33 – ISOMETRIC DETAILING MODULE

**********************************************************************************
****
33,1 – Invalid paper size, use:- A0 –> A4 or AA –> AE
33,2 – ISO 1,2,3,4 only allowed
33,3 – AREA must be between 1 & 10
33,4 – TEST/PARAMETER n m : n OUT OF RANGE 0 – 9
33,5 – TEST/PARAMETER n m : m OUT OF RANGE 1 – 10
33,6 –  Unset
33,7 –  ON
33,8 –  OFF
33,9 – Precision Bores
33,10 – NOMINAL
33,11 – ACTUAL
33,12 – Charsize
33,13 – Invalid MessageAccuracy RADIAL #I – set to #I
33,14 – Invalid MessageAccuracy ITERATIONS #I – set to #I
33,15 – MessageAccuracy RADIAL
33,16 – MessageAccuracy ITERATIONS
33,17 –  UK
33,18 –  EUR
33,19 –  USA
33,20 – Date
33,21 –  (Dimension line standout distance)
33,22 – Dimensions
33,23 –  SUPPORT
33,24 –  LEFT
33,25 –  RIGHT
33,26 –  TOP
33,27 –  BOTTOM
33,28 – Margin
33,29 – DetailPlots
33,30 –  UP
33,31 –  DOWN
33,32 –  Direction
33,33 – Size
33,34 –  A#I
33,35 –  WIDTH
33,36 –  HEIGHT
33,37 – File AND DXF
33,38 – Frame
33,39 – Reserve
33,40 – FallingLines
33,41 –  DEGREES #I
33,42 –  RATIO #I
33,43 –  PERCENTAGE #I
33,44 –  GRADS #I
33,45 –  IMPERIAL #I
33,46 –  METRIC #I
33,47 – Isotype
33,48 –  COMBINED
33,49 –  ERECTION
33,50 –  FABRICATION
33,51 –  COMBINED ERECTION
33,52 –  COMBINED FABRICATION
33,53 –  ERECTION FABRICATION
33,54 –  SPOOL
33,55 –  NONE
33,56 –  DRWG
33,57 –  LINE
33,58 –  OVERALL
33,59 – Stack
33,60 – Detail plots secondary direction inconsistent with primary direction
33,61 –  DESCRIPTION
33,62 –  NODESCRIPTION
33,63 –  Code  #I
33,64 –  Lspacing  #I
33,65 –  OVERFLOW
33,66 –  DUMMY
33,67 –  #N  MULTIPLE
33,68 –  #N  SINGLE
33,69 – PlottingScale
33,70 – File
33,71 – Detail
33,72 – Revision
33,73 – File DXF
33,74 – PictureScale
33,75 –   #I  ALONG
33,76 –   #I  ACROSS
33,77 –   #I  PERCENT
33,78 –   #I  DRWGS
33,79 –  STRING
33,80 –  Supports
33,81 – Stacking
33,82 – ISO
33,83 –  BOX
33,84 – InsulationControl
33,85 – TracingControl
33,86 – Split
33,87 – Wastage AREA #I #I
33,88 – Weldnumbers
33,89 –  SMALL
33,90 –  MEDIUM
33,91 –  LARGE
33,92 – Weldtype
33,93 – SITE
33,94 – FABRICATION
33,95 – FORCESITE
33,96 – Diagnostics USER   #I
33,97 – Test #I  #I
33,98 – Dimdistance
33,99 – LooseFlangeAllowance
33,100 –  METIMP
33,101 –  IMPERIAL
33,102 –  METRIC
33,104 –  OFF ALL
33,105 –  EMPTY
33,106 – The DETAIL list :-
33,107 – ADD
33,108 – The REMOVE list :-
33,109 – REMOVE
33,110 – Invalid #N in ISODRAW return file
33,111 –   ISODRAFT MESSAGE FILE #N
33,112 –   ——– ——- —- ———–
33,113 – Title #I
33,114 – Value must be between 1 and 25
33,115 – Atext #I
33,116 – Value must be between 201 and 500
33,117 –  FT
33,118 – Delimiter
33,119 – SupportFile
33,120 – Paper Length #I
33,121 – PAPER LENGTH must be greater than ZERO
33,122 – VALUE must be an integer between 0 & 999
33,123 – SPEC REF #F gives material code (#N)  longer than max of #I characters
33,124 – VALUE between 1 & 20 only.
33,125 –  ATsymbol
33,126 –  COLON
33,127 –  PLUS
33,128 –  DOT
33,129 –  AND
33,130 – Diagnostics ISODAT    #I
33,131 – Diagnostics ISOPLOT   #I
33,132 –  NAME
33,133 – Instname
33,134 – Keys #I
33,135 – CLEAR UNSET
33,136 – CLEAR SET
33,137 – CuttingList
33,138 – Cutmarks
33,139 – MatlistFile
33,140 – MatControl
33,141 – MaterialList
33,142 – SpoolNumbers
33,143 – Underlayplot
33,144 – SymbolFile
33,145 – MessageFile
33,146 – TransferFile
33,147 – #F is not named
33,148 – PLOT FILENAME PREFIX has not been specified
33,149 –    SYSTEM ERROR Unable to scan pipe network Check data consistency report and flow
directions at bran…
33,150 – #F cannot be detailed – invalid element type
33,151 – Detail plotfile #N for #F not found
33,152 – #F cannot be removed – invalid element type
33,153 – Spool prefix from DB (attribute SPLP of #F) not found
33,154 –  Angles
33,155 – The DETAIL list is empty
33,156 – A fatal error has occurred in ISODRAW
33,157 – No pipes have been processed successfully
33,158 –  HV
33,159 – No branches in #F
33,160 – #F will not be detailed
33,161 – WARNING: Not all pipes have been processed
33,162 – HEAD & TAIL refs of #F refer to the same component  but head & tail positions are not close
enough to that component.
33,163 – HEAD & TAIL refs of #F refer to the same component  and head & tail positions are the
same.
33,164 – Component #F refers to a BRANCH ( #F ) which does not refer back to it.
33,165 – The HEAD of #F is connected to #F but the positions are not the same.
33,166 – The TAIL of #F is connected to #F but the positions are not the same.
33,167 – ELEMENT #F is not a piping component.
33,168 – Cannot find flange connected to PPOINT #I
33,169 – Cannot find end of WAFER at #F
33,170 –  Tags
33,171 –  TOTALLED
33,172 – No non-standard BOLT lengths for #F   LENGTH is #R
33,173 – No long enough non-standard BOLT lengths for #F
33,174 – No SPCOM for #F
33,175 – No BOLTS for #F at #F
33,176 – Invalid specref #F for #F or connected tube
33,177 – Cannot get DETAIL info. on #F
33,178 – Cannot get MATXT info. on #F
33,179 – Reference datum #F is un-named
33,180 – PWAST attribute from #F out of range  0.00 – 100.0
33,181 –  ITEMCODES
33,182 – #F connected to #F but not the other way round.
33,183 – #F not close enough to #F
33,184 – ARRIVE or LEAVE PPOINT greater than 4
33,185 – Multiway component #F has unexpected connection to #F
33,187 – Both legs of #F refer to the same BRANCH but positions are not the same.
33,188 – Both legs of #F refer to the same BRANCH and positions are the same.
33,189 – One leg of #F is connected to #F but the positions are not the same.
33,190 – No branch in #N is connected to an equipment nozzle
33,191 – Cannot open Message File : ERROR #I
33,192 – #F is not part of an equipment trim
33,193 – Message file not set
33,194 – Starting to detail #F
33,195 – #F is not in the network
33,196 – #F has already been detailed
33,197 –  PERPLOTFILE
33,198 – Warning: Grid Reference number for #F is unset – setting to 1
33,199 – Error in determining bolting for #F
33,200 – Unable to access PIPE SPEC #F
33,201 – Tagging
33,202 – FlowArrows
33,203 – Bad connection to #F
33,204 – ProjectNumber
33,205 – Ignore
33,206 – Mark
33,207 – PERSPOOL
33,208 – Weldid
33,209 –  with #I lines
33,210 – Paper size set to maximum of #I
33,211 –   Starting at #F
33,212 –     Off leg #F
33,213 –     Branch initialise #F
33,214 –  Offset
33,215 –  Angle  #R
33,216 –  WORL /*
33,217 – Axes
33,218 –  BRANCH
33,219 –  COMPONENT
33,220 –  Box
33,221 – Specbreak
33,222 –  FABRICATIONONLY
33,223 –  ERECTIONONLY
33,224 – Attaname
33,225 –  SPREF
33,226 –  DRAWING
33,227 – Tolerance
33,228 – Warning: Weldnumbers are Fromdb, but WMAX of #F is #I
33,229 – Please carry out weld-numbering check in DESIGN Spooling Application
33,231 – Cannot find BOLT SPCOM with BLTREF #F for #F
33,232 – Cannot open symbolfile #N for writing – opening readonly
33,233 –  READONLY
33,234 –  WRITE
33,235 – Warning: Material list has short itemcodes from more than one pipe spec
33,236 – Cannot allocate bolts
33,237 – System contains flanged components with both OLD and NEW bolting methods
33,238 – Pipe contains flanged components with both OLD and NEW bolting methods
33,239 – WARNING! The syntax “
33,240 –  ” will not be valid after PDMS 11 Use “
33,241 –  #R”
33,242 –  #R INCH”
33,243 – WARNING! – Weld box option not appropriate if weld numbering from           database –
Option ignored.
33,244 –  NOBOX
33,245 –  PIPEONLYSEPARATE
33,246 – default
33,247 – SKEY scale factor must be between #I and #I – value reset to 100%
33,248 – Bad format for SPCOM name #N – use ITEMCODE LENGTH LONG
33,249 – Mtexts
33,250 –  IGNORE
33,251 – Must specify SpoolNumbers Fromdb if PartNumbers Perspool Fromdb
33,252 – Unable to locate text ‘#N’ within itemcode
33,253 – Message 253
33,254 – Bolting
33,255 – Units
33,256 – METRIC lengths IMPERIAL bores
33,257 – Cannot mix spooling and pipe elements when detailing as a system
33,258 – Spooling element is not up to date
33,259 – Spooling element is not connected
33,260 – Spooling element is not up to date and is not connected
33,261 –  length description
33,262 – Internal error in detail list
33,263 –  length itemcode
33,264 –  APPEND
33,265 –  INSERT at ‘#N’
33,266 –  OVERWRITE
33,267 – #F – Illegal or Inaccessible Reference Datum point
33,268 – Reference datum #F – Orientation has been modified to prevent Doubleback Dimension
error
33,269 – Dimension omitted for Reference datum #F – Doubleback Dimension
33,270 – Branch end coordinates :-
33,271 –  AT Pipe
33,272 –  AT Nozz
33,273 –  AT Open
33,274 –  AT Clos
33,275 –  AT Vent
33,276 –  AT Dran
33,277 –  AT Misc
33,278 – Coords
33,279 – ISOPOST executable not defined in ISOPOST module entry
33,280 – ISOPOST module not defined in this project
33,281 – A fatal error has occurred in ISOPOST
33,282 –  FormatFilename
33,283 – Error opening ISOPOST workfile: #N
33,284 – Error writing ISOPOST workfile: #N
33,285 – Error opening cut pipe format file: #N
33,286 – No comparison date or Stamp set
33,287 – ContinuationSymbols
33,288 – Error – Reserved area is greater than picture height
33,289 – Boltfile not set
33,290 – Cannot set #I lines per page – less than #I
33,291 – No bolts found
33,292 – BoltFile
33,293 – Cannot open boltfile : ERROR #I
33,294 – Starting Bolt Report for #F
33,295 – Bolting OFF
33,296 – WORLD
33,297 – #F
33,298 – OPTIONS DEFAULT
33,299 – Illegal scale factor found for line flow arrow – default scale 8 used
33,300 –  Inline
33,301 – Itemcode
33,302 – Message 302
33,303 –  Length
33,304 – Valves
33,305 – Instruments
33,306 – Pcoms
33,307 – Traps
33,308 – Vents
33,309 – Filters
33,310 –  DEFAULT
33,311 –  Prefix
33,312 – CllengthFile
33,313 –  Insulation
33,314 –  from
33,315 –  String
33,316 –  Composite
33,317 –  Overall
33,318 – Elevation
33,319 –  Hangers OPPOSITE strings
33,320 –  Hangers ALONGSIDE strings
33,321 –  INTERSECTION
33,322 –  VERTICAL
33,323 –  VERTICAL and DIMENSIONS
33,324 – Message 324
33,325 –  SpecChanges
33,326 – CutpipelistFile
33,327 – Zerolengthskews
33,328 – Fallskews
33,329 –  THREEDBOX
33,330 –  TWODBOX
33,331 – Illegal HREF connection on #F
33,332 – Illegal TREF connection on #F
33,333 – Contents of symbol library #N :-
33,334 – Old symbol keys
33,335 – New symbol keys
33,336 –   #N
33,337 – No symbols defined in library #N
33,338 – Writable user defined symbol library file has not been specified
33,339 – Symbol key #N has been redefined in the symbol library
33,340 – Limit of #I user defined symbols exceeded
33,341 – Symbol key #N rejected
33,342 – Symbol #N has been added to the symbol library
33,343 – Error in updating symbol library
33,344 – New symbol library #N created
33,345 – Unable to create new symbol library #N
33,346 – Error reading symbol library #N
33,347 – Unable to locate key #N in symbol library
33,348 – Row number #I is outside the range 1-999
33,349 – Table number #I is outside the range 1-999
33,350 – Limit of #I user positional #N records exceeded
33,351 – Character height #D exceeds maximum limit of #D. #D used
33,352 – Symbol library file #N does not exist
33,353 – Additional weld numbers for #F will not be included on the isometric
33,354 – Charheight
33,355 –  CharHeight
33,356 –  Direction HORIZONTAL
33,357 –  Direction VERTICAL
33,358 –  Rows #I Columns #I
33,359 – Message 359
33,360 –  ALL
33,361 – Option number #I is outside the allowed range 1-140
33,362 – Option Debug #I   #I
33,363 – Balloon size #I is outside the allowed range 1-5
33,364 –  with balloon size #I
33,365 – The no of components :- #I is outside the allowed range 1-50
33,366 –  OFF #I
33,367 –  based on #N
33,368 – SPOOLNumbers must be positioned with table parameters
33,369 – TextPosition
33,370 – Text
33,371 – Skewbox
33,372 –  FULL
33,373 –  TRIANGLE Standout
33,374 –  TRIANGLE NSTD Standout
33,375 – Attribute
33,376 – SystemAttribute
33,377 – #F is a spool/field element and cannot be removed
33,378 – System table data cannot be displayed unless detailing a system
33,379 –  Hatch
33,380 – MARK DETAIL/REVISION options invalid when detailing spooling elements – command
ignored
33,381 – Change
33,382 –  DISTANCE
33,383 –  DIAMETER
33,384 –  Standard
33,385 –  Standard #R DIAMETER
33,386 – Bend radius outside allowable range 0 to 50 D
33,387 – Illegal value for bend radius
33,388 – Bendradius
33,389 –  LONG
33,390 –  SHORT
33,392 – Highlighting
33,393 – Tapping
33,394 –  Scale
33,395 – Colour
33,396 –  Coordinates
33,397 –  Rule
33,398 – Message 398
33,399 – Maximum of 20 nested PCOM tappings exceeded
33,400 – EquipmentNumbering
33,401 – Truncate
33,402 –  NOZZLE
33,403 –  LIST
33,404 –  NoPicture
33,407 – Warning – There is no standard spindle skey #N
33,408 – Plottingscale limits (50-100%) exceeded – reset to 100
33,409 –  Number #I
33,410 – Unable to extract data for UDA key: #I
33,411 – Message 411
33,412 – with Boxstyle
33,413 –  on
33,414 – STRAIGHT
33,415 – ANGLED
33,416 – ROUND
33,417 – TRIANGULAR
33,418 – DIAMOND
33,419 – Outcom Blank
33,420 – Outcom
33,421 – UDA #N ignored. Maximum number of 50 exceeded
33,422 – Tubesplits
33,423 –  of
33,424 – PERDRAWING
33,425 –  SUFFIX
33,426 –  SINGLE
33,427 –  SUFFIX  SINGLE
33,428 – Leglength
33,429 – Repeatability
33,430 – Returnfilename
33,431 –  ENDPREPARATIONS
33,432 – Pipe #N requires addition of split ATTA(s) by DESIGN macro
33,433 – Invalid #F detected in return file
33,434 – Invalid ISOTYPE for DETAIL SHEET. Detail ignored.
33,435 – Invalid ISOTYPE or SPOOLNUMBER option for DETAIL SPOOL. Detail ignored.
33,436 – System isometrics are not available for detail SHEET or detail SPOOL.
33,438 – Equipment trims are not available for detail SHEET or detail SPOOL.
33,439 –  Spool #N
33,440 –  Sheet #N
33,441 –  Sheet Single
33,442 – Message 442
33,443 – Message 443
33,444 – No such Cutback rule set
33,445 – Invalid ISOTYPE for REMOVE SHEET. Remove ignored.
33,446 – Invalid ISOTYPE or SPOOLNUMBER option for REMOVE SPOOL. Remove ignored.
33,447 – Unable to create split atta associated with #F
33,448 –  on threadedends
33,449 – Pipe contains split ATTA – Repeatability ON ignored
33,450 – Cutback
33,451 –  on all bend
33,452 –  with
33,453 – none
33,454 –  CRITICAL
33,455 –  CENTRELINE
33,456 –  STOPPING Branch Connections
33,457 – Overall dimensions are not available with ISOTYPE SPOOL
33,458 – Overall dimensions suppressed for ISOTYPE SPOOL
33,459 –  (Treated separately for different text after delimiters.)
33,460 –  (Ignore any text after delimiters.)
33,461 – Dtexts
33,462 – Invalid type #F for DETAIL SPOOL/SHEET. DETAIL ignored.
33,463 – Invalid type #F for REMOVE SPOOL/SHEET. REMOVE ignored.
33,464 – ONLY
33,465 –  ACROSS Branch Connections
33,466 –  XTEXT
33,467 –  YTEXT
33,468 –  ZTEXT
33,469 –  RTEXT
33,470 –  STEXT
33,471 –  TTEXT
33,472 – Detailing interrupted by user
33,473 – Overallskews
33,474 – Leglength set to minimum value of 6mm
33,475 –  SEPARATE
33,476 –  TOTAL
33,477 – Leglength set to maximum value of 18mm
33,478 – Cannot find flange connected to #H of #F
33,479 – Cannot allocate bolts for #F
33,481 – Error reading binary IDF
33,482 – Error writing to ASCII IDF
33,483 – Error formatting data for ASCII IDF
33,484 – Error writing binary IDF
33,485 – Error reading ASCII IDF format
33,486 – Error reading ASCII IDF
33,491 – Error extracting itemcode from #N of specref #F for #F or connected tube
33,492 – Error extracting itemcode from specref #F for #F or connected tube
33,493 – Error extracting itemcode from #N attribute of #F for bolt #F
33,494 – Error extracting itemcode from bolt #F
33,500 – Overlay number must be between 1 and #I
33,501 – Message 501
33,502 – Underlay file #N does not exist. Command ignored.
33,503 – Underlay filename is already on list. File name ignored.
33,504 – Processing transfer file #N
33,505 – Error in opening message file #N
33,506 – Error in opening workfile
33,507 – Error in opening transfer file
33,508 – Error at line #I of transfer file
33,509 – Unable to process transfer file #N – Command ignored.
33,510 – Refdimensions
33,511 – Specified UDA not available on #H elements
33,513 –  X
33,514 –  Y
33,515 –  Xoff
33,516 –  Yoff
33,517 –  Angle
33,518 – ContNotes
33,519 – PIPE
33,520 – DRWG
33,521 – BOTH
33,522 – Attribute #H of #F has no NAME – cannot set continuation drawing
33,523 – Attribute #H of #F not found or unset – no continuation drawing
33,524 – Descriptions
33,525 – JointNumbers
33,526 – SHIFTJIS
33,527 – EUC
33,528 – Character height #D is less than minimum of #D. #D used
33,529 – PartNumbers
33,530 – FROMDB
33,531 – GENERATED
33,532 – Cannot specify bend table if PartNumbers not from database
33,533 – Cannot specify bend table file if PartNumbers not from database
33,534 – Attribute data #N is too wide to fit into column width #I – truncated
33,535 – Preprocess must have value 1 to #I
33,536 – Postprocess must have value 1 to #I
33,537 – Preprocess
33,538 – Postprocess
33,539 –  ASCBIN
33,540 –  Fill
33,541 –  Heading
33,542 –  NoHeading
33,543 – AngleAccuracy must be 0 or 1 (max accuracy)
33,544 – Angle must be between 0 and 360 degrees.
33,545 – CAREA attribute unset, text “AREA”  written to Compipe MTO file.
33,546 – CompipeFile
33,547 – Compipe
33,548 – MTO PIPE
33,549 – MTO DRWG
33,550 – Itemcodes USER
33,551 – Itemcodes CLIENT
33,552 – Supports ON
33,553 – Supports OFF
33,554 – Descriptions SHORT
33,555 – Descriptions LONG
33,556 – WeldTableFile
33,557 – BendTableFile
33,558 – #N table is file only and no file has been specified
33,559 – Title block text is limited to #I characters, plus optional underscore
33,560 –  Partial
33,561 – Hatch spacing value is less than the minimum allowed. Default value used
33,562 – Hatch spacing value exceeds the maximum allowed. Now set to #I
33,563 – Partial hatching value is less than the minimum allowed. Default value used
33,564 – Partial hatching value exceeds the maximum allowed. Now set to #I
33,565 –  EXTENDED
33,566 – PTDIRFTUB
33,567 – Text positioning attribute #N for #F is invalid or unset
33,568 – The #N standout distance is the same as the #N standout distance
33,569 – No columns defined for #N table
33,570 – Text positioning attribute #N not valid for SYSTEM
33,571 – Sort attribute #N not included in weld table
33,572 – System
33,573 – Invalid column number. Must be between 1 and #I
33,574 – Invalid column width
33,575 – Fall AccuracyLevel must be 0, 1 or 2 (max accuracy)
33,576 – AngleAccuracy
33,577 –  AccuracyLevel
33,578 – FileOnly
33,579 –  AUTOMATIC
33,580 –  characters
33,581 – BendTable
33,582 – RevisionTable
33,583 – SystemTable
33,584 – WeldTable
33,585 – SortBy
33,586 –  FORWARDS
33,587 –  REVERSE
33,588 – Corner
33,589 – BL
33,590 – BR
33,591 – TL
33,592 – TR
33,593 –  Empty
33,594 –  Width
33,595 – Column width #I too small for title ‘#N’ – width set to #I
33,596 – ContWelds
33,597 – Cannot add columns to non-existent #N table
33,598 – Sort attribute #N number #I not included in weld table
33,599 – Column #I of #N table created – NoHeading Empty Width #I
33,600 –  Columns
33,601 – TableDefinition
33,602 – Column
33,603 –  with Width
33,604 – FROMSPCOM
33,605 – and
33,606 – Number of AppWare texts exceed maximum #I
33,607 – Part number (attribute #H) for #F not found
33,608 – Part number (attribute #H[#I]) for #F not found
33,609 – #F has invalid part number #I (attribute #H)
33,610 – #F has invalid part number #I (attribute #H[#I])
33,611 – Navigation error searching for bolts part number for #F
33,612 – Bolts part number for #F – #F is part of a different system
33,613 – Bolts for connection #F – #F excluded from isometric
33,615 – Text element #F STEXT #N does not convert to a valid pipe/branch name
33,616 – Cannot specify weld table if WeldNumbers not from database
33,617 – Cannot specify weld table file if WeldNumbers are not on
33,618 – Weld number (attribute WLDN) for #F not found
33,619 – #F has invalid weld number #I (attribute WLDN or AWELDS)
33,620 – Weld attribute #N for #F is invalid or unset
33,621 – Logical
33,622 –  TRUE
33,623 –  FALSE
33,624 – #F is not named – cannot detail drawing
33,625 – Revision attribute :REV0 is not included in revision table
33,626 – Revision table attribute :REV0 for #F not found or unset
33,627 – Invalid attribute #H for revision table – must be a UDA
33,628 – Starting to detail SYSTEM #N
33,629 – Starting to detail EQUIPMENT TRIM #N
33,630 – System #N will not be detailed.
33,631 – Equipment trim #N will not be detailed.
33,632 – No bolt report possible for #F
33,633 – Detailing #F
33,634 – ShortCode
33,635 – PipenameDelimiter
33,636 –  Prefix
33,637 –  Suffix
33,638 – System table attribute #N for #F is invalid or unset
33,639 – ShortCode is not a valid option for #N table
33,640 – ShortCode has not been defined for system table
33,641 – Compipe option cannot be set for #N isometrics
33,642 – Cannot detail a branch with Compipe option
33,643 – AppWareText
33,644 – unset
33,645 – Invalid AppWareText keyword text
33,646 – LAST MEMBER
33,647 – NEW ATTA
33,648 –  BEFORE
33,649 – CONN TO PT
33,650 – CONN TO PH
33,651 – PARTNUMBER
33,652 – DESCRIPTION
33,653 – BORE
33,654 – ITEMCODE
33,655 – QUANTITY
33,656 – REMARKS
33,657 – OTHER
33,658 – CONN TO NEXT
33,659 – CONN TO PREV
33,660 – POS DIST
33,661 –  FROM PL OF PREV
33,662 –  ATTY XXXX SELECT ORI
33,663 – Cannot write a DESIGN macro for split ATTA in #F
33,664 – DESIGN macro written by ISODRAFT for db
33,665 – Writing a DESIGN macro for db #N
33,666 – DESIGN macro file #N created
33,667 – Cannot create DESIGN macro #N
33,672 – Maximum number of DESIGN macros is #I
33,673 – Cannot create DESIGN macro
33,675 – Adding Split ATTA in
33,676 – Branch is in db #N
33,677 – Line Thickness must be between 1 and 10; default is 3
33,678 – LineThickness
33,679 – #H UDA
33,680 – Cannot write a DESIGN macro to change attributes of #F
33,681 – Changing attributes in
33,682 – REV #I
33,683 – DETA TRUE
33,684 – COMPONENT
33,685 – Outcom Triplets
33,686 – Outcom BlankTriplets
33,687 – Cannot define material list table if PartNumbers not from database
33,688 – Linespacing limits (70-200%) exceeded – reset to 100
33,689 – Cannot specify bend table with Bendradius OFF
33,690 – Bltrefs #F and #F have inconsistent number or diameter of bolts
33,691 – ContJoints
33,692 – Module executable #N does not exist
33,693 – ISODRAW executable not defined in ISODRAW module entry
33,694 – ISODRAW module not defined in this project
33,695 – ISODRAW Symbolfile #N does not exist
33,696 – ISODRAW symbolfile not defined in ISODRAW module entry
33,697 – No plotfiles were produced
33,698 – No status information available for isodraw run
33,699 – No sheet information found
33,700 – No status flag for drawing
33,701 – Plotfile #I does not exist
33,702 – Drawing #I does not exist
33,703 – Failed
33,704 – Plotted
33,705 – Plot
33,706 – DXF
33,707 – Both
33,708 – Isodraw did not run – or failed.
33,709 – Symbol keys defined in DRAFT symbol file are:-
33,710 – Skey
33,711 –  based on
33,712 – No symbol file has been defined
33,713 – No symbol definitions exist in the symbol file
33,714 – To modify the contents of a new style symbol file – use the DRAFT module
33,715 – No parameterised plotfiles have been defined.
33,716 – Parameterised plotfile names are:-
33,717 – ATTRIBUTE
33,718 – HEIGHT
33,719 –  ANGLE
33,720 – Number of Parameterised attributes is #I
33,721 – PLOTDETAILDATA
33,722 – Character height must be > 0
33,723 –  #I
33,724 – HYPERPLANT
33,725 – DEBUG
33,726 – X value must be > 0
33,727 – Y value must be > 0
33,728 – Angle must be in the range -180 to +180
33,729 – No parameters have been defined
33,730 – Parameterised Attributes are:-
33,731 – Parameter #I does not exist
33,732 –  RelativeTo
33,733 –  Boxed
33,734 – Data for Detail plotfile #N not found
33,735 – Detailplots are undefined
33,736 – MANUAL
33,737 – When redefining spindle keys a new SKEY must be given
33,738 – Environment variable PDMSWK unset
33,739 – Error opening Cut-Piece report workfile: #N
33,740 – Unable to write to formatted Cut-Piece report file
33,741 – Unable to open formatted Cut-Piece report file
33,742 – Unbalanced % characters in Cut-Piece file
33,743 – Environment variable unset in Cut-Piece file
33,744 – Insufficient values found in Cut-Piece file
33,745 – Unable to open Cut-Piece csv file for reading
33,746 – Unable to open formatted Cut-Piece file for reading
33,747 – Unable to open Cut-Piece appware data file for writing
33,748 – Unable to write to Cut-Piece appware data file
33,749 – A fatal error has occurred when producing the Cut-Piece report
33,750 – #F has already been added to the detail list
33,751 – #F has not been added to the detail list
33,752 – #F has invalid reference to associated RWELD element
33,753 – Warning: Numbers are Fromdb, but #H of #F is #I                 Please carry out numbering
checks in SPOOLER
33,754 – Warning: Pulled Bend number for #F is invalid or unset
33,755 – PBendNumbers
33,756 – Warning: Joint number for #F is invalid or unset
33,757 – Pulled bend numbering only possible when detailing SPOOLER elements                 –
PBendNumbers option ignored
33,758 – There is no standard skey #N
33,759 – Cannot overwrite standard SKEY #N
33,760 – SKEY #N is not user-definable
33,761 – There is no base skey #N for component of type #H
33,762 – Cannot have #H components based on generic type of #H
33,763 –  AWELDS
33,764 –  BALLOONS #I
33,765 –  ELLIPSE
33,766 – Attexts none
33,767 – Attexts
33,768 – Warning: some Attexts have been truncated
33,769 –  in Millimetres
33,770 –  in Metres
33,771 – Warning: Defined material list table when PartNumbers are not from database
33,772 – Cannot Exit from Isodraft
33,773 –  PARTNUMBER
33,774 – ContSheets

100mm).