5 L#,#0W2'-, >OJ>
K0W+# 1'7#1 >== 2- >C=
R-5#0 0W,%# =;DB )U 2- ?? )U
D81-1_N_en_U2.fm Seite 1 Montag, 17. September 2007 11:50 11
© Siemens AG 2007
Related catalogs
Additional documentation
Low-Voltage Motors D 81.1
IEC Squirrel-Cage Motors You will find all information material, such as brochures, cata-
Frame sizes 56 to 450 logs, manuals and operating instructions for standard drive sys-
tems up-to-date on the Internet at the address
Order No.: http://www.siemens.com/motors/printmaterial
E86060-K5581-A111-A2-7600 You can order the listed documentation or download it in com-
mon file formats (PDF, ZIP).
MOTOX D 87.1
Geared Motors
Catalog available soon Catalog CA 01 – Selection tool SD configurator
The selection tool SD configurator is available in combination
Order No.: with the electronic catalog CA 01.
E86060-K5287-A111-A1-7600
SINAMICS G110/SINAMICS G120 D 11.1

Inverter Chassis Units
SINAMICS G120D
Distributed Frequency Inverters
Order No.:
E86060-K5511-A111-A4-7600
SINAMICS G130 D 11
Drive Converter Chassis Units
SINAMICS G150
Drive Converter Cabinet Units
Order No.:
E86060-K5511-A101-A3-7600 On CD 2 for the selection and configuring tools, you will find the
SD configurators for low-voltage motors, MICROMASTER 4 invert-
ers, SINAMICS G110 and SINAMICS G120 inverter chassis units as
MICROMASTER DA 51.2 well as SINAMICS G120D distributed frequency inverters and
MICROMASTER 420/430/440 SIMATIC ET 200S FC frequency converters for distributed I/O,
Inverters complete with:
0.12 kW to 250 kW • Dimension drawing generator for motors
Order No.: • Data sheet generator for motors and inverters
E86060-K5151-A121-A6-7600
• Starting calculation
• 3D models in STP format
MICROMASTER/COMBIMASTER DA 51.3
MICROMASTER 411 Inverters • Extensive documentation
COMBIMASTER 411 Distributed Hardware and software requirements
Drive Solutions
• PC with 500 MHz CPU or faster
Order No.:
E86060-K5251-A131-A2-7600 • Operating systems
– Windows 98/ME
– Windows 2000
Industrial Communication IK PI – Windows XP
for Automation and Drives – Windows NT
Part 6: ET 200 Distributed I/O (Service Pack 6 or higher)
ET 200S FC Frequency Converter • 256 MB work memory (minimum)
Order No.:
• Screen resolution 1024 x 768, graphic with more than
E86060-K6710-A101-B5-7600 256 colors, small fonts
• 150 MB spare hard disk space (after installation)
AC NEMA & IEC Motors D 81.2
Further details available on the U.S./ • CD-ROM drive
Internet at: Canada • Windows-compatible sound card
• Windows-compatible mouse
http://www.sea.siemens.com/motors Installation
You can install this catalog directly from the CD-ROM as a partial
version or full version on your hard disk or in the network.
Catalog CA 01 CA 01
The Offline Mall of Automation
and Drives
Order No.:
CD: E86060-D4001-A110-C5-7600
DVD: E86060-D4001-A510-C5-7600
A&D Mall
Internet:
http://www.siemens.com/automation/mall
D81-1_N_00-01.fm Seite 1 Montag, 17. September 2007 9:46 09
© Siemens AG 2007
Page
Low-Voltage Motors 2
Introduction
• Welcome to Automation and Drives
IEC Squirrel-Cage Motors 4 • Totally Integrated Automation
New Generation 1LE1 New Generation 1LE1

Orientation
Catalog News
1/1
1/2
•
•
Overview
Benefits
1
1/2 • Application
D 81.1 N · October 2007 1/3
1/39
•
•
Technical specifications
Selection and ordering data
1/43 • More information
Supersedes: General Line motors

Catalog News D 81.1 N · April 2007 with shorter delivery time
1/44 • Selection and ordering data
© Siemens AG 2007
Self-ventilated energy-saving motors
with improved efficiency

with high efficiency
Self-ventilated motors
with increased output and
improved efficiency
Self-ventilated motors
with increased output and
high efficiency
Forced-air cooled motors
without external fan and fan cover
The products and sys- Forced-air cooled motors
tems described in this without external fan and fan cover
catalog are manufac-
tured/distributed under
application of a certified
quality management
Special versions
system in accordance
with DIN EN ISO 9001
(Certified Registration
1/78 - Voltages
No. DE-000357 QM).
1/79 - Options
The certificate is recog-
nized by all IQNet coun- Accessories and spare parts
tries. 1/86 • Overview
Dimensions
1/87 • Overview
1/90 • Dimensional drawings
Appendix
2/1 • Siemens contacts worldwide
2/2 • A&D online services
s
2/3 • Customer support
2/5
2/6
•
•
Subject index
Metal surcharges 2
2/8 • Terms and conditions of sale and delivery
2/8 • Export regulations
© Siemens AG 2007
Siemens Automation and Drives.

Welcome
More than 70,000 people aiming for the same goal:

increasing your competitiveness. That's Siemens
Automation and Drives.
We offer you a comprehensive portfolio for sustained

success in your sector, whether you're talking automa-
tion engineering, drives or electrical installation sys-
tems. Totally Integrated Automation (TIA) and Totally
Integrated Power (TIP) form the core of our offering.
TIA and TIP are the basis of our integrated range of
products and systems for the manufacturing and process
industries as well as building automation. This portfolio
is rounded off by innovative services over the entire life
cycle of your plants.
Learn for yourself the potential our products and

systems offer. And discover how you can permanently
increase your productivity with us.
Your regional Siemens contact can provide more infor-

mation. He or she will be glad to help.
2 Siemens D 81.1 N · October 2007

© Siemens AG 2007
Siemens D 81.1 N · October 2007 3

© Siemens AG 2007
Sharpen your competitive edge.

Totally Integrated Automation
With Totally Integrated Automation (TIA), Siemens is the only

manufacturer to offer an integrated range of products and sys-
tems for automation in all sectors - from incoming goods to out-
going goods, from the field level through the production control
level to connection with the corporate management level.
On the basis of TIA, we implement solutions that are perfectly
tailored to your specific requirements and are characterized by a
unique level of integration. This integration not only ensures sig-
nificant reductions in interface costs but also guarantees the
highest level of transparency across all levels.
6=< 1 @*/#-,-'.# H#.+0-O# G(M**'*%
@/&#-*#/
:@)@%#(#). 9#0#'
:6> 1 DM*0$MO/0-'*% @3#O0/'+* I4./#).
@/&#-*#/
;+#,@.&*)- 9#0#' IBD=JB> G>I <

G-+O#.. >+*/-+( 8?>I9
<)".,-+'G( 8-&#+)#-
8)"/-.,&@' >*$.1@,# $*,
6 ?#.'%* M*" @*%'*##-'*% 6 DM'*/#*M*O#
6 B*./M((M/'+* M*" >+))'..'+*'*% 6 D+"#-*'5M/'+*
6 F,#-M/'+* M*" K,%-M"#
5*).,*' 9#0#'
IBEKD@HBC IBDFJBFE
>+),0/#- E0)#-'O >+*/-+( D+/'+* >+*/-+( I4./#)
7&#'" 9#0#'
AB@9<6EC A5 5C3<)-#+$GH#
G-+O#.. B*./-0)#*/M/'+* IBD=JB> I#*.+-.
?*.@''2
8).#%,@.#"
;5BD
4/.*(@.&*)

© Siemens AG 2007
It goes without saying that you profit from Totally Integrated

Automation during the entire life cycle of your plants - from the
first planning steps, through operation, right up to moderniza-
tion. Consistent integration in the further development of our
products and systems guarantees a high degree of investment
security here.
Totally Integrated Automation makes a crucial contribution
towards optimizing everything that happens in the plant and
thus creates the conditions for a significant increase in produc-
tivity.
C<>5D<7 <D
IBD=JB> L'*>>
I>=?= I4./#)
IBD=JB> E@J IBD=JB> >+*/-+((#-. IBD=JB> ADB IM$#/4 B*/#%-M/#"

B*"0./-'M( D+"0(M-;@)N#""#";G>:NM.#" A0)M* DMO&'*# B*/#-$MO#
>+))0*'OM/'+*
IBHBKI B*"0./-'M( >+*/-+(.

I@EJHFE I2'/O&'*% ?#1'O#.
IBDF>F?@ ,-+
D+/+- DM*M%#)#*/ I4./#)
AB@9<?8D
<)".,-+'G( 8-&#+)#-
AB@9<6EC
IBE=DB>I ?-'1# I4./#). 5C3<)-#+$GH#
IBD=JB> ?'./-'N0/#" B;F
D*-G((0
<)-#%+G-#"
A*/#+
=?F4()'
:5>>5 "#$%*+&$
Siemens D 81.1 N · October 2007 5

© Siemens AG 2007
Protecting the environment

and resources.
Environmental sustainability
Environmental protection will continue to grow in importance

as a result of progressive urbanization and global population
growth. These global mega-trends make the careful and sus-
tainable handling of natural resources a central challenge.
We are convinced that every individual - and especially

every company - has an ecological responsibility. At Siemens
Automation and Drives, we stand by this conviction. Our high
environmental protection goals are part of our strict environ-
mental management. We investigate the possible effects of our
products and systems on the environment right back at the de-
velopment stage. We concern ourselves, for example, with the
question of how to reduce power consumption in plant
operation - and we offer appropriate solutions, such as our
energy-saving motors that cut power consumption in industrial
manufacturing by up to 40% thanks to their high efficiency
levels.
Many of our products and systems comply with the EC Directive

RoHS (Restriction of Hazardous Substances). All the relevant
Siemens AG sites are, of course, certified in accordance with
DIN EN ISO 14001.
Our commitment goes well beyond compliance with the rele-

vant directives and legislation: we are an active driving force
behind environmental protection, through further develop-
ment of environmental management systems, for example,
and we are involved in professional associations such as the
German Electrical and Electronic Manufacturers Association
(ZVEI).

© Siemens AG 2007
IEC Squirrel-Cage Motors

New Generation 1LE1
Orientation
■ Overview
1
G_D081_EN_00059
95
%
rated
90
85
80
75
Increasing energy costs have resulted in greater emphasis on
the power consumption of drive systems. It is extremely impor-
tant to utilize the full potential for minimization here to secure
competitiveness today and in the future. The environment will
also profit from reduced energy consumption. 70
1 2 4 6 8 10 20 40 60 kW 100
With this in mind, we have already developed a new generation
Prated
of low-voltage motors that you can use in drives to move even
more than before. Innovative copper rotors that we develop and
manufacture entirely in-house create the perfect conditions for
motors with a high degree of efficiency (EFF2 and EFF1 motors At a glance: EU/CEMEP for Europe
are located in the same housing). The new motors for EFF1 (High
• Status
Efficiency) offer considerable energy savings and protect our
Voluntary compliance with efficiency classification
environment.
• Covers
The modular mounting concept also provides total flexibility: 2-pole, 4-pole 50 Hz squirrel-cage motors from 1.1 to 90 kW
Each motor is based on a uniform concept for all markets world- (at 400 V and 50 Hz)
wide. Our motors are manufactured in accordance with modern
ecological principles and give machines and plants more drive. • Required marking
Worldwide and for every application. Efficiency over the com- Efficiency class on the motor rating plate
plete life cycle is a clear benefit of our motors especially for the ηrated, η3/4 load and efficiency class in the documentation
use of 1LE1 designed to EFF1. All machine manufacturers and Efficiency requirements according to EPACT
plant operators can profit from this – not to mention the environ- (motor version available soon)
ment. We will be launching our new 1LE1 motors onto the market
step by step. In 1997, an act was passed in the US to define minimum efficien-
cies for low-voltage three-phase motors (EPACT).
Classified energy-saving motors for an efficient energy
balance An act is in force in Canada that is largely identical, although it
is based on different verification methods. The efficiency is veri-
Depending on requirements, energy-saving motors are avail- fied for these motors for the USA using IEEE 112, Test Method B
able for an efficient energy balance for the EU in accordance and for Canada using CSA-C390. Apart from a few exceptions,
with CEMEP (European Committee of Manufacturers of Electrical all three-phase low-voltage motors imported into the USA or
Machines and Power Electronics) and will be available soon for Canada must comply with the legal efficiency requirements. The
the North American market in accordance with EPACT (US En- law demands minimum efficiency levels for motors with a voltage
ergy Policy Act). of 230 and 460 V at 60 Hz, in the output range of 1 to 200 HP
(0.75 to 150 kW) with 2, 4 and 6 poles. Explosion-proof motors
Efficiency requirements according to CEMEP
must also be included.
CEMEP classifies efficiency levels for 2-pole and 4-pole motors
The EPACT efficiency requirements exclude, for example:
with outputs of 1.1 to 90 kW. Three efficiency classes are de-
fined: • Motors whose frame size-output classification does not corre-
spond with the standard series according to NEMA MG1-12.
• EFF1 (High Efficiency motors – referred to below as “Motors
with high efficiency”) • Flange-mounting motors
• EFF2 (Improved Efficiency motors – referred to below as • Brake motors
“Motors with improved efficiency”) • Converter-fed motors
• EFF3 (Conventional Efficiency motors) • Motors with design letter C and higher
Siemens D 81.1 N · October 2007 1/1

© Siemens AG 2007

New Generation 1LE1
Orientation
■ Overview (continued)
1 EPACT lays down that the nominal efficiency at full load and a
“CC” number (Compliance Certification) must be included on
Motors with increased output and compact construction
the rating plate. The “CC” number is issued by the US Depart- Motors with increased output and compact construction can be
ment of Energy (DOE). The following information is stamped on used to advantage in confined spaces. For a slightly longer
the rating plate of EPACT motors which must be marked by law: overall length, the output is at least as high as that of the next
larger shaft height. These compact motors are also optimized for
• Nominal efficiency efficiency and therefore reduce the operating costs.
• Design letter
Motors without fan cover and external fan
• Code letter
Forced-air cooled motors with surface cooling without fan cover
• CONT and external fan are mainly used for driving fans.
• CC No. CC 032A (Siemens) and NEMA MG1-12.
Motors delivered ex-stock with shorter delivery time –
At a glance: EPACT/CSA for North America General Line
(motor version available soon)
The most popular basic versions of the 1LE1 motor series can be
• Status supplied ex-stock and are termed the “General Line”.
Minimum efficiencies required by law
• Covers A so-called “Sector version” will be available soon for some of
2-, 4- and 6-pole 60 Hz squirrel-cage motors from 1 to 200 HP the motors available from stock. These include a located bearing
(0.75 to 150 kW) for 230 V and/or 460 V 60 Hz at the drive end (DE), PTC thermistor and screwed-on feet for the
IM B35 type of construction.
• Required marking
Efficiency ηrated on the motor rating plate The normal delivery time for General Line motors is 1 to 2 days
from the time of clarification of the order at the factory until deliv-
ery from the factory. To determine the time of arrival at the cus-
tomer site, the appropriate shipping time must be added.
■ Benefits
There is considerable potential in our new 1LE1 series of low- Improved design
voltage motors. As a consistent further development of our exist-
ing motors, the 1LE1 motors offer numerous advantages: The new, optimized housing in modern EMC design has an at-
tractive appearance and enhances functionality. The rotatable,
Greater efficiency accessible connection boxes, integral eyebolts, screwed-on
feet and reinforced bearing plates ensure this.
Instead of cast-aluminum rotors, the new copper technology is
used in the EFF1 motors. The motors are therefore considerably Greater output
more compact. EFF2 and EFF1 motors are based on the same
housing. For changeover to the higher efficiency class – from For the same shaft height, our high-performance motors offer an
EFF2 to EFF1 – reconstruction of the machine is no longer nec- additional complete rated output level. The best is: We are also
essary. Savings are achieved in time and costs. And what is consistently implementing energy efficiency improvements here,
more: You can save a considerable amount of energy with EFF1 too. The motors are offered – based on the categories of
motors because they have power losses of up to 40 % less than CEMEP – in high efficiency and improved efficiency versions.
EFF2 motors. The energy saving potential and life cycle costs of More flexibility
the new motors can be calculated with our SinaSave™ software.
You can download the SinaSave program in the Internet using The optimized architecture of the motors makes installation eas-
the following link: http://www.siemens.com/energysaving. ier in general. Encoders, brakes and separately driven fans can
Our 1LE1 motors also impress customers with their extremely be retrofitted easily. Connection boxes and feet for flexible
long life and their weight-optimized design has a positive effect mounting can be selected. Smaller inventories make stockkeep-
on the stability of the equipment unit. ing easier and motor suppliers can respond to customer require-
ments more quickly. Optimized manufacturing processes sup-
port fast availability. All motors up to 460 V can be operated
either directly on line or converter-fed – without the need for any
additional measures.
■ Application
As soon as the range of motors and options is complete, it will The wide field of implementation includes the following applica-
be possible to use the 1LE1 motors from Siemens in all areas tions:
and sectors of industry due to their numerous options. They are • Pumps
suitable both for special environmental conditions such as those
that predominate in the chemical or petrochemical industries as • Fans
well as for most climatic requirements such as those of offshore • Compressors
applications. Their large range of line voltages enables them to • Conveyor systems such as cranes, belts and lifting gear
be used all over the world.
• High-bay warehouses
• Packaging machines
• Automation and Drives
1/2 Siemens D 81.1 N · October 2007

© Siemens AG 2007

New Generation 1LE1
Orientation
■ Technical specifications
Technical data at a glance 1
The following table lists the most important technical data.
Type of motor IEC Squirrel-Cage Motors 1LE1
Connection types Star connection/delta connection
You can establish the connection type used from the Order No. supplements in the selection and ordering data
for the required motor.
Number of poles 2, 4, 6, 8
Frame sizes 100 L to 160 L
Rated output 0.75 ... 22 kW
Frequencies 50 Hz and 60 Hz
Versions Self-ventilated energy-saving motors with:
• Improved efficiency (EFF2)
• High efficiency (EFF1)
Self-ventilated motors with increased output and:
Forced-air-cooled motors without external fan and fan cover with:
Marking EU/CEMEP efficiency classification, EFF1: 2-, 4-pole, EFF2: 2-, 4-pole
US Energy Policy Act EPACT: 2-, 4-, 6-pole (motor version available soon)
Rated speed (synchronous speed) 750 ... 3000 rpm
Rated torque 9.9 ... 150 Nm
Insulation of the stator winding Temperature class 155 (F), used acc. to temperature class 130 (B) (also for motors with increased output)
according to DURIGNIT IR 2000 insulation system
EN 60034-1 (IEC 60034-1)
Degree of protection IP55 as standard
according to
EN 60034-5 (IEC 60034-5)
Cooling according to Self-ventilated
EN 60034-6 (IEC 60034-6) frame sizes 100 L to 160 L (IC 411),
forced-air-cooled
frame sizes 100 L to 160 L (IC 416)
Admissible coolant temperature and –20 °C ... +40 °C as standard, site altitude up to 1000 m above sea level.
site altitude
Standard voltages according to 50 Hz: 230 V, 400 V, 500 V, 690 V
EN 60038 (IEC 60038) The voltage to be used can be found in the selection and ordering data for the required motor.
Type of construction according to Without flange:
EN 60034-7 (IEC 60034-7) IM B3, IM B6, IM B7, IM B8, IM V5 without protective cover, IM V6, IM V5 with protective cover
With flange:
IM B5, IM V1 without protective cover, IM V1 with protective cover, IM V3, IM B35
With standard flange:
IM B14, IM V19, IM V18 without protective cover, IM V18 with protective cover, IM B34
Paint finish Standard: Color RAL 7030 stone gray
Suitability of paint finish for climate group
according to IEC 60721, Part 2-1
Vibration quantity level according to Level A (normal – without special vibration requirements)
EN 60034-14 (IEC 60034-14) Optionally: Level B (with special vibration requirements)
Shaft extension according to Balance type: Half-key balancing as standard
DIN 748 (IEC 60072)
Sound pressure level according to The sound pressure level is listed in the selection and ordering data for the required motor.
DIN EN ISO 1680 (tolerance +3 dB)
Weights The weight is listed in the selection and ordering data for the required motor.
Modular mounting concept Rotary pulse encoder, brake, separately driven fan or prepared for mountings
Consistent series concept • Cast housing feet, screw-mounted feet available as an option and retrofittable
• Connection box obliquely partitioned and rotatable through 4 x 90°
• Bearings at DE and NDE are of identical design, reinforced bearings available as an option
Options See the selection and ordering data for “Special versions”

© Siemens AG 2007

New Generation 1LE1
Orientation
Cut-away diagram of a low-voltage motor
$ Motor protection Page 1/13 ( Bearings and lubrication Page 1/22

Motor connection and connection box Page 1/15
Voltages, currents and frequencies Page 1/7 ) Shaft and rotor Page 1/21
Balance and vibration quantity Page 1/21
% Windings and insulation Page 1/12
Coolant temperature and site altitude Page 1/11 * Colors and paint finish Page 1/5
& Heating and ventilation Page 1/14 + Types of construction Page 1/18
Mechanical design and degrees of protection Page 1/20
Modular technology Page 1/26 , Rating plates and extra rating plates Page 1/10
Special technology Page 1/32

© Siemens AG 2007

New Generation 1LE1
Orientation
Designs in accordance with standards and specifications The motors also comply with various national standards. The fol-
1
lowing standards have been harmonized with IEC publication
Applicable standards and specifications 60034-1 or replaced with DIN EN 60034-1 so that the motors can
The motors comply with the appropriate standards and regula- be operated at standard rated output.
tions, especially those listed in the table below. Title Country
Title IEC/EN DIN EN IS 325 India
General specifications for rotating IEC 60034-1, DIN EN 60034-1 IS 4722
electrical machines IEC 60085 NEK – IEC 60034-1 Norway
Specification of the losses and effi- IEC 60034-2 DIN EN 60034-2
ciency of rotating electrical machines
Asynchronous AC motors for general IEC 60072 DIN EN 50347 Tolerances for electrical data
use with standardized dimensions mounting
and outputs dimensions only According to DIN EN 60034, the following tolerances are permit-
Restart characteristics for rotating IEC 60034-12 DIN EN 60034-12 ted:
electrical machines Motors which comply with DIN EN 60034-1 must have a voltage
Terminal designations and direction IEC 60034-8 DIN EN 60034-8 tolerance of ±5% / frequency tolerance of ±2% (Design A). If uti-
of rotation for electrical machines lized, the admissible limit temperature of the temperature class
Designation for type of construction, IEC 60034-7 DIN EN 60034-7 may be exceeded by 10 K.
installation and connection box
position A tolerance of ±5% also applies to the rated voltage range in
Entry to connection box – DIN 42925 accordance with DIN EN 60034-1. For rated voltage and rated
Built-in thermal protection IEC 60034-11 DIN EN 60034-11 voltage range, see Page 1/7.
Noise limit values for rotating electri- IEC 60034-9 DIN EN 60034-9
cal machines Efficiency η at
Prated ≤150 kW: –0.15 ⋅ (1 –η)
IEC standard voltages IEC 60038 DIN IEC 60038
Prated >150 kW: –0.1 ⋅ (1 –η)
Cooling methods for rotating electrical IEC 60034-6 DIN EN 60034-6
machines With η being a decimal number.
Vibration severity of rotating electrical IEC 60034-14 DIN EN 60034-14
machines 1 – cos
Vibration limits – DIN ISO 10816 Power factor –
6
Degrees of protection of rotating IEC 60034-5 DIN EN 60034-5
electrical machines • Minimum absolute value: 0.02
National standards • Maximum absolute value: 0.07
The motors comply with the IEC or European standards listed Slip ±20% (for motors <1 kW ±30% is admissible)
above. The European standards replace the national standards Locked-rotor current +20%
in the following EU member states: Germany (VDE), France Locked-rotor torque –15% to +25%
(NF C), Belgium (NBNC), Great Britain (BS), Italy (CEI), Breakdown torque –10%
Netherlands (NEN), Sweden (SS), Switzerland (SEV) etc. Moment of inertia ±10%
Colors and paint finish

Type Suitability of paint finish for climate group in accordance with DIN IEC 60721, Part 2-1
Special finish Worldwide (global) Briefly: Up to 140 °C
for outdoor use in direct sunlight and/or weather condi- Contin.: Up to 120 °C
tions. Suitable for use in the tropics for <60% relative Also: for aggressive atmospheres up to 1% acid and alkali
humidity at 40 °C concentrations or permanent dampness in sheltered rooms
All motors are painted with RAL 7030 (stone gray) if the color is
not specified.
Other colors in special finish must be ordered with order codes
Y51 or Y54 and the required RAL number in plain text (for a se-
lection of the available RAL numbers/colors, see the following
page for tables for order codes Y51 and Y54).
Direct sunlight may change the color. If consistent colors are
required, we recommend paint based on polyurethane. Please
inquire.
All paint finishes can be painted over with commercially avail-
able paints. Special paints and increased layer thickness avail-
able on request.
If required, the motors can be supplied coated only in primer,
order code S01, or unpainted (unmachined cast-iron surfaces,
but primed) using order code S00.

© Siemens AG 2007

New Generation 1LE1
Orientation
Special finish in standard RAL colors – Order code Y54
1
(RAL number is required in plain text)
RAL No. Color name RAL No. Color name
1002 Sand yellow 6011 Reseda green
1013 Pearl white 6019 Pastel green
1015 Light ivory 6021 Pale green
1019 Gray beige 7000 Squirrel gray
2003 Pastel orange 7001 Silver gray
2004 Pure orange 7004 Signal gray
3000 Flame red 7011 Iron gray
3007 Black red 7016 Anthracite gray
5007 Brilliant blue 7022 Umber gray
5009 Azure blue 7031 Blue gray
5010 Gentian blue 7032 Pebble gray
5012 Light blue 7033 Cement gray
5015 Sky blue 7035 Light gray
5017 Traffic blue 9001 Cream
5018 Teal blue 9002 Gray white
5019 Capri blue 9005 Jet black
Special finish in special RAL colors – Order code Y51 (RAL number is required in plain text)
RAL No. Color name RAL No. Color name RAL No. Color name RAL No. Color name
1000 Green beige 3013 Tomato red 6002 Leaf green 7037 Dusty gray
1001 Beige 3014 Antique pink 6003 Olive green 7038 Agate gray
1003 Signal yellow 3015 Light pink 6004 Blue green 7039 Quartz gray
1004 Golden yellow 3016 Coral red 6005 Moss green 7040 Window gray
1005 Honey yellow 3017 Rose 6006 Gray olive 7042 Traffic gray A
1006 Maize yellow 3018 Strawberry red 6007 Bottle green 7043 Traffic gray B
1007 Daffodil yellow 3020 Traffic red 6008 Brown green 7044 Silk gray
1011 Brown beige 3022 Salmon pink 6009 Fir green 7045 Tele gray 1
1012 Lemon yellow 3024 Luminous red 6010 Grass green 7046 Tele gray 2
1014 Dark ivory 3026 Luminous bright red 6012 Black green 7047 Tele gray 4
1016 Sulfur yellow 3027 Raspberry red 6013 Reed green 7048 Pearl mouse gray
1017 Saffron yellow 3031 Orient red 6014 Yellow olive 8000 Green brown
1018 Zinc yellow 3032 Pearl ruby red 6015 Black olive 8001 Ocher brown
1020 Olive yellow 3033 Pearl pink 6016 Turquoise green 8002 Signal brown
1021 Rape yellow 4001 Red lilac 6017 May green 8003 Clay brown
1023 Traffic yellow 4002 Red violet 6018 Yellow green 8004 Copper brown
1024 Ochre yellow 4003 Heather violet 6020 Chrome green 8007 Fawn brown
1026 Luminous yellow 4004 Claret violet 6022 Olive drab 8008 Olive brown
1027 Curry 4005 Blue lilac 6024 Traffic green 8011 Nut brown
1028 Melon yellow 4006 Traffic purple 6025 Fern green 8012 Red brown
1032 Broom yellow 4007 Purple violet 6026 Opal green 8014 Sepia brown
1033 Dahlia yellow 4008 Signal violet 6027 Light green 8015 Chestnut
1034 Pastel yellow 4009 Pastel violet 6028 Pine green 8016 Mahogany
1035 Pearl beige 4010 Tele magenta 6029 Mint green 8017 Chocolate
1036 Pearl gold 4011 Pearl violet 6032 Signal green 8019 Gray brown
1037 Sun yellow 4012 Pearl blackberry 6033 Mint turquoise 8022 Black brown
2000 Yellow orange 5000 Violet blue 6034 Pastel turquoise 8023 Orange brown
2001 Red orange 5001 Green blue 6035 Pearl green 8024 Beige brown
2002 Vermilion 5002 Ultramarine 6036 Pearl opal green 8025 Pale brown
2005 Luminous orange 5003 Saphire blue 7002 Olive gray 8028 Terra brown
2007 Luminous bright orange 5004 Black blue 7003 Moss gray 8029 Pearl copper
2008 Bright red orange 5005 Signal blue 7005 Mouse gray 9003 Signal white
2009 Traffic orange 5008 Gray blue 7006 Beige gray 9004 Signal black
2010 Signal orange 5011 Steel blue 7008 Khaki gray 9006 White aluminum
2011 Deep orange 5013 Cobalt blue 7009 Green gray 9007 Gray aluminum
2012 Salmon orange 5014 Pigeon blue 7010 Tarpaulin gray 9010 Pure white
2013 Pearl orange 5020 Ocean blue 7012 Basalt gray 9011 Graphite black
3001 Signal red 5021 Water blue 7013 Brown gray 9016 Traffic white
3002 Carmine red 5022 Night blue 7015 Slate gray 9017 Traffic black
3003 Ruby red 5023 Distant blue 7021 Black gray 9018 Papyrus white
3004 Purple red 5024 Pastel blue 7023 Concrete gray 9022 Pearl light gray
3005 Wine red 5025 Pearl gentian 7024 Graphite gray 9023 Pearl dark gray
3009 Oxide red 5026 Pearl night blue 7026 Granite gray
3011 Brown red 6000 Patina green 7034 Yellow gray
3012 Beige red 6001 Emerald green 7036 Platinum gray

Korr_D81-1_N_01-01.fm Seite 7 Montag, 24. September 2007 9:43 09
© Siemens AG 2007

New Generation 1LE1
Orientation
Packaging, safety notes, documentation and test certifi-
1
cates
Connected in star for dispatch – Order code M01
The terminal board of the motor is connected in star for dispatch.
Connected in delta for dispatch – Order code M02
The terminal board of the motor is connected in delta for dis-
patch.
Packing weights
Packing weights
For motors For land transport
Frame size Type Type of construction IM B3 Type of construction IM B5, IM V1
In box On wooden On battens In crate In box On wooden On battens In crate
Tare board ISPM Tare Tare Tare board ISPM Tare Tare
covered by covered by
cardboard on cardboard on
top and sides top and sides
Tare Tare
kg kg kg kg kg kg kg kg
100 L 1LE1 ... -1A.4 – 5.0 – – – 5.0 – –
1LE1 ... -1A.5 – 5.0 – – – 5.0 – –
1LE1 ... -1A.6 – 5.0 – – – 5.0 – –
112 M 1LE1 ... -1B.2 – 5.0 – – – 5.0 – –
1LE1 ... -1B.6 – 5.0 – – – 5.0 – –
132 S 1LE1 ... -1C.0 4.7 – – – 5.2 – – –
1LE1 ... -1C.1 4.7 – – – 5.2 – – –
132 M 1LE1 ... -1C.2 4.7 – – – 5.2 – – –
1LE1 ... -1C.3 4.7 – – – 5.2 – – –
1LE1 ... -1C.6 8.7 – – – 9.2 – – –
160 M 1LE1 ... -1D.2 4.8 – – – 5.7 – – –
1LE1 ... -1D.3 4.8 – – – 5.7 – – –
160 L 1LE1 ... -1D.4 4.8 – – – 5.7 – – –
1LE1 ... -1D.6 8.8 – – – 9.7 – – –
Data apply for individual packaging. Packing in wire-lattice pal- Standard Category Category
lets can be used, order code B99.
60034 - 1 A B
Safety notes Voltage deviation ±5% ±10%
Frequency deviation ±2% +3%/–5%
If the motors are to be delivered without safety and commission- Rating plate data stamped with a ±5% a ±10%
ing notes, a customer’s declaration of renouncement is required. rated voltage a (e.g. 230 V) (e.g. 230 V ±5%) (e.g. 230 ±10%)
Without safety and commissioning note – Order code B00 Rating plate data stamped with b –5% to c +5% b –10% to c +10%
rated voltage ranges b to c (e.g. 220 –5% (e.g. 220 –10%
The motors are supplied with only one set of safety and commis- (e.g. 220 to 240V) to 240 +5%) to 240 +10%)
sioning notes per wire-lattice pallet for most motor types and According to the standard, longer duty is not recommended for
frame sizes. Category B. See “Rating plates and extra rating plates” for de-
Complete with one set of safety and commissioning notes tails of the rating plate inscriptions and corresponding exam-
per wire-lattice pallet – Order code B01 ples. The selection and ordering data state the rated current at
400 V. The DIN IEC 60038 standard specifies a tolerance of
Documentation ±10% for line voltages of 230 V, 400 V and 690 V. The rating
The following documents are optionally available: plates of motors with voltage code 22 or 34 specify a rated volt-
age range in addition to the rated voltage (see table below).
• Operating instructions on CD enclosed – Order code B03
The rated currents at 380/420 V are specified in the table “Rated
• Printed operating instructions English/German enclosed – currents for rated voltage range 380 V to 420 V at 50 Hz” and on
Order code B04 the rating plate.
Test certificates Line voltages Rated voltage range Voltage code
Acceptance test certificate 3.1 according to EN 10204 – 1LE1 motors
Order code B02 230 V∆/400 VY, 50 Hz 220 ... 240 V∆/380 ... 420 VY, 50 Hz 22
400 V∆/690 VY, 50 Hz 380 ... 420 V∆/660 ... 725 VY, 50 Hz 34
An acceptance test certificate 3.1 according to EN 10204 can
be supplied for most motors. 500 VY, 50 Hz – 27
500 V∆, 50 Hz – 40
Voltages, currents and frequencies
Standard voltages
EN 60034-1 differentiates between Category A (combination of
voltage deviation ±5% and frequency deviation ±2%) and Cate-
gory B (combination of voltage deviation ±10% and frequency
deviation +3/–5%) for voltage and frequency fluctuations. The
motors can supply their rated torque in both Category A and
Category B. In Category A, the temperature rise is approx. 10 K
higher than during rated duty.

© Siemens AG 2007

New Generation 1LE1
Orientation
Non-standard voltages and/or frequencies Motor Frame size Rated voltages that are available for M1Y
1 The tolerance laid down by DIN EN 60034-1 applies to all non-

standard voltages.
series Lowest/highest voltage in V for
Delta connection Star connection
Order codes have been allocated for a number of non-standard 1LE1 100 … 160 200/690 250/690
voltages at 50 or 60 Hz. They are ordered by specifying the code Order codes for other rated voltages are listed under “Order No.
digit 9 for voltage in the 12th position of the Order No. as well as supplements” in the “Selection and ordering data” as well as
the code digit 0 in the 13th position of the Order No. and the ap- “Special versions” under “Voltages”.
propriate order code.
M1Y Non-standard winding for voltages between 200 V and
690 V and rated output up to the possible rated output of the
basic version.
For voltages and rated outputs outside the range, please in-
quire.
Rated currents for rated voltage range 380 V to 420 V at 50 Hz
Motor type Frame size Currents for voltage and number of poles
380 V 420 V 380 V 420 V 380 V 420 V 380 V 420 V
2-pole 4-pole 6-pole 8-pole
I I I I I I I I
A A A A A A A A
General Line motors with shorter delivery time
Self-ventilated energy-saving motors with improved efficiency - Aluminum series 1LE1
Forced-air cooled motors without external fan and fan cover with improved efficiency - Aluminum series 1LE1
1LE1002-1A.4 100 L 6.2 5.9 5.0 4.9 3.9 4.1 2.49 2.71
1LE1002-1A.5 100 L – – 6.4 6.1 – – 3.55 3.81
1LE1002-1B.2 112 M 8.1 8.1 8.4 8.1 5.4 5.5 4.45 4.6
1LE1002-1C.0 132 S 10.9 10.3 11.5 11.4 7.3 7.7 6.2 6.5
1LE1002-1C.1 132 S 14.5 13.9 – – – – – –
1LE1002-1C.2 132 M – – 15.2 15.2 9.3 9.4 8.4 8.8
1LE1002-1C.3 132 M – – – – 13.7 12.9 – –
1LE1002-1D.2 160 M 21.7 20.7 22.4 22.8 17.0 17.7 10.5 11.6
1LE1002-1D.3 160 M 29.6 28.9 – – – – 13.8 14.6
1LE1002-1D.4 160 L 35.0 33.5 30.0 30.2 23.9 23.8 18.9 19.4
Self-ventilated energy-saving motors with high efficiency - Aluminum series 1LE1
Forced-air cooled motors without external fan and fan cover with high efficiency - Aluminum series 1LE1
1LE1001-1A.4 100 L 6.1 6.1 4.65 4.65 3.55 3.55 2.75 3.0
1LE1001-1A.5 100 L – – 6.2 6.1 – – 3.95 4.45
1LE1001-1B.2 112 M 7.8 7.6 8.3 8.2 5.1 5.0 4.5 4.55
1LE1001-1C.0 132 S 10.1 10.5 11.4 11.4 7.0 7.1 6.6 6.6
1LE1001-1C.1 132 S 14.2 13.7 – – – – – –
1LE1001-1C.2 132 M – – 14.8 14.4 8.6 8.9 8.5 8.6
1LE1001-1C.3 132 M – – – – 12 11.9 – –
1LE1001-1D.2 160 M 20.0 21.0 21.5 20.5 16.1 15.8 9.8 9.6
1LE1001-1D.3 160 M 28.0 27.0 – – – – 13.4 13.3
1LE1001-1D.4 160 L 34.0 33.0 28.5 27.5 22.5 21.5 17.5 16.8
Self-ventilated motors with increased output with improved efficiency - Aluminum series 1LE1
1LE1002-1A.6 100 L 8.1 7.9 8.5 8.5 5.4 5.3 – –
1LE1002-1B.6 112 M 10.9 10.9 11.4 11.3 7.5 8.0 – –
1LE1002-1C.6 132 M 20.3 18.9 21.8 21.3 17.0 17.6 – –
1LE1002-1D.6 160 L 40.2 37.9 36.1 35.5 33.5 34.0 – –
Self-ventilated motors with increased output and high efficiency - Aluminum series 1LE1
1LE1001-1A.6 100 L 7.8 7.6 8.3 8.4 5.0 4.95 – –
1LE1001-1B.6 112 M 10.4 9.8 11.2 11.1 6.6 6.5 – –
1LE1001-1C.6 132 M 16.5 16.5 21.5 21 16.5 16.5 – –
1LE1001-1D.6 160 L 40.0 37.5 35.5 34.5 30.5 29.0 – –

© Siemens AG 2007

New Generation 1LE1
Orientation
Outputs Part-load power factor at
The outputs or rated outputs are listed in the selection tables for
both 50 Hz and 60 Hz.
1/4
of full load
1/2 3/4 4/4 5/4
1
0.70 0.86 0.90 0.92 0.92
Efficiency, power factor, rated torque, rated speed and
direction of rotation 0.65 0.85 0.89 0.91 0.91
0.63 0.83 0.88 0.90 0.90
Efficiency and power factor 0.61 0.80 0.86 0.89 0.89
The efficiency η and power factor cos ϕ for each rated output are 0.57 0.78 0.85 0.88 0.88
listed in the selection tables in the individual sections of this cat- 0.53 0.76 0.84 0.87 0.87
alog. 0.51 0.75 0.83 0.86 0.86
For EFF1 and EFF2 motors, the 3/4-load-efficiency is also indi- 0.49 0.73 0.81 0.85 0.86
cated in the selection tables. 0.47 0.71 0.80 0.84 0.85
0.45 0.69 0.79 0.83 0.84
The part-load values stated in the two tables below are aver- 0.43 0.67 0.77 0.82 0.83
ages; precise values can be provided on request.
0.41 0.66 0.76 0.81 0.82
Part-load efficiency in % at 0.40 0.65 0.75 0.80 0.81
1/4 1/2 3/4 4/4 5/4 0.38 0.63 0.74 0.79 0.80
of full load 0.36 0.61 0.72 0.78 0.80
93 96 97 97 96.5 0.34 0.59 0.71 0.77 0.79
92 95 96 96 95.5 0.32 0.58 0.70 0.76 0.78
90 93.5 95 95 94.5 0.30 0.56 0.69 0.75 0.78
89 92.5 94 94 93.5 0.29 0.55 0.68 0.74 0.77
88 91.5 93 93 92.5 0.28 0.54 0.67 0.73 0.77
87 91 92 92 91.5 0.27 0.52 0.63 0.72 0.76
86 90 91 91 90 0.26 0.50 0.62 0.71 0.76
85 89 90 90 89
84 88 89 89 88
80 87 88 88 87 Rated speed and direction of rotation
79 86 87 87 86 The rated speeds are applicable for the rated data. The synchro-
78 85 86 86 85 nous speed changes proportionally with the line frequency. The
76 84 85 85 83.5 motors are suitable for clockwise and counter-clockwise rota-
74 83 84 84 82.5 tion.
72 82 83 83 81.5
If U1, V1, W1 are connected to L1, L2, L3, clockwise rotation
70 81 82 82 80.5 results as viewed onto the drive-end shaft extension. Counter-
68 80 81 81 79.5 clockwise rotation is achieved by swapping two phases (see
66 79 80 80 78.5 also “Heating and ventilation”, Page 1/14).
64 77 79.5 79 77.5
Rated torque
62 75.5 78.5 78 76.5
60 74 77.5 77 75 The rated torque in Nm delivered at the motor shaft is
58 73 76 76 74
56 72 75 75 73 9.55 P 1000
M=
55 71 74 74 72 n
54 70 73 73 71 P Rated output in kW
53 68 72 72 70 n Speed in rpm
52 67 71 71 69
Note:
51 66 70 70 68 If the voltage deviates from its rated value within the admissible
50 65 69 69 67 limits, the locked-rotor torque, the pull-up torque and the break-
49 64 67.5 68 66 down torque vary with the approximate square of the value, but
48 62 66.5 67 65 the locked-rotor current varies approximately linearly.
47 61 65 66 64
In the case of squirrel-cage motors, the locked-rotor torque and
46 60 64 65 63 breakdown torque are listed in the selection tables as multiples
45 59 63 64 62 of the rated torque.
44 57 62 63 61 The normal practice is to start squirrel-cage motors directly on
43 56 60.5 62 60.5 line. The torque class indicates that with direct-on-line starting,
42 55 59.5 61 59.5 even if there is an undervoltage of –5%, it is possible to start up
41 54 58.5 60 58.5 the motor against a load torque of
• 160% for CL 16
• 130% for CL 13
• 100% for CL 10
• 70% for CL 7
• 50% for CL 5
of the rated torque.

© Siemens AG 2007

New Generation 1LE1
Orientation
Rating plate and extra rating plates An extra rating plate for identification codes is also possible,
1
order code Y82.
DIN EN 60034-1 lays down that the approximate total weight for An extra rating plate or a rating plate with different rating plate
all motors is indicated on the rating plate. data can also be ordered, order code Y80.
An extra rating plate can be supplied loose for all motors, order In the standard version, the rating plate is available in interna-
code M10. tional format or in the German/English language. The language
Non-rusting steel rating plate, for scratch, heat, cold and acid re- for the rating plate can be ordered by specifying it in plain text.
sistance can be obtained, order code M11. An overview of the languages that can be ordered, at additional
cost in some cases, is provided in the table below.
Supplementary data (max. of 20 characters) can be indicated on
the rating plate and on the packaging label, order code Y84.
Overview of the languages on the rating plate
Motor Frame size Rating plate Double rating plate
type 50/60 Hz data for
International German English German French Italian Portuguese Russian 500 VY 400 V/690 V
(de) (en) (de)/ (fr)/ (it) (pt) (ru) and and
English Spanish 575 VY 460 V
(en) (es) 500 V∆ 400 V/690 V
and and
575 V∆ 460 V
1LE1 100 … 160 # " # #
# Standard version
" Without additional charge
Example of a rating plate
2 4 18 16 23 3
D-91056 Erlangen
1 3~Mot. 1LE1 002-1DB43-4AA0 E0605/0496382 02 001
16 IEC/EN 60034 160L IMB3 IP55 5
15 73 kg Th.Cl. 155(F)
17 Bearing 21
DE 6209-2ZC3 20
NE 6209-2ZC3
19
V Hz A kW cos φ eta 1/min V A
G_D081_EN_00180
400 50 29,5 15 0,82 89,4% 1460 380-420 30,0-30,2

690 Y 50 17,1 15 0,82 89,4% 1460 660-725 17,4-17,5
460 60 29,5 17,3 0,82 89,4% 1760 440-480 30,2-29,8
6 7 8 9 10 11 12 13 14 22
1 Machine type: Three-phase 13 Voltage range [V]

Low-voltage motor 14 Current range [A]
2 Order No. 15 Machine weight [kg]
3 Factory number (Ident No., 16 Standards and regulations
serial number) 17 Temperature class
4 Type of construction 18 Frame size
5 Degree of protection 19 Additional details (optional)
6 Rated voltage [V] and 20 Operating temberature range
winding connections (only if it deviates from
7 Frequency [Hz] normal)
8 Rated current [A] 21 Site altitude (only when
9 Rated output [kW] higher than 1000 m)
10 Power factor [cos ] 22 Customer data (optional)
11 Efficiency 23 Date of manufacture YYMM
12 Rated speed [rpm]

© Siemens AG 2007

New Generation 1LE1
Orientation
Coolant temperature and site altitude If the admissible motor output is no longer adequate for the
1
drive, it should be checked whether the motor with the next
The rated output specified in the selection tables is applicable higher rated output fulfills the requirements.
for continuous duty in accordance with DIN EN 60034-1 at the
frequency of 50 Hz, a coolant temperature (CT) or ambient tem- Abbreviation Description Unit
perature of 40 °C and a site altitude (SA) up to 1000 m above Padm. Admissible motor output kW
sea level. Prated Rated output kW
For higher coolant temperatures and/or site altitudes greater kHT Factor for abnormal coolant temperature and/or
site altitude
than 1000 m above sea level, the specified motor output must be
reduced using the factor kHT. The motors are designed for temperature class 155 (F) and used
in temperature class 130 (B). Under non-standard operating
Depending on the frame size of the motor or the number of conditions, if they are to be used in class 130 (B), the admissible
poles, special windings may be added to the motors for different output must be determined from the tables below.
operating conditions.
This results in an admissible output of the motor of:
Padm. = Prated ⋅ kHT
Reduction factor kHT for different site altitudes and/or coolant temperatures
Site altitude Site altitude above sea level
above sea level Coolant temperature
m <30 °C 30 °C ... 40 °C 45 °C 50 °C 55 °C 60 °C
1000 1.07 1.00 0.96 0.92 0.87 0.82
1500 1.04 0.97 0.93 0.89 0.84 0.79
2000 1.00 0.94 0.90 0.86 0.82 0.77
2500 0.96 0.90 0.86 0.83 0.78 0.74
3000 0.92 0.86 0.82 0.79 0.75 0.70
3500 0.88 0.82 0.79 0.75 0.71 0.67
4000 0.82 0.77 0.74 0.71 0.67 0.63
Coolant temperature and site altitude are rounded-off to 5 °C or 500 m.
For the following outputs, rms values are specified for coolant Ambient temperature:
temperatures (CT) of 45 °C and 50 °C that must be specified All motors can be used in the standard version at ambient tem-
when ordering. peratures between –20 to +40 °C.
Power Admissible output at 50 Hz
Motors can be used in temperature class 155 (F)
for CT 45 °C for CT 50 °C • at 40 °C with service factor 1.1, i.e. the motor can be continu-
kW kW kW ously overloaded with 10% of the rated output in the case of
11 10.5 10
EFF2 motors
15 14.5 13.8 • at 40 °C with service factor 1.15, i.e. the motor can be contin-
18.5 17.8 17 uously overloaded with 15% of the rated output in the case of
22 21 20
EFF1 motors
30 29 27.5 • above 40 °C at rated output.
When motors are used in temperature class 130 (B) for higher
For details of derating for use in class 155 (F), see “DURIGNIT ambient temperatures and/or site altitudes, derating occurs in
IR 2000 insulation system”. accordance with the table “Reduction factor kHT for different site
Motors for coolant temperatures other than 40 °C or site altitudes altitudes and/or coolant temperatures”.
higher than 1000 m above sea level for use in temperature class For motors ex stock, the service factor is indicated on the rating
130 (B) must always be ordered with the supplementary order plate.
code “-Z” and plain text. In the case of extreme derating, the op- For other temperatures, special measures are necessary.
erating data for the motors will also be less favorable due to par- When brakes are to be mounted on at temperatures below
tial utilization. freezing, please inquire.
For details of order codes for use in temperature class 155 (F),
see “DURIGNIT IR 2000 insulation system” under “Windings and
insulation”.
The following applies to all motors:
The motors can withstand 1.5 times the rated current at rated
voltage and frequency for two minutes (DIN EN 60034).

© Siemens AG 2007

New Generation 1LE1
Orientation
Windings and insulation Temperature class 155 (F), used in accordance with 155 (F),
1
other requirements
DURIGNIT IR 2000 insulation system The motors can be ordered according to temperature class 155
The DURIGNIT IR 2000 insulation system comprises high-grade (F) for use according to temperature class 155 (F) with other cus-
enameled wires and insulating sheet materials combined with tomized requirements if they are specified in plain text in the or-
solvent-free impregnating resin. der.
The system ensures a high level of mechanical and electrical Order code Y52
strength as well as good serviceability and a long motor life. Temperature class 155 (F), used in accordance with 130 (B),
The insulation system protects the winding against aggressive coolant temperature 45 °C, approx. 4% derating
gases, vapors, dust, oil and increased air humidity. It can with- For the 1LE1 motor series, a version for temperature class 155
stand the usual vibration stressing. (F) can be used according to temperature class 130 (B) at a
The insulation is suitable up to an absolute air humidity of 30 g maximum coolant temperature of 45 °C with a 4% reduction in
water per m3 of air. Moisture condensation should be prevented rated output.
from forming on the winding. Please inquire if higher values are Order code N05
required.
Temperature class 155 (F), used in accordance with 130 (B),
Please inquire about extreme applications. coolant temperature 50 °C, approx. 8% derating
Restarting against residual field and opposite phase For the 1LE1 motor series, a version for temperature class 155
(F) can be used according to temperature class 130 (B) at a
All motors can be reclosed against 100% residual field after a maximum coolant temperature of 50 °C with a 8% reduction in
line voltage failure. rated output.
Winding and insulation design with regard to temperature class Order code N06
and air humidity Temperature class 155 (F), used in accordance with 130 (B),
All motors are designed for temperature class 155 (F). coolant temperature 55 °C, approx. 13% derating
At rated output with line-fed operation, the motors can be used For the 1LE1 motor series, a version for temperature class 155
in temperature class 130 (B). (F) can be used according to temperature class 130 (B) at a
maximum coolant temperature of 55 °C with a 13% reduction in
Temperature class 155 (F), used in accordance with 155 (F), rated output.
with service factor (SF) Order code N07
For all 1LE1 motors for line-fed operation for the rated output
given in the selection table and rated voltage, a service factor of Temperature class 155 (F), used in accordance with 130 (B),
1.1 can be specified for EFF2 motors (SF = 1.15 for EFF1 motors) coolant temperature 60 °C, approx. 18% derating
also for motors with increased output. For the 1LE1 motor series, a version for temperature class 155
Order code N01 (F) can be used according to temperature class 130 (B) at a
maximum coolant temperature of 60 °C with a 18% reduction in
Temperature class 155 (F), used in accordance with 155 (F), rated output.
for increased output Order code N08
When used according to temperature class 155 (F), the rated
output as specified in the selection and ordering data can be in-
creased by 10% for EFF2 motors (15 % for EFF1 motors) also for
motors with increased output.
Order code N02
Temperature class 155 (F), used in accordance with 155 (F),
with increased coolant temperature
For line-fed motors at outputs in accordance with the catalog,
the coolant temperature can be raised to 55 °C.
Order code N03
The service factor (SF) is not indicated on the rating plate for or-
der codes N02 and N03.
For converter-fed operation at the output specified in the cata-
log, the motors are used in accordance with temperature class
155 (F). Order codes N01, N02 and N03 are not possible. This
applies to motors up to 460 V.

© Siemens AG 2007

New Generation 1LE1
Orientation
Motor protection Two sets of three temperature sensors are used if a warning is
1
required before the motor is shut down (tripped). The warning is
The order variants for motor protection are coded with letters in normally set to 10 K below the tripping temperature.
the 15th position of the Order No. and, if necessary, using order
codes. Motor protection with PTC thermistors with 6 embedded temper-
ature sensors for alarm and tripping. In the connection box,
In the standard version, the motor is designed without motor pro- 4 auxiliary terminals are required.
tection. 15th position of Order No. letter C
15th position of Order No. letter A
In order to achieve full thermal protection, it is necessary to
A distinction is made between current-dependent and motor- combine a thermally delayed overcurrent release and a PTC
temperature-dependent protection devices. thermistor. For full motor protection implemented only with PTC
Current-dependent protection devices thermistors, please inquire.
Fuses are only used to protect mains cables in the event of a Motor temperature detection with converter-fed operation
short-circuit. They are not suitable for overload protection of the KTY 84-130 temperature sensor
motor.
This sensor is a semiconductor that changes its resistance de-
The motors are usually protected by delayed overload protection pending on temperature in accordance with a defined curve.
devices (circuit breakers for motor protection or overload re-
lays).
3
G_M015_EN_00190
This protection is current-dependent and is particularly effective
in the case of a locked rotor.
R
For standard duty with short start-up times and starting currents 2.5
that are not excessive and for low numbers of switching opera-
tions, motor protection switches provide adequate protection. k
Motor protection switches are not suitable for heavy starting duty
or large numbers of switching operations. Differences in the ther- 2
mal time constants for the protection equipment and the motor
results in unnecessary early tripping when the protection switch
is set to rated current. 1.5
Motor-temperature-dependent protection devices D = 2 mA
Temperature monitors installed in the motor winding are suit-

1
able protection devices in the case of slowly rising motor tem-
perature.
When a limit temperature is reached, these bimetal switches
0.5
(NC contacts) can deactivate an auxiliary circuit. The circuit can
only be reclosed following a considerable fall in temperature.
When the motor current rises quickly (e.g. with a locked rotor),
these switches are not suitable due to their large thermal time 0
constants. 0 50 100 150 200 250 °C 300
Temperature detectors for tripping
U
15th position of Order No. letter Z and order code Q3A
The most comprehensive protection against thermal overload- KTY 84-130 temperature sensor characteristic
ing of the motor is provided by PTC thermistors (thermistor Some converters from Siemens determine the motor tempera-
motor protection) installed in the motor winding. The temperature using the resistance of the temperature sensor. They can be
ture of the winding can be accurately monitored thanks to its low set to a required temperature for alarm and tripping.
heating capacity and the excellent heat contact with the wind-
ing. When a limit temperature is reached (rated tripping temper- Motor temperature detection with embedded temperature sen-
ature), the PTC thermistors undergo a step change in resistance. sor KTY 84-130. Two auxiliary terminals are required in the con-
This is evaluated by a tripping unit and can be used to open nection box.
auxiliary circuits. The PTC thermistors themselves cannot be 15th position of Order No. letter F
subjected to high currents and voltages. This would result in The temperature sensor is embedded in the winding head of the
destruction of the semiconductor. The switching hysteresis of the motor in the same manner as a PTC thermistor. Evaluation is per-
PTC thermistor and tripping unit is low, which supports fast re- formed, for example, in the converter.
starting of the drive. Motors with this type of protection are rec- For line-fed operation, the temperature monitoring device 3RS10
ommended for heavy duty starting, switching duty, extreme that is part of the protection equipment can be ordered sepa-
changes in load, high ambient temperatures or fluctuating sup- rately. For further details, see Catalog LV 1,
ply systems. Order No.: E86060-K1002-A101-A6-7600.
Motor protection with PTC thermistors with 3 embedded temper- With NTC thermistors (mainly in the case of special machines),
ature sensors for tripping. In the connection box, 2 auxiliary ter- the tripping temperature can also be adjusted later on the trip-
minals are required. ping unit. NTC thermistors for tripping
15th position of Order No. letter B 15th position of Order No. letter Z and order code Q2A

© Siemens AG 2007

New Generation 1LE1
Orientation
Heating and ventilation Fans/Separately driven fans
1 Anti-condensation heaters
Line voltage 230 V (1~)
Motors of frame sizes 100 ... 160 have radial-flow fans in the
standard version that cool regardless of the direction of rotation
of the motor (cooling method IC 411 acc. to DIN EN 60034-6).
Order code Q02 The air flow is forced from the non-drive-end (NDE) to the drive
Line voltage 115 V (1~) end (DE).
Order code Q03 For details of separately driven fans for frame sizes 100 ... 160,
see Page 1/27.
Motors whose windings are at risk of condensation due to the
climatic conditions, e.g. inactive motors in humid atmospheres Line voltage of separately driven fan for 1LE1 motors:
or motors that are subjected to widely fluctuating temperatures, The line voltage tolerance of the separately driven fan is ±5%; for
can be equipped with anti-condensation heaters. voltage ranges, Page 1/27.
An additional M16 x 1.5 cable entry is provided for the connect- When the motor is mounted and the air intake is restricted, it
ing cable in the connection box. must be ensured that a minimum clearance is maintained be-
Anti-condensation heaters must not be switched on during oper- tween the fan cover and the wall. This clearance is calculated
ation. from the difference between the protective cover and the fan
Motor series Frame size Heater output of anti-condensation cover (differential dimension LM - L) or is specified in the de-
heaters in Watt (W) tailed dimension drawing (see also Dimensional drawings from
Line voltage at Page 1/90).
230 V 115 V
Order code Order code
For design of the fan/separately driven fan and the fan cover, see
the table below.
Q02 Q03
1LE1 100 ... 112 50 50 Motor series Frame size Fan material Fan cover
material
1LE1 132 … 160 100 100
1LE1 100 … 160 plastic plastic1)
Instead of an anti-condensation heater, another possibility (at no
extra cost) is connection of a voltage that is approximately 4 to Sheet metal fan cover
10% of the rated motor voltage to stator terminals U1 and V1;
20 to 30% of the rated motor current are sufficient to heat the For 1LE1 motor series, the fan cover can be supplied in sheet
motor. metal instead of plastic.
Order code F74
Necessary minimum cooling air flow for forced-air-cooled motors in standard duty
The required cooling air flow indicated in the selection table ap- driven which must drive the minimum cooling air flow over the
plies to continuous duty according to DIN EN 60034-1 at a cool- motor housing. The minimum air flow must pass closely over the
ant temperature (CT) and ambient temperature, respectively, of housing (comparable to self-ventilation of the motor). Otherwise,
40 °C and a site altitude (SA) of up to 1000 m above sea level. higher air flows are required to comply with admissible motor
heating levels. For a higher cooling air flow, the operating tem-
In the motor version without external fan and fan cover, order perature of the motor can be reduced.
code F90, the motor is located in the air flow of the fan to be
Frame size Required cooling air flow for number of poles
2 4 6 8
EFF1/EFF2 EFF1 EFF2 EFF1/EFF2 EFF1/EFF2
50 Hz 60 Hz 50 Hz 60 Hz 50 Hz 60 Hz 50 Hz 60 Hz 50 Hz 60 Hz
m3/min m3/min m3/min m3/min m3/min m3/min m3/min m3/min m3/min m3/min
100 3.8 4.4 2.1 2.6 2.3 2.8 1.5 1.8 1.2 1.3
112 5.0/5.4 2) 5.7/6.1 2) 2.9 3.5 2.9 3.5 1.9 2.3 1.4 1.6
132 6.3 7.3 4.6 5.7 4.6 5.7 3.1 3.8 2.4 2.9
160 10.9 13.3 6.7 8.1 7.6 9.1 5 6.1 3.8 4.5
1)
The sheet metal fan cover is used for type of constuction codes A, D, F, H,
J, K, L, N, T, U, V in combination with option H03 (condensation drainage
holes). Mounted separately driven fans and brakes are only available for
versions with sheet metal fan covers.
2)
Value: EFF1/EFF2

© Siemens AG 2007

New Generation 1LE1
Orientation
Motor connection and connection boxes Design of the connection box
Connection, circuit and connection boxes
Location of the connection box
The number of terminals and the size of the connection box are
designed for standard requirements. 1
Motor connection
The order variants for motor connection are coded with digits in
the 16th position of the Order No. Line feeder cables
The line feeder cables must be dimensioned acc. to
The connection box of the motor can be mounted in four different DIN VDE 0298. The number of required feeder cables, if neces-
locations or positions. The position of the connection box must sary in parallel, is defined by:
always be viewed from the drive end (DE).
• The max. cable cross-section which can be connected
The standard position of the connection box for General Line
motors is on top • The cable type
16th position of Order No. digit 0. • Routing
The standard position of the connection box for all other motors • Ambient temperature and the corresponding admissible cur-
is on top rent in accordance with DIN VDE 0298
16th position of Order No. digit 4. For motors with auxilliary terminals (e.g. 15th position of Order
For all motors with feet (apart from motors with increased out- No. is letter B) an M16 x 1.5 cable gland with plug is additonally
put), cast feet are standard. If rotation of the connection box in provided.
the future has to be provided for, it is recommended that the For further details, see the data sheet function in the SD gener-
option “Screwed-on feet” (instead of cast feet), order code H01, ator.
is ordered. The connection box is located on the housing and bolted in
For motors with feet and increased output, screwed-on feet are place. The connection box can be turned 4 x 90° on the terminal
standard. The connection box can be rotated later. base of the machine’s housing in the case of a terminal board
Connection box on RHS with 6 terminal studs (standard design).
16th position of Order No. digit 5. There are 2 entry holes at the standard position complete with
sealing plugs and locknuts (see figure).
Connection box on LHS
16th position of Order No. digit 6.
Connection box bottom
16th position of Order No. digit 7.
Standard
0/4
6 5
G_D081_EN_00178
Connection box in standard position

Location of the connection box with the corresponding digits in the 16th
position of the order number
The number of winding ends depends on the winding design.
Three-phase motors are connected to the three phase conduc-
tors L1, L2 and L3 of a three-phase system. The rated voltage of
the motor in the running connection must match the phase con-
ductor voltages of the network.
When the three phases are operating in a time sequence and are
connected to the terminals of the motor in alphabetical order U1,
V1 and W1, clockwise rotation is established as viewed from the
motor shaft. The direction of rotation of the motor can be re-
versed if two connecting leads are interchanged.
Labeled terminals are provided to connect the protective con-
ductor.
A PE terminal is provided in the connection box for grounding. A
grounding terminal is provided on the outside of the motor frame
– special version for 1LE1 motors.
Order code H04.
If a brake control system or thermal protection is installed, the
connections will also be in the connection box. The motors are
suitable for direct connection to the line supply.

© Siemens AG 2007

New Generation 1LE1
Orientation
Cable entry on connection box Ordering example:
1 Unless stated otherwise, the cable entry is located in the stan-

dard position as shown in the illustration.
Connection box on RHS (16th position of Order No. digit 5):
Without additional order code, cable entry from below.
The connection box can also be rotated such that the cable en- With additional order code R10:
try is located Cable entry from drive end (DE)
• Towards the drive end (DE)
(rotation of connection box by 90°, entry from DE)
Order code R10
• Towards the non-drive end (NDE)
(rotation of connection box by 90°, entry from NDE)
Order code R11
• Opposite
(rotation of connection box by 180°, entry from opposite end)
Order code R12
The dimensions of the connection box are listed in part “Dimen-
sions”, see Pages 1/87 to 1/97 in accordance with the frame size
and the “Dimension drawings”.
If the position of the connection box (connection box RHS, LHS
or above) is changed, the position of the cable entry must be
checked and, if necessary, it can be ordered with the corre-
sponding order codes (R10, R11 and R12).
Connection box in standard position, detailed view

For cable entry to a standard connection box, a metal cable
gland can be ordered for motor connection.
One cable entry, metal
Order code R15
R12
Drive end Non-drive end

R10 R11
DE NDE
Standard G_D081_EN_00177a
Locations of the cable entries with corresponding order codes

© Siemens AG 2007

New Generation 1LE1
Orientation
Connection, circuit and connection boxes
Type TB1 F00, TB1 H00, TB1 J00
1
Connections boxes for 1LE1 motors – basic data

Motors Frame size Number of cable entries Connection box material Feeder connection
1LE1 100 … 160 2 entries complete with sealing Aluminum alloy Without cable lug
plugs and locknuts
Connection box is mounted and bolted in place.
Possible positions of the connection boxes for 1LE1 motors

Motors Frame size Connection box position Rotation of connection box
Above Side, right Retrofitting 90° 180° Retrofitting
or left possible possible
1LE1 100 … 160 " " –1) " " Yes
" Available version
Connection boxes for 1LE1 motors in standard version

Frame size Connection box Number of Contact screw Max. connectable Outer cable Cable entry 2) Two-part plate
terminals thread cross-section diameter Adm. outer cable
(sealing range) diameter
2
mm mm mm
1LE1
100 TB1 F00 6 M4 4 11 … 21 2 x M32 x 1.5 –
112
132 TB1 H00 6 M4 6 11 … 21 2 x M32 x 1.5 –
160 TB1 J00 6 M5 16 19 … 28 2 x M40 x 1.5 –
– Not available
Terminal connection
The terminal board accommodates the terminals that are con-
nected to the leads to the motor windings. The terminals are
designed so that for frame sizes 100 ... 160 the external (line)
connections can be made without the need for cable lugs.
1) Retrofittable screwed-on feet (16th position of Order No. digit 5, 6, 7 and 4

with order code H01).
2) Designed for cable glands with O-ring.

© Siemens AG 2007

New Generation 1LE1
Orientation
Types of construction
1 Standard types of construction and special types of construction

Type of construction acc. to DIN EN 60034-7 Frame size Letter Order No.
14th position of supplement -Z
the Order No. with order code
Without flange
IM B3 100 L to 160 L A –
IM B6/IM 1051 100 L to 160 L T –
IM B7/IM 1061 100 L to 160 L U –
IM B8/IM 1071 100 L to 160 L V –
IM V5/IM 1011 100 L to 160 L C –

without protective cover
IM V6/IM 1031 100 L to 160 L D –
IM V5/IM 1011 100 L to 160 L C + H001)

with protective cover
With flange
IM B5/IM 3001 100 L to 160 L F –
IM V1/IM 3011 100 L to 160 L G –

IM V1/IM 3011 100 L to 160 L G + H001)

IM V3/IM 3031 100 L to 160 L H –
IM B35/IM 2001 100 L to 160 L J –
In the DIN EN 50347 standard, flanges FF with through holes

and flanges FT with tapped holes are specified.
1) A second shaft extension L05 is not possible.

© Siemens AG 2007

New Generation 1LE1
Orientation
Type of construction acc. to DIN EN 60034-7 Frame size Letter Order No.
With standard flange

14th position of
the Order No.
supplement -Z
with order code 1
IM B14/IM 3601 100 L to 160 L K –
IM V19/IM 3631 100 L to 160 L L –
IM V18/IM 3611 100 L to 160 L M –

IM V 18/IM 3611 100 L to 160 L M1) + H001)

IM B34/IM 2101 100 L to 160 L N –
In DIN EN 50347, standard flanges are assigned to the frame If mounting position IM V1 is ordered, eyebolts are supplied for
sizes as FT with tapped holes. The special flange was assigned vertical mounting.
as a large flange in the previous DIN 42677. The motors are designated in accordance with the types of con-
struction on the rating plate.
The dimensions of the following types of construction are identi-
cal: With motors that have a vertical shaft extension, the end user
IM B3, IM B6, IM B7, IM B8, IM V5 and IM V6 must prevent an ingress of fluid along the shaft.
IM B5, IM V1 and IM V3 In the case of all types of construction with shaft end down, the
IM B14, IM V18 and IM V19 version “with protective cover” is urgently recommended, see
the section “Degrees of protection”, Page 1/20.
Motors in the standard output range can be ordered in basic
types of construction IM B3, IM B5 and IM B14 and can be op- Frame design
erated in the following mounting positions – IM B6, IM B7, IM B8,
IM V5, IM V6, IM V1, IM V3 (up to frame size 160 L) or IM V18 Motors in the types of construction with feet have, in some
and IM V19. Eyebolts are available for transport and installation cases, two fixing holes at the feet at the non-drive end (NDE),
in a horizontal position. In conjunction with the eyebolts, for the see dimension tables, Pages 1/90 to 1/97. A code is cast into the
purpose of stabilizing the position when the motor is arranged motor close to the fixing retaining holes to identify the frame size.
vertically, additional lifting straps (DIN EN 1492-1) and/or clamp-
ing bands (DIN EN 12195-2) must be used.
1) A second shaft extension L05 is not possible.

© Siemens AG 2007

New Generation 1LE1
Orientation
Mechanical design and degrees of protection Brief explanation of the degree of protection
1 Eyebolts and transport

1LE1 motors without feet have four cast eyebolts as standard,
IP55: Protection against harmful dust deposits, protection
against water jets from any direction.
each offset by 90°; in the case of screwed-on feet, two eyebolts DIN EN 60529 contains a comprehensive description of this de-
are covered by the feet, so in this case only two eyebolts are gree of protection as well as test conditions.
available for use.
With motors that have a vertical shaft extension, the end user
Frame material must prevent an ingress of fluid along the shaft.
Type series Frame size Frame material Frame feet
For motors with shaft extension pointing downwards, the version
1LE1 100 … 160 Aluminum alloy Cast 1)
“with protective cover”, order code H00, is urgently recom-
mended, see also “Types of construction”, Page 1/18.
Preparation for mountings
With flange-mounting motors, for IM V3 type of construction, col-
The encoders of the “modular and special technology” can be lection of fluid in the flange basin can be prevented by drainage
fitted at a later time. The motor must be prepared for this. holes (on request).
For the brake with order code F01 and for all encoders from the The condensation drainage holes at the drive end (DE) and non-
“modular and special technology”, this preparation of the shaft drive end (NDE) are sealed (IP55) on delivery. If the condensa-
extension on NDE can be ordered with the option “Prepared for tion drainage holes are ordered for motors fo the IM B6, IM B7 or
mounting, only center hole”. IM B8 type of construction (feet located on side or top), the po-
Order code G40 sition of the drainage holes will be in the correct position for the
The length of the motor does not change because the shaft ex- type of construction.
tension is still under the fan cover. Order code H03
For the encoders When the motors are used or stored outdoors we reccommend
• 1XP8 012-10 order code G01 that they are kept under some sort of cover so that they are not
• 1XP8 012-20 order code G02 subjected to direct intensive solar radiation, rain, snow, ice or
dust over a long period of time. In such cases, technical consul-
from the “modular technology”, this preparation of the shaft tation may be appropriate.
extension on NDE can be ordered with the option “Prepared for
mounting with shaft D12”. Noise levels for line-fed operation
Order code G41 The noise levels are measured in accordance with
By using option G41, the motor length increases by dimension DIN EN ISO 1680 in a dead room. It is specified as the A-valued
∆I. For explanations of additional dimensions and weights, see measuring-surface sound pressure level LpfA in dB (A).
“Special technology”, “Dimensions and weights” from Page This is the spatial mean value of the sound pressure levels mea-
1/35. sured on the measuring surface. The measuring surface is a
For the encoders cube 1 m away from the surface of the motor. The sound power
level is also specified as LWA in dB (A).
• LL 861 900 220 order code G04 The specified values are valid at 50 Hz at rated output (see the
• HOG 9 D 1024 l order code G05 Selection and ordering data). The tolerance is +3 dB. At 60 Hz,
• HOG 10 D 1024 l order code G06 the values are approximately 4 dB (A) higher. Please inquire
about the noise levels for motors with converter-fed operation.
from the “special technology”, this preparation of the shaft
extension on NDE can be ordered with the option “Prepared for
mounting with shaft D16”.
Order code G42
By using option G42, the motor length increases by dimension
∆I. For explanations of additional dimensions and weights, see
“Special technology”, “Dimensions and weights” from Page
1/35.
Degrees of protection
All motors are designed to IP55 degree of protection. They can
be installed in dusty or humid environments. The motors are suit-
able for operation in tropical climates. Guide value <60% relative
air humidity at CT 40 °C. Other requirements are available on re-
quest.
1)
Basic version, cast feet: Special version “Screwed-on feet (instead of
cast)” with digit 5, 6 and 7 in the 16th position of the Order No. or digit 4
with order code H01. Screwed-on feet are standard for motors with
increased output.

© Siemens AG 2007

New Generation 1LE1
Orientation
Balance and vibration quantity Balancing without featherkey (N) is possible on request by
1
specifying code L01 (extra charge).
All of the rotors are dynamically balanced with an inserted half
key. This corresponds to vibration quantity level A (normal/stan- Vibration quantity level A is the standard version and is valid for
dard). The vibrational characteristics and behavior of electrical a rated frequency of 60 Hz.
machinery is specified in DIN EN 60034-14 Sept. 2004. Based
on DIN ISO 8821, the key convention “half key” must be used for Low-vibration version B can be supplied to fulfill stricter require-
balancing. ments on smooth running (additional charge).
The type of key convention used for balancing is stamped on the Vibration quantity level B
face of the DE/NDE. Not possible with parallel roller bearings.
Order code L00
F = Balancing with full key
(Full-key convention) The limits stated in the table are applicable for uncoupled, idling
H = Balancing with half key motors in free suspension.
(Half-key convention) – standard For converter-fed operation with frequencies greater than 60 Hz,
N = Balancing without key – special balancing is required for compliance with the specified
Plain text required (Convention without key) limit values (plain text: max. supply frequency/speed).
This is indicated on the rating plate of motors up to frame size For further details, see the online help in the SD configurator
112. (available soon).
Full-key balancing (F) is possible on request with order code L02
(additional charge).
Limits (rms values) for max. vibration quantity of vibration distance (s), vibration speed (v) and acceleration (a) for the shaft height H
Vibration quantity level Machine installation Shaft height H in mm
56 ≤ H ≤ 132 132 < H ≤ 280 H > 280
srms vrms arms srms vrms arms srms vrms arms
µm mm/s mm/s2 µm mm/s mm/s2 µm mm/s mm/s2
A Free suspension 25 1.6 2.5 35 2.2 3.5 45 2.8 4.4
Rigid clamping 21 1.3 2.0 29 1.8 2.8 37 2.3 3.6
B Free suspension 11 0.7 1.1 18 1.1 1.7 29 1.8 2.8
Rigid clamping – – – 14 0.9 1.4 24 1.5 2.4
For details, see standard DIN EN 60034-14, Sept. 2004.
Shaft and rotor Standard shaft made of non-rusting steel
Shaft extension For motor series 1LE1, a standard shaft made of non-rusting
steel can be ordered. This is only possible for shaft extensions
60° center hole to DIN 332, Part 2 with M3 to M24 tapped hole of standard dimensions. For non-standard shaft dimensions,
depending on the shaft diameter (see dimension tables, Pages there will be an additional charge!
1/90 to 1/97.) Order code L06
Second standard shaft extension. Please inquire about other non-rusting materials.
Order code L05.
Concentricity of shaft extension, coaxiality and linear movement
The second shaft extension can transmitt the full rated output via in accordance with DIN 42955 Tolerance R for flange-mounting
output coupling. motors
Please also inquire about the transmitted power and admissible The following are specified in DIN 42955 with Tolerance N
cantilever force if belt pulleys, chains or gear pinions are used (normal) and Tolerance R (reduced):
on the second shaft extension.
1. Concentricity tolerances for the shaft extension
A second shaft extension is not available if a rotary pulse en-
coder and/or separately driven fan is mounted. Please inquire if 2. Coaxiality tolerances for the shaft extension and flange
a brake is mounted. centering
DE (shaft extension) 3. Linear movement tolerances for the shaft extension and
Diameter Thread flange surface
mm mm
The concentricity of the shaft extension, coaxiality and linear
7 ... 10 DR M3 movement according to DIN 42955 Tolerance R for flange-
>10 ... 13 DR M4 mounting motors can be ordered using order code L08.
>13 ... 16 DR M5 This order code can be combined for motors with deep-groove
>16 ... 21 DR M6 bearings of series 60.., 62.. and 63… This cannot be supplied in
>21 ... 24 DR M8 combination with brake or encoder mounting.
>24 ... 30 DR M10 Concentricity of the shaft extension can be ordered according to
>30 ... 38 DR M12 DIN 42955 Tolerance R for types of construction without flange
>38 ... 50 DS M16 with order code L07.
>50 ... 85 DS M20
>85 ... 130 DS M24
Dimensions and tolerances for keyways and keys are designed
to DIN EN 50347. The motors are always supplied with a key in-
serted in the shaft.

© Siemens AG 2007

New Generation 1LE1
Orientation
Bearings and lubrication For increased cantilever forces (e.g. belt drives), reinforced
1
bearings can be used at the drive end (DE).
Bearing lifetime (nominal lifetime) Order code L22
The nominal bearing lifetime is defined acc. to standardized cal- Motors 1LE1 can be supplied with reinforced deep-groove bear-
culation procedures (DIN ISO 281) and is reached or even ex- ings (size range 03).
ceeded for 90% of the bearings when the motors are operated Special bearings for DE and NDE, bearing size 63, the bearing
in compliance with the data provided in the catalog. plates are manufactured from cast-iron for this purpose.
Under average operating conditions, a lifetime (Lh10) of 100 000 Order code L25
hours can be achieved. A measuring nipple for SPM shock pulse measurement is
Generally, the bearing lifetime is defined by the bearing size, the mounted to check bearing vibration. The motors have a tapped
bearing load, the operating conditions, the speed and the hole for each bearing plate and a measuring nipple with a pro-
grease lifetime. tective plug. If a second tapped hole is provided, it is fitted with
a sealing plug.
Bearing system Order code Q01
The bearing lifetime of motors with horizontal type of construc- Bearing selection for increased cantilever forces (see the table
tion is at least 40 000 hours if there is no additional axial loading “Bearing selection for 1LE1 motors – Bearing for increased can-
at the output coupling and at least 20 000 hours with the maxi- tilever forces”, Page 1/23) – “Admissible axial load” from Page
mum admissible loads. 1/25.
This assumes that the motor is operated at 50 Hz. The nominal Permanent lubrication
bearing lifetime is reduced for converter-fed operation at higher
frequencies. For permanent lubrication, the bearing grease lifetime is
matched to the bearing lifetime. This can, however, only be
For the admissible vibration values measured at the bearing plate, achieved if the motor is operated in accordance with the catalog
evaluation zones A and B specified in ISO 10816 are applicable specifications.
in order to achieve the calculated lifetime under continuous duty. In the basic version, the motors have permanent lubrication.
If higher vibration speeds will occur under the operating condi-
tions, special arrangements will be necessary (please inquire). Regreasing
In the basic bearing system, the floating bearing is situated at For motors which can be regreased at defined regreasing inter-
the drive end (DE) and the located bearing is situated at the non- vals, the bearing lifetime can be extended and/or unfavorable
drive end (NDE). factors such as temperature, mounting conditions, speed, bear-
ing size and mechanical load can be compensated.
The bearing system is axially preloaded with a spring element at
the drive end (DE) to ensure smooth running of the motor without It is possible to regrease motors, shaft heights 100 to 160. A lu-
play. (see Figure 1 of the Diagrams of bearings, Page 1/23). bricating nipple is optionally provided.
Order code L23
For frame size 160 and above, the located bearing is axially
secured at the non-drive end (NDE). Up to frame size 132, an Mechanical stress and grease lifetime
additional axially-secured located bearing can be supplied on High speeds that exceed the rated speed with converter-fed
the non-drive end (NDE) complete with a retaining ring (see Fig- operation and the resulting increased vibrations alter the me-
ure 2 of the Diagrams of bearings, Page 1/23). chanical running smoothness and the bearings are subjected to
Order code L21 increased mechanical stress. This reduces the grease lifetime
On request, the located bearing can also be supplied at the drive and the bearing lifetime (please inquire where applicable).
end (DE) (see Figure 3 of the Diagrams of bearings, Page 1/23). For converter-fed operation in particular, compliance with the
Order code L20 mechanical limit speeds nmax at maximum supply frequency
fmax is essential, see the following table “Mechanical limit
speeds nmax at maximum supply frequency fmax”.
Mechanical limit speeds nmax at maximum supply frequency fmax (standard values)
Motor 2-pole 4-pole 6-pole 8-pole
frame size nmax fmax nmax fmax nmax fmax nmax fmax
rpm Hz rpm Hz rpm Hz rpm Hz
1LE1
100 L 6000 100 4200 140 3600 180 3000 200
112 M 6000 100 4200 140 3600 180 3000 200
132 S/M 5600 90 4200 140 3600 180 3000 200
160 M/L 4800 80 4200 140 3600 180 3000 200
Grease lifetime and regreasing intervals for horizontal installation

Permanent lubrication1)
Type series Frame size Number of poles Grease lifetime up to CT 40 °C2)
1LE1 100 … 160 2 to 8 20000 h or 40000 h3)
Regreasing (basic version)1)
Type series Frame size Number of poles Regreasing interval up to CT 40 °C2)
1LE1 100 … 160 2 to 8 8000 h
1) For special uses and special greases, please inquire about grease lifetime 3) 40000 h apply to horizontally installed motors with coupling output without
and regreasing intervals. additional axial loads.
2) If the coolant temperature is increased by 10 K, the grease lifetime and
regreasing interval are halved.

© Siemens AG 2007

New Generation 1LE1
Orientation
Bearing selection table for 1LE1 motors – basic version
The bearing selection tables are only intended for planning pur-
poses. Authoritative information on the actual type of bearings
When deep-groove ball bearings with side plates are used, the
side plate is on the inside. Located bearing at drive end (DE) for 1
fitted in motors already supplied can be obtained by the factory 1LE1 motors, see special version Figure 2 in the “Diagrams of
by quoting the serial number or can be read from the rating bearings”, Page 1/23.
plate.
For motors Number of Drive end (DE) bearing Non-drive end (NDE) bearing Figure, Page 1/23
frame size poles Horizontal Vertical Horizontal Vertical
type of construction type of construction type of construction type of construction
1LE1
100 L 2 to 8 6206 2ZC3 6206 2ZC3 6206 2ZC3 6206 2ZC3 Fig. 1
112 M 2 to 8 6206 2ZC3 6206 2ZC3 6206 2ZC3 6206 2ZC3 Fig. 1
132 S/M 2 to 8 6208 2ZC31) 6208 2ZC31) 6208 2ZC31) 6208 2ZC31) Fig. 1
160 M/L 2 to 8 6209 2ZC31) 6209 2ZC31) 6209 2ZC31) 6209 2ZC31) Fig. 2
Bearing selection table for 1LE1 motors – Bearings for increased cantilever forces – Order code L22
Please inquire about noise and vibration data. The bearing se- serial number or can be read from the rating plate.
lection tables are only intended for planning purposes. Authori- When deep-groove ball bearings with side plates are used, the
tative information on the actual type of bearings fitted in motors side plate is on the inside.
already supplied can be obtained by the factory by quoting the
1LE1
100 L 2 to 8 6306 2ZC31) 6306 2ZC31) 6206 2ZC31) 6206 2ZC31) Fig. 1
112 M 2 to 8 6306 2ZC31) 6306 2ZC31) 6206 2ZC31) 6206 2ZC31) Fig. 1
Bearing selection table for 1LE1 motors – Deep-groove bearings reinforced at both ends – Order code L25
Please inquire about noise and vibration data. The bearing se- serial number or can be read from the rating plate.
lection tables are only intended for planning purposes. Authori- When deep-groove ball bearings with side plates are used, the
tative information on the actual type of bearings fitted in motors side plate is on the inside.
already supplied can be obtained by the factory by quoting the
1LE1
100 L 2 to 8 6306 2ZC31) 6306 2ZC31) 6306 2ZC31) 6306 2ZC31) Fig. 1
112 M 2 to 8 6306 2ZC31) 6306 2ZC31) 6306 2ZC31) 6306 2ZC31) Fig. 1
Diagrams of bearings
Fig. 1: Drive-end bearing Non-drive end bearing Fig. 2: Drive-end bearing Non-drive end bearing
Located bearings for 1LE1 frame size 160
G_D081_XX_00101
G_D081_XX_00103
G_D081_XX_00102
G_D081_XX_00104
Fig. 3: Drive-end bearing Non-drive end bearing

G_D081_XX_00106
G_D081_XX_00105
1)
Bearings with a side plate are used for regreasable versions (order code L23).

© Siemens AG 2007

New Generation 1LE1
Orientation
Admissible cantilever forces Admissible cantilever forces for the basic 50 Hz version
1 Admissible cantilever forces, basic version Valid are: x0 values for x = 0 and xmax. values für x = l
(l = shaft extension)
For motors Admissible cantilever force
at x0 at xmax.
G_D081_XX_00128a
FQ Frame size Order No. Number of Type Type
poles
N N
1LE1 motors, standard values for EFF1 motors1)
(Self-ventilated energy-saving motors with high efficiency/
x
Forced-air cooled motors without external fan and fan cover
xmax. x0
with high efficiency):
100 1LE1001-1AA 2 1020 815
In order to calculate the admissible cantilever forces for a radial
load, the line of force (i.e. the centerline of the pulley) of the 1LE1001-1AB 4 1250 1000
cantilever force FQ (N) must lie within the free shaft extension 1LE1001-1AC 6 1450 1155
(dimension X). 1LE1001-1AD 8 1615 1290
112 1LE1001-1BA 2 1000 790
Dimension x [mm] is the distance between the point of applica-
1LE1001-1BB 4 1250 990
tion of force FQ and the shaft shoulder. Dimension xmax. corre-
sponds to the length of the shaft extension. 1LE1001-1BC 6 1450 1150
1LE1001-1BD 8 1610 1275
Total cantilever force FQ = c ⋅ Fu 132 1LE1001-1CA 2 1505 1170
The pre-tension factor c is a value gained from experience from 1LE1001-1CB 4 1880 1460
the belt manufacturer. The following approximate value can be 1LE1001-1CC 6 2170 1680
assumed: 1LE1001-1CD 8 2420 1880
For normal flat leather belts with an idler pulley c = 2; 160 1LE1001-1DA 2 1560 1240
for V-belts c = 2 to 2.5; 1LE1001-1DB 4 2040 1590
for special synthetic belts (depending on the type of load and 1LE1001-1DC 6 2350 1820
type of belt) c = 2 to 2.5. 1LE1001-1DD 8 2610 2030
The circumferential force Fu (N) is calculated using the following Admissible cantilever forces for the basic 50 Hz version
equation Valid are: x0 values for x = 0 and xmax. values für x = l
P For motors Admissible cantilever force
Fu = 2 10 7
n D at x0 at xmax.
Fu circumferential force in N Frame size Order No. Number of Type Type
P rated motor output (transmitted power) in kW poles
n fan speed in rpm N N
D belt pulley diameter in mm 1LE1 motor values for EFF1 motors with increased output1)
(Self-ventilated motors with increased output and high
The pulleys are standardized acc. to DIN 2211, Sheet 3. efficiency):
The admissible cantilever forces at 60 Hz are approx. 80% of the 100 1LE1001-1AA 2 1010 825
50 Hz values (please inquire). 1LE1001-1AB 4 1230 1010
1LE1001-1AC 6 1440 1180
It should be observed that for types of construction IM B6,
IM B7, IM B8, IM V5 and IM V6 the belt tension is only permitted 112 1LE1001-1BA 2 970 785
to act parallel to the mounting plane or towards the mounting 1LE1001-1BB 4 1235 1000
plane and the feet must be supported. Both feet must be se- 1LE1001-1BC 6 1440 1165
cured for foot-mounting types of construction. 132 1LE1001-1CA 2 1470 1180
1LE1001-1CB 4 1830 1470
Refer to “Bearing design for increased cantilever forces”, Page
1/25. 1LE1001-1CC 6 2150 1730
160 1LE1001-1DA 2 1550 1270
1LE1001-1DB 4 1910 1550
1LE1001-1DC 6 2230 1810
1) The admissible cantilever force load of EFF2 motors can be increased by

up to 5%.

© Siemens AG 2007

New Generation 1LE1
Orientation
Bearing design for increased cantilever forces Admissible cantilever forces for the basic 50 Hz version
Deep-groove ball bearings at the drive end (DE) – Order code L22
Valid are: x0 values for x = 0 and xmax. values für x = l
1
G_D081_XX_00128a
FQ For motors Admissible cantilever force
at x0 at xmax.
Frame size Order No. Number of Type Type
poles
x N N
xmax. x0 1LE1 motor values for EEF 1 motors with increased output1)
(Self-ventilated motors with increased output and high
It should be observed that for types of construction IM B6, IM B7, efficiency):
IM B8, IM V5 and IM V6 the belt tension is only permitted to act 100 1LE1001-1AA 2 1585 1300
parallel to the mounting plane or towards the mounting plane 1LE1001-1AB 4 1960 1610
and the feet must be supported. Both feet must be secured for
1LE1001-1AC 6 2270 1865
foot-mounted types of construction.
112 1LE1001-1BA 2 1545 1250
1LE1001-1BB 4 1960 1585
Admissible cantilever forces for the basic 50 Hz version
1LE1001-1BC 6 2270 1835
Deep-groove ball bearings at the drive end (DE) – Order code L22
132 1LE1001-1CA 2 2285 1840
Valid are: x0 values for x = 0 and xmax. values für x = l
(l = shaft extension) 1LE1001-1CB 4 2860 2300
For motors Admissible cantilever force 1LE1001-1CC 6 3320 2670
at x0 at xmax. 160 1LE1001-1DA 2 2800 2240
Frame size Order No. Number of Type Type 1LE1001-1DB 4 3450 2270
poles 1LE1001-1DC 6 4000 3200
N N
1LE1 motors standard values for EFF1 motors1)
(Self-ventilated energy-saving motors with high efficiency/
Forced-air cooled motors without external fan and fan cover
with high efficiency):
100 1LE1001-1AA 2 1590 1270
1LE1001-1AB 4 1970 1575
1LE1001-1AC 6 2270 1815
1LE1001-1AD 8 2520 2015
112 1LE1001-1BA 2 1565 1240
1LE1001-1BB 4 1965 1555
1LE1001-1BC 6 2270 1800
1LE1001-1BD 8 2510 1990
132 1LE1001-1CA 2 2310 1795
1LE1001-1CB 4 2900 2250
1LE1001-1CC 6 3330 2580
1LE1001-1CD 8 3700 2870
160 1LE1001-1DA 2 2810 2170
1LE1001-1DB 4 3540 2750
1LE1001-1DC 6 4070 3160
1LE1001-1DD 8 4510 3500
Admissible axial load

1LE1 motors in vertical type of construction – basic version (exept motors with increased output)
Frame Shaft extension pointing
size 3000 rpm 1500 rpm 1000 rpm 750 rpm
downwards upwards downwards upwards downwards upwards downwards upwards
Load Load Load Load Load Load Load Load
down up down up down up down up down up down up down up down up
N N N N N N N N N N N N N N N N
100 140 700 550 280 130 990 820 285 130 1280 1110 285 130 1560 1390 285
112 140 710 550 300 130 1000 820 310 130 1290 1110 310 130 1570 1390 310
132 200 1200 950 470 180 1680 1200 470 180 1900 1600 470 190 2200 1900 440
160 1500 1400 950 1900 1900 1800 1300 2200 2200 2200 1600 2700 2700 2700 1950 2900
The values shown do not assume a cantilever force on the shaft The calculation of the admissible axial load was based on the
extension. drive with generally available coupling. For suppliers, see the
The admissible loads are valid for operation at 50 Hz; for 60 Hz, relevant section of the catalog “Accessories and spare parts”,
please inquire. Page 1/86.
Please inquire if the load direction alternates.
1) The admissible cantilever force load of EFF2 motors can be increased by

up to 5%.

© Siemens AG 2007

New Generation 1LE1
Orientation
1LE1 motors in horizontal type of construction – basic version (exept motors with increased output)
1 Frame
size
3000 rpm
Tensile Thrust load (N)
1500 rpm
1000 rpm
750 rpm
load with radial load without load with radial load without load with radial load without load with radial load without
at radial at radial at radial at radial
x0 xmax. load x0 xmax. load x0 xmax. load x0 xmax. load
N N N N N N N N N N N N N N N N
100 220 450 350 630 220 600 500 910 220 650 550 1200 220 750 650 1480
112 220 450 350 630 220 600 500 910 220 650 550 1200 220 750 650 1480
132 350 650 520 1200 350 850 700 1600 350 1020 890 1900 350 1150 1020 2200
160 1500 850 720 1500 1500 1050 920 1800 1500 1250 1120 2200 1500 1350 1220 2600
The values shown do not assume a cantilever force on the shaft The calculation of the admissible axial load was based on the
extension. drive with generally available coupling. For suppliers, see the
The admissible loads are valid for operation at 50 Hz; for 60 Hz, relevant section of the catalog “Accessories and spare parts”,
please inquire. Page 1/86.
Please inquire if the load direction alternates.
Modular technology 1XP8 012 rotary pulse encoder

Basic versions The rotary pulse encoder can be supplied already mounted in
an HTL version as 1XP8 012-10 with order code G01 or in a TTL
The range of potential applications for the 1LE1 motors can be version as 1XP8 012-20 with order code G02. The rotary pulse
broadened considerably by mounting the following modules encoder can only be mounted on a standard non-drive end
(e.g. as brake motors). (NDE), i.e. a second shaft extension cannot be supplied.
• 1XP8 012 rotary pulse encoder
The encoder can be retrofitted. The motor must be prepared for
• Separately driven fan this. When the motor is ordered, the option “Prepared for mount-
• Brake ings, center hole only”, order code G40, or the option “Prepared
for mountings with shaft D12”, order code G41, must be speci-
The brake must always be mounted in the factory for safety rea- fied (see “Mechanical design and degrees of protection”, Page
sons. The rotary pulse encoder and/or the separately driven fan 1/20).
can also be retrofitted.
The 1XP8 012 rotary pulse encoder is suitable for standard ap-
The degree of protection of the motors with modular technology plications. For further encoders, see “Special technology”, Page
is IP55. Higher degrees of protection on request. 1/32.
When a rotary pulse encoder, brake or separately driven fan is When the rotary pulse encoder is mounted, the length of the mo-
mounted, the length of the motor increases by ∆ I. For an expla- tor increases by ∆ I. For an explanation of the additional dimen-
nation of the additional dimensions and weights, see “Special sions and weights, see “Special technology”, “Dimensions and
technology”, “Dimensions and weights” from Page 1/35. weights” from Page 1/35.
The rotary pulse encoders of “Modular technology” and “Special
technology” are fitted as standard with a protective cover made
of non-corrosive sheet steel.
Technical data of rotary pulse encoders
Supply voltage UB 1XP8 012-10 (HTL version) 1XP8 012-20 (TTL version)
+10 V to +30 V 5V ±10%
Current input without load 150 mA 120 mA
Admissible load current per output max. 100 mA max. 20 mA
Pulses per revolution 1024 1024
Outputs 2 square-wave pulses A, B – 2 inverted square-wave pulses A, B
Zero pulse and inverted zero pulse
Pulse offset between the two outputs 90° 90°
Output amplitude UHigh = UB – 2.5 V UHigh > 2.5 V
ULow = 1.6 V ULow < 0.5 V
Edge interval ≥ 0.43 µs ≥ 0.43 µs
Sampling rate ≤ 300 kHz ≤ 300 kHz
Maximum speed 6000 rpm 6000 rpm
Temperature range –40 to +100 °C –40 to +100 °C
Degree of protection IP66 IP66
Maximum admissible radial cantilever force 60 N 60 N
Maximum admissible axial force 40 N 40 N
Connection system 12-pin connector (mating connector is supplied)
Certification CSA, UL CSA, UL
Weight 0.3 kg 0.3 kg

© Siemens AG 2007

New Generation 1LE1
Orientation
Separately driven fan It can also be ordered separately and retrofitted. For selection
1
information and order numbers, see the section “Accessories
The use of a separately driven fan is recommended to increase and spare parts” (available soon). A rating plate listing all the
motor utilization at low speeds and to limit noise generation at important data is fitted to the separately driven fan. Please note
speeds significantly higher than the synchronous speed. Both of the direction of rotation of the separately driven fan (axial-flow
these results can only be achieved with converter-fed operation. fan) when connecting it. Coolant temperature CTmax. 50 °C,
Please inquire about traction and vibratory operation. please inquire for higher coolant temperatures.
The separately driven fan can be supplied already fitted, When the separately driven fan is mounted, the length of the mo-
order code F70. tor increases by ∆ I. For an explanation of the additional dimen-
sions and weights, see “Special technology”, “Dimensions and
weights” from Page 1/35.
Technical data of the separately driven fan (acc. to DIN EN 60034-1 Tolerance)
Frame size Rated voltage range Frequency Rated speed Power consumption Rated current
V Hz rpm kW A
100 1 AC 230 to 277 50 2790 0.075 0.29
3 AC 220 to 290 ∆ 50 2830 0.086 0.27
3 AC 380 to 500 Y 50 2830 0.086 0.16
1 AC 230 to 277 60 3280 0.094 0.28
3 AC 220 to 332 ∆ 60 3490 0.093 0.27
3 AC 380 to 575 Y 60 3490 0.093 0.16
112 1 AC 230 to 277 50 2720 0.073 0.26
3 AC 220 to 290 ∆ 50 2770 0.085 0.27
3 AC 380 to 500 Y 50 2770 0.085 0.15
1 AC 230 to 277 60 3000 0.107 0.31
3 AC 220 to 332 ∆ 60 3280 0.094 0.28
3 AC 380 to 575 Y 60 3280 0.094 0.16
132 1 AC 230 to 277 50 2860 0.115 0.40
3 AC 220 to 290 ∆ 50 2880 0.138 0.45
3 AC 380 to 500 Y 50 2880 0.138 0.24
1 AC 230 to 277 60 3380 0.185 0.59
3 AC 220 to 332 ∆ 60 3470 0.148 0.41
3 AC 380 to 575 Y 60 3470 0.148 0.24
160 1 AC 230 to 277 50 2780 0.236 0.96
3 AC 220 to 290 ∆ 50 2840 0.220 0.76
3 AC 380 to 500 Y 50 2830 0.220 0.43
3 AC 220 to 332 ∆ 60 3400 0.284 0.94
3 AC 380 to 575 Y 60 3400 0.284 0.56

© Siemens AG 2007

New Generation 1LE1
Orientation
Brakes
1
S Gap
Spring-operated disk brakes are used for the brakes with order
code F01. When the brake is ordered, the supply voltage must
be specified. The supply voltage for brakes is explained under
“Modular technology – Additional versions”, Page 1/31.
Friction surface Solenoid
For the design of each brake type, the braking time, run-on assembly
revolutions, braking enery per braking procedure as well as the Armature disk Pressure
service life of the brake linings, see “Configuration of motors with
springs
brakes”, Page 1/30.
When a brake is mounted, the length of the motor increases by
∆ I. For an explanation of the additional dimensions and weights,
see “Special technology”, “Dimensions and weights” from Page
1/35.
The brake can be retrofitted by authorized partners. The motor
Hub Shaft
must be prepared for this. When the motor is ordered, the option
“Prepared for mountings, center hole only”, order code G40,
must be specified (see “Mechanical design and degrees of pro- Axially shiftable
tection”, Page 1/20). rotor
2LM8 spring-operated disk brake

The 2LM8 brake has IP55 degree of protection.
Pressure
Please inquire if motors with brakes are to be operated below the G_D081_EN_00076 springs
freezing point or in very humid environments (e.g. close to the
sea) with long standstill times. Please inquire if the brake motors
are used for converter-fed operation with low speeds. Design of the 2LM8 spring-operated disk brake
Design and mode of operation
The brake takes the form of a single-disk brake with two friction Rating plate
surfaces. The following brake data are specified on the motor rating plate.
The braking torque is generated by friction when pressure is ap- Brake type, supply voltage, frequency, current, temperature
plied by one or more pressure springs in the de-energized state. class, braking torque
The brake is released electromagnetically.
When the motor brakes, the rotor which can be axially shifted on
the hub or the shaft is pressed via the armature disk against the
friction surface by means of the springs. In the braked state,
there is a gap SGap between the armature disk and the solenoid
component. To release the brake, the solenoid is energized with
DC voltage. The resulting magnetic force pulls the armature disk
against the spring force on to the solenoid component. The
spring force is then no longer applied to the rotor which can ro-
tate freely.
Operating values for spring-operated brakes with standard excitation Service capabil-
ity of the brake
For motor Brake type Rated Rated braking torque Supply Current/power Brake Brake Brake Noise Lifetime Air gap
Frame braking at 100 rpm in % at the voltage input applica- release moment level Lp of brake adjust-
1)
size torque at following speeds tion time time of inertia with lining L ment
100 rpm 1500 3000 Max. t2 2) rated air required
rpm rpm speed gap after
braking
energy
LN
Nm % % % V A W ms ms kgm 2 dB (A) Nm ⋅ 10 Nm ⋅ 106
6
100 2LM8 040-5NA10 40 81 74 66 AC 230 0.2 40 43 140 0.00036 80 1350 115

2LM8 040-5NA60 AC 400 0.22
2LM8 040-5NA80 DC 24 1.67
112 2LM8 060-6NA10 60 80 73 65 AC 230 0.25 53 60 210 0.00063 77 1600 215
2LM8 060-6NA60 AC 400 0.28
2LM8 060-6NA80 DC 24 2.1
132 2LM8 100-7NA10 100 79 72 65 AC 230 0.27 55 50 270 0.0015 77 2450 325
2LM8 100-7NA60 AC 400 0.31
2LM8 100-7NA80 DC 24 2.3
160 2LM8 260-8NA10 260 75 68 65 AC 230 0.5 100 165 340 0.0073 79 7300 935
2LM8 260-8NA60 AC 400 0.47
2LM8 260-8NA80 DC 24 4.2
1) 2)
For 400 V AC and for 24 V DC, the power can deviate by up to +10% as a The specified switching times are valid for switching on the DC side with a
result of the selected supply voltage. rated release travel and with the coil already warm. They are average val-
ues which may vary depending on factors such as the rectifier type and
the release travel. The brake application time for switching on the AC side,
for example, is approximately 6 times longer than for switching on the DC
side.

© Siemens AG 2007

New Generation 1LE1
Orientation
Lifetime of the brake lining Maximum admissible speeds
The braking energy LN up to when the brake should be adjusted,
depends on various factors. The main influencing factors in-
The maximum admissible speeds from which emergency stops
can be made, are listed in the next table. These speeds should 1
clude the masses to be braked, the operating speed, the switch- be considered as recommended values and must be checked
ing frequency and therefore the temperature at the frictional sur- under actual operating conditions.
faces. It is therefore not possible to specify a value for the friction
energy until readjustment that is valid for all operating condi- The maximum admissible friction energy depends on the switch-
tions. ing frequency and is shown for the individual brakes in the fol-
lowing diagram. Increased wear can be expected when the
When used as operating brake, the specific frictional surface brakes are used for emergency stops.
wear (wear volume for the frictional work) is approximately 0.05
up to 2 cm3/kWh.
10 6
Admissible switching energy Q adm
2LM8 400
10 5
2LM8 315
2LM8 260
2LM8 100
2LM8 060
2LM8 040
2LM8 020
4
10
2LM8 010
2LM8 005
10 3
10 2
G_D081_EN_00077b
10
1 10 10 2 10 3 10 4
Switching frequency S n
Maximum admissible speeds Changing the braking torque Readjusting the air gap
For motor Brake type Max. adm. Max. adm. no-load Reduction Dimension Min. brak- Rated air Maximum air Min. rotor
Frame operating speed with emergency per notch “O1” ing torque gap gap thickness
size speed if stop function SGap Rated SGap max. hmin.
max. adm. Horizontal Vertical
operating mounting mounting
energy
utilized
rpm rpm rpm Nm mm Nm mm mm mm
100 2LM8 040-5NA . . 3000 6000 6000 1.29 12.5 21.3 0.3 0.65 8.0
112 2LM8 060-6NA . . 3000 6000 6000 1.66 11.0 32.8 0.3 0.75 7.5
132 2LM8 100-7NA . . 3000 5300 5000 1.55 13.0 61.1 0.3 0.75 8.0
160 2LM8 260-8NA . . 1500 4400 3200 5.6 17.0 157.5 0.4 1.2 12.0

© Siemens AG 2007

New Generation 1LE1
Orientation
Changing the braking torque Braking energy per braking operation Qadm
1 The brake is supplied with the braking torque already set. For
2LM8 brakes, the torque can be reduced to the dimension O1 by
The braking energy per braking operation in Nm comprises the
energy of the moments of inertia to be braked QKin and the en-
unscrewing the adjusting ring with a hook spanner. The braking ergy QL, which must be applied in order to brake against a load
torque changes by the values shown in the above table for each torque:
notch of the adjusting ring.
Qadm = QKin+QL
Readjusting the air gap
a.) The energy of the moments of inertia in Nm
Under normal operating conditions, the brake is practically
maintenance-free. The air gap SGap must only be checked at 2
J n rated
regular intervals if the application requires an extremely large Q Kin =
amount of frictional energy and readjusted to the rated gap 182.4
SGap rated at the latest when the maximum air gap SGap max. is
reached. nrated Rated speed before braking in rpm
J Total moment of inertia in kg m2
G_M015_EN_00196
b.) The braking energy in Nm against a load torque
T L n rated t Br
QL =
19.1
TL average load torque in Nm

TL is positive if it acts against the brake
TL is negative if it supports the brake
Run-on revolutions U
The number of run-on revolutions U of the motor with brake can
be calculated as follows:
n rated t Br
U= t2 +
60 2
t2 Brake application time in ms

S Gap O
h min. (S Gap rated ) O1
(S Gap max. )
Lifetime of the brake lining L and readjustment of the air gap
The brake lining wears due to friction which increases the air gap
and the release time for the brake at standard excitation.
Configuration of motors with brakes
When the brake lining is worn out, it can be replaced easily.
Braking time
In order to calculate the lifetime of the brake lining in terms of op-
The time it takes the motor to come to a standstill comprises two erations Smax, the lifetime of the brake lining L in Nm must be di-
components: vided by the braking energy Qadm:
a.) The application time of the brake t2
L
b.) The braking time tBr S max =
Q adm
J n rated
t Br =
9.55 (T B TL ) The interval between adjustments N in switching frequencies
can be calculated in terms of operations by dividing the braking
tBr Braking time in s energy LN which the brake can output until it is necessary to re-
J Total moment of inertia in kgm2 adjust the working air gap by Qadm:
nrated Rated speed of the motor with brake in rpm
TB Rated braking torque in Nm LN
TL Average load torque in Nm N=
Q adm
(if TL supports braking, TL is positive)

© Siemens AG 2007

New Generation 1LE1
Orientation
Additional versions Bridge rectifier / half-wave rectifier
2LM8 spring-operated disk brake
Motor series
Brakes are connected through a standard bridge or half-wave
rectifier or directly to the 2LM8 brake. See the circuit diagrams 1
below.
This brake is mounted on 1LE1 motors as standard.
Voltage and frequency D1
1+ 2+
2+
The solenoid coil and the brake rectifier can be connected to the
following voltages or can be supplied for the following voltages:
• Brake supply voltage: 24 V DC V1 D2 V2
Order code F10
• Brake supply voltage: 230 V AC
Order code F11 _
G_D081_XX_00085
• Brake supply voltage: 400 V AC
(directly at the terminal strip)
Order code F12
When 60 Hz is used, the voltage for the brake must not be Half-wave rectifier, 400 V AC
increased!
Order codes F10 , F11 and F12 may only be used in conjunction
with order code F01.
1+ 2+
2+
Connections D1 D2
Labeled terminals are provided in the main connection box of V2

the motor to connect the brake.
The AC voltage for the brake excitation winding is connected to D4 D3 _
the two free terminals of the rectifier block (~). G_D081_XX_00086
The brake can be released when the motor is at a standstill by

separately exciting the solenoid. In this case, an AC voltage V1
must be connected at the rectifier block terminals. The brake
remains released as long as this voltage is present.
The rectifier is protected against overvoltages by varistors in the Bridge rectifier, 230 V AC
input and output circuits.
For 24 V DC brakes, the brake terminals are directly connected
to the DC voltage source.
See the circuit diagrams below.
Fast brake application
G_D081_XX_00087
If the brake is disconnected from the line supply, the brake is ap-
plied. The application time for the brake disk is delayed as a re-
sult of the inductance of the solenoid (shutdown on the AC side).
This results in a considerable delay before the brake is mechan- L+ L-
ically applied. In order to achieve short brake application times,
the circuit must be interrupted on the DC side. To realize this, the
wire jumpers, located between contacts 1+ and 2+ at the recti-
fier are removed and replaced by the contacts of an external
switch (see circuit diagrams below). Brake connection for 24 V DC
Manual brake release with lever

The brakes can be supplied with a mechanical manual release
with lever.
Order code F50.
The dimensions of the brake lever depend on the motor frame
size and can be read from the dimension drawing generator for
motors in the SD configurator tool for low-voltage motors.

© Siemens AG 2007

New Generation 1LE1
Orientation
Special technology
1 The range of “Special technology” comprises rotary pulse en-

coders for the 1LE1 motors.
The 1LE1 motors with the order codes F70 (mounted separately
driven fan), F01 (mounted brake) and F01 + F70 (mounted brake
and separately driven fan) from the “Modular technology” range
can be combined with the LL 861 900 200, HOG9 D 1024 l and
HOG10 D 1024 I rotary pulse encoders from the “Special tech-
nology” range.
When a rotary pulse encoder is mounted, the length of the motor
increases by ∆ I. For an explanation of the additional dimensions
and weights, see “Special technology”, “Dimensions and
weights” from Page 1/35.
The rotary pulse encoders of “Modular technology” and “Special
technology” are fitted as standard with a protective cover made
of non-corrosive sheet steel.
Rotary pulse encoder LL 861 900 220
24.5
G_M015_EN_00212
69.5
100
G7
16
67
With its rugged construction, this rotary pulse encoder is also Mounting dimensions of rotary pulse encoder LL 861 900 220
suitable for difficult operating environments. It is resistant to Technical data for LL 861 900 220 (HTL version)
shock and vibration and has insulated bearings.
Supply voltage UB +9 V to +30 V
The LL 861 900 220 rotary pulse encoder can be supplied Current input without load max. 80 mA
already mounted.
Admissible load current per output 40 mA
Order code G04.
Pulses per revolution 1024
The LL 861 900 220 rotary pulse encoder can be retrofitted. The Outputs 6 short-circuit proof square-wave
motor must be prepared for this. When the motor is ordered, the pulses A, A’, B, B’, 0, 0’
option “Prepared for mountings, center hole only”, order code Pulse offset between the two outputs 90° ±25° el.
G40, or the option “Prepared for mountings with shaft D16”, or- Output amplitude UHigh >20 V
der code G42, must be specified (see “Mechanical design and ULow <2.5 V
degrees of protection”, Page 1/20). The rotary pulse encoder is Mark space ratio 1:1 ±10%
not part of the scope of supply in this case. Edge steepness 50 V/µs (without load)
The version of the rotary pulse encoder with a diagnostics sys- Maximum frequency 100 kHz for 350 m cable
tem (ADS) can be supplied by Leine and Linde. Maximum speed 4000 rpm
Temperature range –20 to +80 °C
Manufacturer:
Degree of protection IP65
Leine and Linde (Deutschland) GmbH
73430 Aalen Maximum adm. radial cantilever force 300 N
Bahnhofstraße 36 Maximum adm. axial force 100 N
Tel. +49 (0) 73 61-78093-0 Connection system Terminal strips in encoder
Fax +49 (0) 73 61-78093-11 Cable connection M20 x 1.5 radial
Weight Approx. 1.3 kg
http://www.leinelinde.com
e-mail: [email protected]

© Siemens AG 2007

New Generation 1LE1
Orientation
HOG9 D 1024 rotary pulse encoder
1
~67
16 H7
88
104.5
G_M015_EN_00213
The encoder is fitted with insulated bearings. Mounting dimensions for HOG9 D 1024 l rotary pulse encoder
The HOG9 D 1024 I rotary pulse encoder can be supplied al- Technical data for HOG9 D 1024 (TTL version)
ready mounted. Supply voltage UB +9 V to +30 V
Order code G05. Current input without load 50 mA to 100 mA
The HOG9 D 1024 l rotary pulse encoder can be retrofitted. The Admissible load current per output 60 mA, 300 mA peak
motor must be prepared for this. When the motor is ordered, the Pulses per revolution 1024
option “Prepared for mountings, center hole only”, order code Outputs 4 short-circuit proof square-wave
G40, or the option “Prepared for mountings with shaft D16”, or- pulses A, B and A’, B’
der code G42, must be specified (see “Mechanical design and Pulse offset between the two outputs 90° ±20 %
degrees of protection”, Page 1/20). The rotary pulse encoder is Output amplitude UHigh ≥ UB – 3.5 V
not part of the scope of supply in this case. ULow ≤ 1.5 V
Mark space ratio 1:1 ±20%
Manufacturer:
Baumer Hübner GmbH Edge steepness 10 V/µs
10967 Berlin Maximum frequency 120 kHz
Planufer 92b Maximum speed 7000 rpm
Tel. +49 (0) 30-6 90 03-0 Temperature range –20 to +100 °C
Fax +49 (0) 30-6 90 03-1 04 Degree of protection IP56
http://www.baumerhuebner.com Maximum adm. radial cantilever force 150 N
e-mail: [email protected] Maximum adm. axial force 100 N
Connection system Radial right-angle plug (mating con-
nector is part of the scope of supply)
Mech. design acc. to Hübner 73 522 B
Ident. No.

© Siemens AG 2007

New Generation 1LE1
Orientation
HOG10 D 1024 I rotary pulse encoder
1
G_D081_XX_00143
16 H7
105
112
This encoder is extremely rugged and is therefore suitable for Mounting dimensions for HOG10 D 1024 l rotary pulse encoder
difficult operating conditions. It is fitted with insulated bearings. Technical data for HOG10 D 1024 (HTL version)
The HOG10 D 1024 I rotary pulse encoder can be supplied al- Supply voltage UB +9 V to +30 V
ready mounted. Current input without load Approx. 100 mA
Order code G06.
Admissible load current per output 60 mA, 300 mA peak
The HOG10 D 1024 l rotary pulse encoder can be retrofitted. Pulses per revolution 1024
The motor must be prepared for this. When the motor is ordered, Outputs 4 short-circuit proof square-wave
the option “Prepared for mountings, center hole only”, order pulses A, B and A’, B’
code G40, or the option “Prepared for mountings with shaft Pulse offset between the two outputs 90° ±20%
D16”, order code G42, must be specified (see “Mechanical de- Output amplitude UHigh ≥ UB – 3.5 V
sign and degrees of protection”, Page 1/20). The rotary pulse ULow ≤ 1.5 V
encoder is not part of the scope of supply in this case. Mark space ratio 1:1 ±20%
Manufacturer: Edge steepness 10 V/µs
Baumer Hübner GmbH Maximum frequency 120 kHz
10967 Berlin Maximum speed 7000 rpm
Planufer 92b Temperature range –20 to +100 °C
Tel. +49 (0) 30-6 90 03-0 Degree of protection IP66
Fax +49 (0) 30-6 90 03-1 04 Maximum adm. radial cantilever force 150 N
http://www.baumerhuebner.com Maximum adm. axial force 80 N
e-mail: [email protected] Connection system Terminals, cable connection
M20 x 1.5
Mech. design acc. to Hübner 74 055 B
Ident. No.

© Siemens AG 2007

New Generation 1LE1
Orientation
Dimensions and weight
Fig. 1 Brake
Order code F01
[optionally with manual release, order code F50]
Fig. 2 Standard protective cover for types of construction
Order code H00 1
G_D081_XX_00191
G_D018_XX_00190
Fig. 3 Rotary pulse encoder (on cover) Fig. 4 Brake and rotary pulse encoder (on cover)
Order code G01/G02/G04/G05/G06 Order code F01
[protective cover as standard] + G01/G02/G04/G05/G06
[optionally with manual release, order code F50;
protective cover as standard]
G_D081_XX_00192
G_D081_XX_00193
Fig. 5 Separately driven fan Fig. 6 Brake and separately driven fan
Order code F70 Order code F01 + F70
M
G_D081_XX_00195
G_D081_XX_00194
Dimensions ∆l and weights, see from Page 1/37.

© Siemens AG 2007

New Generation 1LE1
Orientation
Fig. 7 Rotary pulse encoder (under the cover) and separately Fig. 8 Brake, rotary pulse encoder (under the cover) and separately
1
driven fan driven fan
Order code F70 Order code F01 + F70
+ G01/G02/G04/G05/G06 + G01/G02/G04/G05/G06
G_D081_XX_00196
G_D081_XX_00197
Fig. 9 Protective cover for separately driven fan
Order code H00
G_D081_XX_00198
Fig. 10 Prepared for mountings – only center hole Fig. 11 Prepared for mountings with shaft D12/D16
(for brake order code F01 and/or rotary pulse encoder Order codes G41/G42
order codes G01/G02/G04/G05/G06)
Order code G40
G_D081_XX_00188
G_D081_XX_00199 l
Dimensions ∆l and weights, see from Page 1/37.

© Siemens AG 2007

New Generation 1LE1
Orientation
Relevant diagram
1
Frame size Brake
2
Protective cover
3
Rotary pulse encoder including protective cover
1
1XP8 012 LL 861 900 220 HOG9 D 1024 I HOG10 D 1024 I
Order code Order code Order codes Order code Order code Order code
F01 H00 G01, G02 G04 G05 G06
∆l Weight ∆l Weight ∆l Weight ∆l Weight ∆l Weight ∆l Weight
approx. approx. approx. approx. approx. approx.
mm kg mm kg mm kg mm kg mm kg mm kg
1LE1
100 81 5.9 33 0.4 49 0.9 76 1.9 76 1.5 119 2.2
112 88 7.8 33 0.4 49 0.8 76 1.9 76 1.5 119 2.2
132 114 11.9 51.5 0.7 51.5 1.3 78.5 2.4 78.5 2 121.5 2.7
160 130 30.7 50 0.7 50 1.5 77 2.7 77 2.3 120 3
Relevant diagram
4 5
Frame size Brake and rotary pulse encoder (on cover) Separately driven fan
1XP8 012 LL 861 900 220 HOG9 D 1024 I HOG10 D 1024 I
Order codes Order codes Order codes Order codes Order code
F01 F01 F01 F01 F70
+ G01/G02 + G04 + G05 + G06
∆l Weight ∆l Weight ∆l Weight ∆l Weight ∆l M Weight
approx. approx. approx. approx. approx.
mm kg mm kg mm kg mm kg mm mm kg
1LE1
100 130 6.8 157 7.8 157 7.4 200 8.1 86.5 30 2.4
112 137 8.6 164 9.7 164 9.3 207 10 81.5 30 2.6
132 165.5 13.2 192.5 14.3 192.5 13.9 235.5 14.6 116 40 3.8
160 180 32.2 207 33.4 207 33 250 33.7 135.5 40 6.5
Relevant diagram
6 7
Frame size Brake and separately driven fan Separately driven fan and rotary pulse encoder (under cover)
Order codes Order codes Order codes Order codes Order codes
F01 + F70 F70 F70 F70 F70
+ G01/G02 + G04 + G05 + G06
∆l Weight ∆l Weight ∆l Weight ∆l Weight ∆l Weight
approx. approx. approx. approx. approx.
mm kg mm kg mm kg mm kg mm kg
1LE1
100 161.5 8.3 161.5 3.3 161.5 4.3 161.5 3.9 196.5 4.6
112 156.5 10.4 156.5 3.4 156.5 4.5 156.5 4.1 191.5 4.8
132 186 15.7 186 5.1 186 6.2 186 5.8 241 6.5
160 205.5 37.2 205.5 8 205.5 9.2 205.5 8.8 270.5 9.5
Relevant diagram
8 9
Frame size Brake, separately driven fan and rotary pulse encoder (under cover) Protective cover for separately driven fan
Order codes Order codes Order codes Order codes Order code
F01 + F70 F01 + F70 F01 + F70 F01 + F70 H00
+ G01/G02 + G04 + G05 + G06
∆l Weight ∆l Weight ∆l Weight ∆l Weight ∆l Weight Diameter
approx. approx. approx. approx. approx. of the fan cover
mm kg mm kg mm kg mm kg mm kg mm
1LE1
100 196.5 9.2 196.5 10.2 196.5 9.8 246.5 10.5 30 1.4 210
112 191.5 11.2 191.5 12.3 191.5 11.9 241.5 12.6 33 1.8 249
132 241 17 241 18.1 241 17.7 291 18.4 24 2.4 300
160 270.5 38.7 270.5 39.9 270.5 39.5 320.5 40.2 31 3 338

© Siemens AG 2007

New Generation 1LE1
Orientation
Relevant diagram
1 10
Frame size Prepared for mountings – only center hole
11
Prepared for mountings with shaft D12/D16
(for Brake order code F01 and/or rotary pulse Order codes G41/G42
encoder order codes G01/G02/G04/G05/G06)
Order code G40
Order code Order code Order code
G40 G41 G42
∆l Weight ∆l Weight ∆l Weight
approx. approx. approx.
mm kg mm kg mm kg
1LE1
100 0 0 11.3 0.15 47.3 0.2
112 0 0 7.5 0.15 47.3 0.2
132 0 0.1 10.8 0.3 50.3 0.4
160 0 0.2 5.6 0.4 45.6 0.7

© Siemens AG 2007

New Generation 1LE1
Orientation
■ Selection and ordering data

These “recommendations for drive selection” guide you step-by-step through this catalog to the required motor. 1
Step 1 Technical requirements for the motor
Determine the required Rated frequency and 3 AC 50/60 Hz,
product profile, the rated voltage 400, 500 or 690 V
following are required: Duty Standard duty (continuous duty S1 according to DIN EN 60034-1)
Degree of protection required IP..
Rated speed (No. of poles) n =................. rpm
Rated output P =................. kW
Rated torque M = P ⋅ 9550/n =................. Nm
Type of construction IM..
Step 2 Environmental requirements for the motor

Determine the installa- Ambient temperature ≤40 °C >40 °C
tion conditions Site altitude ≤1000 m >1000 m
Factors for derating None Determine the factor for derating
(for derating factor, see “Technical
information” – “Coolant temperature
and site altitude”, Page 1/11)
For preliminary selection of the motor " see subsequent pages and the corresponding “Preliminary
Step 3
selection of the motor” tables, Pages 1/41 to 1/42
Determine the range of Select the frame size and therefore the possible motors on the basis of the following parameters: cooling
possible motors method, degree of protection, rated output, rated speed and rated torque range.
Note: The standard temperature range of the motors is from 20 to +40 °C.
Step 4 Detailed selection of the motor

Determine the basic Determine the motor Order No. according to the following parameters: rated output, rated speed, rated torque
Order No. of the motor and rated current from the “Selection and ordering data” for the motors that have already been identified as
possibilities.
Step 5 Selection of the special versions (see under “Special versions”)

Completing the motor Determine special versions and the associated Order codes (e.g. special voltages and types of construction,
Order No. motor protection and degrees of protection, windings and insulation, colors and paint finish, mountings and
mounting technology, etc.).
Step 6
Select the frequency For Order No. of the converter as well as notes on selection, see Catalogs D 11, D 11.1, DA 51.2 and DA 51.3.
converter, if required

© Siemens AG 2007

New Generation 1LE1
Orientation
■ Selection and ordering data (continued)

1 Order No. code For deviations in the second and third block from the catalog
codes, either -Z or 9 should be used as appropriate.
The order number consists of a combination of figures and let-
ters and is divided into three blocks linked with hyphens for a Ordering data:
better overview, e.g. • Complete Order No. and order code(s) or plain text.
1LE1001-1DB20-1AA5-Z
H00 • If a quotation has been requested, please specify the quota-
tion number in addition to the Order No.
The first block (Positions 1 to 7) identifies the motor type; the • When ordering a complete motor as a spare part, please
second block (Positions 8 to 12) defines the motor frame size specify the works serial No. for the previously supplied motor
and length, the number of poles and in some cases the as well as the Order No.
frequency/output; and in the third block (Positions 13 to 16), the
frequency/output, type of construction and other design features
are encoded.
Structure of the Order No.: Position: 1 2 3 4 5 6 7 - 8 9 10 11 12 - 13 14 15 16
IEC squirrel-cage motors, surface-cooled
Positions 1 to 4: New generation 1 L E 1
Digit, letter, letter, digit Design or version (motor type)
• Standard:
Self-ventilated by fan mounted on and driven
by rotor
• Expansion option (F90):
Forced-air cooled by air flow from the fan to be
driven
Positions 5 to 7: • Motors with high efficiency 0 0 1
3 digits (High Efficiency, EFF1), aluminum housing
• Motors with improved efficiency 0 0 2
(Improved Efficiency, EFF2), aluminum housing
Positions 8, 9 and 11: Motor frame size 1 A 0
Digit, letter, digit (frame size as a combination of shaft height and overall length, encoded) ... ...
D 6
Position 10: Number of poles A
Letter A ... D = 2-, 4-, 6-, 8-pole ...
D
Positions 12 and 13: Voltage, circuit and frequency 0 0
2 digits ... ...
9 8
Position 14: Type of construction A
Letter (A – V) ...
V
Position 15: Motor protection A
Letter (A – Z; special versions encoded) ...
Z
Position 16: Mechanical design (motor version and connection box position)
Digit • General Line motors with shorter delivery times, limited options 0
(connection box on top, cast feet, only basic versions possible,
non-drive-end (NDE) cannot be modified)
• All options are possible or can be modified
- Connection box on top 4
- Connection box on RHS (viewed from DE) 5
- Connection box on LHS (viewed from DE) 6
- Connection box below 7
Special order versions: - Z
encoded – additional order code required
not encoded – additional plain text required
Ordering example
Selection criteria Requirement Structure of the Order No.
Motor type New generation 1LE1001-$ $$$$$-$ $$$$
Standard motor with high efficiency EFF1,
IP55 degree of protection, aluminum version
Motor frame size/No. of poles/speed 4-pole/1500 rpm 1LE1001-1DB2$
$-$
$$$$
Rated output 11 kW
Voltage and frequency 230 V∆/400 VY, 50 Hz $$$
1LE1001-1DB22-2$
Type of construction IM V5 with protective cover 1) 1LE1001-1DB22-2C$
$$-Z
H00
(Special versions) 3 PTC thermistors 1LE1001-1DB22-2CB$
$-Z
(motor protection with 3 embedded temperature H00
sensors for tripping 2)
Mechanical design Connection box on RHS 1LE1001-1DB22-2CB5-Z
(motor version) (viewed from DE) H00
Mounted separately driven fan 1LE1001-1DB22-2CB5-Z
H00 F70
1) 2)
Standard without protective cover – the protective cover is defined with No additional option must be specified in the order.
Option H00 and this option must be ordered in addition.

© Siemens AG 2007

New Generation 1LE1
Orientation

Determine the motor type according to cooling method, degree of protection and frame design 1
(for further selection according to speed or number of poles, rated output, rated torque, rated speed and rated current,
see the relevant “Preselection of the motor” tables below)
Applications for surface-cooled Cooling Standard Frame Rated output at 50 Hz
motor types method designation design
for degree of
protection to
DIN EN 60034
Part 5
Motor frame sizes (shaft heights)
56 63 71 80 90 100 112 132 160
General Line motors with Self- IP55 Aluminum 1.5 ... 18.5 kW
shorter delivery time ventilated
Energy-saving motors with Self- IP55 Aluminum 0.75 ... 18.5 kW
improved efficiency ventilated
(Improved Efficiency EFF2)
Energy-saving motors with high Self- IP55 Aluminum 0.75 ... 18.5 kW
efficiency (High Efficiency EFF1) ventilated
Motors with increased output and Self- IP55 Aluminum 2.2 ... 22 kW
improved efficiency ventilated
Motors with increased output and Self- IP55 Aluminum 2.2 ... 22 kW
high efficiency ventilated
Motors without external fan and Forced- IP55 Aluminum 0.75 ... 18.5 kW
fan cover with improved efficiency air-cooled
Motors without external fan and Forced- IP55 Aluminum 0.75 ... 18.5 kW
fan cover with high efficiency air-cooled
Preliminary selection of the motor according to motor type/series, speed or number of poles, frame size, rated output,
rated torque, rated speed and rated current
Speed Frame size Rated output Rated speed Rated torque Rated current Detailed
at 400 V selection and ordering
data
Page
rpm kW rpm Nm A
Aluminum series 1LE1 (motors with external fan)
3000, 2-pole 100 L ... 160 L 3 ... 18.5 2835 ... 2935 10 ... 60 6 ... 34 1/44 ... 1/47
1500, 4-pole 100 L ... 160 L 2.2 ... 15 1425 ... 1460 14.8 ... 98 6 ... 29.5 1/48 ... 1/51
1000, 6-pole 100 L ... 160 L 1.5 ... 11 930 ... 970 15.3 ... 109 3.8 ... 23.5 1/52 ... 1/53
Self-ventilated energy-saving motors with improved efficiency (Improved Efficiency EFF2)

data
Page
rpm kW rpm Nm A
3000, 2-pole 100 L ... 160 L 3 ... 18.5 2835 ... 2935 10 ... 60 6 ... 34 1/54 ... 1/55
1500, 4-pole 100 L ... 160 L 2.2 ... 15 1425 ... 1460 14.8 ... 98 4.85 ... 29.5 1/54 ... 1/55
1000, 6-pole 100 L ... 160 L 1.5 ... 11 930 ... 970 15.3 ... 110 3.8 ... 23.5 1/54 ... 1/55
750, 8-pole 100 L ... 160 L 0.75 ... 7.5 675 ... 720 10.4 ... 100 2.45 ... 18.6 1/54 ... 1/55
Self-ventilated energy-saving motors with high efficiency (High Efficiency EFF1)

data
Page
rpm kW rpm Nm A
3000, 2-pole 100 L ... 160 L 3 ... 18.5 2905 ... 2955 9.9 ... 60 5.9 ... 33 1/58 ... 1/59
1500, 4-pole 100 L ... 160 L 2.2 ... 15 1455 ... 1475 14 ... 97 4.55 ... 27.5 1/58 ... 1/59
1000, 6-pole 100 L ... 160 L 1.5 ... 11 965 ... 975 15 ... 108 3.5 ... 22 1/58 ... 1/59
750, 8-pole 100 L ... 160 L 0.75 ... 7.5 715 ... 735 9.9 ... 98 2.85 ... 17.4 1/58 ... 1/59

© Siemens AG 2007

New Generation 1LE1
Orientation

1 Self-ventilated motors with increased output and improved efficiency (Improved Efficiency EFF2)
Speed Frame size Rated output Rated speed Rated torque Rated current at Detailed
400 V selection and ordering
data
Page
rpm kW rpm Nm A
3000, 2-pole 100 L ... 160 L 4 ... 22 2850 ... 2930 13.3 ... 72 7.9 ... 39.5 1/62 ... 1/63
1500, 4-pole 100 L ... 160 L 4 ... 18.5 1430 ... 1460 26.8 ... 121 8.5 ... 35 1/62 ... 1/63
1000, 6-pole 100 L ... 160 L 2.2 ... 15 930 ... 965 22.5 ... 148 5.3 ... 33 1/62 ... 1/63
Self-ventilated motors with increased output and high efficiency (High Efficiency EFF1)
data
Page
rpm kW rpm Nm A
3000, 2-pole 100 L ... 160 L 4 ... 22 2905 ... 2955 13 ... 71 7.6 ... 38.5 1/66 ... 1/67
1500, 4-pole 100 L ... 160 L 4 ... 18.5 1460 ... 1475 26 ... 120 8.2 ... 34 1/66 ... 1/67
1000, 6-pole 100 L ... 160 L 2.2 ... 15 960 ... 975 22 ... 147 4.95 ... 29.5 1/66 ... 1/67
Forced-air cooled motors without external fan and fan cover with improved efficiency (Improved Efficiency EFF2)
data
Page
rpm kW rpm Nm A
Aluminum series 1LE1 (motors without external fan and fan cover)
3000, 2-pole 100 L ... 160 L 3 ... 18.5 2835 ... 2935 10 ... 60 6 ... 34 1/70 ... 1/71
1500, 4-pole 100 L ... 160 L 2.2 ... 15 1425 ... 1460 14.8 ... 98 4.85 ... 29.5 1/70 ... 1/71
1000, 6-pole 100 L ... 160 L 1.5 ... 11 930 ... 970 15.3 ... 110 3.8 ... 23.5 1/70 ... 1/71
750, 8-pole 100 L ... 160 L 0.75 ... 7.5 675 ... 720 10.4 ... 100 2.45 ... 18.6 1/70 ... 1/71
Forced-air cooled motors without external fan and fan cover with high efficiency (High Efficiency EFF1)
data
Page
rpm kW rpm Nm A
Aluminum series 1LE1 (motors without external fan and fan cover)
3000, 2-pole 100 L ... 160 L 3 ... 18.5 2905 ... 2955 9.9 ... 60 5.9 ... 33 1/74 ... 1/75
1500, 4-pole 100 L ... 160 L 2.2 ... 15 1455 ... 1475 14 ... 97 4.55 ... 27.5 1/74 ... 1/75
1000, 6-pole 100 L ... 160 L 1.5 ... 11 965 ... 975 15 ... 108 3.5 ... 22 1/74 ... 1/75
750, 8-pole 100 L ... 160 L 0.75 ... 7.5 715 ... 735 9.9 ... 98 2.85 ... 17.4 1/74 ... 1/75

© Siemens AG 2007

New Generation 1LE1
Orientation
■ More information
For further information, please get in touch with your local
Siemens contact.
1
At
http://www.siemens.com/automation/partner
you can find details of Siemens contact partners worldwide re-
sponsible for particular technologies.
You can obtain in most cases a contact partner for
• technical support
• spare parts/repairs
• service
• training
• sales or
• technical support/engineering
The selection procedure starts with:
• a country
• a product or
• a sector.
By further specifying the remaining criteria you will find exactly
the right contact partner with his/her respective expertise.

© Siemens AG 2007

New Generation 1LE1

1 Rated output at Frame
size
Operating values at rated output Order No. Price Weight
50 Hz 60 Hz Rated Rated Efficiency Efficiency Efficiency Power Rated

speed at torque at Class at at factor at current at
50 Hz 50 Hz according 50 Hz 50 Hz 50 Hz 400 V,
to CEMEP 4/4-load 3/4-load 4/4-load 50 Hz
Prated Prated FS nrated Trated ηrated ηrated cosϕrated Irated m
kW kW rpm Nm % % A kg
Motor version: temperature class 155 (F), IP55 degree of protection, used acc. to temperature class 130 (B)
2-pole – 3000 rpm at 50 Hz, 3600 rpm at 60 Hz
230 V∆/400 VY, 50 Hz; 460 VY, 60 Hz
• Without flange: IM B3, IM B6, IM B7, IM B8, IM V5 without protective cover, IM V61)
- Without motor protection
3 3.45 100 L 2835 10 EFF2 83.2 84.8 0.87 6 1LE1002-1AA42-2AA0 20
4 4.6 112 M 2930 13 EFF2 84.8 84.4 0.86 7.9 1LE1002-1BA22-2AA0 25
5.5 6.3 132 S 2905 18 EFF2 86 86.6 0.89 10.4 1LE1002-1CA02-2AA0 35
7.5 8.6 132 S 2925 24 EFF2 87.6 87.8 0.88 14 1LE1002-1CA12-2AA0 40
• With flange: IM B5, IM V1 without protective cover, IM V32)
3 3.45 100 L 2835 10 EFF2 83.2 84.8 0.87 6 1LE1002-1AA42-2FA0 21
4 4.6 112 M 2930 13 EFF2 84.8 84.4 0.86 7.9 1LE1002-1BA22-2FA0 26
5.5 6.3 132 S 2905 18 EFF2 86 86.6 0.89 10.4 1LE1002-1CA02-2FA0 40
7.5 8.6 132 S 2925 24 EFF2 87.6 87.8 0.88 14 1LE1002-1CA12-2FA0 45
- With motor protection with PTC thermistors with 3 embedded temperature sensors for tripping
3 3.45 100 L 2835 10 EFF2 83.2 84.8 0.87 6 1LE1002-1AA42-2FB0 21
• With standard flange: IM B14, IM V18 without protective cover, IM V193)
3 3.45 100 L 2835 10 EFF2 83.2 84.8 0.87 6 1LE1002-1AA42-2KA0 22
4 4.6 112 M 2930 13 EFF2 84.8 84.4 0.86 7.9 1LE1002-1BA22-2KA0 27
These motors are standard painted with special finish color RAL 7030 (stone gray).
Additional options like protective cover and condensation drainage holes are not possible.
(Connection box on top, cast feet, only basic versions possible,
non-drive end (NDE) cannot be modified)
1) Only the type of construction IM B3 will be stamped on the rating plate.

2)
Only the type of construction IM B5 will be stamped on the rating plate.
3)

© Siemens AG 2007

New Generation 1LE1

Order No. Locked-rotor torque Locked-rotor current Breakdown torque Torque
class
Moment
of inertia
Noise at rated output Flange size
according
1
with direct starting as multiple of rated Measuring- Sound to
surface sound pressure DIN EN
torque current torque 50347
pressure level level at
at 50 Hz 50 Hz
TLR/Trated ILR/Irated TB/Trated CL J LpfA LWA
kgm2 dB(A) dB(A)
230 V∆/400 VY, 50 Hz; 460 VY, 60 Hz
1LE1002-1AA42-2AA0 3.2 6.2 3.3 16 0.0034 72 84
1LE1002-1BA22-2AA0 2.7 7.3 3.7 16 0.0067 69 81
1LE1002-1CA02-2AA0 2 5.6 2.6 16 0.01267 68 80
1LE1002-1CA12-2AA0 2.2 6.4 3 16 0.01601 68 80
1LE1002-1AA42-2FA0 3.2 6.2 3.3 16 0.0034 72 84 FF 215
1LE1002-1BA22-2FA0 2.7 7.3 3.7 16 0.0067 69 81 FF 215
1LE1002-1CA02-2FA0 2 5.6 2.6 16 0.01267 68 80 FF 265
1LE1002-1CA12-2FA0 2.2 6.4 3 16 0.01601 68 80 FF 265
1LE1002-1AA42-2FB0 3.2 6.2 3.3 16 0.0034 72 84 FF 215
1LE1002-1AA42-2KA0 3.2 6.2 3.3 16 0.0034 72 84 FT 130
1LE1002-1BA22-2KA0 2.7 7.3 3.7 16 0.0067 69 81 FT 130

2)
3)

© Siemens AG 2007

New Generation 1LE1

size

50 Hz 50 Hz according 50 Hz 50 Hz 50 Hz 400 V.
400 V∆/690 VY, 50 Hz; 460 V∆, 60 Hz
3 3.45 100 L 2835 10 EFF2 83.2 84.8 0.87 6 1LE1002-1AA43-4AA0 20
4 4.6 112 M 2930 13 EFF2 84.8 84.4 0.86 7.9 1LE1002-1BA23-4AA0 25
5.5 6.3 132 S 2905 18 EFF2 86 86.6 0.89 10.4 1LE1002-1CA03-4AA0 35
7.5 8.6 132 S 2925 24 EFF2 87.6 87.8 0.88 14 1LE1002-1CA13-4AA0 40
11 12.6 160 M 2920 36 EFF2 88.4 88.7 0.85 21 1LE1002-1DA23-4AA0 60
15 17.3 160 M 2930 49 EFF2 89.5 89.6 0.84 29 1LE1002-1DA33-4AA0 68
18.5 21.3 160 L 2935 60 EFF2 90.9 91 0.86 34 1LE1002-1DA43-4AA0 78
3 3.45 100 L 2835 10 EFF2 83.2 84.8 0.87 6 1LE1002-1AA43-4AB0 20
4 4.6 112 M 2930 13 EFF2 84.8 84.4 0.86 7.9 1LE1002-1BA23-4AB0 25
5.5 6.3 132 S 2905 18 EFF2 86 86.6 0.89 10.4 1LE1002-1CA03-4AB0 35
7.5 8.6 132 S 2925 24 EFF2 87.6 87.8 0.88 14 1LE1002-1CA13-4AB0 40
11 12.6 160 M 2920 36 EFF2 88.4 88.7 0.85 21 1LE1002-1DA23-4AB0 60
15 17.3 160 M 2930 49 EFF2 89.5 89.6 0.84 29 1LE1002-1DA33-4AB0 68
18.5 21.3 160 L 2935 60 EFF2 90.9 91 0.86 34 1LE1002-1DA43-4AB0 78
3 3.45 100 L 2835 10 EFF2 83.2 84.8 0.87 6 1LE1002-1AA43-4FA0 21
4 4.6 112 M 2930 13 EFF2 84.8 84.4 0.86 7.9 1LE1002-1BA23-4FA0 26
5.5 6.3 132 S 2905 18 EFF2 86 86.6 0.89 10.4 1LE1002-1CA03-4FA0 40
7.5 8.6 132 S 2925 24 EFF2 87.6 87.8 0.88 14 1LE1002-1CA13-4FA0 45
11 12.6 160 M 2920 36 EFF2 88.4 88.7 0.85 21 1LE1002-1DA23-4FA0 69
15 17.3 160 M 2930 49 EFF2 89.5 89.6 0.84 29 1LE1002-1DA33-4FA0 77
18.5 21.3 160 L 2935 60 EFF2 90.9 91 0.86 34 1LE1002-1DA43-4FA0 87
4 4.6 112 M 2930 13 EFF2 84.8 84.4 0.86 7.9 1LE1002-1BA23-4FB0 26
5.5 6.3 132 S 2905 18 EFF2 86 86.6 0.89 10.4 1LE1002-1CA03-4FB0 40
7.5 8.6 132 S 2925 24 EFF2 87.6 87.8 0.88 14 1LE1002-1CA13-4FB0 45
11 12.6 160 M 2920 36 EFF2 88.4 88.7 0.85 21 1LE1002-1DA23-4FB0 69
15 17.3 160 M 2930 49 EFF2 89.5 89.6 0.84 29 1LE1002-1DA33-4FB0 77
18.5 21.3 160 L 2935 60 EFF2 90.9 91 0.86 34 1LE1002-1DA43-4FB0 87
1)
2)

© Siemens AG 2007

New Generation 1LE1

class
Moment
of inertia
according
1
at 50 Hz 50 Hz
kgm2 dB(A) dB(A)
400 V∆/690 VY, 50 Hz; 460 V∆, 60 Hz
1LE1002-1AA43-4AA0 3.2 6.2 3.3 16 0.0034 72 84
1LE1002-1BA23-4AA0 2.7 7.3 3.7 16 0.0067 69 81
1LE1002-1CA03-4AA0 2 5.6 2.6 16 0.01267 68 80
1LE1002-1CA13-4AA0 2.2 6.4 3 16 0.01601 68 80
1LE1002-1DA23-4AA0 2.1 6.1 2.7 16 0.02971 70 82
1LE1002-1DA33-4AA0 2.5 6.1 3.2 16 0.03619 70 82
1LE1002-1DA43-4AA0 2.5 7 3.2 16 0.04395 70 82
1LE1002-1AA43-4AB0 3.2 6.2 3.3 16 0.0034 72 84
1LE1002-1BA23-4AB0 2.7 7.3 3.7 16 0.0067 69 81
1LE1002-1CA03-4AB0 2 5.6 2.6 16 0.01267 68 80
1LE1002-1CA13-4AB0 2.2 6.4 3 16 0.01601 68 80
1LE1002-1DA23-4AB0 2.1 6.1 2.7 16 0.02971 70 82
1LE1002-1DA33-4AB0 2.5 6.1 3.2 16 0.03619 70 82
1LE1002-1DA43-4AB0 2.5 7 3.2 16 0.04395 70 82
1LE1002-1AA43-4FA0 3.2 6.2 3.3 16 0.0034 72 84 FF 215
1LE1002-1BA23-4FA0 2.7 7.3 3.7 16 0.0067 69 81 FF 215
1LE1002-1CA03-4FA0 2 5.6 2.6 16 0.01267 68 80 FF 265
1LE1002-1CA13-4FA0 2.2 6.4 3 16 0.01601 68 80 FF 265
1LE1002-1DA23-4FA0 2.1 6.1 2.7 16 0.02971 70 82 FF 300
1LE1002-1DA33-4FA0 2.5 6.1 3.2 16 0.03619 70 82 FF 300
1LE1002-1DA43-4FA0 2.5 7 3.2 16 0.04395 70 82 FF 300
1LE1002-1BA23-4FB0 2.7 7.3 3.7 16 0.0067 69 81 FF 215
1LE1002-1CA03-4FB0 2 5.6 2.6 16 0.01267 68 80 FF 265
1LE1002-1CA13-4FB0 2.2 6.4 3 16 0.01601 68 80 FF 265
1LE1002-1DA23-4FB0 2.1 6.1 2.7 16 0.02971 70 82 FF 300
1LE1002-1DA33-4FB0 2.5 6.1 3.2 16 0.03619 70 82 FF 300
1LE1002-1DA43-4FB0 2.5 7 3.2 16 0.04395 70 82 FF 300
1)
2)

© Siemens AG 2007

New Generation 1LE1

size

230 V∆/400 VY, 50 Hz; 460 VY, 60 Hz
2.2 2.55 100 L 1425 14.8 EFF2 81 84 0.81 4.85 1LE1002-1AB42-2AA0 18
3 3.45 100 L 1425 20.2 EFF2 82.8 83.6 0.85 6.2 1LE1002-1AB52-2AA0 22
4 4.6 112 M 1435 27 EFF2 84.2 85.1 0.84 8.2 1LE1002-1BB22-2AA0 27
5.5 6.3 132 S 1450 36 EFF2 86 86.5 0.83 11.2 1LE1002-1CB02-2AA0 38
7.5 8.6 132 M 1450 49 EFF2 87 87.4 0.83 15 1LE1002-1CB22-2AA0 44
11 12.6 160 M 1460 72 EFF2 88.4 88.1 0.82 22 1LE1002-1DB22-2AA0 62
15 17.3 160 L 1460 98 EFF2 89.4 89.7 0.82 29.5 1LE1002-1DB42-2AA0 73
2.2 2.55 100 L 1425 14.8 EFF2 81 84 0.81 4.85 1LE1002-1AB42-2AB0 18
2.2 2.55 100 L 1425 14.8 EFF2 81 84 0.81 4.85 1LE1002-1AB42-2FA0 19
3 3.45 100 L 1425 20.2 EFF2 82.8 83.6 0.85 6.2 1LE1002-1AB52-2FA0 23
4 4.6 112 M 1435 27 EFF2 84.2 85.1 0.84 8.2 1LE1002-1BB22-2FA0 28
5.5 6.3 132 S 1450 36 EFF2 86 86.5 0.83 11.2 1LE1002-1CB02-2FA0 43
7.5 8.6 132 M 1450 49 EFF2 87 87.4 0.83 15 1LE1002-1CB22-2FA0 49
11 12.6 160 M 1460 72 EFF2 88.4 88.1 0.82 22 1LE1002-1DB22-2FA0 71
15 17.3 160 L 1460 98 EFF2 89.4 89.7 0.82 29.5 1LE1002-1DB42-2FA0 82
2.2 2.55 100 L 1425 14.8 EFF2 81 84 0.81 4.85 1LE1002-1AB42-2FB0 19
3 3.45 100 L 1425 20.2 EFF2 82.8 83.6 0.85 6.2 1LE1002-1AB52-2FB0 23
4 4.6 112 M 1435 27 EFF2 84.2 85.1 0.84 8.2 1LE1002-1BB22-2FB0 28
2.2 2.55 100 L 1425 14.8 EFF2 81 84 0.81 4.85 1LE1002-1AB42-2KA0 20
3 3.45 100 L 1425 20.2 EFF2 82.8 83.6 0.85 6.2 1LE1002-1AB52-2KA0 24
4 4.6 112 M 1435 27 EFF2 84.2 85.1 0.84 8.2 1LE1002-1BB22-2KA0 29

2)
3)

© Siemens AG 2007

New Generation 1LE1

class
Moment
of inertia
according
1
at 50 Hz 50 Hz
kgm2 dB(A) dB(A)
230 V∆/400 VY, 50 Hz; 460 VY, 60 Hz
1LE1002-1AB42-2AA0 2.3 5.1 2.7 16 0.0059 63 75
1LE1002-1AB52-2AA0 2.4 5.4 2.6 16 0.0078 63 75
1LE1002-1BB22-2AA0 2.2 5.3 2.6 16 0.0102 58 70
1LE1002-1CB02-2AA0 2.3 6.2 2.7 16 0.0186 64 76
1LE1002-1CB22-2AA0 2.5 6.6 2.9 16 0.02371 64 76
1LE1002-1DB22-2AA0 2.3 6.4 3.1 16 0.04395 64 76
1LE1002-1DB42-2AA0 2.5 7 3.4 16 0.05616 64 76
1LE1002-1AB42-2AB0 2.3 5.1 2.7 16 0.0059 63 75
1LE1002-1AB42-2FA0 2.3 5.1 2.7 16 0.0059 63 75 FF 215
1LE1002-1AB52-2FA0 2.4 5.4 2.6 16 0.0078 63 75 FF 215
1LE1002-1BB22-2FA0 2.2 5.3 2.6 16 0.0102 58 70 FF 215
1LE1002-1CB02-2FA0 2.3 6.2 2.7 16 0.0186 64 76 FF 265
1LE1002-1CB22-2FA0 2.5 6.6 2.9 16 0.02371 64 76 FF 265
1LE1002-1DB22-2FA0 2.3 6.4 3.1 16 0.04395 64 76 FF 300
1LE1002-1DB42-2FA0 2.5 7 3.4 16 0.05616 64 76 FF 300
1LE1002-1AB42-2FB0 2.3 5.1 2.7 16 0.0059 63 75 FF 215
1LE1002-1AB52-2FB0 2.4 5.4 2.6 16 0.0078 63 75 FF 215
1LE1002-1BB22-2FB0 2.2 5.3 2.6 16 0.0102 58 70 FF 215
1LE1002-1AB42-2KA0 2.3 5.1 2.7 16 0.0059 63 75 FT 130
1LE1002-1AB52-2KA0 2.4 5.4 2.6 16 0.0078 63 75 FT 130
1LE1002-1BB22-2KA0 2.2 5.3 2.6 16 0.0102 58 70 FT 130

2)
3)

© Siemens AG 2007

New Generation 1LE1

size

400 V∆/690 VY, 50 Hz; 460 V∆, 60 Hz
2.2 2.55 100 L 1425 14.8 EFF2 81 84 0.81 4.85 1LE1002-1AB43-4AA0 18
3 3.45 100 L 1425 20.2 EFF2 82.8 83.6 0.85 6.2 1LE1002-1AB53-4AA0 22
4 4.6 112 M 1435 27 EFF2 84.2 85.1 0.84 8.2 1LE1002-1BB23-4AA0 27
5.5 6.3 132 S 1450 36 EFF2 86 86.5 0.83 11.2 1LE1002-1CB03-4AA0 38
7.5 8.6 132 M 1450 49 EFF2 87 87.4 0.83 15 1LE1002-1CB23-4AA0 44
11 12.6 160 M 1460 72 EFF2 88.4 88.1 0.82 22 1LE1002-1DB23-4AA0 62
15 17.3 160 L 1460 98 EFF2 89.4 89.7 0.82 29.5 1LE1002-1DB43-4AA0 73
2.2 2.55 100 L 1425 14.8 EFF2 81 84 0.81 4.85 1LE1002-1AB43-4AB0 18
3 3.45 100 L 1425 20.2 EFF2 82.8 83.6 0.85 6.2 1LE1002-1AB53-4AB0 22
4 4.6 112 M 1435 27 EFF2 84.2 85.1 0.84 8.2 1LE1002-1BB23-4AB0 27
5.5 6.3 132 S 1450 36 EFF2 86 86.5 0.83 11.2 1LE1002-1CB03-4AB0 38
7.5 8.6 132 M 1450 49 EFF2 87 87.4 0.83 15 1LE1002-1CB23-4AB0 44
11 12.6 160 M 1460 72 EFF2 88.4 88.1 0.82 22 1LE1002-1DB23-4AB0 62
15 17.3 160 L 1460 98 EFF2 89.4 89.7 0.82 29.5 1LE1002-1DB43-4AB0 73
2.2 2.55 100 L 1425 14.8 EFF2 81 84 0.81 4.85 1LE1002-1AB43-4FA0 19
3 3.45 100 L 1425 20.2 EFF2 82.8 83.6 0.85 6.2 1LE1002-1AB53-4FA0 23
4 4.6 112 M 1435 27 EFF2 84.2 85.1 0.84 8.2 1LE1002-1BB23-4FA0 28
5.5 6.3 132 S 1450 36 EFF2 86 86.5 0.83 11.2 1LE1002-1CB03-4FA0 43
7.5 8.6 132 M 1450 49 EFF2 87 87.4 0.83 15 1LE1002-1CB23-4FA0 49
11 12.6 160 M 1460 72 EFF2 88.4 88.1 0.82 22 1LE1002-1DB23-4FA0 71
15 17.3 160 L 1460 98 EFF2 89.4 89.7 0.82 29.5 1LE1002-1DB43-4FA0 82
4 4.6 112 M 1435 27 EFF2 84.2 85.1 0.84 8.2 1LE1002-1BB23-4FB0 28
5.5 6.3 132 S 1450 36 EFF2 86 86.5 0.83 11.2 1LE1002-1CB03-4FB0 43
7.5 8.6 132 M 1450 49 EFF2 87 87.4 0.83 15 1LE1002-1CB23-4FB0 49
11 12.6 160 M 1460 72 EFF2 88.4 88.1 0.82 22 1LE1002-1DB23-4FB0 71
15 17.3 160 L 1460 98 EFF2 89.4 89.7 0.82 29.5 1LE1002-1DB43-4FB0 82
• With flange: IM B35
5.5 6.3 132 S 1450 36 EFF2 86 86.5 0.83 11.2 1LE1002-1CB03-4JA0 43
7.5 8.6 132 M 1450 49 EFF2 87 87.4 0.83 15 1LE1002-1CB23-4JA0 49
11 12.6 160 M 1460 72 EFF2 88.4 88.1 0.82 22 1LE1002-1DB23-4JA0 71
15 17.3 160 L 1460 98 EFF2 89.4 89.7 0.82 29.5 1LE1002-1DB43-4JA0 82
1)
2)

© Siemens AG 2007

New Generation 1LE1

class
Moment
of inertia
according
1
at 50 Hz 50 Hz
kgm2 dB(A) dB(A)
400 V∆/690 VY, 50 Hz; 460 V∆, 60 Hz
1LE1002-1AB43-4AA0 2.3 5.1 2.7 16 0.0059 63 75
1LE1002-1AB53-4AA0 2.4 5.4 2.6 16 0.0078 63 75
1LE1002-1BB23-4AA0 2.2 5.3 2.6 16 0.0102 58 70
1LE1002-1CB03-4AA0 2.3 6.2 2.7 16 0.0186 64 76
1LE1002-1CB23-4AA0 2.5 6.6 2.9 16 0.02371 64 76
1LE1002-1DB23-4AA0 2.3 6.4 3.1 16 0.04395 64 76
1LE1002-1DB43-4AA0 2.5 7 3.4 16 0.05616 64 76
1LE1002-1AB43-4AB0 2.3 5.1 2.7 16 0.0059 63 75
1LE1002-1AB53-4AB0 2.4 5.4 2.6 16 0.0078 63 75
1LE1002-1BB23-4AB0 2.2 5.3 2.6 16 0.0102 58 70
1LE1002-1CB03-4AB0 2.3 6.2 2.7 16 0.0186 64 76
1LE1002-1CB23-4AB0 2.5 6.6 2.9 16 0.02371 64 76
1LE1002-1DB23-4AB0 2.3 6.4 3.1 16 0.04395 64 76
1LE1002-1DB43-4AB0 2.5 7 3.4 16 0.05616 64 76
1LE1002-1AB43-4FA0 2.3 5.1 2.7 16 0.0059 63 75 FF 215
1LE1002-1AB53-4FA0 2.4 5.4 2.6 16 0.0078 63 75 FF 215
1LE1002-1BB23-4FA0 2.2 5.3 2.6 16 0.0102 58 70 FF 215
1LE1002-1CB03-4FA0 2.3 6.2 2.7 16 0.0186 64 76 FF 265
1LE1002-1CB23-4FA0 2.5 6.6 2.9 16 0.02371 64 76 FF 265
1LE1002-1DB23-4FA0 2.3 6.4 3.1 16 0.04395 64 76 FF 300
1LE1002-1DB43-4FA0 2.5 7 3.4 16 0.05616 64 76 FF 300
1LE1002-1BB23-4FB0 2.2 5.3 2.6 16 0.0102 58 70 FF 215
1LE1002-1CB03-4FB0 2.3 6.2 2.7 16 0.0186 64 76 FF 265
1LE1002-1CB23-4FB0 2.5 6.6 2.9 16 0.02371 64 76 FF 265
1LE1002-1DB23-4FB0 2.3 6.4 3.1 16 0.04395 64 76 FF 300
1LE1002-1DB43-4FB0 2.5 7 3.4 16 0.05616 64 76 FF 300
• With flange: IM B35
1LE1002-1CB03-4JA0 2.3 6.2 2.7 16 0.0186 64 76 FF 265
1LE1002-1CB23-4JA0 2.5 6.6 2.9 16 0.02371 64 76 FF 265
1LE1002-1DB23-4JA0 2.3 6.4 3.1 16 0.04395 64 76 FF 300
1LE1002-1DB43-4JA0 2.5 7 3.4 16 0.05616 64 76 FF 300
1)
2)

© Siemens AG 2007

New Generation 1LE1

size

230 V∆/400 VY, 50 Hz; 460 VY, 60 Hz
1.5 1.75 100 L 940 15.3 74 72.6 0.77 3.8 1LE1002-1AC42-2AA0 19
2.2 2.55 112 M 930 23 78 78.1 0.77 5.3 1LE1002-1BC22-2AA0 25
3 3.45 132 S 955 30 80 79.4 0.74 7.3 1LE1002-1CC02-2AA0 34
4 4.6 132 M 950 40 83 83.4 0.76 9.2 1LE1002-1CC22-2AA0 39
5.5 6.3 132 M 950 55 85 85.3 0.75 12.4 1LE1002-1CC32-2AA0 48
1.5 1.75 100 L 940 15.3 74 72.6 0.77 3.8 1LE1002-1AC42-2FA0 20
2.2 2.55 112 M 930 23 78 78.1 0.77 5.3 1LE1002-1BC22-2FA0 26
3 3.45 132 S 955 30 80 79.4 0.74 7.3 1LE1002-1CC02-2FA0 39
4 4.6 132 M 950 40 83 83.4 0.76 9.2 1LE1002-1CC22-2FA0 44
1.5 1.75 100 L 940 15.3 74 72.6 0.77 3.8 1LE1002-1AC42-2FB0 20
2.2 2.55 112 M 930 23 78 78.1 0.77 5.3 1LE1002-1BC22-2FB0 26
3 3.45 132 S 955 30 80 79.4 0.74 7.3 1LE1002-1CC02-2FB0 39
1.5 1.75 100 L 940 15.3 74 72.6 0.77 3.8 1LE1002-1AC42-2KA0 21
2.2 2.55 112 M 930 23 78 78.1 0.77 5.3 1LE1002-1BC22-2KA0 27
400 V∆/690 VY, 50 Hz; 460 V∆, 60 Hz
3 3.45 132 S 955 30 80 79.4 0.74 7.3 1LE1002-1CC03-4AA0 34
4 4.6 132 M 950 40 83 83.4 0.76 9.2 1LE1002-1CC23-4AA0 39
5.5 6.3 132 M 950 55 85 85.3 0.75 12.4 1LE1002-1CC33-4AA0 48
7.5 8.6 160 M 970 75 86 85.4 0.73 17.2 1LE1002-1DC23-4AA0 72
11 12.6 160 L 965 110 87.6 87.9 0.77 23.5 1LE1002-1DC43-4AA0 92
3 3.45 132 S 955 30 80 79.4 0.74 7.3 1LE1002-1CC03-4AB0 34
4 4.6 132 M 950 40 83 83.4 0.76 9.2 1LE1002-1CC23-4AB0 39
5.5 6.3 132 M 950 55 85 85.3 0.75 12.4 1LE1002-1CC33-4AB0 48
7.5 8.6 160 M 970 75 86 86.5 0.73 17.2 1LE1002-1DC23-4AB0 72
11 12.6 160 L 965 110 87.6 87.9 0.77 23.5 1LE1002-1DC43-4AB0 92
3 3.45 132 S 955 30 80 79.4 0.74 7.3 1LE1002-1CC03-4FA0 39
4 4.6 132 M 950 40 83 83.4 0.76 9.2 1LE1002-1CC23-4FA0 44
5.5 6.3 132 M 950 55 85 85.3 0.75 12.4 1LE1002-1CC33-4FA0 53
7.5 8.6 160 M 970 75 86 85.4 0.73 17.2 1LE1002-1DC23-4FA0 81
11 12.6 160 L 965 110 87.6 87.9 0.77 23.5 1LE1002-1DC43-4FA0 101
4 4.6 132 M 950 40 83 83.4 0.76 9.2 1LE1002-1CC23-4FB0 44
5.5 6.3 132 M 950 55 85 85.3 0.75 12.4 1LE1002-1CC33-4FB0 53
7.5 8.6 160 M 970 75 86 85.4 0.73 17.2 1LE1002-1DC23-4FB0 81
11 12.6 160 L 965 110 87.6 87.9 0.77 23.5 1LE1002-1DC43-4FB0 101

2)
3)

© Siemens AG 2007

New Generation 1LE1

class
Moment
of inertia
according
1
at 50 Hz 50 Hz
kgm2 dB(A) dB(A)
230 V∆/400 VY, 50 Hz; 460 VY, 60 Hz
1LE1002-1AC42-2AA0 2.1 4.1 2.4 16 0.0065 61 73
1LE1002-1BC22-2AA0 2.1 4.1 2.4 16 0.0065 61 73
1LE1002-1CC02-2AA0 2 4.6 2.6 16 0.0167 63 75
1LE1002-1CC22-2AA0 2.1 4.7 2.5 16 0.02116 63 75
1LE1002-1CC32-2AA0 2.5 5.2 2.8 16 0.02734 63 75
1LE1002-1AC42-2FA0 2.1 4.1 2.4 16 0.0065 61 73 FF 215
1LE1002-1BC22-2FA0 2.3 4.1 2.5 16 0.0092 68 80 FF 215
1LE1002-1CC02-2FA0 2 4.6 2.6 16 0.0167 63 75 FF 265
1LE1002-1CC22-2FA0 2.1 4.7 2.5 16 0.02116 63 75 FF 265
1LE1002-1AC42-2FB0 2.1 4.1 2.4 16 0.0065 61 73 FF 215
1LE1002-1BC22-2FB0 2.3 4.1 2.5 16 0.0092 68 80 FF 215
1LE1002-1CC02-2FB0 2 4.6 2.6 16 0.0167 63 75 FF 265
1LE1002-1AC42-2KA0 2.1 4.1 2.4 16 0.0065 61 73 FT 130
1LE1002-1BC22-2KA0 2.3 4.1 2.5 16 0.0092 68 80 FT 130
400 V∆/690 VY, 50 Hz; 460 V∆, 60 Hz
1LE1002-1CC03-4AA0 2 4.6 2.6 16 0.017 63 75
1LE1002-1CC23-4AA0 2.1 4.7 2.5 16 0.02116 63 75
1LE1002-1CC33-4AA0 2.5 5.2 2.8 16 0.02734 63 75
1LE1002-1DC23-4AA0 2.1 5.5 2.9 16 0.04993 68 80
1LE1002-1DC43-4AA0 2.2 5.4 2.8 16 0.0678 68 80
1LE1002-1CC03-4AB0 2 4.6 2.6 16 0.0167 63 75
1LE1002-1CC23-4AB0 2.1 4.7 2.5 16 0.02116 63 75
1LE1002-1CC33-4AB0 2.5 5.2 2.8 16 0.02734 63 75
1LE1002-1DC23-4AB0 2.1 5.5 2.9 16 0.04993 68 80
1LE1002-1DC43-4AB0 2.2 5.4 2.8 16 0.0678 68 80
1LE1002-1CC03-4FA0 2 4.6 2.6 16 0.0167 63 75 FF 265
1LE1002-1CC23-4FA0 2.1 4.7 2.5 16 0.02116 63 75 FF 265
1LE1002-1CC33-4FA0 2.5 5.2 2.8 16 0.02734 63 75 FF 265
1LE1002-1DC23-4FA0 2.1 5.5 2.9 16 0.04993 68 80 FF 300
1LE1002-1DC43-4FA0 2.2 5.4 2.8 16 0.0678 68 80 FF 300
1LE1002-1CC23-4FB0 2.1 4.7 2.5 16 0.02116 63 75 FF 265
1LE1002-1CC33-4FB0 2.5 5.2 2.8 16 0.02734 63 75 FF 265
1LE1002-1DC23-4FB0 2.1 5.5 2.9 16 0.04993 68 80 FF 300
1LE1002-1DC43-4FB0 2.2 5.4 2.8 16 0.0678 68 80 FF 300

2)
3)

© Siemens AG 2007

New Generation 1LE1

size
50 Hz 60 Hz Rated Rated Efficiency Efficiency Efficiency Power Rated For Order No. supplements IM B3 IM B3
speed at torque at Class at at factor at current at for voltage, type of con- type of type of
50 Hz 50 Hz accord- 50 Hz 50 Hz 50 Hz 400 V. struction, motor protection construc- construc-
ing 4/4-load 3/4-load 4/4-load 50 Hz and connection box, see tion tion
to CEMEP table from Page 1/56. approx.
3 3.45 100 L 2835 10 EFF2 83.2 84.8 0.87 6 1LE1002-1AA4$
$-$
$$$$ 20
4 4.6 112 M 2930 13 EFF2 84.8 84.4 0.86 7.9 1LE1002-1BA2$
$-$
$$$$ 25
5.5 6.3 132 S 2905 18 EFF2 86 86.6 0.89 10.4 1LE1002-1CA0$
$-$
$$$$ 35
7.5 8.6 132 S 2925 24 EFF2 87.6 87.8 0.88 14 1LE1002-1CA1$
$-$
$$$$ 40
11 12.6 160 M 2920 36 EFF2 88.4 88.7 0.85 21 1LE1002-1DA2$
$-$
$$$$ 60
15 17.3 160 M 2930 49 EFF2 89.5 89.6 0.84 29 1LE1002-1DA3$
$-$
$$$$ 68
18.5 21.3 160 L 2935 60 EFF2 90.9 91 0.86 34 1LE1002-1DA4$
$-$
$$$$ 78
2.2 2.55 100 L 1425 14.8 EFF2 81 84 0.81 4.85 1LE1002-1AB4$
$-$
$$$$ 18
3 3.45 100 L 1425 20.2 EFF2 82.8 83.6 0.85 6.2 1LE1002-1AB5$
$-$
$$$$ 22
4 4.6 112 M 1435 27 EFF2 84.2 85.1 0.84 8.2 1LE1002-1BB2$
$-$
$$$$ 27
5.5 6.3 132 S 1450 36 EFF2 86 86.5 0.83 11.2 1LE1002-1CB0$
$-$
$$$$ 38
7.5 8.6 132 M 1450 49 EFF2 87 87.4 0.83 15 1LE1002-1CB2$
$-$
$$$$ 44
11 12.6 160 M 1460 72 EFF2 88.4 88.1 0.82 22 1LE1002-1DB2$
$-$
$$$$ 62
15 17.3 160 L 1460 98 EFF2 89.4 89.7 0.82 29.5 1LE1002-1DB4$
$-$
$$$$ 73
1.5 1.75 100 L 940 15.3 74 72.6 0.77 3.8 1LE1002-1AC4$
$-$
$$$$ 19
2.2 2.55 112 M 930 23 78 78.1 0.77 5.3 1LE1002-1BC2$
$-$
$$$$ 25
3 3.45 132 S 955 30 80 79.4 0.74 7.3 1LE1002-1CC0$
$-$
$$$$ 34
4 4.6 132 M 950 40 83 83.4 0.76 9.2 1LE1002-1CC2$
$-$
$$$$ 39
5.5 6.3 132 M 950 55 85 85.3 0.75 12.4 1LE1002-1CC3$
$-$
$$$$ 48
7.5 8.6 160 M 970 75 86 85.4 0.73 17.2 1LE1002-1DC2$
$-$
$$$$ 72
11 12.6 160 L 965 110 87.6 87.9 0.77 23.5 1LE1002-1DC4$
$-$
$$$$ 92
0.75 0.86 100 L 695 10.4 66 60.2 0.65 2.45 1LE1002-1AD4$
$-$
$$$$ 17
1.1 1.3 100 L 695 15.1 70.2 67.6 0.65 3.5 1LE1002-1AD5$
$-$
$$$$ 22
1.5 1.75 112 M 675 20 69.5 69.7 0.71 4.4 1LE1002-1BD2$
$-$
$$$$ 25
2.2 2.55 132 S 720 30 78.8 76.4 0.65 6.2 1LE1002-1CD0$
$-$
$$$$ 37
3 3.45 132 M 715 40 78.5 77.9 0.65 8.5 1LE1002-1CD2$
$-$
$$$$ 44
4 4.6 160 M 720 53 80 78.7 0.69 10.4 1LE1002-1DD2$
$-$
$$$$ 60
5.5 6.3 160 M 720 73 83.5 83.9 0.70 13.6 1LE1002-1DD3$
$-$
$$$$ 72
7.5 8.6 160 L 715 100 83.5 84.7 0.70 18.6 1LE1002-1DD4$
$-$
$$$$ 91
Order No. supplements, see from Page 1/56.

© Siemens AG 2007

New Generation 1LE1

Order No. Locked-rotor
torque
Locked-rotor
current
Breakdown
torque
Torque class Moment
of inertia
Noise at rated output 1
with direct starting as multiple of rated Measuring- Sound pressure
torque current torque surface sound level at 50 Hz
pressure level
at 50 Hz

kgm2 dB(A) dB(A)
1LE1002-1AA4$
$-$
$$$$ 3.2 6.2 3.3 16 0.0034 72 84
1LE1002-1BA2$
$-$
$$$$ 2.7 7.3 3.7 16 0.0067 69 81
1LE1002-1CA0$
$-$
$$$$ 2 5.6 2.6 16 0.01267 68 80
1LE1002-1CA1$
$-$
$$$$ 2.2 6.4 3 16 0.01601 68 80
1LE1002-1DA2$
$-$
$$$$ 2.1 6.1 2.7 16 0.02971 70 82
1LE1002-1DA3$
$-$
$$$$ 2.5 6.1 3.2 16 0.03619 70 82
1LE1002-1DA4$
$-$
$$$$ 2.5 7 3.2 16 0.04395 70 82
1LE1002-1AB4$
$-$
$$$$ 2.3 5.1 2.7 16 0.0059 63 75
1LE1002-1AB5$
$-$
$$$$ 2.4 5.4 2.6 16 0.0078 63 75
1LE1002-1BB2$
$-$
$$$$ 2.2 5.3 2.6 16 0.0102 58 70
1LE1002-1CB0$
$-$
$$$$ 2.3 6.2 2.7 16 0.0186 64 76
1LE1002-1CB2$
$-$
$$$$ 2.5 6.6 2.9 16 0.02371 64 76
$-$
1LE1002-1DB2$ $$$$ 2.3 6.4 3.1 16 0.04395 64 76
1LE1002-1DB4$
$-$
$$$$ 2.5 7 3.4 16 0.05616 64 76
1LE1002-1AC4$
$-$
$$$$ 2.1 4.1 2.4 16 0.0065 61 73
1LE1002-1BC2$
$-$
$$$$ 2.3 4.1 2.5 16 0.0092 68 80
1LE1002-1CC0$
$-$
$$$$ 2 4.6 2.6 16 0.0167 63 75
1LE1002-1CC2$
$-$
$$$$ 2.1 4.7 2.5 16 0.02116 63 75
1LE1002-1CC3$
$-$
$$$$ 2.5 5.2 2.8 16 0.02734 63 75
1LE1002-1DC2$
$-$
$$$$ 2.1 5.5 2.9 16 0.04993 68 80
1LE1002-1DC4$
$-$
$$$$ 2.2 5.4 2.8 16 0.0678 68 80
1LE1002-1AD4$
$-$
$$$$ 1.8 2.8 2 16 0.0056 66 78
1LE1002-1AD5$
$-$
$$$$ 1.5 2.9 1.8 16 0.0078 66 78
1LE1002-1BD2$
$-$
$$$$ 1.8 3.0 1.9 16 0.0094 66 78
1LE1002-1CD0$
$-$
$$$$ 1.5 3.5 2.1 13 0.0186 53 65
1LE1002-1CD2$
$-$
$$$$ 1.5 3.3 2 13 0.02372 53 65
1LE1002-1DD2$
$-$
$$$$ 1.7 3.8 2.3 13 0.0439 68 80
1LE1002-1DD3$
$-$
$$$$ 1.6 4 2.2 13 0.0562 68 80
1LE1002-1DD4$
$-$
$$$$ 1.7 3.8 2.2 13 0.0772 68 80

© Siemens AG 2007

New Generation 1LE1

1 Order No. supplements
Motor type Frame Positions 12 and 13: Voltages (voltage codes)
size Standard voltages Further voltages
50 Hz 50 Hz
230 V∆/400 VY 400 V∆/690 VY 500 VY 500 V∆ 220 V∆/380 VY 380 V∆/660 VY 415 VY 415 V∆
60 Hz Rated voltage range
460 VY 460 V∆ (210 … 230 V∆/ (360 … 400 V∆/ (395 … 435 VY) 1) (395 … 435 V∆) 1)
360 … 400 VY) 1) 625 … 695 VY) 1)
see “Selection and ordering data” for
outputs at 60 Hz
22 34 27 40 21 33 23 35
1LE1002-1A..$
$-$
$… 100 L " " " " ✓ ✓ ✓ ✓
1LE1002-1B..$
$-$
$… 112 M " " " " ✓ ✓ ✓ ✓
1LE1002-1C..$
$-$
$… 132 S/M " " " " ✓ ✓ ✓ ✓
1LE1002-1D..$
$-$
$… 160 M/L " " " " ✓ ✓ ✓ ✓
" Without additional charge Order other voltages with voltage code 9 in position 12, code 0
✓ With additional charge in position 13 and the corresponding order code (see “Special
versions” in the “Selection and ordering data” under “Voltages”,
Page 1/78).
Motor type Frame Position 14: Types of construction (type letter)

size Without flange With flange (acc. to DIN EN 50347)
IM B3 IM B6 IM B7 IM B8 IM V6 IM V5 IM V5 Flange IM B5 IM V1 IM V1 IM V3 IM B35
2) 3) 3) 3) 3) 3) 3) 6) 3)
without with size without with
protec- protec- protec- protec-
tive tive tive tive
cover cover cover cover
3) 3) 4) 5) 3) 3) 4) 5)
A T U V D C C F G G H J
Order No. – – – – – – -Z – – -Z – –
supplement -Z H00 H00
with order
code
1LE1002-1A...-.$
$.. 100 L # # # # # # ✓ FF 215 ✓ ✓ ✓ ✓ ✓
1LE1002-1B...-.$
$.. 112 M # # # # # # ✓ FF 215 ✓ ✓ ✓ ✓ ✓
1LE1002-1C...-.$
$.. 132 S/M # # # # # # ✓ FF 265 ✓ ✓ ✓ ✓ ✓
1LE1002-1D...-.$
$.. 160 M/L # # # # # # ✓ FF 300 ✓ ✓ ✓ ✓ ✓

size With standard flange (acc. to DIN EN 50347)
Flange size IM B14 IM V19 IM V18 IM V18 IM B34
3) 7) 3)
without with protective
protective cover 3) cover 3) 4) 5)
K L M M N
Order No. – – – -Z –
supplement -Z H00
with order
code
1LE1002-1A...-.$
$.. 100 L FT 130 ✓ ✓ ✓ ✓ ✓
1LE1002-1B...-.$
$.. 112 M FT 130 ✓ ✓ ✓ ✓ ✓
1LE1002-1C...-.$
$.. 132 S/M FT 165 ✓ ✓ ✓ ✓ ✓
1LE1002-1D...-.$
$.. 160 M/L FT 215 ✓ ✓ ✓ ✓ ✓
# Standard version
✓ With additional charge
1) 6)
A rated voltage range is also specified on the rating plate. The types of construction IM V3 and IM V1 without protective cover/with
2)
The types of construction IM B6/7/8, IM V6 and IM V5 without protective protective cover are also possible as long as no condensation drainage
cover/with protective cover are also possible as long as no condensation holes (order code H03) and no stamping of these types of construction on
drainage holes (order code H03) and no stamping of these types of con- the rating plate are required. As standard, the type of construction IM B5 is
struction on the rating plate are required. As standard, the type of con- then stamped on the rating plate. With type of construction IM V1 with pro-
struction IM B3 is then stamped on the rating plate. With type of tective cover, the protective cover has to be additionally ordered with
construction IM V5 with protective cover, the protective cover has to be order code H00. The protective cover is not stamped on the rating plate.
7)
additionally ordered with order code H00. The protective cover is not The types of construction IM V19 and IM V18 without protective cover/with
stamped on the rating plate. protective cover are also possible as long as no condensation drainage
3)
The type of construction is stamped on the rating plate. When ordering holes (order code H03) and no stamping of these types of construction on
with condensation drainage holes (order code H03), it is absolutely neces- the rating plate are required. As standard, the type of construction IM B14
sary to specify the type of construction for the exact position of the con- is then stamped on the rating plate. With type of construction IM V18 with
densation drainage holes during manufacture. protective cover, the protective cover has to be additionally ordered with
4)
order code H00. The protective cover is not stamped on the rating plate.
Option second shaft end (Order code) L05 not possible.
5) In combination with an encoder, it is not necessary to order the protective
cover (order code H00), as this is delivered as a protection for the encoder
as standard. In this case, the protective cover is standard design (without
additional charge).

© Siemens AG 2007

New Generation 1LE1

Motor type Frame
size
Position 15: Motor protection (motor protection letter) 1
Without Motor protection Motor protection Motor tempera- NTC thermistors Temperature
motor with PTC ther- with PTC ther- ture detection for tripping detectors for
protection mistors with mistors with with embedded tripping 1)
3 embedded 6 embedded temperature
temperature temperature sen- sensor
sensors for sors for alarm KTY 84-130 1)
tripping 1) and tripping 1)
A B C F Z Z
Order code Q2A Q3A
1LE1002-1A...-..$
$. 100 L # ✓ ✓ ✓ ✓ ✓
1LE1002-1B...-..$
$. 112 M # ✓ ✓ ✓ ✓ ✓
1LE1002-1C...-..$
$. 132 S/M # ✓ ✓ ✓ ✓ ✓
1LE1002-1D...-..$
$. 160 M/L # ✓ ✓ ✓ ✓ ✓
# Standard version
Motortyp Frame Position 16: Connection box (connection box code)

size
Connection box Connection box Connection box Connection box
top 2) on RHS 3) on LHS 3) bottom 3)
4 5 6 7
1LE1002-1A...-...$
$ 100 L # ✓ ✓ ✓
1LE1002-1B...-...$
$ 112 M # ✓ ✓ ✓
$
1LE1002-1C...-...$ 132 S/M # ✓ ✓ ✓
1LE1002-1D...-...$
$ 160 M/L # ✓ ✓ ✓
# Standard version
1) For appropriate tripping unit, see Catalog LV 1.

2) With type of construction, cast feet as standard. Screwed-on feet are
available with order code H01, see “Special versions”.
3) With type of construction, screwed-on feet as standard.

© Siemens AG 2007

New Generation 1LE1

size
3 3.45 100 L 2905 9.9 EFF1 86.7 87.5 0.84 5.9 1LE1001-1AA4$
$-$
$$$$ 21
4 4.6 112 M 2950 13 EFF1 88 88.5 0.86 7.4 1LE1001-1BA2$
$-$
$$$$ 27
5.5 6.3 132 S 2950 18 EFF1 89.5 90.6 0.87 10.2 1LE1001-1CA0$
$-$
$$$$ 39
7.5 8.6 132 S 2950 24 EFF1 90 91 0.87 13.8 1LE1001-1CA1$
$-$
$$$$ 43
11 12.6 160 M 2955 36 EFF1 90.8 91 0.87 20 1LE1001-1DA2$
$-$
$$$$ 67
15 17.3 160 M 2955 48 EFF1 91.4 91.5 0.88 27 1LE1001-1DA3$
$-$
$$$$ 75
18.5 21.3 160 L 2955 60 EFF1 92 92.5 0.88 33 1LE1001-1DA4$
$-$
$$$$ 84
2.2 2.55 100 L 1455 14 EFF1 86.4 87 0.81 4.55 1LE1001-1AB4$
$-$
$$$$ 21
3 3.45 100 L 1455 20 EFF1 87.4 88 0.82 6 1LE1001-1AB5$
$-$
$$$$ 25
4 4.6 112 M 1460 26 EFF1 88.3 88.5 0.81 8.1 1LE1001-1BB2$
$-$
$$$$ 29
5.5 6.3 132 S 1465 36 EFF1 89.2 89.5 0.80 11.2 1LE1001-1CB0$
$-$
$$$$ 42
7.5 8.6 132 M 1465 49 EFF1 90.1 91 0.83 14.4 1LE1001-1CB2$
$-$
$$$$ 49
11 12.6 160 M 1470 71 EFF1 91.2 91.8 0.85 20.5 1LE1001-1DB2$
$-$
$$$$ 71
15 17.3 160 L 1475 97 EFF1 92 92.4 0.85 27.5 1LE1001-1DB4$
$-$
$$$$ 83
1.5 1.75 100 L 970 15 84.5 84.6 0.73 3.5 1LE1001-1AC4$
$-$
$$$$ 25
2.2 2.55 112 M 965 22 85 86.5 0.75 5 1LE1001-1BC2$
$-$
$$$$ 29
3 3.45 132 S 970 30 86 85.6 0.74 6.9 1LE1001-1CC0$
$-$
$$$$ 38
4 4.6 132 M 970 39 86 86.5 0.78 8.6 1LE1001-1CC2$
$-$
$$$$ 43
5.5 6.3 132 M 970 54 88 89 0.77 11.8 1LE1001-1CC3$
$-$
$$$$ 52
7.5 8.6 160 M 975 73 89 89.6 0.77 15.8 1LE1001-1DC2$
$-$
$$$$ 77
11 12.6 160 L 975 108 89.5 90.5 0.80 22 1LE1001-1DC4$
$-$
$$$$ 93
0.75 0.86 100 L 725 9.9 67 65 0.57 2.85 1LE1001-1AD4$
$-$
$$$$ 21
1.1 1.3 100 L 725 14 67 64.5 0.57 4.15 1LE1001-1AD5$
$-$
$$$$ 25
1.5 1.75 112 M 715 20 75 75.5 0.65 4.45 1LE1001-1BD2$
$-$
$$$$ 29
2.2 2.55 132 S 725 29 77.5 76.7 0.63 6.5 1LE1001-1CD0$
$-$
$$$$ 41
3 3.45 132 M 720 40 81 82 0.64 8.4 1LE1001-1CD2$
$-$
$$$$ 49
4 4.6 160 M 730 52 87 88 0.69 9.6 1LE1001-1DD2$
$-$
$$$$ 69
5.5 6.3 160 M 735 72 87.5 89 0.69 13.2 1LE1001-1DD3$
$-$
$$$$ 82
7.5 8.6 160 L 730 98 88 89 0.72 17 1LE1001-1DD4$
$-$
$$$$ 94

© Siemens AG 2007

New Generation 1LE1

torque
Locked-rotor
current
Breakdown
torque
Torque class Moment
of inertia
pressure level
at 50 Hz

kgm2 dB(A) dB(A)
1LE1001-1AA4$
$-$
$$$$ 2.3 7 3.3 16 0.0044 72 84
1LE1001-1BA2$
$-$
$$$$ 2.4 7.4 3.3 16 0.0092 69 81
1LE1001-1CA0$
$-$
$$$$ 1.8 6.7 2.9 16 0.02012 68 80
1LE1001-1CA1$
$-$
$$$$ 2.2 7.5 3.1 16 0.02353 68 80
1LE1001-1DA2$
$-$
$$$$ 2.1 7.4 3.2 16 0.04471 70 82
1LE1001-1DA3$
$-$
$$$$ 2.4 7.6 3.4 16 0.05277 70 82
1LE1001-1DA4$
$-$
$$$$ 2.9 7.9 3.6 16 0.06085 70 82
1LE1001-1AB4$
$-$
$$$$ 2.1 6.9 3.3 16 0.0086 63 75
1LE1001-1AB5$
$-$
$$$$ 2 6.9 3.1 16 0.0109 63 75
1LE1001-1BB2$
$-$
$$$$ 2.5 7.1 3.2 16 0.014 58 70
1LE1001-1CB0$
$-$
$$$$ 2.3 6.9 2.9 16 0.02698 64 76
1LE1001-1CB2$
$-$
$$$$ 2.3 6.9 2.9 16 0.03353 64 76
$-$
1LE1001-1DB2$ $$$$ 2.2 6.7 2.8 16 0.06495 64 76
1LE1001-1DB4$
$-$
$$$$ 2.5 7.3 3 16 0.08281 64 76
1LE1001-1AC4$
$-$
$$$$ 2 6.2 2.9 16 0.0113 61 73
1LE1001-1BC2$
$-$
$$$$ 2.1 6 3.1 16 0.0139 68 80
1LE1001-1CC0$
$-$
$$$$ 1.6 5.6 2.6 13 0.02371 63 75
1LE1001-1CC2$
$-$
$$$$ 1.6 5.6 2.5 13 0.02918 63 75
1LE1001-1CC3$
$-$
$$$$ 1.9 6.1 2.8 16 0.03673 63 75
1LE1001-1DC2$
$-$
$$$$ 1.8 6.3 2.8 16 0.0754 68 80
1LE1001-1DC4$
$-$
$$$$ 1.7 6.2 2.7 16 0.0975 68 80
1LE1001-1AD4$
$-$
$$$$ 1.5 3.8 2.6 13 0.0086 66 78
1LE1001-1AD5$
$-$
$$$$ 1.7 3.8 2.9 13 0.0109 66 78
1LE1001-1BD2$
$-$
$$$$ 1.4 3.6 2 13 0.014 66 78
1LE1001-1CD0$
$-$
$$$$ 1.4 3.6 1.8 10 0.02698 53 65
1LE1001-1CD2$
$-$
$$$$ 1.6 3.9 2.1 10 0.03463 53 65
1LE1001-1DD2$
$-$
$$$$ 1.8 4.3 2 13 0.0649 68 80
1LE1001-1DD3$
$-$
$$$$ 2.1 4.4 2.1 13 0.0828 68 80
1LE1001-1DD4$
$-$
$$$$ 1.9 4.5 2.1 13 0.0982 68 80

© Siemens AG 2007

New Generation 1LE1

50 Hz 50 Hz
460 VY 460 V∆ (210 … 230 V∆/ (360 … 400 V∆/ (395 … 435 VY) 1) (395 … 435 V∆) 1)
360 … 400 VY) 1) 625 … 695 VY) 1)
outputs at 60 Hz
22 34 27 40 21 33 23 35
1LE1001-1A..$
$-$
$… 100 L " " " " ✓ ✓ ✓ ✓
1LE1001-1B..$
$-$
$… 112 M " " " " ✓ ✓ ✓ ✓
1LE1001-1C..$
$-$
$… 132 S/M " " " " ✓ ✓ ✓ ✓
1LE1001-1D..$
$-$
$… 160 M/L " " " " ✓ ✓ ✓ ✓
Page 1/78).

2) 3) 3) 3) 3) 3) 3) 6) 3)
tive tive tive tive
3) 3) 4) 5) 3) 3) 4) 5)
Order No. – – – – – – -Z – – -Z – –
with order
code
1LE1001-1A...-.$
$.. 100 L # # # # # # ✓ FF 215 ✓ ✓ ✓ ✓ ✓
1LE1001-1B...-.$
$.. 112 M # # # # # # ✓ FF 215 ✓ ✓ ✓ ✓ ✓
1LE1001-1C...-.$
$.. 132 S/M # # # # # # ✓ FF 265 ✓ ✓ ✓ ✓ ✓
1LE1001-1D...-.$
$.. 160 M/L # # # # # # ✓ FF 300 ✓ ✓ ✓ ✓ ✓

3) 7) 3)
K L M M N
supplement -Z H00
with order
code
1LE1001-1A...-.$
$.. 100 L FT 130 ✓ ✓ ✓ ✓ ✓
1LE1001-1B...-.$
$.. 112 M FT 130 ✓ ✓ ✓ ✓ ✓
1LE1001-1C...-.$
$.. 132 S/M FT 165 ✓ ✓ ✓ ✓ ✓
1LE1001-1D...-.$
$.. 160 M/L FT 215 ✓ ✓ ✓ ✓ ✓
# Standard version
1) A rated voltage range is also specified on the rating plate. 6) The types of construction IM V3 and IM V1 without protective cover/with
2) The types of construction IM B6/7/8, IM V6 and IM V5 without protective protective cover are also possible as long as no condensation drainage
7)
3) The type of construction is stamped on the rating plate. When ordering holes (order code H03) and no stamping of these types of construction on
4)
5)
In combination with an encoder, it is not necessary to order the protective
additional charge).

© Siemens AG 2007

New Generation 1LE1

Motor type Frame
size
Position 15: Motor protection (motor protection letter)
1
motor protection with PTC ther- with PTC ther- ture detection for tripping detectors for
mistors with mistors with with embedded tripping 1)
temperature temperature sensor
sensors sensors KTY 84-130 1)
for tripping 1) for alarm and
1)
tripping
A B C F Z Z
Order code Q2A Q3A
1LE1001-1A...-..$
$. 100 L # ✓ ✓ ✓ ✓ ✓
1LE1001-1B...-..$
$. 112 M # ✓ ✓ ✓ ✓ ✓
1LE1001-1C...-..$
$. 132 S/M # ✓ ✓ ✓ ✓ ✓
1LE1001-1D...-..$
$. 160 M/L # ✓ ✓ ✓ ✓ ✓
# Standard version
Motor type Frame Position 16: Connection box (connection box code)
size Connection box Connection box Connection box Connection box
4 5 6 7
1LE1001-1A...-...$
$ 100 L # ✓ ✓ ✓
1LE1001-1B...-...$
$ 112 M # ✓ ✓ ✓
1LE1001-1C...-...$
$ 132 S/M # ✓ ✓ ✓
1LE1001-1D...-...$
$ 160 M/L # ✓ ✓ ✓
# Standard version

2) With type of construction, cast feet as standard. Screwed-on feet are
3) With type of construction, screwed-on feet as standard.

© Siemens AG 2007

New Generation 1LE1
Self-ventilated motors with increased output
and improved efficiency

size
Motor version: temperature class 155 (F), IP55 degree of protection, with increased output, used acc. to temperature class 130 (B)
4 4,6 100 L 2850 13.3 EFF2 85.6 86.7 0.85 7.9 1LE1002-1AA6$
$-$
$$$$ 25
5.5 6.3 112 M 2935 18 EFF2 87 86.8 0.86 10.6 1LE1002-1BA6$
$-$
$$$$ 31
11 12.6 132 M 2920 36 EFF2 90 90.7 0.90 19.6 1LE1002-1CA6$
$-$
$$$$ 53
22 24.5 160 L 2930 72 EFF2 91.6 91.4 0.88 39.5 1LE1002-1DA6$
$-$
$$$$ 85
4 4.6 100 L 1430 26.8 EFF2 84.2 85.1 0.81 8.5 1LE1002-1AB6$
$-$
$$$$ 27
5.5 6.3 112 M 1435 37 EFF2 85.7 86.5 0.84 11 1LE1002-1BB6$
$-$
$$$$ 33
11 12.6 132 M 1450 72 EFF2 88.8 89.3 0.84 21.5 1LE1002-1CB6$
$-$
$$$$ 58
18.5 21.3 160 L 1460 121 EFF2 90 90.2 0.85 35 1LE1002-1DB6$
$-$
$$$$ 85
2.2 2.55 100 L 930 22.5 76 76.7 0.79 5.3 1LE1002-1AC6$
$-$
$$$$ 24
3 3.45 112 M 945 30 79 78.2 0.72 7.6 1LE1002-1BC6$
$-$
$$$$ 32
7.5 8.6 132 M 950 75 85.5 85.7 0.74 17.2 1LE1002-1CC6$
$-$
$$$$ 54
15 17.3 160 L 965 148 88 88 0.75 33 1LE1002-1DC6$
$-$
$$$$ 109

© Siemens AG 2007

New Generation 1LE1

torque
Locked-rotor
current
Breakdown
torque
Torque class Moment
of inertia
pressure level
at 50 Hz

kgm2 dB(A) dB(A)
1LE1002-1AA6$
$-$
$$$$ 4.5 7 4.1 16 0.0044 72 84
1LE1002-1BA6$
$-$
$$$$ 3.5 7.5 4.3 16 0.0085 69 81
1LE1002-1CA6$
$-$
$$$$ 2.8 7.5 3.7 16 0.02233 68 80
1LE1002-1DA6$
$-$
$$$$ 2.6 7.5 3.4 16 0.04913 70 82
1LE1002-1AB6$
$-$
$$$$ 2.9 5.8 3.1 16 0.01 63 75
1LE1002-1BB6$
$-$
$$$$ 2.6 6.8 2.8 16 0.0124 58 70
1LE1002-1CB6$
$-$
$$$$ 2.5 7.2 3 16 0.03259 64 76
1LE1002-1DB6$
$-$
$$$$ 2.7 7.2 3.2 16 0.06843 64 76
1LE1002-1AC6$
$-$
$$$$ 2.2 4 2.3 16 0.0084 61 73
1LE1002-1BC6$
$-$
$$$$ 2.9 4.6 3.0 16 0.0128 68 80
1LE1002-1CC6$
$-$
$$$$ 2.4 5.3 3 16 0.032 63 75
$-$
1LE1002-1DC6$ $$$$ 2.9 6 3.4 16 0.0936 68 80

© Siemens AG 2007

New Generation 1LE1

50 Hz 50 Hz
460 VY 460 V∆ (210 … 230 V∆/ (360 … 400 V∆/ (395 … 435 VY) 1) (395 … 435 V∆) 1)
360 … 400 VY) 1) 625 … 695 VY) 1)
outputs at 60 Hz
22 34 27 40 21 33 23 35
1LE1002-1A..$
$-$
$… 100 L " " " " ✓ ✓ ✓ ✓
1LE1002-1B..$
$-$
$… 112 M " " " " ✓ ✓ ✓ ✓
1LE1002-1C..$
$-$
$… 132 M " " " " ✓ ✓ ✓ ✓
1LE1002-1D..$
$-$
$… 160 L " " " " ✓ ✓ ✓ ✓
Page 1/78).

2) 3) 3) 3) 3) 3) 3) 6) 3)
tive tive tive tive
3) 3) 4) 5) 3) 3) 4) 5)
Order No. – – – – – – -Z – – -Z – –
with order
code
1LE1002-1A...-.$
$.. 100 L # # # # # # ✓ FF 215 ✓ ✓ ✓ ✓ ✓
1LE1002-1B...-.$
$.. 112 M # # # # # # ✓ FF 215 ✓ ✓ ✓ ✓ ✓
1LE1002-1C...-.$
$.. 132 M # # # # # # ✓ FF 265 ✓ ✓ ✓ ✓ ✓
1LE1002-1D...-.$
$.. 160 L # # # # # # ✓ FF 300 ✓ ✓ ✓ ✓ ✓

3) 7) 3) without with protective
K L M M N
supplement -Z H00
with order
code
1LE1002-1A...-.$
$.. 100 L FT 130 ✓ ✓ ✓ ✓ ✓
1LE1002-1B...-.$
$.. 112 M FT 130 ✓ ✓ ✓ ✓ ✓
1LE1002-1C...-.$
$.. 132 M FT 165 ✓ ✓ ✓ ✓ ✓
1LE1002-1D...-.$
$.. 160 L FT 215 ✓ ✓ ✓ ✓ ✓
# Standard version
1) A rated voltage range is also specified on the rating plate. 6) The types of construction IM V3 and IM V1 without protective cover/with
2) The types of construction IM B6/7/8, IM V6 and IM V5 without protective protective cover are also possible as long as no condensation drainage
7)
3)
4)
5)
additional charge).

© Siemens AG 2007

New Generation 1LE1

Motor type Frame
size
1
1)
tripping
A B C F Z Z
Order code Q2A Q3A
1LE1002-1A...-..$
$. 100 L # ✓ ✓ ✓ ✓ ✓
1LE1002-1B...-..$
$. 112 M # ✓ ✓ ✓ ✓ ✓
1LE1002-1C...-..$
$. 132 M # ✓ ✓ ✓ ✓ ✓
1LE1002-1D...-..$
$. 160 L # ✓ ✓ ✓ ✓ ✓
# Standard version
4 5 6 7
1LE1002-1A...-...$
$ 100 L # ✓ ✓ ✓
1LE1002-1B...-...$
$ 112 M # ✓ ✓ ✓
1LE1002-1C...-...$
$ 132 M # ✓ ✓ ✓
1LE1002-1D...-...$
$ 160 L # ✓ ✓ ✓
# Standard version

2)
With type of construction, screwed-on feet as standard.

© Siemens AG 2007

New Generation 1LE1
and high efficiency

size
4 4.6 100 L 2905 13 EFF1 88 89 0.86 7.6 1LE1001-1AA6$
$-$
$$$$ 26
5.5 6.3 112 M 2950 18 EFF1 89 88.5 0.89 10 1LE1001-1BA6$
$-$
$$$$ 34
11 12.6 132 M 2955 36 EFF1 91.5 92.5 0.89 19.4 1LE1001-1CA6$
$-$
$$$$ 57
22 24.5 160 L 2955 71 EFF1 92.8 93.5 0.89 38.5 1LE1001-1DA6$
$-$
$$$$ 94
4 4.6 100 L 1460 26 EFF1 88.3 88.7 0.8 8.2 1LE1001-1AB6$
$-$
$$$$ 30
5.5 6.3 112 M 1460 36 EFF1 89.2 89.7 0.81 11 1LE1001-1BB6$
$-$
$$$$ 34
11 12.6 132 M 1465 72 EFF1 91 91.4 0.84 21 1LE1001-1CB6$
$-$
$$$$ 64
18.5 21.3 160 L 1475 120 EFF1 92.4 92.8 0.85 34 1LE1001-1DB6$
$-$
$$$$ 100
2.2 2.55 100 L 965 22 84.5 85.6 0.76 4.95 1LE1001-1AC6$
$-$
$$$$ 30
3 3.45 112 M 960 30 84.5 84.7 0.79 6.5 1LE1001-1BC6$
$-$
$$$$ 34
7.5 8.6 132 M 970 74 88.5 88.5 0.77 15.4 1LE1001-1CC6$
$-$
$$$$ 64
15 17.3 160 L 975 147 90.6 91 0.81 29.5 1LE1001-1DC6$
$-$
$$$$ 115

© Siemens AG 2007

New Generation 1LE1
and high efficiency

torque
Locked-rotor
current
Breakdown
torque
Torque class Moment
of inertia
pressure level
at 50 Hz

kgm2 dB(A) dB(A)
1LE1001-1AA6$
$-$
$$$$ 2.5 7.6 3.5 16 0.0054 72 84
1LE1001-1BA6$
$-$
$$$$ 2.2 7.7 3.3 16 0.0119 73 85
1LE1001-1CA6$
$-$
$$$$ 2.5 7.9 3.2 16 0.03143 68 80
1LE1001-1DA6$
$-$
$$$$ 3.1 8.4 3.7 16 0.06764 70 82
1LE1001-1AB6$
$-$
$$$$ 2.2 7.5 3.5 16 0.0137 63 75
1LE1001-1BB6$
$-$
$$$$ 2.5 7.1 3.1 16 0.0166 58 70
1LE1001-1CB6$
$-$
$$$$ 2.9 7.7 3.1 16 0.04571 64 76
1LE1001-1DB6$
$-$
$$$$ 2.8 7.7 3.3 16 0.09854 64 76
1LE1001-1AC6$
$-$
$$$$ 1.9 5.7 2.9 16 0.0137 61 73
1LE1001-1BC6$
$-$
$$$$ 2.1 6 3.1 16 0.0166 68 80
1LE1001-1CC6$
$-$
$$$$ 2.1 6.5 3 16 0.04572 63 75
$-$
1LE1001-1DC6$ $$$$ 1.9 6.5 2.9 16 0.01208 68 80

© Siemens AG 2007

New Generation 1LE1
and high efficiency

50 Hz 50 Hz
460 VY 460 V∆ (210 … 230 V∆/ (360 … 400 V∆/ (395 … 435 VY) 1) (395 … 435 V∆) 1)
360 … 400 VY) 1) 625 … 695 VY) 1)
outputs at 60 Hz
22 34 27 40 21 33 23 35
1LE1001-1A..$
$-$
$… 100 L " " " " ✓ ✓ ✓ ✓
1LE1001-1B..$
$-$
$… 112 M " " " " ✓ ✓ ✓ ✓
1LE1001-1C..$
$-$
$… 132 M " " " " ✓ ✓ ✓ ✓
1LE1001-1D..$
$-$
$… 160 L " " " " ✓ ✓ ✓ ✓
Page 1/78).

2) 3) 3) 3) 3) 3) 3) 6) 3)
tive tive tive tive
3) 3) 4) 5) 3) 3) 4) 5)
Order No. – – – – – – -Z – – -Z – –
with order
code
1LE1001-1A...-.$
$.. 100 L # # # # # # ✓ FF 215 ✓ ✓ ✓ ✓ ✓
1LE1001-1B...-.$
$.. 112 M # # # # # # ✓ FF 215 ✓ ✓ ✓ ✓ ✓
1LE1001-1C...-.$
$.. 132 M # # # # # # ✓ FF 265 ✓ ✓ ✓ ✓ ✓
1LE1001-1D...-.$
$.. 160 L # # # # # # ✓ FF 300 ✓ ✓ ✓ ✓ ✓

3) 7) 3)
K L M M N
supplement -Z H00
with order
code
1LE1001-1A...-.$
$.. 100 L FT 130 ✓ ✓ ✓ ✓ ✓
1LE1001-1B...-.$
$.. 112 M FT 130 ✓ ✓ ✓ ✓ ✓
1LE1001-1C...-.$
$.. 132 M FT 165 ✓ ✓ ✓ ✓ ✓
1LE1001-1D...-.$
$.. 160 L FT 215 ✓ ✓ ✓ ✓ ✓
# Standard version
1) 6)
A rated voltage range is also specified on the rating plate. The types of construction IM V3 and IM V1 without protective cover/with
2)
The types of construction IM B6/7/8, IM V6 and IM V5 without protective protective cover are also possible as long as no condensation drainage
7)
3)
4)
5)
additional charge).

© Siemens AG 2007

New Generation 1LE1
and high efficiency

Motor type Frame
size
1
1)
tripping
A B C F Z Z
Order code Q2A Q3A
1LE1001-1A...-..$
$. 100 L # ✓ ✓ ✓ ✓ ✓
1LE1001-1B...-..$
$. 112 M # ✓ ✓ ✓ ✓ ✓
1LE1001-1C...-..$
$. 132 M # ✓ ✓ ✓ ✓ ✓
1LE1001-1D...-..$
$. 160 L # ✓ ✓ ✓ ✓ ✓
# Standard version
4 5 6 7
1LE1001-1A...-...$
$ 100 L # ✓ ✓ ✓
1LE1001-1B...-...$
$ 112 M # ✓ ✓ ✓
1LE1001-1C...-...$
$ 132 M # ✓ ✓ ✓
1LE1001-1D...-...$
$ 160 L # ✓ ✓ ✓
# Standard version

2)

© Siemens AG 2007

New Generation 1LE1
Forced-air cooled motors without external fan and
fan cover with improved efficiency

size
Operating values at rated output Order No. with -Z
and order code
Price Weight
speed at torque at Class at at factor at current at for voltage, type of construc- type of type of
50 Hz 50 Hz accord- 50 Hz 50 Hz 50 Hz 400 V. tion, motor protection and construc- construc-
ing 4/4-load 3/4-load 4/4-load 50 Hz connection box, see table tion tion
to CEMEP from Page 1/72. approx.
3 3.45 100 L 2835 10 EFF2 83.2 84.8 0.87 6 1LE1002-1AA4$
$-$
$$$$-Z 20
F90
4 4.6 112 M 2930 13 EFF2 84.8 84.4 0.86 7.9 1LE1002-1BA2$
$-$
$$$$-Z 25
F90
5.5 6.3 132 S 2905 18 EFF2 86 86.6 0.89 10.4 1LE1002-1CA0$
$-$
$$$$-Z 35
F90
7.5 8.6 132 S 2925 24 EFF2 87.6 87.8 0.88 14 1LE1002-1CA1$
$-$
$$$$-Z 40
F90
11 12.6 160 M 2920 36 EFF2 88.4 88.7 0.85 21 1LE1002-1DA2$
$-$
$$$$-Z 60
F90
15 17.3 160 M 2930 49 EFF2 89.5 89.6 0.84 29 1LE1002-1DA3$
$-$
$$$$-Z 68
F90
18.5 21.3 160 L 2935 60 EFF2 90.9 91 0.86 34 1LE1002-1DA4$
$-$
$$$$-Z 78
F90
2.2 2.55 100 L 1425 14.8 EFF2 81 84 0.81 4.85 $-$
1LE1002-1AB4$ $$$$-Z 18
F90
3 3.45 100 L 1425 20.2 EFF2 82.8 83.6 0.85 6.2 1LE1002-1AB5$
$-$
$$$$-Z 22
F90
4 4.6 112 M 1435 27 EFF2 84.2 85.1 0.84 8.2 1LE1002-1BB2$
$-$
$$$$-Z 27
F90
5.5 6.3 132 S 1450 36 EFF2 86 86.5 0.83 11.2 1LE1002-1CB0$
$-$
$$$$-Z 38
F90
7.5 8.6 132 M 1450 49 EFF2 87 87.4 0.83 15 1LE1002-1CB2$
$-$
$$$$-Z 44
F90
11 12.6 160 M 1460 72 EFF2 88.4 88.1 0.82 22 1LE1002-1DB2$
$-$
$$$$-Z 62
F90
15 17.3 160 L 1460 98 EFF2 89.4 89.7 0.82 29.5 1LE1002-1DB4$
$-$
$$$$-Z 73
F90
1.5 1.75 100 L 940 15.3 74 72.6 0.77 3.8 1LE1002-1AC4$
$-$
$$$$-Z 19
F90
2.2 2.55 112 M 930 23 78 78.1 0.77 5.3 1LE1002-1BC2$
$-$
$$$$-Z 25
F90
3 3.45 132 S 955 30 80 79.4 0.74 7.3 1LE1002-1CC0$
$-$
$$$$-Z 34
F90
4 4.6 132 M 950 40 83 83.4 0.76 9.2 1LE1002-1CC2$
$-$
$$$$-Z 39
F90
5.5 6.3 132 M 950 55 85 85.3 0.75 12.4 1LE1002-1CC3$
$-$
$$$$-Z 48
F90
7.5 8.6 160 M 970 75 86 85.4 0.73 17.2 1LE1002-1DC2$
$-$
$$$$-Z 72
F90
11 12.6 160 L 965 110 87.6 87.9 0.77 23.5 1LE1002-1DC4$
$-$
$$$$-Z 92
F90
0.75 0.86 100 L 695 10.4 66 60.2 0.65 2.45 1LE1002-1AD4$
$-$
$$$$-Z 17
F90
1.1 1.3 100 L 695 15.1 70.2 67.6 0.65 3.5 1LE1002-1AD5$
$-$
$$$$-Z 22
F90
1.5 1.75 112 M 675 20 69.5 69.7 0.71 4.4 1LE1002-1BD2$
$-$
$$$$-Z 25
F90
2.2 2.55 132 S 720 30 78.8 76.4 0.65 6.2 1LE1002-1CD0$
$-$
$$$$-Z 37
F90
3 3.45 132 M 715 40 78.5 77.9 0.65 8.5 1LE1002-1CD2$
$-$
$$$$-Z 44
F90
4 4.6 160 M 720 53 80 78.7 0.69 10.4 1LE1002-1DD2$
$-$
$$$$-Z 60
F90
5.5 6.3 160 M 720 73 83.5 83.9 0.70 13.6 1LE1002-1DD3$
$-$
$$$$-Z 72
F90
7.5 8.6 160 L 715 100 83.5 84.7 0.70 18.6 1LE1002-1DD4$
$-$
$$$$-Z 91
F90

© Siemens AG 2007

New Generation 1LE1

Order No. with -Z
and order code
Locked-rotor
torque
Locked-rotor
current
Breakdown
torque
Torque class Moment
of inertia
pressure level
at 50 Hz

kgm2 dB(A) dB(A)
1LE1002-1AA4$
$-$
$$$$-Z 3.2 6.2 3.3 16 0.0034 72 84
F90
1LE1002-1BA2$
$-$
$$$$-Z 2.7 7.3 3.7 16 0.0067 69 81
F90
1LE1002-1CA0$
$-$
$$$$-Z 2 5.6 2.6 16 0.01267 68 80
F90
1LE1002-1CA1$
$-$
$$$$-Z 2.2 6.4 3 16 0.01601 68 80
F90
1LE1002-1DA2$
$-$
$$$$-Z 2.1 6.1 2.7 16 0.02971 70 82
F90
1LE1002-1DA3$
$-$
$$$$-Z 2.5 6.1 3.2 16 0.03619 70 82
F90
1LE1002-1DA4$
$-$
$$$$-Z 2.5 7 3.2 16 0.04395 70 82
F90
1LE1002-1AB4$
$-$
$$$$-Z 2.3 5.1 2.7 16 0.0059 63 75
F90
1LE1002-1AB5$
$-$
$$$$-Z 2.4 5.4 2.6 16 0.0078 63 75
F90
1LE1002-1BB2$
$-$
$$$$-Z 2.2 5.3 2.6 16 0.0102 58 70
F90
1LE1002-1CB0$
$-$
$$$$-Z 2.3 6.2 2.7 16 0.0186 64 76
F90
1LE1002-1CB2$
$-$
$$$$-Z 2.5 6.6 2.9 16 0.02371 64 76
F90
1LE1002-1DB2$
$-$
$$$$-Z 2.3 6.4 3.1 16 0.04395 64 76
F90
1LE1002-1DB4$
$-$
$$$$-Z 2.5 7 3.4 16 0.05616 64 76
F90
1LE1002-1AC4$
$-$
$$$$-Z 2.1 4.1 2.4 16 0.0065 61 73
F90
1LE1002-1BC2$
$-$
$$$$-Z 2.3 4.1 2.5 16 0.0092 68 80
F90
1LE1002-1CC0$
$-$
$$$$-Z 2 4.6 2.6 16 0.0167 63 75
F90
1LE1002-1CC2$
$-$
$$$$-Z 2.1 4.7 2.5 16 0.02116 63 75
F90
1LE1002-1CC3$
$-$
$$$$-Z 2.5 5.2 2.8 16 0.02734 63 75
F90
1LE1002-1DC2$
$-$
$$$$-Z 2.1 5.5 2.9 16 0.04993 68 80
F90
1LE1002-1DC4$
$-$
$$$$-Z 2.2 5.4 2.8 16 0.0678 68 80
F90
1LE1002-1AD4$
$-$
$$$$-Z 1.8 2.8 2 16 0.0056 66 78
F90
1LE1002-1AD5$
$-$
$$$$-Z 1.5 2.9 1.8 16 0.0078 66 78
F90
1LE1002-1BD2$
$-$
$$$$-Z 1.8 3 1.9 16 0.0094 66 78
F90
1LE1002-1CD0$
$-$
$$$$-Z 1.5 3.5 2.1 13 0.0186 53 65
F90
1LE1002-1CD2$
$-$
$$$$-Z 1.5 3.3 2 13 0.02372 53 65
F90
1LE1002-1DD2$
$-$
$$$$-Z 1.7 3.8 2.3 13 0.0439 68 80
F90
1LE1002-1DD3$
$-$
$$$$-Z 1.6 4 2.2 13 0.0562 68 80
F90
1LE1002-1DD4$
$-$
$$$$-Z 1.7 3.8 2.2 13 0.0772 68 80
F90

© Siemens AG 2007

New Generation 1LE1

50 Hz 50 Hz
460 VY 460 V∆ (210 … 230 V∆/ (360 … 400 V∆/ (395 … 435 VY) 1) (395 … 435 V∆) 1)
360 … 400 VY) 1) 625 … 695 VY) 1)
outputs at 60 Hz
22 34 27 40 21 33 23 35
1LE1002-1A..$
$-$
$…-Z 100 L " " " " ✓ ✓ ✓ ✓
F90
1LE1002-1B..$
$-$
$…-Z 112 M " " " " ✓ ✓ ✓ ✓
F90
1LE1002-1C..$
$-$
$…-Z 132 S/M " " " " ✓ ✓ ✓ ✓
F90
1LE1002-1D..$
$-$
$…-Z 160 M/L " " " " ✓ ✓ ✓ ✓
F90
Page 1/78).

IM B3 IM B6 IM B7 IM B8 IM V6 IM V5 Flange IM B5 IM V1 IM V3 IM B35
2) 3) 3) 3) 3) 3) 3) 4)
without size without 3)
protec- protec-
tive tive
cover 3) cover 3)
A T U V D C F G H J
Order No. – – – – – – – – – –
supplement -Z
with order
code
1LE1002-1A...-.$
$..-Z 100 L # # # # # # FF 215 ✓ ✓ ✓ ✓
F90
1LE1002-1B...-.$
$..-Z 112 M # # # # # # FF 215 ✓ ✓ ✓ ✓
F90
1LE1002-1C...-.$
$..-Z 132 S/M # # # # # # FF 265 ✓ ✓ ✓ ✓
F90
1LE1002-1D...-.$
$..-Z 160 M/L # # # # # # FF 300 ✓ ✓ ✓ ✓
F90

Flange size IM B14 IM V19 IM V18 IM B34
3) 5) 3)
without protective cover 3)
K L M N
Order No. – – – –
supplement -Z
with order
code
1LE1002-1A...-.$
$..-Z 100 L FT 130 ✓ ✓ ✓ ✓
F90
1LE1002-1B...-.$
$..-Z 112 M FT 130 ✓ ✓ ✓ ✓
F90
1LE1002-1C...-.$
$..-Z 132 S/M FT 165 ✓ ✓ ✓ ✓
F90
1LE1002-1D...-.$
$..-Z 160 M/L FT 215 ✓ ✓ ✓ ✓
F90
# Standard version ✓ With additional charge
1) A rated voltage range is also specified on the rating plate. 4) The types of construction IM V3 and IM V1 without protective cover are
2)
The types of construction IM B6/7/8, IM V6 and IM V5 without protective also possible as long as no condensation drainage holes (order code
cover are also possible as long as no condensation drainage holes (order H03) and no stamping of these types of construction on the rating plate
code H03) and no stamping of these types of construction on the rating are required. As standard, the type of construction IM B5 is then stamped
plate are required. As standard, the type of construction IM B3 is then on the rating plate.
5)
stamped on the rating plate. The types of construction IM V19 and IM V18 without protective cover are
3)
The type of construction is stamped on the rating plate. When ordering also possible as long as no condensation drainage holes (order code
with condensation drainage holes (order code H03), it is absolutely neces- H03) and no stamping of these types of construction on the rating plate
sary to specify the type of construction for the exact position of the con- are required. As standard, the type of construction IM B14 is then stamped
densation drainage holes during manufacture. on the rating plate.

© Siemens AG 2007

New Generation 1LE1

Motor type Frame
size
Without Motor protec- Motor protec- Motor tempera- NTC thermistors Temperature
1
motor tion with PTC tion with PTC ture detection for tripping detectors for
protection thermistors with thermistors with with embedded tripping 1)
1)
tripping
A B C F Z Z
Order code Q2A Q3A
1LE1002-1A...-..$
$.-Z 100 L # ✓ ✓ ✓ ✓ ✓
F90
1LE1002-1B...-..$
$.-Z 112 M # ✓ ✓ ✓ ✓ ✓
F90
1LE1002-1C...-..$
$.-Z 132 S/M # ✓ ✓ ✓ ✓ ✓
F90
1LE1002-1D...-..$
$.-Z 160 M/L # ✓ ✓ ✓ ✓ ✓
F90
# Standard version
4 5 6 7
1LE1002-1A...-...$
$-Z 100 L # ✓ ✓ ✓
F90
1LE1002-1B...-...$
$-Z 112 M # ✓ ✓ ✓
F90
1LE1002-1C...-...$
$-Z 132 S/M # ✓ ✓ ✓
F90
1LE1002-1D...-...$
$-Z 160 M/L # ✓ ✓ ✓
F90
# Standard version
1)
For appropriate tripping unit, see Catalog LV 1.
2)
With type of construction, cast feet as standard. Screwed-on feet are
3)

© Siemens AG 2007

New Generation 1LE1
fan cover with high efficiency

size
Operating values at rated output Order No. with -Z
and order code
Price Weight
speed at torque at Class at at factor at current at for voltage, type of construc- type of type of
50 Hz 50 Hz accord- 50 Hz 50 Hz 50 Hz 400 V. tion, motor protection and construc- construc-
ing 4/4-load 3/4-load 4/4-load 50 Hz connection box, see table tion tion
to CEMEP from Page 1/76. approx.
3 3.45 100 L 2905 9.9 EFF1 86.7 87.5 0.84 5.9 1LE1001-1AA4$
$-$
$$$$-Z 21
F90
4 4.6 112 M 2950 13 EFF1 88 88.5 0.86 7.4 1LE1001-1BA2$
$-$
$$$$-Z 27
F90
5.5 6.3 132 S 2950 18 EFF1 89.5 90.6 0.87 10.2 1LE1001-1CA0$
$-$
$$$$-Z 39
F90
7.5 8.6 132 S 2950 24 EFF1 90 91 0.87 13.8 1LE1001-1CA1$
$-$
$$$$-Z 43
F90
11 12.6 160 M 2955 36 EFF1 90.8 91 0.87 20 1LE1001-1DA2$
$-$
$$$$-Z 67
F90
15 17.3 160 M 2955 48 EFF1 91.4 91.5 0.88 27 1LE1001-1DA3$
$-$
$$$$-Z 75
F90
18.5 21.3 160 L 2955 60 EFF1 92 92.5 0.88 33 1LE1001-1DA4$
$-$
$$$$-Z 84
F90
2.2 2.55 100 L 1455 14 EFF1 86.4 87 0.81 4.55 $-$
1LE1001-1AB4$ $$$$-Z 21
F90
3 3.45 100 L 1455 20 EFF1 87.4 88 0.82 6 1LE1001-1AB5$
$-$
$$$$-Z 25
F90
4 4.6 112 M 1460 26 EFF1 88.3 88.5 0.81 8.1 1LE1001-1BB2$
$-$
$$$$-Z 29
F90
5.5 6.3 132 S 1465 36 EFF1 89.2 89.5 0.80 11.2 1LE1001-1CB0$
$-$
$$$$-Z 42
F90
7.5 8.6 132 M 1465 49 EFF1 90.1 91 0.83 14.4 1LE1001-1CB2$
$-$
$$$$-Z 49
F90
11 12.6 160 M 1470 71 EFF1 91.2 91.8 0.85 20.5 1LE1001-1DB2$
$-$
$$$$-Z 71
F90
15 17.3 160 L 1475 97 EFF1 92 92.4 0.85 27.5 1LE1001-1DB4$
$-$
$$$$-Z 83
F90
1.5 1.75 100 L 970 15 84.5 84.6 0.73 3.5 1LE1001-1AC4$
$-$
$$$$-Z 25
F90
2.2 2.55 112 M 965 22 85 86.5 0.75 5 1LE1001-1BC2$
$-$
$$$$-Z 29
F90
3 3.45 132 S 970 30 86 85.6 0.74 6.9 1LE1001-1CC0$
$-$
$$$$-Z 38
F90
4 4.6 132 M 970 39 86 86.5 0.78 8.6 1LE1001-1CC2$
$-$
$$$$-Z 43
F90
5.5 6.3 132 M 970 54 88 89 0.77 11.8 1LE1001-1CC3$
$-$
$$$$-Z 52
F90
7.5 8.6 160 M 975 73 89 89.6 0.77 15.8 1LE1001-1DC2$
$-$
$$$$-Z 77
F90
11 12.6 160 L 975 108 89.5 90.5 0.80 22 1LE1001-1DC4$
$-$
$$$$-Z 93
F90
0.75 0.86 100 L 725 9.9 67 65 0.57 2.85 1LE1001-1AD4$
$-$
$$$$-Z 21
F90
1.1 1.3 110 L 725 14 67 64.5 0.57 4.15 1LE1001-1AD5$
$-$
$$$$-Z 25
F90
1.5 1.75 112 M 715 20 75 75.5 0.65 4.45 1LE1001-1BD2$
$-$
$$$$-Z 29
F90
2.2 2.55 132 S 725 29 77.5 76.7 0.63 6.5 1LE1001-1CD0$
$-$
$$$$-Z 41
F90
3 3.45 132 M 720 40 81 82 0.64 8.4 1LE1001-1CD2$
$-$
$$$$-Z 49
F90
4 4.6 160 M 730 52 87 88 0.69 9.6 1LE1001-1DD2$
$-$
$$$$-Z 69
F90
5.5 6.3 160 M 735 72 87.5 89 0.69 13.2 1LE1001-1DD3$
$-$
$$$$-Z 82
F90
7.5 8.6 160 L 730 98 88 89 0.72 17 1LE1001-1DD4$
$-$
$$$$-Z 94
F90

© Siemens AG 2007

New Generation 1LE1

Order No. with -Z
and order code
Locked-rotor
torque
Locked-rotor
current
Breakdown
torque
Torque class Moment
of inertia
pressure level
at 50 Hz

kgm2 dB(A) dB(A)
1LE1001-1AA4$
$-$
$$$$-Z 2.3 7 3.3 16 0.0044 72 84
F90
1LE1001-1BA2$
$-$
$$$$-Z 2.4 7.4 3.3 16 0.0092 69 81
F90
1LE1001-1CA0$
$-$
$$$$-Z 1.8 6.7 2.9 16 0.02012 68 80
F90
1LE1001-1CA1$
$-$
$$$$-Z 2.2 7.5 3.1 16 0.02353 68 80
F90
1LE1001-1DA2$
$-$
$$$$-Z 2.1 7.4 3.2 16 0.04471 70 82
F90
1LE1001-1DA3$
$-$
$$$$-Z 2.4 7.6 3.4 16 0.05277 70 82
F90
1LE1001-1DA4$
$-$
$$$$-Z 2.9 7.9 3.6 16 0.06085 70 82
F90
1LE1001-1AB4$
$-$
$$$$-Z 2.1 6.9 3.3 16 0.0086 63 75
F90
1LE1001-1AB5$
$-$
$$$$-Z 2 6.9 3.1 16 0.0109 63 75
F90
1LE1001-1BB2$
$-$
$$$$-Z 2.5 7.1 3.2 16 0.014 58 70
F90
1LE1001-1CB0$
$-$
$$$$-Z 2.3 6.9 2.9 16 0.02698 64 76
F90
1LE1001-1CB2$
$-$
$$$$-Z 2.3 6.9 2.9 16 0.03353 64 76
F90
1LE1001-1DB2$
$-$
$$$$-Z 2.2 6.7 2.8 16 0.06495 64 76
F90
1LE1001-1DB4$
$-$
$$$$-Z 2.5 7.3 3 16 0.08281 64 76
F90
1LE1001-1AC4$
$-$
$$$$-Z 2 6.2 2.9 16 0.0113 61 73
F90
1LE1001-1BC2$
$-$
$$$$-Z 2.1 6 3.1 16 0.0139 68 80
F90
1LE1001-1CC0$
$-$
$$$$-Z 1.6 5.6 2.6 13 0.02371 63 75
F90
1LE1001-1CC2$
$-$
$$$$-Z 1.6 5.6 2.5 13 0.02918 63 75
F90
1LE1001-1CC3$
$-$
$$$$-Z 1.9 6.1 2.8 16 0.03673 63 75
F90
1LE1001-1DC2$
$-$
$$$$-Z 1.8 6.3 2.8 16 0.0754 68 80
F90
1LE1001-1DC4$
$-$
$$$$-Z 1.7 6.2 2.7 16 0.0975 68 80
F90
1LE1001-1AD4$
$-$
$$$$-Z 1.5 3.8 2.6 13 0.0086 66 78
F90
1LE1001-1AD5$
$-$
$$$$-Z 1.7 3.8 2.9 13 0.0109 66 78
F90
1LE1001-1BD2$
$-$
$$$$-Z 1.4 3.6 2 13 0.014 66 78
F90
1LE1001-1CD0$
$-$
$$$$-Z 1.4 3.6 1.8 10 0.02698 53 65
F90
1LE1001-1CD2$
$-$
$$$$-Z 1.6 3.9 2.1 10 0.03463 53 65
F90
1LE1001-1DD2$
$-$
$$$$-Z 1.8 4.3 2 13 0.0649 68 80
F90
1LE1001-1DD3$
$-$
$$$$-Z 2.1 4.4 2.1 13 0.0828 68 80
F90
1LE1001-1DD4$
$-$
$$$$-Z 1.9 4.5 2.1 13 0.0982 68 80
F90

© Siemens AG 2007

New Generation 1LE1

50 Hz 50 Hz
460 VY 460 V∆ (210 … 230 V∆/ (360 … 400 V∆/ (395 … 435 VY) 1) (395 … 435 V∆) 1)
360 … 400 VY) 1) 625 … 695 VY) 1)
outputs at 60 Hz
22 34 27 40 21 33 23 35
1LE1001-1A..$
$-$
$…-Z 100 L " " " " ✓ ✓ ✓ ✓
F90
1LE1001-1B..$
$-$
$…-Z 112 M " " " " ✓ ✓ ✓ ✓
F90
1LE1001-1C..$
$-$
$…-Z 132 S/M " " " " ✓ ✓ ✓ ✓
F90
1LE1001-1D..$
$-$
$…-Z 160 M/L " " " " ✓ ✓ ✓ ✓
F90
Page 1/78).

IM B3 IM B6 IM B7 IM B8 IM V6 IM V5 Flange IM B5 IM V1 IM V3 IM B35
2) 3) 3) 3) 3) 3) 3) 4)
without size without 3)
protec- protec-
tive tive
cover 3) cover 3)
A T U V D C F G H J
Order No. – – – – – – – – – –
supplement -Z
with order
code
1LE1001-1A...-.$
$..-Z 100 L # # # # # # FF 215 ✓ ✓ ✓ ✓
F90
1LE1001-1B...-.$
$..-Z 112 M # # # # # # FF 215 ✓ ✓ ✓ ✓
F90
1LE1001-1C...-.$
$..-Z 132 S/M # # # # # # FF 265 ✓ ✓ ✓ ✓
F90
1LE1001-1D...-.$
$..-Z 160 M/L # # # # # # FF 300 ✓ ✓ ✓ ✓
F90

Flange size IM B14 IM V19 IM V18 IM B34
3) 5) 3)
without protective cover 3)
K L M N
Order No. – – – –
supplement -Z
with order
code
1LE1001-1A...-.$
$..-Z 100 L FT 130 ✓ ✓ ✓ ✓
F90
1LE1001-1B...-.$
$..-Z 112 M FT 130 ✓ ✓ ✓ ✓
F90
1LE1001-1C...-.$
$..-Z 132 S/M FT 165 ✓ ✓ ✓ ✓
F90
1LE1001-1D...-.$
$..-Z 160 M/L FT 215 ✓ ✓ ✓ ✓
F90
# Standard version ✓ With extra price
1) A rated voltage range is also specified on the rating plate. 4) The types of construction IM V3 and IM V1 without protective cover are
2)
The types of construction IM B6/7/8, IM V6 and IM V5 without protective also possible as long as no condensation drainage holes (order code
cover are also possible as long as no condensation drainage holes (order H03) and no stamping of these types of construction on the rating plate
code H03) and no stamping of these types of construction on the rating are required. As standard, the type of construction IM B5 is then stamped
plate are required. As standard, the type of construction IM B3 is then on the rating plate.
5)
stamped on the rating plate. The types of construction IM V19 and IM V18 without protective cover are
3)
The type of construction is stamped on the rating plate. When ordering also possible as long as no condensation drainage holes (order code
with condensation drainage holes (order code H03), it is absolutely neces- H03) and no stamping of these types of construction on the rating plate
sary to specify the type of construction for the exact position of the con- are required. As standard, the type of construction IM B14 is then stamped
densation drainage holes during manufacture. on the rating plate.

© Siemens AG 2007

New Generation 1LE1

Motor type Frame
size
Without Motor protec- Motor protec- Motor tempera- NTC ther- Temperature
1
motor tion with PTC tion with PTC ture detection mistors for trip- detectors for
protection thermistors with thermistors with with embedded ping tripping 1)
1)
tripping
A B C F Z Z
Order code Q2A Q3A
1LE1001-1A...-..$
$.-Z 100 L # ✓ ✓ ✓ ✓ ✓
F90
1LE1001-1B...-..$
$.-Z 112 M # ✓ ✓ ✓ ✓ ✓
F90
1LE1001-1C...-..$
$.-Z 132 S/M # ✓ ✓ ✓ ✓ ✓
F90
1LE1001-1D...-..$
$.-Z 160 M/L # ✓ ✓ ✓ ✓ ✓
F90
# Standard version
4 5 6 7
1LE1001-1A ...-...$
$-Z 100 L # ✓ ✓ ✓
F90
1LE1001-1B ...-...$
$-Z 112 M # ✓ ✓ ✓
F90
1LE1001-1C ...-...$
$-Z 132 S/M # ✓ ✓ ✓
F90
1LE1001-1D ...-...$
$-Z 160 M/L # ✓ ✓ ✓
F90
# Standard version
1)
For appropriate tripping unit, see Catalog LV 1.
2)
With type of construction, cast feet as standard. Screwed-on feet are
3)

© Siemens AG 2007

New Generation 1LE1
Special versions

1 Voltages
Additional order codes for other voltages or voltage codes For some non-standard voltages at 50 or 60 Hz, order codes are
(without -Z supplement) specified. They are ordered by specifying the code digit 9 for
voltage in the 12th position and 0 in the 13th position of the Order
Not possible for General Line motors with shorter delivery time. No. and the appropriate order code.
Special versions Voltage code Additional identi- Motor type frame size
12th / 13th position of the fication code
Order No. with order code
and plain text if
required
56 63 71 80 90 100 112 132 160
Self-ventilated energy-saving motors with improved efficiency
Self-ventilated energy-saving motors with high efficiency
Self-ventilated motors with increased output and improved efficiency
Self-ventilated motors with increased output and high efficiency
Forced-air cooled motors without external fan and fan cover with improved efficiency
Forced-air cooled motors without external fan and fan cover with high efficiency
1LE1 (Aluminum)
Voltage at 60 Hz
220 V∆/380 VY; 50 Hz output 9 0 M2A ✓ ✓ ✓ ✓
220 V∆/380 VY; 60 Hz output 9 0 M1A ✓ ✓ ✓ ✓
380 V∆/660 VY; 50 Hz output 9 0 M2B ✓ ✓ ✓ ✓
380 V∆/660 VY; 60 Hz output 9 0 M1B ✓ ✓ ✓ ✓
440 VY; 50 Hz output 9 0 M2C ✓ ✓ ✓ ✓
440 VY; 60 Hz output 9 0 M1C ✓ ✓ ✓ ✓
440 V∆; 50 Hz output 9 0 M2D ✓ ✓ ✓ ✓
440 V∆; 60 Hz output 9 0 M1D ✓ ✓ ✓ ✓
460 VY; 50 Hz output 9 0 M2E ✓ ✓ ✓ ✓
460 VY; 60 Hz output 9 0 M1E " " " "
460 V∆; 50 Hz output 9 0 M2F ✓ ✓ ✓ ✓
460 V∆; 60 Hz output 9 0 M1F " " " "
575 VY; 50 Hz output 9 0 M2G ✓ ✓ ✓ ✓
575 VY; 60 Hz output 9 0 M1G ✓ ✓ ✓ ✓
575 V∆; 50 Hz output 9 0 M2H ✓ ✓ ✓ ✓
575 V∆; 60 Hz output 9 0 M1H ✓ ✓ ✓ ✓
Non-standard voltages and / or frequencies
Non-standard winding for volt- 9 0 M1Y ✓ ✓ ✓ ✓
ages between 200 V and 690 V
(voltages outside this range are
available on request) 1)
1) Plain text must be specified in the order: voltage, frequency, circuit,

required rated output in kW.

© Siemens AG 2007

New Generation 1LE1
Special versions
Options
Options or order codes (supplement -Z is required)
Not possible for General Line motors with shorter delivery time.
1
Special versions Additional identi- Motor type frame size
fication code -Z
with order code
and plain text if
required
56 63 71 80 90 100 112 132 160
1LE1 (Aluminum)
Motor connection and connection boxes
One cable entry, metal R15 ✓ ✓ ✓ ✓
Rotation of the connection box R10 " " " "
through 90°, entry from DE
through 90°, entry from NDE
through 180°
External earthing H04 ✓ ✓ ✓ ✓
Windings and insulation
Temperature class 155 (F), N01 ✓ ✓ ✓ ✓
used acc. to 155 (F),
with service factor (SF)
with increased output
used acc. to 155 (F), with
increased coolant temperature
used acc. to 130 (B),
coolant temperature 45 °C,
derating approx. 4%
derating approx. 8%
derating approx. 13%
Temperature class 155 (F), Y52 • and ✓ ✓ ✓ ✓
used acc. to 155 (F), other identification
requirements code
Special finish in RAL 7030 # # # #
stone gray
Special finish in other standard Y54 • and ✓ ✓ ✓ ✓
RAL colors : RAL 1002, 1013, special finish
1015, 1019, 2003, 2004, 3000, RAL….
3007, 5007, 5009, 5010, 5012,
5015, 5017, 5018, 5019, 6011,
6019, 6021, 7000, 7001, 7004,
7011, 7016, 7022, 7031, 7032,
7033, 7035, 9001, 9002, 9005
Special finish in special RAL Y51 • and ✓ ✓ ✓ ✓
colors: for RAL colors, see special finish
“Special finish in special RAL RAL….
colors“, Page 1/6
Unpainted S00 " " " "
(only cast iron parts primed)
Unpainted, only primed S01 ✓ ✓ ✓ ✓
For legend, see Page 1/81. For footnotes, see Page 1/82.

© Siemens AG 2007

New Generation 1LE1
Special versions
1
fication code -Z
with order code
and plain text if
required
56 63 71 80 90 100 112 132 160
1LE1 (Aluminum)
Modular technology – basic versions 1)
Mounting of separately driven F70 ✓ ✓ ✓ ✓
fan
Mounting of brake 2) F01 ✓ ✓ ✓ ✓
Mounting of 1XP8012-10 (HTL) G01 ✓ ✓ ✓ ✓
rotary pulse encoder 3)
Mounting of 1XP8012-20 (TTL) G02 ✓ ✓ ✓ ✓
Modular technology – additional versions
Brake supply voltage 24 V DC F10 ✓ ✓ ✓ ✓
Brake supply voltage 230 V AC, F11 " " " "
50/60 Hz
Brake supply voltage 400 V AC, F12 ✓ ✓ ✓ ✓
50/60 Hz
Mechanical manual brake F50 ✓ ✓ ✓ ✓
release with lever (no locking)
1)
Special technology
Mounting of LL 861 900 220 G04 ✓ ✓ ✓ ✓
Mounting of HOG 9 D 1024 I G05 ✓ ✓ ✓ ✓
Mounting of HOG 10 D 1024 I G06 ✓ ✓ ✓ ✓
Mechanical design and degrees of protection
Protective cover, as well as H00 ✓ ✓ ✓ ✓
mechanical protection for the
encoder 3)
Screwed-on feet H01 ✓ ✓ ✓ ✓
(instead of cast)
4)
Condensation drainage holes H03 ✓ ✓ ✓ ✓
Prepared for mountings, only G40 ✓ ✓ ✓ ✓
centre hole
Prepared for mountings with G41 ✓ ✓ ✓ ✓
D12 shaft
Prepared for mountings with G42 ✓ ✓ ✓ ✓
D16 shaft
Bearings and lubrication
Measuring nipple for SPM Q01 ✓ ✓ ✓ ✓
shock pulse measurement for
bearing inspection 5)
Bearing design for increased L22 ✓ ✓ ✓ ✓
cantilever forces
Special bearing for DE and L25 ✓ ✓ ✓ ✓
NDE, bearing size 63
5)
Regreasing device L23 ✓ ✓ ✓ ✓
Located bearing at DE L20 ✓ ✓ ✓ ✓
Located bearing at NDE L21 ✓ ✓ ✓ #
Balance and vibration quantity
Half-key balancing (standard) # # # #
Full-key balancing L02 ✓ ✓ ✓ ✓
Balancing without fitted key L01 ✓ ✓ ✓ ✓
Vibration quantity level A # # # #
Vibration quantity level B L00 ✓ ✓ ✓ ✓
For legend, see Page 1/81. For footnotes, see Page 1/82.

© Siemens AG 2007

New Generation 1LE1
Special versions
1
fication code -Z
with order code
and plain text if
required
56 63 71 80 90 100 112 132 160
1LE1 (Aluminum)
Shaft and rotor
Concentricity of shaft exten- L08 ✓ ✓ ✓ ✓
sion, coaxiality and linear
movement in accordance with
DIN 42955 Tolerance R for
flange-mounting motors
Second standard shaft exten- L05 ✓ ✓ ✓ ✓
sion
sion in accordance with
DIN 42955 Tolerance R
Standard shaft made of non- L06 ✓ ✓ ✓ ✓
rusting steel
Heating and ventilation
Anti-condensation heaters for Q02 ✓ ✓ ✓ ✓
230 V
115 V
Sheet metal fan cover F74 ✓ ✓ ✓ ✓
Rating plate and extra rating plate
Second rating plate, loose M10 ✓ ✓ ✓ ✓
Nirosta rating plate M11 ✓ ✓ ✓ ✓
Extra rating plate or rating plate Y80 • and identi- ✓ ✓ ✓ ✓
with deviating rating plate data fication code
Extra rating plate with identifi- Y82 • and identi- ✓ ✓ ✓ ✓
cation codes fication code
Additional information on rating Y84 • and identi- ✓ ✓ ✓ ✓
plate and on package label fication code
(max. of 20 characters)
Packaging, safety notes, documentation and test certificates
Without safety and commission- B00 " " " "
ing note.
Customer's declaration of
renouncement required.
With one safety and start-up B01 " " " "
guide per box pallet
Acceptance test certificate 3.1 B02 ✓ ✓ ✓ ✓
in accordance with EN 10204
Operating instructions on CD B03 ✓ ✓ ✓ ✓
enclosed
Printed operating instructions B04 ✓ ✓ ✓ ✓
English/German enclosed
Wire-lattice pallet B99 " " " "
Connected in star for dispatch M01 ✓ ✓ ✓ ✓
Connected in delta for dispatch M02 ✓ ✓ ✓ ✓
# Standard version
• This order code only determines the price of the version –
Additional plain text is required.
For footnotes, see Page 1/82.

© Siemens AG 2007

New Generation 1LE1
Special versions
1) A second shaft extension is not possible. Please inquire for mounted 4) Supplied with the condensation drainage holes sealed at the drive end
brakes. (DE) and non-drive end (NDE) (IP55, IP56, IP65). If condensation draining
2) When quoting or ordering, it is necessary to provide the brake supply volt- holes are required for motors with IM B6, IM B7 or IM B8 type of construc-
age for order codes F10, F11 and F12. tion (feet located on side or top), it is necessary to order the motors in their
3)
respective type of construction and order code H03, so that the conden-
All encoders are supplied with a protective cover as standard. The protec- sation drainage holes can be mounted in the correct positional arrange-
tive cover is not supplied with the combination rotary pulse encoder with ment.
separately driven fan, as, in this case, the roatry pulse encoder is installed 5)
under the fan cover. Not possible when brake is mounted.

© Siemens AG 2007

New Generation 1LE1
Special versions
Options or order codes (supplement -Z is required)
Not possible for General Line motors with shorter delivery time.
1
fication code -Z
with order code
and plain text if
required
56 63 71 80 90 100 112 132 160
1LE1 (Aluminum)
Motor connection and connection boxes
One cable entry, metal R15 ✓ ✓ ✓ ✓
through 90°, entry from DE
through 90°, entry from NDE
through 180°
External earthing H04 ✓ ✓ ✓ ✓
Windings and insulation
with service factor (SF)
with increased output
used acc. to 155 (F), with
increased coolant temperature
derating approx. 4%
derating approx. 8%
Temperature class 155 (F), Y52 • and identi- ✓ ✓ ✓ ✓
used acc. to 155 (F), fication code
other requirements
Special finish in RAL 7030 # # # #
stone gray
Special finish in other standard Y54 • and " ✓ ✓ ✓
RAL colors : RAL 1002, 1013, special finish
1015, 1019, 2003, 2004, 3000, RAL….
3007, 5007, 5009, 5010, 5012,
5015, 5017, 5018, 5019, 6011,
6019, 6021, 7000, 7001, 7004,
7011, 7016, 7022, 7031, 7032,
7033, 7035, 9001, 9002, 9005
Special finish in special-RAL Y51 • and ✓ ✓ ✓ ✓
colors: for RAL colors, see special finish
“Special finish in special RAL RAL….
colors“, Page 1/6
Unpainted S00 " " " "
(only cast iron parts primed)
Unpainted, only primed S01 ✓ ✓ ✓ ✓
For legend and footnotes, see Page 1/85.

© Siemens AG 2007

New Generation 1LE1
Special versions
1
fication code -Z
with order code
and plain text if
required
56 63 71 80 90 100 112 132 160
1LE1 (Aluminum)
Mechanical design and degree of protection
Screwed-on feet H01 ✓ ✓ ✓ ✓
(instead of cast)
1) H03
Condensation drainage holes ✓ ✓ ✓ ✓
Bearings and lubrication
Measuring nipple for SPM Q01 ✓ ✓ ✓ ✓
shock pulse measurement for
bearing inspection
Bearing design for increased L22 ✓ ✓ ✓ ✓
canteliver forces
Special bearing for DE and L25 ✓ ✓ ✓ ✓
NDE, bearing size 63
Regreasing device L23 ✓ ✓ ✓ ✓
Located bearing at DE L20 ✓ ✓ ✓ ✓
Located bearing at NDE L21 ✓ ✓ ✓ #
Balance and vibration quantity
Half-key balancing (standard) # # # #
Full-key balancing L02 ✓ ✓ ✓ ✓
Balancing without fitted key L01 ✓ ✓ ✓ ✓
Vibration quantity level A # # # #
Vibration quantity level B L00 ✓ ✓ ✓ ✓
Shaft and rotor
sion, coaxiality and linear
movement in accordance with
DIN 42955 Tolerance R for
flange-mounting motors
sion in accordance with
DIN 42955 Tolerance R
Standard shaft made of non- L06 ✓ ✓ ✓ ✓
rusting steel
Heating and ventillation
230 V
115 V
Sheet metal fan cover F74 ✓ ✓ ✓ ✓
Rating plate and extra rating plate
Second rating plate, loose M10 ✓ ✓ ✓ ✓
Nirosta rating plate M11 ✓ ✓ ✓ ✓
Extra rating plate or rating plate Y80 • and identi- ✓ ✓ ✓ ✓
with deviating rating plate data fication code
Extra rating plate with identifi- Y82 • and identi- ✓ ✓ ✓ ✓
cation codes fication code
Additional information on rating Y84 • and identi- ✓ ✓ ✓ ✓
plate and on package label fication code
(max. of 20 characters)
For legend and footnotes, see Page 1/85.

© Siemens AG 2007

New Generation 1LE1
Special versions
1
fication code -Z
with order code
and plain text if
required
56 63 71 80 90 100 112 132 160
1LE1 (Aluminum)
Packaging, safety notes, documentation and test certificates
Without safety and commission- B00 " " " "
ing note.
Customer's declaration of
renouncement required.
With one safety and start-up B01 " " " "
guide per box pallet
Acceptance test certificate 3.1 B02 ✓ ✓ ✓ ✓
in accordance with EN 10204
Operating instructions on CD B03 ✓ ✓ ✓ ✓
enclosed
Printed operating instructions B04 ✓ ✓ ✓ ✓
English/German enclosed
Wire-lattice pallet B99 " " " "
Connected in star for dispatch M01 ✓ ✓ ✓ ✓
Connected in delta for dispatch M02 ✓ ✓ ✓ ✓
# Standard version
• This order code only determines the price of the version –
Additional plain text is required.
1)
Supplied with the condensation drainage holes sealed at the drive end
(DE) and non-drive end (NDE) (IP55, IP56, IP65). If condensation draining
holes are required for motors with IM B6, IM B7 or IM B8 type of construc-
tion (feet located on side or top), it is necessary to order the motors in their
respective type of construction and order code H03, so that the conden-
sation drainage holes can be mounted in the correct positional arrange-
ment.

© Siemens AG 2007

New Generation 1LE1
Accessories and spare parts
■ Overview
1 Couplings Mounting of encoder
The motor from Siemens is connected to the machine or gear In the case of mounting by the customer.
unit through a coupling. Flender is an important coupling manu-
facturer with a wide range of products. For standard applica- Baumer Hübner GmbH
tions, Siemens recommends that elastic couplings of Flender 10967 Berlin
types N-Eupex and Rupex or torsionally rigid couplings of types Planufer 92b
Arpex and Zapex are used. For special applications, Fludex and Tel. +49 (0) 30-690 03-0
Elpex couplings are recommended. Fax +49 (0) 30-690 03-104
Available from: http://www.baumerhuebner.com

A. Friedr. Flender AG e-mail: [email protected]
Kupplungswerk Mussum
Industriepark Bocholt Leine & Linde (Deutschland) GmbH
Schlavenhorst 100 73430 Aalen
46395 Bocholt Bahnhofstraße 36
Tel. +49 (0) 2871-92 2185 Tel. +49 (0) 7361-78 093-0
Fax +49 (0) 2871-92 2579 Fax +49 (0) 7361-78 093-11
http://www.flender.com http://www.leinelinde.com
e-mail: [email protected] e-mail: [email protected]
Spare motors and repair parts You will find telephone numbers for other countries on our
• Supply commitment for spare motors and repair parts follow- Internet site:
ing delivery of the motor http://www.siemens.com/automation/service&support
- For up to 5 years, in the event of total motor failure, Siemens
will supply a comparable motor with regard to the mounting
dimensions and functions (the type series may vary).
- Repair parts will be supplied for up to 5 years.
- For up to 10 years, Siemens will provide information and will,
if necessary, supply documentation for repair parts.
• When repair parts are ordered, the following details must be
provided:
- Designation and part number
- Order No. and factory number of the motor
• For bearing types, see the „Orientation”, “Technical data”,
Page 1/23.
• For standard components, a supply commitment does not ap-
ply.
• Support – Hotline
In Germany
Tel.: 01 80 - 5 05 04 48

© Siemens AG 2007

New Generation 1LE1
Dimensions
■ Overview
Overall dimensions 1
L
G_D081_XX_00033
O
AD
H
AB
Frame Type Num- Dimensions Frame Type Num- Dimensions

size ber of size ber of
1LE1 poles L AD H AB O 1LE1 poles L AD H AB O
100 L General Line 395.5 166 100 196 2 x M32 x 1.5 132 S/ General Line 465 1) 202 132 256 2 x M32 x 1.5
1) 132 M motors with
motors with
shorter delivery shorter delivery
time time
Self-ventilated 395.5 166 100 196 2 x M32 x 1.5 Self-ventilated 465 1) 202 132 256 2 x M32 x 1.5
1)
energy-saving energy-saving
motors with motors with
improved/high improved/high
efficiency efficiency
Self-ventilated 430.5 166 100 196 2 x M32 x 1.5 Self-ventilated 515 1) 202 132 256 2 x M32 x 1.5
motors with 1) motors with
increased increased
output and output and
Forced-air- 321.5 166 100 196 2 x M32 x 1.5 Forced-air- 380.5 202 132 256 2 x M32 x 1.5
cooled motors cooled motors
without external without external
fan and fan fan and fan
cover with cover with
112 M General Line 389 1) 177 112 226 2 x M32 x 1.5 160 M/ General Line 604 1) 236.5 160 300 2 x M40 x 1.5
motors with 160 L motors with
shorter delivery shorter delivery
time time
Self-ventilated 389 1) 177 112 226 2 x M32 x 1.5 Self-ventilated 604 1) 236.5 160 300 2 x M40 x 1.5
energy-saving energy-saving
Self-ventilated 414 1) 177 112 226 2 x M32 x 1.5 Self-ventilated 664 1) 236.5 160 300 2 x M40 x 1.5
increased increased
output and output and
Forced-air- 311 177 112 226 2 x M32 x 1.5 Forced-air- 510 236.5 160 300 2 x M40 x 1.5
cooled motors cooled motors
without external without external
fan and fan fan and fan
cover with cover with
1) The length is specified as far as the tip of the fan cover.

© Siemens AG 2007

New Generation 1LE1
Dimensions
■ Overview (continued)
1 Notes on the dimensions 7 Dimension tolerances
For the following dimensions, the admissible deviations are
7 Dimension drawings according to DIN EN 50347 and
IEC 60072. given below:
7 Fits Dimension Dimensions Admissible
The shaft extensions specified in the dimension tables (DIN 748) designation deviation
and centering spigot diameters (DIN EN 50347) are machined H up to 250 –0.5
with the following fits: over 250 –1.0
Dimension ISO fit DIN ISO 286-2 E, EA –0.5
designation
D, DA up to 30 j6 Keyways and feather keyways (dimensions GA, GC, F and FA)
over 30 to 50 k6 are made in compliance with DIN 6885 Part 1.
over 50 m6 7 All dimensions are specified in mm.
N up to 250 j6
over 250 h6
F, FA h9
K H17
S Flange (FF) H17
The drilled holes of couplings and belt pulleys should have an
ISO fit of at least H7.

© Siemens AG 2007

New Generation 1LE1
Dimensions
SD configurator It is also easy to assign a suitable converter to the selected
motor.
1
SD configurator (on CD2 “Configuration” of catalog “CA01 –
The Siemens A&D Offline Mall”) The extensive help function not only explains the program func-
tions, it also contains extensive technical background material.
SD configurator product range:
Low-voltage motors
(energy-saving motors) with corresponding documentation
and dimension drawings, low-voltage inverters of the
MICROMASTER 4 product series, SINAMICS G110 and
SINAMICS G120 inverter chassis units as well as
SINAMICS G120D distributed frequency inverters, and
SIMATIC 200S FC frequency converters for distributed I/O.
The interactive CA 01 catalog can be ordered from your local
Siemens sales representative or on the Internet at
http://www.siemens.com/automation/CA01
The interactive catalog CA 01 – the offline mall of Siemens Auto- Links to tips, tricks and downloads for functional or content
mation and Drives (A&D) – contains over 100 000 products with updates can be found at this address.
approximately 5 million potential drive system product variants. Order No. for CA 01, English International:
The SD configurator has been developed to facilitate selection CD-ROM: E86060-D4001-A110-C5-7600
of the correct motor and/or converter from the wide spectrum of DVD: E86060-D4001-A510-C5-7600
A&D SD products. It is integrated as a “selection aid” in this cat- Note: The SD configurator offline tool within CA 01 can be up-
alog. dated for the new 1LE1 motor series online over the Internet.
The SD configurator makes it easier to find the right drive solu-
tion. It supplies the correct order number as well as the corre-
sponding documentation.
It can display operating instructions, factory test certificate,
terminal box documentation, etc. and generates data sheets,
dimension drawings and a start-up calculation for the relevant
products.
Dimension sheet generator When a complete Order No. is entered with or without order
codes, a dimension drawing can be called up under the “Docu-
(part of the SD configurator) mentation” tab.
A dimension drawing can be created in the SD configurator for These dimension drawings can be presented in different views
every configurable motor. A dimension drawing can be re- and sections and printed.
quested for every other motor.
The corresponding dimension sheets can be exported, saved
and processed further in DXF format (interchange/import format
for CAD systems) or as bitmap graphics.
The SD configurator has been integrated into the CA 01 elec-
tronic catalog as a selection aid (for further information, see
above).
The interactive CA 01 catalog can be ordered from your local
Siemens sales representative or on the Internet at
http://www.siemens.com/automation/CA01.
At this address, you will also find links to Tips & Tricks and to
downloads for function or content updates.
Order No. for CA 01, English International
CD-ROM: E86060-D4001-A110-C5-7600
DVD: E86060-D4001-A510-C5-7600
Note:
The SD configurator offline tool within CA01 can be updated for
the new 1LE1 motor series online over the Internet.

© Siemens AG 2007

New Generation 1LE1
Dimensions
■ Dimensional drawings
1 Aluminum series 1LE1, frame sizes 100 to 160 - General Line motors with shorter delivery time
Type of construction IM B3
L
G_D081_EN_00181b
AG Eyebolts from
LL AS
frame size 100 L
L1
ED Integral feet
AD
only for
AF
EB
frame sizes 132 S/M
F
BE’ and 160 L/M have
AC
D1
BE 2 holes
D
BC at NDE
GA
H
BA K K' B
HA
DB E C B A BA BA'
Y BB AA BB
AB
Types of construction IM B5 and IM V1

For flange dimensions, see Page 1/98 (Z = the number of retaining holes)
L
G_D081_EN_00182
HH AG
LL AS
Eyebolts from
frame size 100 L
L1
AD
AF
EB
F
BE’
AC
D1
BE
D
E
GA
DB ED
For motor Dimension designation acc. to IEC

Frame Number
size of poles A AA AB AC AD AF AG AS B* BA BA’ BB BC BE BE’ C H HA Y 1)
100 L 2, 4, 6, 8 160 42 196 198 166 125.5 135 63.5 140 37.5 – 176 33.5 50 25 63 100 12 45
112 M 2, 4, 6, 8 190 46 226 222 177 136.5 135 63.5 140 35.4 – 176 26 50 25 70 112 12 52
132 S 2, 4, 6, 8 216 53 256 262 202 159.5 155 70.5 140 38 76 218 26.5 48 24 89 132 15 69
132 M 2, 4, 6, 8 216 53 256 262 202 159.5 155 70.5 178 38 76 218 26.5 48 24 89 132 15 69
160 M 2, 4, 6, 8 254 60 300 314 236.5 190 175 77.5 210 44 89 300 47 57 28.5 108 160 18 85
160 L 2, 4, 6, 8 254 60 300 314 236.5 190 175 77.5 254 44 89 300 47 57 28.5 108 160 18 85
* This dimension is assigned in DIN EN 50347 to the frame size listed.

1)
Additional information: not a standard dimension acc. to DIN 50347.

© Siemens AG 2007

New Generation 1LE1
Dimensions
■ Dimensional drawings (continued)

Aluminum series 1LE1, frame sizes 100 to 160 - General Line motors with shorter delivery time 1
G_D081_EN_00183b
L AG
LL AS Eyebolts from
L1 frame size 100 L
AD
Integral feet
AF
only for
EB
F
BE’ frame sizes 132 S/M
AC
and 160 L/M have
D1
BE
D
E C BC 2 holes
GA at NDE
H
ED BA K K' B
HA
DB B A BA BA'
Y BB AA BB
AB

L
G_D081_EN_00184
HH AG Eyebolts from
LL AS frame size 100 L
L1 AD
AF
F
BE’
D1
AC
BE
D
GA
DB ED
For motor Dimension designation acc. to IEC DE shaft extension

Frame Number
size of poles HH K K' L 1) L1 D1 LL D DB E EB ED F GA
100 L 2, 4, 6, 8 96.5 12 16 395.5 7 32 112 28 M10 60 50 5 8 31
112 M 2, 4, 6, 8 96 12 16 389 7 32 112 28 M10 60 50 5 8 31
132 S 2, 4, 6, 8 115.5 12 16 465 8.5 39 130 38 M12 80 70 5 10 41
132 M 2, 4, 6, 8 115.5 12 16 465 8.5 39 130 38 M12 80 70 5 10 41
160 M 2, 4, 6, 8 155 15 19 604 10 45 145 42 M16 110 90 10 12 45
160 L 2, 4, 6, 8 155 15 19 604 10 45 145 42 M16 110 90 10 12 45
1)
The length is specified as far as the tip of the fan cover.

© Siemens AG 2007

New Generation 1LE1
Dimensions

1 Aluminum series 1LE1, frame sizes 100 to 160 - self-ventilated energy-saving motors with improved/high efficiency
LC
G_D081_EN_00163c
L AG
LL Eyebolts from
AS
frame size 100 L
L1
LM
ED Integral feet
AD
only for
AF
EB
D1
DA
frame sizes 132 S/M
FA
F
AQ
AC
BE 2 holes
D
BC at NDE
GA EC GC
H
BA K EE K' AF' B CA
HA
DB E C B CA EA DC A BA BA'
Y BB AA AD' BB
AB
Types of construction IM B5 and IM V1

LC
G_D081_EN_00164
L
HH AG
LL
Eyebolts from
AS
frame size 100 L
L1
LM
AD
AF
D1
DA
FA
EB
F
BE’
AQ
AC
BE
D
E GC
GA EC
EE
DB ED EA DC

Frame Number
size of poles A AA AB AC AD AD’ AF AF’ AG AQ AS B* BA BA’ BB BC BE BE’ C CA* H HA Y 1)
100 L 2, 4, 6, 8 160 42 196 198 166 166 125.5 125.5 135 195 63.5 140 37.5 – 176 33.5 50 25 63 141.2 100 12 45
112 M 2, 4, 6, 8 190 46 226 222 177 177 136.5 136.5 135 195 63.5 140 35.4 – 176 26 50 25 70 129.7 112 12 52
132 S 2, 4, 6, 8 216 53 256 262 202 202 159.5 159.5 155 260 70.5 140 38 76 2) 218 3) 26.5 48 24 89 128.5 4) 132 15 69
132 M 2, 4, 6, 8 216 53 256 262 202 202 159.5 159.5 155 260 70.5 178 38 76 218 26.5 48 24 89 128.5 4) 132 15 69
160 M 2, 4, 6, 8 254 60 300 314 236.5 236.5 190 190 175 260 77.5 210 44 89 5) 300 6) 47 57 28.5 108 148 7) 160 18 85
160 L 2, 4, 6, 8 254 60 300 314 236.5 236.5 190 190 175 260 77.5 254 44 89 300 47 57 28.5 108 148 7) 160 18 85
* This dimension is assigned in DIN EN 50347 to the frame size listed. 4) With screwed-on feet, dimension CA is 166.5 mm.
1) 5)
Additional information: not a standard dimension acc. to DIN 50347. With screwed-on feet, dimension BA' is 44 mm.
2) With screwed-on feet, dimension BA' is 38 mm. 6) With screwed-on feet, dimension BB is 256 mm.
3) With screwed-on feet, dimension BB is 180 mm. 7) With screwed-on feet, dimension CA is 192 mm.

© Siemens AG 2007

New Generation 1LE1
Dimensions

Aluminum series 1LE1, frame sizes 100 to 160 - self-ventilated motors with improved/high efficiency 1
LC
G_D081_EN_00165c
L AG
LL AS
Eyebolts from
L1 frame size 100 L
LM
AD
Integral feet
AF
D1
DA
only for
FA
EB
F
AQ
AC
BE and 160 L/M have
D
E C BC 2 holes
GA EC GC at NDE
H
ED BA K EE K' AF' B CA
HA
DB B CA EA DC A BA BA'
Y BB AA AD' BB
AB

LC
G_D081_EN_00166
L
HH AG Eyebolts from
L1
LM
AD
AF
D1
DA
FA
F
BE’
AQ
AC
BE
D
GA EC GC
DC
DB ED EE
EA
For motor Dimension designation acc. to IEC DE shaft extension NDE shaft extension
Frame Number HH K K' L 1) L1 D1 LC LL LM D DB E EB ED F GA DA DC EA EC EE FA GC
size of poles
100 L 2, 4, 6, 8 96.5 12 16 395.5 7 32 454.2 112 428.5 28 M10 60 50 5 8 31 24 M8 50 40 5 8 27
112 M 2, 4, 6, 8 96 12 16 389 7 32 450 112 422 28 M10 60 50 5 8 31 24 M8 50 40 5 8 27
132 S 2, 4, 6, 8 115.5 12 16 465 8.5 39 535.5 130 500.5 38 M12 80 70 5 10 41 28 M10 60 50 5 8 31
132 M 2, 4, 6, 8 115.5 12 16 465 8.5 39 535.5 130 500.5 38 M12 80 70 5 10 41 28 M10 60 50 5 8 31
160 M 2, 4, 6, 8 155 15 19 604 10 45 730 145 638 42 M16 110 90 10 12 45 42 M16 110 90 10 12 45
160 L 2, 4, 6, 8 155 15 19 604 10 45 730 145 638 42 M16 110 90 10 12 45 42 M16 110 90 10 12 45
1)

© Siemens AG 2007

New Generation 1LE1
Dimensions

1 Aluminum series 1LE1, frame sizes 100 to 160 - self-ventilated motors with increased output and improved/high efficiency
LC
G_D081_EN_00170a
L AG
LL Eyebolts from
AS
frame size 100 L
L1
LM
ED
AD
AF
EB
D1
DA
FA
F
BE’
AQ
AC
BE
D
BC
GA EC GC
H
BA K EE K' AF'
HA
DB E C B CA EA DC A
Y BB AA AD'
AB
Type of construction IM B5 and IM V1

LC
G_D081_EN_00164
L
HH AG
LL
Eyebolts from
AS
frame size 100 L
L1
LM
AD
AF
D1
DA
FA
EB
F
BE’
AQ
AC
BE
D
E GC
GA EC
EE
DB ED EA DC

Frame Number A AA AB AC AD AD’ AF AF’ AG AQ AS B* BA BA’ BB BC BE BE’ C CA* H HA Y 1)
size of poles
100 L 2, 4, 6, 8 160 42 196 198 166 166 125.5 125.5 135 195 63.5 140 37.5 – 176 33.5 50 25 63 176.2 100 12 45
112 M 2, 4, 6, 8 190 46 226 222 177 177 136.5 136.5 135 195 63.5 140 35.4 – 176 26 50 25 70 155 112 12 52
132 M 2, 4, 6, 8 216 53 256 262 202 202 159.5 159.5 155 260 70.5 178 38 – 218 26.5 48 24 89 178.5 132 15 69
160 L 2, 4, 6, 8 254 60 300 314 236.5 236.5 190 190 175 260 77.5 254 44 – 300 47 57 28.5 108 208 160 18 85
* This dimension is assigned in DIN EN 50347 to the frame size listed.

1)
Additional information: not a standard dimension acc. to DIN 50347.

© Siemens AG 2007

New Generation 1LE1
Dimensions

Aluminum series 1LE1, frame sizes 100 to 160 - self-ventilated motors with increased output and improved/high efficiency 1
LC
G_D081_EN_00171a
L AG
LL AS Eyebolts from
L1 frame size 100 L
LM
AD
AF
D1
DA
FA
EB
F
BE’
AQ
AC
BE
D
E C BC
GA EC GC
H
ED BA K EE K' AF'
HA
DB B CA EA DC A
Y BB AA AD'
AB

LC
G_D081_EN_00166
L
HH AG Eyebolts from
L1
LM
AD
AF
D1
DA
FA
F
BE’
AQ
AC
BE
D
GA EC GC
DC
DB ED EE
EA
Frame Number HH K K' L 1) L1 D1 LC LL LM D DB E EB ED F GA DA DC EA EC EE FA GC
size of poles
100 L 2, 4, 6, 8 96.5 12 16 430.5 7 32 489.2 112 463.5 28 M10 60 50 5 8 31 24 M8 50 40 5 8 27
112 M 2, 4, 6, 8 96 12 16 414 7 32 475 112 447 28 M10 60 50 5 8 31 24 M8 50 40 5 8 27
132 M 2, 4, 6, 8 115.5 12 16 515 8.5 39 585.5 130 550.5 38 M12 80 70 5 10 41 28 M10 60 50 5 8 31
160 L 2, 4, 6, 8 155 15 19 664 10 45 790 145 698 42 M16 110 90 10 12 45 42 M16 110 90 10 12 45
1)

© Siemens AG 2007

New Generation 1LE1
Dimensions

1 Aluminum series 1LE1, frame sizes 100 to 160 - forced-air cooled motors without external fan and fan cover with improved/
high efficiency
LC
G_D081_EN_00173c
L AG
LL Eyebolts from
AS
frame size 100 L
ED Integral feet
AD
only for
AF
EB
DA
frame sizes 132 S/M
FA
F
AC
BE 2 holes
D
BC at NDE
GA EC GC
H
BA K EE K' AF' B CA
HA
DB E C B CA EA DC A BA BA'
Y BB AA AD' BB
AB
Type of construction IM B5 and IM V1

LC
G_D081_EN_00174
L
HH AG Eyebolts from
AD
AF
DA
FA
EB
F
BE’
AC
BE
D
E GC
GA EC
EE
DB ED EA DC

Frame Number A AA AB AC AD AD’ AF AF’ AG AS B* BA BA’ BB BC BE BE’ C CA* H HA Y 1)
size of poles
100 L 2, 4, 6, 8 160 42 196 197 166 166 125.5 125.5 135 63.5 140 37.5 – 176 33.5 50 25 63 – 100 12 45
112 M 2, 4, 6, 8 190 46 226 221 177 177 136.5 136.5 135 63.5 140 35.4 – 176 26 50 25 70 – 112 12 52
132 S 2, 4, 6, 8 216 53 256 261 202 202 159.5 159.5 155 70.5 140 38 76 2) 218 3) 26.5 48 24 89 – 132 15 69
132 M 2, 4, 6, 8 216 53 256 261 202 202 159.5 159.5 155 70.5 178 38 76 218 26.5 48 24 89 – 132 15 69
160 M 2, 4, 6, 8 254 60 300 314 236.5 236.5 190 190 175 77.5 210 44 89 4) 300 5) 47 57 28.5 108 – 160 18 85
160 L 2, 4, 6, 8 254 60 300 314 236.5 236.5 190 190 175 77.5 254 44 89 300 47 57 28.5 108 – 160 18 85
3)
* This dimension is assigned in DIN EN 50347 to the frame size listed. With screwed-on feet, dimension BB is 180 mm.
1) 4)
Additional information: not a standard dimension acc. to DIN 50347. With screwed-on feet, dimension BA' is 44 mm.
2) 5)
With screwed-on feet, dimension BA' is 38 mm. With screwed-on feet, dimension BB is 256 mm.

© Siemens AG 2007

New Generation 1LE1
Dimensions

Aluminum series 1LE1, frame sizes 100 to 160 - forced-air cooled motors without external fan and fan cover with improved/
high efficiency
1
LC
G_D081_EN_00175c
L AG
LL AS Eyebolts from
frame size 100 L
AD
Integral feet
AF
DA
only for
FA
EB
F

and 160 L/M have
AC
BE
D
E C BC 2 holes
GA EC GC at NDE
H
ED BA K EE K' AF' B CA
HA
DB B CA EA DC A BA BA'
Y BB AA AD' BB
AB

LC
G_D081_EN_00176
L
HH AG
Eyebolts from
LL AS
frame size 100 L
ZxS
AD
AF
DA
FA
F
BE’
AC
BE
D
GA EC GC
DB ED EE
EA DC
Frame Number HH K K' L LC LL D DB E EB ED F GA DA DC EA EC EE FA GC
size of poles
100 L 2, 4, 6, 8 96.5 12 16 321.5 – 112 28 M10 60 50 5 8 31 – – – – – – –
112 M 2, 4, 6, 8 96 12 16 311 – 112 28 M10 60 50 5 8 31 – – – – – – –
132 S 2, 4, 6, 8 115.5 12 16 380.5 – 130 38 M12 80 70 5 10 41 – – – – – – –
132 M 2, 4, 6, 8 115.5 12 16 380.5 – 130 38 M12 80 70 5 10 41 – – – – – – –
160 M 2, 4, 6, 8 155 15 19 510 – 145 42 M16 110 90 10 12 45 – – – – – – –
160 L 2, 4, 6, 8 155 15 19 510 – 145 42 M16 110 90 10 12 45 – – – – – – –

© Siemens AG 2007

New Generation 1LE1
Dimensions

1 Flange dimensions
In DIN EN 50347, flanges FF
with through holes and flang-
es FT with tapped holes are
assigned to frame sizes. The
designation of flange A and C
according to DIN 42948 (in-
G_D081_XX_00026
G_D081_XX_00027
valid since 09/2003) are also
listed for information purpos-
es. See the table below.
(Z = the number of retaining
holes)
Frame size Type of construction Flange type Flange with Dimension designation acc. to IEC
Through holes (FF/A)
Tapped holes (FT/C)
According to Acc. to LA LE M N P S T Z
DIN EN 50347 DIN 42948
100 L IM B5, IM B35, IM V1, IM V3 Flange FF 215 A 250 11 60 215 180 250 14.5 4 4
IM B14, IM B34, IM V18, IM V19 Standard flange FT 130 C 160 – 60 130 110 160 M8 3.5 4
112 M IM B5, IM B35, IM V1, IM V3 Flange FF 215 A 250 11 60 215 180 250 14.5 4 4
132 S, 132 M IM B5, IM B35, IM V1, IM V3 Flange FF 265 A 300 12 80 265 230 300 14.5 4 4
160 M, 160 L IM B5, IM B35, IM V1, IM V3 Flange FF 300 A 350 13 110 300 250 350 18.5 5 4
IM B14, IM B34, IM V18, IM V19 Standard flange FT 215 C 250 – 110 215 180 250 M12 4 4

© Siemens AG 2007

Appendix
Siemens contacts worldwide
At
http://www.siemens.com/automation/partner
you can find details of Siemens contact partners worldwide
responsible for particular technologies.
You can obtain in most cases a contact partner for
• technical support,
• spare parts/repairs,
• service,
• training,
• sales or
• consultation/engineering.
You start by selecting a
• country,
• product or
• sector.
By further specifying the remaining criteria you will find exactly
the right contact partner with his/her respective expertise.

© Siemens AG 2007

Appendix
A&D online services – Information and
ordering on the Internet and on CD-ROM
■ A&D in the WWW

A detailed knowledge of the range of products and services
available is essential when planning and configuring automation
systems. It goes without saying that this information must always
be fully up-to-date.
The Siemens Automation and Drives Group (A&D) has therefore
built up a comprehensive range of information in the World Wide
Web, which offers quick and easy access to all data required.
Under the address
http://www.siemens.com/automation
you will find everything you need to know about products, sys-
tems and services.
■ Product selection with the Offline Mall of Automation and Drives

Detailed information together with convenient interactive
functions:
The Offline Mall CA 01 covers more than 80,000 products and
thus provides a full summary of the Siemens Automation and
Drives product base.
Here you will find everything that you need to solve tasks in the
fields of automation, switchgear, installation and drives.
All information is linked into a user interface which is easy to
work with and intuitive.
After selecting the product of your choice, you can order at the
press of a button, by fax or by online link.
Information on the Offline Mall CA 01 can be found on the Inter-
net under
http://www.siemens.com/automation/ca01
or on CD-ROM or DVD.
■ Easy shopping with the A&D Mall

The A&D Mall is the virtual department store of Siemens AG on
the Internet. Here you have access to a huge range of products
presented in electronic catalogs in an informative and attractive
way.
Data transfer via EDIFACT allows the whole procedure from
selection through ordering to tracking of the order to be carried
out online via the Internet.
Numerous functions are available to support you.
For example, powerful search functions make it easy to find the
required products, which can be immediately checked for avail-
ability. Customer-specific discounts and preparation of quotes
can be carried out online as well as order tracking and tracing.
Please visit the A&D Mall on the Internet under:
http://www.siemens.com/automation/mall

© Siemens AG 2007

Appendix
Customer support –
Our services for every phase of your project
■ Technical consulting
Support in the planning and ting on product and system
designing of your project from questions right to the creation
detailed actual-state analysis, of the automation solution.1)
target definition and consul-
■ Optimization and upgrading

To enhance productivity and offer high-quality services in
save costs in your project, we optimization and upgrading.1)
■ Configuration and software engineering

Support in configuring and de-
I
veloping with customer-oriented
services from actual configura-
In the face of harsh competition you need optimum conditions to
tion to implementation of the
keep ahead all the time:
automation project.1)
a strong starting position, a sophisticated strategy and a team
for the necessary support – in every phase.
Service & Support from Siemens provides this support with a
complete range of different services for automation and drives.
In every phase: from planning and commissioning to mainte-
nance and upgrading.
Our specialists know when and where to act to keep the produc-
tivity and cost-effectiveness of your system running in top form.
■ Service on site
With Service On Site, we offer
services for startup and mainte-
■ Online support nance essential for ensuring
The comprehensive information system availability.
system available round the
In Germany
clock via Internet ranging from
Phone: 0180 50 50 444 1)
Product Support and Service &
(0.14 €/min. from the German
Support services to Support
fixed network)
Tools in the Shop.
In the United States, call
http://www.siemens.com/
toll-free:
automation/service&support
Phone: +1 800 333 7421
In Canada, call:
Phone: +1 888 303 3353
■ Technical support ■ Repairs and spare parts
Competent consulting in techni-
cal questions covering a wide In the operating phase of a ma-
range of customer-oriented ser- chine or automation system, we
vices for all our products and provide a comprehensive repair
systems. and spare parts service ensur-
ing the highest degree of oper-
Phone: +49 (0)180 50 50 222 ating safety and reliability.
Fax: +49 (0)180 50 50 223
(0.14 €/min. from the German In Germany
fixed network) Phone: 0180 50 50 448 1)
(0.14 €/min. from the German
E-Mail: fixed network)
[email protected]
In the United States, call
In the United States, call toll-free:
toll-free: Phone: +1 800 241 4453
Phone: +1 800 333 7421, In Canada, call:
Fax: +1 423 262 2200 Phone: +1 888 303 3353
E-Mail: solutions.support
@sea.siemens.com
In Canada, call:
Phone: +1 888 303 3353
E-Mail: [email protected]
In Asia:
Phone: +86 10 6475 7575,
Fax: +86 10 6474 7474
E-Mail:
[email protected]
2
1) You will find telephone numbers for other countries on our Internet site
http://www.siemens.com/automation/service&support

© Siemens AG 2007

Appendix
Customer support
■ Knowledge Base on CD-ROM

For those applications in which On the CD-ROM, you will also find a full text search and our
an online link to the Internet is Knowledge Manager to search for specific solutions. The CD-
not available, an extract from the ROM is updated every 4 months.
information area that can be
accessed free of charge is avai- As is the case with our online information on the Internet, the Ser-
lable on CD-ROM (Service & vice & Support Knowledge Base CD is available complete with
Support Knowledge Base). This 5 languages (English, German, French, Italian and Spanish).
CD-ROM contains all the prod- You can order the CD Service and Support Knowledge Base
uct information (FAQs, down- from your Siemens contact.
loads, tips and tricks, news) that
was available at the time the CD Order No.: 6ZB5310-0EP30-0BA2
was generated as well as gen- Ordering via the Internet
eral information about service (with the Automation Value Card or credit card) at:
and technical support.
http://www.siemens.com/automation/service&support
in the shop.
■ Automation Value Card

By specifying the card number and PIN, you have complete
access to the current range of Service and Support. The amount
for the service obtained is deducted in the form of credits from
the balance on your Automation Value Card.
All the offered services are priced in terms of credits indepen-
dently of national currencies, so you can use the Automation
Value Card worldwide.
Order Numbers for the Automation Value Card
Credits Order No.
200 6ES7 997-0BA00-0XA0
500 6ES7 997-0BB00-0XA0
1000 6ES7 997-0BC00-0XA0
10000 6ES7 997-0BG00-0XA0
Small card – lots of support
For detailed information about the offered services, visit our
The Automation Value Card is an integral part of the comprehen-
Internet site:
sive service concept with which Siemens Automation and Drives
accompanies you in every phase of your automation project. http://www.siemens.com/automation/service&support
Whether you require certain services from our Technical Support Service & Support à la Card: Some examples
or want to buy high-quality support tools in our online shop: You Technical Support
can always pay with the Automation Value Card. No costs for
processing invoices, transparent and secure. With the card "Priority" Priority handling for urgent cases
number that is only known to you and the associated PIN, you "24 h" Availability round-the-clock
can check your current balance at any time as well as all the
debits and credits. "Extended" Technical advice for complex questions
Support tools in the Support Shop
Services on the card. This is how it works.
"System Ready-to-use tools for design, analysis and checking
The card number and PIN are printed on the back of the Auto- Utilities"
mation Value Card. When it is supplied, the PIN is covered by a
scratch field so the full credit is guaranteed to be on the card. "Applications" Complete topics including fully tested software
"Functions & Modifiable function blocks to speed up your develop-
Samples" ments

© Siemens AG 2007

Appendix
Subject index
■ Subject index
Page Page
A N
A&D online services 2/2 National standards 1/5
Accessories 1/86 Non-standard voltages 1/8
Additional versions 1/31
Admissible axial load 1/25, 1/26 O
Admissible cantilever forces 1/24, 1/25 Options 1/79 ... 1/85
Application 1/2 Order No. code 1/40
Ordering data 1/44 … 1/77
B Ordering example 1/40
Balance 1/21 Outputs 1/9
Bearing selection table 1/23 Overall dimensions 1/87
Bearings 1/22 Overview 1/1
Benefits 1/2
Brakes 1/28, 1/31 P
Packaging 1/7
C Paint finish 1/5
CEMEP 1/1 Power factor 1/9
Colors 1/5 Preliminary selection of the motor 1/41
Conditions of sale and delivery 2/8 Protection devices that are motor temperature
Connection box 1/15 sensitive 1/13
Coolant temperature 1/11 Rated currents 1/8
Current-dependent protection devices 1/13 Rated speed 1/9
Currents 1/7 Rated torque 1/9
Customer support 2/3 Rating plates 1/10
Cut-away diagram 1/4 Recommendations for drive selection 1/39
Rotary pulse encoder 1/26,
D 1/32 … 1/34
Degrees of protection 1/20 Rotor 1/21
Diagrams of bearings 1/23
Dimension sheet generator 1/89 S
Dimensional drawings 1/90 … 1/98 Safety notes 1/7
Dimensions 1/87 … 1/98 SD configurator 1/89
Direction of rotation 1/9 Selection and ordering data 1/44 … 1/77
Documentation 1/7 Separately driven fan 1/27
Shaft 1/21
E Siemens contacts worldwide 2/1
Efficiency 1/1, 1/9 Site altitude 1/11
Energy balance 1/1 Spare parts 1/86
EPACT 1/1 Special versions 1/78 ... 1/85
Export regulations 2/8 Standard voltages 1/7
Extra rating plates 1/10 Standards 1/5
F T
Flange dimensions 1/98 Technical specifications 1/3
Frequencies 1/7 Test certificates 1/7
H Totally Integrated Automation 4
Heating 1/14 Types of construction 1/18
I V
Insulation 1/12 Ventilation 1/14
Vibration quantity 1/21
L Voltages 1/7, 1/78
Lubrication 1/22
W
M Welcome to Automation and Drives 2
Mechanical design 1/20 Windings 1/12
Metal surcharges 2/6
Modular technology 1/26
Motor connection 1/15
Motor protection 1/13

© Siemens AG 2007

Appendix
Metal surcharges
■ Explanation of the metal factor

Surcharges will be added to the prices of products that contain Weight method
silver, copper, aluminum, lead and/or gold if the respective basic
official prices for these metals are exceeded. The weight method uses the basic official price, the daily price
and the raw material weight. In order to calculate the surcharge,
The surcharges will be determined based on the following the basic official price must be subtracted from the daily price.
criteria: The result is then multiplied by the raw material weight.
• Official price of the metal The basic official price can be found in the table below using the
Official price on the day prior to receipt of the order or prior to number (2 to 9) of the respective digit of the metal factor. The raw
the release order (=daily price) for material weight can be found in the respective product descrip-
- silver (sale price of the processed material), tions.
- gold (sale price of the processed material)
Percentage method
Source: Umicore, Hanau
(http://www.metalsmanagement.umicore.com) Use of the percentage method is indicated by the letters A-Z at
and for the respective digit of the metal factor.
- copper (low DEL notation + 1%),
- aluminum (aluminum in cables) and The surcharge is increased – dependent on the deviation of the
- lead (lead in cables) daily price compared with the basic official price – using the
percentage method in “steps” and consequently offers
Source: German Trade Association for Cables and surcharges that remain constant within the framework of this
Conductors “step range”. A higher percentage rate is charged for each new
(http://www.kabelverband.de) step. The respective percentage level can be found in the table
• Metal factor of the products below.
Certain products are assigned a metal factor. The metal factor Metal factor examples
determines the official price as of which the metal surcharges
are charged and the calculation method used (weight or
LEA–––
percentage method). An exact explanation is given below.
Structure of the metal factor Basis for % surcharge: List price
The metal factor consists of several digits; the first digit indicates Silver: basis 150 €, step range 50 €, 0.5%
whether the method of calculation refers to the list price or a Copper: basis 150 €, step range 50 €, 0.1 %
discounted price (customer net price)
(L = list price / N = customer net price). No surcharge for aluminum
The remaining digits indicate the method of calculation used for No surcharge for lead
the respective metal. If no surcharge is added, a “-” is used. No surcharge for gold
1st digit List or customer net price using the percentage method
N – A 6– –
2nd digit for silver (AG)
3rd digit for copper (CU) Basis for % surcharge: Customer net price
4th digit for aluminum (AL) No surcharge for silver
5th digit for lead (PB) Copper: basis 150 €, step range 50 €, 0.1 %
6th digit for gold (AU) Aluminum acc. to weight, basic offic. price 225 €
No surcharge for lead
No surcharge for gold
– – 3– – –
No basis necessary
No surcharge for silver
Copper acc. to weight, basic official price150 €
No surcharge for aluminum
No surcharge for lead
No surcharge for gold
A&D/MZ_1/En 05.09.06

© Siemens AG 2007

Appendix
Metal surcharges
■ Values of the metal factor

Percentage Basic official Step range % surcharge % surcharge % surcharge % surcharge % surcharge
method price 1st step 2nd step 3rd step 4th step per additional
step
Official price Official price Official price Official price
151 € − 200 € 201 € − 250 € 251 € − 300 € 301 € − 350 €
A 150 50 0.1 0.2 0.3 0.4 0.1
B 150 50 0.2 0.4 0.6 0.8 0.2
C 150 50 0.3 0.6 0.9 1.2 0.3
D 150 50 0.4 0.8 1.2 1.6 0.4
E 150 50 0.5 1.0 1.5 2.0 0.5
F 150 50 0.6 1.2 1.8 2.4 0.6
G 150 50 0.7 1.4 2.1 2.8 0.7
H 150 50 1.2 2.4 3.6 4.8 1.2
I 150 50 1.6 3.2 4.8 6.4 1.6
J 150 50 1.8 3.6 5.4 7.2 1.8
K 150 50 2.0 3.5 5.0 6.5 1.5
L 150 50 2.2 4.4 6.6 8.8 2.2
M 150 50 2.5 5.0 7.5 10.0 2.5
176 € − 225 € 226 € − 275 € 276 € − 325 € 326 € − 375 €
O 175 50 0.1 0.2 0.3 0.4 0.1
P 175 50 0.2 0.4 0.6 0.8 0.2
Q 175 50 0.3 0.6 0.9 1.2 0.3
R 175 50 0.5 1.0 1.5 2.0 0.5
226 € − 275 € 276 € − 325 € 326 € − 375 € 376 € − 425 €
S 225 50 0.2 0.4 0.6 0.8 0.2
T 225 50 0.5 1.0 1.5 2.0 0.5
U 225 50 1.0 2.0 3.0 4.0 1.0
V 225 50 1.0 1.5 2.0 3.0 1.0
W 225 50 1.2 2.5 3.5 4.5 1.0
126 € − 150 € 151 € − 175 € 176 € − 200 € 201 € − 225 €
X 125 25 1.9 3.8 5.7 7.6 1.9
151 € − 175 € 176 € − 200 € 201 € − 225 € 226 € − 250 €
Y 150 25 0.3 0.6 0.9 1.2 0.3
401 € − 425 € 426 € − 450 € 451 € − 475 € 476 € − 500 €
Z 400 25 0.1 0.2 0.3 0.4 0.1
Price basis (1st digit)
L Charged on the list price
N Charged on the customer net price or discounted list price
Weight method Basic official
price
2 100
3 150
4 175
5 200 Calculation based on raw material weight
6 225
7 300
8 400
9 555
Misc.
− No metal surcharge
A&D/MZ_2/En 05.09.06
2

© Siemens AG 2007

Appendix
Conditions of sale and delivery
The texts of the Comprehensive Terms and Conditions of Sale
■ Terms and Conditions of Sale and Delivery and Delivery are available free of charge from your local
By using this catalog you can acquire hardware and software Siemens business office under the following Order Nos.:
products described therein from Siemens AG subject to the fol- • 6ZB5310-0KR30-0BA1
lowing terms. Please note! The scope, the quality and the condi- (for customers based in Germany)
tions for supplies and services, including software products, by
any Siemens entity having a registered office outside of Ger- • 6ZB5310-0KS53-0BA1
many, shall be subject exclusively to the General Terms and (for customers based outside of Germany)
Conditions of the respective Siemens entity. The following terms or download them from the Internet
apply exclusively for orders placed with Siemens AG. http://www.siemens.com/automation/mall
(Germany: A&D Mall Online-Help System)
For customers with a seat or registered office in Germany
The “General Terms of Payment” as well as the “General Condi-
tions for the Supply of Products and Services of the Electrical
and Electronics Industry” shall apply.
■ Export regulations
The products listed in this catalog may be subject to European /
For software products, the “General License Conditions for German and/or US export regulations.
Software Products for Automation and Drives for Customers with
a Seat or registered Office in Germany” shall apply. Therefore, any export requiring a license is subject to approval
by the competent authorities.
For customers with a seat or registered office outside of According to current provisions, the following export regulations
Germany must be observed with respect to the products featured in this
The “General Terms of Payment” as well as the “General Condi- catalog:
tions for Supplies of Siemens, Automation and Drives for Cus-
tomers with a Seat or registered Office outside of Germany” shall
apply. AL Number of the German Export List
For software products, the “General License Conditions for Soft- Products marked other than “N” require an export
ware Products for Automation and Drives for Customers with a license.
Seat or registered Office outside of Germany” shall apply. In the case of software products, the export des-
ignations of the relevant data medium must also
General be generally adhered to.
The dimensions are in mm. In Germany, according to the Ger- Goods labeled with an “AL” not equal to “N” are
man law on units in measuring technology, data in inches only subject to a European or German export authori-
apply to devices for export. zation when being exported out of the EU.
Illustrations are not binding. ECCN Export Control Classification Number.
Insofar as there are no remarks on the corresponding pages, Products marked other than “N” are subject to a
- especially with regard to data, dimensions and weights given - reexport license to specific countries.
these are subject to change without prior notice.
In the case of software products, the export
The prices are in € (Euro) ex works, exclusive packaging. designations of the relevant data medium must
The sales tax (value added tax) is not included in the prices. also be generally adhered to.
It shall be debited separately at the respective rate according to Goods labeled with an “ECCN” not equal to “N”
the applicable legal regulations. are subject to a US re-export authorization.
Prices are subject to change without prior notice. We will debit
the prices valid at the time of delivery. Even without a label or with an “AL: N” or “ECCN: N”, authoriza-
Surcharges will be added to the prices of products that contain tion may be required due to the final destination and purpose for
silver, copper, aluminum, lead and/or gold, if the respective ba- which the goods are to be used.
sic official prices for these metals are exceeded. These sur- The deciding factors are the AL or ECCN export authorization
charges will be determined based on the official price and the indicated on order confirmations, delivery notes and invoices.
metal factor of the respective product.
Errors excepted and subject to change without prior notice.
The surcharge will be calculated on the basis of the official price
on the day prior to receipt of the order or prior to the release or- A&D/VuL_mit MZ/En 05.09.06
der.
The metal factor determines the official price as of which the
metal surcharges are charged and the calculation method used.
The metal factor, provided it is relevant, is included with the price
information of the respective products. An exact explanation of
the metal factor can be found on the page entitled “Metal
surcharges”.

D81-1_N_en_U3.fm Seite 2 Montag, 17. September 2007 11:51 11
© Siemens AG 2007
Catalogs of the
Automation and Drives Group (A&D)
Further information can be obtained from our branch offices listed
in the appendix or at www.siemens.com/automation/partner
Automation and Drives Catalog Industrial Communication for Catalog
Interactive catalog on CD-ROM and on DVD Automation and Drives IK PI
• The Offline Mall of Automation and Drives CA 01
Low-Voltage
Automation Systems for Machine Tools
Controls and Distribution – LV 1
SINUMERIK & SIMODRIVE NC 60 SIRIUS, SENTRON, SIVACON
SINUMERIK & SINAMICS NC 61 Controls and Distribution – LV 1 T
Technical Information
Drive Systems SIRIUS, SENTRON, SIVACON
Variable-Speed Drives SIDAC Reactors and Filters LV 60
SINAMICS G110/SINAMICS G120 D 11.1 SIVENT Fans LV 65
Inverter Chassis Units SIVACON 8PS Busbar Trunking Systems LV 70
SINAMICS G120D
Distributed Frequency Inverters
SINAMICS G130 Drive Converter Chassis Units, D 11 Motion Control System SIMOTION PM 10
SINAMICS G150 Drive Converter Cabinet Units
SINAMICS GM150/SINAMICS SM150 D 12
Medium-Voltage Converters Process Instrumentation and Analytics
SINAMICS S120 Drive Converter Systems D 21.1 Field Instruments for Process Automation FI 01
SINAMICS S150 Drive Converter Cabinet Units D 21.3 Measuring Instruments for Pressure,
Differential Pressure, Flow, Level and Temperature,
Asynchronous Motors Standardline D 86.1 Positioners and Liquid Meters
Synchronous Motors with Permanent-Magnet D 86.2 PDF: Indicators for panel mounting MP 12
Technology, HT-direct
SIREC Recorders and Accessories MP 20
DC Motors DA 12
SIPART, Controllers and Software MP 31
SIMOREG DC MASTER 6RA70 Digital Chassis DA 21.1
Converters SIWAREX Weighing Systems WT 01
SIMOREG K 6RA22 Analog Chassis Converters DA 21.2 Continuous Weighing and Process Protection WT 02
SIMOREG DC MASTER 6RM70 Digital Converter DA 22 Process Analytical Instruments PA 01
Cabinet Units PDF: Process Analytics, PA 11
SIMOVERT PM Modular Converter Systems DA 45 Components for the System Integration
SIEMOSYN Motors DA 48
MICROMASTER 410/420/430/440 Inverters DA 51.2 SIMATIC Industrial Automation Systems
MICROMASTER 411/COMBIMASTER 411 DA 51.3 SIMATIC PCS Process Control System ST 45
SIMOVERT MASTERDRIVES Vector Control DA 65.10 Products for Totally Integrated Automation and ST 70
SIMOVERT MASTERDRIVES Motion Control DA 65.11 Micro Automation
Synchronous and asynchronous servomotors for DA 65.3 SIMATIC PCS 7 Process Control System ST PCS 7
SIMOVERT MASTERDRIVES Add-ons for the SIMATIC PCS 7 ST PCS 7.1
SIMODRIVE 611 universal and POSMO DA 65.4 Process Control System
Low-Voltage Three-Phase-Motors Migration solutions with the SIMATIC PCS 7 ST PCS 7.2
Process Control System
IEC Squirrel-Cage Motors D 81.1
pc-based Automation ST PC
IEC Squirrel-Cage Motors: New Generation 1LE1 D 81.1 N
SIMATIC Control Systems ST DA
PDF: Geared Motors M 15
Automation Systems for Machine Tools SIMODRIVE NC 60
• Main Spindle/Feed Motors SIMATIC Sensors
• Converter Systems SIMODRIVE 611/POSMO Sensors for Factory Automation FS 10
Automation Systems for Machine Tools SINAMICS NC 61
• Main Spindle/Feed Motors Systems Engineering
• Drive System SINAMICS S120 Power supplies SITOP power KT 10.1
Drive and Control Components for Hoisting Equipment HE 1 System cabling SIMATIC TOP connect KT 10.2
Electrical Installation Technology

System Solutions
PDF: ALPHA Small Distribution Boards and ET A1
Distribution Boards, Terminal Blocks Applications and Products for Industry are part of the
interactive catalog CA 01
PDF: ALPHA 8HP Molded-Plastic Distribution System ET A3
PDF: BETA Low-Voltage Circuit Protection ET B1
PDF: DELTA Switches and Socket Outlets ET D1 TELEPERM M Process Control System
GAMMA Building Controls ET G1 PDF: AS 488/TM automation systems PLT 112
Human Machine Interface Systems SIMATIC HMI ST 80
PDF: These catalogs are only available as pdf files.
A&D/3U/En 21.08.07
© Siemens AG 2007
T3X(#Y2 2- Y&W,%# 5'2&-32 .0'-0 ,-2'Y# 8 I'1.- >EA=A 8 NL =F=D ?=;= J >>? J, < D??@@A 8 R0',2#" ', L#0+W,6 8 9 T'#+#,1 GL ?==D
---0+%#'#(+0I)'1'),)*+
D%#'#(+ 9= ;&# ',$-/+<1'-, ./-3'"#" ', 1&'0 ><1<*-% >-,1<',0 "#0>/'.1'-,0 -/

>&</<>1#/'01'>0 -$ .#/$-/+<,># 4&'>& ', ><0# -$ <>12<* 20# "- ,-1 <*4<60
G32-+W2'-, W," I0'4#1 <..*6 <0 "#0>/'=#" -/ 4&'>& +<6 >&<,%# <0 < /#02*1 -$ $2/1&#/ "#3#*-.+#,1
T2W,"W0" I0'4#1 -$ 1&# ./-"2>107 8, -=*'%<1'-, 1- ./-3'"# 1&# /#0.#>1'3# >&</<>1#/'01'>0 0&<**
-,*6 #5'01 '$ #5./#00*6 <%/##" ', 1&# 1#/+0 -$ >-,1/<>17 83<'*<='*'16 <,"
R-12$WY& @> E=
1#>&,'><* 0.#>'$'><1'-,0 </# 02=(#>1 1- >&<,%# 4'1&-21 ,-1'>#7
F>=B= JSOGQLJQ
LJSPGQV 8** ./-"2>1 "#0'%,<1'-,0 +<6 =# 1/<"#+</)0 -/ ./-"2>1 ,<+#0 -$
:'#+#,0 89 -/ 02..*'#/ >-+.<,'#0 4&-0# 20# =6 1&'/" .</1'#0 $-/ 1&#'/ -4,
555;1'#+#,1;Y-+<W32-+W2'-, .2/.-0#0 >-2*" 3'-*<1# 1&# /'%&10 -$ 1&# -4,#/07
B*"#* A)0 <86262/>5583/9343/94/7622

1&,-4&%*5#" 2&*&() " 0/. 3'+$(("%-.5#" 2&*&() 04(4$%# 2")' 1 /,*, 2 * 36(%5"& -++. © Siemens AG 2007

@bebcd 3? 3 @bebcd 3? 3 @bebcd 3? 3

Uploaded by

Copyright:

Available Formats

@bebcd 3? 3 @bebcd 3? 3 @bebcd 3? 3

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

@bebcd 3? 3 @bebcd 3? 3 @bebcd 3? 3

Uploaded by

Copyright:

Available Formats

© Siemens AG 2007

?)-/F)&,G$# :G,G&)$ A#-+ ; 8303 A . BI,)H#* 4227

SINAMICS G110/SINAMICS G120 D 11.1

IEC Squirrel-Cage Motors 4 • Totally Integrated Automation

New Generation 1LE1 New Generation 1LE1

Supersedes: General Line motors

Self-ventilated energy-saving motors

Siemens Automation and Drives.

More than 70,000 people aiming for the same goal:

We offer you a comprehensive portfolio for sustained

Learn for yourself the potential our products and

Your regional Siemens contact can provide more infor-

2 Siemens D 81.1 N · October 2007

Siemens D 81.1 N · October 2007 3

Sharpen your competitive edge.

With Totally Integrated Automation (TIA), Siemens is the only

6=< 1 @*/#-,-'.# H#.+0-O# G(M**'*%

;+#,@.&*)- 9#0#' IBD=JB> G>I <

G-+O#.. B*./-0)#*/M/'+* IBD=JB> I#*.+-.

4 Siemens D 81.1 N · October 2007

It goes without saying that you profit from Totally Integrated

IBD=JB> E@J IBD=JB> >+*/-+((#-. IBD=JB> ADB IM$#/4 B*/#%-M/#"

IBHBKI B*"0./-'M( >+*/-+(.

Siemens D 81.1 N · October 2007 5

Protecting the environment

Environmental protection will continue to grow in importance

We are convinced that every individual - and especially

Many of our products and systems comply with the EC Directive

Our commitment goes well beyond compliance with the rele-

6 Siemens D 81.1 N · October 2007

IEC Squirrel-Cage Motors

Siemens D 81.1 N · October 2007 1/1

IEC Squirrel-Cage Motors

1/2 Siemens D 81.1 N · October 2007

IEC Squirrel-Cage Motors

Siemens D 81.1 N · October 2007 1/3

IEC Squirrel-Cage Motors

$ Motor protection Page 1/13 ( Bearings and lubrication Page 1/22

1/4 Siemens D 81.1 N · October 2007

IEC Squirrel-Cage Motors

Colors and paint finish

Siemens D 81.1 N · October 2007 1/5

IEC Squirrel-Cage Motors

1/6 Siemens D 81.1 N · October 2007

IEC Squirrel-Cage Motors

Siemens D 81.1 N · October 2007 1/7

IEC Squirrel-Cage Motors

1 The tolerance laid down by DIN EN 60034-1 applies to all non-

1/8 Siemens D 81.1 N · October 2007

IEC Squirrel-Cage Motors

Siemens D 81.1 N · October 2007 1/9

IEC Squirrel-Cage Motors

400 50 29,5 15 0,82 89,4% 1460 380-420 30,0-30,2

1 Machine type: Three-phase 13 Voltage range [V]

1/10 Siemens D 81.1 N · October 2007

IEC Squirrel-Cage Motors

Siemens D 81.1 N · October 2007 1/11

IEC Squirrel-Cage Motors

1/12 Siemens D 81.1 N · October 2007

G-+O#.. B./-0)#/M/'+* IBD=JB> I#*.+-.

IBD=JB> E@J IBD=JB> >+/-+((#-. IBD=JB> ADB IM$#/4 B/#%-M/#"

IBHBKI B"0./-'M( >+/-+(.