Scribd
Upload
44 views2 pages

Manual Pol. 3000

1. This document summarizes the results of testing and maintenance performed on a Dräger Polytron 3000 device. 2. The tests evaluated the device configuration, maintenance parts, electrical safety, functions, and condition. Specific tests included checking the condition of the transmitter and sensor, calibration adjustments, signal transmission, and testing equipment. 3. The results were mostly marked as "OK", indicating the tests passed, with some values recorded such as mV readings for adjustment tests and a description provided in the report section.

Uploaded by

LUIS R
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
44 views2 pages

Manual Pol. 3000

1. This document summarizes the results of testing and maintenance performed on a Dräger Polytron 3000 device. 2. The tests evaluated the device configuration, maintenance parts, electrical safety, functions, and condition. Specific tests included checking the condition of the transmitter and sensor, calibration adjustments, signal transmission, and testing equipment. 3. The results were mostly marked as "OK", indicating the tests passed, with some values recorded such as mV readings for adjustment tests and a description provided in the report section.

Uploaded by

LUIS R
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Result Sheet Test instructions

Dräger Polytron 3000

Part number:

Location: Serial number:

Department: Cust. invent. no.:

Maintenance interval: Other / Delivery date:

Key

 / OK = OK
Applies to Test instructions Revision 3.0 + = Spare part used
! = Error / Report
/ = Accessory not available
- = Not applicable

Test Result
1 Device configuration
1.1 Show device information
1.2 Test gas values
 1.2.1 Target gas txt
 1.2.2 Test gas txt
 1.2.3 Test gas concentration txt
 1.2.4 Test gas unit txt
2 Maintenance parts
2.1 Maintenance intervals, overview - not applicable -
2.2 Maintenance parts by specified interval - not applica-
ble -
2.3 Maintenance parts as required
3 Electrical safety - not applicable -
4 Function and condition test
4.1 Device, general
4.1.1 Condition of device
 4.1.1.1 Check the condition of the transmitter OK
 4.1.1.2 Check the condition of the sensor OK
 4.1.2 Readiness (transmitter with display) OK
 4.1.3 Readiness (transmitter without display) OK
 4.1.4 Error code OK
4.2 Checking device functions
4.2.1 Adjustment preparation
4.2.2 Zero adjustment (transmitter with display)
 4.2.2.1 Zero adjustment (transmitter with display)
 4.2.2.2 Zero point set and adjustment applied. OK
4.2.3 Zero adjustment (transmitter without display)
 4.2.3.1 Zero adjustment (transmitter without display) mV
 4.2.3.2 Complete the zero adjustment OK
4.2.4 Sensitivity adjustment (transmitter with display)
 4.2.4.1 Sensitivity adjustment (transmitter with dis-
play)
 4.2.4.2 Sensitivity set and adjustment applied. OK
4.2.5 Sensitivity adjustment (transmitter without dis-
play)
 4.2.5.1 Sensitivity adjustment (transmitter without dis- mV
play)
 4.2.5.2 Sensitivity set and adjustment applied. OK
 4.2.6 Completing the adjustment OK
 4.2.7 Signal transmission at the evaluation unit OK
5 Tools and Test Equipment
5.1 Test equipment subject and not subject to mandato-
ry calibration
 5.1.1 Test equipment subject to mandatory calibration OK
5.1.2 Test equipment not subject to mandatory calibra-
tion

������������ ��������������������� �����


Report:

�����������������������������������������������������������

����� ����������������������������� �����������������������������������������������������������


������������������������������ �����������������������������������������������������������

������������ ��������������������� �����

You might also like