eMachines D720/D520 Series Service Guide

Service guide files and updates are available on the ACER/CSD web; for more information, please refer to http://csd.acer.com.tw

PRINTED IN TAIWAN

Revision History
Please refer to the table below for the updates made on eMachines D720/D520 Series service guide.
Date Chapter Updates

II

Copyright
Copyright 2008 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated.

Disclaimer
The information in this guide is subject to change without notice. Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software.

Acer is a registered trademark of Acer Corporation. Intel is a registered trademark of Intel Corporation. Pentium and Pentium II/III are trademarks of Intel Corporation. Other brand and product names are trademarks and/or registered trademarks of their respective holders.

III

Conventions
The following conventions are used in this manual: SCREEN MESSAGES NOTE Denotes actual messages that appear on screen. Gives bits and pieces of additional information related to the current topic. Alerts you to any damage that might result from doing or not doing specific actions. Gives precautionary measures to avoid possible hardware or software problems. Reminds you to do specific actions relevant to the accomplishment of procedures.

WARNING

CAUTION

IMPORTANT

IV

Preface
Before using this information and the product it supports, please read the following general information. 1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such cases, please contact your regional offices or the responsible personnel/channel to provide you with further technical details. Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on your regional web or channel. If, for whatever reason, a part number change is made, it will not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and service of customer machines.

2.

VI

Table of Contents
System Specifications 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Your Acer Notebook tour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Closed Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Left View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Right View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 TouchPad Basics (with fingerprint reader) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Using the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Lock Keys and embedded numeric keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Windows Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Hot Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Special Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Using the System Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Acer GridVista (dual-display compatible) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Hardware Specifications and Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

System Utilities

21

BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Navigating the BIOS Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 BIOS Flash Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 DOS Flash Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 WinFlash Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Remove HDD/BIOS Password Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Machine Disassembly and Replacement

41

Disassembly Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Pre-disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 External Module Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 External Modules Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Removing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 Removing the Lower Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 Removing the DIMM Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 Removing the WLAN Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 Removing the Hard Disk Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 Removing the Optical Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Main Unit Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 Main Unit Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 Removing the Switch Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 Removing the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

VII

Table of Contents
Removing the Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 Removing the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Removing the Upper Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 Removing the TouchPad Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Removing the Speaker Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Removing the Power Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 Removing the Modem Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 Removing the Main Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71 Removing the CPU Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 Removing the Thermal Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74 Removing the CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 LCD Module Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 LCD Module Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 Removing the LCD Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 Removing the Inverter Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78 Removing the Camera Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 Removing the LCD Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80 Removing the LCD Brackets and FPC Cable . . . . . . . . . . . . . . . . . . . . . . . . . . .81 Removing the Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 Removing the MIC Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 LCD Module Reassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84 Replacing the LCD Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84 Replacing the LCD Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88 Main Module Reassembly Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89 Replacing the CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89 Replacing the Thermal Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89 Replacing the CPU Fan Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90 Replacing the Mainboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90 Replacing the Modem Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 Replacing the Power Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92 Replacing the Speaker Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93 Replacing the TouchPad Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95 Replacing the Upper Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95 Replacing the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97 Replacing the Antenna Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 Replacing the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100 Replacing the Switch Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101 Replacing the ODD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 Replacing the Hard Disk Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 Replacing the WLAN Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104 Replacing the DIMM Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104 Replacing the Lower Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105 Replacing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106

Troubleshooting

107

Common Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 Power On Issue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108 No Display Issue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 Random Loss of BIOS Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 LCD Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 Built-In Keyboard Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 TouchPad Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 Internal Speaker Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 Internal Microphone Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114 HDD Not Operating Correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
VIII

Table of Contents
ODD Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116 Modem Function Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119 Wireless Function Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119 Thermal Unit Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120 External Mouse Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120 Other Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121 Intermittent Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122 Undetermined Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122 Post Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123 Sec: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123 Memory: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123 BDS & Specific action: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124 Each PEIM entry point used in 80_PORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . .125 Each Driver entry point used in 80_PORT . . . . . . . . . . . . . . . . . . . . . . . . . . . .125 Each SmmDriver entry point used in 80_PORT . . . . . . . . . . . . . . . . . . . . . . . .128

Jumper and Connector Locations

129

Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .130 Clearing Password Check and BIOS Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . .131 Clearing Password Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131 BIOS Recovery by Crisis Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132

FRU (Field Replaceable Unit) List

133

eMachines D720/D520 Exploded Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 Main Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 LCD Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .135 eMachines D720/D520 FRU List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136 Screw List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140

Model Definition and Configuration

142

eMachines D720/D520 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .142 Model Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .142

Test Compatible Components Online Support Information Index

153 161 163

Microsoft Windows Vista Environment Test . . . . . . . . . . . . . . . . . . . . . . . . . . . .154

IX

Table of Contents

Chapter 1

System Specifications
Features
Below is a brief summary of the computers many features:

Operating System

Genuine Windows Vista

Platform

Intel Pentium dual-core processor* Intel Celeron processor* Mobile Intel GL40 Express Chipset IEEE 802.11b/g

System Memory

Dual-channel support Up to 2 GB of DDR2 667 MHz memory, upgradeable to 4 GB using two soDIMM modules

Display and graphics

14.1" WXGA 1280 x 800 Mobile Intel GL40 Express Chipset

Storage subsystem

2.5" hard disk drive Optical drive option:

DVD-Super Multi double-layer drive* DVD/CD-RW combo drive*

Audio

Two built-in stereo speakers High-definition audio support MS-Sound compatible Built-in microphone

Dimensions and Weight

340.4 (W) x 247 (D) x 22.9/42.3 (H) mm (13.4 x 9.7 x 0.9/1.6 inches) 2.40 kg (5.29 lbs.) with 6-cell battery pack

Chapter 1

Communication

Integrated webcam* WLAN: IEEE 802.11b/g LAN: Fast Ethernet; Wake-on-LAN ready

Privacy control

BIOS user, supervisor, HDD passwords Kensington lock slot

Power subsystem

ACPI 3.0 48.8 W 4400 mAh 3-pin 65 W AC adapter ENERGY STAR 4.0*

Special keys and controls

88-/89-key keyboard Touchpad pointing device

I/O interface

USB 2.0 port External display (VGA) port Headphones/speaker/line-out jack Microphone-in jack Line-in jack Ethernet (RJ-45) port DC-in jack for AC adapter

Environment

Temperature:

Operating: 5 C to 35 C Non-operating: -20 C to 65 C

Humidity (non-condensing):

Operating: 20% to 80%

Non-operating: 20% to 80% NOTE: Items marked with * denote only selected models.

Chapter 1

System Block Diagram

Chapter 1

Your Acer Notebook tour

After knowing your computer features, let us show you around your new computer.

Front View

No. 1 2 3 4 5

Icon

Item Microphone Integrated webcam Display screen Power button Wireless LAN communication button/indicator Speakers Keyboard Palmrest

Description Internal microphone for sound recording. Web camera for video communication (for selected models). Also called Liquid-Crystal Display (LCD), displays computer output. Turns the computer on and off. Enables/disables the wireless LAN function. Indicates the status of wireless LAN communication. Left and right speakers deliver stereo audio output. For entering data into your computer. Comfortable support area for your hands when you use the computer.

6 7 8

Chapter 1

No. 9 10 11

Icon

Item TouchPad Click buttons (left and right) Power

Description Touch-sensitive pointing device which functions like a computer mouse. The left and right buttons function like the left and right mouse buttons. Indicates the computer's power status.

Battery

Indicates the computer's battery status. 1. Charging: The light shows amber when the battery is charging. 2. Fully charged: The light shows green when in AC mode. Indicates when the hard disk drive is active. Lights up when Num Lock is activated. Lights up when Caps Lock is activated.

HDD Num Lock Caps Lock

NOTE: The Power and Battery indicators are visible even when the computer cover is closed

Closed Front View

No. 1

Icon Latch

Item

Description Locks and releases the lid

Rear View

No. 1

Icon

Item Ventilation slots

Description Enable the computer to stay cool, even after prolonged use.

Chapter 1

Left View

No. 1 2 3

Icon

Item Ethernet (RJ-45) port External display (VGA) port USB 2.0 ports Line-in jack Microphone-in jack Headphones/ speaker/line-out jack

Description Connects to an Ethernet 10/100-based network. Connects to a display device (e.g. external monitor, LCD projector). Connect to USB 2.0 devices (e.g. USB mouse, USB camera). Accepts audio line-in devices (e.g., audio CD player, stereo walkman, mp3 player). Accepts input from external microphones. Connects to audio line-out devices (e.g. speakers, headphones).

Chapter 1

Right View

No. 1

Icon

Item Kensington lock slot

Description Connects to a Kensington-compatible computer security lock. Note: Wrap the computer security lock cable around an immovable object such as a table or handle of a locked drawer. Insert the lock into the notch and turn the key to secure the lock. Some keyless models are also available. Internal optical drive; accepts CDs or DVDs. Lights up when the optical drive is active. Ejects the optical disk from the drive. Ejects the optical drive tray when the computer is turned off. Note: Insert a paper clip into the emergency eject hole to eject the optical drive tray when the computer is off. Connects to an AC adapter

2 3 4 5

Optical drive Optical disk access indicator Optical drive eject button Emergency eject hole

DC-in jack

Chapter 1

Bottom View

No. 1 2 3 4 5 6

Icon

Item Battery bay Battery release latch Memory compartment Hard disk bay Battery lock Ventilation slots and cooling fan

Description Houses the computer's battery pack. Releases the battery for removal. Houses the computer's main memory. Houses the computer's hard disk (secured with screws). Locks the battery in position. Enable the computer to stay cool, even after prolonged use. Note: Do not cover or obstruct the opening of the fan.

Chapter 1

Indicators
The computer has several easy-to-read status indicators. The front panel indicators are visible even when the computer cover is closed. Icon Power Function Description Indicates the computer's power status.

Battery HDD Num Lock Caps Lock

Indicates the computer's battery status. Indicates when the hard disk drive is active. Lights up when Num Lock is activated. Lights up when Caps Lock is activated.

NOTE: 1. Charging: The light shows amber when the battery is charging. 2. Fully charged: The light shows green when in AC mode.

Chapter 1

TouchPad Basics (with fingerprint reader)

The following items show you how to use the TouchPad with Acer Bio-Protection fingerprint reader:

Move your finger across the TouchPad (1) to move the cursor. Press the left (2) and right (3) buttons located beneath the TouchPad to perform selection and execution functions. These two buttons are similar to the left and right buttons on a mouse. Tapping on the TouchPad is the same as clicking the left button. Left Button (2) Quickly click twice. Right Button (3) Main TouchPad (2) Tap twice (at the same speed as double-clicking a mouse button). Tap once. Tap twice (at the same speed as double-clicking a mouse button); rest your finger on the TouchPad on the second tap and drag the cursor. Click once.

Function Execute

Select Drag

Click once. Click and hold, then use finger on the TouchPad to drag the cursor.

Access context menu

NOTE: When using the TouchPad, keep it - and your fingers - dry and clean. The TouchPad is sensitive to finger movement; hence, the lighter the touch, the better the response. Tapping too hard will not increase the TouchPads responsiveness.

10

Chapter 1

Using the Keyboard

The keyboard has full-sized keys and an embedded numeric keypad, separate cursor, lock, Windows, function and special keys.

Lock Keys and embedded numeric keypad

The keyboard has three lock keys which you can toggle on and off.

Lock key Caps Lock Num Lock <Fn> + <F11>

Description When Caps Lock is on, all alphabetic characters typed are in uppercase. When Num Lock is on, the embedded keypad is in numeric mode. The keys function as a calculator (complete with the arithmetic operators +, -, *, and /). Use this mode when you need to do a lot of numeric data entry. A better solution would be to connect an external keypad. When Scroll Lock is on, the screen moves one line up or down when you press the up or down arrow keys respectively. Scroll Lock does not work with some applications.

Scroll Lock <Fn> + <F12>

The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols are not printed on the keys.

Desired access Number keys on embedded keypad Cursor-control keys on embedded keypad Main keyboard keys

Num Lock on Type numbers in a normal manner. Hold <Shift> while using cursorcontrol keys. Hold <Fn> while typing letters on embedded keypad.

Num Lock off

Hold <Fn> while using cursorcontrol keys. Type the letters in a normal manner.

Chapter 1

11

Windows Keys
The keyboard has two keys that perform Windows-specific functions. Key Description

Windows key Pressed alone, this key has the same effect as clicking on the Windows Start button; it launches the Start menu. It can also be used with other keys to provide a variety of functions:
< < < < < < >: > > > > >

Open or close the Start menu

+ <D>: Display the desktop + <E>: Open Windows Explore + <F>: Search for a file or folder + <G>: Cycle through Sidebar gadgets + <L>: Lock your computer (if you are connected to a network domain), or switch users (if you're not connected to a network domain) + <M>: Minimizes all windows + <R>: Open the Run dialog box + <T>: Cycle through programs on the taskbar + <U>: Open Ease of Access Center + <X>: Open Windows Mobility Center + <BREAK>: Display the System Properties dialog box + <SHIFT+M>: Restore minimized windows to the desktop + <TAB>: Cycle through programs on the taskbar by using Windows Flip 3-D + <SPACEBAR>: Bring all gadgets to the front and select Windows Sidebar
> >

< < < < < < < < <

> > > > > > > > >

<CTRL> + < <CTRL> + <

+ <F>: Search for computers (if you are on a network)

+ <TAB>: Use the arrow keys to cycle through programs on the taskbar by using Windows Flip 3-D Note: Depending on your edition of Windows Vista, some shortcuts may not function as described. This key has the same effect as clicking the right mouse button; it opens the application's context menu.

Application key

12

Chapter 1

Hot Keys
The computer employs hotkeys or key combinations to access most of the computers controls like screen brightness, volume output and the BIOS utility. To activate hot keys, press and hold the <Fn> key before pressing the other key in the hotkey combination.

Hotkey <Fn> + <F1> <Fn> + <F2> <Fn> + <F3> <Fn> + <F4> <Fn> + <F5>

Icon

Function Hotkey help Acer eSettings Management Acer ePower Management Sleep Display toggle

Description Displays help on hotkeys. Launches Acer eSettings Management in Acer Empowering Technology. Launches Acer ePower Management in Acer Empowering Technology. Puts the computer in Sleep mode. Switches display output between the display screen, external monitor (if connected) and both. Turns the display screen backlight off to save power. Press any key to return. Turns the internal TouchPad on and off. Turns the speakers on and off. Increases the screen brightness. Decreases the screen brightness.

<Fn> + <F6> <Fn> + <F7> <Fn> + <F8> <Fn> + < > <Fn> + < >

Screen blank TouchPad toggle Speaker toggle Brightness up Brightness down

Chapter 1

13

Special Key
You can locate the Euro symbol and the US dollar sign at the upper-center and/or bottom-right of your keyboard.

The Euro symbol

1. Open a text editor or word processor. 2. Hold <Alt Gr> and then press the <5> key at the upper-center of the keyboard. NOTE: Note: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/ typography/faq/faq12.htm for more information.

The US dollar sign

1. Open a text editor or word processor. 2. Hold <Shift> and then press the <4> key at the upper-center of the keyboard. NOTE: This function varies by the operating system version.

14

Chapter 1

Using the System Utilities

Acer GridVista (dual-display compatible)
NOTE: This feature is only available on certain models. To enable the dual monitor feature of the notebook, first ensure that the second monitor is connected, then select Start, Control Panel, Display and click on Settings. Select the secondary monitor (2) icon in the display box and then click the check box Extend my windows desktop onto this monitor. Finally, click Apply to confirm the new settings and click OK to complete the process.

Acer GridVista is a handy utility that offers four pre-defined display settings so you can view multiple windows on the same screen. To access this function, please go to Start All Programs and click on Acer GridVista. You may choose any one of the four display settings indicated below:

Double (vertical), Triple (primary at left), Triple (primary at right), or Quad Acer Gridvista is dual-display compatible, allowing two displays to be partitioned independently. Acer Gridvista is dual-display compatible, allowing two displays to be partitioned independently. AcerGridVista is simple to set up: 1. 2. 3. Run Acer GridVista and select your preferred screen configuration for each display from the task bar. Drag and drop each window into the appropriate grid. Enjoy the convenience of a well-organized desktop.

NOTE: Please ensure that the resolution setting of the second monitor is set to the manufacturer's recommended value.

Chapter 1

15

Hardware Specifications and Configurations

Processor Item CPU type Core logic Specification Penryn based Intel Celeron Processor and Intel Pentium Processor Intel Cantiga GL40 (667MHz FSB supported) ICH9-M ENE KB926 for Keyboard Controller, Battery management Unit. Integrated VGA solution for CANTIGA GL40 REALTEK ALC268 for High Definition Audio Codec. REALTEK RTL8111C-GR for Giga LAN Micro uPGA-478

CPU package CPU Fan True Value Table CPU Temperature Core 0 50 60 70 77 85

Core 1 50 60 70 77 85

Fan Speed (rpm) 3000 3400 3700 4000 4000 31 34 37 40 40

SPL Spec (dBA)

Throttling 50%: On= 85C; OFF=78C OS shut down at 90C; H/W shut down at 96C Item Specification Insyde V0.15T2 Flash 1 MB

BIOS

BIOS vendor BIOS Version BIOS ROM type BIOS ROM size Supported protocols

Flash ROM 1MB Support multi-boot Suspend to RAM (S3)/Disk (S4) Various hot-keys for system control Support SMBUS 2.0, PCI2.3 ACPI 2.0 compliance with Intel Speed Step Support C1, C2, C3 and S3, S4 for mobile CPU DMI utility for BIOS serial number configurable/asset tag Support PXE Support Y2K solution Support Win Flash Wake on LAN from S3 Wake on LAN form S4 in AC mode System information

BIOS password control

BIOS user, Supervisor and HDD passwords

16

Chapter 1

System Memory Item Memory controller Memory size DIMM socket number Supports memory size per socket Supports maximum memory size Supports DIMM type Supports DIMM Speed Supports DIMM voltage Supports DIMM package Memory Combinations Slot 1 0MB 0MB 0MB 512MB 512MB 512MB 1024MB 1024MB 1024MB 1024MB 2048MB 2048MB 2048MB 2048MB 512MB 1024MB 2048MB 512MB 1024MB 2048MB 0MB 512MB 1024MB 2048MB 0MB 512MB 1024MB 2048MB Slot 2 512MB 1024MB 2048MB 1024MB 1536MB 2560MB 1024MB 1536MB 2048MB 3072MB 2048MB 2560MB 3072MB 4096MB Total Memory Built-in 0MB (no on-board memory) 2 sockets 2 GB 4G for 64bit OS (with two 2GB SODIMM) DDR 2 Synchronous DRAM 667 MHz 1.8V 200-pin soDIMM Specification

NOTE: Above table lists some system memory configurations. You may combine DIMMs with various capacities to form other combinations. On above table, the configuration of slot 1 and slot 2 could be reversed. LAN Interface Item LAN Chipset Supports LAN protocol LAN connector type LAN connector location Features Wireless Module 802.11b/g Item Chipset Data throughput Protocol Interface Specification Specification REALTEK RTL8111C-GR for GIGA LAN PCI-E 10/100/1000 MB LAN RJ-45 Left side Support Wake-On-Lan (AC mode S5)

Chapter 1

17

Hard Disk Drive Interface Item Vendor Model Name Capacity (MB) Bytes per sector Data heads Drive Format Disks Spindle speed (RPM) Performance Specifications Buffer size Interface Internal transfer rate (Mbits/ sec max) Sustained transfer rate (Mbytes/sec max) I/O data transfer rate (Mbytes/sec max) DC Power Requirements Voltage tolerance 5V(DC) +/- 5% 8MB SATA 778 58 300 2 2 5,400 1 4 3 ST9250827AS 250 Specification Seagate Momentus 5400.4 SATA ST9160827AS 160 512 2 ST9120817AS 120

Item Vendor Model Name Capacity (MB) Bytes per sector Data heads Drive Format Disks Spindle speed (RPM) Performance Specifications Buffer size Interface Internal transfer rate (Mbits/sec max) I/O data transfer rate (Mbytes/sec max) DC Power Requirements Voltage tolerance 2 or 1 2 4 4 or 3 ST9320320AS 320

Specification Seagate Momentus 5400.5 SATA ST9250320AS 250 ST9160310AS 160 512 2 1 5,400 8 MB SATA 352 150 2 1 ST9120310AS 120

5V(DC) +/- 5%

18

Chapter 1

Super-Multi Drive Module Item Vendor & model name Performance Specification Transfer rate (MB/sec) Buffer Memory Interface Applicable disc format With CD Diskette Sustained: Max 3.5 Mbytes/sec 2MB SATA Applicable media types: Writing: Confirms to DVD+R Version 1.2 and DVD+RW Version 1.3 / DVD+R DL Version 1.0 /DVD-R Version 2.0 / DVD-RW Version 1.2 / DVD-R DL Version 3.0. Reading: DVD single/dual layer (PTP, OTP), DVD-R single/dual layer DVD+R single/double layer DVD-RW DVD+RW CD-DA CD-ROM CD-ROM/XA Photo-CD, Multi-session, Video CD CD-I FMV, CD Extra, CD Plus, CD-R, and CD-RW Drawer (Solenoid Open) Tact SW (Open) Emergency Release (draw open hole) DC 5 V +/- 5% Specification HLDS/GSA-T50N, Philips DS-8A2S, Sony/AD-7560S, Toshiba Digi/TS-L633A With DVD Diskette Sustained: Max 10 Mbytes/sec

Loading mechanism

Power Requirement Input Voltage Audio Interface Item Audio Controller Mono or Stereo Compatibility Stereo MIC INAC-coupled input,100mVP-P maximum LINE INAC-coupled input,100mVP-P maximum Headphone out1VP-P Build-in Speaker4 ohm, 2W Main Speaker System Board Major Chips Item Core logic LAN Audio Codec Keyboard Item Keyboard controller Total number of keypads KB926 88-/89-key keyboard Specification Controller Intel Core2 Duo processor based Intel Celeron processor and Intel Pentium processor, FSB 667MHz REALTEK RTL8111C-GR for GIGA LAN REALTEK ALC268 for High Definition Audio Codec Specification REALTEK ALC268 for High Definition Audio Codec

Chapter 1

19

Item Windows logo key Internal & external keyboard work simultaneously Battery Item Vendor & model name Battery Type Pack capacity Number of battery cell Package configuration LCD 14.1 Item Vendor/model name Screen Diagonal (mm) Active Area (mm) Display resolution (pixels) Pixel Pitch Pixel Arrangement Display Mode Typical White Luminance (cd/m also called Brightness Luminance Uniformity Contrast Ratio Response Time (Optical Rise Time/Fall Time) msec Nominal Input Voltage VDD Typical Power Consumption (watt) Weight (without inverter) Physical Size (mm) Electrical Interface Support Color Viewing Angle (degree) Horizontal: Right/Left Vertical: Upper/Lower Temperature Range (C) Operating Storage (shipping)
2)

Specification Yes Yes

Specification Sanyo, Sony, Panasonic, Simplo Li Ion 2400/4400 mAh 6 3S2P

Specification LG.Philips/LP141WX3, AUO/B141EW04 V4, Chimei/N141I3 - L02, Samsung/LTN141W3-L01 14.1 inches 303.74 x 189.84 mm 1280 x 800 WXGA 0.2373 0.2373 mm R.G.B. Vertical Stripe Transmissive mode, normally white 200 cd/m2(Typ.5 point) 1.3 max. 300 minimum 16 +3.3V 1.4W max. 400g max. 319.5 (0.5) x 205.5 ( 0.5) x 5.5 max. 3.3V LVDS interface with 1 pixel/clock greater than 262144 Minimum: 40/40, Typical: 45/45 Minimum: 10/30, Typical: 20/35 0 to +50 -20 to +60

20

Chapter 1

Chapter 2

System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computers BIOS (Basic Input/ Output System). Your computer is already properly configured and optimized, and you do not need to run this utility. However, if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 Troubleshooting when problem arises. To activate the BIOS Utility, press F2 during POST (when Press <F2> to enter Setup message is prompted on the bottom of screen). Press F2 to enter setup. The default parameter of F12 Boot Menu is set to disabled. If you want to change boot device without entering BIOS Setup Utility, please set the parameter to enabled. Press <F12> during POST to enter multi-boot menu. In this menu, user can change boot device without entering BIOS SETUP Utility.

Navigating the BIOS Utility

There are six menu options: Information, Main, Advanced, Security, Boot, and Exit. Follow these instructions:

To choose a menu, use the left and right arrow keys. To choose an item, use the up and down arrow keys. To change the value of a parameter, press F5 or F6. A plus sign (+) indicates the item has sub-items. Press Enter to expand this item. Press Esc while you are in any of the menu options to go to the Exit menu.

In any menu, you can load default settings by pressing F9. You can also press F10 to save any changes made and exit the BIOS Setup Utility. NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a particular menu are shown on the bottom of the screen. Help for parameters are found in the Item Specific Help part of the screen. Read this carefully when making changes to parameter values. Please note that system information is subject to different models.

Chapter 2

21

Information
The Information screen displays a summary of your computer hardware information.

Information CPU Type: CPU Speed:

Main

InsydeH20 Setup Utility Advanced Security Power

Rev. 3.5 Boot Exit

Intel (R) Core (TM)2 Duo CPU @ 2.40GHz 2.40GHz Hitachi HTS543516K9SA00 071129BB0C02WGHDKKGC Slimtype DVD A DS8A2S V0.15T2 Intel V1588

HDD Model Name: HDD Serial Number: ATAPI Model Name: System BIOS Version: VGA BIOS Version: Serial Number: Asset Tag Number: Product Name: Manufacturer Name: UUID:

Aspire 4930 Acer 864BD4BE-6B22-5843-38D2-001B38D637FC

F1 Help ESC Exit

Select Item Select Menu

F5/F6 Change Item F9 Setup Default Enter Select Submenu F10 Save and Exit

NOTE: The system information is subject to different models. Parameter CPU Type CPU Speed HDD Model Name HDD Serial Number ATAPI Model Name System BIOS Version VGA BIOS Version Serial Number Asset Tag Number Product Name Manufacturer Name UUID Number Description This field shows the CPU type and speed of the system. This field shows the speed of the CPU. This field shows the model name of HDD installed on primary IDE master. This field displays the serial number of HDD installed on primary IDE master. This field shows the model name of the Optical device installed in the system. Displays system BIOS version. This field displays the VGA firmware version of the system. This field displays the serial number of this unit. This field displays the asset tag number of the system. This field shows product name of the system. This field displays the manufacturer of this system. Universally Unique Identifier (UUID) is an identifier standard used in software construction, standardized by the Open Software Foundation (OSF) as part of the Distributed Computing Environment (DCE).

22

Chapter 2

Main
The Main screen allows the user to set the system time and date as well as enable and disable boot option and recovery.

Information System Time System Date Total Memory Video Memory

Main

InsydeH20 Setup Utility Advanced Security Power [13:04:04] [04/21/2008] 3017 MB [32MB] [Enabled] [Enabled] [Disabled] [Enabled] [ACHI]

Boot

Rev. 3.5 Exit Item Specific Help This is the help for the hour field. Valid range is from 0 to 23. INCREASE/REDUCE : F5/F6

Quick Boot Network Boot F12 Boot Menu D2D Recovery SATA Mode

F1 Help ESC Exit

Select Item Select Menu

F5/F6 Change Item F9 Setup Default Enter Select Submenu F10 Save and Exit

NOTE: The screen above is for your reference only. Actual values may differ. The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings. Parameter System Time System Date Total Memory Video Memory Quick Boot Network Boot F12 Boot Menu D2D Recovery Description Sets the system time. The hours are displayed with 24hour format. Sets the system date. This field reports the memory size of the system. Memory size is fixed to 3017 MB. Shows the video memory size. VGA Memory size=32 MB Allows startup to skip certain tests while booting, decreasing the time needed to boot the system. Enables, disables the system boot from LAN (remote server). Enables, disables Boot Menu during POST. Enables, disables D2D Recovery function. The function allows the user to create a hidden partition on hard disc drive to store operation system and restore the system to factory defaults. Control the mode in which the SATA controller should operate. Format/Option Format: HH:MM:SS (hour:minute:second) Format MM/DD/YYYY (month/day/year) N/A N/A Option: Enabled or Disabled Option: Enabled or Disabled Option: Disabled or Enabled Option: Enabled or Disabled

SATA Mode

Option: AHCI Mode or IDE Mode

NOTE: The sub-items under each device will not be shown if the device control is set to disable or auto. This is because the user is not allowed to control the settings in these cases. Chapter 2 23

Advanced
The Advanced screen allows the user to configure the various advanced BIOS options. IMPORTANT:Making incorrect settings to items on these pages may cause the system to malfunction. Unless you have experience adjusting these items, we recommend that you leave these settings at the default values. If making settings to items on these pages causes your system to malfunction or prevents the system from booting, open BIOS and choose Load Optimal Defaults in the Exit menu to boot up normally.

Information

Main

InsydeH20 Setup Utility Advanced Security Power

Rev. 3.5 Boot Exit Item Specific Help Configures Boot Settings.

Boot Configuration Peripheral Configuration IDE Configuration Video Configuration USB Configuration Chipset Configuration ACPI Table/Features Control Express Card PCI Express Root Port 1 PCI Express Root Port 2 PCI Express Root Port 3 PCI Express Root Port 4 PCI Express Root Port 5 PCI Express Root Port 6 ASF Configuration F1 Help ESC Exit
Select Item Select Menu

[Disabled]

F5/F6 Change Item F9 Setup Default Enter Select Submenu F10 Save and Exit

The table below describes the items, menus, and submenus in this screen. Settings in boldface are the default and suggested parameter settings. Parameter Boot Configuration Peripheral Configuration Description Enter the Boot Configuration menu. Enter the Peripheral Configuration menu. Submenu Items Numlock Zip Emulation Type Serial Port A Infrared Port Azalia LAN IDE Controller HDC Configure as ACHI Option ROM Support SATA Port 0, 1, 4, and 5 Hotplug Channel 1 to 4 Master and Slave IGD Device2, Function1 IGD Pre-allocate Memory IGD DVMT Size Clock Chip Intialize Enabled CK SSC IGD Boot Type IGD LCD Panel Type IGD TV Chapter 2

IDE Configuration

Enter the IDE Configuration menu.

Video Configuration

Enter the Video Configuration menu.

24

Parameter USB Configuration

Description Enter the USB Configuration menu.

Submenu Items USB Driver Select EHCI 1 and 2 UHCI 1 to 5 Per-Port Control Port 80h Cycles DMI Link ASPM Control PCI Latency Timer VT-d FACP C2 Latency Value FACP C3 Latency Value FACP RTC S4 Wakeup APIC IO APIC Mode HPET Support Base Address Select

Chipset Configuration

Enter the Chipset Configuration menu.

ACPI Table/ Features Control

Enter the ACPI Table/Features Control menu.

Express Card

Disable or Enable the Express Card solution for windows Standby and Hibernation. Enter the PCI Port 1 to 6 configuration menus.

N/A

PCI Express Root Port 1 to 6

VC1 Enable ASPM URR FER NFER CER CTO SEFE SENFE SECE PME Interrupt PME SCI Hot Plug SCI Mini Watchdog Timeout BIOS Boot Timeout OS Boot Timeout Power-on wait time

ASF Configuration

Enter the ASF Configuration menu.

Chapter 2

25

Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized use.

Information

Main

InsydeH20 Setup Utility Advanced Security Power Clear Clear Clear [32MB]

Boot

Supervisor Password Is: User Password Is: HDD Password Is: Set Supervisor Password Set User Password Set Hdd Password Power on password

Rev. 3.5 Exit Item Specific Help Install or Change the password and the length of password must be less than eight words.

[Enabled]

F1 Help ESC Exit

Select Item Select Menu

F5/F6 Change Item F9 Setup Default Enter Select Submenu F10 Save and Exit

The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings. Parameter Supervisor Password Is User Password Is HDD Password Is Set Supervisor Password Description Shows the setting of the Supervisor password Shows the setting of the user password. Shows the setting of the hard disk password. Press Enter to set the supervisor password. When set, this password protects the BIOS Setup Utility from unauthorized access. The user can not either enter the Setup menu nor change the value of parameters. Press Enter to set the user password. When user password is set, this password protects the BIOS Setup Utility from unauthorized access. The user can enter Setup menu only and does not have right to change the value of parameters. Enter HDD Password. Defines whether a password is required or not while the events defined in this group happened. The following sub-options are all requires the Supervisor password for changes and should be grayed out if the user password was used to enter setup. Disabled or Enabled Option Clear or Set Clear or Set Clear or Set

Set User Password

Set HDD Password Password on Boot

NOTE: When you are prompted to enter a password, you have three tries before the system halts. Dont forget your password. If you forget your password, you may have to return your notebook computer to your dealer to reset it.

26

Chapter 2

Setting a Password
Follow these steps as you set the user or the supervisor password: 1. Use the and keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Supervisor Password box appears:

2.

Type a password in the Enter New Password field. The password length can not exceeds 8 alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the Confirm New Password field.

IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen. 3. 4. 5. Press Enter. After setting the password, the computer sets the User Password parameter to Set. If desired, you can opt to enable the Password on boot parameter. When you are done, press F10 to save the changes and exit the BIOS Setup Utility.

Removing a Password
Follow these steps: 1. Use the and keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Password box appears:

2. 3. 4.

Type the current password in the Enter Current Password field and press Enter. Press Enter twice without typing anything in the Enter New Password and Confirm New Password fields. The computer then sets the Supervisor Password parameter to Clear. When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.

Chapter 2

27

Changing a Password
1. Use the and keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Password box appears.

2. 3. 4. 5. 6.

Type the current password in the Enter Current Password field and press Enter. Type a password in the Enter New Password field. Retype the password in the Confirm New Password field. Press Enter. After setting the password, the computer sets the User Password parameter to Set. If desired, you can enable the Password on boot parameter. When you are done, press F10 to save the changes and exit the BIOS Setup Utility.

If the verification is OK, the screen will display as following.

The password setting is complete after the user presses Enter. If the current password entered does not match the actual current password, the screen will show you the Setup Warning.

If the new password and confirm new password strings do not match, the screen will display the following message.

28

Chapter 2

Power
The Power screen allows the user to configure various CPU and power management options and device wakeup behavior.

Information

Main

InsydeH20 Setup Utility Advanced Security Power

Boot

Advanced CPU Control Platform Power Management ACPI S3: Wake on PME Wake on Modem Ring Auto wake on S5 Quickly S4 Resume [Enabled] [Enabled] [Enabled] [Disabled] [Disabled]

Rev. 3.5 Exit Item Specific Help These items control various CPU parameters.

F1 Help ESC Exit

Select Item Select Menu

F5/F6 Change Item F9 Setup Default Enter Select Submenu F10 Save and Exit

The table below describes the items, menus, and submenus in this screen. Settings in boldface are the default and suggested parameter settings. Parameter Advanced CPU Control Description Enter the Advanced CPU Control menu. Submenu Items P-States (IST) Boot performance mode Thermal Mode CMP Support Use XD capability VT Support C-States Enhanced C-States C-State Pop Up Mode C-State Pop Down Mode C4 Exit Timing Mode DeepC4 Hard C4E Enable C6 EMTTM Bi-directional PROCHOT# Dynamic FSB Switching Turbo Mode ACPI 3.0 T-States DTS DTS Calibration Thermal Trip Points Setting (Fan On Temp., Throttle On Temp.)

Chapter 2

29

Parameter Platform Power management ACPI S3 Wake on PME

Description Enter the Platform Power Management menu. Enable or Disable ACPI S1/S3 Sleep State Enable or Disable wake up when the system power is off and a PCI Power Management Enable wake up event occurs. Enable or Disable wake up when the system power is off and a modem attached to the serial port is ringing. Disable or Enable auto wake up by date and time or at a fixed time everyday. Disable or Enable optional quick boot from S4 Resume.

Submenu Items PCI Clock Run _CST - C4 Latency Value C4 on C3 - Deeper Sleep

N/A N/A

Wake on Modem Ring Auto wake on S5 Quickly S4 Resume

N/A

N/A N/A

30

Chapter 2

Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices includes the USB diskette drives, the onboard hard disk drive and the DVD drive in the module bay.

Information

Main

InsydeH20 Setup Utility Advanced Security Power

Boot

Boot priority order: 1. IDE0 : Hitachi HTS542516K9SA00 2. IDE1 : Slimtype DVD A DS8A2S 3 . USB FDD : 4. Network Boot : Realtek Boot Agent 5. USB HDD : 6. USB CDROM :

Rev. 3.5 Exit Item Specific Help Use <> or <> to select a device, then press <F5> to move it down the list, or <F6> to move it up the list. Press <Esc> to escape the menu

F1 Help ESC Exit

Select Item Select Menu

F5/F6 Change Item F9 Setup Default Enter Select Submenu F10 Save and Exit

Chapter 2

31

Exit
The Exit screen allows you to save or discard any changes you made and quit the BIOS Utility.

Information

Main

InsydeH20 Setup Utility Advanced Security Power

Boot

Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes

Rev. 3.5 Exit Item Specific Help Exit System Setup and save your changes to CMOS.

F1 Help ESC Exit

Select Item Select Menu

F5/F6 Change Item F9 Setup Default Enter Select Submenu F10 Save and Exit

The table below describes the parameters in this screen. Parameter Exit Saving Changes Exit Discarding Changes Load Setup Default Discard Changes Save Changes Description Exit System Setup and save your changes to CMOS. Exit utility without saving setup data to CMOS. Load default values for all SETUP item. Load previous values from CMOS for all SETUP items. Save Setup Data to CMOS.

32

Chapter 2

BIOS Flash Utilities

The BIOS flash memory update is required for the following conditions:

New versions of system programs New features or options Restore a BIOS when it becomes corrupted.

Use the Phlash utility to update the system BIOS flash ROM. NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery Diskette before you use the Phlash utility. NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash. NOTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not completely loaded. Fellow the steps below to run the Phlash. 1. 2. 3. Prepare a bootable diskette. Copy the flash utilities to the bootable diskette. Then boot the system from the bootable diskette. The flash utility has auto-execution function.

Chapter 2

33

DOS Flash Utility

Perform the following steps to use the DOS Flash Utility: 1. 2. Press F2 during boot to enter the Setup Menu. Select Boot Menu to modify the boot priority order, for example, if using USB HDD to Update BIOS, move USB HDD to position 1.

Information

Main

InsydeH20 Setup Utility Advanced Security Power Boot

Boot priority order: 1. IDE0 : Hitachi HTS542516K9SA00 2. IDE1 : Slimtype DVD A DS8A2S 3 . USB FDD : 4. Network Boot : Realtek Boot Agent 5. USB HDD : ABC 6. USB CDROM :

Rev. 3.5 Exit Item Specific Help Use < > or < > to select a device, then press <F5> to move it down the list, or <F6> to move it up the list. Press <Esc> to escape the menu

F1 Help ESC Exit

3.

Select Item Select Menu

F5/F6 Change Item Enter Select Submenu

F9 Setup Default F10 Save and Exit

Execute the IFLASH.BAT batch file to update BIOS.

The flash process begins as shown.

34

Chapter 2

4. In flash BIOS, the message Please do not remove AC Power Source displays. NOTE: If the AC power is not connected, the following message displays.

Plug in the AC power to continue. 5. Flash is complete when the message Flash programming complete displays.

Chapter 2

35

WinFlash Utility
Perform the following steps to use the WinFlash Utility: 1. 2. Double click the WinFlash executable. Click OK to begin the update. A progress screen displays.

3.

When the process is complete, close all programs and applications and reboot the system.

36

Chapter 2

Remove HDD/BIOS Password Utilities

This section provide you with removing HDD/BIOS method: Remove HDD Password: When the user keys in the wrong password three times, the system reports the following error code to user.

To unlock the HDD password, perform the following steps: 1. Press Enter to display the Select Item screen.

2.

Select Enter Unlock Password and press Enter.

An Unlock Password displays.

3. 4. 5. 6. 7.

Make a note of the key, 76943488 in the example. Boot up the system and open a DOS prompt. Enter the UnlockHD.EXE command and input the key to create an unlock code. Make a note of the result, for example 46548274. Reboot and enter the BIOS by pressing F2 when prompted. Go to the Security menu and select Set Hdd Password (see Security on page 26).

8. 9.

Enter the unlock code generated by UnlockHD.EXE as the current password, 46548274 in the example, and complete the New Password and Confirm fields to create a new HDD password. Save and exit the BIOS to complete the process.

Chapter 2

37

Removing BIOS Passwords: If you key in the wrong Supervisor Password three times, System Disabled displays on the screen. See the image below.

To reset the BIOS password, run BIOS_PW.EXE as follows: 1. Key in bios_pw 14452 0 2. Select one string from the list.

38

Chapter 2

3. Reboot the system and key in the selected string (qjjg9vy, 07yqmjd etc.) for the BIOS user

password.

Cleaning BIOS Passwords To clear the password, perform the following steps: 1. From a DOS prompt, Execute clnpwd.exe

2.

Press 1 or 2 to clean the desired password shown on the screen.

The onscreen message determines whether the function is successful or not.

Chapter 2

39

40

Chapter 2

Chapter 3

Machine Disassembly and Replacement

IMPORTANT:The outside housing and color may vary from the mass produced model. This chapter contains step-by-step procedures on how to disassemble the notebook computer for maintenance and troubleshooting.

Disassembly Requirements
To disassemble the computer, you need the following tools:

Wrist grounding strap and conductive mat for preventing electrostatic discharge Flat screwdriver Philips screwdriver Plastic flat screwdriver

Plastic tweezers NOTE: The screws for the different components vary in size. During the disassembly process, group the screws with the corresponding components to avoid mismatch when putting back the components.

IMPORTANT:Various images depict the use of a regular metal screwdriver, however, a plastic screwdriver is advised when disassembling parts near or around the motherboard and to prevent scratching of the computer surface.

Chapter 3

41

General Information
Pre-disassembly Instructions
Before proceeding with the disassembly procedure, make sure that you do the following: 1. Turn off the power to the system and all peripherals. 2. Unplug the AC adapter and all power and signal cables from the system.

3. Place the system on a flat, stable surface. 4. Remove the battery pack.

Disassembly Process
The disassembly process is divided into the following stages:

External module disassembly Main unit disassembly LCD module disassembly

The flowcharts provided in the succeeding disassembly sections illustrate the entire disassembly sequence. Observe the order of the sequence to avoid damage to any of the hardware components. For example, if you want to remove the main board, you must first remove the keyboard, then disassemble the inside assembly frame in that order. Main Screw List Screw M2.5*8 M2.5*5 M2*L3 M2.5*4 M3*3 M2.5*6.5 Quantity 15 21 22 3 4 4 Part Number 86.AT902.001 86.AT902.002 86.AT902.003 86.AT902.004 86.AT902.006 86.AT902.007

42

Chapter 3

External Module Disassembly Process

IMPORTANT:The outside housing and color may vary from the mass produced model.

External Modules Disassembly Flowchart

The flowchart below gives you a graphic representation on the entire disassembly sequence and instructs you on the components that need to be removed during servicing. For example, if you want to remove the main board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.
Turn off system and peripherals power

Disconnect power and signal cables from system

Remove Battery

Remove Lower Covers

Remove DIMMs

Remove WLAN

Remove HDD

Remove ODD

Remove Antenna

Screw List Step Memory Cover WLAN Cover WLAN Module HDD Carrier ODD Module ODD Bracket Screw M2.5*8 M2.5*8 M2*L3 M3*3 M2.5*5 M2*L3 2 1 2 4 1 3 Quantity Part No. 86.AT902.001 86.AT902.001 86.AT902.003 86.AT902.006 86.AT902.002 86.AT902.003

Chapter 3

43

Removing the Battery Pack

1. Turn computer over. 2. Slide the battery lock/unlock latch to the unlock position.

3. Slide and hold the battery release latch to the release position (1), then slide out the battery pack from the main unit (2).

2 1

44

Chapter 3

Removing the Lower Covers

1. See Removing the Battery Pack on page 44. 2. Remove the three screws from the memory and WLAN bays and loosen the two captive screws on the HDD cover.

Memory Cover

WLAN Cover

HDD Cover

Step Memory Cover M2.5*8

Size 2

Quantity

Screw Type

WLAN Cover

M2.5*8

3. Carefully open the memory cover.

4. Remove the HDD cover as shown.

Chapter 3

45

5. Remove the WLAN cover as shown.

46

Chapter 3

Removing the DIMM Modules

1. See Removing the Battery Pack on page 44. 2. Remove the Memory Module cover See Removing the Lower Covers on page 45. 3. Push out the release latches on both sides of the DIMM socket to release the DIMM module.

4. Remove the DIMM module.

5. Repeat steps for the second DIMM module if present.

Chapter 3

47

Removing the WLAN Module

1. See Removing the Battery Pack on page 44. 2. Remove the WLAN cover. See Removing the Lower Covers on page 45. 3. Disconnect the antenna cables from the WLAN board.

4. Move the antenna away and remove the two screws on the WLAN board to release the WLAN board.

Step WLAN Module M2*L3

Size 2

Quantity

Screw Type

5. Detach the WLAN board from the WLAN socket.

48

Chapter 3

NOTE: When attaching the antenna back to the WLAN board, make sure the cables are sitting in the housing to prevent damage.

Chapter 3

49

Removing the Hard Disk Drive Module

1. See Removing the Battery Pack on page 44. 2. Remove the HDD cover, See Removing the Lower Covers on page 45. 3. Use the pull-tab to pull and lift the hard disk drive module out of the bay.

NOTE: To prevent damage to device, avoid pressing down on it or placing heavy objects on top of it. 4. Remove the four screws securing the hard disk to the carrier.

50

Chapter 3

Step HDD Carrier M3*3

Size 4

Quantity

Screw Type

5. Remove the HDD from the carrier.

Chapter 3

51

Removing the Optical Drive Module

1. See Removing the Battery Pack on page 44. 2. Remove the Memory cover. See Removing the Lower Covers on page 45. 3. Remove the screw securing the ODD module.

Step ODD Module M2.5*5

Size 1

Quantity

Screw Type

4. Pull the optical drive module out from the chassis.

52

Chapter 3

5. Remove the three screws securing the ODD bracket and remove the ODD bracket from the optical disk drive module.

Step ODD Bracket M2*L3

Size 3

Quantity

Screw Type

6. Insert a pin in the eject hole of the ODD to eject the ODD tray.

7. Press down on the locking catch to release the ODD cover and remove.

Chapter 3

53

Main Unit Disassembly Process

IMPORTANT:The outside housing and color may vary from the mass produced model.

Main Unit Disassembly Flowchart

Remove External Modules before proceeding Remove Switch Cover Remove Keyboard

Remove Antenna

Remove LCD Module

Remove Upper Case

Remove Lower Case

Remove TouchPad Bracket

Remove Speaker Module

Remove Power Board

Remove Modem Module

Remove Mainboard

Remove CPU Fan

Remove Thermal Module

Remove CPU

Screw List Step Switch Cover LCD Module Screw M2.5*5 M2.5*8 M2.5*8 M2.5*5 Upper Cover TouchPad Bracket Speaker Module Modem Module Mainboard CPU Fan Thermal Module 54 M2.5*8 M2.5*5 M2*L3 M2*L3 M2*L3 M2.5*5 M2.5*4 M2.5*6.5 3 2 2 2 8 7 2 4 2 1 3 4 Quantity Part No. 86.AT902.002 86.AT902.001 86.AT902.001 86.AT902.002 86.AT902.001 86.AT902.002 86.AT902.003 86.AT902.003 86.AT902.003 86.AT902.002 86.AT902.004 86.AT902.007 Chapter 3

Removing the Switch Cover

CAUTION: Using tools to remove the Switch Cover may cause damage to the outer casing. It is recommended that you only use your fingers to remove the Switch Cover. 1. See Removing the Battery Pack on page 44. 2. Locate and remove the three securing screws from the battery bay.

Step Switch Cover M2.5*5

Size 3

Quantity

Screw Type

3. Turn the computer over and open the LCD module to expose the Switch Cover. 4. Lift the Switch Cover as shown, and move from right to left side.

5. Lift the Switch Cover clear of the chassis.

Chapter 3

55

56

Chapter 3

Removing the Keyboard

1. See Removing the Switch Cover on page 55. 2. Lift the keyboard away from the chassis as shown.

3. Turn the keyboard over on the TouchPad area to expose the FFC cable.

4. Open the cable retainer and disconnect the FFC cable from the mainboard.

5. Lift the keyboard clear of the chassis.

Chapter 3

57

Removing the Antenna

1. See See Removing the Keyboard on page 57. 2. Remove the Antenna Cables from the securing pins as shown.

3. Turn the computer over. Remove the adhesive strip holding the antenna cables.

4. Feed the antenna cables from the underside of the computer.

58

Chapter 3

5. Remove the Antenna Cables from the securing pins as shown.

Chapter 3

59

Removing the LCD Module

1. See Removing the Battery Pack on page 44. 2. See Removing the Antenna on page 58. 3. Remove the two securing screws from the bottom of the chassis.

Step LCD Module M2.5*8

Size 2

Quantity

Screw Type

4. Turn the computer over. Peel back the protective film to expose the interface cables.

5. Disconnect the two LCD interface cables from the chassis.

60

Chapter 3

6. Remove the four securing screws (two each side) from the LCD module.

Step LCD Module (red callout) M2.5*8

Size 2

Quantity

Screw Type

LCD Module (blue callout)

M2.5*5

7. Carefully remove the LCD module from the chassis.

Chapter 3

61

Removing the Upper Cover

1. See Removing the Battery Pack on page 44. 2. See Removing the Lower Covers on page 45. 3. See Removing the LCD Module on page 60. 4. Turn the computer over. Remove the eight screws on the bottom panel.

Step Upper Cover M2.5*8

Size 8

Quantity

Screw Type

5. Turn the computer over. Remove the seven screws on the top panel.

Step Upper Cover M2.5*5

Size 7

Quantity

Screw Type

62

Chapter 3

6. Disconnect the three cables from the mainboard as shown. B A

C Remove the adhesive tape to expose cable A. Disconnect A as shown.

Release the securing latches and disconnect B as shown.

Release the securing latches and disconnect C as shown.

NOTE: Avoid pulling on the cables directly to prevent damage to the connectors. NOTE: Use the pull-tabs on the FFC cables whenever available to prevent damage to the FFC cables.

Chapter 3

63

7. Remove the upper cover by lifting upward from the chassis, rear edge first.

8. Turn the upper cover over. The upper cover appears as follows.

64

Chapter 3

Removing the TouchPad Bracket

1. See Removing the Upper Cover on page 62. 2. Lift the cable latch and disconnect the TouchPad cable from the TouchPad board.

3. Remove the two securing screws from the TouchPad bracket.

Step TouchPad Bracket M2*L3

Size 2

Quantity

Screw Type

4. Push the TouchPad bracket to the left to clear the securing clip.

Chapter 3

65

5. Lift the rear edge of the TouchPad bracket first to clear the securing clips and remove the it as shown.

IMPORTANT:The TouchPad board is integrated into the design of the Upper Cover. To replace the TouchPad board, remove all components from the Upper Cover and install an entirely new Upper Cover. IMPORTANT:The MOSFET pad is attached to the Upper Cover and is reusable. If the replacement Upper Cover does not have a MOSFET pad (see highlighted area below), remove the MOSFET pad from the replaced Upper Cover and stick it to the new Upper Cover.

66

Chapter 3

Removing the Speaker Modules

1. See Removing the Upper Cover on page 62. 2. Remove the adhesive tape (blue callouts) and four securing screws (red callouts) from the speaker modules.

Step Speaker Modules (red callout) M2*L3

Size 4

Quantity

Screw Type

3. Peel back the Power Board FFC cable to expose the speaker cable.

4. Remove the speaker cable from the cable guides as shown.

Chapter 3

67

5. Remove the Speaker Modules from the upper cover.

68

Chapter 3

Removing the Power Board

1. See Removing the Upper Cover on page 62. 2. Remove the adhesive tape from the Power Board cable as shown.

3. Turn the Upper Cover over. Remove the adhesive tape from the Power Board as shown.

4. Lift the Power Board away from the cover and pull the FFC cable through as shown.

Chapter 3

69

Removing the Modem Module

1. See Removing the Upper Cover on page 62. 2. Remove the two screws securing the Modem module.

Step Modem Module M2*L3

Size 2

Quantity

Screw Type

3. Remove the Modem module from the Lower Cover.

4. Disconnect the Modem cable from the Modem module.

70

Chapter 3

Removing the Main Board

1. See Removing the Upper Cover on page 62. 2. Remove the securing screw from the Mainboard.

Step Mainboard M2.5*5

Size 1

Quantity

Screw Type

3. Remove the main board, rightside first, as shown. IMPORTANT:The DC IN cable is still attached to the mainboard at this stage. Do not remove the mainboard from the chassis completely.

4. Turn the Mainboard over to expose the DC IN connector.

Chapter 3

71

5. Disconnect the DC IN Cable from the mainboard.

6. Remove the mainboard from the chassis and place it on a clean, dust-free surface.

72

Chapter 3

Removing the CPU Fan

1. See Removing the Main Board on page 71. 2. Disconnect the fan cable from the mainboard.

3. Remove the three securing screws from the fan module.

Step Mainboard M2.5*4

Size 3

Quantity

Screw Type

4. Lift the fan clear of the mainboard.

Chapter 3

73

Removing the Thermal Module

1. See Removing the CPU Fan on page 73. 2. Remove the four securing screws (in reverse numerical order from screw 4 to screw 1) from the Thermal Module.

3 1

2 4

Step Thermal Module

Size M2.5*6.5 4

Quantity

Screw Type

3. Using both hands, lift the Thermal Module clear of the Mainboard.

74

Chapter 3

Removing the CPU

1. See Removing the Main Board on page 71. 2. See Removing the Thermal Module on page 74. 3. Using a flat screwdriver, turn the CPU socket latch counter-clockwise 180 to release the CPU.

k 4. Lift the CPU clear of the Mainboard.

Chapter 3

75

LCD Module Disassembly Process

IMPORTANT:The outside housing and color may vary from the mass produced model.

LCD Module Disassembly Flowchart

Remove LCD Panel from Main Unit before proceeding

Remove LCD Bezel

Remove Inverter Board

Remove LCD Panel

Remove Camera Module

Remove LCD FPC Cable

Remove LCD Brackets

Remove Antennas

Remove MIC Cable

Screw List Step LCD Bezel Inverter Board Camera Module LCD Panel LCD Brackets Screw M2.5*5 M2.5*5 M2*L3 M2.5*5 M2*L3 4 1 1 2 8 Quantity Part No. 86.AT902.002 86.AT902.002 86.AT902.003 86.AT902.002 86.AT902.003

76

Chapter 3

Removing the LCD Bezel

1. See Removing the LCD Module on page 60. 2. Remove the two upper and two lower bezel screw caps and screws.

Step LCD Bezel M2.5*5

Size 4

Quantity

Screw Type

3.

Starting from the upper inside edge of the bezel, pry the bezel upwards and away from the panel. Move along the sides until all sides of the bezel are removed. NOTE: If necessary, use a plastic pry to lift up the outside edges of the bezel.

Chapter 3

77

Removing the Inverter Board

1. See Removing the LCD Bezel on page 77. 2. Remove the securing screw and adhesive tape from the Inverter board.

Step Inverter Board M2.5*5

Size 1

Quantity

Screw Type

3. Disconnect the left Inverter board cable as shown.

4.

Lift the Inverter board clear of the LCD Module and disconnect the right cable.

5. Remove the Inverter board from the LCD module. 78 Chapter 3

Removing the Camera Module

1. See Removing the LCD Bezel on page 77. 2. Disconnect the Camera Module cable as shown.

3. Remove the single securing screw from the Camera Module.

Step Camera Module M2*L3

Size 1

Quantity

Screw Type

4. Lift the Camera Module, left side first, clear of the LCD Module.

Chapter 3

79

Removing the LCD Panel

1. See Removing the LCD Bezel on page 77. 2. Remove the two securing screws from the LCD Module.

Step LCD Panel M2.5*5

Size 2

Quantity

Screw Type

3. Lift the LCD Panel clear of the LCD Module.

80

Chapter 3

Removing the LCD Brackets and FPC Cable

1. See Removing the LCD Panel on page 80. 2. Turn the LCD panel over to expose the rear. Lift the camera connector clear of the panel.

3. Lift the adhesive protector and disconnect the cable from the LCD Panel.

4. Grip the FPC cable and lift upward to detach the adhesive pads and remove the cable from the panel. 5. Remove the eight securing screws (four on each side) from the LCD Panel brackets.

Step LCD Brackets M2*L3

Size 8

Quantity

Screw Type

6. Remove the LCD brackets by pulling away from the LCD Panel as shown.

Chapter 3

81

Removing the Antennas

1. See Removing the LCD Panel on page 80. 2. Remove the strips holding the antenna cables in place. Ensure the cables are free from obstructions.

3. Remove the tab securing the left antenna to the LCD module.

4. Remove the tab securing the right antenna to the LCD module.

5. Remove the antenna cables and assembly from the LCD module.

82

Chapter 3

Removing the MIC Module

1. See Removing the Antennas on page 82. 2. Remove the strips holding the MIC Module cable in place. Ensure the cable is free from obstructions.

3. Remove the MIC cable and Module from the LCD module. NOTE: If the left antenna is present, it may be necessary to lift the assembly to free the Mic cable.

Chapter 3

83

LCD Module Reassembly Procedure

Replacing the LCD Panel
1. Replace the left antenna and cable as shown. Ensure that the cable is inserted under each tab strip.

2. Replace the right antenna and cable as shown. Ensure that the cable is inserted under each tab strip.

3. Replace the MIC cable under antenna and replace the MIC as shown.

84

Chapter 3

4. Replace the securing strips holding the Mic cable in place.

5. Align the LCD brackets as shown. Starting with the top most screws (marked with screws (four on each side) in the brackets as shown.

) replace the eight

6. Turn the panel over. Insert the LCD Panel cable into the LCD Panel as shown.

Chapter 3

85

7. Align the LCD Panel cable as shown and press down to engage the adhesive pads.

8. Place the LCD Panel in the back cover.

9. Secure the LCD module with the two securing screws.

10. Insert the Camera Module right side first to engage 11. Replace the single securing screw. the securing clip.

86

Chapter 3

12. Connect the Camera Module cable.

13. Connect the right side inverter cable.

14. Connect the left side inverter cable and place the inverter in the LCD module.

15. Replace the single securing screw and adhesive tape.

Chapter 3

87

Replacing the LCD Bezel

1. Locate the bezel correctly and press down the edges until there are no gaps between the bezel and the LCD Module.

2. Replace the four screws and the rubber screw caps provided.

88

Chapter 3

Main Module Reassembly Procedure

Replacing the CPU
1. Carefully turn the mainboard upside down (CPU 2. Using a plastic screw driver, lock the CPU in the side up), and insert the CPU into the CPU bracket socket as shown. as shown.

Replacing the Thermal Module

1. Align and place the Thermal Module in the mounting as shown.

2. Replace the four screws (in numerical order from screw 1 to screw 4) to secure the Thermal Module.

3 1

2 4

Chapter 3

89

Replacing the CPU Fan Module

1. Align the Fan Module on the screw brackets. 2. Replace the three securing screws.

3. Connect the Fan cable to the Mainboard.

Replacing the Mainboard

1. Turn the Mainboard over. Connect the DC IN Cable to the Mainboard.

90

Chapter 3

2. Ensure that the Mainboard is face up (the Heatsink and CPU are not visible). Place the Mainboard in the chassis, left side first (1), and press down to install (2). NOTE: Make sure the I/O ports are positioned correctly through the lower cover, and the screw sockets are visible through the mainboard.

3. Replace the single securing screw.

4. Press down on the DC IN cable to secure the adhesive in place.

Replacing the Modem Module

1. Connect the Modem cable to the Modem Module as shown. 2. Replace the Modem Module and secure the two screws as shown.

Chapter 3

91

Replacing the Power Board

1. Feed the Power Board FFC thought the upper base as shown. 2. Place the Power Board on the upper base and replace the adhesive strip.

3. Turn the upper base over and replace the adhesive strip securing the Power Board FFC in place.

92

Chapter 3

Replacing the Speaker Module

1. Replace the left side speaker in the upper base and secure it using the two screws provided. Install the speaker cable, taking care to follow the path as shown.

2. Replace the right side speaker in the upper base and secure it using the two screws provided. Install the speaker cable, taking care to follow the path as shown

3. Replace the Power Board FFC over the speaker cable as shown.

Chapter 3

93

4. Replace the adhesive tape to secure the speaker cable in place.

94

Chapter 3

Replacing the TouchPad Bracket

IMPORTANT:The TouchPad cannot be removed individually. To replace the TouchPad, replace the entire Upper Cover. 1. Replace the TouchPad bracket bottom edge first to 2. Slide the TouchPad bracket in the direction of the engage the securing clips. arrow to engage the securing clip.

3. Replace the two securing screws from the TouchPad bracket.

4. Replace the TouchPad FFC and press down to secure with the adhesive strips.

Replacing the Upper Case

1. Place the upper case on the lower case front edge 2. Lower the case into position, as shown, and press first. down around the edges to secure it in place.

Chapter 3

95

3. Reconnect the three cables as shown. A

C Reconnect A as shown. Replace the adhesive tape to on cable A.

Reconnect B as shown and secure the cable latch.

Reconnect C as shown and secure the cable latch.

96

Chapter 3

4. Replace the seven screws as shown.

5. Turn the computer over and replace the eight screws as shown.

Replacing the LCD Module

1. Align the LCD hinges with the lower case and replace the LCD module.

2. Replace the four securing screws (two each side), starting with the left side hinge. NOTE: Two different screw sizes are used to secure the LCD module in place. The red callouts require M2.5*8 screws and the blue callouts require M2.5*5 screws.

Chapter 3

97

3. Reconnect the two LCD module interface cables as shown.

4. Replace the protective film over the cables.

5. Turn the computer over and replace the two screws to secure the LCD module in place.

98

Chapter 3

Replacing the Antenna Cable

IMPORTANT:The antenna cable must run along the supplied cable channels and use all the available cable clips to avoid damage to components during reassembly. 1. Run the antenna cable along the cable channel using all the cable clips as shown. 2. Feed the cable through the chassis and pull it through from the under side of the computer. Secure the cable in place using the adhesive tape.

3. Turn the computer over and run the cable along the cable channel as shown.

Chapter 3

99

Replacing the Keyboard

1. Reconnect keyboard FFC to the mainboard, and secure the locking latch. 2. Turn the keyboard over and place the front edge first in the mounting.

3. Rotate the keyboard downward and press gently in to place.

100

Chapter 3

Replacing the Switch Cover

1. Place the Switch Cover left side first on to the upper case as shown. 2. Press down along the length of the cover to secure it in place.

3. Turn the computer over and replace the two securing screws.

Chapter 3

101

Replacing the ODD Module

1. With the ODD tray in the eject position, replace the 2. Press the cover into the tray, bottom edge first, to ODD cover on the new ODD Module. secure.

3. Turn ODD Module around and secure bracket with 4. Slide the module in the chassis and press until the three screws. module is flush with the chassis.

5. Replace the single screw to secure the Module.

102

Chapter 3

Replacing the Hard Disk Drive Module

1. Place the HDD in the HDD carrier. 2. Replace the four screws to secure the carrier.

3. Insert the HDD, interface side first, and lower it into 4. Slide the HDD to the left to secure in place. place.

Chapter 3

103

Replacing the WLAN Module

1. Insert the WLAN board into the WLAN socket. 2. Replace the two screws to secure the module.

3. Connect the two antenna cables to the module. NOTE: The white antenna cable connects to the upper terminal and the black antenna cable to the lower terminal.

Replacing the DIMM Modules

NOTE: To replace DIMM Module 2, first remove DIMM Module 1. In this procedure, only DIMM Module 1 is shown. 1. Insert the DIMM Module in place. 2. Press down to lock the DIMM module in place.

104

Chapter 3

Replacing the Lower Covers

1. Replace the Memory Cover. 2. Replace the WLAN Cover.

3. Replace HDD Cover.

4. Replace the three screws in the memory and WLAN bays and secure the two captive screws in the HDD cover.

Chapter 3

105

Replacing the Battery

1. Slide and hold the battery release latch to the release position (1), insert the battery pack and press down (2). 2. Slide the battery lock/unlock latch to the lock position.

2 1

106

Chapter 3

Chapter 4

Troubleshooting
Common Problems
Use the following procedure as a guide for computer problems. NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options can give false errors and invalid system responses. 1. 2. 3. Obtain the failing symptoms in as much detail as possible. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating the same operation. Use the following table with the verified symptom to determine which page to go to. Symptoms (Verified) Power On Issue No Display Issue LCD Failure Internal Keyboard Failure TouchPad Failure Internal Speaker Failure Internal Microphone Failure ODD Failure Modem Failure WLAN Failure Thermal Unit Failure Other Functions Failure Intermittent Failures Undermined Failures 4. Go To Page 108 Page 109 Page 111 Page 111 Page 112 Page 112 Page 114 Page 116 Page 119 Page 119 Page 120 Page 121 Page 122 Page 122

If the Issue is still not resolved, see Online Support Information on page 161.

Chapter 4

107

Power On Issue
If the system doesnt power on, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs:

Computer Shutsdown Intermittently

If the system powers off at intervals, perform the following actions one at a time to correct the problem. 1. 2. 3. 4. 5. 6. 7. 8. Check the power cable is properly connected to the computer and the electrical outlet. Remove any extension cables between the computer and the outlet. Remove any surge protectors between the computer and the electrical outlet. Plug the computer directly into a known good electrical outlet. Disconnect the power and open the casing to check the Thermal Unit (see Thermal Unit Failure on page 120) and fan airways are free of obstructions. Disable the power management settings in the BIOS to ensure they are not the cause of the problem (see Power on page 29). Remove all external and non-essential hardware connected to the computer that are not necessary to boot the computer to the failure point. Remove any recently installed software. If the Issue is still not resolved, see Online Support Information on page 161.

108

Chapter 4

No Display Issue
If the Display doesnt work, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs:

No POST or Video
If the POST or video doesnt display, perform the following actions one at a time to correct the problem. 1. Make sure that the internal display is selected. On this notebook model, switching between the internal display and the external display is done by pressing Fn+F5. Reference Product pages for specific model procedures. Make sure the computer has power by checking at least one of the following occurs:

2.

Fans start up Status LEDs light up

If there is no power, see Power On Issue on page 108. 3. 4. Drain any stored power by removing the power cable and battery and holding down the power button for 10 seconds. Reconnect the power and reboot the computer. Connect an external monitor to the computer and switch between the internal display and the external display is by pressing Fn+F5 (on this model). If the POST or video appears on the external display, see LCD Failure on page 111. 5. Disconnect power and all external devices including port replicators or docking stations. Remove any memory cards and CD/DVD discs. Restart the computer. If the computer boots correctly, add the devices one by one until the failure point is discovered. 6. 7. 8. Reseat the memory modules. Remove the drives (see Disassembly Process on page 42). If the Issue is still not resolved, see Online Support Information on page 161.

Chapter 4

109

Abnormal Video Display

If video displays abnormally, perform the following actions one at a time to correct the problem. 1. 2. 3. 4. Reboot the computer. If permanent vertical/horizontal lines or dark spots display in the same location, the LCD is faulty and should be replaced. See Disassembly Process on page 42. If extensive pixel damage is present (different colored spots in the same locations on the screen), the LCD is faulty and should be replaced. See Disassembly Process on page 42. Adjust the brightness to its highest level. See the User Manual for instructions on adjusting settings. NOTE: Ensure that the computer is not running on battery alone as this may reduce display brightness. If the display is too dim at the highest brightness setting, the LCD is faulty and should be replaced. See Disassembly Process on page 42. 5. Check the display resolution is correctly configured: a. b. c. d. e. 6. 7. 8. Minimize or close all Windows. If display size is only abnormal in an application, check the view settings and control/mouse wheel zoom feature in the application. If desktop display resolution is not normal, right-click on the desktop and select Personalize Display Settings. Click and drag the Resolution slider to the desired resolution. Click Apply and check the display. Readjust if necessary.

Roll back the video driver to the previous version if updated. Remove and reinstall the video driver. Check the Device Manager to determine that:

The device is properly installed. There are no red Xs or yellow exclamation marks. There are no device conflicts. No hardware is listed under Other Devices.

9.

If the Issue is still not resolved, see Online Support Information on page 161.

10. Run the Windows Memory Diagnostic from the operating system DVD and follow the onscreen prompts. 11. If the Issue is still not resolved, see Online Support Information on page 161.

Random Loss of BIOS Settings

If the computer is experiencing intermittent loss of BIOS information, perform the following actions one at a time to correct the problem. 1. 2. 3. If the computer is more than one year old, replace the CMOS battery. Run a complete virus scan using up-to-date software to ensure the computer is virus free. If the computer is experiencing HDD or ODD BIOS information loss, disconnect and reconnect the power and data cables between devices. If the BIOS settings are still lost, replace the cables. 4. 5. 6. If HDD information is missing from the BIOS, the drive may be defective and should be replaced. Replace the Motherboard. If the Issue is still not resolved, see Online Support Information on page 161.

110

Chapter 4

LCD Failure
If the LCD fails, perform the following actions one at a time to correct the problem. Do not replace a nondefective FRUs:

Built-In Keyboard Failure

If the built-in Keyboard fails, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs:

Chapter 4

111

TouchPad Failure
If the TouchPad doesnt work, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs:

Internal Speaker Failure

If the internal Speakers fail, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs:

112

Chapter 4

Sound Problems
If sound problems are experienced, perform the following actions one at a time to correct the problem. 1. 2. Reboot the computer. Navigate to Start Control Panel System and Maintenance the Device Manager to determine that:

System

Device Manager. Check

The device is properly installed. There are no red Xs or yellow exclamation marks. There are no device conflicts. No hardware is listed under Other Devices.

3. 4. 5.

Roll back the audio driver to the previous version, if updated recently. Remove and reinstall the audio driver. Ensure that all volume controls are set mid range: a. b. Click the volume icon on the taskbar and drag the slider to 50. Ensure that the volume is not muted. Click Mixer to verify that other audio applications are set to 50 and not muted.

6.

Navigate to Start Control Panel Hardware and Sound Sound. Ensure that Speakers are selected as the default audio device (green check mark). NOTE: If Speakers does not show, right-click on the Playback tab and select Show Disabled Devices (clear by default). Select Speakers and click Configure to start Speaker Setup. Follow the onscreen prompts to configure the speakers. Remove and recently installed hardware or software. Restore system and file settings from a known good date using System Restore. If the issue is not fixed, repeat the preceding steps and select an earlier time and date.

7. 8. 9.

10. Reinstall the Operating System. 11. If the Issue is still not resolved, see Online Support Information on page 161.

Chapter 4

113

Internal Microphone Failure

If the internal Microphone fails, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs:

Microphone Problems
If internal or external Microphones do no operate correctly, perform the following actions one at a time to correct the problem. 1. 2. 3. 4. 5. 6. 7. Check that the microphone is enabled. Navigate to Start Sound and select the Recording tab. Control Panel Hardware and Sound

Right-click on the Recording tab and select Show Disabled Devices (clear by default). The microphone appears on the Recording tab. Right-click on the microphone and select Enable. Select the microphone then click Properties. Select the Levels tab. Increase the volume to the maximum setting and click OK. Test the microphone hardware: a. b. c. d. Select the microphone and click Configure. Select Set up microphone. Select the microphone type from the list and click Next. Follow the onscreen prompts to complete the test.

8.

If the Issue is still not resolved, see Online Support Information on page 161.

114

Chapter 4

HDD Not Operating Correctly

If the HDD does not operate correctly, perform the following actions one at a time to correct the problem. 1. 2. 3. Disconnect all external devices. Run a complete virus scan using up-to-date software to ensure the computer is virus free. Run the Windows Vista Startup Repair Utility: a. b. c. d. e. f. insert the Windows Vista Operating System DVD in the ODD and restart the computer. When prompted, press any key to start to the operating system DVD. The Install Windows screen displays. Click Next. Select Repair your computer. The System Recovery Options screen displays. Click Next. Select the appropriate operating system, and click Next.

NOTE: Click Load Drivers if controller drives are required. g. h. i. Select Startup Repair. Startup Repair attempts to locate and resolve issues with the computer. When complete, click Finish.

If an issue is discovered, follow the onscreen information to resolve the problem. 4. 5. 6. 7. 8. 9. Run the Windows Memory Diagnostic Tool. For more information see Windows Help and Support. Restart the computer and press F2 to enter the BIOS Utility. Check the BIOS settings are correct and that CD/DVD drive is set as the first boot device on the Boot menu. Ensure all cables and jumpers on the HDD and ODD are set correctly. Remove any recently added hardware and associated software. Run the Windows Disk Defragmenter. For more information see Windows Help and Support. Run Windows Check Disk by entering chkdsk /r from a command prompt. For more information see Windows Help and Support.

10. Restore system and file settings from a known good date using System Restore. If the issue is not fixed, repeat the preceding steps and select an earlier time and date. 11. Replace the HDD. See Disassembly Process on page 42.

Chapter 4

115

ODD Failure
If the ODD fails, perform the following actions one at a time to correct the problem. Do not replace a nondefective FRUs:

ODD Not Operating Correctly

If the ODD exhibits any of the following symptoms it may be faulty:

Audio CDs do not play when loaded DVDs do not play when loaded Blank discs do not burn correctly DVD or CD play breaks up or jumps Optical drive not found or not active:

Not shown in My Computer or the BIOS setup LED does not flash when the computer starts up The tray does not eject

Access failure screen displays The ODD is noisy

Perform the following general solutions one at a time to correct the problem. 1. 2. 3. 4. Reboot the computer and retry the operation. Try an alternate disc. Navigate to Start Storage panel. Navigate to Start Computer. Check that the ODD device is displayed in the Devices with Removable Control Panel System and Maintenance System Device Manager.

116

Chapter 4

a. b. c. d. e.

Double-click lDE ATA/ATAPI controllers. If a device displays a down arrow, right-click on the device and click Enable. Double-click DVD/CD-ROM drives. If the device displays a down arrow, right-click on the device and click Enable. Check that there are no yellow exclamation marks against the items in lDE ATA/ATAPI controllers. If a device has an exclamation mark, right-click on the device and uninstall and reinstall the driver. Check that there are no yellow exclamation marks against the items in DVD/CD-ROM drives. If a device has an exclamation mark, right-click on the device and uninstall and reinstall the driver. If the exclamation marker is not removed from the item in the lists, try removing any recently installed software and retrying the operation.

Discs Do Not Play

If discs do not play when inserted in the drive, perform the following actions one at a time to correct the problem. 1. 2. 3. 4. Check that the disc is correctly seated in the drive tray and that the label on the disc is visible. Check that the media is clean and scratch free. Try an alternate disc in the drive. Ensure that AutoPlay is enabled: a. b. c. 5. Navigate to Start Control Panel Hardware and Sound AutoPlay.

Select Use AutoPlay for all media and devices. In the Audio CD and DVD Movie fields, select the desired player from the drop down menu.

Check that the Regional Code is correct for the selected media:

IMPORTANT:Region can only be changed a limited number of times. After Changes remaining reaches zero, the region cannot be changed even Windows is reinstalled or the drive is moved to another computer. a. b. c. d. Navigate to Start Control Panel System and Maintenance System Device Manager.

Double-click DVD/CD-ROM drives. Right-click DVD drive and click Properties, then click the DVD Region tab. Select the region suitable for the media inserted in the drive.

Discs Do Not Burn Properly

If discs can not be burned, perform the following actions one at a time to correct the problem. 1. Ensure that the default drive is record enabled: a. b. c. 2. Navigate to Start Computer and right-click the writable ODD icon. Click Properties.

Select the Recording tab. In the Desktop disc recording panel, select the writable ODD from the drop down list. Click OK.

Ensure that the software used for burning discs is the factory default. If using different software, refer to the software's user manual.

Playback is Choppy
If playback is choppy or jumps, perform the following actions one at a time to correct the problem. 1. Check that system resources are not running low: a. b. 2. Try closing some applications. Reboot and try the operation again.

Check that the ODD controller transfer mode is set to DMA: a. Navigate to Start Control Panel System and Maintenance System Device Manager. 117

Chapter 4

b. c. d.

Double-click IDE ATA/ATAPI controllers, then right-click ATA Device 0. Click Properties and select the Advanced Settings tab. Ensure that the Enable DMA box is checked and click OK. Repeat for the other ATA Devices shown if applicable.

Drive Not Detected

If Windows cannot detect the drive, perform the following actions one at a time to correct the problem. 1. 2. Restart the computer and press F2 to enter the BIOS Utility. Check that the drive is detected in the ATAPI Model Name field on the Information page. NOTE: Check that the entry is identical to one of the ODDs specified in Hardware Specifications and Configurations on page 16. Turn off the power and remove the cover to inspect the connections to the ODD. See Disassembly Process on page 42. a. b. c. 4. 5. Check for broken connectors on the drive, motherboard, and cables. Check for bent or broken pins on the drive, motherboard, and cable connections. Try an alternate cable, if available. If the drive works with the new cable, the original cable should be replaced.

3.

Reseat the drive ensuring and all cables are connected correctly. Replace the ODD. See Disassembly Process on page 42.

Drive Read Failure

If discs cannot be read when inserted in the drive, perform the following actions one at a time to correct the problem. 1. 2. Remove and clean the failed disc. Retry reading the CD or DVD. d. e. f. Test the drive using other discs. Play a DVD movie Listen to a music CD

If the ODD works properly with alternate discs, the original disc is probably defective and should be replaced. 3. Turn off the power and remove the cover to inspect the connections to the ODD. See Disassembly Process on page 42. a. b. c. 4. Check for broken connectors on the drive, motherboard, and cables. Check for bent or broken pins on the drive, motherboard, and cable connections. Try an alternate cable, if available. If the drive works with the new cable, the original cable should be replaced.

Replace the ODD. See Disassembly Process on page 42.

118

Chapter 4

Modem Function Failure

If the internal Modem fails, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs:

Wireless Function Failure

If the WLAN fails, perform the following actions one at a time to correct the problem. Do not replace a nondefective FRUs:

Chapter 4

119

Thermal Unit Failure

If the Thermal Unit fails, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs:

External Mouse Failure

If an external Mouse fails, perform the following actions one at a time to correct the problem. 1. 2. 3. 4. 5. 6. 7. 8. Try an alternative mouse. If the mouse uses a wireless connection, insert new batteries and confirm there is a good connection. See the mouse user manual. If the mouse uses a USB connection, try an alternate USB port. Try an alternative program to verify mouse operation. Reinstall the program experiencing mouse failure. Restart the computer. Remove any recently added hardware and associated software. Remove any recently added software and reboot. Restore system and file settings from a known good date using System Restore. If the issue is not fixed, repeat the preceding steps and select an earlier time and date. 9. Run the Event Viewer to check the events log for errors. For more information see Windows Help and Support.

10. Roll back the mouse driver to the previous version if updated recently. 11. Remove and reinstall the mouse driver. 12. Check the Device Manager to determine that:

The device is properly installed. There are no red Xs or yellow exclamation marks. There are no device conflicts.

120

Chapter 4

No hardware is listed under Other Devices.

13. If the Issue is still not resolved, see Online Support Information on page 161.

Other Failures
If the CRT Switch, Dock, LAN Port, external MIC or Speakers, PCI Express Card, 5-in-1 Card Reader or Volume Wheel fail, perform the following general steps to correct the problem. Do not replace a non-defective FRUs: 1. 2. 3. Check Drive whether is OK. Check Test Fixture is ok. Swap M/B to Try.

Chapter 4

121

Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a recurring problem exists. When analyzing an intermittent problem, do the following: 1. 2. 3. Run the advanced diagnostic test for the system board in loop mode at least 10 times. If no error is detected, do not replace any FRU. If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.

Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect, whether a short circuit is suspected, or whether the system is inoperative. Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU). NOTE: Verify that all attached devices are supported by the computer. NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See Power On Issue on page 108.): 1. 2. 3. Power-off the computer. Visually check them for damage. If any problems are found, replace the FRU. Remove or disconnect all of the following devices:

Non-Acer devices Printer, mouse, and other external devices Battery pack Hard disk drive DIMM CD-ROM/Diskette drive Module PC Cards

4. 5. 6. 7.

Power-on the computer. Determine if the problem has changed. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU. If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:

System board LCD assembly

122

Chapter 4

Post Codes
These tables describe the POST codes and descriptions during the POST.

Sec:
NO_EVICTION_MODE_DEBUG EQU 1 (CommonPlatform\sec\Ia32\SecCore.inc) Code 0xC2 0xC3 0xC4 0xC5 0xCF MTRR setup Enable cache Establish cache tags Enter NEM, Place the BSP in No Fill mode, set CR0.CD = 1, CR0.NW = 0 Cache Init Finished Description

Memory:
DEBUG_BIOS equ 1 (Chipset\Alviso\MemoryInitAsm\IA32\IMEMORY.INC) Code 0xA0 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x20 0x21 0x22 0x23 0x24 0x25 0x26 First memory check point Enable MCHBAR Check for DRAM initialization interrupt and reset fail Verify all DIMMs are DDR or DDR2 and unbuffered Detect an improper warm reset and handle Detect if ECC SO-DIMMs are present in the system Verify all DIMMs are single or double sided and not asymmetric Verify all DIMMs are x8 or x16 width Find a common CAS latency between the DIMMS and the MCH Determine the memory frequency and CAS latency to program Determine the smallest common TRAS for all DIMMs Determine the smallest common TRP for all DIMMs Determine the smallest common TRCD for all DIMMs Determine the smallest refresh period for all DIMMs Verify burst length of 8 is supported by all DIMMs Determine the smallest tWR supported by all DIMMs Determine DIMM size parameters Program the correct system memory frequency Determine and set the mode of operation for the memory channels Program clock crossing registers Disable Fast Dispatch Program the DRAM Row Attributes and DRAM Row Boundary registers Program the DRAM Bank Architecture register Program the DRAM Timing & and DRAM Control registers Program ODT Perform steps required before memory init Program the receive enable reference timing control register Program the DLL Timing Control Registers, RCOMP settings 123 Description

Chapter 4

Code 0x27 0x28 0x29 0x30 0x31 0x32 0x33 0x34 0x35 0x43

Description Enable DRAM Channel I/O Buffers Enable all clocks on populated rows Perform JEDEC memory initialization for all memory rows Perform steps required after memory init Program DRAM throttling and throttling event registers Setup DRAM control register for normal operation and enable Enable RCOMP Clear DRAM initialization bit in the SB Initialization Sequence Completed, program graphic clocks Program Thermal Throttling

BDS & Specific action:

Code 0x00 0x12 0x13 0x21 0x27 0x28 0x50 0x51 0x58 0x5A 0x79 0x7A 0x90 0x91 0x92 0x93 0x94 0x95 0x98 0x99 0x9A 0x9B 0xB8 0xB9 0xBB 0xE4 0xF8 0xF9 Wake up the Aps Initialize SMM Private Data and relocate BSP SMBASE PC init begin at the stage1 Report every memory range do the hard ware ECC init Report status code of every memory range Get the root bridge handle Notify pci bus driver starts to program the resource Reset the host controller IdeBus begin initialization Report that the remote terminal is being disabled Report that the remote terminal is being enabled Keyboard reset USB Keyboard disable Keyboard detection Report that the usb keyboard is being enabled Clear the keyboard buffer Init Keyboard Mouse reset Mouse disable Detect PS2 mouse Report that the mouse is being enabled Peripheral removable media reset (ex: IsaFloppy, USB device) Peripheral removable media disable Peripheral removable media enable Report Status Code here for DXE_ENTRY_POINT once it is available Report that ExitBootServices() has been called Runtime driver set virtual address map Description Report the legacy boot is happening

124

Chapter 4

Each PEIM entry point used in 80_PORT

Code 0x00 0x01 0xA1 0xA2 0xA3 0xA4 0x06 0x07 0xA5 0xA6 0xA7 0xA8 0x0C 0xAA 0xAC 0x0F 0x40 0x41 0xAD 0xAB 0xAE 0x16 0x17 0x16~0x1F 0x20~0x2E 0xAF PEI_EVENT_LOG PEI_OEM_SERVICE PEI_SIO_INIT PEI_MONO_STATUS_CODE PEI_CPU_IO_PCI_CFG PEI_CPU_IO PEI_PCI_CFG PEI_CPU_PEIM PEI_PLATFORM_STAGE1 PEI_VARIABLE PEI_SB_INIT PEI_CAPSULE PEI_PLATFORM_STAGE2 PEI_SB_SMBUS_ARP_DISABLED PEI_HOST_TO_SYSTEM PEI_MEMORY_INIT PEI_S3_RESUME PEI_CLOCK_GEN PEI_OP_PRESENCE PEI_FIND_FV PEI_H2O_DEBUG_IO PEI_H2O_DEBUG_COMM PEI_RESERVED PEI_OEM_DEFINED PEI_DXE_IPL Description

Each Driver entry point used in 80_PORT

Code 0x30 0xB6 0xB8 0xB9 0xBA 0xBB 0xBC 0xBE 0xBF 0xC0 0xC1 0xC2 0xC3 Chapter 4 RESERVED DXE_CRC32_SECTION_EXTRACT SCRIPT_SAVE ACPI_S3_SAVE SMART_TIMER JPEG_DECODER PCX_DECODER HT_CPU / MP_CPU LEGACY_METRONOME FTWLITE RUN_RIME MONOTONIC_COUNTER WATCH_DOG_TIMER 125 Description

Code 0xC4 0xC5 0xC6 0xC7 0xC8 0xC9 0xD9 0x45 0xD6 0xD7 0xD5 0xDA 0xDB 0xDD 0xE7 0xE8 0xE9 0xED 0xEC 0xF6 0xF7 0xF8 0xFB 0xFC 0xFD 0x97 0x98 0x99 0x82 0x83 0x84 0x85 0x88 0x89 0x60 0x8B 0x62 0x8D 0x8E 0x8F 0x70 0x71 SECURITY_STUB DXE_CPU_IO CF9_RESET PC_RTC STATUS_CODE VARIABLE EMU_VARIABLE

Description

DXE_CHIPSET_INIT DXE_ALERT_FORMAT PCI_HOST_BRIDGE PCI_EXPRESS DXE_SB_INIT IDE_CONTROLLER SATA_CONTROLLER SB_SM_BUS ISA_ACPI_DRIVER ISA_BUS ISA_SERIAL BUS_PCI_UNDI PCI_BUS BOOT_PRIORITY FVB_SERVICE ACPI_PLATFORM PCI_HOT_PLUG DXE_PLATFORM PLATFORM_IDE SMBIOS MEMORY_SUB_CLASS MISC_SUB_CLASS CON_PLATFORM SAVE_MEMORY_CONFIG ACPI_SUPPORT CON_SPLITTER_UGA_VGA / CON_SPLITTER VGA_CLASS DATA_HUB DISK_IO MEMORY_TEST CRISIS_RECOVERY LEGACY_8259 LEGACY_REGION LEGACY_INTERRUPT BIOS_KEYBOARD BIOS_VEDIO

126

Chapter 4

Code 0x72 0x73 0x75 0x76 0x6C 0x6D 0x6E 0x6F 0x74 0xFA 0x90 0x78 0x86 0x87 0x8A 0x7C 0x7D 0x7E 0x7F 0x9E 0x9F 0x8C 0xF9 0x72 0xBD 0x8D 0x8E 0x8F 0xA0 0xB3 0xB4 0xB7 0x9B 0xA9 0x9C 0x9D 0xCB 0xB5 0x11 0xB0 0xB1 MONITER_KEY LEGACY_BIOS

Description

LEGACY_BIOS_PLATFORM PCI_PLATFORM ISA_FLOOPY PS2_MOUSE USB_BOT USB_CBI0 USB_MOUSE SETUP_UTILITY FW_BLOCK_SERVICE SMM_USB_LEGACY GRAPHICS_CONSOLE TERMINAL DATA_HUB_STD_ERR FAT PARTITION ENGLISH FRENCH HII_DATABASE OEM_SETUP_BROWSER OEM_BADGING_SUPPORT SETUP_MOUSE MONITOR_KEY PLATFORM_BDS RESERVED RESERVED RESERVED DXE_H2O_DEBUG_IO DXE_TPM_TCG DXE_TPM_PHYSICAL_PRESENCE DXE_OEM_SERVICE DXE_ SECURITY_HDD_PASSWORD_SERVICE DXE_LAN_IDER_CONTROLLER DXE_ SECURITY_SYSTEM_PASSWORD_SERVICE DXE_ SECURITY_ PASSWORD_CONSOLE DXE_ DATA_HUB_RECORD_POLICY DXE_TPM_DRIVER CHINESE JAPANESE DXE_UNICODE_COLLACTION

Chapter 4

127

Each SmmDriver entry point used in 80_PORT

Code 0xD4 0xDE 0xCC 0xD2 0xDF 0xD0 0xCA 0xFE 0xD8 0x90 0x91 0x92 0x93 0x94 0x95 0xD3 Description SMM_ACCESS SMM_CONTROL SMM_BASE SMM_RUNTIME SB_SMM_DISPATCH SMM_THUNK SMM_ACPI_SW_CHILD SMM_PLATFORM SMM_GMCH_MBI SMM_FW_BLOCK_SERVICE SMM_VARIABLE SMM_IHISI SMM_INT15_MICROCODE SMM_PNP SMM_INIT_PPM SMM_OEM_SERVICE

128

Chapter 4

Chapter 5

Jumper and Connector Locations

Top View

Item SW4 JLVDS1 JP3 JP6 JP7 LED2 SW3

Description Wireless LAN Button LCD Connector Speaker Connector Power/B Connector TouchPad Connector Battery LED TouchPad (right) Button

Item JP1 JP5 JP4 U9 LED1 SW2

Description Internal MIC Connector Fun/B Connector Keyboard Connector South Bridge Power/SUSP LED TouchPad (left) Button

Chapter 5

129

Bottom View

Item JCPU1 JDIMM1 JHP1 JMIC1 JP12 JSATA1 JUSB1 PJP1 U31

Description CPU Socket Memory DIMM1 Connector Head-Phone Connector MIC-In Jack Fan Connector ODD Connector USB Connector AC-IN Connector North Bridge

Item JCRT1 JDIMM2 JLINE1 JMINI2 JRJ45 JSATA2 JUSB2 PJP2

Description CRT Connector Memory DIMM2 Connector Line-In Jack Wireless Card Connector RJ45 Connector HDD Connector USB Connector Battery Connector

130

Chapter 5

Clearing Password Check and BIOS Recovery

This section provide you the standard operating procedures of clearing password and BIOS recovery for eMachines D720/D520 Series. eMachines D720/D520 provide one Hardware Open Gap on main board for clearing password check, and one Hotkey for enabling BIOS Recovery.

Clearing Password Check

Hardware Open Gap Description
Item R347 (RTC_RST) Description Clear CMOS Jumper

Steps for Clearing BIOS Password Check

If users set BIOS Password (Supervisor Password and/or User Password) for a security reason, BIOS will ask the password during systems POST or when systems enter to BIOS Setup menu. However, once it is necessary to bypass the password check, users need to short the HW Gap to clear the password by the following steps:

Power Off a system, and remove HDD, AC and Battery from the machine. Open the back cover of the machine, and find out the HW Gap on M/B as picture. Use an electric conductivity tool to short the two points of the HW Gap. Plug in AC, keep the short condition on the HW Gap, and press Power Button to power on the system till BIOS POST finish. Then remove the tool from the HW Gap. Restart system. Press F2 key to enter BIOS Setup menu.

If there is no Password request, BIOS Password is cleared. Otherwise, please follow the steps and try again. NOTE: The steps are only for clearing BIOS Password (Supervisor Password and User Password).

Chapter 5

131

BIOS Recovery by Crisis Disk

BIOS Recovery Boot Block:
BIOS Recovery Boot Block is a special block of BIOS. It is used to boot up the system with minimum BIOS initialization. Users can enable this feature to restore the BIOS firmware to a successful one once the previous BIOS flashing process failed.

BIOS Recovery Hotkey:

The system provides a function hotkey: Fn+Esc, for enable BIOS Recovery process when system is powered on during BIOS POST. To use this function, it is strongly recommended to have the AC adapter and Battery present. If this function is enabled, the system will force the BIOS to enter a special BIOS block, called Boot Block.

Steps for BIOS Recovery from USB Storage:

Before doing this, prepare the Crisis USB key. The Crisis USB key could be made by executing the Crisis Disk program in another system with Windows XP OS. Follow the steps below: 1. 2. 3. Save ROM file (file name: JAL90x64.fd) to the root directory of USB storage. Plug USB storage into USB port. Press Fn + ESC button then plug in AC. The Power button flashes once. 4. Press Power button to initiate system CRISIS mode. When CRISIS is complete, the system auto restarts with a workable BIOS. 5. Update the latest version BIOS for this machine by regular BIOS flashing process.

132

Chapter 5

Chapter 6

FRU (Field Replaceable Unit) List

This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of eMachines D720/D520. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization). Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code from those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer office to order FRU parts for repair and service of customer machines. NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how to dispose it properly, or follow the rules set by your regional Acer office on how to return it.

Chapter 6

133

eMachines D720/D520 Exploded Diagrams

Main Assembly
5

1 2

6 7 8

10 11 4

No. 1 2 3 4 5 6

Description Mini Door HDD Door Ram Door Lower Case Middle Cover Keyboard

Acer P/N 7 8 9 10 11

No.

Description Power Board Upper Case Mainboard CPU Fan Heatsink

Acer P/N

134

Chapter 6

LCD Panel
1

4 9 5 6 10

11

No. 1 2 3 4 5 6

Description LCD Bezel LCD Panel Left Antenna LCD Cable Left Hinge Mic Cable

Acer P/N 7 8 9 10 11

No.

Description Camera Module Right Antenna Right Hinge Inverter LCD Assembly

Acer P/N

Chapter 6

135

eMachines D720/D520 FRU List

Category Adapter ADAPTER 65W 3PIN DELTA SADP65KB BFJA OBL ADAPTER 65W 3PIN DELTA SADP-65KB DFA ADAPTER 65W 3PIN LITEON PA-1650-02AC ADAPTER 65W 3PIN HIPRO AC-OK065B13 Battery BATTERY LI-ION 6CELLS 4.4AH SANYO BATTERY LI-ION 6CELLS 4.4AH SONY BATTERY LI-ION 6CELLS SP SM 3S2P 4.4AH SIMPLO BATTERY LI-ION 6CELLS SP SM 3S2P 4.8AH SIMPLO BATTERY LI-ION 6CELLS SP LG 3S2P 4.4AH SIMPLO BATTERY LI-ION 6CELLS SP PA 3S2P 4.4AH 7 043 0FA SIMPLO BATTERY LI-ION 6CELLS 4.4AH PANASONIC Board POWER BOARD MODEM BOARD MINI CARD BROADCOM T77H030.00 54MBPS BRCM4312 MINI CARD ATHEROS T60H976.00 (FW-06) 54M XB63 Cable T/P FFC POWER CORD US 3 PIN POWER CORD EU 3 PIN POWER CORD AUS 3 PIN POWER CORD UK 3 PIN POWER CORD CHINA 3 PIN POWER CORD SWISS 3 PIN POWER CORD ITALIAN 3 PIN POWER CORD DENMARK 3 PIN POWER CORD JP 3 PIN POWER CORD SOUTH AFRICA 3 PIN POWER CORD KOERA 3 PIN POWER CORD ISRAEL 3 PIN POWER CORD INDIA 3 PIN POWER CORD TWN 3 PIN POWER CORD ARGENTINA 3 PIN Case/Cover/ Bracket Assembly MIDDLE COVER UPPER CASE ASSY LOWER CASE ASSY W/ RJ11 LOWER CASE ASSY W/O RJ11 T/P BRACKET 60.N0902.001 60.N0902.002 60.N0902.003 60.N0902.004 33.N0902.001 50.N0902.001 27.TAVV5.001 27.TAVV5.002 27.TAVV5.003 27.TAVV5.004 27.TAVV5.005 27.TAVV5.006 27.TAVV5.007 27.TAVV5.008 27.TAVV5.009 27.TAVV5.010 27.TAVV5.011 27.TAVV5.012 27.TAVV5.013 27.TAVV5.014 27.APV02.001 55.N0902.001 55.N0902.002 NI.23600.029 NI.23600.007 BT.00603.041 BT.00604.024 BT.00607.034 TBD TBD BT.00607.015 BT.00605.020 AP.06501.014 AP.06501.013 TBD TBD Description Acer Part No.

136

Chapter 6

Category RAM DOOR MINI DOOR HDD DOOR CPU/Processor

Description

Acer Part No. 42.N0902.001 42.N0902.002 42.N0902.003

CPU INTEL P575 2G LF80537NF0411M SLB6M M0 CPU INTEL P585 2.16G LF80537NF0481M SLB6L M0 CPU INTEL T1600 1.66G LF80537NF0281MN SLB6J M0 CPU INTEL T1700 1.83G LF80537NF0341MN SLB6H M0 CPU INTEL T3200 2G LF80537GF0411M SLAVG M0 CPU INTEL T3400 2.16G LF80537GF0481M SLB3P M0 Multi Drive DVD SUPER MULTI DRIVE MODEL DVD SUPER MULTI DRIVE HLDS GSA-T50N DVD SUPER MULTI DRIVE HLDS GSA-T50N (ML) DVD SUPER MULTI DRIVE PIONEER DVR-TD08RS DVD SUPER MULTI DRIVE PLDS DS-8A2S DVD SUPER MULTI DRIVE SONY AD-7560S DVD SUPER MULTI DRIVE TOSHIBA TS-L633A ODD BEZEL-SUPER MULTI ODD BRACKET Combo Drive DVD/CDRW COMBO DRIVE MODULE DVD/CDRW COMBO DRIVE TSST TS-L463A DVD/CDRW COMBO DRIVE SONY CRX890S ODD BEZEL-COMBO ODD BRACKET HDD 6M.N0902.002 KO.02401.006 KO.0240E.009 42.N0902.005 33.N0902.002 6M.N0902.001 KU.0080D.029 KU.0080D.034 KU.00805.044 KU.0080F.001 KU.0080E.009 KU.00801.021 42.N0902.004 33.N0902.002

Chapter 6

137

Category

Description HDD SATA 120G 5400RPM HGST HTS542512K9SA00 HDD SATA 120G 5400RPM TOSHIBA MK1246GSX 0FA HDD SATA 120G 5400RPM SEAGATE ST9120817AS HDD SATA 120G 5400RPM WD WD1200BEVS-22UST0 HDD SATA 160G 5400RPM HGST HTS542516K9SA00 HDD SATA 160G 5400RPM HGST HTS543216L9A300 HDD SATA 160G 5400RPM TOSHIBA MK1646GSX HDD SATA 160G 5400RPM SEAGATE ST9160827AS HDD SATA 160G 5400RPM SEAGATE ST9160310AS HDD SATA 160G 5400RPM WD WD1600BEVT-22ZCT0 HDD SATA 250G 5400RPM HGST HTS542525K9SA00 HDD SATA 250G 5400RPM TOSHIBA MK2546GSX HDD SATA 250G 5400RPM SEAGATE ST9250827AS HDD SATA 250G 5400RPM WD WD2500BEVS-22UST0 HDD SATA 320G 5400RPM HGST HTS543232L9A300 HDD SATA 320G 5400RPM SEAGATE ST9320320AS HDD SATA 320G 5400RPM WD WD3200BEVT-22ZCT0 HDD CARRIER

Acer Part No. KH.12007.014 KH.12004.007 KH.12001.032 KH.12008.019 KH.16007.016 KH.16007.019 KH.16004.002 KH.16001.029 KH.16001.034 KH.16008.022 KH.25007.011 KH.25004.001 KH.25001.011 KH.25008.018 KH.32007.004 KH.32001.008 KH.32008.013 33.N0902.003

Keyboard

138

Chapter 6

Category

Description KEYBOARD INTE(UI) US INTERNATION KEYBOARD (ARE) ARABIC ENGLISH KEYBOARD (BE) BELGIAN KEYBOARD (BZ) BRAZILIAN KEYBOARD (CF) CANADIAN FRENCH KEYBOARD (CH) T-CHINESE KEYBOARD (DM) DENMARK KEYBOARD (NL) NETHERLANDS KEYBOARD (FR) FRENCH KEYBOARD (GR) GERMAN KEYBOARD (GK) GREEK KEYBOARD (HG) HUNGARY KEYBOARD (IT) ITALIAN KEYBOARD (KO) KOREAN KEYBOARD (NW) NORWEGIAN KEYBOARD (PO) PORTUGUESE KEYBOARD (RU) RUSSIAN KEYBOARD (SA/CR) SLOVENIAN KEYBOARD (SV) SLOVAK KEYBOARD (SP) SPANISH KEYBOARD (CZ/SK) CZECH-SLOVAKIAN KEYBOARD (SW) SWITZERLAND KEYBOARD (TI) THAILAND KEYBOARD (TR) TURKISH KEYBOARD UK KEYBOARD (HB) HEBREW KEYBOARD (ND) SCANDINAVIAN KEYBOARD (AR/FR) ARABIC/FRENCH KEYBOARD (CB) CANADIAN BILINGUAL KEYBOARD (SD) SWEDISH

Acer Part No.

LCD ASSY LCD MODULE 14.1 IN. WXGA GLARE W/ANTENNA CCD LCD PANEL G 14.1" WXGA AUO B141EW04 V4 LCD PANEL G 14.1" WXGA SAMSUNG LTN141W3-L01-J LCD PANEL G 14.1" WXGA CMO N141I3-L02 LCD PANEL G 14.1" WXGA LPL LP141WX3-TLN1 INVERTER BOARD LCD CABLE ANTENNA-R ANTENNA-L LCD COVER LCD BEZEL LCD BRACKET-R 6M.N0902.003 LK.14105.018 LK.14106.014 LK.1410D.016 LK.14108.014 19.N0902.001 50.N0902.002 50.N0902.003 50.N0902.004 60.N0902.005 60.N0902.006 33.N0902.004

Chapter 6

139

Category LCD BRACKET-L CAMERA MODULE 0.3M SCREW PAD Mainboard

Description

Acer Part No. 33.N0902.005 57.N0902.001 47.N0902.001 MB.N0902.001

MAINBOARD EMD720/EMD520 INTEL GL40 ICH9 PROPRIETARY V1.0 LF Memory RAM 512MB DDRII 667 NANYA NT512T64UH8B0FN-3C RAM 512MB DDRII 667 SAMSUNG M470T6464QZ3-CE6 RAM 512MB DDRII 667 HYNIX HYMP164S64CP6-Y5 RAM 1GB DDRII 667 NANYA NT1GT64U8HB0BN-3C RAM 1GB DDRII 667 SAMSUNG M470T2864QZ3-CE6 RAM 1GB DDRII 667 HYNIX HYMP112S64CP6-Y5 RAM 2GB DDRII 667 HYNIX HYMP125S64CP8-Y5 RAM 2GB DDRII 667 SAMSUNG M470T5663QZ3-CE6 Fan FAN Heatsink CPU THERMAL MODULE Speaker MIC SET SPEAKER R&L Miscellaneous NAME PLATE-D520 NAME PLATE-D720 RUBBER FOOT-L RUBBER FOOT-S RUBBER FOOT-HDD DOOR

KN.51203.032 KN.5120B.026 KN.5120G.024 KN.1GB03.014 KN.1GB0B.016 KN.1GB0G.012 KN.2GB0G.004 KN.2GB0B.003 23.N0902.001 60.N0902.007 23.N0902.002 23.N0902.003 40.N0902.001 40.N0902.002 47.N0902.002 47.N0902.003 47.N0902.004

Screw List
Category SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW,M2.5X8(NL) SCREW,M2.5X5(NL) SCREW,M2X3(NL) SCREW,M2.5X4(NL) SCREW,M2X4-NI(NL) SCREW,M3X3(NL) SCREW,M2.5X6.5(NL) Description Acer Part No. 86.AT902.001 86.AT902.002 86.AT902.003 86.AT902.004 86.AT902.005 86.AT902.006 86.AT902.007

140

Chapter 6

Chapter 6

141

Appendix A

Model Definition and Configuration

eMachines D720/D520 Series
Model Description
Model eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi RO PA PA PA PA EMEA EMEA EMEA EMEA EMEA EMEA EMEA EMEA EMEA EMEA EMEA EMEA EMEA EMEA EMEA Country Canada USA ACLAPortuguese ACLA-Spanish Eastern Europe Hungary Slovenia/ Croatia Portugal Spain Greece Israel Italy Turkey Turkey Middle East Middle East Middle East Middle East Middle East Acer Part No LX.N110C.004 LX.N110C.003 LX.N110C.002 LX.N110C.001 LX.N110Y.052 LX.N110Y.050 LX.N110Y.051 LX.N110Y.049 LX.N110Y.048 LX.N110Y.044 LX.N110Y.045 LX.N110Y.046 LX.N110Y.043 LX.N110Y.047 LX.N110Y.042 LX.N110Y.040 LX.N110Y.041 LX.N110Y.039 LX.N110Y.038 Description eMD520-571G12Mi LINPUSeCA1 UMA 1*1G/120/6L/CB_bg_EN31 eMD520-571G12Mi LINPUSeUS1 UMA 1*1G/120/6L/CB_bg_EN31 eMD520-571G12Mi LINPUSeXC1 UMA 1*1G/120/6L/CB_bg_EN61 eMD520-571G12Mi LINPUSeEA3 UMA 1*1G/120/6L/CB_bg_EN61 eMD520-571G12Mi VHB32eTEU6 UMA 1*1G/120/6L/CB_bg_CS21 eMD520-571G12Mi VHB32eTHU1 UMA 1*1G/120/6L/CB_bg_HU11 eMD520-571G12Mi VHB32eTSI1 UMA 1*1G/120/6L/CB_bg_EN11 eMD520-571G12Mi VHB32eTPT1 UMA 1*1G/120/6L/CB_bg_PT11 eMD520-571G12Mi VHB32eTES1 UMA 1*1G/120/6L/CB_bg_ES21 eMD520-571G12Mi VHB32eTGR1 UMA 1*1G/120/6L/CB_bg_EL21 eMD520-571G12Mi VHB32eTIL1 UMA 1*1G/120/6L/CB_bg_HE11 eMD520-571G12Mi VHB32eTIT1 UMA 1*1G/120/6L/CB_bg_IT11 eMD520-571G12Mi EM VHB32eTTR1 UMA 1*1G/120/6L/CB_bg_TR41 eMD520-571G12Mi EM VHB32eTTR1 UMA 1*1G/120/6L/CB_bg_TR11 eMD520-571G12Mi EM VHB32eTME9 UMA 1*1G/120/6L/CB_bg_FR21 eMD520-571G12Mi EM VHB32eTME2 UMA 1*1G/120/6L/CB_bg_AR21 eMD520-571G12Mi EM VHB32eTME6 UMA 1*1G/120/6L/CB_bg_EN11 eMD520-571G12Mi EM VHB32eTME3 UMA 1*1G/120/6L/CB_bg_FR21 eMD520-571G12Mi EM VHB32eTME2 UMA 1*1G/120/6L/CB_bg_AR11

Appendix A

142

Model eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Ci eMD520571G12Ci eMD520571G12Ci eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi 143

RO EMEA EMEA CHINA CHINA CHINA CHINA CHINA CHINA EMEA EMEA EMEA EMEA EMEA EMEA EMEA EMEA EMEA EMEA EMEA EMEA EMEA EMEA EMEA EMEA EMEA

Country Switzerland UK China Hong Kong China Hong Kong China China South Africa South Africa Denmark France Germany Belgium Holland Luxembourg Norway Russia Sweden/Finland Czech Eastern Europe Eastern Europe Eastern Europe Eastern Europe Eastern Europe

Acer Part No LX.N110Y.034 LX.N110Y.035 LX.N110Y.056 LX.N110Y.055 LX.N110Y.054 LX.N110Y.053 LX.N110C.015 LX.N110C.014 LX.N110Y.036 LX.N110Y.033 LX.N110Y.037 LX.N110Y.032 LX.N110Y.030 LX.N110Y.031 LX.N110Y.029 LX.N110Y.028 LX.N110Y.024 LX.N110Y.025 LX.N110Y.026 LX.N110Y.023 LX.N110Y.027 LX.N110Y.022 LX.N110Y.020 LX.N110Y.021 LX.N110Y.019

Description eMD520-571G12Mi VHB32eTCH1 UMA 1*1G/120/6L/CB_bg_IT41 eMD520-571G12Mi VHB32eTGB1 UMA 1*1G/120/6L/CB_bg_EN11 eMD520-571G12Mi VHB32eTCN1 UMA 1*1G/120/6L/CB_bg_AN_SC11 eMD520-571G12Mi VHB32eTHK2 UMA 1*1G/120/6L/CB_bg_AN_ZH31 eMD520-571G12Ci VHB32eTCN1 UMA 1*1G/120/6L/CB_bg_AN_SC11 eMD520-571G12Ci VHB32eTHK2 UMA 1*1G/120/6L/CB_bg_AN_ZH31 eMD520-571G12Ci LINPUSeCN1 UMA 1*1G/120/6L/CB_bg_AN_EN91 eMD520-571G12Mi LINPUSeCN1 UMA 1*1G/120/6L/CB_bg_AN_EN91 eMD520-571G12Mi EM VHB32eTZA1 UMA 1*1G/120/6L/CB_bg_FR21 eMD520-571G12Mi EM VHB32eTZA2 UMA 1*1G/120/6L/CB_bg_EN11 eMD520-571G12Mi VHB32eTDK1 UMA 1*1G/120/6L/CB_bg_NO11 eMD520-571G12Mi VHB32eTFR1 UMA 1*1G/120/6L/CB_bg_FR21 eMD520-571G12Mi VHB32eTDE1 UMA 1*1G/120/6L/CB_bg_DE11 eMD520-571G12Mi VHB32eTBE1 UMA 1*1G/120/6L/CB_bg_NL11 eMD520-571G12Mi VHB32eTNL1 UMA 1*1G/120/6L/CB_bg_NL11 eMD520-571G12Mi VHB32eTLU1 UMA 1*1G/120/6L/CB_bg_IT41 eMD520-571G12Mi VHB32eTNO1 UMA 1*1G/120/6L/CB_bg_NO11 eMD520-571G12Mi VHB32eTRU1 UMA 1*1G/120/6L/CB_bg_RU11 eMD520-571G12Mi VHB32eTSE1 UMA 1*1G/120/6L/CB_bg_FI11 eMD520-571G12Mi VHB32eTCZ2 UMA 1*1G/120/6L/CB_bg_SK11 eMD520-571G12Mi VHB32eTEU4 UMA 1*1G/120/6L/CB_bg_FI11 eMD520-571G12Mi VHB32eTEU3 UMA 1*1G/120/6L/CB_bg_RU11 eMD520-571G12Mi VHB32eTEU7 UMA 1*1G/120/6L/CB_bg_ENG1 eMD520-571G12Mi VHB32eTEU1 UMA 1*1G/120/6L/CB_bg_CS21 eMD520-571G12Mi VHB32eTEU2 UMA 1*1G/120/6L/CB_bg_HU21 Appendix A

Model eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi Appendix A

RO EMEA PA AAP AAP AAP AAP AAP AAP AAP AAP AAP AAP AAP AAP AAP AAP AAP AAP AAP AAP AAP AAP PA PA PA

Country Eastern Europe ACLA-Spanish Australia/New Zealand Singapore India Indonesia Indonesia Philippines Malaysia Thailand Vietnam Australia/New Zealand New Zealand Singapore Singapore India Indonesia Indonesia Philippines Malaysia Thailand Vietnam Canada USA ACLAPortuguese

Acer Part No LX.N110Y.018 LX.N110Y.004 LX.N110C.013 LX.N110C.012 LX.N110C.011 LX.N110C.010 LX.N110C.009 LX.N110C.008 LX.N110C.007 LX.N110C.006 LX.N110C.005 LX.N110Y.017 LX.N110Y.016 LX.N110Y.015 LX.N110Y.014 LX.N110Y.013 LX.N110Y.012 LX.N110Y.011 LX.N110Y.010 LX.N110Y.009 LX.N110Y.008 LX.N110Y.007 LX.N110Y.006 LX.N110Y.005 LX.N110Y.003

Description eMD520-571G12Mi VHB32eTEU5 UMA 1*1G/120/6L/CB_bg_PL11 eMD520-571G12Mi EM VHB32eTEA1 UMA 1*1G/120/6L/CB_bg_ES21 eMD520-571G12Mi LINPUSeAU1 UMA 1*1G/120/6L/CB_bg_EN11 eMD520-571G12Mi LINPUSeSG1 UMA 1*1G/120/6L/CB_bg_EN11 eMD520-571G12Mi LINPUSeIN1 UMA 1*1G/120/6L/CB_bg_EN11 eMD520-571G12Mi LINPUSeID1 UMA 1*1G/120/6L/CB_bg_ID21 eMD520-571G12Mi LINPUSeID1 UMA 1*1G/120/6L/CB_bg_EN11 eMD520-571G12Mi LINPUSePH1 UMA 1*1G/120/6L/CB_bg_EN11 eMD520-571G12Mi LINPUSeMY1 UMA 1*1G/120/6L/CB_bg_EN11 eMD520-571G12Mi LINPUSeTH1 UMA 1*1G/120/6L/CB_bg_EN11 eMD520-571G12Mi LINPUSeVN1 UMA 1*1G/120/6L/CB_bg_EN11 eMD520-571G12Mi VHB32eTAU1 UMA 1*1G/120/6L/CB_bg_EN11 eMD520-571G12Mi VHB32eTNZ1 UMA 1*1G/120/6L/CB_bg_EN11 eMD520-571G12Mi VHB32eTSG1 UMA 1*1G/120/6L/CB_bg_EN11 eMD520-571G12Mi VHB32eTSG1 UMA 1*1G/120/6L/CB_bg_ZH31 eMD520-571G12Mi VHB32eTIN1 UMA 1*1G/120/6L/CB_bg_EN11 eMD520-571G12Mi EM VHB32eTID1 UMA 1*1G/120/6L/CB_bg_EN11 eMD520-571G12Mi EM VHB32eTID1 UMA 1*1G/120/6L/CB_bg_ID21 eMD520-571G12Mi EM VHB32eTPH1 UMA 1*1G/120/6L/CB_bg_EN11 eMD520-571G12Mi EM VHB32eTMY1 UMA 1*1G/120/6L/CB_bg_EN11 eMD520-571G12Mi EM VHB32eTTH1 UMA 1*1G/120/6L/CB_bg_TH21 eMD520-571G12Mi EM VHB32eTVN1 UMA 1*1G/120/6L/CB_bg_EN11 eMD520-571G12Mi VHB32eTCA2 UMA 1*1G/120/6L/CB_bg_FR31 eMD520-571G12Mi VHB32eTUS1 UMA 1*1G/120/6L/CB_bg_EN31 eMD520-571G12Mi EM VHB32eTXC1 UMA 1*1G/120/6L/CB_bg_XC21 144

Model eMD520571G12Mi eMD520571G12Mi eMD520570512Ci eMD520571G12Mi eMD720321G12Mi eMD720321G12C eMD720321G16Mi eMD720321G16Mi eMD720322G32Mi eMD720322G32Mi eMD720322G32Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Ci eMD520571G12Ci eMD520571G12Ci eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi

RO PA PA AAP WW WW CHINA CHINA

Country ACLAPortuguese ACLA-Spanish Vietnam WW WW China China

Acer Part No LX.N110Y.002 LX.N110Y.001 LX.N110C.016 S2.N110Y.001 S2.N250Y.001 LX.N250Y.003 LX.N250Y.002

Description eMD520-571G12Mi EM VHB32eTXC2 UMA 1*1G/120/6L/CB_bg_XC21 eMD520-571G12Mi EM VHB32eTEA3 UMA 1*1G/120/6L/CB_bg_ES21 eMD520-570512Ci LINPUSeVN1 UMA 1*512/120/6L/CB_bg_AN_EN11 eMD520-571G12Mi VHB32eWW1 UMA 2*512/120/6L/CB_bg_AN_EN13 eMD720-321G12Mi VHB32eWW1 UMAC 2*512/120/6L/CB_bg_0.3D_AN_EN13 eMD720-321G12CVHB32eTCN1 UMAC 1*1G/120/6L/CB_0.3D_AN_SC11 eMD720-321G16Mi VHB32eTCN1 UMAC 1*1G/160/6L/ CB_bg_0.3D_AN_SC11 eMD720-321G16Mi VHB32eTTW1 UMAC 1*1G/160/6L/ CB_bg_0.3D_AN_TC11 eMD720-322G32Mi VHB32eTCA2 UMAC 1*2G/320/6L/CB_bg_0.3D_AN_FR31 eMD720-322G32Mi VHB32eTUS1 UMAC 1*2G/320/6L/CB_bg_0.3D_AN_EN31 eMD720-322G32Mi EM VHB32eTEA1 UMAC 1*2G/320/6L/ CB_bg_0.3D_AN_ES21 eMD520-571G12Mi VHB32eTCN1 UMAC 1*1G/120/6L/ CB_bg_0.3D_AN_SC11 eMD520-571G12Mi VHB32eTHK2 UMAC 1*1G/120/6L/CB_bg_0.3D_AN_ZH31 eMD520-571G12Ci VHB32eTCN1 UMAC 1*1G/120/6L/CB_bg_0.3D_AN_SC11 eMD520-571G12Ci VHB32eTHK2 UMAC 1*1G/120/6L/CB_bg_0.3D_AN_ZH31 eMD520-571G12Ci LINPUSeCN1 UMAC 1*1G/120/6L/CB_bg_0.3D_AN_EN91 eMD520-571G12Mi LINPUSeCN1 UMAC 1*1G/120/6L/CB_bg_0.3D_AN_EN91 eMD520-571G12Mi LINPUSeAU1 UMAC 1*1G/120/6L/CB_bg_0.3D_EN11 eMD520-571G12Mi LINPUSeSG1 UMAC 1*1G/120/6L/CB_bg_0.3D_EN11 eMD520-571G12Mi LINPUSeIN1 UMAC 1*1G/120/6L/CB_bg_0.3D_EN11 eMD520-571G12Mi LINPUSeID1 UMAC 1*1G/120/6L/CB_bg_0.3D_ID21 eMD520-571G12Mi LINPUSeID1 UMAC 1*1G/120/6L/CB_bg_0.3D_EN11 eMD520-571G12Mi LINPUSePH1 UMAC 1*1G/120/6L/CB_bg_0.3D_EN11

TWN

GCTWN

LX.N250Y.001

PA PA PA

Canada USA ACLA-Spanish

LX.N250Y.006 LX.N250Y.005 LX.N250Y.004

CHINA

China

LX.N090Y.021

CHINA CHINA CHINA CHINA CHINA AAP AAP AAP AAP AAP AAP

Hong Kong China Hong Kong China China Australia/New Zealand Singapore India Indonesia Indonesia Philippines

LX.N090Y.020 LX.N090Y.019 LX.N090Y.018 LX.N090C.015 LX.N090C.014 LX.N090C.010 LX.N090C.009 LX.N090C.011 LX.N090C.008 LX.N090C.012 LX.N090C.007

145

Appendix A

Model eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520171G12Mi Appendix A

RO AAP AAP AAP AAP AAP AAP AAP AAP AAP AAP AAP AAP AAP AAP PA PA PA PA PA PA PA PA PA PA AAP

Country Malaysia Thailand Vietnam Australia/New Zealand New Zealand Singapore Singapore India Indonesia Indonesia Philippines Malaysia Thailand Vietnam Canada USA ACLAPortuguese ACLA-Spanish Canada USA ACLAPortuguese ACLAPortuguese ACLA-Spanish ACLA-Spanish Thailand

Acer Part No LX.N090C.013 LX.N090C.006 LX.N090C.005 LX.N090Y.017 LX.N090Y.013 LX.N090Y.012 LX.N090Y.014 LX.N090Y.011 LX.N090Y.015 LX.N090Y.010 LX.N090Y.016 LX.N090Y.009 LX.N090Y.008 LX.N090Y.007 LX.N090C.004 LX.N090C.003 LX.N090C.002 LX.N090C.001 LX.N090Y.005 LX.N090Y.004 LX.N090Y.006 LX.N090Y.003 LX.N090Y.002 LX.N090Y.001 LX.N090C.017

Description eMD520-571G12Mi LINPUSeMY1 UMAC 1*1G/120/6L/CB_bg_0.3D_EN11 eMD520-571G12Mi LINPUSeTH1 UMAC 1*1G/120/6L/CB_bg_0.3D_EN11 eMD520-571G12Mi LINPUSeVN1 UMAC 1*1G/120/6L/CB_bg_0.3D_EN11 eMD520-571G12Mi VHB32eTAU1 UMAC 1*1G/120/6L/CB_bg_0.3D_EN11 eMD520-571G12Mi VHB32eTNZ1 UMAC 1*1G/120/6L/CB_bg_0.3D_EN11 eMD520-571G12Mi VHB32eTSG1 UMAC 1*1G/120/6L/CB_bg_0.3D_EN11 eMD520-571G12Mi VHB32eTSG1 UMAC 1*1G/120/6L/CB_bg_0.3D_ZH31 eMD520-571G12Mi VHB32eTIN1 UMAC 1*1G/120/6L/CB_bg_0.3D_EN11 eMD520-571G12Mi EM VHB32eTID1 UMAC 1*1G/120/6L/CB_bg_0.3D_EN11 eMD520-571G12Mi EM VHB32eTID1 UMAC 1*1G/120/6L/CB_bg_0.3D_ID21 eMD520-571G12Mi EM VHB32eTPH1 UMAC 1*1G/120/6L/CB_bg_0.3D_EN11 eMD520-571G12Mi EM VHB32eTMY1 UMAC 1*1G/120/6L/CB_bg_0.3D_EN11 eMD520-571G12Mi EM VHB32eTTH1 UMAC 1*1G/120/6L/CB_bg_0.3D_TH21 eMD520-571G12Mi EM VHB32eTVN1 UMAC 1*1G/120/6L/CB_bg_0.3D_EN11 eMD520-571G12Mi LINPUSeCA1 UMAC 1*1G/120/6L/CB_bg_0.3D_EN31 eMD520-571G12Mi LINPUSeUS1 UMAC 1*1G/120/6L/CB_bg_0.3D_EN31 eMD520-571G12Mi LINPUSeXC1 UMAC 1*1G/120/6L/CB_bg_0.3D_EN61 eMD520-571G12Mi LINPUSeEA3 UMAC 1*1G/120/6L/CB_bg_0.3D_EN61 eMD520-571G12Mi VHB32eTCA2 UMAC 1*1G/120/6L/CB_bg_0.3D_FR31 eMD520-571G12Mi VHB32eTUS1 UMAC 1*1G/120/6L/CB_bg_0.3D_EN31 eMD520-571G12Mi EM VHB32eTXC1 UMAC 1*1G/120/6L/CB_bg_0.3D_XC21 eMD520-571G12Mi EM VHB32eTXC2 UMAC 1*1G/120/6L/CB_bg_0.3D_XC21 eMD520-571G12Mi EM VHB32eTEA3 UMAC 1*1G/120/6L/CB_bg_0.3D_ES21 eMD520-571G12Mi EM VHB32eTEA1 UMAC 1*1G/120/6L/CB_bg_0.3D_ES21 eMD520-171G12Mi LINPUSeTH1 UMAC 1*1G/120/6L/CB_bg_0.3D_AN_EN11 146

Model eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520570512Mi eMD520570512Ci eMD520572G12Mi eMD520581G12Mi eMD520582G25Mi eMD520161G12Mi eMD520162G25Mi eMD520172G25Mi eMD520171G12Mi eMD520570512Mi eMD720321G16M

RO PA PA PA

Country Canada USA ACLAPortuguese ACLA-Spanish

Acer Part No LX.N090Y.026 LX.N090Y.025 LX.N090Y.024

Description eMD520-571G12Mi VHB32eTCA2 UMAC 1*1G/120/6L/CB_bg_0.3D_AN_FR31 eMD520-571G12Mi VHB32eTUS1 UMAC 1*1G/120/6L/CB_bg_0.3D_AN_EN31 eMD520-571G12Mi EM VHB32eTXC2 UMAC 1*1G/120/6L/ CB_bg_0.3D_AN_XC21 eMD520-571G12Mi EM VHB32eTEA3 UMAC 1*1G/120/6L/ CB_bg_0.3D_AN_ES21 eMD520-571G12Mi EM VHB32eTEA1 UMAC 1*1G/120/6L/ CB_bg_0.3D_AN_ES21 eMD520-570512Mi LINPUSeID1 UMAC 1*512/120/6L/CB_bg_0.3D_AN_ID21 eMD520-570512Ci LINPUSeVN1 UMAC 1*512/120/6L/CB_bg_0.3D_AN_EN11 eMD520-572G12Mi LINPUSeIN1 UMAC 2*1G/120/6L/CB_bg_0.3D_AN_EN11 eMD520-581G12Mi LINPUSeIN1 UMAC 1*1G/120/6L/CB_bg_0.3D_AN_EN11 eMD520-582G25Mi LINPUSeIN1 UMAC 2*1G/250/6L/CB_bg_0.3D_AN_EN11 eMD520-161G12Mi LINPUSeIN1 UMAC 1*1G/120/6L/CB_bg_0.3D_AN_EN11 eMD520-162G25Mi LINPUSeIN1 UMAC 2*1G/250/6L/CB_bg_0.3D_AN_EN11 eMD520-172G25Mi LINPUSeIN1 UMAC 2*1G/250/6L/CB_bg_0.3D_AN_EN11 eMD520-171G12Mi LINPUSeIN1 UMAC 1*1G/120/6L/CB_bg_0.3D_AN_EN11 eMD520-570512Mi LINPUSeVN1 UMAC 1*512/120/6L/CB_bg_0.3D_AN_EN11 eMD720-321G16MLINPUSeCN1 UMA 1*1G/160/6L/CB_AN_EN91

PA

LX.N090Y.023

PA

ACLA-Spanish

LX.N090Y.022

AAP AAP AAP AAP AAP AAP AAP AAP AAP AAP CHINA

Indonesia Vietnam India India India India India India India Vietnam China

LX.N090C.019 LX.N090C.016 LX.N090C.026 LX.N090C.025 LX.N090C.024 LX.N090C.023 LX.N090C.022 LX.N090C.021 LX.N090C.020 LX.N090C.018 LX.N130C.001

Model eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi

CPU CM575 CM575 CM575 CM575 CM575 CM575 CM575

LCD N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG

Mem 1 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6

Mem 2 N N N N N N N

HDD 1(GB) N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS

ODD NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS

WLAN 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG

147

Appendix A

Model eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Ci eMD520571G12Ci eMD520571G12Ci eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi

CPU CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575

LCD N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG

Mem 1 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6

Mem 2 N N N N N N N N N N N N N N N N N N N N N N N N N N N

HDD 1(GB) N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS

ODD NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NCB24XS NCB24XS NCB24XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS

WLAN 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG

Appendix A

148

Model eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi

CPU CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575

LCD N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG

Mem 1 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6

Mem 2 N N N N N N N N N N N N N N N N N N N N N N N N N N N

HDD 1(GB) N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS

ODD NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS

WLAN 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG

149

Appendix A

Model eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520570512Ci eMD520571G12Mi eMD720321G12Mi eMD720321G12C eMD720321G16Mi eMD720321G16Mi eMD720322G32Mi eMD720322G32Mi eMD720322G32Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Ci eMD520571G12Ci eMD520571G12Ci eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi

CPU CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 PMDT 3200 PMDT 3200 PMDT 3200 PMDT 3200 PMDT 3200 PMDT 3200 PMDT 3200 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575

LCD N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG

Mem 1 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO512MBII6 SO512MBII6 SO512MBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO2GBII6 SO2GBII6 SO2GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6

Mem 2 N N N N N N N N N N N SO512MBII6 SO512MBII6 N N N N N N N N N N N N N N

HDD 1(GB) N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N160GB 5.4KS N160GB 5.4KS N320GB 5.4KS N320GB 5.4KS N320GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS

ODD NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NCB24XS NSM8XS NSM8XS NCB24XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NCB24XS NCB24XS NCB24XS NSM8XS NSM8XS NSM8XS

WLAN 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG N 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG

Appendix A

150

Model eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi

CPU CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575

LCD N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG

Mem 1 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6

Mem 2 N N N N N N N N N N N N N N N N N N N N N N N N N N N

HDD 1(GB) N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS

ODD NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS

WLAN 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG

151

Appendix A

Model eMD520571G12Mi eMD520171G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520571G12Mi eMD520570512Mi eMD520570512Ci eMD520572G12Mi eMD520581G12Mi eMD520582G25Mi eMD520161G12Mi eMD520162G25Mi eMD520172G25Mi eMD520171G12Mi eMD520570512Mi eMD720321G16M

CPU CM575 CMT1700 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM575 CM585 CM585 CMT 1600 CMT 1600 CMT 1700 CMT 1700 CM575 PMDT 3200

LCD N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG

Mem 1 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO512MBII6 SO512MBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO512MBII6 SO1GBII6

Mem 2 N N N N N N N N N SO1GBII6 N SO1GBII6 N SO1GBII6 SO1GBII6 N N N

HDD 1(GB) N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N120GB 5.4KS N250GB 5.4KS N120GB 5.4KS N250GB 5.4KS N250GB 5.4KS N120GB 5.4KS N120GB 5.4KS N160GB 5.4KS

ODD NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NCB24XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS

WLAN 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG 3rd WiFi BG N

Appendix A

152

Appendix B

Test Compatible Components

This computers compatibility is tested and verified by Acers internal testing department. All of its system functions are tested under Windows XP Home, Windows XP Pro environment. Refer to the following lists for components, adapter cards, and peripherals which have passed these tests. Regarding configuration, combination and test procedures, please refer to the eMachines D720/D520 Series Compatibility Test Report released by the Acer Mobile System Testing Department.

Appendix B

153

Microsoft Windows Vista Environment Test

Vendor Adapter Test F0000183 DELTA CN F0000183 DELTA CN 10001023 LITE-ON 60002015 HIPRO Audio Codec 9999995 ONE TIME VENDER Battery Test 60001921 SANYO 10001063 SONY 60001535 PANASONI C 60002162 SIMPLO 60002162 SIMPLO 60002162 SIMPLO 9999995 ONE TIME VENDER Camera Test 9999995 ONE TIME VENDER 9999995 ONE TIME VENDER 9999995 ONE TIME VENDER 9999995 ONE TIME VENDER 9999995 ONE TIME VENDER 0.3M DV Bison 0.3M DV Lotus_2 6CELL2.2 6CELL2.2 6CELL2.2 Battery SANYO AS-2007A Li-Ion 3S2P SANYO 6 cell 4400mAh Main COMMON Normal Type Battery SONY AS-2007A Li-Ion 3S2P SONY 6 cell 4400mAh Main COMMON Normal Type Battery PANASONIC AS-2007A Li-Ion 3S2P PANASONIC 6 cell 4400mAh Main COMMON PSS Battery SIMPLO AS-2007A Li-Ion 3S2P PANASONIC 6 cell 4400mAh Main COMMON PSS Battery SIMPLO AS-2007A Li-Ion 3S2P SAMSUNG 6 cell 2400mAh 2nd COMMON Battery SIMPLO AS-2007A Li-Ion 3S2P SAMSUNG 6 cell 4400mAh Main COMMON SDI 2.2mAh F type Foxconn Bluetooth FOX_BRM_2.0 F/W 300 ALC268 ALC268 65W 65W-DE 65W 65W Adapter DELTA 65W 1.7x5.5x11 SADP-65KB DFA LF level 4 Adapter DELTA 65W 1.7x5.5x11 SADP-65KB BFJA LV4 LF for OBL only Adapter LITE-ON 65W 1.7x5.5x11 PA-1650-02AC LF level 4 Adapter HIPRO 65W 19V 1.7x5.5x11 Yellow HPOK065B13 LED LF level 4 Type Description

6CELL2.2 6CELL2.4 6CELL2.2

Bluetooth Test BT 2.0

0.3M DV

Suyin 0.3M DV Camellia_2

Card Reader Test 5 in 1-Build in 5 in 1-Build in MS, MS Pro, SD, SC, XD

JMB385

JMicron JMB385 Card Reader: SD/MMC/MS/MS Duo/ MS-HG (1/4/8-bit) & xD (PCI Express) JMicron JMB385 Card Reader: SD/MMC/MS/MS Duo/ MS-HG (1/4/8-bit) & xD (PCI Express)

JMB385

154

Appendix B

Vendor 9999995 ONE TIME VENDER CPU Test 10001067 INTEL 10001067 INTEL 10001067 INTEL 10001067 INTEL 10001067 INTEL 10001067 INTEL 10001067 INTEL 10001067 INTEL 10001067 INTEL 10001067 INTEL 10001067 INTEL 10001067 INTEL 10001067 INTEL 10001067 INTEL 10001067 INTEL 10001067 INTEL 10001067 INTEL 10001067 INTEL 10001067 INTEL 10001067 INTEL 10001067 INTEL 10001067 INTEL C2DP8400 C2DP8600 C2DT9400 C2DP9500 C2DT9600 MVPQS CM575 CM585 PMDT3400 CMT1600 CMT1700 PMDT3200 C2DP8600 C2DP8600 C2DT9400 C2DT9400 C2DP9500 C2DP9500 C2DT9600 C2DT9600 MVPQS MVPQS JMB385

Type

Description JMicron JMB385 Card Reader: SD/MMC/MS/MS Duo/ MS-HG (1/4/8-bit) & xD (PCI Express)

CPU Intel Core2Dual P8400 PGA 2.26G 3M 1066 25W CPU Intel Core2Dual P8600 PGA 2.4G 1066 25W 3M CPU Intel Core2Dual T9400 PGA 2.53G 6M 1066 35W CPU Intel Core2Dual P9500 PGA 2.53G 6M 1066 25W CPU Intel Core2Dual T9600 PGA 2.8G 6M 1066 35W CPU Intel Core2Dual QS Montevina Penryn QS sample CPU Intel Celeron 575 PGA 2.0G 1M 667 MV CPU Intel Celeron 585 PGA 2.16G 1M 667 MV CPU Intel Pentium Dual-Core T3400 PGA 2.16G 1M 667 MV CPU Intel CeleronM T1600 1.66G 1M 667 Dual Core, MV CPU Intel CeleronM T1700 PGA 1.83G 1M 667 Dual Core, MV CPU Intel Pentium Dual-Core T3200 2.0G 1M 667 MV CPU Intel Core2Dual P8600 PGA 2.4G 1066 25W 3M CPU Intel Core2Dual P8600 PGA 2.4G 1066 25W 3M CPU Intel Core2Dual T9400 PGA 2.53G 6M 1066 35W CPU Intel Core2Dual T9400 PGA 2.53G 6M 1066 35W CPU Intel Core2Dual P9500 PGA 2.53G 6M 1066 25W CPU Intel Core2Dual P9500 PGA 2.53G 6M 1066 25W CPU Intel Core2Dual T9600 PGA 2.8G 6M 1066 35W CPU Intel Core2Dual T9600 PGA 2.8G 6M 1066 35W CPU Intel Core2Dual QS Montevina Penryn QS sample CPU Intel Core2Dual QS Montevina Penryn QS sample

Appendix B

155

Vendor HDD Test 60002005 HGST SG 60002005 HGST SG 60001994 WD 60002036 SEAGATE 60002036 SEAGATE 60001922 TOSHIBA DIGI 60002036 SEAGATE 60001922 TOSHIBA DIGI 60001922 TOSHIBA DIGI 60001922 TOSHIBA DIGI 60002005 HGST SG 60002005 HGST SG 60002005 HGST SG 60001994 WD 60002036 SEAGATE 60001994 WD 60002036 SEAGATE 60002005 HGST SG 60001994 WD 60001994 WD 60001922 TOSHIBA DIGI 60001922 TOSHIBA DIGI 156

Type N120GB5.4KS N120GB5.4KS N120GB5.4KS N160GB5.4KS N160GB5.4KS N160GB5.4KS

Description HDD HGST 2.5" 5400rpm 120GB HTS542512K9SA00 Bronco-B SATA II LF F/W:C31P HDD HGST 2.5" 5400rpm 120GB HTS543212L9A300 Falcon-B SATA LF F/W:C40C HDD WD 2.5" 5400rpm 120GB WD1200BEVS-22UST0 ML125 SATA LF F/W:01.01A01 HDD SEAGATE 2.5" 5400rpm 160GB ST9160827AS Corsair SATA LF F/W:3.AAA HDD SEAGATE 2.5" 5400rpm 160GB ST9160310AS Crockett SATA LF F/W:0303 HDD TOSHIBA 2.5" 5400rpm 160GB MK1646GSX Leo BS SATA I LF F/W:LB113J HDD SEAGATE 2.5" 5400rpm 120GB ST9120817AS Corsair SATA LF F/W:3.AAA HDD TOSHIBA 2.5" 5400rpm 120GB MK1246GSX Leo BS SATA I LF F/W:LB213J HDD TOSHIBA 2.5" 5400rpm 120GB MK1252GSX Virgo BS SATA LF F/W:LV010J HDD TOSHIBA 2.5" 5400rpm 250GB MK2546GSX Leo BS SATA I LF F/W:LB013J HDD HGST 2.5" 5400rpm 250GB HTS542525K9SA00 Bronco-B SATA II LF F/W:C31P HDD HGST 2.5" 5400rpm 160GB HTS542516K9SA00 Bronco-B SATA II LF F/W:C31P HDD HGST 2.5" 5400rpm 160GB HTS543216L9A300 Falcon-B SATA LF F/W:C40C HDD WD 2.5" 5400rpm 160GB WD1600BEVT-22ZCTO ML160 SATA LF F/W:11.01A11 HDD SEAGATE 2.5" 5400rpm 250GB ST9250827AS Corsair SATA LF F/W:3.AAA HDD WD 2.5" 5400rpm 250GB WD2500BEVS-22UST0 ML125 SATA LF F/W:01.01A01 HDD SEAGATE 2.5" 5400rpm 320GB ST9320320AS Crockett SATA LF F/W:0303 HDD HGST 2.5" 5400rpm 320GB HTS543232L9A300 Falcon-B SATA LF F/W:C40C HDD WD 2.5" 5400rpm 320GB WD3200BEVT-22ZCT0 ML160 SATA LF F/W:11.01A11 HDD WD 2.5" 5400rpm 250GB WD2500BEVT-22ZCT0 ML160 SATA LF F/W:11.01A11 HDD TOSHIBA 2.5" 5400rpm 320GB MK3252GSX Virgo BS SATA LF F/W:LV010J HDD TOSHIBA 2.5" 5400rpm 160GB MK1652GSX Virgo - BS SATA LF F/W:LV010J

N120GB5.4KS N120GB5.4KS

N120GB5.4KS

N250GB5.4KS

N250GB5.4KS N160GB5.4KS N160GB5.4KS N160GB5.4KS N250GB5.4KS N250GB5.4KS N320GB5.4KS N320GB5.4KS N320GB5.4KS N250GB5.4KS N320GB5.4KS

N160GB5.4KS

Appendix B

Vendor 60001922 TOSHIBA DIGI 60001922 TOSHIBA DIGI 60002005 HGST SG 60001994 WD 60001994 WD 60002005 HGST SG 60001922 TOSHIBA DIGI 60001994 WD 60002005 HGST SG 60001922 TOSHIBA DIGI 60002005 HGST SG 60002005 HGST SG 60002036 SEAGATE 60001922 TOSHIBA DIGI 60001922 TOSHIBA DIGI 60001922 TOSHIBA DIGI 60002005 HGST SG 60002005 HGST SG 60002036 SEAGATE LAN Test 9999995 ONE TIME VENDER RTL8111C

Type N250GB5.4KS

Description HDD TOSHIBA 2.5" 5400rpm 250GB MK2546GSX Leo BS SATA I LF F/W:LB013J HDD TOSHIBA 2.5" 5400rpm 250GB MK2546GSX Leo BS SATA I LF F/W:LB013J HDD HGST 2.5" 5400rpm 250GB HTS542525K9SA00 Bronco-B SATA II LF F/W:C31P HDD WD 2.5" 5400rpm 250GB WD2500BEVS-22UST0 ML125 SATA LF F/W:01.01A01 HDD WD 2.5" 5400rpm 250GB WD2500BEVS-22UST0 ML125 SATA LF F/W:01.01A01 HDD HGST 2.5" 5400rpm 250GB HTS542525K9SA00 Bronco-B SATA II LF F/W:C31P HDD TOSHIBA 2.5" 5400rpm 250GB MK2552GSX Virgo BS SATA LF F/W:LV010J HDD WD 2.5" 5400rpm 120GB WD1200BEVT-22ZCT0 ML160 SATA LF F/W: 11.01A11 HDD HGST 2.5" 5400rpm 250GB HTS543225L9A300 Falcon-B SATA LF F/W:C40C HDD TOSHIBA 2.5" 5400rpm 120GB MK1246GSX Leo BS SATA I LF F/W:LB213J HDD HGST 2.5" 5400rpm 120GB HTS542512K9SA00 Bronco-B SATA II LF F/W:C31P HDD HGST 2.5" 5400rpm 120GB HTS542512K9SA00 Bronco-B SATA II LF F/W:C31P HDD SEAGATE 2.5" 5400rpm 160GB ST9160827AS Corsair SATA LF F/W:3.AAA HDD TOSHIBA 2.5" 5400rpm 120GB MK1246GSX Leo BS SATA I LF F/W:LB213J HDD TOSHIBA 2.5" 5400rpm 160GB MK1646GSX Leo BS SATA I LF F/W:LB113J HDD TOSHIBA 2.5" 5400rpm 160GB MK1646GSX Leo BS SATA I LF F/W:LB113J HDD HGST 2.5" 5400rpm 160GB HTS542516K9SA00 Bronco-B SATA II LF F/W:C31P HDD HGST 2.5" 5400rpm 160GB HTS542516K9SA00 Bronco-B SATA II LF F/W:C31P HDD SEAGATE 2.5" 5400rpm 160GB ST9160827AS Corsair SATA LF F/W:3.AAA Realtek Lan RTL8111C

N250GB5.4KS

N250GB5.4KS N250GB5.4KS N250GB5.4KS N250GB5.4KS N250GB5.4KS

N120GB5.4KS N250GB5.4KS N120GB5.4KS

N120GB5.4KS N120GB5.4KS N160GB5.4KS N120GB5.4KS

N160GB5.4KS

N160GB5.4KS

N160GB5.4KS N160GB5.4KS N160GB5.4KS

Appendix B

157

Vendor LCD Test 60003316 AUO 60002215 SAMSUNG 60003089 LG 10001038 CMO Memory Test 60002045 HYNIX 60001993 NANYA 60002215 SAMSUNG 60002045 HYNIX 60001993 NANYA 60001993 NANYA 60002215 SAMSUNG 60002045 HYNIX 60001993 NANYA 60002215 SAMSUNG Modem Test 23707801 FOXCONN TW 23707801 FOXCONN TW 23707801 FOXCONN TW 10001067 INTEL ODD Test 60001922 TOSHIBA DIGI 10001063 SONY NCB24XS SO2GBII6

Type N14.1WXGAG N14.1WXGAG N14.1WXGAG N14.1WXGAG

Description LCD AUO 14.1" WXGA Glare B141EW04-V4 LF 200nit 16ms LCD SAMSUNG 14.1" WXGA Glare LTN141W3-L01-J L6 LF 200nit 16ms LCD LPL 14.1" WXGA Glare LP141WX3-TLN1 LF 200nit 16ms LCD CMO 14.1" WXGA Glare N141I3-L02 LF 200nit 10ms Memory HYNIX SO-DIMM DDRII 667 2GB HYMP125S64CP8-Y5 LF Memory NANYA SO-DIMM DDRII 667 512MB NT512T64UH8B0FN-3C LF 32*16 0.09um Memory SAMSUNG SO-DIMM DDRII 667 512MB M470T6464QZ3-CE6 LF Memory HYNIX SO-DIMM DDRII 667 512MB HYMP164S64CP6-Y5 LF 64*16 0.065um SO-DIMM DDRII 667 1GB NT1GT64U8HB0BN-3C (0.09U) Memory NANYA SO-DIMM DDRII 667 1GB NT1GT64UH8D0FN-3C LF 64*16 0.07um Memory SAMSUNG SO-DIMM DDRII 667 1GB M470T2864QZ3-CE6 LF Memory HYNIX SO-DIMM DDRII 667 1GB HYMP112S64CP6-Y5 LF Memory NANYA SO-DIMM DDRII 667 2GB NT2GT64U8HD0BN-3C LF 128*8 0.07um Memory SAMSUNG SO-DIMM DDRII 667 2GB M470T5663QZ3-CE6 LF Foxconn Delphi-AM5 V2H 1.5_3.3v T60M951

SO512MBII6 SO512MBII6 SO512MBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO1GBII6 SO2GBII6 SO2GBII6

Fox+LSI AM5 V2H 1.5_3.3V

Fox+Con MC4Z 1.5_3.3V

Foxconn Conexant -Unizion 1.5_3.3v T60M955.02

Fox+LSI AM5 V2 3.3V Aus

Foxconn Delphi-AM5 V2 3.3v Aus T60M951.3x

Northbridge Chipset Test GL40 NB Chipset Intel CS GL40NB

ODD TOSHIBA COMBO 12.7mm Tray DL 24X TSL463A LF W/O bezel SATA ODD SONY COMBO 12.7mm Tray DL 24X CRX890S LF W/O bezel SATA

NCB24XS

158

Appendix B

Vendor 60001922 TOSHIBA DIGI 60001939 PIONEER 23418669 HLDS 23418669 HLDS 10001063 SONY 10001070 PHILIPS 10001067 INTEL WLAN Test 23707801 FOXCONN TW 9999995 ONE TIME VENDER 9999995 ONE TIME VENDER 9999995 ONE TIME VENDER NSM8XS

Type

Description ODD TOSHIBA Super-Multi DRIVE 12.7mm Tray DL 8X TS-L633A LF W/O bezel SATA ODD PIONEER Super-Multi DRIVE 12.7mm Tray DL 8X DVR-TD08RS LF W/O bezel SATA ODD HLDS Super-Multi DRIVE 12.7mm Tray DL 8X GSA-T50N LF W/O bezel SATA ODD HLDS Super-Multi DRIVE 12.7mm Tray DL 8X GSA-T50N LF W/O bezel SATA Malaysia ODD SONY Super-Multi DRIVE 12.7mm Tray DL 8X AD-7560S LF W/O bezel SATA ODD PLDS Super-Multi DRIVE 12.7mm Tray DL 8X DS-8A2S LF W/O bezel SATA SB Chipset Intel CS ICH9M

NSM8XS NSM8XS NSM8XS NSM8XS NSM8XS

Southbridge Chipset Test ICH9M

3rd WiFi BG

Foxconn FOX_ATH_XB63 Foxconn Atheros XB63 minicard b/g Foxconn Wireless LAN Broadcom 4312 minicard b/g

3rd WiFi BG

3rd WiFi 1x2 BGN

Foxconn Wireless LAN Atheros AR5B91 1x2 BGN

3rd WiFi 1x2 BGN

Foxconn Wireless LAN Wireless LAN Ralink RT2700E 1x2 BGN

Appendix B

159

160

Appendix B

Appendix C

Online Support Information

This section describes online technical support services available to help you repair your Acer Systems. If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch office. Acer Branch Offices and Regional Business Units may access our website. However some information sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan. Acer's Website offers you convenient and valuable support resources whenever you need them. In the Technical Information section you can download information on all of Acer's Notebook, Desktop and Server models including:

Service guides for all models User's manuals Training materials Bios updates Software utilities Spare parts lists TABs (Technical Announcement Bulletin)

For these purposes, we have included an Acrobat File to facilitate the problem-free downloading of our technical material. Also contained on this website are:

Detailed information on Acer's International Traveler's Warranty (ITW) Returned material authorization procedures An overview of all the support services we offer, accompanied by a list of telephone, fax and email contacts for all your technical queries.

We are always looking for ways to optimize and improve our services, so if you have any suggestions or comments, please do not hesitate to communicate these to us.

Appendix C

161

162

Appendix C

Index
A
AFLASH Utility Antennas

E
33
EasyTouch Failure Euro

120

82

14 43

B
Battery Pack BIOS password control ROM size 16 ROM type 16 vendor 16 Version 16 BIOS Utility

External Module Disassembly Flowchart

44 16

F
Features 1

33 FPC Cable 81
Flash Utility FRU (Field Replaceable Unit) List

133

BIOS Supports protocol

16

2133 Advanced 24 Boot 31 Exit 32 Navigating 21

Onboard Device Configuration 27 Power 29 Save and Exit 32 Security 26 System Security 32

H
50 HDTV Switch Failure 120
Hard Disk Drive Module Hibernation mode

13 Hot Keys 11
hotkey

I
Indicators 9 Intermittent Problems 122

Board Layout Top View 129 brightness hotkeys

13

C
Camera Module caps lock on indicator

114 Internal Speaker Failure 112 inverter board 78

Internal Microphone Failure

79

J
Jumper and Connector Locations Top View 129

5, 9 Common Problems 108

computer on indicator CPU

129

K
Keyboard

5, 9

57

75

Keyboard Failure 111

D
DIMM Module 47 Display display hotkeys

L
LCD Bezel

77

3 13

81 LCD Failure 111

LCD Brackets LCD Module Disassembly Flowchart

76
163

80 lower cover 45
LCD Panel

Top

129
hotkey

Touch Pad

M
Main Unit Disassembly Flowchart Mainboard

13 65

Touch Pad Failure 112 TouchPad Bracket Troubleshooting Built-in KB Failure 111 EasyTouch Buttons 120 HDTV Switch 120 Internal Microphone 114 Internal Speakers 112 LCD Failure 111 Modem 119 No Display 109 ODD 116 Other Failures 121 Power On 108 Thermal Unit 120 Touch Pad 112 WLAN 119

54

71

media access

5, 9 Memory Check 108 Model Definition 142 Modem Board 70 Modem Failure 119
on indicator

N
No Display Issue hotkey num lock on indicator

109

Notebook Manager

13 5, 9

U
Undetermined Problems utility BIOS

122

O
ODD Failure

2133

116 52

Online Support Information 161 optical drive module

W
Windows 2000 Environment Test Wireless Function Failure WLAN Board

154

P
Panel

119

48

4 8

Bottom left 4 PC Card

9 108

Power On Failure

S
Speaker Module speakers hotkey System Block Diagram

67

13 3

T
Test Compatible Components 153 Thermal Unit Failure

120

164