File: 06-fc288 Page 1 of 3
Fault Code 288
SAE J1939 Multiplexing Remote Accelerator Pedal or Lever Data Error - Received Network Data Error
CODES REASON EFFECT
Fault Code: 288 SAE J1939 Multiplexing Remote The engine will not respond to the remote
PID(P), SID(S): P29 Accelerator Pedal or Lever Data throttle. Engine may only idle. The primary or
SPN: 974 Error - Received Network Data cab accelerator may be able to be used.
FMI: 19 Error. The OEM vehicle electronic
Lamp: Red control unit (VECU) detected a
SRT: fault with the remote accelerator.
SAE J1939 Multiplexing Remote Accelerator Pedal or Lever
Circuit Description:
Normally, switches, accelerators, and other components are connected to the engine ECM directly through individual
wires. Multiplexing allows those same components to be hard wired to an OEM Vehicle Electronic Control Unit (VECU)
or Transmission ECU in the cab. Then component values and states from components (such as sensors, accelerators,
and switches) can be transmitted from the OEM VECU to the Cummins engine ECM over the SAE J1939 datalink.
Messages sent from OEM VECU's or Transmissions ECU's are received by the Cummins engine ECM and used for
controlling the engine. The Cummins ECM and OEM VECU's must be configured properly so that proper operation of the
multiplexed components will occur.
Component Location:
The engine ECM is located on the intake side of the engine. The J1939 datalink wiring and VECU location varies by OEM.
Shop Talk:
This fault can occur when the OEM VECU detects an error on the remote throttle and or remote throttle enable switch.
The ECM has been set up properly (components enabled and OEM VECU source addressed correctly) to receive
multiplexed information for the remote throttle enable switch states and remote accelerator position over the J1939
datalink from an OEM VECU, and the OEM VECU is transmitting the message for that component. Most OEM's will not
have the circuitry to detect a remote throttle switch error.
The two types of errors that can occur for this fault are:
© 2008 Cummins Inc., Box 3005, Columbus, IN 47202-3005 U.S.A. Printed from QuickServe® Online.
All Rights Reserved. Last Modified: 08-Jul-2010
File: 06-fc288 Page 2 of 3
• The OEM VECU determines that the remote throttle signal line is shorted high or shorted low. This fault status is
transmitted to the Cummins ECM on the J1939 datalink, which causes this fault to occur in the Cummins ECM.
• When the remote throttle enable switch has a shorted high or shorted low error detected by the OEM VECU. This fault
status is transmitted to the ECM on the J1939 datalink, which causes this fault to occur in the ECM. Most OEM's will
not incorporate fault detection on a switch.
NOTE: It is still possible to get a Fault Code 285 or 286 if there is an incorrect setup in the OEM VECU or Cummins ECM
for other components, or the remote throttle and remote throttle switch, or the datalink is damaged. OEM configurations
must multiplex the remote throttle and remote throttle switch inputs together to allow the use of the J1939 multiplexing
feature for these components. INSITE™ can be used to monitor multiplexed components.
Refer to Troubleshooting Fault Code t05-288
© 2008 Cummins Inc., Box 3005, Columbus, IN 47202-3005 U.S.A. Printed from QuickServe® Online.
All Rights Reserved. Last Modified: 08-Jul-2010
File: 06-fc288 Page 3 of 3
© 2008 Cummins Inc., Box 3005, Columbus, IN 47202-3005 U.S.A. Printed from QuickServe® Online.
All Rights Reserved. Last Modified: 08-Jul-2010
