DC/DC Converters

TEN 50WI Series, 50 Watt

Features
CB
Scheme

◆ Very high power density:

50 W in 1” x 2” x 0.4” package
◆ Wide 4:1 input range
◆ Excellent efficiency up to 92 %
◆ Operating temperature range
–40°C to +80°C
◆ Protection against over-temperature
◆ No minimum load required
◆ Output voltage adjustable
◆ Remote On/Off
◆ I/O isolation 1500 VDC
◆ 3-year product warranty The TEN 50WI Series is a range of isolated high performance DC/DC converter
modules. With a very high efficiency of up to 92% and the use of highest reliable
components these 50 W converters can be packed into the standard 1.0” x 2.0”
casing. The 10 models have a wide 4:1 input voltage range and a tight output
voltage regulation. They do not need a minimum load and offer a high efficiency
also at low load conditions. The output voltage is adjustable by external resistor.
Remote On/Off and protection against overload and short circuit are standard
features of these converters.
Typical applications are in mobile equipment, instrumentation, distributed power
architectures in communication and industrial electronics and everywhere where
space on the PCB is critical.

Models
Order code Input voltage range Output voltage Output current max. Efficiency
TEN 50-2410WI 3.3 VDC 10‘000 mA 90 %
TEN 50-2411WI 5.0 VDC 10’000 mA 91 %
9 – 36 VDC
TEN 50-2412WI 12 VDC 4‘170 mA 92 %
(nominal 24 VDC)
TEN 50-2413WI 15 VDC 3‘330 mA 92 %
TEN 50-2415WI 24 VDC 2‘080 mA 91 %
TEN 50-4810WI 3.3 VDC 10‘000 mA 90 %
TEN 50-4811WI 5.0 VDC 10’000 mA 91 %
18 – 75 VDC
TEN 50-4812WI 12 VDC 4‘170 mA 92 %
(nominal 48 VDC)
TEN 50-4813WI 15 VDC 3‘330 mA 92 %
TEN 50-4815WI 24 VDC 2‘080 mA 91 %

http://www.tracopower.com Page 1 of 4
 DC/DC Converters
TEN 50WI Series 50 Watt

Input Specifications
Input current at no load (nominal input voltage) 24 Vin models: 80 mA typ
48 Vin models: 50 mA typ.
Recommended input fuse (slow blow) 24 Vin models: 1000 mA
48 Vin models: 500 mA
Surge voltage (100 msec. max.) 24 Vin models: 50 V max.
48 Vin models: 100 V max.
Reflected input ripple current 24Vin models: 40 mA typ.
48Vin models: 30 mA typ.
Conducted noise (input) EN 55022 class A, FCC part 15 level A
with external LC see application note
Start-up voltage / under voltage shut down 24 Vin models: 9 VDC max./ 7.5 VDC typ.
48 Vin models: 18 VDC max./ 16 VDC typ.
EMC immunity – ESD (electrostatic discharge) EN 61000-4-2, air ±8 kV, contact ±6 kV,
perf. criteria A
– Radiated immunity EN 61000-4-3, 10 V/m, perf. criteria A
– Fast transient / surge (with external input capacitor) EN 61000-4-4, ±2 kV, perf. criteria A
EN 61000-4-5, ±1 kV perf. criteria A
Nippon chemi-con KY 220 µF, 100 V, ESR 48 mOhm
– Conducted immunity EN 61000-4-6, 10 Vrms, perf. criteria A
Output Specifications
Voltage set accuracy ±1.0 % max.
Output voltage adjustment range 24 VDC models: +20 / –10 %
other models: ±10 %
Regulation – Input variation Vin min. to Vin max. 0.5 % max.
– Load variation 0 – 100 % 0.5 % max.
Minimum load not required
Temperature coefficient ±0.02 %/K
Ripple and noise (20 MHz Bandwidth) 3.3 & 5.0 VDC models: 100 mVpk-pk. typ.
other models: 150 mVpk-pk typ.
with 1µF MLCC and a 10µF tantalum capacitor
Transient response (alignment to 1% at load step change 75% to 100% ) 250 µs typ.
Output current limitation at 150% of Iout max.
Short circuit protection hiccup mode, automatic recovery
Capacitive load 3.3 VDC models: 26’000 µF max.
5.0 VDC models: 17’000 µF max.
12.0 VDC models: 3’000 µF max.
15.0 VDC models: 2’000 µF max.
24.0 VDC models: 750 µF max.

All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated.

http://www.tracopower.com Page 2 of 4
 DC/DC Converters
TEN 50WI Series 50 Watt

General Specifications
Temperature ranges – Operating (natural convection 20 LFM) –40°C to +80°C (with derating)
– Operating with heat sink (natural convection 20 LFM) –40°C to +85°C (with derating)
– Case temperature +105°C max.
– Storage –50°C to +125°C
Load derating – without heat sink 2.0 %/K above +55°C
(natural convection 20 LFM, – with heat sink 2.5 %/K above +65°C
typical values over series)
Thermal impedance – Natural convection 20 LFM 12°C/W
– Natural convection 20 LFM with heatsink 10°C/W
Humidity (non condensing) 95 % rel H max.
Reliability, calculated MTBF (MIL-HDBK-217F, at +25°C, ground benign) >230’900 h
Isolation voltage (60 sec.) – Input/Output 1500 VDC
Isolation capacitance – Input/Output 2200 pF max. (100 kHz, 1 V)
Isolation resistance – Input/Output >1000 Mohm (500 VDC)
Switching frequency 285 kHz typ.
Remote On/Off – On: 3.5 to 12 VDC to -Vin or open circuit.
– Off: 0 to +1.2 VDC or short circuit to -Vin
– Off idle current: 2.5 mA typ.
Safety standards CAN/CSA-C22.2 No 60950-1-07, 2nd ed; A1:2011
ANSI/UL No. 60950-1, 2nd ed.; A1:2011,
IEC 60950-1:2005 (2nd edition); Am 1:2009
EN 60950-1:2006/A11:2009/A1:2010/12:2011
– Certification documents www.tracopower.com/overview/ten50wi
Physical Specifications
Casing material alluminium alloy, 6-side shielded, insulating
baseplate
Potting material epoxy (UL 94V-0 rated)
Weight 34 g (1.05 oz)
Soldering temperature max. 260°C / 10 sec. (1.5 mm from casing)
Environmental compliance – Reach www.tracopower.com/info/reach-declaration.pdf
– RoHS directive 2011/65/EU

Supporting documents: www.tracopower.com/overview/ten50wi

All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated.

http://www.tracopower.com Page 3 of 4
 DC/DC Converters
TEN 50WI Series 50 Watt

Outline Dimensions

50.8

(0.1)
2.54
(2.0)
Pin-Out
(0.1)
2.54

4 Pin Single
1

10.16
(0.4)
10.16 5.08
(0.4) (0.2)

1 +Vin (Vcc)
2

25.4 (1.0)
20.32
(0.8)
Bottom View 5 2 –Vin (GND)
3 Remote On/Off
3 6 4 +Vout

45.72 (1.8) 2.54 (0.1) 5 –Vout

6 Trim

Dimensions in [mm], () = Inch

(0.22) (0.43)
11.0

Pin diameter: 1.0 ±0.05 (0.04 ±0.002)

Pin pitch tolerance: ±0.13 (±0.005)
5.5

Case tolerances: ±0.25 (±0.01)

Heat-sink TEN-HS6 (optional) Order code: TEN-HS6

(cont.: heat-sink, thermal pad, 2 clamps)
Material: Aluminum
Heat-sink Finish: Anodic treatment (black)
Thermal pad Weight: 9 g (0.31oz) without converter
Clamp
Converter Thermal impedance after assembling: 10 K/W

31.1 (1.22)

18.0 (0.71) Note:

max.
Before attaching the heatsink, the product
label on converter has to be removed for
29.0 (1.14)

optimal performance.
max.

For volume orders we can supply the

converters with heatsink already mounted.
Please contact us for a relative quotation.

Specifications can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com
Rev. July 11, 2018
www.tracopower.com Page 4 of 4