45 Flathead Engine Overhaul Manual

~-- -- -
''
ENGINE OVERHAUL
MANUAL
SOLO 45'' MODEL
WLA
•
1929-1952
•
SERVICE MANUAL
APPLYING TO
THE FOLLOWING
45 MODELS
1941 -1952
Side Valve Engine Models
45 cu. in. (750 c.c.)
Basic Drive Train

1941 and Later Servi-Car
•
Generally to
1929-40 45 models
CONTENTS
'•••graphs '•e••
CHAPTER 1. INTRODUCTION ......... . . .. . 1-2 6
CHAPTER 2. OVERHAUL OF ENGINE IN

VEHICLE ... . . 0 0 • • • • •
3- 18 7-42
SECTION I Description and engine data ... . 3 7
II Removal of cylinders and piston
assemblies .. . . . . . . . . . . . . . . 4-6 8-14
III Disassembly, cleaning, inspection,
repair and assembly . .. ... 7- 14 15-32
IV Installation .. .. . ... . . . . 15 33-35
v Adjustment and tests . . .. . .... 16-17 36-40
VI Fits and tolerances ... ... . .. .. 18 41-42
CHAPTER 3. ENGINE . .. . . . .. ... ... . . .. . .. . 19- 39 43- 86

SECTION I Engine disassembly into sub·
assemblies . . . . . . . . . . . . . 19-20 43-49
II Disassembly, cleaning, inspection
and repair and assembly of
cylinders and pistons, and con·
necting rod alinement . . . . . . . 21 50
Ill Disassembly, cleaning and inspec-
tion, fitt ing crank pin and
mainshaft roller bearings, and
assembling flywheel · assembly 22-27 51- 62
IV Cleaning, inspection, and repair
of crankcase assemblies and
gear case cover . . . . . . . . . . 28-35 63- 75
V Fitting and assembly of flywh eel
and crankcase assembly 36-37 76- 78
VI Engine assembly . . . ..... . .. . . 38 79- 83
VII F its and tolerances . ... .. ... . . . 39 84- 86
3
CONTENTS
CHAPTER 4. FUEL, INTAKE , AND EXHAUST

l"aragrap h1 ...... Paragraphs Pa ges
CHAPTER 10. BRAKES 93-102 167- 1 iS

SYSTEMS . . . . .. .. . ..... 40-53 87 IIIII
SECTION I R ear wht!el brake 93-97 167- 171
SECTION I Description of systems 40-41 87 II()
II F ront wheel brake 98-102 172-175
II Carburetor . 42-47 91 C)7
CHAPTER 11. CHAINS, SPROCKETS, WHEELS,
III Fuel strainer and fuel supply
AND HUBS 103-117 176-190
valve . . . . . . . . . . . . . . . . . . . 48-49 9K
SECTION I Wheel rims and spokes . 103-1 0 7 1 76- 1 78
IV Intake pipe, air cleaner, and fit-
tings .............. . 50-51 99 II Wheel hubs 108-114 179-185
V Exhaust system ....... . ..... . 52-53 100 III Chains and sprockets 115- 117 186-190
CHAPTER 12. STEERING SYSTEM . . . . . . 118-125 191- 195

CHAPTER 5. IGNITION SYSTEM . . . . . . . . . . .. 54-60 101- 106
SECTION I F ork .... 118-122 191-193
II Handlebars and controls . 123- 125 194-195
CHAPTER 6. GENERATING SYSTEM .. .... . .. 61-68 107- 125
CHAPTER 13. CHASSIS PARTS AND EQUIP:'v1ENT 126-144 196- 202
CHAPTER 7. HORN AND LIGHTING SYSTEM ... 69-78 126-134 SECTION I Frame and tanks . . . 126- 128 196-197
SECTION I Switches and instrument panel .. 69-73 126-130 II Mudguards, chain guards,
stands, a nd skid plate 129-132 198-199
II Horn and lights . . . 74-78 131-134
III Battery box, too! box , and foot-
boards 133-135 200
CHAPTER 8. CLUTCH . . . . .· . 79-86 135-143
IV Saddle and saddle post ... 136-137 201
SECTION I Description and data ......... . 79-80 135-136
V Equipment. . . . . 138-144 202
II Removal, disassembly, cleaning,
inspection, and repair ..... . 81-83 137- 139 CHAPTER 14. RoAD TEST OF ENGINE, TRANS -
III Assembly, installation, and MISSION, AND CLUTCH 145- 156 203-207
adjustment . . . . . . ... . . .. 84- 85 140-142 SECTION I Engine 145-151 203-206
IV Fits and tolerances ....... . ... . 86 143 II Transmission and clutch 152-156 207
CHAPTER 15. SPECIAL TOOLS . 157 208-210

C HAPTER 9. TRANSMISSION ... .. ..... . . . .. . 87-92 144- 166
SECTION I Description and data ......... . 87 144 REFERENCES 211-212
II D isassembly. cleaning, inspec- . . ..
INDEX . ... ... ... . 213 216
tion, and repair ....... ..... . 88-90 145-155
I II Assembly ... . .............. . 91 156- lhl
IV Fits and tolerances .. . ..... ... . 92 165 IMI
4
CHAPTER 2
CHAPTER 1 OVERHAUL OF ENGINE IN VEHICLE
INTRODUCTION Section I
DESCRIPTION AND ENGINE DATA
1. SCOPE.
a. The instructions contained in this manual are for the inforrnn 3. DESCRIPTION AND ENGINE DATA.
tion and guidance o f personnel charged with the maintenance and
repair of Harley-Davidson motorcycle, model WLA. These instruc a. Description. The vehicle is powered by a two-cylinder, V -type,
tions are supplementary to field and technical manuals prepared for L-head gasoline engine, operating on four-stroke, four-cycle principle.
the using arm. This manual does not contain information which is The bearings. pistons and rings. cylinder walls, bushings and gears
intended primarily for the using arm, since such information is ~re lu.bnc.ated .by a force-feed circulating oil system. Engine oil supply
available to ordnance maintenance personnel in 100-series TM's or ts mamtamed m a separate tank. T olerances and fits are held to close
FM's. standards, calling for precise and fine workmanship on the part of the
mechanic.
b . This manua l contains a description of, and procedure for, dis-
assembly, inspection and repair of engine, fuel system, ignition b. Engine Data.
system, generating system, transmission and clutch, and chassis. Engine type Y-type. L-head
c. TM 9 -879 contains th e replacement instructions of many com- Number of cylinders .... 2
ponents of this vehicle. This information is not repeated in this Engine cooling Air
manual.
Cylinder bore • 2¥4 in .
2. MWO AND MAJOR UNIT ASSEMBLY REPLACEMENT Stroke 313'1 6 in.
RECORD. Displacement .. 45.12 cu in .
a. Description. Every veh icle is supplied with a copy of A.G.O. Horsepower (N.A.C.C. rating) • 6.05
Form No. 478, which provides a means of keeping a record o f each Compression ratio 5.0 t o 1
MWO completed or major unit assembly replaced. This form includes Inclination of cylinders 45 deg
spaces for the vehicle named and U.S.A. Registration No., instruc- Lubrication Circulating oil system
tions for use, and information pertinent to the work accomplished. Fuel, gasoline 72 octane or higher
It is very important that the form be used as directed and that it
remain with the vehicle until the vehicle is removed from service. Engine (power unit) weight' . .. 114 lb
b.Instructions for Use. Personnel performing modifications o r
Rotation (sprocket side) . . Counterclockwise
maJor unit assembly replacements must record clearly on the form Ignition . .. Battery
a description of the work completed and must initial the form in the
columns provided. When each modification is completed , record the
date, hours and / or mileage, and MWO number . When major unit
assemblies. such as engines, transmissions, transfer cases, are replaced.
record the date, hours and / or mileage and nomenclature of the unit
assembly. Minor repairs and minor parts and accessory replacements
need not be recorded.
c. Early Modifications . Upon receipt by a third or fourth ech elon
repair facility of a vehicle for ·.nodification or repair, maintenance
personnel will record the MWO numbers of modifications applied
prior to the date of A.G.O. Form N o. 478.
6 7
REMOVAL OF CYLINDERS AND PISTON ASSEMBLIES
operation. Many operat ional noises may sound like they originate in
CHAPTER 2 the engine. F o r example: Front drive chain too loose or too tight will
cause scraping. grinding, or pounding noise. b esides causing jerky
OVERHAUL OF ENGINE IN VEHICLE (Cont'd) operation. Loose engine mountings will cause thumping, pounding
noises. Transmission loose on its fra me mounting base will cause
Section II pounding n oise. L oose valve tappets will cause excessive noise in the
REMOVAL OF CYLINDERS AND PISTON ASSEMBLIES engine gear case. Incorrect spark timing (advanced) will cause knock-
ing and engin e roughness. Therefore, see that a ll units are securely
4. PRELI~fi~A R Y INSTHUCTIO'\S. mounted and correctly adjusted before attempting to diagnose engine
noises. Too many motorcycles have been deadlined and engines and
a. Gen e r a l. When an engine needs repair. it is not always possible
to definitely determine beforehand whether repair can be made with transmission units exchanged because simple p reventive maintenance
only upper end disassembled. or whether engine must be completely service that would eliminate abnormal noises, has been neglected.
disassembled for lower end repair. Most commonly only upper end
repair is needed (valves rings. p1stons. rtc.) a n d it is recommen ded INLET PIPE INLET PIPE NUT
procedure to first disassemble upper t>nd only. allowing engine base
to remain in frame. After d1sassembling upper end only. be sure to
•
inspe-ct connecting rod bearings for wear (par. 6). If connecting rod • •
bearings are worn and must be replaced, refer to chapter 3.
b. Emer~<'lll'~ Piston and Bing Senict'. Need of replacement
of rings, or poss1bly pistons and rings. is indicated by loss of normal
compression. loss of power, almormal oil consumption. excessive
exhaust smoke and piston slap or knock. W hen pistons develop exces-
stve clearance and slap due to wear or damage. and cylinders are
found worn more than 0.002-inch. smooth and true up cylinder bore
by honing, or boring and honing, to the next regular ovc>rsize piston
step. However. piston slap alone, dut' to wear and txcessivc cylinder-
piston clearance. does not mccssanly mean poor and undepc:ndable
performance A good compresSIOn stal is the requirement for good
performance. Good compressiOn d<·pcnds on smooth cylinders and
proper clearance between piston nngs and grooves.
c. Test fur Lf'aky \'ahf's and Worn Pi ~ton R i n~s. B efore
making th1s test. see that oil is in the tank. spark plugs arc tight.
cylinder head holts are tight, valve tappets have sufficient clearance
and that engine: is warm. It is difficult to determine whether valves
RA PO 3 10292
or rings (or both) are at fault when compreSSIOn is poor. In either
case. the cylinders must be removed to do a first class job. Figure 1- Removing Carburetor ancllntake Pipe A ssembly with
(I) COMPRF:SSION TEST. Operate engin e until it 1s thoroughly Wrench (41- W - 1570- JO)
warmed up and with the ignition switch off. crank the engine slow!~,
placing entire weight of the body on the starter crank. Engine com ( 1) UPPER END NotSES. Operate engine until it is thoroughly
pression should offer some resistance to the we1ght of an average' • Ill warmed up and idle engine from closed throttle to fast idling speed
rider before the starter crank passes through complete rang<' of 11 1 with vehicle standing. Listen for abnormal metallic noises that would
travel. If the engine offers little resistance to the starter crn nlc 111 indicate loose pistons, loose piston pins and possibly broken piston
testing either or both cylinders, it is an indication that comprr Nhl 11
rings. Operate vehicle on the road up to 25 or 30 miles per hour and
is not adequate in one or both cylinders. In vehicle operation Cn!Jhl
will lack power, overheat. fuel and oil consumption will b<' 1 1 r-11 I listen for metallic knocking sound that would be caused by loose
and engine performance will be sluggish in general. pistons, piston pins or loose r ings. Observe knocking (ping) in engine
when accelerating that would be caused by excessive carbon deposits.
d. Abnormal En~im· :\vise. Owing to constructionnl dr t.l~ 11 I NOTE: Spark control must be correctly adjusted and operated
the motorcycle (power and drive units are exposed) ccrt11111 tllf• 1t 1111
cal noises not noticeable in a motorcar or truck are evid~·nt 111 11•11111 II properly, to distinguish between c;!rbon and spark knocks.
8 9
I REMOVAL OF CYLINDERS AND PISTON ASSEMBLIES
cylinder nipples ; then remove carburetor and inlet assembly from
(2) ~NGINE BASE NOISES. Before attempting to diagnose enginr engine.
base n01ses, make sure that engine and transmission mountings 111 ,.
secure, front and rear drive chains are adjusted correctly, and vulv 1• c. Re movt> f.ylinde r Heads (fig. 2) . Remove spark plugs before
tappets have specified clearance. Operate engine from closed throttle· removing cylinder heads. Use special vvrench (41-W-1525) and re-
to fast idling speed and listen for abnormal metallic noise an tlw move cylinder head bolts. Remove bolt which secures cylinder head
vicinity of the crankcase and gear case. With vehicle in operation bracket to frame.
at speed~ from. 15 to 30 mil~s p_er hour, listen for thumping, poundm~. d. llemo,·e C)·linde r s. Clean crankcase around cylinder bases
or scrapmg no1se that may md1cate engine main bearing trouble. and valve covers to prevent dirt from entering cr ankcase when lifting
cylinders.
,\
(
•
I ,
.
0@
jt· ~ @@@@
J --;·----:._··... 4!'!..
HEAD BOLTS
AND WASHERS ~ E COVERS RAISE·D~ RA PO 310296
RA PD 310295
figure 3-Freeing Volve Covers with Wrench (41-W-3617)
figure 2-Removing Cylinder HeoJ Bolts with Wrench (4J-W-J525)
(1) Use valve cover wrench (41 -W -36 17) to loosen and unscrew
5. REMOVAL. lower valve covers (fig. 3). To faciltate lifting valve covers, and
a. Remove lnstrumt>nl Panel and Tanks. Refer to TM 9-87Q prevent damage to packing gaskets. use small amount of light oil
for instructions. around top edge of covers.
(2) Disconnect spark control wire at circuit breaker lever.
b. Removt' Carbure tor and fntake Pipe (fig. 1). Disconnt•ct
thr?ttle control wire at carburetor. Disconnect air intake 'l0!-1< (3) R emove nut and bolt from clamp securing front exhaust pipe
fittmg from carburetor and leave attached to hose. Loosen air host to right footboard side bar.
clamp at air_ cleaner and. remove hose with carburetor fittings. Rr (4) Use special cylinder base nut wrer .:h (41-W-872-10) andre-
move fuel hne and stramer from carburetor bowl. With specinl move all base nuts (fig. 4), except one on rear cylinder. While crank-
wrench (41 -W-1570- 10), loosen and unscrew inlet pipe nuts from
11
10
REMOVAL OF CYLINDERS AND PISTON ASSEMBLIES
ing engine to raise front piston, raise front cylinder <·nuu~to:h 111 plu
clean rag over crankcase opening. This will prevent dirt 111 ltiiY II"
END OF TOOL ... ...:r' "'
of broken rings from falhng into crankcase. Crank t ng1111 111 ho 11
front piston at bottom of stroke. then lift front cylindu upw ntl ultl
free of engine.
(5) R emove remaining stud nut from rear cylinder und t t: ltt ,y
rear cylinder in same manner front cylinder was removed
e. R e m ove Pistons. LOCK RING
( 1) Remove lock ring from slotted end of piston pin Slot p t ""' ' "
use of screwdriver blade underneath ring to pry and force tl u ll u (
FRONT CYLit-.JDI k RA PO 3102 99

ASSEMBLY
Figure 5-Removing Loclc Ring from Piston Pin, Using
Tool (4J- T- 3.260)
•
CYLINDER
BASE NUTS ~
./!:.1' .,.p U I'D :ti02f1
Figure 4 - Removing Cy linder Base Nuts with Wrench (4J- W-872- JO)
pin. Special tool ( 41- T -3260) will serve as a rest for the screwtldvt•t
(fig. 5).
(2) Use a soft drift slightly smaller (25,:1:! in. dia) than the pt~lon
pin and drift pin (with light hammer blows) out of piston, tnk1111t
care not to damage pin, piston bosses, or bend the connecting '"'' ·
b .
~ e;· .
·JI , ,..
.
•
..
'<.
6. INSP ECTION OF CON!\ECTI!\G ROD BEARINGS J.'C•~t

WEAR. Fi gur e 6 - lnspocting Connecting Rod lor Bearing Pla y
a . lnsp e<'l R o ds f or Up ami D own Play a nd U ppe r End S iclc•
S hake (fig. 6). When appreciable up and down play is found un d
12 13
CHAPTER 2
either or both rods have Ys inch or more side shake at extreme upprr OVERHAUL OF ENGINE IN VEHICLE (Cont'd)
end, the connecting rod roller bearing should be refitted. This requm·•
removing and disassembling engine. as outlined in chapter 3 Whc·n Section Ill
inspection finds rod bearings in good condition, or good enough for
considerably further engine service, proceed with .the upper end DISASSEMBLY, CLEANING, INSPECTION, REPAIR
service procedure which follows in section III of this chapter. AND ASSEMBLY
7. CYLINDER DISASSEMBLY.
a. Use spring lifter (41-L-1409) to compress valve springs and
remove split keys from ends of the valve stems (fig. 7). Valve spring
collars, valve springs, valve covers and valves can then be removed.
Mark valves so they can be installed in the same cylinders from
which they were removed.
8. CLEANING AND INSPF.CTJO:\ OF CYLINDERS AND

RELATED PARTS.
a.Cleaning.
(1) Clean outside of cylinder and head with wire brush to remove
dirt and rust, getting in between cooling fins as much as possible.
Use dry-cleaning solvent. CAUTION: Cylinder heads are cast of
aluminum and care must be exercised in handling and cleaning so as
not to break off cooling fins. Do not use any lye or other cleaning
solution that is harmful to aluminum.
(2) Scrape carbon from cylinder head, top of cylinder around
valves, top of cylinder bore above ring path and from inlet and
exhaust ports. When scraping carbon. be careful not to scratch or
nick cylinder a nd head joint faces, as a deep scratch may result in a
leak. Blow off loosened carbon. dirt, rust, etc .. with compressed air
and wipe cylinder bore and joint faces with a clean rag.
(3) R emove carbon a nd gum deposits from cylinder valve guides
with reamer (41-R-2309-65). See figure 8.
(4) Remove carbon deposits from cylinder valve seats.
(5) R emove carbon deposits and crust from va1ve head and stem,
using a knife and wire brush wheel. CAUTION: Never use a file or
other hard fool that will scratch or nick metal. Polish valve stem
lightly with very fine abrasive cloth or steel wool.
h. lnspe(•tion of Cylindf'rs (fig. 9) .
(1) BORE. Standard cylinder bore is 2.7445 to 2.7455 inches.
Cylinders must be accurately measured with micrometers for extent
of wear. By subtracting piston measurement from bore measurement
amount of piston-cylinder clearance is obtained. Bore measurements
of a used and worn cylinder should be taken Yz inch from top of
cylinder in ring path, measuring from front to rear where thrust
faces of piston bear.
(a) During a top overhaul. if cylinders are not scored and are
worn less than 0.002-inch. it is not advisable to refinish oversize at
that time. Do this operation at the next ..:omplete overhaul. How-
ever, in this case, if the total piston clearance i~ as much as 0.006
15
14
DISASSEMBLY, CLEANING, INSPECTION , REPAIR AND ASSEMBLY
inch, a new standard piston or a piston of the same oversize to which
the cylinder was last refinished should be fitted to reduce clearance
and obtain reasonably quiet C'peration.
(b) If, in completely overhauling engine and putting it in a
satisfactory conditio~ for a long period of further service, cylinders
show more than 0.002-inch wear, they should be refinished to the
next oversize step and fitted with new pistons. Refer to paragraph
11 of this section for sizes of oversize pistons and rings available.
(2) VALVE GUIDES. Standard stem-guide clearance is 0.0035 to
0.0055 inch. Clearance should not be allowed to exceed 0.008 inch
VALVE GUIDE REAMER
COVER
VALVE SPRING VALVE

LIFTER lA 'D 310304
SPRING Figure 8-Removing Carbon lrom Valve Guide with

Reamer (4J-R-2309-65)
hefore replacing guide, or possibly both valve and 6Uide. Valve guides
are pressed into cylinders.
COLLAR (3) VALVES. Inspect the valve stem for excessive wear. Standard
valve stem diameter is 0.339 to 0.340 inch. Valve warp will be indi-
KEY fJ '-\ cated when face is reground. Intake valves are marked "IN" on the
head and exhaust valves are marked "EX'' on the head.
( 4) CYLINDER VALVE SEATS. Valve seats, like valves. are subject
lA 'D J lOJ OJ to wear, pitting, and burning and should be refaced with cutter or
figure 1-Removing Valves with Spring Lifter (4J-l-J409) grinder each time the valves are refaced. As valves and seats are
16 17
DISASSEM8L Y, CLEANING, INSPECTION, REPAIR AND ASSEMBLY
refaced from time to time. the valve seats widen and the vulvt., wi ll badly worn or deeply scored are first r ebored to nearly the required
seat in a lower position when fully closed. Also, passage around vulvr oversize and then are finish-honed to exact size.
when fully open is somewhat restricted. T o correct this condlt "'"• (I) When refinishing cylmde-rs oversize, add the oversize step
cut additional clearance above valve seat so top edges of uuv.ul , apparently required to clean up bore to standard cylinder bore size;
valve face and valve seat match exactly. this gives the exact size to which cylinder should be refinished; ex-
(5) VALVE SPRINGS (fig. 10). Inspect each valve spring 10 lllltl ample: 2.745 inches (standard bore) plus 0.020 inch (oversize) equals
parison with a new one. lf free length of spring is 78 inch , 01 lc
.... l
.• •
.. •
• ' .,
. CENTERLINE OF BORf ·7
•
. .•
. • .. .
.I , •
' . .'
.-
. . •
•' ' .•
-•.
-..
- --· •
. .
•
..
. •
... •
.. . -.
-.•.
r. j
"'.. •
•
-·-..
-
• •
I '
• '
ItA 1'0 310111
Fig ure 9-Measuring Cyl inder Bore One-half I nch From Top, with Figure JO- Measuring Le ngth of Valve Springs
Inside Calipers {41-C-304)
2.765 inches (size to which cylinder should be refinished). Check
than length of new spring, replace with a new spring. New v 11 1vrl carefully with micrometers to be sure of refinishing to this size
springs will average 2 1%1! inches free length. Compression of 111 w (fig. 9). If this is accurately done. oversize pistons furnished in vari-
spring will be between 95 and lOS pounds when compressed 111 11 11 ous oversize steps will fit with normal clearance (0.001 S to 0.0025
inches. inch). Oversize pistons have their oversize stamped on their head;
for example: I 0, 20, etc.
9. REPAIR OF CYLINDER AND VALVES. b. ValvE" (;uides.
a. Cylinder. Cylinders can be refinished oversize either wit II n (l) If valve stem and guide clearanc·· exceeds 0.008 inch, press
hone only, or with a boring bar followed by a finishing hone. Cyl111dc 111 out guides and install new ones. Press or drift gnides out of cylinder
18 19
DISASSEMBLY, CLEANING, INSPECTION, REPAIR AND ASSEMBLY
from !nside of the valve chamber (fig. 11). Intake and exhaust valve
guides are interchangeable.
(2) Install new valve gu ·des by inverting cylinder and pressing
guides into guide hole until shoulder on the guide is tight against
the cylinder. New valve guides are reamed to correct size. H owever,
when guides are pressed into cylinders they may close up slightly;
also the ends may be burred . Therefore. after new guides are in place,
they should be sized and c leaned up with special reamer (41- R-2309-
65). Refer to figure 8. After installing new guides, valve seats must
be refaced to true them with the new guides.
PILOT GUIDE ,
•
CUTTER HOLDER
•
RA PO llOlU
figure 12-lncreasing Valve Passage with Cutter (41-C-2822-30) ,

Handle (41-H-2270) and Pilot Guide (41-P-412)
c. Valves. Valve face angle is 45 degrees for both intake and

exhaust valves, and valve rcfacing grinder must be adjusted exactly
to this angle. It is important not to remove any more metal than is
GUIDE REMOVED necessary to clean up and true valve face. If grinding leaves the
width of valve edge 1 !.1 ~ inch or less, at the thinnest p lace, use a new
valve. If the end of the valve stem shows uneven wear, true the end
of the stem on a valve refacer, using V-block provided for that
purpose.
d. Cylinder Valve St-at". When a new valve guide is installed,
lA PD :UOJ06 it is not likely to have exactly the same relation that the old guide
Figure lr-Removing Valve Guides had to valve seat. Therefore, it is especially important, after fitting
new guides that seats be carefully refaced to make them concentric
20
21
with a screwdriver, just enough to give valve face and seat a lapped
with guides and assure perfect alinement and matching of valvr 1111 fl finish.
and valve seat. NOTE: Remove no more metal than abso/ufr/1 (b) Tes ting Valve Seat for Trueness. Remove valve, wash valve
necessary to clean up and true valve seats. face and seat thoroughly with clean gasoline and dry with compressed
(1) CORRECTING VALVE SEAT CLEARANCES (fig. 12). As vnlvrll air. T est seat for trueness by making pencil marks about Ys inch
and seats are refaced from time to time, the valve seats wide-n 1111d apart all around the face of the valve: then place valve in guide and
the valves seat in a lower position when fully closed. Passage 111 mtnd put considerable pressure on the valve head with a large screwdriver,
the valve. when fully open, would be somewhat restricted. Ccu 11 t 1 at the same time giving it a slight b ack-and-forth motion. Remove
this condition by using clearance cutter (41-C-2822-30) to remuvr the valve to examine the face and observe how the pencil marks have
metal so that top edge of angular valve face and the cylinder sent been erased. Pencil marks should show that the valve and seat faces
are bearing all the way around for a perfect job. If lapped finish is
not complete around either the valve or the valve seat, further seat-
ing is required.
-
I ·~
--
'
VAlVE KEY REPLACER
.
'
•
,
VALVE SPRIN , .... t
LIFTER THICKNESS GAGE
llA PO 310312 ~
RA PO 310307
figure 13-lnstolling Valve Stem Callar Keys, Using Lilter (41-L-1409)

and Replacer (41-R-2398)
I figure 14-Measuring Ring Clearance in Piston Groove
10- CYLINDER ASSK'\HtLY.

match perfectly. Use clearance cutter with handle (41-H-2270) oncl a. Locate marked valves in their respective cylinders. taking care
pilot guide (41-P-412). to install intake valves (marked " IN") in chamber nearest intake
pipe opening, and exhaust v alve (marked "EX") in chamber nearest
(2) GRINDING AND TESTING VALVE SEATS. Intake and exhiHIIol exhaust port.
valves lire made of different materials and must not be interchnn~tl'tl
h. Locate spring cover asbestos gasket on the valve guid(' and
when seating. Intake valves are marked ''IN" on head; exhaust vnlvc 11
are marked "EX." install upper cover. composition gasket, and lower cover.
c. Install valve spring and colla r over valve stem and compress
(a) Valve seats and valve faces that have been smoothly 111\fl
spring with lifter ( 41-L-1409) enough to install the split valve stem
accurately refaced with grinders, wiJl require very little grindinl( 111 keys in -valvt' stem groove, small end of ~o ne upward, with replacer
lapping to complete the seating operation. Apply a light coat of fillt' {41-R-2398) (fig. 13).
compound to valve face. Insert valve stem in guide and oscillate it
23
22
center line of piston pin. Piston clearance (standard or oversize) in
cylinder is 0.0015 to 0.0025 inch. If a fit within these limits cannot
be obtained with facilities at hand. it is preferable to allow more
clearance rather than less. Check inside and outside micrometers
' together to make sure they read exactly the same for correct piston
and cylinder clearance fitting measurements. Do not "squeeze" the
piston skirt with the micrometers and obtain a false m easurement.
' c. Disassembly of Piston. Remove piston rings with thin strips
of metal, taking care not to scratch or damage piston surface.
d. Cleaning and Inspection (figs. 14 and 15). Remove carbon
deposits from top of piston, exercising care not to cut or nick the
aluminum. Clean the ring grooves free of carbon and gum deposits.
Any excess of carbon or sludge accumulation on inside of piston can
be removed with dry-cleaning solvent.
~
RING GAP
THICKNESS GAGE
l I PISTON
-- .....
I I
lA PD JIOllt
Figure JS-Measuring Piston with Micrometer Calipers (41-C-307)

RA PD 310309
d. Release pressure on spring compressor to engage valve sprin&

collar and valve stem key. - - - Figure J6-Measuring Piston Ring Gaps
e. Repeat above procedure for each valve and spring assembly. I (I) Inspect piston for cracks, scored, cut, or damaged surface.
Place standard ring in ring grooves and with a feeler gage, measure
11. PISTONS, PISTON PINS, AND RINGS. clearance. Maximum p ermissible side clearance is 0.008 inch (fig. 14) .
If piston ring grooves arc worn to give more than 0.008 inch side
a. Pistons. Pistons are special taper-cam ground· the diameter nt
clearance, replace piston.
the top of the skirt (just below bottom ring) being 0.0025-inch smollrr
than at the bottom of the skirt. Two horizontal slots one front nnd (2) Measure piston at bottom of skirt, front to rear and at right
o':le rear, are cut in th~ bottom ring groove. NOTE:' Large ovcr:M~t< angles to piston pin hole (fig. IS). If piston and / or cylinder are worn
ptstons are slotted hortzontally and also have a vertical slot in or~n to give more than 0.006 inch clearance, piston must be replaced (par.
thrust face. All pistons (standard or oversize) obtained from thr 8 h (1) (a) and (b)).
m.anuf?-ctur~r are furnished with a piston pin correctly fitted ond (3) Oversize piston rings are available in steps of 0.010. 0.020,
wtth nngs. mstalled. o.versize pistons in steps of 0.010, 0.020, o.OJO, 0.030, and 0.040 inch.
and 0.040 mch are avadable and are stamped " 10," "20," etc. e. Fitting Nt>w Rings to Cylinder. It is recommended that piston
h .. Pi~ton Cl~rance in Cylinder. Standard piston size at bottorn rings be replaced each time the old rings are removed from the piston,
of sktrt IS 2.734 mch, measured front to rear and at right angles to or at each top overhaul.
24 25
- -
a nd rod upper bushing must be honed or reamed accordingly. Over-
i I size piston pins are available in steps of 0.002 , 0.004, 0.006, 0.008, and
0.010 inch.
RING GUIDE STRIPS
- g. Installing R in gs o n Piston. Wh~n n~w rings are being in-
l I stalled, exercise care in properly locatmg nngs on the piston as
follows:
(1) Compression rings (plain) are installed in the two upper
piston ring grooves.
(2) Oil control ring (channeled) is installed in the lower piston
ring groove.
• •
I. I .
- ~
. I
-·
figure J7-Removing Piston Rings RA PD 310292
(1) T o inspect ring gap, p lace a piston in cylinder with bottom Figure J8-lnstolling Connecting Rod Bushing, Using Tool (4J-T-3305)
and Tool (4J-T-309J)
end of piston about % inch from end of cylinder (fig. 16). Set the
ring to be inspected inside the cylinder a nd squarely against the
piston. Use a set of thickness gages and determine the ring gap. (3) Use thin pieces of soft m etal to guide and slip the ring.s over
N ormal ring ~ap is 0.010 to 0.020 inch. Even though t he ring gap may the piston into their respective grooves witho~t over~xpandmg or
twisting the rings and damaging the fi nely fimshed piston surface
be slightly greater than these limits, only standard size piston rings
(fig. 17).
should be used in the cylinder u nless the cylinder has been reground.
( 2) If cylinder has been reground, la pped or h on ed oversize, t h en 12. FITIING UPPE R END CONNECTING ROD BUSHING T O
use the correct oversize rings, fitting r ings to give gap clearance o f PISTON PIN.
0.010 to 0.020 in ch . If gap at ring en ds is less than 0.010 inch, ring
ends m ay butt together u nder expansion and rings may be scored or a. Fitting Rod Bushing to Pis ton Pin ( fig. 18). R eplace c~nnec~
b roken . Gap may be increased by filin g the rin g ends w ith a fine-cut ing rod uppe.- end bronze bushing because of wea~ ~nd excessive pm
fl at file. clearance or looseness in rod. I nspect for both cond1tlons. W hen bush-
ing is found tight in rod but is worn to excessive pin clear~nce (0.002
f. Fitting Pist o n Pin to Piston. N ew pistons a re fu rnish ed with inch or more) it is possible to service it b) reaming overs1ze and fit-
standard size pins correctly fitted to piston bosses. P in is a light, hand - tin g an oversize pin . H owever , it is better p ract;ce to install a new
press fit in p iston bosses. If oversize pin is used; then piston bosses
27
26
bushing and r eam and hone it to fit a standard pin, except wht n PAPER TEST ST RIPS
p iston to be used has previously been fitted with oversize p in or Pill \
is loose in bosses. necessitatmg fitting with larger pin. The princ1pal '•
objection to fitting the rod upper end oversize is tha t , in the ev~nl of
emergency field service requiring quick fitting of pistons, considerAbly
more time is required for the job if upper end b earing is overslll'
N ew pistons are fitted with standard size pins, and installing one is
a short job if the rod bushing is already reamed to standard size. If
bushing has been reamed ov ersize, either new bushing must be in-
stalled and reamed to standard size, or piston must b e reamed over-
size to fit an oversize pin, which involves extra time.
(I) When renewing bushings in connection with only a top ov er-
haul, use special bushing tool (41-T -3305) and rod holding fixtu re
PISTON PIN • PUSHING LOCK INTO PISTON PIN

LOCK RING GROOVE WITH SLEEVE
•
RA PD 310290
RA PD 310376
SPLIT LOCK RING IN CORRECT B FORCING SPL IT LOCK RING INTO Figure 20-Checking Connecting Rod Alinement with
POSITION ON TAPER OF TOOL PI STON PIN GROOVE Sq uaring Pla te (41-P-1550-25)
WITH TOOL SLEEVE
Figure 19-lnstalling Piston Pin Lock Ring w ith Tool (41-T-3260) (2) To facilitate installing piston pin, heat piston (but not pin)
about as hot as it can be handled.
(41-T-3091). Ra ise rod just enough to give clearance for bushing (3) W ith piston pin in p lace and one lock ring ·already in its
tool when rod is held in holding fixture (fig. 18). B e careful to start groove, install the remaining lock ring. CAUTION: Always use a
new bushings with bushmg oil slot in alinement with oil slot in rod. new piston pin lock rin~. Use special tool ( 41-T -3260) to install nng,
thus prevent overexpanding with consequent damage to the lock ring
(2) Ream n ew bushing nearly to size a~d finish to exact size with (fig. 19). Be sure that lock nng seats firmly in its groove because a
special hone (41-H-2382). A properly fitted pin should have 0.001 lock ring loosely inst alled will rapidly loosen further in service and
inch clearance; with this clearance, pin will have just noticeable finally come off of the pin. resulting in p1ston and cylinder damage.
sha ke in bushing. A tighter fit is likely to result in a "seized" pin, or
bushing may become loosened in rod.
14. ALII\E CON~ECTJI\G RODS.
13. li\ STALLING PISTONS 0~ CO!'iNECTII\G RODS. a . Alining Pistons ancl Connectin~ Rods. When refitting and
reassembling connecting rods and finally fitting pistons, rods may
a. Insta ll Pis to n s. possibly be bent or twisted. throwing upper bearing and lower bear-
( 1) Standard pistons with horizontal slots only may be fitted ing out of alinement with each other to some extent. Therefore, after
with either thrust face to the front. Large. oversize pistons with pistons h ave been fitted, rods must b~ checked and realined if neces-
v ertical slot in one thrust face must be fitted with that thrust f ace sary. If a rod is bent or twisted, piston has a cocked relation to
to the front. 29
18
cylinder bore and the result is excessive noise and rapid wear. Con- piece of paper, then the other, partially from underneath piston. In
m·cting rod alin ement is determined by seating o f piston skirt end on removing the paper, one of two things will happen: both will have
a special thickness surface plate (piston squaring plate) placed on the ~a111:e amount of drag, or one will be free and the other tight. If
c~a nkcase cylinder base face (lig. 20). The flywheel crankpin posi- one IS tighter than the other, remember which side of the engine the
tions, for~ard and ?ackward, in relation to the piston position on tight piece of paper was on; then turn engi ne so that flywheel locates
the squanng r:>late mfluence the seating of piston on the squaring the crankpin in the other position and repeat the "paper check"
plate and mdtcate whether or not the connecting rod :s in aline procedure. Behavior of paper in making connecting rod alinement
ment. Flyw.heels ':fl~st be rotated fo~ward and backward to change check will reveal either of the four conditions as follows:
the crankpm postttons when checkmg piston and connecting rod (1) CONNECTING Roo IS IN ALINEMENT. When the connecting
alinement. rod being checked is in perfect alinement, the pieces of paper under
b. Installing Pistons on ConneCting Rods. See paragraph 13. pist.o? will have the same amount of drag in both flywheel crankpin
poSitiOnS.
(2) CONNECTING Roo IS BENT. If the connecting rod is bent, only
one of the pieces of paper (on the same side of the engine) will be
. - ALINING BAR IN PISTON PIN HOLE
free wh~n check has been made in both flywheel crankpin positions.
To repatr, refer to step e of this paragraph.
(3) CONNECTING Roo IS TWISTED. This condition will cause the
•
hi~h, or loose pap~r side of a piston (on one side of the engine) to
-- ~htft to the other stde of the engine as the flywheel crankpin position
IS changed. Locate flywheel in one crankpin position and make "paper
check" and note which side of engine the loose piece of paper is on:
then rotate fly.whe~l to the other crank position and the piece of paper
on the oppostte Stdc of the piston will be found loose. To repair
refer to step f of this paragraph.
(4) CONNECTING Roo IS BENT AND TWISTED. This condition will
c~use both pieces of paper to be tight (or nearly so) under the piston
wtth flywheel crank in one position, and when the flywheel is
--- ,_
• rot~ted to the other crank position, one of the pieces of paper will be
qmte free. Remember which side of engine the tight piece of paper was
on, as well as the flywheel crank position, and refer to step g of this
~ ·- -., paragraph for repair.
... ..
:~
~
I -
e. S trai~htenin~ a Bent CcmnP.etin~ Rod (fig. 21 ). Insert a
' / ~:
'
;• I 91 •
·, ,6-mc h d'•ametcr rod through the piston pin hole. on the low side of
the piston, and apply upward force to straighten the rod. R echeck
SQUARING PLATE alinement after each straightening operation. NOTE: Raise piston
to highe~f position, before straightening a rod, to prevent damage to
Figure 21-Stroightening Bent or Twisted Connecting Rod piston skirt.
c. Locatio~ Squarin~ Plate on Crankc•a!>c>. Make sure crankcase f. Straightenin~ a Twistl'cl Conrwctin!! Rod . Insert straightening
cylinder base face is clt"an and free frum burs so that piston squaring bar through piston pin hole. on the high side of the piston, and pull
plate (41 -P - 1550-25) scats firmly and squarely on crankcase for away from the crankpin position. Example: Inspection shows that
accurate inspection. Also see that skirt end of piston is not nicked or rod is twisted, and with crankpin in forward position, the piston is
damaged. Alincment inspection must be m ade for each connecting high on the right side (gear case sirle). Straightening bar force is
rod and piston. applied on the right side of the piston. pulling away (toward the
rear) from crankpin position.
cl. Cht>~king Al.ine':"ent with Tissue Paper (fig. 20). I nsert
narrow ~tnps of thtn ttssue paper (not wider than % inch and of ~· Strai!! hlf'nin~ a Bent ancl Twisted Connt>('tin~ Rod. This
equal thtckness) underneath piston, one piece of paper on each sidt· is a combination of a bend and twist and the bend must be removed
and directly below (in line with) the piston pin. Press piston down first. With the flywheel crank located in the position that caused the
lightly with finger tips resting on center of piston head. With piston piston to be low (tight paper) on one sitie, insert the straightening
located on squaring plate in one crankpin position, first pull one bar through piston pin hole. on the low side, and apply upward force
30 31
CHAPTER 2
to straighten the rod. After the bend has been removed, then th< tWI 1 OVERHAUL OF ENGINE IN VEHICLE (Cont'd)
can be removed as outlined in f above. Recheck alinement aftl·r c nd1
straighten ing operation. Section IV
h. ln s pectin~ Connec ting Rods for Center Alinement. Altr.1
rods have been alined, inspect to see that pistons center in crnnlll , , INSTALLATION
cylinder open ing, without side pressure on rod upper ends. If Ill 1
ends are off center enough to prevent pistons from centering, t hf'y 15. 1:\ST.-\LLA TION.
must be corrected by replacement of flywheel thrust washers of c 'I" 11 a . Install Cvlinder Assemhli.-s.
thickness or by replacement of flywheels.
(I) Lubricate cylinder walls, pistons. pins, and rod upper bush-
ings generously with engme oil. Space ring gaps about equidistant
around piston but do not locate any gap near exhaust valve port, as in
this position ring ends may be overheated and burned.
(2) Turn engine until crankpin is at bottom center. See that
crankcases are clean and fit cylinder base gaskets. See that v alve
cover gaskets on tappet guides are a ll in p lace and in good order. If
any are damaged or broken. replace them. Cylinders with valves and
valve covers assembled can now be installed over pistons and rings,
being careful not to change ring gap location. W ork cylinders care-
fully down over rings to avoid any possibility of ring breakage. In-
stall rear cylinder first and as cylinder seats, turn engine so tappets
are at their lowest position. Install cylinder base nuts and pull them
down just snug. (This is to allow alinement of iotake pipe when
installed.) Follow same procedure with front cylinder. Do not screw
down valve covers until tappets have been adjusted (par. 16 a ). In-
sert exhaust pipes into cylinders as they are seated.
(3) Attach front exhaust pipe clamp to footboard side bar.
h. Install Carbure tor a nd Intake Pipe.
(1) Inspect intake manifold packing bushings to see that they are
in good condition. Assemble nuts and bushings to manifold after
applying a light coat of oil or grease so bushings will freely adjust
themselves to manifold a nd cylinder nipples as nuts are tightened.
Install nuts on cylinder nipples and tighten securely (wrench
41-W-1570-10). R efer to figure 1. Unless manifold packing bushings
are in good condition and manifold nuts securely tightened there are
likely to be air leaks around manifold-cylinder points. With this
condition it will not be possible to get a satisfactory low speed
carburetor adjustment.
(2) After manifold is tight, loosen cylinder base nuts slightly to
allow final shifting and lining up of cylinders and manifold. then
tighten base nuts securely with wrench {41-W -872- 10) .
c. Cht'ck J~nition Timin~. With cylinder heads removed,
ignition can be timed acc-urately by piston location as follows:
(1) Turn engine until front piston is coming up on compression
stroke (directly after front cylinder intake valve closes).
(2) R emove circuit breaker cover and advance spark lever by
turning left handlebar grip inward as far as it will go. Spark lever
should be inward as far as it will go and. if necessary, adjust control
wire to obtain this position.
32 33
INSTALLATION
(2) M ake sure tops of cylinders and cylinder h ead faces are
PISTON COMING UP ON COMPRESSION STROKt
clean. Apply a light coat of engine oil or grease to both sides of
gaskets and install gaskets.
(3) P lace heads on cylinders and install heavy washers and head
bolts. Attach cylinder h ead bracket (top mounting bracket) with the
two long bolts, spacers and flat washers. Spacers go between the
cylinder heads and bracket. A flat washer goes under toe head of each
long bolt above bracket. Some engines have fla t washers between
spacers and bracket.
(4) Secure engine top mounting bracket (cylinder head bracket)
to fra me lug, installing required number of thin shim washers, to-
gether with clamp for front spark pl ug cable. to fill space between
bracket and frame lug before tightening bolt. NOTE: Frame Jug must
be free from paint or ~rease to make clean e!ectrical conn ection with
plated shim washers and mounting bracket lor adequate radio bondin~.
(5) H ead bolts must be tightened evenly to attain a tight joint.
First turn bolts d own just snug: then tighten each of them one-eighth
to one-quarter turn at a time until all are securely tightened. Use
special head bolt wrench (41 -W-1525). If torque wrench is available,
tighten head bolts to 60 foot-pounds minimum, 65 foot -pounds maxi-
mum tension when engine is cold.
(6) Install spark plugs (use new gaskets if old ones are in bad
condition) and tighten securely. Attach the high tension cable
terminals.
e. Install Tanks, Instrument Panel, Air Intake Hose, and Fuel
• Pipe. Install tanks as described in TM 9-879. Install instrument
panel as d escribed in TM 9-879. Attach air hose to air cleaner and
secure hose fitting to carburetor with four screws. Tighten air hose
ADVANCED
clamps. Attach fuel strainer and fuel pipe to carburetor and tank
,L
-
fuel supply nipple. Open tank fuel supply valve and inspect fuel line
•
-
and connection for leaks.
RA ,0 :J10366
Figure 2 2- Timing Ignition by Piston Location
. (3) . T~~n ~ngine in direction in which it runs until front cylinder

ptston ts ,~2 t~ch ~efore top d ead center on the compression stroke
(fig: 22). At ~hts pomt, the small end o f the ignition timer cam should
be JUS.t opemng the points. N O TE: Point ~ap must be adjus ted to
0.022 mch before correct in~ ignition· timin~.
~ 4) . To correct ignition timing, loosen timer lever band screw and
~hlft t1mer head until points just open with front piston set at n 1.,
mch befo~e ~op dead center; then tighten timer head band scn·.:V
Recheck tn~ung after timer head band screw has been tightened lo
make sure ttmer head has not shifted. J
d. Install Cylinder Heads.
<.I) Use a new cylinder head gasket each time heads are installed
Thts assures leak-free joints. Old gaskets should be reused only in an
emergency when new gaskets arc not available.
l
34 35
ADJUSTMENT AND TESTS
CHAPTER 2 ( 4) Turn down valve spring covers with special wrench
(41-W-3617).
OVERHAUL Of ENGINE IN VEHICLE (Cont'd)
h . Carburetor Con trol (:ig. 2 5). Adjustment for full opening and
Section V closing of throttle to correspond with full inward and outward motion
of the handlebar grip is made at the junction of the control wire end
ADJUSTMENT AND TESTS and the throttle lever connection.
( 1) Enter end o f control wire in throttle lever connection hole.
16. ADJUSTMENT. Turn right handlebar grip outward as far as it will go: then turn it
a. Valve Tappets. Valve tappets must be adjusted after valve inward slightly. Holding throttle grip in this position, move throttle
grinding before attempting to start engine. Inlet valves are those lever forward against its stop (closed position) and secure wire in
nearest carburetor intake pipe. connector block with clamp screw. Check closing of throttle after
(1) Make sure each tappet is at its lowest position by turmng
engine ahead until like tappet in the other cylinder is at its highest ..
position (valve fully open).
• Figure 24- Tightening Valve Spring Covers with

Wrench (41-W-3617)
'
~ -·-
tightening control wire set screw. If necessary. reset the control wire
Figure 23-Adjusting Valve Tappets with Wrenches (41-W-3572)
in the connector block until throttle is closed with full outward move-
ment of the right grip.
(2) After loosening adjusting screw lock nut, turn tappet adjust-
ing screw as necessary to obtain specified tappet clearance (fil&. 23). (2) Check full opening of throttle by turning right grip inward
Inlet valve stem and tappet clearance is 0.004 to 0.005 inch. Exhaust as far as. i~ will go and see that throttle lever is against its stop (full
open pos1tlon). If necessary reset the control wire in connector block
valve stem and tappet clearance is 0.006 to 0.007 inch. Measure with
until full open and closed positions are obtained.
an accurate thickness gage. After obtaining correct tappet clearance,
tighten adjusting screw lock nut. Inspect tappet clearance after c. Car~uretor Adjustment (fig. 25). A carburetor that is badly
tightening lock nut because adjustment sometimes changes when nut out of adJustment, or a new carburetor just installed, must be ad-
is tightened. Readjust if necessary. justed as follows:
(3) See that paper gasket between valve cover and tappet guide (1) Turn the low speed needle valve (on rear of carburetor body)
is in good condition. If broken or damaged, install a new gasket to all the way down (to right); then back it out (to left) about three
full turns. With needle valve in this position , engine will start, but
prevent an oil leak.
mixture will probably be too rich.
36
37
ADJUSTMENT AND TESTS
(4) Engine starting and all -around carburetion will be better
THROTTLE CONTROL with low speed fuel adjustment slightly rich rather than extremely lean.
LEVER WIRE (S) If engine idling and low speed a djustment is difficult to
obtain, inspect inlet pipe nipple connections for air leakage. Apply
a few drops of gasoline around nipple nuts with engine idling and
I
I •
observe action on engine operation.
d . S park Control. Spark retard and advance is controlled by left
handlebar grip. Spark lever operates within a quadrant mounted on
engine. Spark must b e fully advanced (lever inward toward engine)
when left grip is turned inward to full extent of its travel. When grip
is turned outward, spark lever retards (lever outward, away from
engine).
(1) Loosen spark control wire clamp screw at spark lever and
turn left grip fully inward ; then back it o ut just a little. H olding grip
in this position, shift spark lever inward toward engine as far as it
will go; then tighten control wire clamp screw. Test by turning left
grip fully inward and noting position of spark lever. Spark lever
should be against inner side of quadrant. R etard spark and check
•
position of spark lever. It should be against outer side of quadrant.
/ ../ (2) Readjust as n ecessary for full a dvance and retard of timer
lever positions when left grip is turned inward and outward respec-
tively.
lA PD 310409
LOW SPEED THROTTLE 17. ROAD TEST.
ADJUSTING LEVER a. General P e rformance. R oad test vehicle for general perform·
NEEDLE STOP SCREW
ance, giving attention to adjustment of chains, action of clutch and
gear shifter controls and brakes. Engine newly fitted with pistons
figure
•
25-Carburetor Control Lever and Low Speed Needle Valve and / or rings should be operated not faster than 30 miles per hour for
the first 100 miles; 35 miles per hour for the next 300 miles and 40
(2) Start engine and, after choke lever has been moved to normal miles per hour for the next 400 miles. Avoid running at or near top
open run ning position and engine is normally hot, correct adjustment speed for long distances du ring the first 1,000 miles.
of needle valve by turning needle valve down (to right) one notch at (1) Observe action of panel signal lights for generator charging
a time until mixture becomes so lean that engine "misses" and is rate and engine oil pressure.
inclined to stop; then back out (to left) n eedle valve 5 to l 0 notches
(2) Observe engine performance with regard to carburetor ad-
or until engine fires regularly with spark advanced and throttle
justment with vehicle in operation.
closed (or as nearly closed as it can be set and still have engine run
at idling speed). (3) Observe pulling power of engine at low speeds and its ability
to accelerate when throttle is opened.
(3) Adjust engine idling speed by means of throttle lever stop
screw with throttle in fully closed position. Turning stop screw to (4) Watch for excessive engine heating.
right makes engine idle faster, and turning it to the left makes engine (5) Look for oil leaks around cylinder heads, cylinder bases,
idle slower. NOTE : Do not idle engine at slowest possible speed valve covers and spark plugs.
because an extremely slow idling adjustment causes hard engine b . Noises. While road testing vehicle, listen for unusual noises
starting. Changing engine idling speed with throttle lever stop screw in engine, clutch. transmission, wheels, and other members tha t might
is likely to change the low speed fuel mixture to some extent; there- indicate developing trouble.
fore , it will be n ecessary to again check and correct the low speed (1) Listen for engine knocking when pulling at medium speed,
needle valve adjustment (see (1) above). considering spark knock which should cease when spark is retarded.
38 39
CHAPTER 2
OVERHAUL OF ENGINE IN VEHICLE (Cont'd)
(2) Listen for pounding, thumping noises in engine, considering
the usual timing gear noises. NOTE: Do not confuse scrapin~, pound Sedion VI
in~ noise caused by excessively loose front drive chain with en~ine
internal noise. FITS AND TOLERANCES
(3) Check for unusual vibration that may be caused by loose
engine mounting or loose transmission mounting (also causes thump- 18. FITS AND TOLERANCES.
ing noise).
a. The following table of fits, tolerances, and spc:cifications covers
{4) Locate and remedy any rattles and squeaks caused by loose, upper end items pertinent to repair of engine in thc'vehicle.
broken, or dry chassis members.
{1) CONNECTING Roo PISTON PtN B CSHING. Standard hole di-
ameter, 0.7925 inch. Standard ptston p in in connecting rod bushing
clearance is 0.001 inch. Ream and hone for ov ersize pin when clear-
ance exceeds 0.002 inch. R eplace to accommodate new piston fitted
with standard pin.
(2) CONNECTING Roo UPPER END SIDE PLAY. To determine
condition of connecting rod roller bearings, shake top end of rod
sideways and when either or both rods have Ys inch or more side
shake, lower end bearing must be repaired.
(3) CYLINDER BORE. Standard bore is 2.7445 to 2.7455 inches.
When wqrn 0.002 inch or more, larger than standard or an oversize
bore, refinish cylinder.
(4) CIRCUIT BREAKER POINT GAP. 0.0022 inch when points are
held open at highest point on timer cam.
(5) IGNITION TIMING. Circuit breaker points just starting to
open when piston is Y4 to %2 inch before top dead center, coming up
on the compression stroke.
(6) PISTON-CYLINDER HEAD CLEARANCE. The distance between
cylinder head and piston (at highest position) is l,i 6 to 33 2 inch.
(7) PISTON. Standard size is 2.743 inches measured at bottom
of the skirt, front to rear, at right angles to center line of pin.
(8) PISTON CLEARANCE IN CYLINDER. The piston must have
0.0015 to 0.0025-inch clearance in the cylinder (standard or oversize).
(9) PISTON SIZES AVAILABLE. Standard and 0.010, 0.020, 0.030
and 0.040 inch ovcrsizes available. Oversize pistons stamped on top
"10," "20," etc.
(10) PISTON RING SIDE CLEARANCE IN PISTON GROOVES. Standard
dearance 0.004 inch. Maximum allowable clearance before new ring
(or piston) is necessary 0.006 inch.
(11) PISTON RING GAP. New rings must have 0.010 to 0.020-inch
gap in cylinder.
(12) PISTON RING SIZES AVAILAAI.E. Standard and 0.010, 0.020,
0.030 and 0.040 inch oversizes are available.
(13) PISTON PIN. Standard size 0.7915-inch diameter. Replace
when worn 0.0005 inch.
(14) PISTON PIN FIT IN PISTON BOSSES. Light hand press fit in
piston.
41
40
CHAPTER 3
(15) PISTON PIN CLEARANCE IN CONNECTING ROD B uSHlNO.
0.001 inch. Refit when pin and bushing clearance is in excess of'0.002 ENGINE
inch.
Section I
(16) PlSTON PIN SIZES AVAILABLE. Standard and 0.002. 0.004,
0.006, 0.008 and 0.010 inch oversizes. ENGINE DISASSEMBLY INTO SUBASSEMBLIES
(17) VALVE STEM IN GUIDE CLEARANCE. 0.0035 to 0.0055 inch.
Replace valve and or guide when clearance exceeds 0 .008 inch. 19. PHELI\11!\AHY lt\~TRUCTIO!"S.
(18) VALVE SPRINGS. Free length of a new intake or exhaust
a. En~int' n('rllOYal. Refer to TM 9·879.
valve spring is approximately 21 ~;1 :! inches. R eplace when shrunken
more than Ys inch. b. \1nunt En~ine on Stancl. A strong wooden box with an open-
(19) VALVE TAPPET CLEARANCE (engine cold). Intake valves, ing about 8 x 8 inches and at least 4 inches deep can be used to
0.004 to 0 .005 inch. Exhaust valves, 0.006 to 0.007 inch. support engine (fig. 26).
RA 'D 310294
Figure 26 -Engine Mounting StanJ
c. Remove Accessories. Refer to TM 9·879 for removal instruc-

tions for the following accessories: carburetor, generator, spark plugs,
relay and circuit breaker assembly.
d. Cit-an Exterior of Engine. Plug all openings to the interior
of the engine, and remove all dirt and grease with dry-cleaning sol-
vent or steam-cleaning equipment.
20. DISASSEJ\IBLY.
a. Engine Disassembly Sequenl.'e. The sequence in engine dis-
assembly is as follows: cylinder heads, cylindP.r assemblies, piston
42 43
ENGINE DISASSEMBLY INTO SUBASSEMBLIES
~ ·.
·~
•
I ;-·~ ,,
~:J·
~~
~· r-----
I
-
RA PD 310415
Figure 21-Removing Oil feed Pump . ""'· -·~
~ 0 BREATHER VALVE
0 0 ~ AND SCAVENGER
8 e 8 e PUMP AssEMBL v
PUMP NUTS AND WASHERS RA PD 310311
figure 29-Removing Scavenger Pump and Breather Valve Assembly
assemblies, oil feed pump, gear case cover, scavenger pump, timing
gears, crankcases and flywheels.
b. Ord.-r and Care of Compont>nls. Keep all components of
individual engine in one box or pan and exercise care in handling of
parts to prevent loss and damage.
GEAR CASE
c. Disassembly. InstruCtions and references to instructions perti-
nent to engine disassembly follow:
COVER
(1) REMOVE CYLINDER HEADS. See paragraph S <'.
(2) REMOVE CYLINDER ASSEMBLIES. Refer to paragraph 5 d .
(3) REMOVE PISTON AssEMBLIES. See paragraph S e.
(4) REMOVE OIL FEED PUMP (fig. 27). Remove the hexagon head
screw and three nuts and feed pump can then be pulled off of gear
' l &' ' ' ' 'L' ~ER

case cover. CAUTION: Unless a new gasket is available, be careful
SCREWS not to damage the old one as this is a very special gasket concerning
RA PD 310310 both thickness and location of holes for oil channels.
Figure 28-Removing Gear Cose Cover 45
44
(5) REMOVE GEAR CASE COVER (fig. 28). If tappets and guides PULLER TOOL
must be replaced, perform operation under (8) below before removing
gear case cover. Remove all remaining gear case cover screws. Use a
-
hammer and a block of wood (tapping lightly at the ends where
cover projects beyond the gear case) to drift cover free from register-
ing dowel pins. NOTE : Do not use a screwdriver or other sharp tool
I j
inserted between joint faces to remove cover. The thin steel shim
washers installed on outer ends of front cylinder cam gears may come
off with the cover; be careful they are not lost. Take care, also, to
protect cover gasket as this is a very special gasket concerning both
thickness and location of holes for oilhole channels.
APPFT ASSEMBLY
CAM GEAR
SHAFT SHIMS
REAR
EXHAUST
CAM
REAR INLET GUIDE SCREWS
CAM GU IDE
AND WASHERS
~
FRONT
~...\ ~
INLET CAM IDlER GEAR
FRONT
0
0 WASHER
EXHAUST CAM tOCK RING U PO 31 0325 COVER
RA PO 3 10313
Figure 30-Removing Timing Gears with Puller (41-P-2903)
Figure 31-Removing Tappet Guides w ith Puller (41-P-2956)
(6) REMOVE SCAVENGER PUMP AND CRANKCASE BREATHER
VALVE ASSEMBLY (fig. 29). Remove four nuts and this assembly can be located between gear hub faces and crankcase. Remove pinion
be pulled off the four mounting studs, out of crankcase gear c'hamber. gear, breather valve and scavenger pump drive (worm) gear, bearing
Crankcase breather valve is an integral part of the scavenger pump. seal ring spring and gear shaft bearing oil seal ring from gear shaft.
CAUTION: Take care not to lose the screen located between breather Gears are a slip fit on shaft spline and should slip off of shaft
valve and crankcase port when pump assembly is removed. easily. If gears are difficult to remove from gear shaft, use puller
(7) REMOVE TIMING GEARS (fig. 30). Remove front and rear (41-P-2903).
cylinder cam gears by pulling them out of crankcase bushings. Large (8) REMOVE VALVE TAPPETS AND VALVE TAPPET GUIDES (fig. 31 ).
intermediate gear is retained on stud by means of spring lock ring. Tappet guides are long-life members that seldom require replacement.
When removing timing gears take care not to lose any shims that may 47
46
The two cap screws enter through the left case and thread into the
LEFT SIDE CRANKCASE right case.
(a) Remove the two cap screws from lc:ft side case. Remove nut
from one end of each of the five studs.
(b) Studs serve as case registers. The long stud at top of the
crankcase (between cylinder bases) and two studs at the bottom of
the crankcase are a tight fit to serve as reg\sters. It will be necessary
to drift these studs out of crankcase. using a drift somewhat smaller
FLYWHEEL in diameter than the studs.
ASSEMBLY (c) Separating Cases. With all studs and cap screws removed.
crankcases can be separated by tapping lightly at mounting lugs,
using a block of wood and a hammer. CAUTION: When separating
cases, exercise care to keep flywheel shaft roller and retainer sets
intact.
' -
I
'
CRANKCASE
BOLTS AND NUTS
RA PO 310314
Figure 32-Separating Crankcases

H~we~er •.if it has been determined that tappet clearance in the old
gutde IS m excess of 0.002 inch, then remove guides and tappet as
follows:
(a) Tappet guides are a light press fit in crankcase and are re-
tained b~ screws. Remove screws. NOTE: Cam gear must be as-
sembled rn case for the tappet to rest against when using puller
(41-P-2956).
(b) Heat crankcase around tappet guide and pull guide with
special puller (41-P-2956).
(9) DISASSEMBLE CRANKCASES (fig. 32). Crankcases are held
together with two cap screws, and five studs with a nut on each end.
49
48
CHAPTER 3
CHAPTER 3
ENGINE. (Cont'd)
ENGINE (Cont'd)
Section Ill
Section II
DISASSEMBLY, CLEANING AND INSPECTION, FITTING
DISASSEMBLY, CLEANING, INSPECTION AND REPAIR CRANK PIN AND MAINSHAFT ROLLER BEARINGS, AND
AND ASSEMBLY OF CYLINDERS AND PISTONS, ASSEMBLING FLYWHEEL ASSEMBLY
AND CONNECTING ROD ALINEMENT
22. DISASSEMBLY.
21. CYLINDEHS, PJSTO~S AND t:ONNECTING R OOS. a . R e m ove Rig ht Flywheel fro m Crank Pin. Secure flywheel
~· D isassembly, cltani ng. insp ecti_on , repair , a nd assem bly of sprocket side mainshaft in vise with copp er jaws wh en disassembling
cylmder Pist ons an~ co~ncctmg rod a lmemcnt a re covered in chapter flywheels.
.2. overhaul of tngtne tn v<·hiclc. F o llowing are the pRragraph ref- ( 1) Remove retaining screw an d lock wash er from crank pin
er<.nces for th c·se subassemblies. right end ( gear sh aft side) nu t .
( 1) Cylinder d isassembly, refer to p a ra gra ph 7. (2) Remove crank pin nut.
(2 ) Clean ing o f cylinders and related pa rts: r efer to paragraph 8.
PINION GEA R SHAFT
(3) R ep air of cy lind ers and valves. refer to paragraph 9.
(4) Assem b ly of cylinders, refer to paragra ph 10.
SOFT HAMMER
( 5) Info rmation on piston s, piston pins a nd rings, refer to para-
graph 11.
(6) Informa tion o n alining connecting rods, refer to paragraph 14.
, 1
BETWEEN -
CRANK PIN Y WHEELS ,....,
LOCK SCREW
I. LOCK NUT
~~ lA PD 310115
Figure 33-Separating Flywheels
(3) Separate flywheels by striking rim of right side flywheel with

a soft hammer about 90 deg rees away from crank pin (fig. 33). O n e
or two sharp blows will usually loosen w heel. C A UTI O N : Do not
strike wheel on its side, as doing so might either break fly wheel or
damage the tapered crank pin hole.
b. R emove Connecting R ods and Rolin Bearing Assem bly fr~m
C rank P in . Using a piece of pipe (or the lower half of a v alve sp nng
50
51
DISASSEMBLY, CLEANING AND INSPECTION, FITTING CRA~K PIN
AND MAINSHAFT ROLLER BEARINGS, AND ASSEMBLING
FLYWHEEL ASSEMBLY
with air. Exercise care not to lose or mix up the crank pin roller
-
bearings.
I i b . Inspect ion. Inspection of roller bearings and shafts requires
use of a precision micrometer t o d etermine extent of wear. Outer races
must be closely inspected and gaged with size plug or shaft and over-
• size rollers to determine amount of wear .
(1) INSPECT SHAFTS AND RACES. Carefully examine all shafts
and bearing races for damaged and pitted surfaces. If any parts are
. - found with rough or pitted surfaces, replace them. Measure shafts
ROLLER ASSEMBLY
I I with micrometer for wear. Replace shafts that show any trace of a
RIGHT FLYWHEEL
ASSEMBLY
SOFT HAMMER
ROD THROUGH
HOLE IN FLYWHEEL
PREVENTS TURNING
L~~e~
SCREW LOCK NUT lA PO 310316
figure 34-Remo ving Conne cting Rods with Crank Pin Roller Bearing
. I
cover) about 1 ~~ 6 inch inside diameter and two. or thre~ inches lo~g,
hold roller bearing assembly in place on crank pm and lift connectmg
rods off of bearings (fig. 34). Lift roller and retainer assemblies
from crank pin, wrap in paper, and store in a box until i.:tSpection is ,- l A PO 3 10333
made. I
f', R emove Crank Pin. Crank pin is keyed in left side flywheel. ' figure 35 - Removing Mainshaft Nut
Hold crank pin in vise with copper jaws, and after screw and lock
washer have been removed , remove crank pin nut. Remove assembly wear shoulder at sides of r oller path, or a re worn 0.0005 inch or more.
from vise and while holding flywheel strike end of crank pin squarely Bearing races that show any trace of a wear shoulder at sides of roller
and lightly with copper or lead hammer to drift it out of flywheel. path must be lapped true or replaced if worn more than 0.0005 inch.
d. Remove Mainshafts. Remove mainshaft locks and nuts. Secu~e Refer to paragraph 25 for directions for lapping a nd sizing main
mainshaft in vise with copper jaws and after screw and nut lock IS bearings. NOTE: Connecting rod lower bearing races when worn in
removed, remove nut from mainshaft (fig. 35). Holding each flywheel, excess of 0.0005 inch or when pitted, must be replaced with .new rod
drift shaft from wheel, using copper or lead hammer. assemblies. Refer to paragraph 12 a for inspection and repair of piston
pin bushing.
23. CLEANING AND INSPECTION. (2) INSPECT ROLLER RETAINERS. Inspect all roller retainers for
a. Cleaning. Before attempting to inspect and size bearings, shafts cracks and extent of wear ; comparing them with a new retainer is
and races, clean all parts thoroughly in dry-cleaning solvent and dry best method.
52 53
DISASSEMBLY, CLEANING AND INSPECTION, FITTING CRANK PIN
(3) INSPECT FLYWHEELS. After flywheels are thoroughly cleaned, fLYWHEEL ASSEMBLY
inspect for breaks or cracks, especially at taper holes. A wheel with
crack at taper hole cannot be made to stay in alinement after as-
determining roller bearing fit. Bl·aring must not be so tight that the
shaft has no shake at all. Sprocket shaft main bearing clearance is
sembly.
0.0005 to 0.00 I inch.
(a) Inspect Flywheel Connecting Rod Thrust Washers. If washer
in either wheel is worn and/ or grooved to any extent, it must be (a) After sprocket shaft main bearing fitting is completed, left
side of crankcase with roller and retainer assembly can be set aside
replaced.
until flywheels are assembled.
24. FLYWHEEL REPAIR. (2) GEAR SHAn MAIN BEARING. One set or 12 rollers (0.550 in.
long) with two retainers is used in this bearing. With gear shaft for
a. The only repair that can be made to flywheels is the replace- size plug. select largest roller size that will allow the shaft just a little
ment of the connecting rod thrust washers which fit into recesses in more noticeable shake in the bearing than that allowed for the
flywheel faces, around the crank pin holes. These thrust washers are
hardened steel and cannot be drilled.
SPROCKET SHAFT
(1) REMOVAL OF THRUST WASHERS. Drill a Ys-inch hole in
flywheel at outer edge of washer to permit inserting a pointed tool
underneath the washer, in order to pry it out. Drill the hole only
slightly deeper that the thickness of the washers. CAUTION: A hole
drilled too deep may cause flywheel to crack.
b. Installing Connecting Rod Thrust Washers in Flywheels.
Before installing a new thrust washer, scrape the outer edge of the
recess where flywheel metal was punched against old thrust washer.
Thoroughly clean recess, as new thrust washer must seat fully on
recess bottom. If thrust washer is incorrectly installed and does not
seat fully in recess, the female (forked) connecting rod may not have
the required side play when flywheels are assembled. Retain thrust
washers in flywheels by several punch marks at outer edge of washers.
25. FI'ITING CRANK PIN AND MAINSHAFT ROLLER

BEARINGS.
a . Roller BParings Available in Oversizes. Usually the roller
races in crankcase and connecting rods can be smoothed up and sized RETA INER
by use of the lapping arbor so that oversize rollers can be fitted.
Standard roller size is Y4 inch. Rollers or roller and retainer sets are LEFT CRANKCASE RA PO 310361
available in steps of O.OOOfl, 0.0004, 0.0006, 0.0008 and 0.001-inch over-
size. In cases where roller races have worn to such extent that the Figure 36-Using Gear Shalt as Size Plug to Determine Bearing Fit
largest oversize rollers do not give the required clearance, then the
races must be replaced. sprocket shaft bearing (fig. 36). G ear shaft main bearing clearance is
b . Fitting Mainshaft Bearings (fig. 36). When fitting mainshaft 0.0008 to 0.0012 inch.
bearings, the shafts to be used when flywheels ~re reassembled can c. Assemble St>rocket Side and Gt>ar Sitle Mainshafts to Fly·
be used as gages to determine when roller bearings are fitted to cor- wheels. It is necessary to assemble mainshafts to their respective fly-
rect clearance. After crankcase mainshaft bearing races have been wheels at this time in order to proceed with connecting rod and crank
trued by lapping (par. 29 a (3)) roller bearings can be fitted as pin bearing fitting. Shaft tapers ahd flywheel tapers must be perfectly
follows: clean and free of oil, and keys must be in place when installing main-
(1) SPROCKET SHAFT MAIN BEARINGS. Two sets of 12 rollers shafts in flywheels. NOTE : Nut Jock washers can be installed either
(0.360 in. long) and retainers are used in this bearing. Using the side up and either lock screw hole may be used. If lock screw cannot
sprocket shaft as a size plug, select the largest roller size that will be inserted with lock washer in any of its various positions, turn shaft
allow the shaft just noticeable shake in the bearing. NOTE : Roller nut tighter, rather than looser, to bring lock washer to position where
bearings, shafts, and races must be perfectly clean and dry when screw holes line up.
54 55
DISASSEMBLY, CLEANING AND INSPECTION , FITTING CRANK PIN
(1) Left side (sprocket side) flywheel is quickly identified by AND MAINSHAFT ROLLER BEARINGS, AND ASSEMBLING
timing mark on outside rim face and keyway for crank pin. Install FLYWHEEL ASSEMBLY
sprocket shaft and tighten nut very tight, striking wrench with a (2) Temporarily install right side flywheel and shaft assembly on
hammer (fig. 35). Install nut lock and tighten retaining :;crew. crank pin and check oil passage through pinion gear shaft, flywheel
(2) Right side (gear shaft) flywheel is quickly identified by oil side and crank pin with compressed air. Make sure this passage
.
IS open.
feed hole drilled to connect crank pin and gear shaft holes. Install
gear shaft, nut and lock as in ( 1) above. After gear shaft is installed, .-. Fitlin~ Cran k Pin a n d Connt>c- t in~ Rod Bf'arin gs. New rods or
' - used rods returned for rebushing are usually fitted with crank pin
'
FRONT I and rollers. In this case, the rods and bearing assembly can be as-
sembled to flywheels without further attention, other than thorough
INOIER CONNECTING ROD
cleaning to remove antirust preparation. New rods, or rebushed rods,
--
also are fitted with new piston pin bushings reamed to standard size.
•
'
•'
Hold left side flywheel and gear shaft assembly in vise copper jaws so
that crank pin is in vertical position .
• (1) LAPPING WORN CONNECTING Roo ROLLER BEARING RACES
-
• (fig. 37). When lapping a set of worn rods, lap until no trace of wear
I shoulder is left at sides of roller path; also lap both rods (front and
•
l rear) to fit same size rollers. When rod roller races are damaged or
worn beyond truing up and refitting with largest oversize rollers. rods
i' must be replaced with new rods or rods rebushed and reconditioned.
(a) New rods, not already fitted with rollers and crank pin, are
likely to need lapping to fit avail.:~ble rollers and give specified
clearance.
(2) Use special arbor (41 -A-337-10). Use lathe or speed head to
• chuck and turn lap 1SO to 200 revolutions per minute. Adjust lap
.. with wrench ( 41-W -47 5) to fit -snug in rod race before applying lap-
ping compound: a loose lap will bell mouth the bearing race. Apply
a light coat of fine lapping compound to lap. To avoid grooving or
tapering of lap, work the rod back and forth along full length of
lap.
(3) ROLLER BEARING FITTING. Rollers must always be new and
assembly must not be made up of mixed sizes. Roller sets and roller
and retainer sets are available in standard (0.250 in.) and 0.0002,
0.0004. 0.0006. 0.0008 and 0.001 inch oversizes. Rollers used in the
lA f'D 210300
female (forked end) rod are 0.270 inch long. Rollers used in the
AREiOR IN LATHE CHUCK
male (single end) rod are 0 .550 inch long. If old retainers are used,
Figure 37 - Lapping Connecting Rod Roller Race with inspect them for good condition by comparing with new retainers.
Lapping Arbor (41- A - 337- 10) NOT E: Over-a/I width of roller retainer assembly must be less than
width of female (forked end) rod; check to make sure of this.
check oil passage through shaft and side of flywheel (to crank pin (a) With flywheel sprocket shaft gripped in vise copper jaws so
hole) with compressed air, to be sure oil passage is open. that crank pin is in vertical position, install a set of rollers and
retainers in crank pin. Check fit of each rod on bearing assembly. If
d . Insta ll Cr ank P in in Left Side F lywh eel. I n order to correctly neither rod will start over the roller assembly, select a smaller size
fit crank pin and connecting rod roller bearing, crank pin must be set of rollers. CAUTION:.,. Do not mix up bearings. Keep each size
installed in left flywheel and mainshaft held in vise copper jaws. in its respective contamer. If rods go over bearings easily .and there
( 1) Crank pin taper and flywheel hole must be perfectly clean is considerable shake at top e~d of rods, install a larger oversize set
and free to oil and key must be in place when crank pin is installed. of rollers. If lower end of one rod is found to be slighU¥ larger than
the other, it is best to select a roller size that comes closest to correctly
Turn on crank pin nut, striking wrench with a hammer to securely fitting the larger rod race and then lap the smaller rod race to bring it
tighten nut. Install nut lock and securely tighten retaining :>crew. up to the same size, rather than fit bearing with rollers of two sizes.
56 57
DISASSEMBLY, CLEANING AND INSPECTION, FiniNG CRANK PIN
(b) When rods are correctly fitted with required bearing clear FLYWHEEL ASSEMBLY
ance, extreme upper end of female (forked) rear cylinder rod will 90 degrees from crank pin. Tighten crank pi~ n_ut lightly. Check rim
have just noticeable side shake. Upper end of male (single end) faces again with straightedge (fig. 39) and tf t1~htenmg of nut~ has
front cylinder rod will have '!:{:! to %4 -inch side shake. This ch eck shifted wheel. correct its position by striking nm of wheel ~1th a
should be made with bearings clean and free of oil. F itting this soft hammer. Do not use a hard steel hammer. Turn crank pm nut
important bear ing tighter is likely to result in a "seized" and damaged tighter tlnd repeat straightedge ch('ck. T_o pre~ent fty~heel assembly
bearing shortly a fter engine is back in service. from turning in vise copper jaws while taghtenmg nut, msert a rod or
(c) After correct connecting rod and crank pin bearing fit has bolt (Y2 inch x 5 or 6 inches long) through holes m flywheels ~nd
been attained, t h oroughly clean all parts and lubricate with engine oil shift wheels in vise so that rod or bolt bears agamst some part of v1se.
preparatory to assembling flywheels.
(' , Ch ..t·k ing Ho •l S it.le Pia} Bf' tWt't-n F lywh t'ds. It is important
RIGHT SlOE FLYWtiEEL ASSEMBLY PIN GEAR SHAFT
that side play of female (forked) rod be between 0.006 and 0.010
~--
OIL HOLE IN
CRANKPIN
-
FRONT CYLINDER I
COI-4NE4:TI~~G ROO I
I
-
I
--41 I I
REAR CYLINDER ~
CONNECTING ROO I
LEFT SIDE '
FLYWHEEL ASSEMBLY I
LOC~
SCREW LOCK NUT -
.. <::>
ItA PO 310377
Figure 38-Assem&ling Flywheels It A PO 310321
Figure 39-ChecJcing Flywheel Rim Faces

26. ASSEMBLING FLYWHEELS.
a . The flywheel assembly is a built-up crankshaft and must be as inch when wheels are finally trued and crank pin nut finally and
true as possible (as .if in one piece) after alinement. When assembling securely tightened. A minimum rod side play check before wheel
flywheels, make sure that connecting rods are installed on crank pin truing is advisable to prevent further possible trouble and extra work.
bearing so that female (forked end) rod will fit into rear cylinder, and ( 1) Roo MINI MUM SIDE PLAY CHECK. Before at tempting to true
male (single end) rod will fit into front cylinder (fig. 38). T his rod flywheels, check side play between female (forked) rod and flywheel
arrangement provides better crank pin bearing lubrication. D o not t h rust washers for minimum side play (clearance) , P ush the rod
assemble flywheels until crankcase main bearings have been repaired tight against one flywheel thrust washer and check clearance betw:en
(par. 25). rod and the other wheel with thickness gage (fig. 40). If rod s1de
b . Install Right Sidt> Flywh eel. With left side flywheel and rod play is less than 0.007 inch. correction must be ~ade before con-
assembly held in vise copper jaws, wipe all traces of oil from crank tinuing with assembly and truing operations. If the s1de play between
pin taper and fight flywheel taper hole and install wheel on cran k forked rod and flywheels is less than 0.007 inch, it may be due to ~ne
pin. Aline wheel as nearly as possible concentric with left side wh eel of the following conditions: F lywheels and crank pins assembled w1th
by means of a straightedge held against outer face of wheel r ims oil on tapers and crank pin nuts overtightened; new flywheel thrust
58 59
DISASSEMBLY, CLEANING AND INSPECTION, FITTING CRANK PIN
FLYWHEEL ASSEMBLY
washers installed and not fully seated; tapered holes in nywhr( IIi truing is the reason why final side play recheck is necessary after
mlarged as a result of flywheels having been taken apart ond rr truing flywheels and tighteni,lg crank pin nut.
assembled severa l times; flywheel cracked at tapered hole. d. :\take Final Gear Sh aft, Flywht>t>l, a nd Crank Pin Oil Pas-
(2) CORRECTING R oo SIDE PLAY (BETWEEN FLYWHEELS) W111 N sage Test. After flywheels and rods are assembled. make final check
L ESS THAN 0.007-JNCH. I n a case of this kind. the first thing to d" t o be sure oil passage is open to rod bearing. Apply compressed air
is to disassemble flywheels and recheck flywheel thrust washt:rs H to hole in side of gear shaft. near its outer end, and observe that air
these washers are found fully seated and secure in flywheels, tht 111 xt escapes around connecting rod lower end. If this passage becomes
best thing to do is determine which flywheel seats farthest on thr blocked in some manner and engine is assembled and put in service
crank pin taper, due to enlarged tapered hole or a crack, and replnl e
that flywheel with a new one. INDICATOR FLYWHEa ASSEMBLY INDICATOR
ADJUSTABLE CENTER
CENTER LOCK
FRONT CYLINDER THICKNESS GAGE

CONNECTING ROD
FORKED
REAR CYLINDER
CONNECTING ROD
COPPER HAMMER
"
' • •
.. '
figure 4J-Truing Flywheels to Aline Mainshalts in
Stand (41-S-4970)
RA PD 310332
figure 40-Chedcing Connecting R.od Clearances with it blocked, engine will get no lubrication except in timing gear
case. This is not likely to be detected until serious damage has been
done, as the oil circulation indicator in instrument pan el will give
(3) CoRRECTING Roo StoE PLAY (BETWEEN FLYWHEELS) WHEN
no warning when the oiling system is blocked in this passage.
IN EXCESS OF 0.0 10- JNCH. After flywheels are trued and crank pin
nut finally and securely tightened, the end play of the female (forked)
rod between flywheel thrust washers should not exceed 0.010 inch. If 27. TRUING FLYWIIEELS.
thickness gage check reveals excessive side play, probably all or most a. Bear in mind that, while a straightedge across rim faces is
of the excess play can be taken up by tightening crank pin nuts a used when assembling flywheels to keep them as near as possible true
little tighter. with each other, final truing is a matter of truing sprocket shaft and
(4) RECHECK Roo SIDE PLAY BETWEEN FLYWHEELS AFTER F LY· pinion shaft to perfect alinement with each other, rather than truing
WHEELS ARE TRUED. The crank pin nut is not drawn up to final tight- 61
ness before truing flywheels, and drifting of wheels on crank pin while
60
CHAPTER 3
ENGINE (Cont'd)
flywheel rims. Install wheel assembly in tqling stand (41-S-4970) and
adjust so that centers are just snug (wheels must turn freely). If Section IV
flywheel assembly is either loose between centers or is squeezed, indi-
cators will not indicate accurately. Indicators should be adjusted CLEANING, INSPECTION, AND REPAIR OF CRANKCASE
as closely as possible to flywheels, and so that pointers rest about in ASSEMBLIES AND GEAR CASE COVER
the middle of graduated scales (fig. 41).
(1) TURN FLYWHEELS AND OBSERVE THE MOVEM~NT OF INDI- 28. CLEA~IN("; AND I~SPECTJOt\ ( tF CRANKCASE.
CATOR PoiNTERS. Movement of pointers toward flywheels indicates a. Clf'anin~. After flywheel assembly has been removed from
high points of shafts. Find highest point of each shaft and mark fly- crankcase, clean cases thoroughly in dry-cleaning solvent. CAUTION:
wheel rims at those points. Loosen device centers slightly, just enough Do not use cleaning solution or method that will injure aluminum
so it can be detected that flywheel assembly is a trifle loose. Turn cases. R emove all traces of shellac from face of each case center
high point of first one flywheel and then the other to the top and joint for perfect oil seal upon reassembly.
strike rim of wheel one or more sharp blows with a soft hammer.
The number of blows required, and how hard they should be struck,
depends of course, on how far shafts are out of true. Remember that
device centers should be loosened slightly before striking fty~heels.
However, they should not be loosened to the extent of allowing fly- FRONT EXHAUST
REAR EXHAUST CAM GEAR BUSHING
wheels considerable play between centers, as making them very loose CAM GEAR BUSHING
is likely to result in broken or damaged centers.
(2) READJUST TRUING DEVICE CENTERS. After striking wheels
with hammer as explained in a (1) above, readjust device centers to
just snug and again turn wheels and check with indicators. Repeat
the truing operation until indicators show within 0.001 inch of true.
Each graduation on indicator scale is approximately 0.002 inch,
therefore, when shafts are true within requirements neither indicator
will move more than about one-half graduation.
(3) FLYWHEEL ASSEMBLY THAT CANNOT BE TRUED. In the case
of a flywheel assembly that is considerably out of true and which
cannot be trued up by following the procedure described, it may
be due to crack at one of the flywheel shaft holes or a damaged and
enlarged taper hole. If used sprocket and pinion shafts are assembled
in flywheels, it may be due to one of these shafts being worn con-
siderably out of round at the point where indicator takes bearing
against it.
(4) MAKE FINAL CONNECTING Roo SIDE PLAY (BETWEEN FLY- lA PO 210326
WHEELS) INSPECTION. See paragraph 26 C (1), (2), (3) and (4) for
Figure 42-Cam Gear Bushings in Right Crankcase
instructions on connecting rod side play between flywheels after crank
pin nut has been securely tightened by striking wrench with a
hammer. NOTE: After rod side play has been checked and adjusted, b. lnSJH"t'lion. Inspect cases for good condition, examining closely
crank pin nut pulled very tiAht and nut lock washer fitted, aAain for cracks, holes, and/ or broken parts. Crankcases are supplied in
matched sets to ensure perfect cylinder base and bearing alinement.
install wheel assembly in truinA device and recheck for trueness.
If one side of case is damaged beyond welding or local repair, it
must be replaced with a matched pair.
(1) I NSPECT TIMING GEAR SHAFT BUSHINGS. When bushings are
worn to the extent that gear shafts have 0.002 inch or more clearance.
such bushings must be replaced.
(2) INSPECT MAIN BEARING RACES. Wear shoulder must be
removed from roller races before accurst s1zmg inspection can be
made. Refer to paragraph 23 b (1). Usually, the race can be trued
63
62
- ----
CLEANING , INSPECTION, AND REPAIR OF CRANKCASE

?Y lapping to remove any wear shoulder and oversize rollers can be ASSEMBLIES AND GEAR CASE COVER
mstal.led. When race is worn to such extent that use of 0.001 inch (c) Bushings must be line-reamed, after gear case cover has been
overs1ze rollers will give more than specified clearance, replace the repaired and it is in place . .vith special reamer (41-R-2265. fig. 46).
race (par. 29 a (2)).
Gear shaft clearance in cover bushing is 0.0005 to 0.001 inch.
29. REPAIR OF CRANKCASE. (2) REPLACING MAIN BEARING RACES. When renewing main
bearing races, heat cases (not above 3oocF) around races. Heating
a •. In case~ whc:re welding can effect a satisfactory repair without expands cases slightly and less force is required to press old races out
~arpmg or dtstort10g case or necessitating use of special tools and and new races in. New races, after installation, must be lapped to
Jigs for accurate machining after repair is made, it is recommended smooth, true and aline them, and to size them so that specified bear-
procedu~:e. G eneral practice is to r eplace broken or damaged case. I
ing clearance can be attained with smallest roller sizes available.
-
CRANKCASE ASSEMBLY
•
_ CRANKCASE MAIN BEARING . .. (3) TRUING AND SIZING MAIN B EARING RACES IN CRANKCASE I
ADJUSTABLE LAPPING TOOL (fig. 43). Assemble crankcase (without flywheel assembly) and lap
' ...
· ., _ (41-L-203) bearing outer races to true them and remove any trace of I
•
\ . • • wear shoulder at sides of roller path. I
,_ •
•
FRONT EXHAUST
CAM GEAR BUSHING
OIL HOLES REAR INLET I
CAM GEAR BUSHING
REAR EXHAUST
I
•
CAM GEAR
BUSHING
I
I
•
•
I
•
l
/ I
•' l
•
• l
'
•
' INLET PINION SHAFT
·-
BUSHING
•.• ' CAM GEAR BUSHING
.... ,0 310327
Figure 43-Lapping and Truing Crankcase Main Bearing Races Figure 44-Cam Gear Bushings in Gear Case Cover
with Lap (41-L-203)
(a) Lap first one case side race and then the other, guiding lap
. (~) REPLACING TIMING GEAR BUSHINGS IN CRANKCASE. The four by means of pilot bushing in opposite case side race. Adjust lap
tlm10g gear bushings in crankcase can be replaced with an arbor snugly in race and use only a light application of fine lapping com-
press (fig. 42?. Press bushings out from inside of case. Remove the pound. CAUTION : A loose lap and the use of excessive amount of
steel dowel p10s with pliers. compound results in a tapered bearinA surface.
(a~ When ~ew bushings are pressed into place, make sure that
the od grooves 10 shoulder face are in upward position.
(b) Sprocket Shalt Bearing Race. Lap sprocket shaft bearing
outer race to obtain a clearance of 0.0005 to 0.001 inch, using the
I
(b) ~fter bushings are pressed into crankcase they must be desired set of rollers and using the sprocket shaft that will be installed I
dowel_ p10ned ~to _prevent bushings from turning) , by drilling a No. in the flywheel assembly.
31 dnll hole, ~32 10ch deep, through bushing flange and into alumi- (c) Gear Shaft Bearint Race. Lap gear shaft bearing outer race
?um. case_. The hole should be of correct depth so when dowel pin to obtain ~t clearance of 0 .0008 to 0.0012 inch, using the desired set of
~s dnven 10 and bottomed, its end will be slightly below face of bush- rollers and using the gear shaft that will be installed in the flywheel
10g flange. Peen bushing around dowel pin hole to retain it.
assembly.
64 65
CLEANING, INSPECTION, AND REPAIR OF CRANKCASE
ASSEMBLIES AND GEAR CASE COVER
30. CLEANING AND INSPECTION OF GEAR CASE COVER.
a. Clean. Clean gear case cover in d r y-cleaning solvent, exercis- PULLER TAP ' PULLER TAP ·
ing care not to scratch or mar face finish. SCREWED INTO IN BUSHING
b. Inspect Timing Gear Sh aft Bushings (fig. 44). When bushings BUSHING
'
in gear case cover are worn to such extent that shaft clearance is •
0.002 inch or more, cam gears are likely to become very noisy. Re-
place bushings if this is found.
31. REPAffi OF GEAR CASE COVER

a. It is not advisable to make a weld repair to gear case cover.
A broken or badly damaged cover should be replaced. Before remov-
ing old bushings, note location of oil transfer hole (rectangular shape)
,,... '
in pinion shaft bushing. Gear case cover bushings can be removed as J
follows: ~' ;, PULLER SLEEVE
{1) REMOVE BUSHINGS. Use special puller {41-R-2372-20, fig. 45) A- THREADING TAP INTO
BUSHING
to pull blind bushings from gear case cover. Puller body provides
four special puller-tap sizes to accommodate bushings. T he open
bushing (rear cylinder exhaust cam gear oil pump drive) can be
removed with an arbor press.
>. PULLER TAP IN
b. Install Gear Case Cover Bushin gs. Installation of the five PULLER NUT . ' POSITION
bushings in the gear case cover requires special attention in each
case. Installation of each bushing is covered in the following instruc-
tions:
(1) FRONT CYLINDER EXHAUST CAM GEAR BuSHING. Press bush -
ing into gear case cover and drill a No. 31 hole, %2 inch deep, through
flange into aluminum so that dowel pin end is just below face of
bushing flange. Peen bushing around dowel pin hole to retain pin.
Drill oil hole (use %2 in. drill) through bushing, using hole in bushing
boss as a guide. •'
(2) FRONT CvLtNDER I NLET CAM GEAR BusHING. Press bushing TURN ON PULLER NUT WITH
HANDLETO PULL BUSHING HAN
into gear case cover with narrow end of flange downward so that ....__....., OUT OF CASE COVEF~I,.;:iW REMOVED
"" RA PD J10147
clearance is provided for cam gear teeth. Drill No. 31 hole through C-TURN UNIT CLOCKWISE D--USE STEPPED SLEEVE
flange for dowel pin, and drill a %2 -inch oil hole in bushing as out- TO PULL BUSHING TO CLEAR BUSHING BOSS
lined in b ( 1) of this paragraph.
(3) REAR CYLINDER INLET CAM GEAR BUSHING. Follow instruc- figure 45-Removing Blind Bushings in Gear Case Cover wirh
tions outlined under b {l) of this paragraph. Puller (41-R- 2372-20)
(4) REAR CYLINDER EXHAUST CAM GEAR-OIL PUMP DRIVE
SHAFT BuSHING. This large flange bushing must be pressed into case pin in until end is slightly below sur face of bushing, being careful not
cover until face of bushing is flush with machined surface of case to drive bushing deeper into cover, and· lower flange below cover sur-
to provide correct seating and clearance for oil pump. Use a smooth face. Do not peen this pin hole.
surfaced disk or plate a little larger than the bushing flange diameter (5) PINION GEAR SHAFT BusHING. Install this bushing with oil
when pressing bushing into case cover to ensure flush fit. If available transfer hole (rectangular shape) upward and 30 degrees ahead
bushing flange is Y8 inch thick, put on lathe mandrel and remove lfa 2 (toward front of engine) of vertical center line. Normal functioning
inch from outside face and 0.015 inch from inside face to make flange of engine oiling system depends upon correct location of t his hole.
0.078-inch thick. Later bushings will be made to these specifications. Drill a No. 31 drill size hole, %:?-inch deep, t hrough flange into
Drill a No. 31 drill size hole, %2 -inch deep, in the bushing flange to aluminum and drive dowel pin in. The e ••d to be just below face of
right of original pin hole, to accommodate dowel pin. Drive dowel bush ing flange. Peen m etal arou nd hole to retain pin.
66 67
CASE BUSHING TIMER BUSHING

REAMER n REAMER
tfMII.'I PA$!1.S
PIN - u lWlOUGH GU10E TO
REAM PINION SIVJ'T PtlOl GUIDE
IN RIGHT CIANKCASf
Figure 47 -Pilot Guide Located in IUSHING IN GEAR CAS!
COVER aEAIIING OUTBI lACE
Bearing Race to line-ream Pinion
Shaft Bushing in Gear Case Cover
with Reamer (4f-R-2304)
PIN RETAINER
A-«EAMER PASSED THROUGH CRANK CASE BUSHING IN

POSITION FOR TIMU BUSHING REAMER ASSEMBLY
i
-
REAMER
ASSEMBLED REAJI EXHAUST CAN. Figure 48-Line-reaming Oil Pump
II.ISHING IN
~
LARGE SIZE GEAR CASE COVER Drive Shaft Bushing and Crankcase
.
I
FOit COVEtt
BUSHING
Rear Exhaust Cam Bushing with
'
Reamer (4f-R-2303)
SMAll SIZE
FOR CRANKCASE
BUSHING
TIMER BUSHING
IN CASE COVER
1-REAM£11. ASSEMBLED TO REAM CASE COVEl TIMER BUSHING

AFTtR CASE COVER IS IHSTALLED OH CRANK CASE
c. Line·rf'am Bushings. Assemble gear case cover to crankcase
to correctly line-ream all timing gear and gear shaft end bushings.
RA PD :110311 NOTE: Reamer (41-R-2265) for cam ~ear shalt and timer d rive
Figure 46-Preparing to Line-ream Cl'anlccase and Gear Case Cover shaft bushins is of two-piece construction and large reamer end must
Bushings with Combination Reamer (4f-R- 2265) be installed before case cover is assembled to crankcase as follows:
•
68 69
.• -
u
• ••
CLEANING, INSPECTION, AND REPAIR Of CRANKCASE
(1) REAMING REAR C YLINDER INLET CAM GEAR SHAFT AND 32. INSPECTION AND REPAIR OF VALVE TAPPETS AND
TIMER DRIVE SHAFT B usHINGS. P ass reamer (41- R -2265) through VALVE TAPPET GUIDES.
crankcase bushing from inside. D o not tum reamer in bushing. Slip a. Inspection of Valve Tappets. Inspect valve tappets for exces-
large hollow reamer over en d of smaller reamer and engage pin (fig. sive clearance in guides. Also inspect tappet rollers for excess1ve
46). J ust start large reamer in timer drive shaft (l~ in.) bushing a nd bearing looseness a nd damaged roller faces. Tappets have 0.0005. to
install gear case cover on crankcase, registering dowels and securing 0.001-inch normal clearance in guides, and it is recommended practtce
cover with at least four screws. to install n ew tappet and roller and 1or guide assembly when clear-
(a) Line-ream Bushings. Aline and size bushings by turning ance exceeds 0.0025 inch.
combination reamer into crankcase and case cover as far as it will (1) REPLACEMENT OF TAPPET R?LL.ER. When t~J?pet. r<~ller only
is excessively loose on pin, or otherw1se m bad cond1tion, 1t 1s reco~
go.
mended that entire tappet assembly be replaced. In case roller only IS
(2) L INE-REAM PINION SHAFT B usHINGS. L ine-ream (reamer replaced, roller must turn freely on pin and have 0.008-inch side play
41-R-2304) with crankcase a nd gear case cover assembled . Insert after new roller pin is securely riveted i.n tappet.
guide bushing into crankcase roller race and turn r eamer until it
b. Inspection and Replarf'ment of Valve Tappet Adjusting
bottoms in gear case cover (fig. 47). Screw. When end of valve tappet adjusting screw is worn hollow from
action of valve stem, it should be replaced to ensure accurate valve
tappet-valve stem adjustment.
c. Installing V alv(' Tappt'l Guides. When installing valve. tappet
guides (with tappet assemblies) in crankcase, note tha~ _gu1de f~r
front cylinder can be used in either intake or exhaust pos1t~on but IS
not interchangeable with rear cylinder valve tappet gu1de. Rear
cylinder tappet guides are interchangeable with each other, but not
with front cylinder tappet guides. Make sure paper gaskets are
between guides and crankcase.
( 1) VALVE TAPPET AND ROLLER ASSEMBLIES ARE INTERCHANGE-
ABLE.
33. INSPECfiO~ OF Tli\111\"G GEARS.

a. Timing gears, cams, and shafts must be considered as integral
units and must be replaced as such when necessary. Inspect for worn
shafts and gear teeth, damaged gear teeth and worn and / or pitted
cam lobe face.
(1) TIMING GEAR CAMSHAFT ENDS FOR CRANKCASE BUSHINGS.
Standard size is 0.687 5 inch .
figure 49-l.ine-reaming front Cylinder Inlet and Exhaust Cam (2) REAR CYLINDER EXHAUST CAM-OIL PUMP DRIVE SHAFT
Bushings in Crankcase and Gear Case Cover with Reamer (GEAR CASE CovER BEARING). Standard size is 0.7805 inch.
(41-R-2265) (3) REAR CYLINDER INLET CAM-TIMER DRIVE SHAFT (GEAR
CASE CovER BusHING). Standard size is 1.2425 inches.
(3) LINE-REAM REAR CYLINDER EXHAUST CAM GEAR SHAFT (4) FRONT CYLINDER I NTAKE AND EXHAUST CAMSHAFT ENDS
AND OIL PUMP DRIVE SHAFT BUSHINGS. Use reamer (41-R-2303) (GEAR CASE CovER BEARINO) . Same as step (1) above.
and with crankcase a nd gear case cover assembled, pass reamer
through bushings from gear case cover side (fig. 48). Turn reamer 34. DISASSEMBLY, CLEANING, INSPECTION, REPAIR AND
just sufficient to clean up and aline bushing holes. ASSE~BL Y OF OIL FEED PUMP.
(4) FRONT CYLINDER EXHAUST AND INLET CAMSHAFT BUSHINOS. a. Des(•ription. Main oil feed pump is of the vane-type. ~ rotat-
Line-ream with reamer (41-R-2265) using only smaller size of reamer ing member, driven by rear cylinder exl.aust camshaft, retams and
combination (fig. 49). Pass reamer. through bushings from inside of drives two vanes within a slightly eccentl"ic housing. Pump incorpo-
crankcase and turn just sufficient to clean up and aline bushing holes. 71
70
CLEANING, INSPECTION , AND REPAIR OF CRANKCASE
rates an automati~ (centrifugal) by-pass valve, reducing oil feed (1) I NSPECT Pt7~tP BoDY. Inspect rotor chamber closely for
sup~ly at low engme . speed~ and i_ncreasing oil feed supply at high excessive wear caused by · •an~s. Pump body with badly worn rotor
engme ~peeds. Pump 1s prov1ded w1th ball spring adjustable pressure chamber should be replac ~d.
regulatm~ valve a_nd two ball-spring check valves. Maximum oil (2) INSPECT VANES AND SPR!NG. Inspect vane spring for break-
pressur~ IS ap~rox1mately 30 pounds. Rotation of rotor is counter- age and rusted condition. Spring has normal free length of 1 f}-{31!
clockwtse, lookmg at pump from back side. inches. Replace if found in bad order. Vanes will usually be found in
b. Disassembly. When disass~mbling oil feed pump, exercise good condition, unless excessively worn (rotor chamber would also
care not to lose parts, balls, and spnngs. Also note location of all parts be worn). R eplace worn or damaged vanes.
for correct reassem bly (fig. SO). (3) I NSPECT BALL-VALVE SEATS. Using a flashlight, inspect ball
seats in pump body for pits andi or dirty condition. NOTE: A small
particle of s tring, fiber. or other foreign matrer lodged on valve seat
will prevent ball frqm seating, thus preventing correct operation of
pump. B ody with damaged ball seats should be replaced.
(4) INSPECT BALLS AND SPRINGS. Inspect springs for breakage
OIL PUMP IIOOY and rusted condition. Replace if not in good condition. R egulating
CAP "x (by-pass) spring is %-inch in diameter and has normal free length of
21fi inches. Upper and lower check valve springs are interchange-
-~
6
able, being !'}~ 6 -inch in diameter with normal free length of 1 9/:~::! inch.
Steel balls may have rings formed by action on valve seats. Balls
V~
CHECK
SPRING
A.
/"'
not perfectly smooth and round should be replaced.
(S) INSPECT R OTOR ASSEMBLY. R otor and centrifugal by-pass
VALVE BAll valve assembly should show no appreciable wear.
d. Assembl.- Oil Ft>ed Pump. Pump body, ball valve seats. and
all passages must be thoroughly clean a nd free from dust, dirt, or
grit before assembly. Also, see that rotor, vanes. springs, balls, and
screws are clean before assembly. Refer to figure SO.
(1) INSTALL BALLS AND SPRINGS. Install the two check valve
balls and springs and secure with fillister head cap screws. Install
regulating valve (by-pass) ball and spring, turning down adjusting
ROTOR VANE-.~ rt:::.....t ~'"'RoTOR VANE . screw until head is %-inch below top of pump body. Replace oval-
head cap screw.
VANE SPRING • --=. (2) INSTALL R OTOR AND VANES. Install spring between rotor
lA I'D 310330 vanes and install rotor and vane assembly in pump body chamber.
Figure 50- 0il Feed Pump, Disassembled Make sure that chamber rotor and vanes are perfectly clean before
I
installation.
( 1) REMOVE R OTOR AND VANE ASSEMBLY. R emove rotor with
1
. ~
35. DISASSEMBLY, CLEANING, INSPECTION, REPAIR, AND

v_a nes and _spring, from pump body, holding vanes to prevent ~xpan ASSEMBI.Y Of SCAVE!\GER PUMP A~D CRANKCASE
S!On of spnng and possible loss of parts. UREATilER VALVE.
(2) REMOVE REGULATING BALL-SPRING VALVE. Remove valve a . The crankcase rotary breather valve is an integral part of the
co~er screw exposing adjusting screw. Remove adjusting screw,
scavenger (oil return) pump. The rotary valve (which drives gears
spnng, and steel ball. in scavenger pump) is driven by a spiral gear located on engine pinion
{3) RE~OVE CHECK AND REGULATING VALVES. Remove the shaft. Rotary breather valve must be accurately timed to control
screws, sprmgs, and balls of the check and regulating valves NOTE· the scavenging of oil from the engine crankcase. The scavenger pump
Both_ check valve sprin~s are the same and are interch~ngeable: also provides oil for rear chain lubrication. allowing a small amount of
Spec1al steel .balls used m the three ball-spring valves are of same oil to flow past an adjustable needle valve through a small pipe to
I
s1ze and are mterchangeable. t rear chain. It is possible to inspect and make repairs to scavenger
c •. Cleaning, Inspection and Repair. Clean all parts in dry- pump gears without removing pump body and breather valve from
cleamng solvent and blow out all pump body passages with air. 73
72
t~e engine _(e of this paragraph). Breather valve and scavenger pump ASSEMBLIES AND GEAR CASe COVER
gtve. very h~tle trouble and ordinarily a thorough cleaning is all the
servtce requtred. (1) INSTALL ROTARY BREATHER VALVE (fig. 51). Apply engine
oil to rotary breather valve and body chamber and assemble. Install
b .. Disassembly, _Cleaning, and Inspection. Thoroughly clear: key ( new one if necessary) in rotary valve end and slip pump drive
extenor of assembly m dry-cleaning solvent before disassembly. gear in place. Install split retaining ring. Coat gasket (use new
(I) REMOVE SCAVENGER PUMP COVER. Remove the two cap gasket if necessary) with engine oil and locate on pump body. Install
screws and separate cover from pump body, exercising care not to pump idler gear on cover stud and assemble cover and gear to pump
damage the paper gasket. With cover removed, pump gears are body. Install the two cover cap screws and lock washers. CAUTION:
exposed (fi_g. 51). T_h e drive gear is keyed on the rotary breather valve Do not ti~hten cap screws until complete assembly has been installed
a_nd the dnve gear tdles on the cover stud. Remove the split retaining in engine crankcase.
nng from end of rotary breather valve and drive gear is free for (2) INSTALL REAR CHAIN OILER ADJUSTING S CREW. Make sure
removal. that all of the thin adjusting washers removed from oiler adjusting
screws are back in place before installing the oiler adjusting screw.
Oil supply for the rear drive chain is adjusted on the vehicle (TM
UEATHER VALVE AND 9-879).
SCAVENGER PUMP IIOOY CHAIN OILER e. Scavenger Pump Fails to Return Oil to Tank. Should
?USTING SCREW scavenger pump fail to return oil to tank, as evidenced by excessive
PUMP smoking at exhaust and absence of oil at return pipe in tank, the
IIRE.f.THER VALVE
AND SCAVENGER IDlER GEAR ADJUSTING pump drive gear key is more than likely sheared. It is not necessary
PUMP GE.U DRIVE 0 SCREW to remove entire pump body from crankcase (throw breather valve
0 WASHERS
out of time) for inspection and repair.
0
0 (1) REMOVE SCAVENGER PUMP COVER. Remove the four pump
0 cover nuts and washers and the two cover retaining cap screws and
washers a nd remove cover, taking care not to pull pump body out
,-.. of crankcase.
(2) REPLACE PUMP DRIVE <;:fEAR KEY. Remove split ring which
cov~
SCAVENGER PUMP
DRIVE GEAR retains drive gear a nd withdraw gear from shaft. Remove broken key
from shaft and gear. Install new key, gear, split lock ring, and pump
AND WASHERS
cover. Check cover gaskets. Install the lock washers, nuts, and cap
RA 'D 310331 screws and securely tighten.
Figure 51-Scavenger Pump and Breather Valve, Disassembled
(2) REMOVE ROTARY BREATHER VALVE. After pump drive gear

has been removed, pull breather valve out of housing.
(3) ~M?VE R;EAR. CHAIN OILER ADJUSTING SCREW. Remove
r~ar cham otler adJUSting screw and thickness washers so that cover
otl channels may be cleaned out.
. ( 4) CLEAN ALL PA~TS. Clean all parts thoroughly in dry-clean-
mg solvent. Blow out ml holes and passages with air.
(5) INSPECTION OF ~A.RTS. Inspect rotary breather valve spiral
gear teeth for good condttlon. Inspect housing and cover for breaks
cracks, or other damage that requires replacement of these parts. '
c. Repair. Any damaged and/ or badly worn parts should be
rep~aced. _If rotary breather valve is damaged, it is advisable to replace
entire umt.
d. Assembly. All_parts m':lst be thoroughly clean before assembly.
Do n'?t .assemble umt to engme until crankcase has been assembled
and ptmon shaft gears installed, ready for timing.
74 75
FITTING AND ASSEMBLY OF FLYWHEEL AND
CRANKCASE ASSEMBLY
CHAPTER 3 37. 1\UNE ANO AllJUST l<'LYWIIF.EI. ASSEMBLY ll'i
CUAt\KCASE ASSE~ti~L\.
ENGINE (Cont'd)
a. Flywheel end play (side clearance) within crankcase is ad-
Section V justed by means of steel thrust coilars (washers) available in thick-
nesses of 0.066. 0.070, 0.074, 0.078, 0.082. 0.086, 0.090. 0.094• 0.098 and
FITTING AND ASSEMBLY OF FLYWHEEL AND 0.102 inch. These thrust collars come in sets of 10. containing one each
CRANKCASE ASSEMBLY of the above thicknesses. Thrust collars fit on flywheel hubs and are
registered on dowel pins to prevent them from turning. The average
36. CRANKCASE ASSEMBLY. thrust collar thickness used in assembly of a new engine is 0.080
inch. Flywheel end play gage (41 -G-198) is used to determine. with
a. The two halves of the crankcase completely enclose the fly-
aid of thickness gage. exact end play o f flywheels after crankcase
wheel assembly, providing main bearing races and bases for cylinder
is assembled.
mounts (fig. 32). The important item in crankcase assembly is the
adjustment of side play {clearance) for the flywheels, the mainshaft
roller bearings having already been selected and fitted (par. 25). THICKNESS GAGE 1
When assembling crankcase, it is best to support it on an open-end ~ 1
box with an opening about 8 x 8 inches, and at least 4 inches deep (see
fig. 7.6 for construction details) .
lA PO 310329
Figure 53-Checking EnJ Play ol Flywheels in Crankcase with

Gage (41-G-198)
b. Selecting and Fitting Thrust Collars. With right crankcase

supported on open box, and with gear shaft bearing spring ring en-
gaged in groove in roller race, install bearing washer and gear shaft
roller bearing assembly.
~~ (1) Select two thrust collars (between 0.080 and 0.090 inch) and
-~CAS< KA~IA
install them on flywheel hubs, making sure that collars register on
dowel pins and seat against flywheel faces (fig. 52). Both thrust collars
< PD >10m should be approximately the same thickness in order to keep flywheels
centered in crankcases and connecting rod upper ends centered be-
Figure 52-Measuring Thrust Washer Thickness with tween piston bosses.
Micrometer Calipers (41-C-301)
77
76
CHAPTER 3
(2) Install flywheel assembly in right side crankcase and install ENGINE (Cont'd)
roller bearing and bearing washer on sprocket shaft and install left
side crankcase. NOTE: No gasket is used between crankcase center Section VI
joint, nor should joint be shellacked as yet. Insert the two cap screws
at top of crankcases and two studs at bottom of crankcases and ENGINE ASSEMBLY
tighten to clamp cases securely together.
(3) With crankcase and flywheel assembly supported in vertical 38. ENGINE ASSEMBLY.
position, push back and forth on ends of sprocket and pinion shafts to a. Install Generator.
check end play of flywheel in crankcase. lf no end play is found, cases
must be disassembled and thinner thrust collars fitted to flywheels. (1) INSTALL GENERATOR IDLER GEAR. Install generator idler
Reassemble and again check end play. If it is found that flywheels gear and fiber end thrust washer on stud and retain with split lock
•
now have end play, continue check with end play gage (41-G-198) as nng.
I
follows: .' (2) INSPECT GENERATOR END GASKET. Make sure that paper
(4) Install end play gage on sprocket shaft (fig. 53), and adjust gasket used between generator end and gear case is in good condition.
gage pin to just touch crankcase when flywheel is pressed toward If not, replace and secure to generator end with shellac.
gear case side. Now push flywheel toward left side case and use a (3) USE PAPER SHIMS TO OBTAIN CORRECT GENERATOR GEAR
thickness gage to determine amount of flywheel end play. AND IDLER GEAR TOOTH CLEARANCE. If the original number of paper
(5) Correct flywheel end play is 0.012 to 0.014 inch, and can be shims are at hand, use them when installing generator. If original
obtained by installing thrust collars of correct thickness. paper shims are not available, then start out with three new shims,
(6) After selecting and installing thrust collars of correct thick- placed between generator and crankcase cradle. NOTE: Paper shims
ness, oil the main bearings and proceed with final assembly. Give are approximately 0.004-inch thick with hole located to line up with
both faces of crankcase center joint a moderate application of shellac. oil drain holes in generator frame and crankcase cradle. Later models
Allow shellac to air-dry a few minutes before assembling cases. may not have drain hole in generator frame. just a small amount of
grease applied to crankcase cradle will hold shims in place while in-
(7) Assemble crankcases, install all studs and cap screws and stalling generator.
tighten securely. Remember'; three of the crankcase studs, the one at
top center and 'the two bottom studs are drive-fit studs that locate (4) GENERATOR MOUNTING STRAP. With generator located in
crankcases in exact relation to each other. NOTE: These studs must cradle (oil drain hole alined with shim and cradle holes) , assemble
not be replaced with loose-fit studs. After crankcase assembly is com- curved washer, lock washer, and nut on strap end, but do not tighten
pleted, recheck to be sure flywheels have at least the specified mini- as yet.
mum, 0.012-inch end play. (5) TEMPORARILY INSTALL GENERATOR MOUNTING END SCREWS.
Inasmuch as gear case cover is not yet installed, suitable spacers
(nuts or collars) must be used under the heads of the two generator
mounting end screws, to equal the thickness of the gear case cover.
Tighten mounting screws snugly (not tight); then tighten generator
mounting strap nut. Loosen end mounting screws to allow generator
to adjust itself, and again tighten end mounting screws.
(6) INSPECT CLEARANCE BETWEEN GENERATOR AND IDLER GEAR
TEETH. Generator and idler gears must mesh so that gear teeth do
not bind at any point, yet are free with very small amount of lash.
If gears have considerable lash. remove paper shim (or shims) from
generator mounting cradle and check again. If gears do not have
sufficient lash, add paper shim (or shims) between generator and
mounting cradle. NOTE: Generator mounting strap end nut must
be securely tightened when making gear lash check.
b. Install Bearing Oil Seal Ring and Spring. The bearing oil
seal ring must be installed on pinion shaft with flat side facing roller
bearing, and hub side outward with driving lugs engaged in shaft
splines. The spring bears against oil seal ring and breather valve
spiral gear.
78 79
ENGINE ASSEMBLY
the shaft and engage spiral and sleeve gears so that sleeve timing hole
(1). ~NSTALL SPIRAL ~EAR. The breather pinion shaft spiral gear is located when pinion gear is in running position on the shaft.
and ptmon shaf~ are sphne-e~~aged and gear is a slip fit on pinion (1) Turn engine until timing mark is exactly in the center of the
s?aft. Install sptral gear on pm10n shaft against spring, with marked timing_inspection hole in left side crankcase (see inset in fig. 54).
stde outward.
(2) Push pinion and spiral gears inward. against pressure of the
(2) . INSTALL PINION GEAR. The pinion gear and pinion shaft spring, and try and engage spiral and breather sleeve gear teeth so
are ~p~e-engaged ~nd ge~r is a slip .fit on shaft. Install pinion gear that hole in sleeve is in center of housing slot when pinion gear outer
on ptmon shaft, agamst sptral gear, Wtth marked side outward. face is 71r. inch from gear case joint face (this is the actual location
c. Install Scavenger Pump and Breather Valve Assembly (fig. of the pinion and spiral gears on the pinion shaft when gear case cover
29). CAUTION: Locate the semicircular screen between breatlier is in place). It may require several attempts before spiral and sleeve
valve housing and crankcase port before installing scavenger and gears can be meshed to give desired results.
40000
.....
CRANKCASE
-
-
, ..........
IBR.EATHER VALVE BREATHER GEAR
ALSO DRIVl:S
SCAVENGER PVMP
,. .
BREATHER VALVE TIMING HOLE ....... Figure 55- Timing Gears Installed
IN CENTER OF BUSHING SLOT •• I'D 310217
{3) In summarizing the above breather timing instructions. refer
Figure 54- Timing lreatlter Valve to figure 54. Spiral gear must be so engaged with breather sleeve gear
that when flywheel mark is in center of inspection hole and pinion gear
breather assembly. A recess is machined in rear side of crankcase port is fYJ n-inch from joint face, timing hole in the sleeve registers in slot
chamber to accom~odate the screen which is retained in place by as shown.
breather valve housmg. The breather sleeve valve must be timed so (4) After timing breather valve, exercise care that timing gears are
that the. elongated ports in valve sleeve and crankcase aline at the not pulled out of mesh. permitting timing to change, while installing
correct time for proper scavenging of oil from engine crankcase. the valve timing gears.
(1) See that crankcase and pump body faces are clean and thnt e. Install Timing G(>ars. All timing (cam) gears are marked for
paper gasket is in place (a light film of grease will hold gasket 11\ correct valve timing when installed with marks in alinement. The
place), and install pump and breather assembly. Install the washer'! timing gears are ordinarily installed with one 0.006-inch thick steel
and nuts on studs and securely tighten nuts. shim washer behind each of the four cam gears and on outside of the
d. Time Breather Valve (fig. 54). In timing brftather valve, it will two front cylinder cam gears. Occasionally an engine may be found
be necessary to shift spiral and pinion gears outward and inward on 81
80
ENGINE ASSEMBLY
washers and nuts on the mounting studs. N ote that two of the nuts
are of the long extension type. T hese special nuts must be installed
L:.at was originally assembled with more than one spacing shim at on the studs from which they were originally removed . Tighten all
one or more points. In this case, reassemble with the same number of nuts securely.
washers found when disassembling. h . Install Pistons. Refer to paragraph 12 a .
(1) INSTALL THE CAM GEAR TRAIN IN THE F OLLOWING ORDER : i. Install Cylinders. Refer to paragraph 15 a.
(a) Rear cylinder exhaust cam. j . Install l~nition Cir<'uit Breaker and Time Ignition. Refer to
(b) Front cylinder intake cam. TM 9-879.
(c) Rear cylinder intake cam, alining marks with pinion, rear k. Install Cylinder H ead ami Gaskets. Refer to paragraph 15 d .
cylinder exhaust and front cylinder intake cam gear marks. I. Ins tall Carhuretor and Intake Pipe. Refer to paragraph 15 b.
(d) Front cylinder exhaust cam, alining mark with front cylinder m. Install and Test Reconditioned Engine. Engine should be
intake cam gear mark. This gear also meshes with generator idling installed in a vehicle test chassis (or in the original vehicle chassis)
(intermediate) gear. and adjusted. tuned, and tested for satisfactory operation before
being put back into service.
f. Install Timin~ Gt>ar Case Cover. When the gear case cover is
(1) INSTALL ENGINE. Refer to TM 9-879.
installed and all screws securely tightened, each cam gear should
have at least a "free running" fit and have not more than 0.005-inch (2) TEST RECONDITIONED ENGINE. Refer to paragraph 17.
end play between bushings. If cam gear bushings in crankcase and
gear case cover have been replaced, it may be necessary to remove
the tappet guides and check the end play of each cam gear with a
thickness gage.
(1) Before installing gear case cover, lay engine on its side and
pour 74 pint of engine oil over the timing gear train.
(2) Unless the old gear case cover gasket is in good condition,
fit a new gasket. CAUTION: Do not 6t a home-made gasket as this
gasket has holes especially located for oil passages, and if a !tole is
left out or put in the wrong location, the engine oiling system will not
function correctly.
(3) Remove the two generator end mounting screws (installed
while mounting generator) and place cover on gear case, tapping it
with a block of wood and hammer to make the register holes fully
engage the three dowel pins.
(4) Install all cover screws (the generator end screws included)
except hexagon head bolt which also holds oil feed pump, and tighten
securely.
(5) Turn engine and note whether or not it turns freely. If con-
siderable drag is noticeable, possibly too many steel shims have been
fitted to one or more cam gear shafts. In this case, make necessary
correction.
g. Install Oil Feed Pump. Examine gasket closely. If condition
of gasket is at least questionable. use a new gasket. Never use a
home-made gasket on the oil feed pump as leaving out one hole or
locating a hole in the wrong place may put engine oiling system
completely out of order.
( l) Install pump assembly on the mounting studs, turning engine
slowly and pressing lightly against pump until the driving dogs on
the rear exhau~t cam gear line up with and engage driving slots in
the oil pump rotor.
(2) Install hexagon head bolt and lock washer and the three lock
83
82
FITS AND TOLERANCES
accommodate oversize rollers. Replace steel bushing when necessary
lapping leaves it so large it will not refit with largest oversize rollers.
CHAPTER 3 (10) CRANKCASE SPROC,{ET SHAFT ROLLER RACE (STEEL).
Standard size, 1.376 inches. See (9) above.
ENGINE (Cont'd) (11) CRANK PIN. Standard size. 0.999 inch. Replace when Worn
0.0005 inch or at such time as roller path wear shoulder is evident.
Section VII
(12) CRANK PIN CONNECTING Roo BEARING CLEARANCE. Rollers
FITS AND TOLERANCES fitted to give 0.0007 to 0.001 inch clearance.
(13) CYLINDER BORE. Standard bore is 2.7445 to 2.7-t55 inches.
39. FITS AND T OLERANCES. (14) FLYWHEEL SIDE PLAY IN CRANKCASE. 0.012 to 0.014 inch.
a . The following list of fits, tolerances, and wear allowances are Adjustable by collars varying in thickness (0.066 to 0. 102 inch) in
accepted standards of p ractice to be followed when servicing and /or •
- steps of 0.004 inch.
rebuilding the WLA engine. I
(15) GEAR SHAFT. Standard size. 0.87 5 inch. Small end diameter,
(1) CAM GEAR END PLAY. Free running to 0.005 inch. 0.62425 inch. Replace when worn 0.0005 inch or at such time as roller
(2) CAM GEAR SHAFTS. Replace cam gear and shaft assembly, path wear shoulder is evident.
when shaft is worn in excess of 0.001 inch. (16) P ISTON CYLINDER H EAD CLEARANCE. Distance between
(a) Front cylinder exhaust camshaft, both ends 0.6867 5 inch. cylinder head and piston (at highest position) is ~ '14; to =~~~~ inch.
(b) Front cylinder intake camshaft, both ends 0.6867 5 inch. ( 17) PISTON D IAMETER AT B OTTOM OF SK IRT. S tandard size
(c) Rear cylinder intake camshafts; crankcase end 0.6867 5 inch, is 2.743 inches measured at bottom of skirt, front to rear, at right
timer end 1.12425 inch. a ngles to center line of pin .
(d) Rear cylinder exhaust camshafts ; crankcase end 0.68675 ( 18) PISTON CLEARANCE IN CYLINDER. Must have 0.0015 to
inch, oil pump drive end 0.7805 inch . 0.0025-inch clearance in the cylinder (standard or oversize). R eplace
wh en clearan ce exceeds 0.006 inch. A bove specifications apply only
(3) CAM GEAR SHAFT IN BUSHING CLEARANCE. 0.0005 to 0.001 to taper-cam ground piston, which is 0.0025 inch smaller at top of
inch. sk irt (underneath lower ring) than a t b ottom of the sk irt. T his clear-
(4) CAM GEAR BusHINGS. Replace when worn in excess of 0.002 ance ( 0.0015 to 0.0025 in ch) is not su fficient for a straight-cam
inch. ground piston.
(a) All cam gear bushings in crankcase, line reamed '~i 6 inch. ( 19) PISTON SIZES A VAILABLE. Standard, 0.010, 0.020, 0.030 and
(b) Front cylinder intake and exhaust cam bushings in gear case 0.040 inch oversizes available.
cover, line reamed • %6 inch. (20) P ISTON RING SIDE CLEARANCE IN PISTON GROOVE. 0.004
(c) Rear cylinder intake cam and timer drive bushing in gear inch. Maximum allowable clearance before new rin g (or piston) is
case cover, line reamed 1Ys inches. necessary, 0.006 inch .
(d) Rear cylinder exhaust cam and oiler drive bushing in gear (2 1) P ISTON RING GAP. 0.010 to 0.020-inch gap in cylin der .
case cover, line reamed :!%:! inch. (22) PISTON R ING S IZES AVAILABLE. Standard and 0.0 10, 0.020,
(5) CIRCUIT BREAKER POINT GAP. The gap should be 0.022 inch. 0.030, an d 0.040 inch oversize.
(6) CONNECTING Roo ROLLER RACES (STEEL). Standard size is (23) PISTON PIN. St andard size, 0.7915 inch diameter. Replace
1.5 inches. Lap when worn to true and smooth races and to accom- when w orn 0.0005 in ch.
modate oversize rollers. Replace rods when necessary lapping leaves (24) P ISTON P IN F tT IN P ISTON B OSSES. L ight han d press fi t .
races so large they will not refit with largest oversize rollers. (25) PISTON P IN CLEARANCE IN CONNECTING R OD B USHI NG.
(7) CONNECTING Roo PISTON PIN BUSHrNG. Standard hole 0.001 inch. M aximum allowable clearance before new oversize pin is
diameter 0.7925 inch. Ream and hone for oversize pin when pin n ecessary, 0.002 inch .
clear ance in bushing exceeds 0.002 inch. Replace to accommodate (26) P ISTON PIN S IZES A vAILABLE. Standard and 0.00'2, 0.004,
new piston fitted with standard pin. 0.006, 0.008, and 0.010 inch oversize.
(8) CONNECTING ROD SrDE PLAY BETWEEN FLYWHEELS. 0.006 to (27) ROLLERS, CRANK PIN. Two len gths used. Sta ndard size,
0.010 inch. 0.250 in ch diameter. Sh ort rollers for forked rod are 0.270 inch long.
(9) CRANKCASE GEAR SHAFT RoLLER RACE (STEEL). Standard T he long rollers for n arrow rod are 0.550 inch long.
size, 1.376 inches. Lap when worn to true and smooth race and to 85
84
•
CHAPTER 4
FUEL, INTAKE, AND EXHAUST SYSTEMS
(28) ROLLERS, GEAR SHAFT. Standard size 0.250 inch diameter.
Length, 0.550 inch. Section I
(29) ROLLERS, SPROCKET SHAFT. Standard size 0.250 inch.
Length 0.360 inch. DESCRIPTION OF SYSTEMS
(30) ROLLER SIZES AVAILABLE. Standard (0.250 in.) and in steps
of 0.0002, 0.0004, 0.0006, 0.0008, 0.001 inch oversize. 40. FUEL AND INTAKE SYSTEMS.
(31) SPARK PLUG GAP. 0.025 to 0.030 inch. a. Fuel System. The fuel supply is kept in the left side tank and
(32) SPROCKET SHAFT. Standard size. 0.87 5 inch. Replace when is gravity fed to the Linkert model M88 carburetor which is located
worn 0.0005 inch or at such time as roller path wear shoulder is between the engine cylinders. A supply valve is located in the tank
evident. and a strainer is located at carburetor bowl intake. The carburetor
is of the side-outlet, plain-tube type with a fixed venturi. Carburetor
(33) TIMING , IGNITION. Y,. to %2 inch before top dead center on
compression stroke.
(34) TIMING, BREATHER VALVE. See paragraph 38 d.
FLOAT SCREW
(35) TIMING, VALVES. Time by alining gear marks. Valve timing
by piston location: Intake opens %!! to ~~\:! inch before top dead FLOAT
center; intake closes :!~11 •1 to -1% 4 inch after bottom dead center. Ex-
haust valve opens :1 7J.14 to 4 % 1.1 inch after bottom dead center; exhaust
valve closes %:.! to ~(1 :! inch after top dead center.
(36) VALVE TAPPET CLEARANCE (ENGINE CoLD). Intake valves,
0.004 to 0.005 inch. Exhaust valves, 0.006 to 0.007 inch.
(37) VALVE TAPPET IN GUIDE CLEARANCE. 0.0005 to 0.001 inch.
Replace tappet and / or guide when clearance exceeds 0.002 inch.
(38) VALVE TAPPET GUIDES. Press fit in crankcase, 0.0005 to
0.001 inch.
(39) VALVE STEM IN CYLINDER GuiDE CLEARANCE. 0.0035 to
0.0055 inch. Replace valve and / or guide when clearance exceeds
BOWL ORAl N PLUG
0.008 inch.
....__FLOAT VALVE SEAT
' - - - FLOAT VALVE SEAT GASKET
L-._ _ FLOAT VALVE
L-----FLOAT VALVE BEARING PIN
RA PO 310390
f
. I Figure 56-Cross Section ol Catiwretor Floor Bowl

•
has two manual controls, the throttle, which is operated by the right
handlebar grip, a nd the choke, which is operated by a lever located
on the front side of the carburetor. The high speed fuel supply is
governed by a fixed (non-adjustable) jet. The idling to medium
speed, 30 miles per hour, fuel supply is governed by an adjustable
(low speed) needle valve located on the rear side of the carburetor
body.
(1) CARBURETOR FUEL CIRCUITS. The motorcycle carburetor
may be said to consist of four circuits. By describing and treating
each circuit separately, study and repair of the carburetor is made
easier.
(a) The Float Circuit (fig. 56). The float C'ircuit consists of the
87
86
DESCRIPTION OF SYSTEMS
(b) The High Speed Circuit (figs. 57 and 58). The high speed
circuit consists of the main nozzle, fuel well, air bleed, fixed metering
jet, fixed size venturi, and t.1e t.:uottle disk. As the throttle is opened,
the air flow over the main nozzle is increased, thus increasing the fuel
supply which is atomized and vaporized on its way into the engine
cylinders. The main nozzle is located in the narrowest part of the
venturi, where the air stream through the carburetor is traveling at
its greatest velocity.
SHORT NEEDLE VALVE

THROTTLE LEVER STOP SCR.EW1
LOW SPEED Ll FT
LEVER AND NEEDLE WEAR TAKE UP
VALVE ASSEMBLY SPRING
LIFT LEVER
ItA PO 310392 SPRING SEAT
IDLE SLOT
Figure 57-Fixed Jet for High Speed Circuit
.-BC)DY PLUGS
bowl, the float, fuel supply valve and seat, and the circular cork @
float and lever assembly. The float circuit automatically controls
the height of the fuel level in the bowl and also in the main nozzle.
SMALL
IDLE HOLE
Gf:\\'...-THROTTLE LEVER LIFT LEVER '=;:;;;,!;:::!/ SHAFT COLLAR

THROTTLE SHAFT TENSION SPRING
THROTTLE DISK IDLE HOLE FARTHEST
NOZZLE - -- -+J'l FROM FLANGE
INTERNAL NOZZLE VENT
VENTURI '-- IDLE CHANNELS
LOW SPEED NEEDLE
VAL.VE SEAT HOLE
0
ItA PD 310391
Figure 59-Needle Valve and Idle Channels for l.ow Speed Circuit
THROTTLE DISK (c) The Low Speed Circuit (fig. 59). The low speed circuit prin-
SCREWS cipal parts are: the metering jet, fuel well, idling (low speed) needle
and seat, supply channels and idle ports. The idling (low speed)
circuit controls the engine fuel supply during idling and light load
speeds up to approximately 30 miles per hour. The main metering
jet supplies fuel into the well (same as in the high speed circuit),
ItA PD 310393 but with the throttle in closed position, the fuel is drawn off past the
adjustable low speed needle valve, into the low speed channels (mixed
Figure 58-Section Showing Throttle Disk, Venturi and Spray Nozzle
89
88
~ -
-- - -
CHAPTER 4
with air from the low speed air bleed) into the carburetor bore
through small holes and a narrow slot located at the edge of the FUEL, INTAKE, AND EXHAUST SYSTEMS (Cont'd)
throttle disk. The adjustable low speed needle valve controls the
fuel supply f~eding into the low speed channels. As the throttle is Section II
o~n.ed, the atr stream through the venturi becomes more active, thus --
shtftmg from the low speed circuit to the high speed circuit. i CARBURETOR
. (d) The. Choke Circuit.. The cho_ke circuit is used to supply a
ncb fuel mtxtur_e, from whtch suffictent vapor will be obtained to 42. PRELIMINARY INSTRUCI'IONS.
start a cold e~gme. This circuit consists of a choke valve (disk) to a. By proper cleaning and replacing of worn and/ or damaged
close off practically all of the air supply through the carburetor bore parts the carburetor can be reconditioned good as new. Carbon
a shaft, lever, a:"d ca~ assembly. The cam allows the low speed (crust) formations in the barrel, around the throttle valve and in
:"eedle valve to nse off tts seat so that a richer mixture can reach the the small idle holes and slot affect engine speeds up to approximately
tdle holes. !he chok_e lever is provided with several stops for full 30 miles per hour. Usually a lean spot results and no manner of
choke, startmg, warmmg-up, and running positions. adjustment will correct it. Dirt in the low speed channels also makes
h. _Intake System. The intake system is extremely simple in that for a difficult carburetor adjustment. Extreme care must be exercised
all un~ts are ex?Osed, closely connected, and readily accessible for in carburetor repair because of the delicate balance necessary in
o~eratton~ servtce and/ or repair. The intake system consists of an metering the fuel into the low speed and high speed circuits. Wire,
otl bath atr clea~er, connecting hose, and carburetor intake fitting. or other metal objects of unknown dimensiqns must not be used to
Th~ carburetor atr and fuel passage connects with the two engine clean out passages, jets, and channels. Use the special tools provided
cylinders through a short intake pipe (manifold). for this delicate and precise work.
h. Complete Disassembly and Subdisassemhly. Very often it is
41. EXHAUST SYSTEM. not necessary to completely disassemble the carburetor for satisfac -
tory repairs. Carbon crust removal and a general cleaning will put
a. The exhaust system consists of a muffler and tail-piece the majority of carburetors back into dependable service. On the
assembl~, front exhaust pipe assembly, and rear exhaust pipe. Ex- other hand, worn throttle disk shaft, choke valve disk shaft, and any
haust p~pes. are a slip fit in cylinder exhaust ports. The exhaust other worn and/ or damaged parts must be replaced for best recon-
syst~m ts stmple and efficient and readily accessible for service or ditioning' job. If carburetor needs only a crust and general cleaning,
repatr.
remove bowl assembly, throttle valve disk and shaft, the idle hole
and fuel passage plugs and the low speed needle valve. Further dis-
assembly is not necessary.
43. DISASSEMBLY.
a. Progressive Disassembly.
(1) REMOVE BOWL ASSEMBLY. Remove the bowl retaining nut
and copper gasket and pull bowl assembly away from carburetor
body. NOTE : Bowl nut also retains sprinA which holds spray nozzle
in position in central tube.
(2) DISASSEMBLE BowL. Remove float valve chamber cap screw
and valve seat (bowl union nipple) and fiber washer from lower side
of float valve chamber. Remove the two screws which retain the float
lever and carefully withdraw the float and lever. Float valve will
either come out with float or will be free for removal. Remove the
bowl drain screw and fiber washer.
(3) REMOVE THROTTLE DISK. Before removing throttle disk
screws, back off lever stop screw so that throttle disk closes fully in
the carburetor barrel. Next, with a scriber, scratch a deep mark on
the throttle disk and also on the wall of the barrel for perfect register
(alinement of scribed marks) when reassembling carburetor. Remove
throttle disk screws and lock washers and pull disk out of slot in
throttle shaft. Exercise care not to damage disk when removing it
90 91
CARBUROOR
(8) HIGH SPEED FiXED jET. High speed fixed jet should not be
with pliers. Remove throttle shaft after loosening throttle lever clamp removed unless found in damaged condition or that the wrong jet is
screw. Take care not to lose the bronze helical spring located between in use. Model M88 carburetor uses fixed jet No. 1. If jet must be
body and lever. removed, see that screwdriver bit fits slot of jet perfectly and that
{4) REMOVE THE VENTURI (CHOKE TUBE). After spray nozzle neither the head, slot nor h ole are damaged when jet is removed.
has been removed from bottom of central fuel passage remove the
venturi. CAUTION : The venturi is made of soft m etal; do not dam- 44. CLEANING AND INSPECTION.
age it upon removal. Also note small bore end faces the choke valve a. Clean a ll carburet or parts (except cork float) carefully in dry-
in the barrel.
cleaning solvent. The carbo n crust formation within the barrel may
(5) REMOVE Low SPEED NEEDLE VALVE AND LIFT LEVER be scraped off with a suitable tool , taking care not to cut or damage
ASSEMBLY AFTER REMOVING PIVOT SCREW. Do not lose the small the parts, and the throttle disk may be rubbed on fine emery cloth
washer and spring located between the lift lever and the needle valve (on plane surface). After cleaning, wash parts in dry-cleaning
channel end. solvent.
b. Inspection. Inspect all parts for excessive wear and / or dam-
age. Any excessively worn and / or damaged parts should be r eplaced
IDLE CHANNEL HOLES OPEN to place carburetor back in first class condition.
(1) THROTTLE SHAFT AND BUSHINGS. Throttle shaft and body
bushing wear in excess of 0.004 inch will affect idling (closed throttle)
speeds. Standard throttle sh aft is 0.251 inch diameter. R eplace the
throttle shaft but do not replace the monel bushings.
(2) CHOKE VALVE SHAFT AND LIFTER CAM ASSEMBLY. When the
choke valve shaft shows wear shoulders or has in excess of 0.010 inch
clearance in body holes it should be replaced. Standard shaft is 0.251
inch diameter. Body holes are not bushed. If lifter cam on end of
shaft is excessively worn and / or damaged, replace shaft and cam
assembly.
LOW SPEED NEEDLE (3) LOW SPEED NEEDLE VALVE LIFTER LEVER AND P IVOT SCREW.
CHANNEL OPEN Lift lever h as %2 -inch hole and pivot stud is 0.276 inch in diameter,
giving 0.005 inch clearance. When clearance exceeds 0.010 inch,
FOR CLEANING replace. When spring and ball tension of lifter lever does not retain
IDLE HOLE PLUG
needle valve in selected position, replace the lever assembly.
HIGH SPEED REMOVED FOR
(4) Low SPEED NEEDLE VALVE. If the valve needle is bent or its
FIXED JET CLEANING point worn and damaged, replace the needle.
(5) SPRAY NozzLE. If spray nozzle is found damaged upon
RA PO ~HMOI r emoval, replace it .
(6) SPRAY NOZZLE SPRING. The spray nozzle spring may be
figure 60-lclle Cltannel Hole Screws oncllow Speed Needle Valve
Removed lor aeoning found rusted and stuck in the body hole. If so, replace it.
(7) VENTURI. If venturi is excessively loose in barrel and the
{6) REMOVE CHOKE VALVE SHAFT. After removing set screw hole through which the spray nozzle end passes is wom elongated,
which retains the lever and the two screws and washers which retain replace it. A loose fitting venturi will wear a groove around the spray
the disk, remove disk from shaft. A small steel ball and spring will nozzle end.
drop out of position when the choke lever is removed from the shaft. (8) CARBURETOR BODY. Inspect the body clo!>ely for condition
After pulling disk out of shaft slot, shaft with cam can be withdrawn of the small idle holes and the connecting slot, condition of idle
from carburetor body. passages and condition of all threaded holes.
(7) REMOVE IDLE HOLE AND CHANNEL PLUGS. Remove the idlt' (9) BowL AssEMBLY (fig. 56). Inspect the bowl {aluminum) for
hole, cover plug screw, and the two low speed cir cuit channel enct good condition, especially as to condition of threads.
plug screws (fig. 60) . Also plug screw located in central body tub<' (a) Inspect the cork float for logged condition; cracked, dis-
can be removed for "blowing out" passages. NOTE: Do not removo colored, or bad protecting finish. Inspect the float lever fingers for
the locking plug and short needle used to close o ff high speed needle excessive wear and inspect lever and float connection for security.
valve seat (fig. 57).
93
92
CARBURETOR
(b) Inspect the float valve and seat for wear. If seats a re ringed with celluloid cement or with thick shellac. Do not attempt to adjust
both valve and seat must be replaced. See that fiber washer between float level until cement or shellac seal bas thoroughly set.
valve seat and body is in good condition. (2) ADJUSTING FLOAT LEVEL. Hold the bowl upside down and
(c) Inspect float lever pin (retained in one of the pin cap screws) I , measure the distance from the float to the edge of the bowl (measure-
for wear. i I ment taken directly opposite float valve). Float should be Y4 inch
from edge of bowl (fig. 61 ). CAUTION: D o not bend float lever in
45. REPAIR. bowl to obtain correct settinA, as this procedure would bend the float
a. Clean Idle Holes and Passages (fig. 60). Use special carburetor lever fin~ers and cause lost motion between the lever and Boat valve.
tool (41-T-3081-45) when cleaning all carburetor holes and passages. Float and lever assembly must be removed from the bowl, and the
NOTE: Turn cleaning dri/Js by hand, being careful not to damaAe lever bent up or down, as required, to obtain the Y4 -inch float level
passaAes or seats. Before attempting to clean holes and passages, see distance.
that carbon crust is removed (par. 44 a) .
(1) CLEAN IDLE HOLES. For the large idle hole (farthest from CARBURETOR BOWL ASSEMBLY
flange end) use drill No. 55. For the small idle hole (nearest flange
end), use No. 70 drill. Clean the connecting slot between the large -
and small idle holes with special tool having a 0.009-inch thick blade. '
I:
I
(2) CLEAN IDLE CHANNELS. Use the No. 42 drill to clean out
idle channels. CAUTION: When cleaning out the vertical idle channel
do not completely "bottom" the driJJ, as doing so may damaAe the -
low speed needle seat, thus ruining carburetor body beyond repair. I
I
(3) CLEAN Low SPEED NEEDLE VALVE SEAT HOLE. Use drill
No. S3L, passing it down into needle channel until it bottoms; then
tum drill with fingers to clean out hole.
(4) UsE OF DRILL IN HIGH SPEED jET HOLE. Never under any
circumstances should a drill or hard object be used to clean out high
speed jet hole. Doing so would alter the metering of the fuel and CORK FLOAT
throw carburetor out of adjustment. If high speed jet appears in bad
condition (damage from screwdriver or tampering) replace it with
a new No. 1 jet.
(5) CLEAN WITH COMPRESSED AIR. Blow out all holes, nozzles,
jets and channels with compressed air and wash all parts in clean
gasoline.
b. Replace Throttle Shaft. The monel metal throttle shaft bush-
ings need not be replaced during the life of the carburetor. The RA I'D 310356
throttle shaft can be replaced, however, at the time the carburetor is
reassembled. figure 61-Mecrsuring Floor Setting in Bowl
c. Replace Float. Remove old float by cutting seal (varnish or
shellac) around float screw which fastens float to float lever. The (3) FLOAT VALVE HEAD AND LEVER FINGER CLEARANCE. Before
seal can be cut with a pocketknife. Remove float screw and assemble carburetor is assembled, see that float valve head is a free fit between
new float to the lever. This should be done with float valve, float the fingers of the lever with not more than approximately 0.003- inch
valve lever, float hinge pin, and float valve seat and gasket assembled free play. Check this clearance after float and lever assembly is
in bowl. Before tightening float screw securely, adjust as follows: assembled in the bowl by carefully placing a small screwdriver
(1) ADJUSTING FLOAT OFFSET IN BowL. The float must be offset against the valve head to hold the valve firmly against the seat, yet
to one side to provide body clearance as float raises and lowers in not bind the lever. Moving the lever up and. down will reveal amount
the bowl. Looking down the bowl (gasoline inlet side away from you), of actual clearance between the valve head and the lever fingers.
pull the float toward you to the limit of the slot in the lever, and NOTE: If the Boat valve head and lever finger clearance is excessive,
then shift (offset) about lft 6 -inch to the left of the center line. Tighten the float mechanism will not feed properly. After the float and lever
float screw securely. have been assembled to the bowl, see that the float is approximately
(a) Cement the top of the float screw to the float (form a seal) square with the top of the bowl.
94 95
CARBURETOR
46. ASSEMBLY. 47. SPECIFICATIONS FOR LINKER MODEL M88
a. Install Throttle Shaft and Throttle Disk. Install the throttle· CARBURETOR.
shaft and pass the throttle disk through the shaft slot so that counter a. Data.
bored set screw holes and the scribed mark face the flange end of the-
carburetor body. The throttle disk must close tightly in the carbu
.
Indentification . . . . . . . . . . . . . (Model No. MBB stamped on top)
Size . . . .. . .. . . . 1}'4 inches (actual barrel dia 1% in.)
retor barrel. Close the throttle disk, making sure the scribed mark
Venturi .. .. ... . .. .. .. . .. .. . ... . . . . . . 1St .
· 11 G ln.
on disk lines up with scribed mark in the barrel (if new disk 1S
Small idle hole . . . . . . . . . . . . . . . ..... . ... . . . . . No. 70 drill
installed, disregard this) , press upward on the shaft so that collar
Large idle hole . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . No. 55 drill
bears against the carburetor body and tighten the disk screws. Try
Idle slot (between holes) . . . . . . . . ... Use 0.009-inch blade
opening and closing the throttle disk to see that it does not bind, anrl . . Vertical and diagonal idle channels . . ' . . . . . .
also closes off the barrel hole completely. Install throttle shaft wear I. .I
No. 42 drill
Low speed needle valve seat .. . . . . . . .. . . . . No. 53L drill
take-up spring on shaft and install the throttle lever. Open throttl(' High speed jet (fixed) • 0 • • • • • • No. 1
wide open in the barrel and clamp the throttle lever on the shaft
with wide open stop against the body stop. Throttle lever and shaft
should open and close with just slight drag.
b. Install Choke Valve, Shaft and Lever Assembly. Install -
choke valve shaft so that cam is on rear side of body. The lever stop
ball should be installed as follows: As the shaft is passed through the
I
body holes, have lever stop notch ball located on end of spring and
held in place by one of the notches in the lever stop, then pass shaft
.
through body and engage the lever hole. Install the lever retaining I
screw and install choke valve disk in shaft slot with hole at bottom
of barrel. Close choke and tighten valve retaining screws.
c. Install Low Speed Needle Valve and Lifter Lever Assembly.
Locate the tension spring and spring seat (washer with shoulder) on
the needle valve with washer shoulder toward spring. CAUTION
The lifter lever sprin~ seat (washer) limits the amount ol air bleed
to the idle circuit and must be in place; otherwise the carburetor
cannot be adjusted lor satisfactory en~ine idlin~. Engage needle in
body channel and press down on lifter lever assembly so that pivot
screw can be installed.
d. Install All Channel Opening Plug Screws. Install idle hole
plug screw and the two body channel plug screws.
e. Install Spray Nozzle and Venturi. Install venturi with choke
end near carburetor flange and pass spray nozzle up through body
channel until end of nozzle seats in venturi hole. Spray nozzle is
retained by spring and bowl nut.
f. Install Bowl Assembly. Install spray nozzle retaining sprin&
in body hole, locate bowl assembly on body, install copper washer,
and turn on bowl retaining nut: See that bowl fuel line nipple is in
correct position and tighten bowl nut,
96 97
CHAPTER 4
CHAPTER 4
FUEL, INTAKE, AND EXHAUST SYSTEMS (Cont'd)
FUEL, INTAKE, AND EXHAUST SYSTEMS (Cont'd)
Section IV
Section Ill
INTAKE PIPE, AIR CLEANER, AND FITTINGS
FUEL STRAINER AND FUEL SUPPLY VALVE
50. 11\TAKE PIPE (MANIFOLD).
48. FUEL STil.AINER. a. The intake pipe connects between the two cylinders and sup-
a. The only repair necessary to the fuel strainer is the replace- ports the carburetor. Gland nuts and packing bushings secure the
ment of the screen, cork washers, or the retaining cap. A damaged inlet pipe to the cylinder nipples, making a n airtight joint. The
housing (bad threads, etc.) should be replaced. carburetor is mounted on inlet pipe flange with four cap screws.
49. FUEL SUPPLY VALVE. 51. AIR CLEANER AND FITTINGS.

a. Description. The fuel supply valve, located in left tank for- a. Description. The air cleaner is mounted on a bracket on the
ward position, is a two-purpose valve, serving as a shut-off and also left side of the vehicle, near battery box, and is connected to the
controlling reserve fuel supply of approximately 3 quarts. When valve carburetor by means of a flexible hose, carburetor end fitting, and
is turned down. finger-tight, the fuel supply is shut-off. When clamps. The air cleaner contains two filter elements, retained by a
loosened fully, the valve is normally open. When in the open position baffle plate and thumb screw. enclosed by the oil cup. The oil cup
and lifted to the limit of its travel, the valve releases the reserve is retained in position by two spring clips. Gaskets are located above
fuel supply. the filter elements and between the body and cup to prevent leakage.
b. Repair. About the only thing that requires replacement (out- b. Disassembly. Unlatch oil cup retaining clips. remove oil cup,
side of damaged parts) in the fuel valve, is the rubber seal washer, and after removing the baffle plate, the filter elements can be with-
located at the upper end (under valve knob) of the rod. This rubber drawn from the body. If filter elements stick in the body, use a piece
seal offers resistance to the rod and retains it in the raised position of hooked wire to assist in their removal.
for reserve fuel supply use. c. Cleaning and Ins peetio n. Clean all parts in dry-cleaning
( 1) REPLACE RUBBER SEAL WASHER. Remove the screw which solvent and inspect for good condition.
retains knob on the end of the valve rod. Unscrew the knurled upper d . Repair of Cleaner. If body is badly dented, twisted, or in
seat cap. Remove plain washer, spring, and rubber seal. Install otherwise bad condition, it should be replaced. D amaged filter units,
rubber seal with cone side down and retajn with spring, flat washer, gaskets, baffle plate, and oil cup should also be replaced. Broken or
and seat cap. Assemble knob on end of rod and retain with screw. damaged latches and springs can be easily replaced.
(2) REMOVE AND INSTALL VALVE Roo. Valve rod must be re- (1) REPAIR OF FITTINGS. Damaged air cleaner connecting hose,
moved and installed from underside of tank. hose clamps, and/ or carburetor fittings should be replaced.
(a) R emove. Close valve, remove knob and remove valve nipple e. Assembly. See that the two gaskets are in good condition and
from tank. Rod will pull out of tank when nipple is removed. are in place before assembling the air cleaner. Install filter units and
(b) Install. At time valve rod and nipple are assembled to tank, retain with baffle plate. Attach the oil cup to the filter body by means
see that the two nipple washers (one on either side of spacer) are in of the spring latches. It should seat firmly and squarely against
good condition. Assemble knob to upper end of rod and retain with gasket in body groove. See that the latch springs fully engage the
screw. lip of the oil cup.
98 99
\
CHAPTER S
CHAPTER 4 IGNITION SYSTEM
FUEL, INTAKE, AND EXHAUST SYSTEMS (Cont'd) 5-l. DESCRIPTION.
a . Desrription (fig. 62). T his ignition system differs from the
Section V conventional automotive types, in that tt has no high tension rotor
EXHAUST SYSTEM or distributor cap. A circuit breaker (timer) alone is used. H igh
tension cables lead dtrectly from the spark coil secondary winding
ends to the spark plugs, both plugs sparking at t he same time. When
52. MUFFLER. one cylinder is on a compression stroke (ready for ignition). the other
a . The muffler a nd tail piece (fish tail) are m&de integral and cylinder is on an exhaust stroke; thus only one cylinder fires when
repair to this assembly is not practical. The muffler end, however, the circuit breaker points are opened . No. 3 spark plugs are used.
must be kept open and free from caked mud (or other matter) which
will restrict the outlet of the burned gases. No &ttempt should be 55. CIRCUIT BREAKER (TIMEH. ) DISASSEMBLY.
made· to clean the inside of the muffler, cut off end of fish tail or
enlarge fish tail holes. A badly damaged muffler and / or tail piece . ~ a. Circuit breaker can be disassembled for replacement of timer
must be replaced. I . base, timer shaft, and spiral gea t• (fig. 63) . The circuit breaker timer
•
head mounts the circuit breaker lever, adjustable contact point, and
condenser which are readily accessible (on or off the vehicle) for
53. EXHAUST PIPES. adjustment and / or replacement when timer cover is removed. Timer
a. The front cylinder exhaust pipe with connection for the rear base bushings are not replacable.
cylinder exhaust pipe is of welded, one-piece construction and when ( 1) REMOVE TIMER SHAFT. R emove the pin from spiral gear hub
found in badly damaged condition must be replaced. A badly dented and drift or press the timer shaft out of gear. Withdraw timer shaft
exhaust pipe will restrict exhaust gases and cause engine overheating. from base. Do not lose stt:el spacer washer located between gear and
When the rear cylinder exhaust pipe is bent, dented, and damaged
housing.
to the extent it does not fit the cylinder port or pipe " V " connection,
and offers too much restriction to the exhaust gases, it must be (2) DISASSEMBLE C IRCUIT BREAKER ( T IMER) H EAD. If exami-
r eplaced. nation of the circuit breaker head components show it to be necessary,
disassemble the unit as follows (fig. 64):
I (a) Remove Circuit Breaker Lever. Remove n uts from condenser
and terminal binding post to free the pig tail brass terminal strip.
r
I
- Remove the lever spring and lift the lever from its insulated pivot
stud.
(b) Remove Adjustable Contact Point. Remove the two lock
-
•
'
•
-
-
screws and plate and adjustable contact point assembly is free for
removal.
(c) Remove Condenser. After end nut and washers which secure
the circuit breaker lever pig tail brass terminal strip are removed,
i
'•
- remove the condenser mounting screw (this screw also grounds
condenser to the timer head) .
(d) Remove the Coil-to- Timer Wire. If inspection shows it to
be necessary to replace the coil-to-timer shielded wire, simply remove
terminal stud nut and washer and remove wire.
(e) Timer Head Insulated Terminal Stud. Unless inspection
!:haws that the timer head insulated terminal stud (secures the coil-
to-timer wire, underneath the timer head, and circuit breaker lever
pig tail brass terminal strip, on top of the timer head) is in bad
condition, or that insulation is defective, it is not necessary to remove
and/ or replace this part.
101
100
IGNITION SYSTEM
------------~~-10
BLACK
6
COVER---+~\
RETAINER
~--GREEN 33
COVE R-----'~
RED
I TIMER LEVER
RED- BLACK - -.
* ·----+:
D ' I
I
I
I
. ,. ., *
.,...._,. A
/
12
...~ BLACK ,
BA SE SCREW S
I
/
/
/
*"
c
..,------:...... . .
HEAD TENSION
LEGEND
(GROI'NO) SPRING
I t o 7- SWITCH TERMINALS
10-SIGNAL LIGHT TERMINAL
12- BATTERY POSITIVt TERMINAL
*
*A-COIL SHIELDING GROUND
B-COIL-FRAME-ENGINE
SHIELDING GROUND
13- BATTERY NEGATIVE TERMINAL * B-COIL-FRAM.E-ENGINE SH IELDING
18-FROI-.JT JUNCTION TERMINAL GROUND
!UNDER SADDLE)
26-IGN IT ION-LIGHT SWITCH
28-IGNITION COIL
*
* C-NOISE SUPPRESSION CONDENSER
D-SH IELDED COIL-TO-CIRCU IT
BREAKER WIRE
~~ -IGNITION CIRCUIT BREAKER * D-SHIELDED COIL-TO-CIRCUIT
34-COIL-TO-C IRCUIT BREAKER WIRE BREAKER WIRE
* E-SPARK PLUG SUPPRESSORS
ItA I'D 310317
RA PO 3 10249
Figure 62-lgnition Circuit Diagram
Figure 63-lgnition Timer Disassembled
102
103
IGNITION SYSTEM
(3) COIL-TO-TtMER WtRE. One en d of the metal shtelding on
56. CIRCUIT BREAKER CLEANING AND INSPECTION. the coil-to-timer wire must be grounded u n d ( r the head of one of the
a. Cleaning. Clean all parts in dry-cleaning solvent th at will not base mounting screws. In ,.rdtr that th(• cotl-to -timer wire_ will be
injure wire insulation or fiber and bakelite components. free within the head for retard and advance movement, the w1re must
b. Inspection. Inspect all parts for good condition and signs of - be connected to the msulated tenmnal post and coil within the head.
wear. The timer base bushings are concentrically bored after installa- '
.
tion, therefore, it is not advisable to replace these bushings. A new BREAKER LEVER TOOTHED LOCK WASHER
timer shaft will usually place the unit in good-as-new condition. AND PIGTAIL PLAIN WASHER
Circuit breaker points must be square, not pitted, and in good condi- CONNECTION
tion. The circuit breaker lever pivot stud insulation should be FIBRE WASHER
inspected for broken, worn, and/ or missing components. Stud and TERMINAL NUT
insulation are not replacable. The condenser should be tested on a ,-;;:,/
~ NUT AND
condenser tester, although actual operation on the engine is the LOCK WASHER
surest, most dependable test.
(1) TIMER BASE AND SHAFT CLEARANCE. Clearance between timer
shaft and bushings within base is 0.0015 inch.
(2) SPIRAL GEAR. Inspect the timer spiral gear teeth for signs of
wear and/ or damage. ADJUSTABLE
(3) TIMER HEAD AND TIMER BASE FJT. Try the timer head on CONTACT
POINT CONDENSER MTG.
the timer base for a free turning (not loose) fit. If the head has too
PLATE SCREW AND
much clearance on the base, the circuit breaker point gap will vary
WASHER
as the head is shifted for spark control.
CONDENSER
57. CIRCUIT BREAKER REPAIR.
a. Replace any worn and / or damaged parts that will affect the
operation of the circuit breaker as a whole. See that the circuit LOW TENSION
breaker points are in good condition and face squarely. See that the TERMINAL
coil-to-timer wire (shielded for radio noise suppression) is in good
COIL-TO-TIMER WIRE
condition. Make sure that insulation of the terminal post and the BREAKER
circuit breaker lever is in proper order of assembly and is in good LEVER BEARING GROUND TERMINAL
condition. STUD !INSULATED) FOR SHIELDING
TERMINAL INSULATION
58. CIRCUIT BREAKER ASSEMBLY.
a. Assemble the timer base and shaft and adjust end clearance WASHER AND NUT
of shaft in timer base. Assemble circuit breaker points to timer head
and install and connect the condenser. •• ,0 310416
(1) ASSEMBLE TIMER SHAFT AND TIMER BASE. When assembling Figure 64-lgnition Timer Heod Disassembled
timer shaft and timer base, select a steel washer (between spiral gear
and base) that will give a free running fit to 0.005-inch end play. End
59. IG NITION COIL CABLE REPLACEMENT.
play in excess of 0.005-inch will affect the ignition timing. Secure tht•
spiral gear to the timer shaft with the steel pin, riveted in place. a. Inspect the high tension cables for cracked and/or damag~d
insulation, particularly at the sealing nuts where cables enter the co1l.
(2) ASSEMBLE CIRCUIT BREAKER POINTS AND CONDENSER TO
TIMER HEAD (fig. 64). Install the adustable circuit breaker point The insulation on high tension cables sometimes becomes cracked
first and retain with the lock plate and screws. Install the circUit or otherwise damaged, allowing the high tension current to short to
breaker lever, making sure that spring is in position and that pig toil metal parts with which the cables come in co_nta~t. Trouble due to
brass terminal plate is secured to the insulated binding post. Instull this condition is most noticeable when operatmg tn wet weather or
the condenser and see that fiber and spacer washers are in proper just after vehicle has been washed. Replacin_g. high ~ension cables is
order of assembly, with the brass terminal plate on the condenst-r the only repair that can be made to the igmt!On cotl. If faulty per-
terminal stud; then install and tighten nut.
105
104
r
CHAPTER 6
formance of coil is not corrected by replacement of cables, then tlw GENERATING SYSTEM
coil unit must be replaced.
b. Replacin g Cables. Coil cable ends are embedded in sealing 61. DESCRIPTION OF ~YSTEM.
compound for insulation and waterproofing and cable replacement
must be done quickly and correctly as follows : a . ·T he generating system consists of the 6-volt , shunt-wound,
third-brush and " lamp-load" regulated generator, the storage battery
( 1) WARM THE COIL. Warm the coil slightly by turning on the
and the relay. One of the two field coils (shunt coil) is cont:olled by
ignition switch (if coil is in vehicle) and turning engine so that points the lighting circuit to increase the current outpu~ when et_the_r. the
are closed, or by connecting a 6-volt battery to the coil primary running service light or the blackout light are turned o_n. T?e tgrution-
terminals. This generates heat in the coil primary winding and softens light switch cuts in the field shunt coil for the ~ervtce hght, and a
the sealing compound. CAUTION: Do not heat coil to a higher
magnetic field switch cuts in the field shunt. cot! fo: th~ blacko~t
degree than just warm, otherwise the sealing compound wt/1 become light. Maximum charge rate of 4 amperes (With serVICe light on) ts
too soft and the holes will close up when the old cables are removed. sufficient to keep the battery in a good state of charge under normal
(2) PREPARE THE NEW CABLES. Have new cables ready to be service conditions.
inserted immediately when the old cables are withdrawn. The new
cable ends that insert into the coil must be trimmed and rounded
b. The generating circuit is illustrated in figure 65.
so they will follow through the holes (left in the sealing compound
by the old cables) without catching and jamming. 62. GENERATOR DI SASS£)1RI.Y.
(3) REMOVE OLD CABLES. After the coil is warm (not hot) un- a . Gen e r a l. The generator field coils give very little trou ble and
screw the cable seal nuts and pull out the cables one at a time. it is advisable to test them before removing them from the generat or
( 4) INSTALL NEw CABLES. As each cable is pulled out of the coil frame. If the coils test satisfactorily. this will simplify generator
((3) above). quickly transfer the seal nut and rubber packing washer repair. T o test field coils within the generator frame refer to para-
to the new cable. Insert a piece of stiff wire into the coil cable hole graph 63.
and measure the distance from the coil end to the cable seat (bottom b . Disassembly (figs. 66 and 67).
of hole) . Mark the new cable accordingly. Dip the end of the new ( I) REMOVE GENERATOR END COVER. This exposes brushes,
cable in very light oil or gasoline and quickly push it into the coil. brush holders, field coil connections, and commutator.
Make sure it is pushed all the way into its seat as per the mark made (2) REMOVE REGULATING (TH IN) BRUSH. Press downward and
on the cable. After cables are inserted. turn the seal nuts down tight outward (toward end of generator) on the brush spring retainer to
against the rubber packing washers to effect a watertight seal. free brush and spring assembly.
(3) REMOVE MAIN (THICK) BRUSHES. Remove the field coil
60. SPARK PLUG CLEAI\I NG A.~D ADJUSTING. terminal screws from the main brush holders. After screws are r~
a. Do not disassemble spark plugs for cleaning or replacement moved, the brush and sprin g assemblies can be removed from the1r
of core. Clean with a sand-blast cleaner and adjust the base electrode holders.
(never bend the central electrode) to give a 0.025 to 0.030-inch gap. (4) DISCONNECT REMAINING FIELD COIL ~ERMINALS. Discon~ect
Good spark plugs are most important for dependable and efficient field coil terminal screws from the regulatmg brush and swttch
engine performance, therefore, replace defective or questionable spark terminal plates.
plugs with No. 3 plugs.
(5) REMOVE DRIVE GEAR. Drift the pin out of the drive gear
a nd remove gear, spring and oil deflector from the armature shaft.
(6) M OUNT GENERATOR. Clamp the ~rmatur~ ~haft in copper-
faced vise jaws, with generator in upnght pos1tton to work on
com mutator end.
( 7) R EMOVE OUTER GREASE RETAINER. Remov e the th~ee screws
which retain the outer grease cover, gasket and the regulatmg brush
holder. B earing and end of armature shaft are exposed after outer
grease cover is removed.
(8) REMOVE ARMATURE SHAFT END NuT. Use ~i 6 -inch socket
wrench and remove armature shaft lock nut and washer.
(9) REMOVE BEARING HOUSING. Drift the bearin~ housing off .of
generator en d casting, striking the end of the housmg on oppostte
107
106
Q S T T v
SHUNT COIL ·
(WHITE MARK) ..t;i.
....
0
AL-\ '- _ \-AL BB AH AJ
AM --~ V :--:?i~ ~-AM
AN ® ®-AN
AO .. ~
~
.,.,.._AO
REGULATING COIL J
AP--\:6 $~AP
(ORANGE MARK)
RA PO 310323
Figure 66-Generotor, Disos.semhled
A-DRIVE GEAR PIN R- NUT (2) AG-GASKET

8 -DRIVE GEAR S-WASHER (2) AH-OUTER GREASE RETAINER
C-SPRING T -NEGATIVE BRUSH HOLDER SCREW (2) AJ-SCREWS
D-Oll DEFLECTOR
U -MA IN BRUSH ASSEMBLY (2) AK -FRAME END CASTING
E-DRIVE END BEARING (LARGE)
V -MAIN BRUSH HOlDER (2) AL-TERMINAl SCREW (2)
F-SPRING RING
W- INNER GREASE RETAINER AM- INSULATING BUSHING (2) Q
G-FELT Oil RETAINER
AN-INSULATING WASHER (2)
z"'
...... H-FRAME END SCREW (2)
X-GASKET
,..
"'
~
- z-
Y-COMMUTATOR END BEARING AO-TOOTHED LOCK WASHER {2) -4
J-PQLE SHOE SCREW (4)
Z-SPACING SHIM, 0.020 IN. THICK AP-TERM INAL SCREW NUT (4) Q
~
K-SHUNT FIELD COil {WHITE MARK)
A9 -POSITIVE BRUSH HOLDER INSULATION
AA -SPRING RING (1·5/16 IN. DIA.) Cll
L-POlE SHOE (2) -4
M -GENER1ATOR fRAME
AB-BEAR ING HOUSING
AR-SHUNT FIELD TERMINAl INSULATION {2)
"'J
AS-SHUNT FIELD TERMINAL
AC -WASHER
N-ARMATURE ASSEMBLY
AT-FIELD TERMINAl SCREWS (4)
0-ARMATURE SPACERS, 0.025 IN. THICK AD-ARMATURE END NUT
AU -REGULAT ING FIElD COIL
P-ARMATURE BAKEliTE WASHER AE-REGULATING BRUSH ASSEMBLY (ORANGE MARK)
9 -ARMATURE SPACER, 0.072 IN. THICK AF-REGULATING BRUSH HOLDER
RA PO 31 03238
Legend for Figure 66-Generator, Disassembled
GENERATING SYSTEM
nil components and electrical tests to determine condjtion of the
ormature field coils, brush holders. and terminal binding posts.
REMOVING ARMA- ( 1) INSPECT AND TEST A~MATURE . Inspect for condition of
TURE END NUT - wiring, commutator, shaft ends, and bearing seats. Observe whether
or not core laminatiol)s have been striking pole shoes and are bent
DRIVE GEAR REGULATING

BRUSH HOLDER •
I
IVE GEAR PIN I .
A- REMOVING DRIVE GEAR PIN 8-REMOVE ARMATURE END HUT.

WITH DRIFT. BRUSHES REMOVED.
GENERATOR END
CASTING -
BEARING HOUSING ,,
FRAME END SCREWS

SECURE' END CASTING
C-REMOVE THE TWO LONG D REMOVE BEARING HOUSING
FRAME END SCREWS. WITH DRIFT OR PULLER.
END CASTING REMOVED 1 .

1 ' •
'
fiELD COil
RA PO 310339
Figure 68-R.emoving Generator Field Coils
or damaged. If commutator is brush worn until it will require

removal of :!~{:! inch of metal to true it, replace the armature assembly.
Before testing the armature on a growler, make sure that the· com-
RA PO 310)49
mutator is free from carbon and copper dust deposits. Clean thor-
~EMOVE GENERATOR END F-fREE ARMATURE FROM FRAMI oughly between segments and at ends of commutator, blow off with
CASTING. BEARING FOR REMOVAL compressed air and proceed to test as follows:
(a) Test Armature and Commutator for Ground (fig. 69). The
Figure 67 -Disassembling GeneratOI' commutator and the armature coil windings must be insulated from
112 113
-
- ----
GENERATING SYSTEM
the metal core and shaft. Tum the growler on and touch one test and break contact between the segments with the hacksaw blade. A
prod to the metal core and the other test prod to several of the com- strong flash should be seen as contact is broken. No flash or a very
mutator segments (bars). If a ground exists, the circuit will be weak flash indicates an open circuit. Repeat this test between all
completed and so indicated by the growler. If no ground exists segments. If an open circuit is indicated, inspect for loose or broken
(circuit is open), there will be no indication by the growler. Replace wires at commutator connections. If none are found that can be
a grounded armature. repaired. replace armature assembly and commutator assembly.
TEST PRODS (2) TEST REGULATING FIELD COIL. Use a fully charged 6-volt
, .l storage battery, an accurate ammeter (3-ampere scale preferable)
'
HACKSAW BLADE
.....
-
•
•
'
•
• •
•
• U 11'0 31 OHO
figure 69- Testing for Grounded Coils and Commutator

RA PO 310321
Using Growler (41-G-5940)
figure 10- Testing for Shorted Armature Coils
(b) Test Armature for Short (fig. 70). Place the armature in Using Growler (41-G-5940)
growler and hold a piece of hacksaw blade in loose contact with the
armature core. Turn growler on. Rotate the armature slowly, one
and a pair of test prods. This is a current draw test and results will
or more full turns. If the armature is shorted, the piece of hacksaw
depend upon condition of battery and accuracy of the ammeter. The
blade will be attracted to the armature core and will vibrate violently
regulating field coil is located in the upper side of t~ frame and is
at one or more points around the armature. If short is found and identified by an orange pgint mark.
cannot be eliminated, replace armature assembly.
(c) Test Armature for Open (fig. 71). Turn growler on. Insert tip (a) Test for Open or Internal Short (fiA. 72). With tester, battery
of hacksaw blade between the segments that are closed in alinement and test prods correctly connected, touch the coil and terminals of
with the point of contact of armature core and the growler V. Make the coil. Tester should register 1.4 to 1.9 amperes. If no ~ester reading
114 115
GENERATING SYSTEM
is recorded. field coil is open. If t ester reading exceeds 2.2 amperes,
the coil is shortt-d. R eplace the coil.
(b) Te:;t lor Ground. T ouch one of the coil end ter minals with
one test prod and touch the generator frame with the other test prod.
Ammeter should register " NO READING.'' If a reading is observed .
coil is grounded to the generator frame and must be replaced.
- TC>U01 COIL
LEAD TERMINAlS
RA PO 310343
Fi9ure 12- Testing Fie ld Coil for Open or Internal Short

t l (Tester 41-T-5575)
TOUCH EA01
COIL TERMINAL
RA PD. 310 122

Figure 1J- Testing for Open Coils in Armature
Using Growler (41-G- 5 9 40)
RA PO 310342
(c) Test Shunt Field Coil (figs. 72 and 73). Follow same procedure Figure 13 - Testing Field Coil lor Ground to Generator Frame
outlined in (2) (a) above. The shunt field coil is located in the lower (Tester 41-T-5515)
side of the frame and is identified by a white paint mark. A high<·r
resistance winding is used in the shunt .::oil and the normal current
reading will be less. A normal coil will draw from 0.6 to 1.0 ampere the other test prod. Circuit should be open. If a ground is indicated,
If tester reading exceeds 1.5 amperes. it is shorted within and mu~t remove and reinsulate affected parts.
be replaced. M ake ground test per instructions in (b) above. c. lnsp ecl Be arings. T horoughly clean bearings in dry-cleaning
(d) T est Positive Brush Holder and Terminal Posts for Ground solvent and inspect for wear. If a bearing shows ex~essive wear
(fig. 74). The positive brush holder and the · two terminal posts art• (looseness). replace it. Bearing must be a snug fit (light press fit) on
insulated from the generator frame. Touch frame with one test prod the armature shaft and the outer race should be a slip fit within its
and the positive brush holder and terminal posts respectively with housing.
116 117
J
GENERATING SYSTEM
l•l. GENEHATOR REPAIR •
•
u. N o attempt should be made to repair the armature windings
•
' ' unl<'ss the break and / or damage is external a nd can be satisfactorily
rc•paired. The commutator cannot be replaced. Therefore, any serious
damage to either the commutator windings, core or shaft will neces-
GROUND
sitate replacement of the unit. F aulty and/or damaged field coils
ON CASTING lllUSt also be replaced. Damage to other parts will be obvious a"d
replacement made.
b. Turning ancl Truing Commutator. If the commutator is worn
and irregular, it must be turned on a lathe and smoothed with 2/ 0
lhnt paper. When turning and truing a commutator. the armature
shaft must be m ounted on it:> bearings. D o not use shaft cent ers.
NOTE : If the commutator is badly grooved by brush wear (groo ve
exceeds :1;::! in.) the armature and commuta tor assembly must be
replaced.
<:. Undercu tting Commutator Mica. Unless the mica insulation
between the commutator segments is undercut (lower than surface
of segments) the brushes will not seat firmly against the segments,
RA PO 310341 and the gen erator output will not be normal. Also, there will be
figure 74-Testing Generator Terminal Posts lor Ground to excessive arcing at the brushes. After the commutator has been
Frame End (Tester 4l- T-5575) trued, .the mica must be undercut to a d epth of 0.025 inch. Mica
undercutting is usually done on a machine. If such a machine is not
available it can be d one by hand (fig. 75). Smooth commutator with
2/ 0 flint paper after undercutting.
(I) MAKE GROWLER TEST AFTER U:sDERCUTTJNG MI CA. It is
advisable to repeat the growler tests, paragraph 63 h (1), (b), to see
if a short has developed during turning and undercutting operations.
If a short has developed, it can very likely be corrected by a more
-- COMMUTATOR thorough cleaning between segments and at ends of the commutator.
COMMUTATOR
START ING GROOVE IN MI CA UNDERCUTTING MICA WITH PIECE

65. GENEUATOR ASSEMBLY AND Tf.ST.
WITH 3 CORNERED FILE OF HACK~AW BlADE a. Install Fie ld Coils and Polf' Sh oes. If the field coils have been
MICA SEGMENTS removed from the generator frame (par. 62 h (14)) , care must be
MICA
exercised in their installation to give the correct clearance between
the pole shoes a nd the armature core.
WRONG WAY RIGHT WAY (1) I NSTALL REGULATING COIL. See that groove in generator
MICA MUST NOT BE LEFT MICA MUST BE CUT AWAY
frame is clean and that pole shoe registers in the groove and seats
WITH A THIN EDGE NEXT CLFAN BETWEEN SEGMENTS against the frame. Assemble regulating coil (identified by orange
TO SEGMENTS
paint mark) on pole shoe and locate in upper side of the generator
RA PD 310324
frame with coil leads facing open end of frame. Hold the frame
lightly in a vise and tighten the pole shoe screws. Use a large screw-
figure 75-Methocl of Undercutting Commutator Mica driver with bit ground to fit screw slot perfectly. Unless pole shoe
screws are very tight, and the poles seated firmly against the frame,
d . lnSJ)t'Ct Brush and Spring Assemblies. The main positive the armature core will not have the required 0.007 -inch clearance
and negative brushes are interchangeable. T he regulating brush is between each pole.
thin in section. When brushes have become worn to such ext ent the
(2) INSTALL SHUNT COIL. The shunt fi eld coil is identified by a
long~st side measur~s ¥a inch or less, they should be replaced. At white paint mark and must be assembled in the lower side of the
the t1me a generator 1s completely overhauled, it is advisable to install
a new set of brushes. generator frame. See that coil and pole shoe a re tight against the
119
118
GENERATING SYSTEM
frame to provide armature core clearance of 0.007 inch. Coil leads (d) S witch Terminal Post. The switch terminal post makes con-
must face the open end of the frame. llu t with the shunt coil terminal plate a nd is insulated from the
po!utlve brush holder and th ~ generator frame end by a fiber bushing
b. Install Brush Holders. If the main brush holders have been
removed from the frame end casting, reinstall them as follows :
--
und washer.
(1) NEGATIVE BRUSH HOLDER (fig. 76). The positive and nega- I. •·· Install Armature. Before installing armature, pack the bear-
angs with general purpose grease .
tive brush holders are interchangeable. The installation difference
(1) INSTALL OIL R ETAINING WASHER AND BEARING. Install the
being that the positive brush holder is insulated from the generator
f••lt oil retaining washer in drive end of frame and retain with spri~g
frame end, and the negative brush holder is in contact (grounded)
rang registered in frame bearing housing groove. Install beanng m
with the frame end.
housing.
(2) RELAY TERMINAL P OST, SWITCH TERMINAL POST, POSITIVE (2) INSPECT ARMATURE AND P OLE SHOE CLEARANCE. This inspe_c -
BRUSH HOLDER AND SHUNT FIELD COIL TERMINAL PLATE INSTAL- -· --, tion is not necessary unless o ne or both pole shoes and field coals
LATION (fig. 76). Both the relay and switch generator terminal posts
I J have been removed and reinstalled. Select a piece of paper 0.007 inch
thick (or a double sheet totaling this thickness) by 2:51(; inches wide
SWITCH TERMINAL POST and 6~ inches long. Wrap paper around armature core and i_nsert
RELAY TERMINAL POST armature in the frame. If armature and pole shoe clearance as up
to the 0.007 inch required clearance, the armature can be inserted
INSULATION and will turn freely . If armature does not have required 0.007 inch
' --.
clearance between each pole shoe. pole shoe screws must be tightened.
I, (3) INSTALL GENERATOR FRAME END. The generator frame end

fits over the register in the frame and is located in correct position by
REGULATING a dowel pin. Secure frame end with the two long screws, entering
BRUSH HOLDER from the drive end of the frame. Tighten screws securely. Bring out
POSITIVE field coil leads in correct position for terminal connections, (f) of this
BRUSH HOLDER paragraph.
(4) INSTALL WASHERS ON ARMATURE SHAFT. Install one 0.025
NEGATIVE inch thick spacer washer on shaft, then the bakelite washer, followed
BRUSH HOLDER by two more 0.025 inch thick spacer washers. Four of the 0.025 inch
thick spacer washers may be found on some generators.
GENERATOR END
CASTING CUT AWAY TO
SHOW POSITION AND
INSULATION OF TERMINAL
~
l
!
- (5) INSTALL INNER GREASE RETAINER. Locate the inner grease
retainer on the generator frame end.
(6) INSTALL BEARING ON SHAFT. Press the bearing onto the
POSTS AND IRUSH HOLDERS armature shaft. Locate paper gasket on the inner grease retainer.
RA I'D 310337 Engage the split ring in the bearing housing groove and locate the
-- ..,... 0.020 inch spacing shim next to the split ring. Install the bearing
figure 76-Generator End Section Showing Terminal Post and
Brush Holder Installation I l housing, with spacer and split ring, on the bearing, pressing it tight
against the frame end. Install lock washer and nut on end of arma-
ture shaft and tighten nut.
are utilized to mount the positive brush holder to the generator frame d. Install Rt>gulating Brush Holder. Install the regulating brush
end. Exercise care when assembling these parts to ensure correct con-
holder, the paper gasket, and the outer grease retainer plate and
nections, location, and insulation.
secure with three screws. After the three screws are tightened, the
(a) Relay Terminal Post. The relay terminal post makes contact armature must revolve freely in its bearings.
with the positive brush holder and is insulated from the generator e. Install Drive Gt>ar on Shaft and Check Location of Arma·
frame end by a fiber bushing and washer. lure in Frame. After the drive gear has been installed on the shaft,
(b) Positive Brush Holder. The positive brush holder is insulated the armature can be checked for correct location in the frame to
from the generator frame end by a thick fiber paper insulator. ensure correct position and alinement of the drive gear and oil slinger
within the gear case.
(c) Shunt Field Coil Terminal Plate. The shunt coil terminal
plate is insulated from the positive brush holder by two thin fiber (1) INSTALL OIL DEFLECTOR, SPRING AND DRIVE GEAR. Install
paper insulators. the oil deflector with cupped side over the bearing boss in end of
120 121
GENERATING SYSTEM
generator frame and install the coil spring with large end next to the coil is brought out and connected directly to the negative (main)
deflector. Engage drive gear on splined end of shaft and partially brush holder terminal screw. The lower head of the shunt field coil
engage new retaining pin. NOTE : Do not rivet pin until (2) below is brought out and over the top of the aluminum frame end, directly
has been performed. Rivet pin at both ends. to the switch terminal plate.
(2) CHECK DISTANCE OF OIL SLINGER TO FRAME END. After (b) Regulating Field Coil Leads. The lower lead of the regulating
drive gear and oil slinger have been installed, measure the distance field coil is brought out to pass between the generator frame and
from the outer face of the oil slinger to the end of the generator frame the lower frame end screw and is then wound around the negative
(gasket removed) . Distance should be between 1 :;~~~ 4 inches, and brush wire two times to take up slack, and then connected to the
1:.!%·• inches, and can be adjusted as necessary by removing or adding regulating brush holder terminal. The upper lead of the regulating
a o.ihs-inch thick spacer washer on commutator end of armature. field coil is brought out and is wound around the switch terminal
wire two turns and then connected to the positive brush holder
f. Install Brushes and Conne<>t Field Coil Wire Terminals. All terminal screw.
SWITCH TERMINAL RELAY TERMINAL

POST
SHUNT COIL
GENERATOtt
END CASTING
CUT AWAY TO
SHOW LOCATION
OF FIELD COIL
WIRES AND
TERMINAL CONNECTIONS
SHUNT COIL TERMINAL
REGULATING
COIL TERMINAL
RA P'O 310331
•
I
- SHIFT BRUSH HOL.DER
RA PO 310371
Figure 77-Generator Section Showing Arrangement and Connection
lor Field Coil Leads
Figure 18-Shifting Regulating Brush to Adjust Current
Output ol Generator
brushes must be installed so that the concave ends seat firmly against
the commutator and conform to the curvature of the commutator. g. Test and Regulate Generator. Mount the generator on a con-
The main (positive and negative) brushes and springs are retained ventional test stand so as to drive generator counterclockwise (look-
by clips which are held in place .by the fieM coil terminal screws. The ing at generator drive gear end). Connect positive lead from ammeter
regulating (narrow) brush and spring is retained by the clip soldered to the relay terminal. The other ammeter lead must be connected to
a 6-volt storage battery positive post and the battery negative post
to the end of the brush pig tail. Clip fits into notches in the brush
holder. grounded to the test stand (generator frame) . This connects the gen-
erator to use the regulating field coil only, the same as operating the
(1) SEATING BRUSHES. . If brush faces do not seat fully on the vehicle with the lights off. If the test stand has variable speed drive,
commutator, they should be dressed and faced with 2/ 0 flint paper operate the generator through full range of speeds from lowest to the
until they fit commutator curvature perfectly. highest. Run generator until it becomes quite warm.
(2) CONNECT FIELD COIL TERMINALS (fig. 77). Arrangement of (1) REGULATE AT 2,500 REVOLUTIONS PER MINUTE. With gener-
the field coil leads must be just right so they will clear the armature. ator quite hot, shift the regulating brusn to obtain a four ampere
(a) Shunt Field Coil Leads. The upper lead to the shunt field readini (operatipg on regulating coil only, fig. 78). Connect a jumper
122 123
GENERATING SYSTEM
between the switch t erminal post and frame (ground). This cuts the
shunt field coil into the circuit and increases the current output. At
Il b. Adjustment (fig. 79). T he relay contact points must be cor-
rectly adjusted and the armature must have correct spacing above
the magnet core for sensitiv·~ and correct cut-in and cut-out operation.
2,500 revolutions per minute the current output should be between (1) ARMATURE AND CORE AIR GAP. The space (air gap) between
7 and 7% amperes. the armature and magnet core end is 0.015 inch when the two upper
(a) To Increase Current Output. Shift the regulating brush holder points are in contact. B end upper contact point support and adjust
toward the n egative brush. Minimum distance between the regulating armature to obtain this gap.
brush and negative brush to be not less than Ys-in ch. T ighten the (2) M AIN CONTACT P OINT GAP. After the armature and magnet
three outer grease retainer plate screws after making regulating brush core end air gap have been adjusted, gage the main contact point gap.
adjustment. It should be 0.020 inch and can be obtained by l::iending the lower
(b) To Decrease Current Output. Shift the regulating brush point support up or down as may be necessary.
holder away from the negative brush. T ighten the three regulating (3) SIGNAL P OINT GAP. Press the armature down until the lower
brush clamp screws. main points are in contact and gage the upper contact point gap. It
should be 0.020 inch and can be obtained by bending the upper point
GENEitATOR SIGNAL LIGHT support up or down as necessary.
CONTACT POINT$
- (4) ADJUSTING A RMATURE SPRING T ENSION. The relay main
I
UPPat CONTACT POINT
AIIMATUR£ lower points should close at 6 .3 to 6.8 volts (connect voltmeter to
i
!
AIIMATURE AND
CORE AIR GIU' $UPI'OIIT$PIIING TENSION relay terminal marked "GEN " and t o the relay base), and can be
"DJUSTMI:NT
adjusted by decreasing or increasing the armature spring tension.
...., GENeRATOR·tAnfltY
Increasing the armature spring tension increases the closing voltage,
r,
CIRCUIT POINT$
(0.020 ;•. ) while decreasing the spring tension reduces the closing :voltage. The
LOWER POINT SUPPORT armature spring tension is altered by bending the spring stop,
GEI'<fAATOR mounted on top of the magnet, up or down.
$1GNM LIGHT
·~~~~ TERMINAL
c. Repair. The relay should not be disassembled for attempted
~.,.,,.....,"""~!!!!!!! ;: : ACO ( repair. A relay worn or damaged beyond adjustment service, must
be replaced.
L
• 67. GENERATOR FIELD ~AGNETIC SWITCH.
a. This switch is fitted to late WLA models. F or diagram of
earlier system, refer to TM 9-879. Although this magentic swit ch is
RA PD 310346
put into action only by use of the blackout headlight, it actually
Figure 79-Adiustment Dimensions for Generator Relay Cut-out controls the generator shunt field coil when this headlight is in use;
therefore, it should be considered a part of the generating system.
(2) INSPECT FOR EXCESSIVE ARCING. After the generator has Refer to wiring diagram, figure 65. The generator field magnetic
been run at least 30 minutes, inspect for excessive arcing at the switch is a sealed unit, and if found faulty and/ or damaged it must
brushes. If necessary, re-dress the brushes with 2/ 0 flint paper to - be replaced.
eliminate arcing as much as possible. I l - 68. FITS AND TOLERANCES.
(3) TIGHTEN REGULATING BRUSH H OLDER PLATE. After the
desired current output has been obtained, securely tighten the three a. Table of Fits and Tolerances.
screws which mount the outer grease retainer and clamp the regu- (1) ARMATURE CLEARANCE BETWEEN POLE SHOES. 0.007 inch
lating brush plate. clearance between armature core and each pole shoe.
(2) BRUSH L ENGTH. New brushes are approximately 1~) 6 inch
66. RELAY ADJUSTMENT AND REPAIR. long on the longest side. R eplace when longest side is % inch or less
a. Description. The relay is provided with an additional contact in length.
for the normally open position to control the signal light in the (3) ARMATURE SHAFT BEARING DIAMETER, COMMUTATO~ END.
instrument panel. When the generator voltage exceeds the batte~y Shaft diameter for the small ball bearing is 0.472 inch.
voltage (between 6.3 and 6.8 volts) the relay closes the battery- (4) ARMATURE SHAFT BEARING DIAMETER, DRIVE GEAR END.
generator circuit. At this time, the upper contact points break a nd the
panel green indicator light goes off, indicating that the generator is
charging the battery. This occurs at approximately 20 miles per hour
I Shaft diameter for the large ball bearing is 0.5912 inch.
(5) BEARING FITS. B all bearing inner and outer races are a light
press fit on the armature shaft and in the housings respectively.
I
in high gear. 125
124
SWITCHES AND INSTRUMENT PANEL
CHAPTER 7
HORN AND LIGHTING SYSTEM
Section I
69. DESCRIPTION.
a. The lighting system may be divided into two circuits: the
service light system and the blackout light system (fig. 80). Both
are master controlled by the ignition-light switch and the blackout
headlight is provided with an auxiliary switch. The panel switch has
- - - - - - - - - - .... 10
a lock-out feature, preventing use o f the service lights until a button
has been pressed to release the switch knob for the third, or service
light position. The lighting system is related to the generating system
in that either the ignition-light switch or a magnetic switch (for
blackout headlight) cuts in the shunt field coil to increase the gen-
erator current output with lights on. The service headlight beam is LEGEND
controHed by a toggle switch located on the left handlebar. 1 to 7-SWITCH TERMINALS
8-GENERATOR SIGNAL
LIGHT TERMINAL
70. IGNITION-LIGHT SWITCH. 9-0IL PRESSURE SIGNAL
LIGHT TERMINAL
a. The ignition system, service and blackout lighting systems, 10-SIGNAL LIGHT TERMINAL
ho,·n circuit, panel lights and generator shunt field coil (cuts in with 11 -SPEEDOMETER LIGHT
service lights) are all controlled by the ignition-light switch. 12-BATTERY POSITIVE TER-
MINAL
(1) SWITCHES ON EARLIER MODELS. The ignition-light switch 13-BATTERY NEGATIVE TER-
MINAL
used on earlier models was provided with lock and key. Principle of 16-0IL PRESSURE SIGNAL SWITCH
operation and electrical connection is the same for both nonlocking 17-JUNCTION TERMINAL ION
'----.:'6
and locking types. HORN MOUNTING)
18-FRONT JUNCTION TERMINAL
b. Switch Positions. lUNDER SADDLE!
19-REAR JUNCTION TERMINAL
(1) KNOB STRAIGHT AHEAD IN OFF POSITION. lUNDER SADDLE I
20--STOP LIGHT SWITCH
(2) FIRST POSITION TO RIGHT. Ignition, horn, oil pressure signal 21-BLACKOUT STOP LIGHT
light, generator signal light. 22-BLACKOUT TAIL LIGHTS
23-SERVICE TAIL AND STOP LIGHT
(3) SECOND P OSITION TO RIGHT. Ignition , horn, oil pressure 24-BL.ACKOUT MARKER LIGHT -.:..:
IO:.:.N.:.._-t¥-4.L
signal light, generator signal light, blackout headlight, blackout tail- FRONT MUDGUARD) '
25-SERVICE HEADLIGHT
light, blackout stop light, blackout driving light. 26-IGNITION- LIGHT SWITCH
(4) PRESS LOCKOUT BUTTON FOR THIRD P OSITION TO RIGHT. 27-BLACKOUT HEADLIGHT
28-SPARK COIL I FRONT TER-
Ignition, horn, oil signal light, generator signal light, service head- MINAL SHOWN l
light, service taillight, service stop light, shunt field coil, speedometer 29-HORN ,..-- _
, ...
30-HORN BUTTON I
light. 31-HEADLIGHT TOGGLE
I
c. Disassemble Switch (fig. 82). All switch positions mentioned SWITCH

35-JUNCTION TERMINAL
below apply with switch "upside-down" and in off position.
(1) Remove cotter pin, plain washer, coil spring, and movable
contact plate from end of center p in.
(2) Grasp end of contact bar with pliers and pull and shift side- ItA PO J10J19
ways to release contact bar from retaining notch in the center pin figure, 80-Ughtlng System Wiring Diagram
(fig. 82).
127
126
(3) R emove stationary contact plate (bakelite ring with seven
I l'rminals).
(4) The contact bar t·older assembly can now be removed from
COVER__,~
- I
the switch housing by sliding either one of its bakelite extension Jugs
out of retaining slot in switch housing and then sliding opposite
i ext ension lug out of the other slot.
(S) Remove switch frame and moulded spacer from switch
-
housing.
SPACER
I •
d. lnsp~ct Switch Parts. Inspect all parts, particularly the con-
t act bar and contact plates for excessive wea1' of contact bar and
~·
I
SWITCH
ASSEMBLY I
SWITCH BASE !Frome)
CENTER PIN
:;MALL PLAIN WASHER ----------l~ 0

CONTACT BAR
HOLDER ASSEMBLY - '
! .'
I -.
MOVABLE CONTACT PLATE
-
STATIONARY CONTACT PLATE I -

9 ..
~PLAIN
SPR1NG
WASHER
CONTACT BAR =-·::=e..- COTTER .PIN

RA I'D 310340
Figure 82-Removing Switch Contact 8or

MOVABLE CONTACT PLATE
button or otherwise faulty condition. Contact bar and contact buttons
may be found worn to the extent they no longer make positive con-
tact. Remove any rust on the center pin and thoroughly clean all
parts. Replace any worn or damaged parts.
COIL SPRING ----+-~ e. Assemble Switch. Hold switch housing upside-down, with the
LARGE PLAIN WASHER -+0 lockout button in the tipper, right-hand positiOn, then install parts as
follows (fig. 8!):
( 1) Install the moulded spacer in recess of body with the shoulder
COTTER PIN ----t~ 5 r:» end up.
RA I'D 310215 (2) Install the switch frame so that slot engages the end of the
figure BJ-Ignition-llght Switch, Disassembled lockout buttOn.
128 129
CHAPTER 7
(3) Install the small plain washer on the center pin and pass the
pin up through the spring in the contact bar holder assembly. HORN AND LIGHTfNG SYSTEM (Cont'd)
( 4) Engage the extension lugs of bar holder bakelite plate in the
slots of the switch housing. 1- -, I I
Section II
(5) Install the stationary contact plate in the switch frame with - '
HORN AND LIGHTS
the four terminal lugs away from you.
(6) Locate the contact bar in holder slots and pull center pin 74. HORN.
with pliers to engage contact bar in center pin retaining notch. a. Other than the replacement of cover, cover bolts, terminal
(7) Install movable contact plate so that the two buttons are screws, and adjusting screw, repair cannot be made to horn because
the right-hand side of switch. of construction. If horn does not operate, remove the cover and clean
(8) Install spring, washer, and cotter pin. the contact points; then assemble and adjust by means of screw on
back of horn (fig. 83). NOTE: Unless absolutely necessary, do not
71. MAGNETIC SWITCH. change position of the screw located in center of the diaphragm.
Before attempting horn adjustment, tighten all six bolt nuts.
a. The magnetic switch used to cut-in the generator shunt field
coil when the blackout headlight is turned on is shown in the gen- SPACER DIAPHRAGM
_FRONT COVER
erating system diagram (fig. 80). This switch is sealed and when
found faulty, it must be replaced.
72. STOP LIGHT SWITCH.

j
a. The stop light switch is operated by movement of the foot
service brake. The switch must be replaced when found faulty and/ or
damaged.
73. INSTRUMENT PANEL LAMPS.

a. To replace the instrument panel lamps, the panel cover must
be removed. At the time of lamp replacement, examine contacts and
wiring terminals to ensure perfect electrical and mechanical con-
nections.
CONTACT POINTS
RA PD 310397
.---
1 . Figure 83-Horn Disassembled
•
75. SERVICE HEADLIGHT.

a. If the service headlight body and/ or mounting stud are dam-
aged, replace with a new body. Other components of the headlight
assembly are easily replaced (fig. 84) .. Use prefocused lamp (32-21
CP, 6 V double contact) .
•
76. BLACKOUT HEADLIGHT.
a. The blackout headlight uses a sealed lamp-unit. Lamp housing
is provided with a toggle switch to control blackout headlight sep-
l arately when ignition-light switch is in blackout (second) position.
Any parts badly damaged must be replaced. For correct order of
assembly, refer 4> figure 85.
-
130 131
1.....•••
HORN AND LIGHTS
REFLECTOR AND PACKING LENS DOOR

LA~~p
WIRING ASSEMBLY WASHER I
'\ f r
'i f
MOUNTING Qll . Q-- CONDUIT CLI P
!\
-
,
NUJ ,-:-':)......_
' _-........ I I 1,.-- WASHER GASKET
LOCK
' :)
'J•:··
WASHER '-(WASHE~,/
PLAIN
\ PRE-FOCUSED /
........_NUT
1 - - - WIRE CABLE
GASKET RETA INER
COVER
.r LAMP __...~ COVER SCREW
OUTSIDE
TERMINAL £.<""'; , ~
.:>
DOOR RETAINING SCREW
SCREWS INSIDE TERMINAL SCREWS AND NUTS RA PD 310358
Figure 84-Service Headlight, Disassembled

RA PD 310398
11gure 86-Front Marlcer Light, Dl1011emWed

TOGGLE SWITCH AND LAMP UNIT RETAINER DOOR
LAMP BODY LAMP UNIT
DOOR
SCREWS
GROUND WIRE I 0
~MOUNTING
.. I
WASHER /.., 4¥' 1 -o

TOGGLE SWITCH ()-LOCK WASHER
DOOR RETAINER SCREW
GASKET lf't\_ BODY
~MOUNTING NUT RA PD 310357 SPARE BLACKOUT LAMP UNIT
RA I"D 310359
Figure 85-Biackout Headlight, Disassembled Figure 87 -Service Taillight, Disassembled
77. FRONT MARKER LIGHT.
a. The front marker light mounts on the front mudguard. Use a . (1) SPARE BLACKOUT LIGHT. The lower socket in the left taillight
single contact lamp (3 cp, 6-8 V, single contact). Replace light body ~~ the spare blackout taillight. Simply switch lower plug from right
and parts found in damaged condition. For correct order of assembly s1de taillight to this socket.
see figure 86.
h. Blackout Stoll Light. The top socket in the right taillight is
78. TAILLIGHTS AND STOP LIGHTS. used for the blackout stop light. Lamp is in a unit.
a. Service Taillight (fig. 87). The service taillight is mounted
on the left side of the mounting bracket. The upper socket in light (1) BLACKOUT TAILLIGHT (fig. 88). The lower socket in the
housing is for service taillight and stop. light. The service stop light right taillight serves as the regular blackout taillight. The lamp is
does not operate in daytime when ignition only is on. Lamp is in n in a unit, and is interchangeable with the lamp unit in the lower half
unit. of the left taillight.
132 133
- CHAPTER 8
I
BLACKOUT STOP LAMP UNIT i CLUTCH
DOOR
--- - Section I
I DESCRIPTION AND DATA

DOOR
79. DESCRIPTION.
SCREWS
a. The clutch is of simple multiple dry-disk design with fiber -
.I (J lined plates and steel plates set alternately in the clutch shell. The
disks are compressed by 10 heavy coil springs. One set of disks is
connected with the hub assembly which is secured to the transmis-
sion main shaft gear. The other set of disks is connected to the clutch
BODY shell and sprocket assembly and is driven by the engine chain. The
BLACKOUT LAMP UNIT lA PD 310160 clutch is actuated by a rod which passes through the hollow main-
~
shaft in the transmission. The clutch is controlled by the foot pedal
FlguN 88-llaclcout Taillight, Disassembled ' located on the left footbo ard of the vehicle.
''
80. DATA.
a. Data. R efer to figure 89 with legend for clutch components
and data.
- ·~
I
135
134
A -· .•. .
CHAPTER 8
Ct UTCH (Cont'd)
-
Section II
'
I -
REMOVAL, DISASSEMBLY, CLEANING,
INSPIECTION, AND REPAIR
81. REMOVAL AND DISASSEMBLY.

a. Removal of Clutch from Late Vehicle. Refer to TM 9-879,
then remove clutch hub from transmission gear as follows:
(1) REMOVE CLUTCH HUB NuT (fig.. 90). Remove nut (right-
hand thread) with special wrench (41-W-866-10).
--
1
'
I
~
VI
0 HUB NUT WRENCH
I
1-
lA PD 310345
Figure 90-Removing Clutch Hu& Nut with Wrench (41-W-866-10)
(2) REMOVE CLUTCH HUB FROM TRANSMISSION GEAR (fig. 91).

Use puller (41-P-2905-90) and pull clutch hub from splined trans-
. .
mtssmn gear.
b. Removal of Clutch from Early Models. On 1940 and earlier
WLA models, the clutch hub is a taper fit on the transmission gear.
Use a bammer and a soft punch to remove the hub, ·striking close to
the center but being careful not to strike the bearing.
136 137
REMOVAL, DISASSEMBLY, CLEANING, INSPECTION,
AND REPAIR
82. CLEANING AND INSPECI'ION.
a. Cleaning. Clean all parts thoroughly in dry-cleaning solvent. (6) OuTER RELEASJNr. DISK. This is a built-up assembly form-
ing the compresston and releasing disk. The ten springs compress
b. Inspection. Inspect all parts for good condition. Any ques- 1t against the disks to engage the clutch and the push rod is actuated
tionable parts must be replaced because the clutch is the most im- by the clutch control to "push" it away from the disks (against con:-
portant control in the power line. pression of springs) to release the clut~h. The clutch push rod adjust-
(1) CLUTCH SHELL AND SPROCKET ASSEMBLY. The clutch shell m ent screw and lock nut are engaged with the releasing disk. Worn
(splined ring) and sprocket are of integral construction and wear or damaged releasing disk must be replaced.
and damage to either makes replacement of this unit necessary. (7) CLUTCH SPRINGS. Free length of new clutch spring is approxi-
(2) CLUTCH HUB ASSEMBLY. Inspect studs and pins for good mately 1~ inches. (They may vary plus or minus ¥32 inch.) Old
condition and ball race for wear. If fiber liner is worn or glazed, springs found to be shrunk % inch must be replaced with springs.
replace it. This is the same liner as used on the lined clutch disks.
83. REPAIR.
a. The only repair to the clutch is relining the disks and the clutch
hub. All other badly worn or damaged parts must be replaced to
ensure a perfect, dependable operating clutch.
b. Install New Disk Liners. If new disk and hub liners are in-
stalled, make sure that the rivets are set below the surface of the
'
fiber liner. Do not set rivets with such force to crack or damage the
t • fiber liner.
'
i
- -
t
ASSEMBlY - -
RA PD 31034<4
t
'
Figure 91-Pulling Clutch Hub with Puller (41-P-290.5-90) ''
'
(3) LINED DISKS. Disk liners must be in good condition, not

excessively worn, glazed or loose on the steel disk. New liners can be
installed, or the disk assemblies can be replaced.· Make sure that the
antirattle (ball and spring) devices are in working order to prevent
disk rattle in the spline ways. Note that one disk is lined only on one ~
side and that the disk is sprung, to provide smooth clutch action. The I I
same liner is used in all lined positions in the clutch.
( 4) STEEL DISKS. If the steel disks are worn, cut or burned,
replace them.
(5) INSPECT BALL RACES. Inspect the inner and outer ball races,
balls and ball retainer for good condition. Replace worn parts. -
138 139
ASSEMBLY, INSTALLATION, AND ADJUSTMENT
CHAPTER 8
CLUTCH (Cont'd)
Section Ill
ASSEMBLY, INSTALLATION, AND ADJUSTMENT
.
I ..... ,., ,....,. •
I OUTER DISK
84. ASSEMBLY AND INSTALLATION. ASSEMBLY ADJUSTING SCREW
~. The clutch cannot be completely assembled until the clutch
hub and sprocket assembly is installed on the splined end of the
transmission clutch gear . R efer to figure 89 for correct order of
\ -'7SPRINGS LOCATED
OVER HOLES IN DISK
assembly.
b. Install Clutch Hub on Transmission Clutch Gear. Engage
the hub and gear shaft splines and drift the hub onto the splines with
a block of wood and a hammer. Install the lock washer and nut and
tibhten nut (fig. 90) securely with wrench (41-W-866- 10). Lock the
nut by setting the washer in one of the nut slots with a punch .. / ~
ADJUSTING SCREW NUT
c. Ball Bearing, Bearing Retainer Plate and Retainer Plate
lA PD 310362
Lock Rings. Install the ball bearing retainer (with sixty ;,:1:rinch
balls) on the clutch hub race; then install the bearing retainer plate
on the studs with the shoulder edge inward (toward the ball retainer). Figure 92-Springs Assembled on Releasing Disk
The retainer plate is held in place by three steel rings, slipped over
three of the short studs. CAUTION: II the three long studs have
grooves, do not engage the rings in the grooves. LARGE ASSEMBLING WASHER
-
ADJUSTING
d. Install Clutch Huh on Transmission c.lut('h Gear. Apply a I
SCREW NUT
light coat of grease to ball bearing before installing the hub shell.
: SPRING
j
With the clutch hub in place on the ball bearing, the disks can be /COMPRESSION
installed in the shell and sprocket assembly. COLLAR
e. Install Disks (refer t o TM 9 -879). It will be noted that the
two steel disks are stamped "OUT" on one side. These sides must SPRINGS
face outward when installed in the shell. The two steel disks are also
provided with ~ntirattle (ball and spring) devices to prevent disk
noise when engaged with the spline keys within the shell. Correct
order of disk assembly is as follows: '
OUTER DISK
ASSEMBLY
(1) Lined disk fitted correctly on the hub studs.
(2) Steel disk fitted to shell spline keys with side stamped ''OUT"
fa cing outward. CLUTCH HUB
(3) Lined disk fitted correctly on the hub studs. ASSEMBLY
( 4) Steel disk fitted to sh ell spline keys with antirattle device
staggered in position from a ntirattle device on the first steel disk RA PD 310363
installed. Side stamped " OUT" facing outward. Figure 93-Aiining Springs, Dislc and Collar on Clutch Hub Studs
(5) Spring disk (lined on one side) is installed on the hub studs
with the lined side inward, facing the steel disk. the collar "dimples" in ends of 7 of the springs. Place a large washer
f. Assemble and Install Releasing Disk, Springs and Spring (1~ i~. d~a x Y8 in. thick with a Ys in. center hole) over the push
Collar (figs. 92 and 93). Place the 10 springs upright on the releastng rod adjusting screw; turn on the adjusting screw lock nut and com-
disk to centrally locate each of the 10 stud holes in the disk. Place press tbe springs lightly. Turn assembly over and observe alinement
the spring collar (flanged edge down) over ends of springs, locating of springs and disk holes. If necessary, insert a ¥a-inch rod throu1h
140 141
CHAPTER 8
holes to aline the springs. Tighten down the adjusting screw nut. The CLUTCH (Cont'd)
assembly is now ready for complete clutch assembly.
Sedion IV
(1) INSTALL RELEASING DISK ASSEMBLY. It will be noted that
the three long, threaded-end, clutch hub studs are not spaced FITS AND TOLERANCES
equidistant with relation to each other. It will also be noted that the
three stud holes in the spring collar are not spaced equidistant with 86. FITS AND TOLERANCES.
relation to each other. Therefore, when installing the releasing disk /
and spring assembly on the clutch hub studs, the three threaded a. Hub and Shell Ball Bearing. Free running on sixty %2 -inch
studs and the holes in the spring collar must be alined. Install steel balls.
assembly on studs, install the three nut locks and the three adjusting b. Lined Disks. Replace lining (or disk assembly) when liners
- are worn to rivet heads.
t c. Spring Length. Free length of new clutch spring is approxi-
mately l ~ inches. Replace spring when shrunk Ya inch.
d. Compression Collar to Disk Measurement. The distance
-
I
between shoulder of the spring collar and face of the releasing disk
I• should be 1% 2 inches, and never less than Ys inch to ensure equal and
correct tensioning of the 10 springs (fig. 94).
e. Clutch Hub on Gear Shaft Spline. Light press fit between the
clutch hub and transmission clutch gear shaft spline.
RA PD 310224
figure 94-Measuring Distance Between Spring Collar ancl Disk

lor Initial Acliustmenr
nuts. Tighten all three adjusting nuts evenly until the distance
between shoulder of the spring collar and face of the releasing disk
is 1% 2 inches (fig. 94). Bend up nut locks to retain adjusting nuts
(a) Remove the Large Washer from Push Rod Adjusting Screw.
The large washer (used for assembling purposes only) must be re-
moved from the push rod adjusting screw and the adjusting screw
lock nut reinstalled on the screw.
85. ADJUSTMENT.
a. Adjustment of the clutch push rod is made after transmission
and clutch assembly has been installed in the vehicle because the
action of the clutch operating cable, clutch release lever and push
rod is closely related. For instructions covering clutch control adjust. •
ment in vehicle, refer to TM 9-879. 14 3
142
CHAPTER 9
CHAPTER 9 TRANSMISSION (Cont'd)
TRANSMISSION Section II
Section I DISASSEMBLY, CLEANING, INSPECTION, AND REPAIR

DESCRIPTION AND DATA 88. DISASSE"BLY.
a. f.lf'an Housing. Before disassembling the transmission, clean
87. DESCRIPTION AND DATA. exterior to remove caked dirt, grease, and grit.
a. Description. Transmission is of constant-mesh, progressive b. \fount Transmission. Secure transmission in a copper- jawed
type .. Gears are always in mesh and when shifting from low to high - vise by clamping the mounting studs. Proceed with disassembly as
or VICe versa, it is necessary to shift through neutral and second I' follows:
positions. Transmission is of three-speed design and on WLA models
• • ( 1) REMOVE CLUTCH. If clutch is assembled on transmission,
re':'erse gear 1s not provided. Sliding shifter clutches, actuated by the
~h1fter drum cam, engage with dogs in the clutch gear and recesses -
remove according to instructions in paragraph 81.
m the second and low gears depenc;Jing on the gear selected. Use of ' (2) REMOVE STARTER CRANK. R emove the starter crank clamp
needle: rollers, close fitting bronze bushings, and close tolerances t bolt nut a nd bolt and pull starter crank off of squared end of
necessitates use of engine oil for lubrication. · countershaft.
b. Data (fig. 95). (3) REMOVE SPROCKET COVER AND CLUTCH RELEASE LEVER
Gear ratios: ASSEMBLY (fig. 96). Remove the four stud nuts which secure the
H'1gh gear . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . 1 to 1 sprocket cover to the transmission case. It may be necessary to pry
or drift cover off of the studs.
Low gear reduction . . . . . . . . . . . . . . . . . . . 2.47 to 1 --
Second gear reduction . . . ... ... ...... _ 1.57 to 1 • (4) REMOVE COUNTERSHAFT SPROCKET (fig. 96). Bend down nut
Oil capacity .. . . ... ......... . .. . ... . ... ___ . _~ pint
I lock and remove nut. It will be necessary to strike wrench with a
hammer to loosen nut. Remove the sprocket from shaft taper by
giving it a light but sharp rap with a hammer, near outer edge, being
careful not to strike and damage the sprocket teeth.
(5) REMOVE CLUTCH PUSH Roo ASSEMBLY. The clutch push rod
and bearing assembly can now be withdrawn from the mainshaft.
-
(6) REMQVE TRANSMISSION CASE ToP CovER. Remove the 10
' screws and lock washers which secure the case top inspection cover.
I Drain oil from case.
(7) REMOVE SHIFTER CAM (fig. 96). Remove the lock screw and
pull the shifter camshaft out of transmission case by using a forked
pry tool in the shaft slot. The shaft may be quite tight in the case,
and if the head should break off in removal, it will be necessary to
drill a hole in the case (at shaft opposite end) and drift the shaft out.
Partly engage high gear so that notch in right end of shifter cam
clears boss in side of case for removal.
(8) REMOVE SHIFTER FORK ASSEMBLIES (fig. 96). Drift the
shifter fork shaft out through the hole in the transmission side cover.
(9) REMOVE TRANSMISSION CASE SIDE CovER (fig. 97). Remove
the five screws and· two stud nuts which secure side cover to case.
Free the cover from case by tapping around edge. At the time cover
is removed, the mainshaft needle rollers (21 in number) will prob-
ably fall out of position. Keep needle rollers in a container and
identify them. With the cover removed, gears, shafts, and bearings
can now be removed from open side of case.
144 ' 145
..
' ... ;,..: ~ ·-
5
~
@I ~
0 ~
o fl/#4
G
~
.
'-"""-- 0
E ~ K 0 ~
hwfl~ J i l
0 ~
~~
J~
lle/~~fk.J.
c l ,J -: M N
~@ ~
\ 0 p
A
lE
lE, IT
..
~
Al~
~
g;;:. A~K ll{,b_

u
1
II]
~~w
Oo ~
~ / _. _._
I :;z' lll
o ~l~ '~ ~
A~
'~
14M
~
oleo
I
lA f ~ AX
AY \
AS AR ' AP
AQ
AJ AH-Q>
.
AE~~~ "J~ ~
Q 4l \ ' y
AZ AG-~
AF-lfi
..~ I
AC
lA PD 310336
figure 95- fnJrtllftiuion, Disar.sembled
A -SIDECOVER SCREWS (51
1 -SIDECOVER ASSEMBLY
$ -COVER SCREWS AND WAS HERS
( 11 EACH)
T-CAMSHAFT lOCK SCREW

AM -THRUST BALLS AND RETAINER
AN - THRUST BEARING RACE ->
0
U'
AO -CLUTCH GEAR Cll

C -GASKET Cll
AP MAINSHAFT ENOPLAV SPACER rOO
D -COVER NUTS
U-SHIFTER CAM SHAFT
15/16 IN. x 0.078 TO 0.113 IN. THICK) i
V-CAM SHAFT RUBBER Oil SEAL
•...-<
£ -COVER RUBBER OIL SEAL
W - SHIFTER LEVER AND SHAFT
AQ -SHIFTER CLUTC H -
SECOND AN D HIGH .
F - ROllER END WASHER
(OD. 1 IN. x 0.180 IN . TH ICK) (2 ) X -S HIFTER SHAFT LEATHER WASHER AR -SEC ONO GEAR ...n
G -RIGHT SIDE BEAR ING ROllER Y -SHIFTER SHAFT SPRING AS -LOW AND SECOND GEA R END PLAY
"'
>
z
(31.. IN. x 0.) 14 IN.) (24)
WASHER 100 1-7/16 IN. x 0.040 TO
-
.....
%-S HIFTER GEAR 0075 IN l
H -COUNTERSHAFT GEAR
z
AA-SHIFTER GEAR RETA INING SPRING AT - LOW GE AR
..
Q
~
J - ROllER END WASHER
(OD, 1-5/ 64 IN. x 0.092 IN. THICK)
AI - SHIFTER FORK ASSEMBLY-
SECOND AND HIGH
AU - LOW GEAR END THRUST WASH ER
(OD 1-7 / 32 IN. x 0.052 IN. THICK)
-z
Cll
. BEARING .ROllER
K- LEFT SIDE AC - SHIFTER FINGER ROllER AV -SHIFTER CLUTCH · LOW GEAR 'a
mo IN. x 0.152 IN.) ( 19)
"'
AD - SH IFTER FORK ASSEMBLY-LOW
!l
L - GE>!.R tND WASHER
(OD, 1-3/16 IN. x 0.080 IN. THICK)
AE - SHIFTER CAM
AW - MAINSHAFT
AX -THRUST WASHER -0
M -COUNTERSHAFT
AF - SHIFTER CAM PLUNGER SCREW
(OD 1·7164 IN. x 0.052 IN THICK)
A Y -SPACING COLLAR
.z
AG - SH IFTER CAM PLU NGER SPRING >
N - STARTER CLUTC H
AH - SHI FTER CAM PLUNGER BAll
AZ - MAINSHAFT ROLLERS z0
(5a IN. x 0.152 IN.) (21 )
0 -STARTE R ClUTC H SPRING
AJ - SH IFTER FORK SHAFT ;IIJ
BA -ROLLER END WASHER
P-COUNTE RSHAFT END SPRING
AK- ROLLER END WASHER (00 1-3/ 16 IN . x 0.063 IN. THICK) "'
'a
9 -GEARCA SE COVER
R-GASKET
AL- CLUTCH GEAR BEARI NG ROLLER
(0.615 IN. x 0.125 IN.) (40)
lA PD 3103l6B
-
>
;IIJ
Legend lor figure 95-Transmission, Disossembled

DISASSEMBLY, CLEANING, INSPECTION, AND REPAIR
(10) REMOVE MAINSHAFT, GEARS, ETC. Withdraw the mainshaft,
with gears, spacers, shifter cams, etc., from the transmission case.
The clutch gear will probably stay in position due to friction of the
oil seal. Remove the clutch gear, thrust race, thrust ball bearing and
the needle rollers. Keep needle rollers in a container and identify
location. Remove the lock ring, push rod guide, seal, washer, spring,
SPROCKET COVER AND

CLUTCH LEVER ASSEMBLY
END COVER
I .
\"'''"'): '''")'":' i'>"':l'"\'>~>
A REMOVING SPROCKET COVER AND B REMOVING SPROCKET FROM MAINSHAF~ ROL~ERS I

CLUTCH LEVER ASSEMBLY MAINSHAFT TAPER RA PO 310311
Figure 97-Gear Ccue End Cover Removed
"T'"' CAM SHAFT
IFTER CAM
-
CLUTCH GEAR
1 LOCK RING
' STEEL GUIDE
RUBBER SEAL PUSH ROD
STEEL WASHER
....~"'\
•
\,)
RA PO 3103*0
l
I
'
SPRING t
RETAINING CUP
\
c REMOVING GEAR SHIFTER CAM D REMOVE: SHIFtER FORK' SHAFT RUBBER SEAL
SHAFT BY PRY METHOD BY DRIFTING FROM CASE
ItA PO 310364
Figure 96-Disassembling Transmission
Figure 98-Ciutch Gear and Push Rod Oil Seal, Disassembled
spring cup disk, and small seal from the spline end of the clutch
gear (fig. 98). ( 13) CLUTCH GEAR SHAFT OIL SEAL. Inspect the oil seal pressed
(11) REMOVE COUNTERSHAFT, GEAR, BEARINGS, 8TAR1F~ into the outer side of the clutch gear shaft roller race for worn and/ or
CLUTCH, ETC. Withdraw the countershaft assembly, taking cart' no 1 damaged condition. If seal is in good condition, do not remove it. If
to lose starter clutch springs. R emove gear from shaft and kt t P seal appears in bad condition, remove by drifting it out from inside
needle rollers in container to identify location. of case. The left side roller bearing retaining washer is located back
(12) REMOVE SHIFTER CAM PLUNGER, BALL AND SPRING. Rc: of oil seal, next to the outer race. It is not ne<:essary to further dis-
move the cam plunger cap screw, spring and ball. assemble the transmission case until it has been cleaned and inspected .
148 -~ - 149
-- .j ; -
of the starter stroke. Examine the heads of the two starter clutch
89. CLEANING AND INSPECTION. tripper bolts for excessive wear at points where cams contact the
a. Cleaning. Clean all parts in dry-cleaning solvent and dry bolt heads. Replace tripper bolts if heads are excessively worn
with air. Thoroughly clean case, removing all traces of oil and dirt and/ or damaged.
deposits. (2) CASE SIDE COVER. When the case side cover countershaft
b. Inspection. Inspe~t all parts to determine which must be bronze bushing and the mainshaft needle bearing outer race are
replaced. If any roller bearing inner or outer race is found with badly worn and/ or damaged, the bushings must be replaced. The
damaged or pitted surface, perceptible wear shoulder is found at countershaft bronze bushing hole standard size is 0.775 inch and the
side!: of roller path, or measurements shows more than 0.010 inch needle roller race 1.1 79 inches. Replace bronze bushing if excessively
wear, part affected should be replaced and bearing refitted with new worn. Oversize needle rollers are available to take up normal wear
rollers of required size for correct clearance. between the mainshaft and roller race.
(3) SHIFTER CLUTCHES AND GEARS. Inspect all gears for worn,
pitted or damaged teeth. Give especially close attention to chipped,
rounded, or battered corners of engaging dogs on shifter clutches and
clutch gear and engaging slots in other gears. Damaged engaging
dogs and slots will cause transmission to creep out of engagement
'i under steady driving load. All gears and shifter clutches with dam-
aged (badly rounded) engaging dogs and slots must be replaced.
(4) GEAR BuSH INGS. Installing and reaming gear bushings calls
for extreme care to ensure correct sizing and alinement.
(a) Clutch Gear. Standard hole size for the bronze bushing in
the clutch gear is Y4 inch. Clearance between shaft and bushing is
0.002 inch.
(b) Low Gear and Second Gear. Standard hole size in low gear
and second gear bushings is 1 ~) 6 inch. Clearance between shaft and
gear bushings is 0.001 inch.
•
'
·(5) MAINSHAFT. Inspect mainshaft for good condition of sprocket
SHIFTER GEAR SHIFTER LEVER nut threads, keyways and wear at needle bearing, low and second
gear and clutch gear points. Shaft with bearing diameters worn more
than 0.001 inch must be replaced.
(6) COUNTERSHAFT. Inspect countershaft for good condition
generally and wear at needle bearing and shaft end bearing points.
(1) INSPECT CASE. Inspect for cracks or breakage. See that Shaft with bearing diameters worn more than 0.001 inch must be
mounting studs are in good condition and are tight in case. replaced.
(a) Secqnd Gear Retaining Bracket (fig. 99). The second gear I (7) StARTER CLUTCH AND CouNTERSHAFT GEAR. Inspect the
I
retaining bracket locates the second gear on the mainshaft. Inspect teeth on starter clutch and engaging teeth in end of countershaft gear
for wear caused by contact with side of the second gear. Replace if for good condition. Either gear or clutch with chipped, badly worn or
badly worn where face contacts side of the second gear. broken teeth must be replaced.
I.
(b) Clutch Gear Outer Roller Race. Inside diameter 1.722 inches. (8) MAINSHAFT THRUST BEARING AND RACE. Inspect the thrust
' I
Inner face of race is for thrust ball bearing. Inspect races for signs bearing race for pits, roughness or noticeably worn condition. Inspect
of wear. Oversize needle rollers (0.0004-in. and 0.0008-in. oversizes the retainer and balls for good condition. Replace both bearing and
only) are available to take up normal wear of race. Excessively worn '
i
=-= race if found in bad condition.
or damaged race must be replaced. '
' (9) SHIFTER CAM AND SHAFT. Inspect shifter cam for wear con-
(c) Countershaft End Bushing. Bushing is pressed into a cup and dition. The cam gear teeth must not be excessively worn or broken.
cup is pressed into case. Normal hole diameter of bushing is 0.611 Cam bearing and shaft clearance is 0.001 inch. Standard shaft
inch. Replace when countershaft end and bushing clearance exceeds diameter is 0.374 inch.
0.003 inch. (10) SHIFTER GEAR AND SHAFT. Inspect shifter gear for condi-
(d) Starter Clutch Tripper Bolts. The tripper bolt heads are used tion of teeth. When found excessively worn or broken, replace the
to disengage the starter clutch from the countershaft gear at the end 151
150
gear. The shifter gear shaft standard diameter is 0.561 inch for the the low, second or clutch gear is good enough for satisfactory further
large size and 0.374 inch for the small (end) size. service, then replace bushings. Usually the shifter dogs or engaging
(11) SHIFTER FORK ASSEMBLIES. Note that shifter forks are slots are so rounded and tiam3ged as to make further use of the part
impractical.
assembled on the bushings for right and left positions on the shaft.
If assemblies are taken apart, pay attention to location of all parts, (2) TRANSMISSION CASE BusHINGS. The bronze countershaft
especially the thin spacing washers between the shifter finger and bushing in the transmission case can be replaced when clearances
shifter fork. exceed wear limits. (Owing to the fact that the starter is used very
(a) Shifter Fork Shaft. Shaft is 0.3745~inch diameter. little, the starter shaft bronze bushings in the case and case side cover
seldom need replacement.) The clutch gear outer roller race can be
(b) Shifter Fork Bushin~. Standard hole size in bushing is ¥s pressed out after the case is warmed (not to exceed 300° F). NOTE:
inch. Case must a/so be warmed before pressing in new roller race.
(c) Shifter Finger and Finger Roller. The finger roller rides (3) CLUTCH GEAR SHAFT OIL SEAL. If the oil seal is replaced,
'
within the cam~ways of the shifter drum with a normal clearance of !. install the roller bearing retaining washer in the outer race: then
press oil seal squarely into race with lipped side facing inward. The
CLUTCH OPERATING LEVER SPROCKET COVER
tensioning spring is visible from the lipped side of the seal.
( 4) TRANSMISSION CASE SIDE COVER. The starter shaft bronze
bearing seldom needs replacement. However, if wear limits show
replacement is necessary, replace bushing, making sure that the flat
side is in correct location to provide sprocket tooth clearance. If the
outer roller race must be replaced, use arbor press and make sure
new race is started and pressed squarely into the case side cover hole.
(5) SPROCKET COVER AND CLUTCH LEVER ASSEMBLY. If either
[
sprocket cover or clutch lever are broken or damaged, replace parts.
Figure 100 shows correct order of clutch lever assembly. .
I
b. R6placing Oil Seal in Assembled Transmission. Use com~
bination tool (41~R~2389-47). The clutch gear shaft oil seal can be
-
replaced in assembled transmission either in or out of vehicle. Illus~
! '
trations in figure 101 show oil seal replacement with transmission in
~·.,__ SPRING WASHER l
vehicle.
LOCKS-___;_ _,P~
SCREWS----- -;\l!J"
(1) REMOVE CLUTCH AND CLUTCH HUB. To remove clutch and
clutch hub from transmission clutch gear, refer to paragraph 81.
RA PO 310379
(2) REMOVE OIL SEAL. Refer to illustrations in figure. 101, and
figure 100-Sproclcet Cover ond Clutch Lever, Disassembled applying the following removal steps:
-
I (a) Screw the pilot stud onto the clutch gear until it bottoms
0.005 inch. Roller size is 0.370 inch, and hole size is 0.289 inch. The I against the end of the gear as shown in B, figure 101.
I
finger stud size is 0.287 inch. (b) Slide the puller body over the guide stud (with T -handle
(d) Shifter Fork. Shifter fork width is 0.121 inch. pusher and puller screw removed) with the body stop (extended arm)
(e) Gear Shifter Drum and Shaft. The gear shifter drum shaft in downward position. Turn the body clockwise until the body stop
is 0.374-inch diameter. The cam-ways (finger roller slots) in the gear bears against either the inner chain guard or the gear box, as shown
shifter drum are ¥s inch wide. The gear shifter drum shaft holes are in C, figure 101.
Ys~inch diameter. (c) Insert punch (refer to fig. 101) through each of the three
holes in the puller body and punch-mark the oil seal for drilling .
•
90. REPAIR. (d) Remove the puller body and pilot stud and drill a 3~l 2 -inch
a. Welding of broken transmission cases can be done providing hole through the outer face of the oil seal, at each punch-mark.
the finishing does not call for machine operations or special alinement (e) Again assemble pilot stud and puller body on the clutch gear.
fixtures not available. All other repairs must be made by replacement Screw the three self-tapping screws into the holes drilled in the oil
of worn or damaged parts. seal (through holes in puller body). Make sure all three screws are
(1) REPLACING GEAR BUSHINGS. If general condition of either tight so that puller body is tight against oil seal.
-
152 j
. 153
(I) Screw the T -handle puller and pusher screw (turn to right)
PILOT STUD T-HAN DL( PUSHER
into the puller body until the oil seal is withdrawn, free from the
NUT AND PULLER 1 bearing race. Refer to D , figure 101.
t l
I
( 8) Remove tool from clutch gear shaft. Also remove the three
R BODY self-tapping screws and discard the old oil seal.
PILOT STUD (3) INSTALL NEW OIL SEAL (fig. 101). B efore installing a new oil
/ • seal, remove all burs and nicks at the outer edge of the oil seal recess
"~~
and in bearing race, then proceed with installation as follows:
t'
No. 10 x 15/a IN .IPUNCH
(a) Apply a little oil or grease to inner composition surface of oil
seal, to prevent turning member from burning and dama~ing new oil
seal when transmission first goes back into service. (Note that one
SELF-TAPPING SCREW S end of oil seal guide sleeve has a slight counterbore and the other
• OIL SEAL GUIDE SLEEVE PILOT end is flanged .) Insert co unterbored end of sleeve through closed side
A-TOOL NOMENCLATURE 8-PILOT STUD SCREWED of oil seal and place guide sleeve and seal onto gear. Correctly
t)P..ITO CLUTCH GEAR assembled, spring tension side of seal will be inward, toward trans-
mission. Refer to E, figure 101.
(b) Again screw the pilot stud onto the clutch gear, until stud
· T-HANDLE PULLER
bottoms against end of gear as shown in F, figure 101.
(c) Place the puller body over the guide stud and push the oil
SCREW
AND P US~~ER
I .
-
seal inward against gear box.
(d) Screw the T-handle puller and pusher screw into the puller
body as far as possible without moving the puller body away from
I the oil seal.
'
I . (e) Place the pilot stud nut on the threaded end of the pilot stud
and turrt nut on tight. Assembly will then appear as shown in F,
figure 101.
(f) Unscrew the body handle to press in the oil seal (F, fig. 101).
NOTE: The pilot stud has a screwdriver slot in outer end to tishten
C-PUNCH MARKING
or hold the stud if it loosens while unscrewins T-handle to press in
D-TOOL ASSEMBLED, TURN oil seal. Make sure the new oil seal is bottomed in its recess. Do not
OIL SEAL FOR DRILLING CLOCKWISE TO PULL SEAL
apply further heavy pressure after seal bottoms, as doing so may
damage the seal.
( 8) Remove oil seal tool from clutch gear.
(h) Stake the oil seal bushing lightly, with a blunt chisel or
punch at three equidistant points to prevent the oil seal from turning
or working out of its recess.
.'
OIL SEAL GUIDE SLEEVE

ON CLUTCH GEAR :::Iii"*" RA PD 31 0,. I
E-OIL SEAL IN POSITION F-TOOL ASSEMBLED, TURN
FOR INSTALLATION COUNTERCLOCKWISE TO
INSTALL OIL SEAL
figure JOJ-Jlemoving Clutch Gear Oil Seal with Tool (41-Jr-2389-41)

154 155
ASSEMBLY
--
(2) MAINSHAFT AND CASE SIDE COVER ROLLERS. Standard size,

CHAPTER 9 1 0.152 inch ~ % inch available to 0.001 inch oversize in steps of 0.0002
inch. Twenty-one rollers useJ in the bearing.
TRANSMISSION (Cont'd) (3) COUNTERSHAFT GEAR LEFT END ROLLERS. Same as (2)
above, except that only 19 rollers are used in this bearing.
Sedion Ill (4) CouNTERSHAFT GEAR RIGHT END RoLLERs. Standard size
ASSEMBLY -
0.114 inch x ~ inch available in 0.0004 to 0.0008 inch oversizes only.
! Twenty-four rollers used in the bearing.
91. ASSEMBLY. l (5) INSTALL COUNTERSHAFT GEAR AND STARTER CLUTCH
a. General. Assembly of the transmission calls for correct clear- ASSEMBLY (fig. 102). Refer to figure 95 for correct order of assembly
ance fitting of the needle rollers; correct adjustment of the mainshaft for countershaft gear and starter clutch assembly (items E to P
end play; correct end play of low and second gears; correct adjust- inclusive).
ment of the shifter clutches and correct timing between the shifter
lever gear and gear shifter drum gear. Reference to the disassembled THRUST WASHER MUST
parts in figure 95 will assist in the correct assembly of parts. BE _IN PLACE
\
I
•
'
I
I
, I
~
"': ....
~
.........
_ ....- - "..............__ ~
....... , $$ .........
COUNTERSHAFT
RA P'D 310313
Figure J03 -Installing Mainshaft and Gear Assembly in Clutch Gear
•
lA PO 110SI2
c. lnstaH Clutch Gear (fig. 102). Insta ll the roller bearing end
washer in the outer race. Secure the selected roller to the outer race
Figure J02-Countershaft Assembly and Clutch Gear Installed with grease. Insert oil seal guide (41-G- 1255) through the oil seal
from ~h~ o_utside so that it will be in place to meet the clutch gear
b. Fitting Needle Roller Bearings. All needle roller bearings when 1t ts mserted through the bearing from the inside. Assemble the
must be fitted to give from 0.0006 to 0.001 inch (0.0008 in. preferred) ball thrust bearing race and ball and retainer assembly on the clutch
bearing clearance. The needle rollers are not assembled in retainers gear. Insert the clutch gear through the bearing from the inside. of the
and must, therefore, be held in the outer bearing races with a light case, making sure that the gear end is engaged with the oil seal tool
application of grease for easy assembly. ! .... . before pushing the gear shaft through the oil seal.
(1) CLUTCH GEAR NEEDLE ROLLERS. Standard size, 0.125 inch X l d. Adjust the Mainshaft End Play (figs. 103 and 104). The main-
0.615 inch available in 0.0004 inch and 0.0008 inch oversizes only. shaft end play adjusting spacer washer (item AP, fig. 95) is avail-
Forty rollers used in the bearing.
157
156
t i
ASSEMBLY
able in thicknesses 0.078 to 0.113 inch, in steps of 0.005 inch to obtain 'It l'<lnd gear bracket and case cover i:>.:aring race. This end play is
mainshaft end play of 0.003 to 0.005 inch. ohtumed by selecting a low and second gear end play adjusting washer
(1) Assemble spacer washer on mainshaft (do not assemble (1tem AS, fig. 95) of correct thickness to fit between the low and
gears or clutches on shaft) and insert shaft end in the clutch gear 1econd gears on the mainshaft. Adjusting washer is available in
bushing. Install thrust washer and spacing collar (items AX and AY, thicknesses of 0.040 to 0.07 5 inch, ·n steps of 0.005 inch. Adjust low
fig. 95), on the other end of the mainshaft. und second gear end play as follow;;:
(2) Install the roller bearing end washer in the case side cover (1) Assemble only the low gear end thrust washer, low gear end
race and retain the selected rollers to the outer race with a light play adjusting washer and second gear on the left end of the main-
coat of grease. Assemble the case side cover and gasket to the case
and securely tighten with the five cover screws and the two stud nuts. THICKNESS GAGE
NOTE : Case cover screws and stud nuts must be as ti~ht as in final DETERMINES
assembly; otherwise the end play in final assembly will be incorrect. END PLAY OF
MAINSHAFT
TH~UST WASHER AS- SPACER WASHER BETWEEN
SEMBlED ON MAIN· MAINSHAn SHOULDER AND
SHAn BETWEEN LOW END OF CLUTCH GEAR
AND SECOND GEARS DETERMINES MAIN-
DE'TERMINES END PLAY SHAn END PlAY
OF THESE GEARS (0.003 IN. TO 0.00, IN.)
BETWEEN RETAINING
BRACKET AND GEAR
BO~ SIDE COVl'R.
ADJUST END PLAY TO
0.00, IN. TO 0.007 IN
WITH WASHER OF
REQUIRED THICKNESS.
END PLAY GAGE

ON MAINSHAFT
SECOND GEAR RETAINING BRACKET
U. I'D 310370 •
RA PD 310365
figure 104-Points to Checlc fol" Mainshaft End Play Adjustment
figure 105-Checlcing Mainshaft End Play with Thickness Gage and
fnd Play Gage (41-G-198)
(3) Check the end play of the mainshaft with special end play
gage (41-G-198) and thickness gage (fig. 105). If end play does not
come within the 0.003 to 0.005 inch limits, remove mainshaft and shaft. On the right end of the mainshaft, assemble the thrust washer
install a spacer washer selected to give the correct end play. and spacing collar.
(4) After the correct mainshaft end play adjustment has been (2) Install rollers in the side cover race, retaining with a light
established, remove mainshaft from case· and set aside the spacer coat of grease. Install cover and gasket on the case and securely
washer selected, to be sure that it goes into the final assembly. tighten the five cover screws and the two stud nuts. Tighten the cover
e. Adjust End Play of Low and Second Gears Between the screws just as tight as in final assembly.
Retaining Bracket and Case Side Cover (fig. 106). The second gear (3) Check end play of low and second gears between the side
retaining bracket is mounted in the transmission case to locate and cover and the second gear retaining bracket with a thickness gage.
retain the low and second gears on the mainshaft. The low and second NOTE: Insert ~a~e blade between the face of the second ~ear and the
gears must have 0.005 to 0.007 inch end play between the face of the bracket. End play must be between 0.005 and 0.007 inch.
158 159
- __, ASSEMBLY
(4) Select adjusting washer of proper thickness to give required driving dogs of the shifter clutch and the clutch gear and the shifter
I . fork and the low gear. These distances are determined after the
end play.
(5) After correct end play adjustment has been attained, remove shifter cam is in place.
the mainshaft assembly from transmission case and make sure that (l) INSTALL SHIFTER FORK ASSEMBLIES (fig. 107). Pass the
selected end play washer remains with the assembly. Reinstall the shifter shaft through hole in right side of case and through holes in
copntershaft, starter clutch, bearings, and countershaft gear with all the shifter fork bushings. The forks must be engaged with the grooves
parts in correct order of assembly. Reinstall the mainshaft assembly in the shifter clutches.
with all parts in correct order, and with the two selected end play (2) INSTALL SHIFTER LEVER AND GEAR. The spring fits between
adjusting washers in place. If new shifter clutches are installed see the hub side of the large shifter gear and the case bushing. The
that they slide freely on the shaft splines without binding. leather washer fits between shifter lever and outside of case. Install
- the gear on the shaft square with the lever in a vertical position and
CLEARANCE BETWEEN
SHIFTER F9RK AND
LOW GEAR MUST BE
CORRECTLY ADJUSTED
'
CLEARANCE BE-
TWEEN DRIVING
DOGS OF SHIFTER
CLUTCH AND
'I FORK
CLUTCH GEAR
-
MUST BE
CORRECTLY '
ADJUSTED f
I
.
'
I
·,
.._ SHIFTER LEVER
IN I'<L~ !RA.L '!
•
WHEN ASSEMBLING SHIFTER GEARS

CHAMFERED TOOTH ON SMALL GEAR -
MUST LINE UP WITH PROPER MARK '
ON LARGE GEAR RA PD 310371 j
.. .' ·~ ~ ; . ·~
"
Figure 106-Locations for Measuring End Play of Low and Second RA PD 310314
Gears Between Retaining Bracket and Side Cover Figure 107 -Shifter Forlcs Installed
{6) Reinstall side cover and gasket and securely tighten the five
the gear teeth facing shifter cam gear. The shifter gear is retained on
cover screws and the two stud nuts. Make sure that side cover rubber
oil seal is in place on countershaft. Press inward on countershaft its shaft by the retaining spring. It will be noted that the figure "3"
gear to compress the starter clutch spring; then engage the starter and letter "R" are stamped on the face (hub side) of the shifter gear.
clutch cams under the tripper bolt heads by turning the countershaft The figure "3" mark will be used to time the shifter cam and lever.
so that crank bolt notch is in upward position. This permits easy (3) INSTALL SHIFTER CAM. Before installing the shifter cam,
assembly of end cover to case. Shifter forks and shifter cam can make sure that the shifter finger rollers are in place. Notch in right
now be installed. end of shifter cam is cut out to clear boss in side of case. E_ngage the
f. Install Shifter Forks and Shifter Cam (fig. 107). When in shifter fingers and rollers in the cam slots; tum the cam so that the
stalling the shifter forks, make sure they correctly locate on the shnft chamfered tooth (ground off corner) of the small gear registers in the
with relation to the slots in the shifter cam and the grooves in thr space marked "3" between the teeth of the large gear; then insert the
shifter clutches. The shifter fork spacing (adjusting) washers mny shifter cam shaft (fig. 108). NOTE: See that the small rubber seal
have to be changed in order to obtain the correct distances betwN•n washer is in place in the shaft troove before shalt is installed.
160 161
ASSEMBLY
SHIFTER FORK FOR
(4) INSPECT SHIFTER CLUTCH AND Low GEAR SHIFTER FORK SECOND AND HIGH GEAR
SPACER SHIMS
CLEARANCES (fig. 106). Locate the shifter cam in neutral position so SPACER SHIMS
that the highest points of the high gear driving dogs overlap about O.OCJ7 IN . AND 0.014 IN
78 inch. THICK 0.007 IN . AND
(a) Make Gages. Dress one end of a piece of metal down to 0.083 0.014 IN. THICK
SHIFTER FINGER I BUSHING
inch. This gage will be for shifter clutch and clutch gear (high gear)
measurement. From another piece of metal, dress one end down to BUSHING \ f LOCK WASHER
I.
0.053 inch and the other end to 0.058 inch. This gage will be for
shifter fork and low gear measurement.
(b) Check Clearances (fig. 106). Insert the thickness gage between
'
the driving dogs of the shifter clutch and the clutch gear (over-
lapped about 78 inch) to determine if clearance is between 0.283 and
I
SPACER SHIM 5/64
IN . THICK
BUSHIN'G
NUT
A-SECOND AND HIGH GEAR SHIFTER FORK
SHIFTER GEAR GEAR SHIFTER DISASSEMBLED
CAM
CHAMFERED
TOOTH SHIFTER FORK FOR SPACING SHIM
LOW GEAR SPACER SHIMS 5/64 IN. THICK
0.007 IN . AND 0.014 IN. BUSHING LOCK
THICK TO ADJUST WASHER
SHIFTER FINGER BUSHING
ON· BUSHING NUT
~------~1~--------~~
' ~ rllll/
") '
SHIFTER GEAR TIMING
MARK FOR 3-SPEED TRANSMISSION -
I
I BUSHING SHIFTER FINGER
RA PD 310352 i B-LOW GEAR SHIFTER FORK DISASSEMBLED
figure l08-1ocation of Chamfered Tooth on Small Gear and Position lA PD 310315
"3" on Shifter Gear for Correct Gear Shifter Timing figure l09-Shifter forlcs Disassembled
0.288 inch. Insert the thin gage between the shifter fork and side of (e) Install Inspection Cover. Before installing the inspection
the low gear to determine if clearance is between 0.053 and 0.058 inch. cover, pour about ~-pint of engine oil, crankcase grade, into the
(c) Correct Clearances. The relative adjustment between the transmission case. See that gasket is in good condition and install
shifter fingers and the shifter forks is determined by 0.007 and 0.014 cover, securely tightening the cover screws.
inch thick spacing shims (fig. 109). By increasing or reducing the
number of these shims between the shifter forks and shifter fingers,
a corresponding change is effected in clearance of the shifter clutches.
--
\
I
..._
(f) Install Sprocket, Push Rod, and Cover Assembly. Locate the
two keys on the mainshaft : install the sprocket, lock washer, and
nut and securely tighten the nut by striking the wrench with a soft
Transfer shims as necessary to correctly locate the clutches and hammer. Bend up nut lock washer lip. Install the clutch push rod
reassemble the shifter fork assemblies to the transmission and recheck assembly. Install the sprocket cover and clutch lever assembly, and
clearances. securely tighten cover nuts.
(d) Secure Shifter Camshaft. After correct shifter fork and (g) Install Push Rod Seal and Guide Assembly (fig. 98). Before
shifter clutch adjustment has been made, secure the shifter cam installing the clutch, see that the push rod seal, disk-cup, spring, push
shaft in the case with the lock screw.
163
162
CHAPTER 9
rod guide, and spring retaining ring are in good condition, and in TRANSMISSION (Cont'd)
correct order within the end of the clutch gear. (These parts can be
replaced on the vehicle by removing the clutch outer disk assembly.) Section IV
(h) Install Clutch Hub and Clutch A ssembly. See that the inner
front chain guard is in place before installing the clutch hub. R efer FITS AND TOLERANCES
to paragraph 84 for instructions on clutch assembly.
(i) T est Transmission. Refer to chapter 14. 92. FITS AND TOLERANCES.
-,
• a. Bearings (needle roller) •
' (1) Clutch gear: standard, 0.125 inch x 0.615 inch. Available in
0.0004-inch and 0.0008-inch oversizes.
(2) Mainshaft (sprocket end): Standard, 0.152 inch x Ya inch.
-
Available to 0.001-inch oversize in steps of 0.0002 inch.
'
' (3) Countershaft gear (left end): Same as (2) above.
(4) Countershaft gear (right end): Standard 0.114 inch x ~ inch.
Available in 0.0004 and 0.0008-inch oversizes.
b. Bearing Clearances. All roller bearing clearances to be 0.0006
to 0.001 inch (0.0008 in. preferred).
c. Bearing Races.
(1) Clutch gear roller race in transmission case: Inside diameter,
1.722 inches.
(2) M ainshaft.. roller race in case cover: Diameter, 1.179 inches .
d. Bronze Bushings.
(1) Countershaft left end bushing in transmission case: 0.611-inch
-- -~
diameter.
1 (2) Countershaft bushing in case cover: 0.775-inch diameter.
I (3) Clutch gear bushing: ~-inch diameter.
(4) Low gear and second gear bushings : lo/t 6 -inch diameter.
e. Cam (shifter). Standard hole in shifter cam (drum) ends is
Ys inch. End play in case, free to 0.005 inch.
(1) Clearance on shaft, 0.001 inch.
f. Cam (shifter) Shaft. 0.374-inch diameter.
g. Clutc h Gear. Roller race diameter, 1.471 inches. Refer to clutch
gear bushing d (3) above.
~ h. Countershaft. Small end diameter, 0.609 inch. Roller race (for
! countershaft gear rollers) diameter, 0.7736 inch.
(I) Clearance in case bushing, 0.002 inch.
(2) Clearance in side cover bushing, 0.001 inch.
i. Countershaft Gear. R eplace the countershaft gear when teeth
are badly worn and/ or when roller races are in bad order.
j. Finger (shifter). Roller stud , 0.287 -inch diameter.
k. Finger (roller). R oller inside hole, 0.289 inch; outside diapl-
eter, 0.370 inch. •
I. Fork (shifter) Shaft. 0.37 45-inch diameter.
164 165
CHAPTER 10
m. Fork (shifter) Bushing. Bushing hole, 0.37 5 inch. BRAKES
(1) Clearance on fork shifter shaft, 0.0005 to 0.001 inch.
Section I
n. Gear End Play. Low and second gear end play between the
second gear retaining bracket and case side cover 0.005 to 0.007 inch. REAR WHEEL BRAKE
o. .Mainshaft.
93. DESCRIPTION (fig. 110).
(I) Diameter: End that runs in clutch gear, 0.748 inch. Diameter
at low and second gear positions, 0.9365 inch. Diameter at roller bear- ~
a. The brake is of the internal expanding, two-shoe, fixed -pivot
ing end, 0.87 4 inch. l mechanical type, operated by foot pedal on the right footboard. Brake
(2) End Play: 0.003 to 0.005 inch. • shoes are centered within the drum by shifting the pivot. The shoes
(3) Clearance in clutch gear bushing: 0.002 inch. are operated (spread) by a cam which is actuated by the brake lever.
- -.. Shoes are kept tight against pivot and cam faces by means of two
p. Shifter Clutch Side Clearance. '
coil springs. Adjustment is external, by altering length of brake
(1) Shifter cam must be in neutral position. Clearance between I
I
rod. Bra ke side cover is a ttached to vehicle frame, and drum is
driving dogs on high and second shifter clutch and driving dogs on combined with the sprocket and wheel driving hub assembly. Driving
clutch gear highest point on gear dogs overlapping ·78 inch, 0.053 to hub also operates the speedometer drive gear.
• -
0.058 inch.
(2) Side clearance of low gear shifter clutch, checked between I BRAKE OPERATING LEVER
sides of shifter fork and low gear 0.283 to 0.288 inch.
REAR BRAKE SIDE
q. Shifter Gear Shaft. Diameter of small end, 0.374 inch. Diam- PLATE AND
eter of shaft body, 0.561 inch. SHOE ASSEMBLY
r. Shifter war Shaft Clearance in Bushings.

(1) Shaft end in small bushing, 0.001 inch. SPEEDOMETER
(2) Shaft body in large bushing, 0.0015 inch. DRIVE UNIT
Figure nO-Rear Wlteel Brake
Assembly
~ -
'
I PIVOT STUD
PIVOT STUD NUT
PIVOT STUD PLATE
RA PD 310355
94. RE~tOVAL AND DISASSEMBLY.

a. If brake is in vehicle, remove the rear wheel and brake drum
-_., as instructed in TM 9-879 . Then remove side cover assembly from
I
' vehicle frame after removing the br~ke sleeve nut. If shoes and/ or
liners only are to be replaced or repaired, it is not necessary to remove
the side cover assembly from the vehicle frame.
b. Disassembly.
( 1) REMOVE BRAKE SHOES FROM SIDE COVER. Place end of a
large screwdriver blade between the ends of brake shoes at the pivot
1' -- stud. Move brake operating lever forward to hold brake shoes in full
f expanded position and pry ends of shoe~ off of the pivot stud without
removing the shoe springs (fig. 111).
166 167
REAR WHEEL BRAKE
(2) REMOVE PIVOT STUD AND OPERATING CAM. Remove nut, (4) PIVOT PIN. Inspect pivot pin for bent, damaged, or worn
washer, and plate which secures pivot stud to side cover. Remove condition. Pivot pin diameter is 0.496 inch.
nut, washer, and operating lever from operating cam, and remove (5) SPRINGS. Must be tn good condition.
cam from side cover. (6) SIDE COVER BUSHING. The side cover bushing should show
(3) REMOVE SPEEDOMETER DRIVE UNIT AssEMBLY. Remove the very little sign of wear, unless vehicle has been operated with bushing
screw and retainer and withdraw the drive unit from the brake side nut loose and side cover bearing has worn the bushing. Replace bush.
cover. ing if excessively worn or in damaged condition.
(7) BRAKE DRUM AND SPROCKET. Inspect brake drum for good,
95. CLEANING AND INSPECI'ION. smooth, condition. With brake drum in satisfactory condition, the
a. Cleaning. Clean all parts in dry-cleaning solvent and wipe sprocket can be replaced if badly worn.
dry or air dry.
96. REPAIR.
a. The only repairs to be made to brake side cover assembly is
replacement of parts and relining of shoes. The sprocket can be re·
placed, providing the brake drum is in good condition.
SPEEDOMETER
DRIVE UNIT
REAR BRAKE
..,....- SIDE COVER
ASSEMBLY
NOTE POSITION
OF CAM WITH
RELATION TO
OPERATING LEVER
PRY SHOES OFF PIVOT STUD

-
l
l
OPERATING CAM
OPERATl NG LEVER
ItA 'D JIOSSO
figure U2-0perating Cam and lralce Lever A ...m&led

figure m-Removing lrolce Slaoe•
(1) Refer to paragraph 116 for sprocket replacement.
b. Inspection. (2) Refer to paragraph 97 for instructions covering speedometer
(1) SHOES AND LINERS. Inspect shoes for cracks and breaks. drive unit.
Broken shoes must be replaced. Inspect liners for wear and glazed b. Relining Shoes. Rivets are inserted from the outside, through
condition. Liners worn down to rivet heads must be replaced. If the liner and brake shoe. When lining a shoe, start at one end and
shoes are to be used in replacement service, it is advisable to replace work to the other end in order to make the liner bear tightly against
any found worn or glazed. the shoe and not buckle in the middle, If a liner riveting machine
(2) SIDE CovER. Inspect the side cover for bent and twisted is not available, set the rivets by hand, making sure they .draw the
condition and for wear of operating camshaft hole. Operating shaft liner tight against the shoe.
hole is %6 inch. c. Linkage. Other than straightening slightly bent parts (rods,
(3) OPERATING CAMSHAFT. Operating cam faces must be in good levers, etc.) brake linkage repair is made by replacement of badly
condition. Shaft diameter is 0.558 inch. worn or damaged parts.
168 169
REAR WHEEL BRAKE
97. ASSEMBLY AND INSTAI.I.ATION. (I) CJ·NTI-.H (EQUALIZE) SHOES I N DRUM. Loosen the nut on the
11111 1 p1vot stud, and while applying pressure on the brake pedal (to
a. Install Operating Cam and Pivot Stud. Install the operating 1 1lllrl tiH shoes within the drum) retighten the pivot stud nut. The
cam with the arrow (on end of cam) pointing outward, toward the
t:1111t 1ons 1n the stud plate a nd side of cover will prevent the stud
brake lever (fig. 112). Install the pivot stud, pivot stud plate (ser-
It IIIII shifting after the nut is tightened.
rated side next to side cover), washer and nut.
b. Brake Shoes and Springs. Observe that brake shoes are made c•, AcljuMting Rt>ar Wheel Brak~. The normal free play of brake
for upper and lower positions on the side cover and are not inter - l•u•l pt•dnl before operation is one inch. After brake t a kes effect in
changeable. R ecess in end of shoe for pivot stud head determines posi- v1 h11 lc• operation, the brake foot pedal should have one inch reserve
tion of shoe in assembly. II nvr I before bottoming on the footboard. Adjust brake as follows:
( 1) Engage the ends of springs in shoe casting holes from the ( 1) Disconnect clev1s from brake operating lever and loosen the
c lr Vl'l lock nut on the rod.
inside before installing shoes on side cover.
(:l) Turn clevis onto brake rod to shorten rod and take up foot
pr dnl free play.
(J) Turn clevis off of brake rod to lengthen rod and increase foot
pc·dal free play.
(4) R econnect rod clevis to brake lever and check adjustment,
mnking sure that brake does not drag.
.- .
I
RA PD 310354
Figure JJ3-Installing Brake Shoes on Side Cover Assembly
(2) W ith shoes and springs assembled, separate the shoes so

that the ends will slip over the pivot stud and shaft operating cam
(fig. 113).
--
•
I
c. Install Speedometer Drive Unit. Install the speedometer t
drive unit in the side cover and secure with retainer, lock washer,
and screw (fig. 110). - --
-
d. Installation on Vehicle. Assemble brake side cover assembly to !'

vehicle frame with brake sleeve and nut. Do not tighten nut as side '
cover is shifted in the frame to adjust the rear chain.
( l) CONNECT BRAKE LINKAGE. Connect brake rod end clevis to
the brake operating lever.
{2) INSTALL DRUM AND SPROCKET. Install the drum and sprocket
assembly and install r ear drive chain.
{3) INSTALL WHEEL AND ADJUST CHAIN. Refer to instructions
in TM 9-879 for rear wheel installation, chain adjustment, and wheel
alinement instructions.
170 171
-
FRONT WHEEL BRAKE
move stabilizer. Remove grease fitting, cover plate, spring disk,
CHAPTER 10 bronze disk, stabilizer and bronze disk from side cover.
BRAKES (Cont'd) 100. CLEANING AI''D I NSP ECTION.
Se ction II a. Clean all parts in dry -cleaning solvent and wipe or air d ry.
h . Insp ection . Inspect all parts for bent, worn and/ or broken
FRONT WHEEL BRAKE <'Ondition.
( l) SIDE CovER B USH ING. Diameter, % inch. H as 0.0015-inch
98. DESCRI PTIO!\ (figs. 114 and 115). clearance on axle sleeve.
a. The front wheel, hand-controlled auxiliary brake is of internal- (2) OPERATING CAM BuSH ING. Riveted in side cover. Diameter,
expanding type. Two shoes, on a fixed pivot, are mechanically oper- ~'1 6 inch. H as 0.005-mch clearance on camshaft.
ated. Brake is controlled by a flexible steel wire (stranded cable)
operating with a flexible housing. Brake drum is an integral part of BRAKE STABILIZER PLATE '<*-0PI:RATING LEVER
the front wheel hub. Brake side cover is connected to the rigid fork
by a shackle arm to allow for front fork spring action.
OPERATING CAM M UST BE

ASSEMBLED WITH PROPER
/ RELATION TO OPERATING
·· LEVER
SHOE
ASSEMBLY
RA PD 3 10387
Figure ll5-Front Wheel Bralce Side Cover Assembly (Outside)
(3) OPERATING CAM. Diameter, 0.558 inch.

SHOE ASSEMBLY RA PO 310386
( 4) SHACKLE STUD. Riveted to side cover. D iameter, 0.623 inch .
figure Jf4- front W heel Brake Side Cover and Shoe A ssembly (Inside) C learan ce in shackle arm bushing, 0.002 inch.
( 5) SHACKLE A RM. Steel bushings. Diamet er, % inch.
99. UEMOV AL AND DISASSE:\lBLY. (6) SHACKLE STUD ( IN RIGID F ORK). D iam eter, 0.623 inch .
a. Rt>move W lw d a n (l D isconnf'<'l Li n ka~<'· If brake is in v ehicle, Clearan ce in shackle arm bushing, 0.002 inch.
remove front wheel, following instructions in TM 9-879. Disconnect (7 ) CONTROL WIRE, HOUS ING, AND FITTINGS. Insp ect control
control wire clevis from brake operating lever to free side cover and wire ( flexible cable), housing, clevis and p in , handle a nd all linkage
shoe assembly from control linkage. fittings for good condition. B adly worn, bent, or broken par ts must
h. Disasst>mble Side Covt'r. Remove shoes. Use a large screw- be replaced . Frayed or broken control wire (flexible cable ) must be
driver and spread pivot ends of shoes so that both shoes and springs replaced.
can be pried off of stud and operating cam (fig. 111 ). R emove pivot (8) GREASE F ITTINGS. See that all grease fitt ings are in good
stud and operating cam from side cover. Remove shackle arm. Re- order and are in good working condition.
172 j .~- . 17 3
FRONT WHEEL BRAKE
(9) BRAKE SHOES. Inspect shoe castings for cracks, breaks, or
excessive wear at cam and stud ends. Liners must be replaced when (1) Engage the ends of the springs in shoe casting holes from the
worn down to rivet heads. At time of brake repair, if liners show inside before installing shoes on side cover.
signs of wear, it is advisable to replace liners for shoe replacement (2) With shoes and springs assembled, separate the shoes so that
.
serv1ce. the ends will slip over the pivot stud and shaft operating cam (fig.
(10) STABILIZER PARTS (fig. 116). Inspect the stabilizer hub, 113).
bronze washers, disk, spring, and cover plate for good condition. c. Installation on Vehicle. Refer to TM 9-879 for installation and
Replace any badly worn or damaged parts. adjustment instructions.
101. REPAIR.
a. Side Cover. Other than replacing the bronze bushing in the
side cover. repair to the side cover is not recommended because of
structural design. All other worn and/ or damaged parts of brake and
linkage must be replaced.
FRONT BRAKE SIDE COVER ASSEMBLY STABILIZER

ASSEMBLY COVER
BRONZE FRICTION SPRING
WASHE W HER
NUTS
\
•
. v
'' .
.
> ~, .
''!.;·
< I
.•... .
.' .' .
\~ · GREASE
'
FITTING !
I
BRAKE
PLATE
RA PO 310402
Figure 116-Front Brake Stabilizer Disassembled
h . Brake Shoes. When relining brake shoes. start from end of -
I
liner and work toward the other end in order to make the liner lay I
I -
tight against the shoe. Rivets are passed through the liner from the
outside and are set against the shoe.
!
102. ASSEMBLY AND INSTALLATION. I
a. Install Operating Cam and Pivot Stud. Install the operating

cam with the arrow (on end of cam) pointing outward, and with
brake lever at right angles to cam (fig. 114). Install the pivot stud,
pivot stud plate (serrated side next to side cover), washer and nut.· •
b. Brake Shoes and Springs. Observe that brake shoes are made
for upper and lower positions on the side cover and are not inter-
changeable. Recess in end of shoe for pivot stud head determines
position of shoe in assembly.
174
175
WHEEL RIMS AND SPOKES
Spokts on hub flange side; 20 used, 8H inches long.
CHAPTER 11 Nipples, 40 used.
(2) REAR W HEEL.
CH~INS, SPROCKETS, WHEELS, AND HUBS Rim, 18-inch, 40 holes (identified by "XF 705" stamped near tire
valve hole).
Section I Spokes. 40 used. 85:::! inches long. and 0.161-inch diameter.
WHEEL RIMS AND SPOKES Nipples. 40 used.
103. DESCRIPTION AND OAT A. 1 0~. I ~SPF.CTION.

a. Description. Both wheels a re wire sp oked with 40 spokes in a. W heel rims must be inspected for bent. twisted a n d kinked·
each. Front and rear wheels are no t interchan geable. 18-inch drop condition and condition of nipple holes. Replace badly bent, kinked
center ri ms accommodate 18-inch x 4.00-in ch drop cent~r tires. R ims
a re not interchangeable because of spok e nipple diameter and angles.
Front wh eel rim is identified by "SF 705 TA" stamped near valve
RA I'D 41 0414
-
I .
Figure US-Removing Rear Wheel Mounting Screws with
l . Wrench (41-W-3832)
and twisted rim, or rim with nipple holes pulled out. N OT E: Do not
replace spokes or bearings until condition of hub is ascertained.
ItA I'D 310401
Section II of this chapter.
b. Sp o k t>s a nd 1\ipples. All spokes and nipples must be in good
Figure JJ7 -Dimensions lor Correctly Centered Front and .....
I I condition and each spoke tightened to carry its load in the wheel.
Rear Wheel Rims I Bent, cut, and stripped thread and / or broken spokes must be re-
placed. N ipples must be in good condit ion.
hole. Rear wheel rim has larger nipple holes a nd has number " XF ('. Trut>n ess and Corre<·t Him Cf'nt e rin~. Wheel assembly must
705" stamped n ear valve hole. Rims must be centered on hubs for be inspected for true running rim and rim center in relation to hub
correct alinem ent on v eh icle. (fig. 117 ).
b. Data.
(1) FRONT WHEEL . 105. SPOKE REPLACF.:\IENT.
Rim, 18-inch , 40 holes ( ident ified by "SF 705 · TA" st amped near a. Wheels must be removed from vehicle for spoke replacement.
tire va lve hole). Usc special wrench ( 41-W -3832) to remove mounting screws when
Spokes on brake flange side; 20 used, 5% 6 inch es long.
17 7
176
•
CHAPTER 11
removing rear wheel (fig. 118). Replace any damaged, bent, broken CHAINS, SPROCKETS, WHEELS, AND HUBS (Cont'd)
or stripped thread spokes. Use wrench 41- W -3340 for rear ~heel
spoke nipples, and wrench 41 -W -3339 for front whe.el spoke mpples Section II
(fig. 119). R eplace any nipples not in good conditwn. Where only
several spokes are replaced, tighten accordingly, and see that wheel WHEEL HUBS
rim is true after spoke tightening.
108. DESCRIPTIO~.
106. LACE WHEELS. a. Rear Hub (fig. 120). Knock-out axle with roller bearing hub.
a. Wheel lacing is a most difficult procedure to describe, even Fourteen Y4-inch rollers used 'on brake end and twelve Y4-inch rollers
with pictures. The best and surest method is to follow the pattern of a used on the other (outside) end. (Rollers are 0.490 in. long.) End
wheel already laced. play adjustment is made by shims. Bearing wear is taken up by use
.I' of oversize rollers. To take up excessive side play only, it is not neces-
FRONT WHEEL sary to completely disassemble hub (par. 110).
NIPPLE WREN h. Front Hub (fig. 121 ) . Knock-out axle. Ball bearing hub.
adj ustable cone similar to bicycle hub design . Thirteen 5 141 .inch balls
used in each end. No ball retainers used. Front hub and brake shell
are of integral construction. Grease gun lubrication .
.109. REAR HUB DlSASSE \IBLY.

a. Rf>mov(' Lt-ft Sicle (Brake Sidt-) Components. Remove five
thrust bearing cover screws and washers. Then remove thrust bearing
outer cover. cork grease retainer. thrust bearing h ousing, and gasket.
Remove thrust hearing adjusting shims (shims are 0.002 inch thick),
thrust washer. thrust bearing sleeve. and remaining thrust washer.
Roller retainer, rollers, and left side (brake side) roller retainer
thrust washers are then removed.
NIPPLE WRENCH
b. Remove Ri~ht Sid.- ( Sprockt-t SidP) ComJIODt-nts. Remove
,.._. { RA PO 310407
retaining lock ring from right side (sprocket side) of hub and remove
cork retaining washer and hub inner sleeve. Then remove cork washer.
figure rJ9-front and Rear Wheel Spoke Replacement, Using Spoke retaining lock ring. roller bearing washer. and roller retainer and
Nipple Wrenches (41-W-3340) Rear and (41-W-3339) front rollers. The right side roller retainer washer, pressed into the hub
shell, need not be removed. This washer is assembled in all new hubs.
107. TRUING WHEELS.
110. REAR HUB CLEANI:\G, I~SPEC.TION, AND REPAIR.
a. Mount in Stand. Mount wheel in truing stand, and adjust
stand gages to determine position of rim as regards side wobble and a. CIPaning. Clean all parts in dry-cleaning solvent and wipe
eccentricity. or air dry.
b. Center and True Rim. Use wrench 41-W-3340 for rear wheel b . lnSJ)f'<'tion. Inspect for good condition as compared w1th new
spoke nipples and wrench 41-W -3339 for front wheel spoke nipples parts. Hub clearance on the rollers is 0 .0005 to 0.00075 inch. End play
(fig. 119). When tightening the spoke nipples, bea~ in min? that the of hub on the inner sleeve is between 0.003 and 0.005 inch. Inspect
rim must be centered in relation to the hub. From ttme to ttme, check roller races within hub and on the inner sleeve for signs of wear or
the distance from the rim to the straight edge (or a point on the tru- roughness. Cork washers must be a snug fit on their seats to effect
ing stand) to determine rim center. good grease seal.
(1) True rim so that side weave or wobble and eccentricity are c . ltepair. The only repair that can be made to the rear hub i"'
within lflu inch of true. replacement of worn or damaged parts and the adjustment of huh
(2) Tighten all nipples so that each spoke is carrying its share of end play on the inner sleeve. The hub end play can bt• 11d 1uo;tnl
without complete hub disassembly. as follows:
the wheel load.
178 179
I C D F G H K L M N 0 P 9 S T
\ \ l 1\ ~ l ~1 ~ l
(110 :(! ) ~) ~i '~\~~~\)
..........
' + J
~
•
A - THRUST BEARING COVER SCREW L- LEFT ROllER RETAINER THRUST WASHER
B - THRUST BEARING COVER SCREW WASHERS M - HUB SHEll (SECTIONED)
-
00
0
C- THRUST BEARING OUTER COVER
D - CORK GREASE RETAINER
E - THRUST BEARING HOUSING

N - RIGHT ROllER RETAINER
0 - HUB INNER SLEEVE

WAS~I(R (PRESSED INTO HUB SHEll)
P - ROllER BEARING ASSEMBLY (RIGHT END)
F- THRUST BEARING HOUSING GASKET 9- ROllER BEARING WASHER
G -THRUST BEARING ADJUSTING SHIMS (0.002• THICK) R -RETAINING lOCK RING (2)
H -THICK THRUST WASHERS (2) S- CORK GREASE RETAINER
J- THRUST BEARING SlEEVE T- CORK RETAINING WASHER
K - ROLLER BEARING ASSEMBlY (LEFT END) U - GREASE FITTING
RA PO 310283
figure J2u-leor Wlteel Hub Disossembled
A I c D E F G D H J K L M
I
0 1."-
C)
0 ()
0
0 0
0
0
0 § J£;·\ 0i ,J,: IJlJ VI ~
0 0 ::z:: •
--
00
0
0
0
0
Cl'
0
0
O
0
G - G REASE FiniNG
"'
"',..
:z:
c
A. - GREASE DEFLECTOR (PRESSED ON HUB)

H - ADJUSTING CONE
"'"'
J - ADJUSTING CONE LOCK WASHER
I - CONE SPRING RING
K - GREASE SEAL
C -FRONT AXLE SLEEVE AND CONE (INTEGRAL PART)
D- 5/16 INCH STEEL BALLS (13 IN EACH END) L - GREASE SEAL RETAINER
E - GREASE DISTRIBUTING SLEEVE M - ADJUSTING CONE LOCK NUT

F -FRONT HUB AND BRAKE SHELL ASSEMBLY
RA PO 310214
figure l2l-front Wheel Hub Disassembled

•
WHEEL HUBS
(.:1) Install one of the thick thrust washers: th<-n tlw thrllst bdlr-
(1) ADJUSTING HuB END PLAY WITHOUT CoMPLETE Dis- ing sleeve: then tht: remaining thick thrust washer.
ASSEMBLY (fig. 122). Remove the five thrust bearing cover screws and
lock washers. The cover, cork washer, and thrust bearing housing may (5) Install the thin adjusting shims.
then be removed, exposing the thin adjusting shims (0.002 in. thick). ( 6) Install paper gasket.•.thrust brF.J ring housing. cork grease
Add one or more shims and reassemble all parts removed and securely ' retainer, and bearing outer cover. Draw up thf' tivt· covtr sct cws tight.
I
tighten cover plate screws. Try hub for end play on the thrust bear- ' (7) Hub is now ready to check end play adjustment.
ing sleeve. The cork retainer will interfere to some extent with free h. End Play A•l.iuslnH·nt (fig. 122) . End play adjustment is made
movement of the thrust sleeve. Select washers to give 0.003 to 0.005 by adding or removing thin steel shim washers (0.002 in. thick) in
inch hub end play on the thrust bearing sleeve. CAUTION: Be care- the left end of the hub. The correct hub end play on the thrust lH·aring
ful not to add too many shims and thus bind the thrust bearing sleeve. sleeve is 0.003 to 0.005 inch . Tilt- cork grease retaining washt·rs may
cause some drag on the thrus1 lxnrmg; sleeve, making it difficult to
INNER THRUST THRUST BEARING determine whether the thrust slt:t"Vt· is free (0.003 to 0.00:1 -in. end
WASHER IN PLACE SLEEVE, WASHER play) . The hub .must have the required end play and be free o n the
roller bearings to ensure most satisfactory service l1ft' R emove or
AND SHI add shims as necessary to obtain correct end play, rcasst·mbling ldt
end parts each time to make the end play check.
( 1) HuR LuRt~l C ATION . After final as~embly, inject 1Y4 ounres of
general purpose grease with aid of grease ;;un.
112. FRONT HUR DJSASSEi\IBLY.

HOUSING COVER
a. Remove nut from right end of hub and remove felt seal re-
AND GREASE tainer, cone lock. and cone from axle sleeve. Felt seal will come out
RETAINER""' with the cone. The balls are free to fall out, no retainer being used.
ASSEMBLY ~
~ .... b. Pry the grease deflector from the left end (brake side) of the
hub and withdraw axle sleeve and cone assembly.
c. Grease distributing sleeve furnished on late models can be with-
drawn from hub shell.
SCREWS 113. FRONT HUB CLEANING, IN~PEf:TIO:\', A~D HEPAIH.
f.ce ItA PO 310399

a. <:lt>aning. Clean all parts in dry-cleaning solvent and wipe or
air dry.
b. Inspection. Inspect all parts for good condition, paying atten-
tion to ball races in hub shell and on cones. Pitted or worn ball races
Figure J22-Parts Removed far Adiusting Rear Hu& End Play makes part replacement n ecessary. Inspect brake shell for d<' CP
grooves and worn condition and see that spoke flanges are true and
111. REAR HUB ASSE.\fBLY AND ADJUSTMENT. not damaged. If steel bal ls show signs of wea r and are pitted, replace
a. Assembly (fig. 120). Select rollers to give 0.0005 to 0.0007 5 them.
inch clearance on the inner sleeve. When trying for roller bearing c. Ret•air. The only repair to the front hub is replacement of worn
clearance, bearings must be free from grease or oil. After correct size or damaged parts and cone adjustment.
rollers have been selected proceed to assemble hub as follows:
(1) Apply general purpose grease to rollers and races and install 114. FRONT HUR ASSE:\IHLY AND ADJUST:\IEl\T.
right end bearing in hub, open end of retainer out. Install the roller
a. Assf'mhly. Retain balls in hub shell races with grease. Instnll
bearing washer and the retaining lock ring.
the grease distributing sleeve: fill inside of grease distributin~ sk< vt
(2) Install hub inner sleeve, cork grease retainer, cork retaining with grease before assembling on axle sleeve. Install the gn·nsl' tli'l
washer, and outside retaining lock ring.
tributing sleeve on the axle sleeve and co:1~ assembly. an<! rtS!Ilt'llll•lt
(3) Install left side roller retainer washer in hub and roller bear- to hub from the left (brake) end. Press grease dcllcct{)l rin~~ 1111 h11h
ing assembly with open end of retainer out.
183
182
WHEEL HUBS
After final assembly. make o bt'aring check to be sure cones are not
too tight.
(1) Ht;B LunR rC,\TIO l ;..;tcr Jinal ass~mbly, inject one ounce of
general purpose grease.
c. Ex(·t>ptions. Front v.:het-1 hubs on earlier models did not have
grease distributing sleeve nor felt grease seal. When the felt grease
seal was first assembled on model WLA front wheel hub. the co::1e,
cone lock and nut diff trt>d from des1gn illustrated in figures 121. 123
and 124 of this manual. F or dcscriptton of this assembly, refer to
TM 9-879.
(1) Grease ddlector sleeve can be installed in any WLA model
front wheel hubs to direct grease to balls and races.
(2) F elt grease seal can be installed in any earlier WLA model
front wheel hubs by replacing original parts with items H , J, K , L
and M , figure 121.
figure 123-Cone, Lode and Nut in Position to Adjust front Wheel

Bearing Play
figure 124-Tightening Searing Cone Loclc Nut After Adjustment
Turn on the right end cone; install cone lock and nut. Leave out felt
grease seal and seal retainer until thrust adjustment has been made
(fig. 123).
b. Adjustment. Adjust cone so that wheel rim has slight side
shake when axle sleeve nut is tight; then remove nut and apply a
slight amount of grease or oil to felt seal for initi~ll lubrication and
press firmly in place; then install felt seal retaining washer. Nut can
now be turned on sleeve and tightened for final assembly (fig. 124).
184 185
CHAINS AND SPROCKETS
b. To Tighten Slightly Loose Sprocket.
CHAPTER 11 ( 1) If sprocket is only very slightly loose and rivet holes are not
elonga.ted.' remove 6 o f the rivets (every fourth rivet as in fig. 125)
CHAINS, SPROCKETS, WHEELS, AND HUBS (Cont'd) by c~u~elmg o.ff heads (hub side) and punching out rivets. Reset
remammg 18 nvets, using special riveting jig (No. 41-J-373) and con-
Sedion Ill ~av~ pun~h . Lock jig securely in vise, set drum and sprocket assembly
m Jig, With sprock~t up. Place slotted washer between spring on jig
CHAINS AND SPROCKETS an? s~eedometer dnv~ gear on drum, and turn knurled spring tension
adJUStmg nut down bghtly against spring. Spring tension holds rivet
115. DESCRIPTION. ht:ad ?rmly in anvil socket to ensure a good, tight, riveting job on
a. Sprockets. each nvet and dov.:el pin. With spring tension properly adjusted, drum
assembly can be hfted far enough to permit turning sprocket so any
(1) ENGINE SPROCKET. Standard sprocket on WLA m?del h~s
31 teeth. Sprocket is %-inch pitch for double-row roller cham and ts
taper fit on flywheel shaft with Woodruff key.
(2) CLUTCH SPROCKET. The clutch sprocket is an integral part
of the clutch shell assembly and also serves as outer race for clutch
hub ball bearing. When worn or damaged, the sprocket and hub shell
assembly must be replaced.
(3) TRANSMISSION COUNTERSHAFT SPROCKET. Standard sprocket
on WLA model has 17 teeth, sprocket is %-inch pitch for single-row
roller chain and is taper fit on transmission mainshaft with two
Woodruff keys.
(4) REAR WHEEL SPRO_<:KE:. The 41-to?th, ~-inch pitc? s~ro~ket
is secured to brake drum wtth etghteen %:?-mch nvets and stx ~ 1 G-mch
dowel pins. Refer to paragraph 116 for replacement instructions.
b. Chains.
( 1) FRONT CHAIN. The front roller chain is endless, of double-row
type, having 100 links of %-inch pitch. Chain is lubrica~ed from
engine lubricating system and provided with separate adjustment.
Front chain is adjusted by shifting transmission backward or forward
in frame mounting.
(2) R EAR CHAIN. The rear roller chain is sin~le~row, %-inch
pitch and is 58~ inches long when .new. Rear c~a1~ 1s se.cured on
sprockets with a connector (master) hnk. R ear cham IS lubncated by
engine lubricating system and provided with separat~ a~justment.
Supplementary lubrication provided by ex~er~al ~pphcatton ~r .by
soaking chain in lubricating bath. Rear cham ts adjusted by shtftmg
rear wheel axle backward or forward in frame stay clips. (fig. 126) .. If old style jig (without spring and washer assembly
~ttached.) ts used, care must be taken to see that rivet head seats well
116. REAR WHEEL SPROCKET. mto anvtl socket, whe~ heading rivet. Or a long bolt with nut, 2 large
a. On later WLA models the rear wheel sprocket is assembled on ~at. w~shers, and a spnng can be used (through center of jig) to make
tt stmtlar to late style jig.
the brake drum with eighteen %2 -inch rivets and six :~'1 ~;-inch dowel
pins. Sprocket rivets only on earlier models may work loose and . (2) After rivets have been reset, redrill the 6 holes from which
elongate the rivet holes. making sprocket replacement necessary. :tvets :"'ere removed, using a 'YJ. 6 -inch drill. Drill from hub side, hold-
The rear wheel sprocket only is furnished with twenty-four ~~~2-inch mg dnll. as steady. as possible and at right angles to sprocket face so
holes and the six ~'11 ;-inch dowel holes must be drilled after eig~te~n .ho~es Will be. stratght and to size. Insert dowel pins, with heads on
rivets have been installed. If inspection shows rear sprocket tS m tnstde (hub stde) of sprocket (fig. 126). After inserting dowel pin11,
worn condition and rivets are loose, service as follows in b , c, and d , p~ace s~rocket and drum assembly on riveti •• g jig and fully seAt dowd
of this paragraph. pms, usmg hollow punch. Head the hollow (outer) end of dowrl p1111
186 187
CHAINS AND SPROCKETS
d. Fitting Nt'w Sprockt-llo l"seu Brakt~ Drum.
~ r•ounch not only forms a head but (1) When necessary to r eplace rear sprocket with a new sprocket
OtJ) s~ o they completely fill their holes. due to worn teeth or badly elo:1gated rivet holes, or both, chisel off
b ,, heads of all rivets and punch out rivets. If the assembly is one with
tli!!Se Sprocket, with Rivet Holes dowel pins, mark the dowel pin holes in drum before punching out
8 ··:• •I
~I. · : rivet holes do not appear to be
dowel pins and rivets. Sprocket can then be removed and discarded.
1 1 'I~ (2) Carefully inspect brake drum. If original holes are badly
!~,. ' ettat and sprocket is otherwise in worn and elongated and outside diameter of drum flange is worn so
h·~ ' ff heads of all rivets and punch
..'Ii• "~·:._ it is a loose fit in counterbore of new sprocket, drum also should be
PI< rt..· ea'tds on h~b side), skippi~g every discarded and a new, complete sprocket and drum assembly installed.
~ I'I · ~ ~.1 r:aslih ring 1s damaged or 1ts holes If holes are found elongated to some extent, but drum flange is still
C·: 'I
)~·~j a fairly close fit in counterbore of new sprocket, and drum is in good
1'•'t1 .. asSO!Sembly on riveting jig and fully
'' '
~~.\ condition otherwise, a new set of holes can be drilled in drum flange,
~
I'~·I·~\~
(llhub side) of sprocket and at the midway between original holes. When redrilling, use new sprocket as
~ c-
~\:
,1.•, ~
',::;b,•.
1~a~;
I •
'·I ~· ~:
REAR DRIVE CHAIN DUAL FRONT CHAIN .J

RA PO 310405
figure 127 -Replacing front and Rear Chain Links wirh

Tool (41-T-3320)
a template for locating holes. Sprocket must be installed in same

manner as it is installed in final assembly and with flange on brake
drum registered in counterbore of sprocket. When rep~:~iring in this
manner, block up sprocket and drum so they rest on blocks rather
than on speedometer drive gear on drum hub. Use thin boards or other
available material of required thickness. Drill one 5~{:?-inch hole and
insert rivet. N ext. drill hole directly opposite first hole and insert
1 itr'l 11 bly tight together, using hollow rivet. These rivets will hold sprocket and drum in exact relation while
~~~ , (outer) end of rivets, using con- drilling r emaining holes. Now drill remaining 22 holes with %2 -inch
l r'tv'~ets
as the first one, then head the drill. Remove the two rivets and sprocket from drum and completely
1
1 'ile~t. head the two r.ivets midway remove burs from newly drilled holes with a file. Replace sprocket
\~~dl the remaining 14 rivets. As each on drum, install splash ring and insert 18 rivets (with h~ads on hub
to;··y to heading, again use hollow !lide), leaving every fourth hole open for dowel pin, and head all rivets
\\te~ and parts of assembly are tight 't•curely. Follow procedure given in c (2) of this paragraph, when
I')'.:. htading rivets.
1 ".·
:,1~~di·led securely, redrill the six open (J) After rivets have been headed securely, redrill the six own
\4r·tt dowel pins as explained in b (2) hole'~ and fit dowel pins as explained in h (2) of this paragruph
189
CHAPTER 12
Bear in mind when new sprocket is being installed on used drum and
origin al drum holes are being used again; that if drum has already STEERING SYSTEM
been drilled for dowel pins, care must be taken to see that dowel pins
are again fitted in same holes. Section I
FORK
117. CHAINS.
a. Except in case of emergency, repair to drive chains is not good 118. DESCRIPTrON.
practice because chains are generally worn excessively at time of a. ~he WLA model f~r~ is composed of two members; namely,
breakage and should be replaced. B oth the front and rear chains can the. sprmg f~rk and the ngtd fork. The spring fork consists of two
can be repaired by removing the broken link · and installing repair spr~ng fork st~: assemblies to absorb shock and recoil during service
links. Inspect both chains for broken or lost rollers, loose pins, and action. The ngtd fork stem passes through the frame head and with
cracked side plates. t:?~ two side as.sem?lies, attaches to the handlebars for steerin~. The
ngtd fork bearmg m the frame head is provided by thirty ~~ -inch
b. Chain Wear. Determine chain wear with regard to replacement
as follows:
6
SIGHTING ROI).S
(1)
(2) FRONT CHAIN. The front chain is endless. Front chain is 1

..
either in serviceable condition or rusted, damaged and worn beyond
further use. Inspection will reveal condition as to further possible
good service.
c. Chain Link R e place m e nt. Use chain tool (41-T -332 0) to push
out link pins in order to install repair links. Refer to figure 12 7 for
correct use of chain tool on both front and rear chains.
RA PO 310374
Figure 128- Visual Checlc ol Fork Side Alinement
~a~ls, cones and frame head cups. Lower ends of the spring and
~tgtd forks are att~ched to rocker plates which provide the mount-
mg and rocker actton for the front whe~l. Forks are heat treated and
bent forks can be straightened and alined witho ut preheating.
119. INSPECTION.
a . . Gent>ral. F orks and components must be cleant'd with dry .
clconmg solvent or by stea.m so that cracks will c;how up in insp<·ct io11
~· okt n or hacfly bt'nt sp~mg forks a~d 1 igici fork'! nn 1"t h< n pt 111 rd
Forks not hndly hcnt or m nc<'d of nluwmt nt t'lln he: lltluinlllr urcl
190
191
FORK
b. Spring Fork._ Inspect the spring rods for straightness, aline
ment, wear at _bushmg contact point and for good thread condition. (4) CuSHION BuFFER SPRING. Free length 37) 6 inches. R eplace
I_nspect for~ s1des for cracks. Use two straightedges to check fork when broken or shrunk Ys inch.
stdes for ahnement. Broken or badly bent and twisted spring fork (5) SPRING Ro o BuSHINGS. Hole d iam eter 0.505 inch. Clearance
must be replaced. -.,. on fork spring rods 0.005 inch.
c. Rigid Fork. Inspect for cracks and breaks condition of stem ! e. Rocker Plates and Studs. T he rocker plates are steel bushed
threads and. ends which engage handlebar bracket: Broken and badly • a nd have 0.004 to 0.005 inch clearance on the fork tip studs. Replace
bent and tw1sted forks must be replaced. bushings and/ or studs when clearance is excessive.
. (1) CHECK FOR !WIST. Use the visual check of fork side relative (1) Bushing hole diameter is 0.751 inch.
ahnemen~ as shown m figure 128. Use two ~'i 6 inch diameter bars, at (2) Stud diameter is 0.747 inch.
least 18 mches long. Pass one bar through stud holes and lay the
other bar acro~s the _stem ends of the fork sides. Sight along the two 120. STRAIGHTENING FORKS.
bars to determme tw1st.
a. Both the spring and rigid forks are heat treated steel and can
A be straightened and alined cold, without disassembly, providing bend
1"1
u -1---
-----~....
- -H ft-fi- -
/
/ ' - ,....,
'-'I
is not more than 4 inches from no rmal alinement and twist is not
more than 2 inches from normal alinement. The steel in a bent or
twisted fork in exce5s of these limits would be weakened, and possibly
SIDE VIEW STRAIGHT WITH CENTER LINE fractured, making further use unsafe.
9 b. Tools and Fixtures. Some satisfact ory m ethod for holding fork
OTE: THESE ENDS and applying leverage at the correct points must be provided. A large
SPACED TO FIT press or surface plate provided with hooks and pry blocks must be
HANDLEBARS ~~---~fL___ _...;=.>=,.·f used. Alinement of forks must also conform to alinement of new
forks (by comparison) after straightening.
3-23/32 IN.
121. FRAME HEAD BEARINGS.
a . Description. Ball cups are pressed into the frame head to hold
__,~,
IN. DIA. x 29-1/2 IN . LG. fifteen ~) 6 "inch steel balls (without retainer), upper and lower. A
stationary cone is pressed onto the rigid fork center stem for the
STRAIGHT ROD
3-23/32 IN lower bearing race to float on, and an adjustable cone screws onto
upper end of fork stem for upper bearing race to float on.
l
b. Inspection. Inspect h ead cups and cones for pits, cracks, or
RA PD 310375 worn condition. Inspect steel balls for pits. Replace damaged, broken,
Figure l29-Dimensions for Forie Side and Forie Stem Alinement or worn parts as compared with new parts.
(2) <:H~CK FOR STEM AND FORK SIDE PARALLEL ALINEMENT (fig. 1
,, 122. STEERING DAMPER.
129). Th1s 1s a rough check. Pass a ~) 6 inch diameter bar, 30 inches ' a. The steering damper is an accessory, manually adjusted to
l~ng, through the fork center stem. Measure distance between fork apply friction to the front fork and prevent vehicle wobble in rough
tips and test bar. When fork sides are parallel to center stem distance
w ill b e 323/ • h
·,:12 me es.
see that fork upper ends are alined .to fit the terrain or at high speeds. Repair to steering damper is made by parts
replacement.
handlebar bracket mounting holes.
d. Springs and Bushings.
(1) RECOIL SPRING. Free length, approximately 5~ inches. Rc
place when broken or shrunk 7'8 inch.
(2) BUFFER SPRING. Free length approximately 3Ya inches. Re-
place when broken or shrunk Ya inch.
(3) CuSHION SPRING. Free length 6Yt 6 inches. Replace when
broken or shrunk Ys inch.
192
193
-
HANDLEBARS AND CONTROLS

will provide lev~rage, taking care not to kink or dent the tubing 10
CHAPTER 12 the straightening process. Refer to figures 130 and 131 for alinement
specifications.
STEERING SYSTEM (Cont' d)
Section II
125. REPAIR.
a . B adly bent or broken handlebars must be replaced to ensure
HANDLEBARS AND CONTROLS highest safety factor in service. T he control components can be
• replaced. D amaged threads in ends of handlebar can be cleaned u p
''
123. DESCRIPTION. I with t ap as shown in figure 132.
a. Handlebars are of welded construction and are heat-treated for
strength. Do not weld handlebars. The only repair that should be •
attempted is straightening of handlebars. The handlebar bracket
attaches to the rigid fork side bar and outer stem ends. Control wire '
HANDLEBAR END TAP
RA PD 310411
Figure 130-lnspecting Handlebars for Width
HOLD BARS ON ----..

LEVEL SURFACE
lA PO 110413
figure 132-fapplng Handlebar End with fap (41-f-1026)

4-1/4 IN
--
"""······!.. BENCH SURFACE
figure J3J-Inspeding Handlebars lor Height

RA ..0 31041 ;.\
plungers (spark and throttle) a re actuated by spirals in the grip

sleeves. The grip sleeves are retained on the handlebars by means of
end screws. Badly bent or broken handlebars must b~ replaced and
damaged or worn components must be replaced.
h . Re pla<'ing Contro ls. Refer to TM 9-879 for instructions cover
ing handlebar control wire and housing replacemen t.
124. H ANDLEBAR ALINEMENT.

a. If handlebars are not bent sufficiently to kink, fracturC' or
weaken the tubing, they can be alined cold by mounting the brot•kt·t
[
and bending the bars back in shape. A long pipe p laced over the bor
194 195
FRAME AND TANKS
preted o f misalinement, ca n be made with a straightedge and a bar
( fig. 133) . The (; ~~ 4 -inch t-ar is passed through the frame head (ball
CHAPTER 13 cups installed and with th•· straightedge placed along the side )f the
fram e ) , measurement of rear fork stay clips and distance from head
CHASSIS PARTS AND EQUIPMENT bar to s traightedge determines alinement.
b. S traightening and Alining Frame. When rough check, or
Section I
visible signs reveal frame m isalinement, .straightening and accurate
FRAME AND TANKS measurem ent must be done on a surface plate provided with holding
fixtures, leverage tools and accurate gages. Special instructions
accompany such equipment.
126. DESCRIPTION.
a. Frame. Steel forgings, st eel castings, and steel tubing are
assembled and brazed together making the frame an integral part.
128. TANKS.
Reinforcing is p rov ided at vital points and the frame is heat treated a. If tanks are badly smashed, damaged, or dented they must be
for additional strength. A frame that is not too badly bent can be replaced. Minor dents, leaks and damage can be repaired by use of
torch, taking necessary safety precautions when applying heat or an
open flame to the fuel tank.
13/64 IN
t z
5-5/32 IN
l - ID
STRA IGHTEDGE 3- 13/ 32 14 '~

FRONT UPRIGHT FRAME TUBE
1/16 IN THICK SHIM BETWEEN
FRAME TUBE A ND STRAIGHTEDGE
DIA x 26 IN
LONG HEAD
1/ 16 IN. THICK
SHIM
BAR
STRAIGHTEDGE •
RA PD 310400
figure 133-Checking frame Alinement wirh Straightec:lge
straightened and alined cold, provided suitable fixtures and alininK

devices are at hand. A broken frame, or a frame bent to such ext<'lll
the tubing or castings are weakened, must be replaced in the intcn·'lt
of safety in service.
b . Tanks. Tanks are of welded steel construction. All fittinll" nrr
either welded or riveted in place. The right tank is used for t' rllllllf:
oil. The left tank is used for fuel.
127. FRAME ALINEMENT.

a. Rough Ch eck for Fram~ Aline~ent. A sati~foctory mttluul
of rough checking a frame that 1s not v1s1bly out o f hn<', yet 1t 111 aus 197
196
MUDGUARDS, CHAIN GUARDS, STANDS, AND SKID PLATE
b. Rear Stand. Rear stand supports vehicle in an upright posi
CHAPTER 13 tion. Stand is of welded construct10n. A badly bent, twisted, or
broken stand must be replaced because insufficier.t strength remains
CHASSIS PARTS AND EQUIPMENT (Cont'd) in a damaged stand that has been straightened or welded.
Section II 132. SKID PLATE.

MUDGUARDS, CHAIN GUARDS, STANDS, AND a. When the skid plate becomes so badly damaged it cannot be
SKID PLATE assembled to the vehicle without unnecessary work and time, it
should be replaced. Owing to design of skid plate, it is difficult to
aline, once twisted.
129. MUDGUARDS.
a. Front Mudguard. If front mudguard is badly bent or broken,
repair is not worth while because future service will be limited. If
stays or stay brackets only are bent or broken, they can be replaced.
b. Rear Mudguard. The rear end of the rear mudguard is hinged
to the front section. Broken stays or stay brackets can be replaced.
'' '
If mudguard is badly bent or broken, satisfactory repair cannot be
made.
I I
NUTS AND WASHERS
LEG
U-BOLT
BUSHING
SPRING
BRACKET
J . . --SPRING
_.S)- - - - - - P L AIN WASHER

"'J·- - - - - - LOCK WASHER
~.. NUT
lA PO "0396
figure 134-Jilfy Stand Disossemblecl
130. CHAIN GUARDS.

a. Front Chain Guard. The front chain guard is in two parts,
the outer (cover) guard and the inner guard. When chain guard is
not too badly bent or dented, it can be straightened and made serv-
iceable.
b. Rear Chain Guard. The rear chain guard can be straightened
when bent and a damaged mounting stud can be replaced.
131. STANDS.
a. Jiffy Stand. The jiffy (side) stand is used as a prop and cnn
be folded up out of the way, before vehicle is put in motion. Repoas
to the jiffy stand consist of parts replacement (fig. 134).
199
198
1. i
CHAPTER 13
CHASSIS PARTS AND EQUIPMENT (Cont'd)
CHAPTER 13
Section IV
CHASSIS PARTS AND EQUIPMENT (Cont' d) '
I SADDLE AND SADDLE POST
Se ctio n Ill '
BAnERY BOX, TOOL BOX, AND FOOTBOARDS I :i6. SADDLE .

.a. A ~adly bent, twisted, cut or worn saddle cannot be repaired
133. BATIERY BOX. With satisfactory results. Replace a ny saddle considered not safe
nnd services ble.
a . The battery box is of unit construct_ion and other than taking
out dents, replacing cover hold-down bolts and repainting, it cannot 137. SADDLE POST (fig. 135).
be repaired. The battery box is in a protected location and battery
acid corrosion causes the most damage. a. Spring saddle post can be taken apart, and broken, or dam-
aged springs, spring rod, and fittings can be replaced.
134. TOOL BOX. PLUNGER PLUNGER ROD END NUT
a . Other than straightening a dented tool box and replacing a LOCK TWO SHORT SPRINGS LOCK NUTS
PLUNGER
damaged cover, other repairs are not practical. ROD_N_UT
ADJUSTING N~-T A
135. FOOTBOARDS.
a. Left Footboard Sidebar. The left footboard sidebar provides
"'
f&,! '' :::
RECOIL PLUNGER1PRING UNC:;ER SPRING
-~1~ •hl,t!
footboard . and clutch pedal mounting. Badly bent or broken parts SPRING SPRING GUIDE COLLARS RA I'D 310395
must be replaced. The footboard cover and the footboard hinges
can be replaced. Both footboards are interchangeable. figure J35- Saddle Spring Post, Disa ssembled
b. Right Footboard Sidebar . The right footboard sidebar pro-
vides footboard and brake pedal mounting. Badly bent or broken b. Saddle Post Adjustment. The spring saddle spring post is
parts must be replaced. correctly adjusted for the average weight rider when the distance
~rom end of plunger to adjusting nut is ll' o/to inches (fig. 136). To
mcrease spring compression, tum adjusting nut to the right. To
reduce spring compression, tum adjusting nut to the left.
• o I II l ,lt,•,t 1 t l• O,l l l ol t. l t
ADJUSTING NUT
l A I'D 110*9..
f igure J36-Soddle Spring Post Adjustment
200 201
! I
'
CHAPTER 14
ROAD TEST OF ENGINE, TRANSMISSION, AND CLUTCH
CHAPTER 13
CHASSIS PARTS AND EQUIPMENT (Cont'd) Section I
ENGINE
Section V
EQUIPMENT H :J. JNTROl>UCTIOI\.
a. After an engine has been overhauled. either top end or base,
138. A)1l\1UNIT ION CARRIER. i it ~ust be. adjuste~. operated and tested before installing in vehicle
a . Slightly bent or twisted ammunition carrier can be straightened. for 1mmed1ate serv1ce. The best method is to install engine in a test
B adly bent or broken carriers must be replaced. chassis and give it an actual road test. An engine fitted with new
pistons and / or rings must be given run-in consideration the first
500 miles the same as a new vehicle. Refer to TM 9-879.
139. GUN SCABBARD CARRIER.
b. Duration of Tt"st . To ensure normal operating temperatures
a. Slightly bent or twisted gun scabbard carrier can be straight- an d correct functioning of fuel system the overhauled engine must
ened. Badly ben t or broken carrier must be replaced. b e road tested between 5 and 10 miles.
140. LUGGAGE CA RRIER. 146. TEST CHASSIS.
a. Beyond straightening a slightly bent luggage carrier, further a . A v ehicle chassis must be available. complete in every detail,
repairs are not recommended. rea dy to accommodate either engine and / or transmission units for
test. Controls, brakes, tires, signal lights. electrical equipment. and
141. WINDSHIELD AND LEG SHIELDS. all fittings must be in good order for safe and satisfactory road test
a. Windshit"ld. Windshield pyralins and aprons can be replaced. p rocedu re.
Badly bent or broken frames and fittings must be repiaced.
b. Leg Shit"lds. If leg shields and brackets are slightly bent, they 147. LUBRICATION.
can be straightened and made serviceable. If badly damaged or a. N ewly overhauled engine will have one-half pint of engine oil
broken, replace. poured over the timing gears before gear case cover is installed. Oil
lines m~st be connected and oil must be present in tank and actually
reach 011 supply pump before operating newly overhauled engine.
142. SAFETY GUARDS.
a. Sa(ety guards are made of high quality, heat treated steel and . b . Obsern Actio n o f Rf'd S ig nal J.i~ht . After the ignition switch
when bent, but not kinked, they can be straightened cold. Do not 1s turned on. the red signal light in the switch panel should go on.
attempt safety guard repairs by welding or brazing methods. If re? sign al light fai.ls to go on, or fails to go off after engine is
runmn g, m ake followmg tests before proceeding with engine test.
{1) T EST S IGNAL LIGHT CIRCUIT. Test signal light circuit from
143. SADDLE BAGS.
switch to panel light by disconnecting wire at oil pressure switch
a. Saddle bags with ripped seams can be resewn and riveted. If and grounding on engine: then turn ignition switch on. L amp should
bag is badly tom, cut or otherwise damaged, replace it. light. If it does not light. check wiring and lamp. If lamp does not
light when connected to oil pressure switch with ignition on, replace
144. REAR VIEW MIRROR. oil pressure switch.
a. Other than replacement of rear view mirror bracket, &nd {2) S IGNAL L IGHT CONTINUES TO BuRN AI..TF.:R ENG INE Is Ot>t~~-t
bracket clamp, further repairs are not practicaL R ep lace broken or ATED ABOVE IDL ING SPEEDS.
badly damaged units. (a ) C h eck oil supply in tank. If red signal fails to go out Aft•·•
engine is warm, or after one minute of operation. fu rther check mu~t
be ~ad~ to locate trouble because indication points to faulty l'lll(llll'
lubr1catton system, or fault in signal light circuit. Elunlflnt•· 1111
signal ligh t system first as in ( 1) above.
(b) W ith oil pressure switch and signal syst('m wil inH 111 IL"'"'
order, yet light fails to go out after engine 1s o perating, inclu ,,, 11111 1111
troublt• 10 the oil supply pump. Replace pump.
202 203
ENGINE
I ~
\
e. Exceuive Smoke Issues from Exhaust and Oil Spray lslltH'" •

I
I 1111 luwd to stop: then back out needle valve 5 to 10 notches, or unt 11
from Gear Case Breathf'r Outlf'l. This is an indication that the rnRIIlt' fires regularly with retarded spark and throttle closed, or as
scavenger pump is not draining engine crankcase and returning 011 n< n1ly closed as it can be set and still have engine run at idling speed.
to tank. With engine running at idle speed, examine oil return in {o.l) ADJUST THROTTLE LEVER STOP SCREW. Adjust screw as may
tank. Remove tank oil cap and with a small ftashlight observe h<" necessary to make engine idle at proper speed with throttle in
whether or not oil is dripping from Ys-inch hole in oil return tube. fully closed posi~ion. Turning stop screw to the right makes engine
Hole is on underside of tube and is located just back of oil gage tdlc faster. Turnmg stop screw to the left makes engine idle slower.
rod tube. If observation is poor. place finger over hole and feel for NOTE : Do not idle engine at thP. slowest possible speed because an
pulsation of oil pressure. If oil does not return to tank. scavenger ~xtr~m~ly slow idli.n~ adjustment" causes hard engine starting. Chang-
pump is faulty. Should the crankcase breather valve be incorrectly mg 1dhng sp~ed w1th throttle stop screw is likely to change the low
timed, smoke will issue from the exhaust but not as noticeably as spe~d fuel mtxture to some extent; therefore. it will be necessary to
when scavenger pump is not working. See d below for this condition. agam. check and correct the low speed needle valve adjustment h {3)
d. Smoke Issues from Exhaust and Excessive Oil Condition of thts paragraph. Engine starting and all-around carburetion will
Exists Around Cylinder Ports (Where Exhaust Pipes Enter be better with low speed fuel adjustment slightly rich rather tha n
Cylinders). Engine scavenger pump and crankcase breather valve extremely lean.
are one unit. operated by worm gear located behind engine shaft
pinion gear. Although scavenger pump is not timed, the breather 149. IGNITIO!\.
valve sleeve which drives it must be timed to balance the engine a. Batlf'ry, Spark Advance, and Circuit Breaker. Battery in
lubricating system. If for any reason the scavenger pump unit is
te.s~ vehicle. m.u.st be at least one-half charged {1,200 sp gr) and
removed from engine base. the breather valve must be retimed wmng and 1gmtton must be in good order. Spark advance lever must
(within the gear case) when pump assembly is replaced. Incorrectly
advance and retard fully with operation of handlebar grip. Circuit
timed breather valve will force oil past piston rings, causing some breaker points must be adjusted to have 0.022-inch gap when open.
smoke besides forcing oil out through exhaust ports. causing excessive
oily condition around exhaust pipes where they enter cylinder ports. b. Spark Plugs. Spark plugs of questionable condition shou l~ be
replaced with new ones with No. 3 heat range. Gaps must be adjusted
e. Adjustment of OiJ Supply Pump. Adjustment of the oil feed
to between 0.025 and 0.030 inch.
pump is made by changing the tension of the oil pressure regulating
valve spring. Remove the cap screw to expose the adjusting screw. c. Observe Engine Operation for Excessive Spark Advance.
Correct adjustment is obtained when head of adjusting screw is When making road test of engine, observe for knocking at lower
Ya inch below top surface of pump body. Turning screw clockwise speeds and upon acceleration, due to excessively advanced spark.
increases the oil pressure : turning screw counterclockwise reduces the Also observe engine operating temperature that might be above
oil pressure. Refer to figure SO for nomenclature of oil feed pump, normal due to excessively advanced spark.
assembly. d. Observe Engine Operation for Retarded Spark. Accelerate
~ngine and listen .to exha u~t reports to detect retarded spark. If spark
IS retarded excess1vely, engme overheating will also result.
148. CARBURETJON.
a. Gasoline must be in tank and must reach carburetor bowl.
Throttle control must operate correctly with fully open and closed 150. NOISES.
positions of handlebar grip. With fuel valve open, observe for leaks a. Chassis Condition. It will be assumed that chassis will be in
in line connections and at carburetor bowl. good condition and that drive chains will be correctly adjusted so
b. Carburetor Adjustment. A carburetor that is badly out of that unusual noises from these sources will not be considered.
adjustment. or a new carburetor just installed. must be adjusted as . b. ~oises Caused by Excessive Clearan<'e. Piston slap, rod bear -
follows: Ing no1se and cam gear noise caused by excessive clearances or loose
(1) Tum the low speed needle valve .dl the way down (to right) fit can be d etected with engine idling or under load at low speeds.
(2) Back needle valve out (to left) about three full turns. W1th Noises of this type are generally metallic in sound. The engine should
needle valve in this position, engine will start, but mixture will proh be allowed to become warm enough to reach normal operating tern
perature before passing on piston slap.
ably be too rich.
(3) Start the engine. After choke lever has been moved to normnl c·. Thumping, Pounding Noise in Engine. Very close piston
open running position and engine is normally hot, correct adJUIItrnt'nt und ring fits , tight piston pins in rod bushings or twisted connc·ct1111(
1 uti 'I will co use pounding and thumping noise. If tappt•t r,uidt•H 111,.
of needle valve by turning needle valve down (to right) Ont' notch
at a time until mixture becomes so lean that engine missc:a and is 1111t luc·nted 111 correct position, thumping no1se in g<'or case wall 1c 11111
204 205
CHAPTER 14
d. Howling, Grinding Noise. If the timing gears are meshed too ROAD TEST OF ENGINE, TRANSMISSION, AND CLUTCH
close, a howling, grinding noise will result. If cam gear beanngs and (Cont'd)
flywheel mainshafts are not in alinement, a grinding noise results.
Section II
1
151. GENERAL PERFOIOtANt:E. •
TRANSMISSION AND CLUTCH
a. Test engine for all-around general performance, starting. ac-
celeration, smoothness of operation, and excessive overheating. Ob- I 52. INTRODUCTION.
serve for abnormal vibration which mil!ht indicate looseness of bolts
and nuts or flywheels out of true. C•1H:rve for sluggishness which u. A newly overhauled transmission and clutch unit must be
might be caused by lack of correct bearing tolerances. run-in or tested before installing in vehicle for immediate field serv-
ICe. Before testin~ transmission in test block or vehicle frame. make
b. Vehicle Service. Engine unit must be in such mechanical
sure that the case contains Y,. pint of engine oil. Starter crank
condition after road test as to render dependable field service, the
must be tri~d for full travel and disengagement of starter clutch at
same as a new eng~. end of starter stroke.
b. Length of Test. Bench block test of transmission should run
15 to 20 minutes. Vehicle test of transmission should run up to 5
miles for thorough check.
•
153. TEST CHASSIS.
a. The vehicle chassis used for engine testing can be used for
transmission test. All parts and units of test chassis must be in good
wor~ing condition for safe and satisfactory road test procedure.
Cham guards must be in place and chains must be correctly adjusted
before operating test vehicle.
154. GEAR SHIFTING.

~· Clutch control and gear shifter lever linkage must be correctly
adJusted (TM 9-879) before checking either the transmission or
clutch: Test for ease of gear shifting, low, through neutral, to second
and htgh. Gears must not clash in any selected position nor should
gears jump out of mesh with vehicle under load. Transmission must
be free from unusual noises.
155. CLUTCH ACTION.

. a. Observe action of clutch for smoothness of engagement, full
disengagement without dragging or grabbing and ability to put
~ehicle in motion. With clutch engaged and transmission in low gear,
tt. should not be possible to tum rear wheel by hand. and make clutch
ShJ;>. When idling engine with clutch disengaged, listen for unusual
notses coming from the clutch.
156. NOISES.
a. Transmission. Grinding noise in transmission indicates incor-
rect end play clearances, or improper assembly. Loose, rattling noise
m transmission indicates incorrect assembly.
b. Clutch. Loose, rattling noise in disengaged idling dutch may
hr coust'd by ball retainer plate having too much end play on thf'
Ht\Jd!l. R<'toiner spring rings may be broken or not tight III(HI1111t
rc·tnl nc.·r plotc.
207
206
SPECIAL TOOLS
Federal Mfgrs.
Special T-:>ol Stock No. No.
A WRENCH, SPOKE NIPPLE, FK :>NT WHEEL . 41-W-3339 HRO 120032-X
I TOOL, CARaURETOR CLEAN-UP, SET .•....... . .... 41 -T-30B1-45 HRD 12012-38
~ C REMOVER, CAM GEAR SHAFT BUSHING. . . . . .... 41-R-2372-20 HRD 11952-26
..
·-=--~
~~\~~ 8 ~~
,·~
I
~~,
D
D
I
REAMER, CAM GEAR SHAFT nMER DRIVE SHAFT
BUSHING . . . . . . . . . . ..................... .
TOOL, REPAIR, DRIVE CHAIN . . • . . . . • • . .....••.
41 -R-2265
4 1-T-3320
HRO 12133-37
HRO 12039-X
E c r REMOVER AND REPLACER, TRANSMISSION OIL SEAL 41 -T-2389-47 HRD 12735-42

0 GUIDE ASSEMBLY, CLUTCH GREASE, THROUGH OIL
~
K
(!) • (~ SEAL, 1941 MODEL. . . . .. .. .. .. ......... .. 41 -G-1 255 HRD 12747-41
-
L H- WRe«:H, CLUTCH HUB NUT ...•... •..• ...... . .. 41 -W -866-1 0 HRD 12745-41
~ IJ--=-;-· J- WRENCH, HEAD BOLT ...... .... ............ .. . . 41-W - 1525 HRD 12047-30A
1i11 ~ ~ e G
N
K- PULLER, CLUTCH HUB, MODEL 1941 ......•.... 41 -P-2905-90 HRD 12022·4 1
Ill
F
" 0 . L- WRENCH SPOKE NIPPLE, FRONT WHEEl ......... .
M- WRENCH, CYLINDER BASE NUT, TWIN ... ..•.. ....
41 -W -3339
41-W -872-10
HRO 12032 -X
HRD 12650-29
1
1
M N - PILOT, VALVE GUIDE, SMAll, 0.334 IN......... .. . 41 -P-4 12 HRO 12621 ·26
~
0 - REAMER, VALVE GUIDE STANDARD ............. . . 41 -R-2309-65 HRD 12623-26
~~c
0
0 1'-HOLDER, CUTTER HANDLE AND NUT. . . •.....• .... 41-H-2270 HRO 11898-X
p s Q - CUTTER, CLEARANCE, FOR 45 CU IN. TWINS ... .. . 41 -C-2822-30 HRO 11890-29
Q R I - PLATE, PISTON SQUARING, FOR All SINGLES AND
T ~ 45 CU IN. TWINS .... .. ........ . .....•......
S- LAP, BEARING, 1940 CRANKCASE.. ............. .
41-P- 1550-25
41 -L-203
HRO '2655-26
HRD 11954-40
u
T- ARBOR, CONNECTING ROD LAPPING FOR All l-INCH
CRANK PINS ............... ........ .... .... . 41 -A-337-10 HRO 11944-X
w U-GAGE, FLYWHEEL END PLAY, ALSO CHECK END
PLAY OF MAINSHAFT ON 45 CU IN. TRANSMIS-
SION ...•... , . .....•.... .. ..... . . ..••••. . . . . 41 -G- 198 HRD 11967-38
08 V- LIFTER, VALVE SPRING, HAND .......... .... .... .

W - TOOL, CONNECTING ROD CLAMPING ... •.•.• .•.•
4' · l·' 409
41 ·T-3091
HRD 12053-30
HRO 12058-X
AB
X- WRENCH, WHEEL LUG ........•....... . ...•.... 41 -W -3 832 HRO 12025-35
AC AD Y-STAND, FLYWHEEL TRUING, UNIVERSAL TYPE ..... . 41-S-4970 HRD 11962-X

%- TAP, HANDLEBAR END . ........ ...... .. ........ . 41-T-1026 HRD 12043-36
AI- PULLER, TAPPET, GUIDE ........................ . 41 -P-2956 HRO 11960-38
AC- PULLER, BEARING AND GEAR . ........ . . . ....... . 41 -P-2 903 HRO 11849-X
·---=-- AK AD- WRENCH, MANIFOLD .. .... .. .......... .... .... . 41-W- 1570-10 HRD 12003-X
AG AI- REAMER, OILER DRIVE SHAFT AND PIN SHAFT BUSH·

lNG, 74 CU IN. PIN SHAFT AND 45 CU IN. OILER
SHAFT DRIVE. .....•...... . . ........ ... ...... 41 -R-2303 HRO 12132-36
RA I'D 310410
Af- TOOL, LOCK RING ., .......................... . 41-T-3260 HRD 12052-32
figure J37 -Special Tools HRD 12067-42
AG- JIG, REAR SPROCKET RIVETING ... . . . .......... . 41 -J-373
AM- WRENCH, TAPPET AND VALVE COVER ........... . 41-W -3 617 HRO 11 806-31
AJ REAMER, PINION SHAFT BUSHING, ...... . . ...... . 41-R-2 304 HRD 12135 37
AI( TOOL, PISTON PIN BUSHING ................... . 41-T-3305 HRD 120.)7 X
lA I'D J1041 04
Legend lor figure J37-Speclal Tools

208 209
REFERENCES
CHAPTER 15 I'll HI JC \TIOI'S I ~DEXES.

I lu following publications indcxts should be consulted frequently
SPECIAL TOOLS
r... hdt st changes to or revisions of the publications given in this list
157. DESCRIPTI ON AND DATA. nf rt ft n net:s and for new publications relating to materiel covered
In tltt'> manual :
a . Tht tools illustrated in this chapter are used in maintaining
the vehtclc. Rcf<.r to figure 137. lntroductton to Ordnance Catalog (explains SNL
h . Th(• list in figure 37 is for information only. It is not to be used system) ASF Cat.
as a basis for requisition. ORD-1 IOC
Ordnance publications for supply index (index to
SNL's) . ..
' . . . .. ASF Cat.
ORD-2 OPSI
Index to ordnance publications (lists FM's, TM's,
- TC's and TB's of interest to Ordnance personnel,
'
I' M W Q's, OPSR's, BSD, S of SR's, OSSC's and
O F SB 's. Includes alphabetical listing of Ord-
nance major items with publication!> pertaining
thereto) . . . . .. . . ... O F SB 1-1
List of publications for training (lists MR's. MTP's,
T / BA's, T I A's, and FM's, TM's, and TR's con-
cerning training) . . .. FM 21-6
List of training films, film strips and film bulletins
(lists TF's, FS's, and FB's by serial number and
subject) F M 21-7
Military training aids (lists graphic training aids,
models, devices, and displays) FM 21-8
ST.~'IDARD 1\0\l ENCLATUHE LISTS.

Motorcycle, chain drive (Harley-Davidson) SNL G -523
Cleaning, preserving and lubricating materials, re-
coil fluids, special oils, a nd miscellaneous related
items . .. SNL K -1
Soldering, brazing, and w elding materials, gases,
and related items . .. S N L K -2
Tools, maintenance, for the repair of automotive
vehicles . SNL G 27
Tool sets-motor transport SNL N I q
Tool sets for ordnance service command, automo-
tive shops SNL N .10
Cu11 c nt Sl'\ndard N omt•ncloture Lists art listed above
-
. 2 11
210 - -
•. .
I
INDEX
A P'a;e No ,
EXPLANATORY PUBLICATIONS. All "" 111< nt disassembly , 91
'hi I h 142 preliminary in structions. 91
llywhrrl assembly in crankcase repair .. 94
Fundamental Principles.
&numbly 77 specificat ions for linker model
M ilitary motor vehicles . . . . . . . . . . .. . . . . . . AR 850-15 lu>nt hub . ..... 184 M88 97
•~•u hub . .
. . . . 183 Carburetor and intake pipe
Automotive electricity . . . . . . . . . . . . . . . . . . . . TM 10-580 rr11r wheel brake 171 adjustment ..... 37
•pnrk plugs 106
Electric fundamentals . . . . - . . . .. . . . . . . . . . . . . . . TM 10-455 installation 33
A1r dcoaners and fittings, description, removal . . . . . . . . . . . . . . . . 10
The motor vehicle • • • • • • • • • • • • • • • • • • • 0 • •
TM 10-510 < lrunmg. mspection, repair, asscm-
Chain guards ... 198
hl y, and disassembly . . . . 99
Chassis. body, and trailer units . . . - . . . . . . . . . . . TM 10-550
Ahncmcnt
Chains. sprockets, wheels, and hubs
chains and sprockets. . . . . . . . . . 186
t·onnecting rods and pistons .... 29
wheel hubs 179
Operation of Materiel. . . . . . . . 196
• • • • • • • • • • 0
frame wheel rims and spokes 176

handlebars and controls .. . . .. , . 194
Motorcycle, solo (Harley-Davidson Model WLA) TM 9-879 Ammunition carrier. . . , . , ...... . 202
Chassis parts and equipment
battery box, tool box and foot-
Armature
boards . .. . .. .. .. . ......... 200
Maintenance and Repair. fits and tolerances . . ....... . 125 '
equipment . . . . . ... .. ....... . 202
installat ion . , . . , . , ......... . 12 1
Automotive lubrication ... ..... . . ........ . . . . TM 10-540 Assembly
frame and tanks . ..... . ... . . , . . 196
mudguards, chain guards, stands,
Motor transport inspections TM 10-545 carburetor . . . . . . .. , .. , , . , ... . 96
• • • 0 • • • • • • • • 0 • • • •
and skid plate . . . . . . . . . . . . . 198
circuit breaker . . . . . . . . . . ... . 104
Tire repair and retread . . . . . . . . . . . . . . . . . . . TM 9-1868 clutch. . . . . . .... ... , . . .. . 140
Circuit breaker (timer) (See under
Ignition system)
crankcase ........ , , .... . . ' ' 76
Cleaning, preserving, lubricating and welding cylinder . . . . . . . ...... , . . ... . l3 Cleaning, inspection, and repair
materials and similar items issued by the engtne ....... . . ... 79 carburetor . . . . . . . . . . . . . . . . 93
ordnance department ..................... . TM 9-850 front hub .. .
. . . . . . . . . 183 circuit breaker ....... , . . . . . . . . 104
. ..
generating system .. . . . . . . . 119 clutch . . . . . . . . . . . . . . . . . . . 138
Protection of Materiel. oil feed pump .
. . .. . . . . . 73 crankcase . . . ... 63
rear hub . • • • • • 182
0 • • •
flywheel assembly in crankcase
Explosives and demolitions • • • • • 0 • • • • • • 0 • • • • • •
FM 5-25 rear wheel brake . . . . . . . . 170, 174 assembly . . 77
transmission ...... .. 156 fork ................ . 191
Defense against chemical attack . . . . ....... . FM 21-40 front hub ....... . 183
FM 17 -59 B front wheel brake . . . . . . . . . . . . 173
Decontamination of armored force vehicles ... .
generating system ....... . 109
Battery box . . . . .. 200
Chemical decontamination, materials and equip- Bearing oil seal ring, installation in
oil feed pump .... :. . . . 72
ment • • • • • • ' • • • • • • • 0 • • 0 • • • TM 3-220 '
I engine . . 79
rear wheel brake . ..' . 168
' roller bearings and shafts .... 53
Blackout headlight, desc!iption . . . . 131
scavenger pump and crankcase
Storage and Shipment. Brakes
74
breather valve. . . . . . . . , .. . .. .
front wheel brake . . . . . , . . . . . . . 172
Registration of motor vehicles . ... . . . .. ... ... AR 850-10 spark plugs. . . . . . . ......... . 106
' rear wheel b rake . . . . . . . . 167
transmission . . . .. . .. . .' .' 150
Storage of motor vehicle equipment .......... . AR 850-18 . .
Breet her valve assembly, installa -
.
t10n m engme . . . . . . . . . . . ...... , 80 valve tappets and guides ..... . 71
Ordnance storage and shipment chart, group G - Brush and spring assemblies, wheel hubs . . . . . . .. . . . .. 179
wheel rims and spokes .. ... . , 177
Major Items . . . . . . . . . . . . . . . ............ . OSSC-G inspection . . .,.......... 118
Clutch
c adjustment . . . . , ... •••• 142
Cnrburetor assembly and installation 140
ntl JUSt ment .' ..... 204 cleaning and inspection IlK
IIUI"Illbly 96 description l ,l'o
' It 111111& nnd rnapectron . .. 93 fill and tolerance• 14:1
l13
212
INDEX
C-Cont'd Pa ge No. F Cont'd hgo No. H Poge No
Clutch-Cont'd Disassembly 1 lvwlo••l H andleba rs and contcols
removal and disassembly . . . . . 137 carburetor . . . . . . . . . . . . . . . . . . . 91 ruarooolllv 58 ahnernent 194
road test .
. . . 207 circuit breaker ............... . 101 '"""'VIII from c ran k pm 51 description I 94
Clutch gear, mstallation ... 157 clutch . . . . . . ....... . . 137 I rl~ljlll 54 rep81r 195
cylinder 15 I tl11111l 61 H om and li ght ing system
Connecting rod bearings, inspection • • • - • • • • • • - • 0 0 • • • •
front hub . . . ........... . 183 I o>Ot l~>ilrds • 200 h orn and hghts JJ I
for wear .. 12 0 • • • 0
swttches and instrument panel 126

Connecting rod bushing (upper end} front wheel brake . . ...... . 172 l otrk
generating system . . . . . . . . . . 107 tlncnption 191 I
fits and tolerances . .. . 41
oil feed pump . . . . . . . . . . . . . . . 72 ftame head bearings 193 lenition light switch
fitting to piston pin ......... .. . 27
onspection 191
Crank pin rear wheel brake ..... . . . . . . . 167 assembly 129
tteering damper . . . • . 193 disa ssembly 126
fitting . . .. 54 scavenger pump and crankcase
•trllightening , . . , .. 193 inspection of parts
. . . . . . . . . 56
12 9
installation in flywheel breather valve. . ............ . 74
l<11ome and tanks Ignition system
transmission . . . . . . . . . . . . . . . ... 147
Crankcases
assembly. . . . ................ . 76 wheel hubs .. . . . . . . . .. . . . . . . 179
nlinement . . . . . . . .. . . 196 circuit breaker
description . . .. . . . .. . . .... 196 assembly 104
cleaning and inspection , , , . , . , .. 63 cleaning and inspection . 104
E tanks ._ . . .. .. , ' ' 197
disassembly .......... .. ... ... . 48 disassembly . . .... 101
'
64 Engine Front marker light, description .. 132
repa1r . . .. ... .. . .. . .... .
repa1r . . . . . . .. ... 104
Cylinder heads, installation .. . ... . 34 assembly. . . . . . . . . . . . . . . . . . 79 Front wheel brake
deS(;ription I0I
cleaning, inspection and repair of assembly and installation ..... . 174
Cylinders and piston assemblies ignition coil cable replacement 105
crankcase assemblies and gear cleaning and inspection . 173
assembly. . . . . . . , .. 23 spark plug cleaning and adjust-
cleaning and inspection ... , .... 15 case cover . . . . . . . . . . . , . . . 63 description I 72
ment . 106
disassembly . . . . . . . . . • .. 15 description. . ....... ... 7 removal and disassembly . . 172
Inspection (See Cleaning, inspec-
installation • 0 .... ..
• • • • .. 33
disassembly, cleaning and inspec·
tion; fitting crank pin and main-
repatr .... 174
tiOn, and repair)
removal Fuel, intake, and exhaust systems Instrument panel lamps . . . . . 130
shaft roller bearings, and assem· carburetor .. 91
mspectton o f connecting rod Intake pipe (manifold), description 99
bearing for wear .. 12 bly of flywheel assemblies 51 description . . . .. .. . 87
preliminary inst ructions 8 disassembly, cleaning, inspection, exhaust system .. 100 l
repair, assembly of cyhnders and fuel strainer and fuel supply valve 98 Lubrication of engine . 203
repatr . . . . 18
pistons and connecting rod aline- intake pipe, air cleaner, valve and M
meat. . SO fittings .... 99
D Magnetic switch, description 130
disassembly into subassemblies 43 F uel strainer, description 98 Mainshaft, fits and tolerances 166
Data
fits and tolerances 84 Mainshaft end play (transmission),
carburetor 97 Fuel supply valve, description and
engme
. • • 0 • • • • • • • 0 • •
7
fitting and assembly of fiywheel
repair .... 98 adjustment 157
transmtsston • . ... .. 146
and crankcase assembly . .
road test
16 Mainshaft roller bearings . . . . . 54
Description G Mudeuards 198
chains and sprockets .... 186
carburetion .. . . . . .. . . . .. . . 204 Gear case cover Muffier , description 100
•
chassis ... .. . .. . . . 203 cleaning, inspection and repair . 66 MWO and maJOr unit assembly
clutch . 135
ignition . . . . . . . . . . .. 205 mstallation in engine . .' 82 replacement record . . . . 6
exhaust system
fork
90
191
lubrication . . . . . . . . . .. . 203 removal .' . .. .. . 46 0
frame and tanks .
•
196
noises . .... . . . . . .. . .. . . 205
Generating system Oil feed pump, installation in engine 82
front wheel brake . 172 Exhaust pipes,. description .' 100 IISiembly and test . . . .. .. 119 Oil seal, replacement in transmission I 53
fuel and intake system ' . 87
F
deaning and inspection . 109 Overhaul of engine in vehicle
generating system 107 lle!l('riptoon , ..... 107 adjustment and tests ...... 36
handlebars and controls • 194 Field magnetic switch (generator), tl1111•aembly . . . .. . . 107 description and engine data. . . 7
ignition system .. 101 description .. 125 ht 1111d tolerances 125 disassembly, cleaning, inspection,
rear wheel brakes .. 167 Fits and tolerances &(I llrtnt or fitld magnetic switch . 125 repair, and assembly lS
switches and instrument panel 126 clutch .. 143 w•tullntoon of ernerator in engine 79 fits and tolerances 41
transmission 146
.
engme ..... . 41,1!4 or lnv ocl Ju•t mrnt and repatr 124 installation JJ
wheel hubs 179 generating system . - 125 tr I IIIII 119 removal of cylinder and poston
wheel rims and spokes . . 176 transmission •• 165 ll1111 1111l•l•ruo l ''" rtrr 202 assembly 8
214 215
p Pogo No.
Pogo No.
Pistons (and connectin& rods) Throttle shaft
alinement . . . . . . . . . . . . . . . . . . 29 installation.. . . . . • . . . . . . . . . . . . . 96
cleanine and inapection . . . . . . . . . 25 replacement . . . . . . . . . . . . . . . . . . . 94
deacription . . . . . . . . . . . . . . . . . . . 24 Timing gears
installation . . . . . . . . . . . . . . . . . . 28 . .
lilSpectlon . . . . . . . . . . . . . . . . . . . . 11
R installation in engine. . . . . . . . . . . 81
Rear wheel brake removal ...... ... ......... .. . 46
assembly an d installation . . . . . . . 170 Tool l:M:>x.. . . . . . . . . . . . . . . . . . . . . . . 200
cleanina: and inspection . . . . . . . . 168 Transmission
descri~tion . . . . . . . . . . . . . . . . . . . . 167 assembly ............. , . . . . . . . . 156
removal and disassembly... . . . . . 167
.
repasr . .......... 169
cleaning and inspection . . . . . . . . . 1SO
1 • • • • • • • • • • • •
description and data. . . . . . . . . . . . 146
Rear wh~l sprocket. . . . . . . . . . . . . . 186 disassembly . . . . . . . . . . . . . . . . . . . 147
Relay (a:enerator), adjustment and fits and tolerances . . . . . . . . . . . . . . 165
repaar . . .... . , . . . . . . . . . . . . . . . . . 124 .
repatr . . ...... .. ..... ... , . . . . 152
Road teat
. road test ... .. .... • .. , . , , . . . . . . 207
en(tne . . · · . ... , . . . . . . . . . . . . . . . 203 Truing wheels .......... .. ... .... 178
transmiasion .. , . . . . . . . . . . . . . . . . 207
vehicle , .......... , . . . . . . . . . . . 39 V --
i
s Valve tappets and guides
adjustment... . . . . . . . . . . . . . . . . . 36
j
Scavena:er pump, installation in

inspection and repair .......... . 71
encine ... 0 0
80 ••••••• - •••••• ' • • 0
removal· from engine. . . . . . . . • . . .

Service headlight description ..... . 131 47
Skid plate ...... , ........... .. . . . 199 w
Spark p lua:e, cleanine and adj ust· Wheel hubs
d . .
ment . . . . . . . . . . . . ...... . .. . 106 ~ption . .... ~- ............ . 179
Special toola ............... , ... . 210 front hub
Standa • • • • • • • •
198
• • • • • • 0 • • • • •• 0 • • 0 • assembly and adjustment ..... 183
St~rine eyatem cleaning, inspection and repair. 183
fork . . ........... . 191 . . . . .. . .. disasarmbly . ........... .... . 183
handlebar• and controla ..... . 194 rear hub
Stop lia:ht twitch, deacript ion ... . . . 130 assembly and adj ustment ..... 182
cleanine, inspection and repair . 179
T Wheel rims and spokes
Tailli&hte and atop lights description and data ..... . ..... . 176
blac kout etop lia:ht ... , ... , .. , .. 133 inspection . .. ................. . 177
service tailli&hU ... ·, ... , ..... , , 132 lace wheels .. .. ... .. .•. . , ..•... 178
Testing spoke replacement .. .. .. , ... , .. . 177
generatina: syatem ............. . 119 truing wheels . . .. .. .... ....... . 178
leaky valvea and worn piston rin&• 8 Windshield and lee shields . ...... . 202
2 16

45 Flathead Engine Overhaul Manual

Uploaded by

Copyright:

Available Formats

45 Flathead Engine Overhaul Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

45 Flathead Engine Overhaul Manual

Uploaded by

Copyright:

Available Formats

~-- -- -

Basic Drive Train

CHAPTER 2. OVERHAUL OF ENGINE IN

CHAPTER 3. ENGINE . .. . . . .. ... ... . . .. . .. . 19- 39 43- 86

CHAPTER 4. FUEL, INTAKE , AND EXHAUST

CHAPTER 10. BRAKES 93-102 167- 1 iS

CHAPTER 12. STEERING SYSTEM . . . . . . 118-125 191- 195

CHAPTER 15. SPECIAL TOOLS . 157 208-210

FRONT CYLit-.JDI k RA PO 3102 99

6. INSP ECTION OF CON!\ECTI!\G ROD BEARINGS J.'C•~t

8. CLEANING AND INSPF.CTJO:\ OF CYLINDERS AND

VALVE GUIDE REAMER

VALVE SPRING VALVE

SPRING Figure 8-Removing Carbon lrom Valve Guide with

ItA 1'0 310111

figure 12-lncreasing Valve Passage with Cutter (41-C-2822-30) ,

c. Valves. Valve face angle is 45 degrees for both intake and

figure 13-lnstolling Valve Stem Callar Keys, Using Lilter (41-L-1409)

10- CYLINDER ASSK'\HtLY.

Figure JS-Measuring Piston with Micrometer Calipers (41-C-307)

d. Release pressure on spring compressor to engage valve sprin&

PISTON PIN • PUSHING LOCK INTO PISTON PIN

. (3) . T~~n ~ngine in direction in which it runs until front cylinder

• Figure 24- Tightening Valve Spring Covers with

Figure 26 -Engine Mounting StanJ

c. Remove Accessories. Refer to TM 9·879 for removal instruc-

Figure 21-Removing Oil feed Pump . ""'· -·~

figure 29-Removing Scavenger Pump and Breather Valve Assembly

' l &' ' ' ' 'L' ~ER

Figure 32-Separating Crankcases

Figure 33-Separating Flywheels

(3) Separate flywheels by striking rim of right side flywheel with

25. FI'ITING CRANK PIN AND MAINSHAFT ROLLER

Figure 38-Assem&ling Flywheels It A PO 310321

Figure 39-ChecJcing Flywheel Rim Faces

FRONT CYLINDER THICKNESS GAGE

CLEANING , INSPECTION, AND REPAIR OF CRANKCASE

31. REPAffi OF GEAR CASE COVER

CASE BUSHING TIMER BUSHING

A-«EAMER PASSED THROUGH CRANK CASE BUSHING IN

1-REAM£11. ASSEMBLED TO REAM CASE COVEl TIMER BUSHING

33. INSPECfiO~ OF Tli\111\"G GEARS.

35. DISASSEMBLY, CLEANING, INSPECTION, REPAIR, AND

(2) REMOVE ROTARY BREATHER VALVE. After pump drive gear

Figure 53-Checking EnJ Play ol Flywheels in Crankcase with

b. Selecting and Fitting Thrust Collars. With right crankcase

. I Figure 56-Cross Section ol Catiwretor Floor Bowl

SHORT NEEDLE VALVE

Gf:\\'...-THROTTLE LEVER LIFT LEVER '=;:;;;,!;:::!/ SHAFT COLLAR

49. FUEL SUPPLY VALVE. 51. AIR CLEANER AND FITTINGS.

AL-\ '- _ \-AL BB AH AJ

AM --~ V :--:?i~ ~-AM

Figure 66-Generotor, Disos.semhled

A-DRIVE GEAR PIN R- NUT (2) AG-GASKET

9 -ARMATURE SPACER, 0.072 IN. THICK AF-REGULATING BRUSH HOLDER

DRIVE GEAR REGULATING

A- REMOVING DRIVE GEAR PIN 8-REMOVE ARMATURE END HUT.

FRAME END SCREWS

END CASTING REMOVED 1 .

Figure 68-R.emoving Generator Field Coils