Material Safety Data Sheet

MSDS
SECTION 1 PRODUCT IDENTIFICATION
Product name : REXCO 18 Specialist Contact Cleaner
Cross reference : Electric Contact Cleaner, Solvent Degreaser, Etc
Manufacture : PT. ALTAMA SURYA ANUGERAH
Address : Jl. Bandengan Utara 85A No. 4
Penjaringan-Penjaringan
JAKARTA UTARA 14440 – DKI JAKARTA RAYA
INDONESIA
Phone number : +62 21 6680180
Fax : +62 21 6691777

SECTION 2 HAZARDOUS INGREDIENTS

Chemical name :CAS Number Percent TLV
2-Methyl Pentane :107-83-5 >50 300 ppm
Hexanes :110-54-3 <20 50 ppm
Alkanes C3-4 :68475-59-2 30% 100 ppm

SECTION 3 HAZARDS IDENTIFICATION

Health Hazards May be harmful if inhaled and/or ingested. Avoid breathing of vapors. May
cause skin irritation. High Vapor may be irritating to eyes and respiratory tract.
See section 11 for further information
Physical Hazards Combustible liquid. Liquid or vapor may ignite. Keep away from all sources of
ignition

IMO - International Maritime Organization

Flammable liquid
UN no 1208

SECTION 4 FIRST AID MEASURES

Routes of exposure and effects of overexposure:
Inhalation :May cause dizziness and nausea .
Skin Contact :May cause light irritation for sensitive skin.
Ingestion :Do not ingest.
Emergency First Aid Procedures:
Eye contact :Irritant to eye, flush immediately with large amount of water for 15
minute, get medical attention.
Skin contact :May cause irritant to sensitive skin, rinse thoroughly with water,
remove contaminated clothing and shoes immediately. if irritant occur,
get medical attention.
Inhalation :Remove to fresh air.
Ingestion :Call physician immediately, Don’t give anything to mouth
to unconscious person.

1
 Material Safety Data Sheet
MSDS
SECTION 5 FIRE FIGHTING MEASURES
EXTINGUISHING MEDIA: Foam, water spray (fog), dry chemical, and carbon dioxide. Water spray can
be used to cool and protect containers exposed to heat and flame.
UNUSUAL FIRE AND EXPLOSION HAZARDS: Combustible liquid. Can form combustible mixtures at
temperatures at / or above flashpoint. Materials can accumulate static charges, which can cause an
incendiary electrical discharge. Toxic fumes or vapors may evolve on burning. This liquid is volatile and
gives off invisible vapors. Vapors are heavier than air and may travel along the ground or be moved by
ventilation and ignited by heat, pilot lights or other flames and ignition sources at locations distant from
material handling point. Container may rupture on heating.

SPECIFIC METHODS/ PROTECTION OF FIREFIGHTERS: Do not enter confined fire space without full
Bunker gear (helmet with face shield, bunker coats, gloves and rubber boots), including a positive-pressure
NIOSH approved self-contained breathing apparatus. Isolate “fuel” supply from fire. Avoid spraying water
directly into storage containers due to danger of boil over.

DECOMPOSITION PRODUCTS UNDER FIRE CONDITIONS: Thermal decomposition products are

highly dependent on the combustion conditions. A complex mixture of airborne solid, liquid, particulates
and gases will evolve when this material undergoes combustion. Fumes, smoke, carbon monoxide and
other products of incomplete combustion may be found upon combustion.

SECTION 6 ACCIDENTAL REALEASE MEASURES

PERSONAL PRECAUTIONS: Personnel protective equipment must be worn (See Section 8). Minimize
contact with skin and clothing.
ENVIRONMENTAL PRECAUTIONS: Keep product out of sewers and watercourses by diking or
impounding. Advise authorities if product has entered or may enter sewers, watercourses, or extensive land
areas. Warn occupants and shipping in surrounding and downwind areas of fire and explosion hazard and
request all to stay clear. Assure conformity with applicable governmental regulations.
METHODS FOR CLEANING UP: Ventilate spill area if in confined or poorly ventilated area. Pick up free
liquid with explosion proof or hand pump for recycle and/or disposal. Residual material can be absorbed on
inert material. Do not use combustible materials such as sawdust.

SECTION 7 HANDLINGAND STORAGE

TECHNICAL MEASURES: Keep containers closed when not in use. Do not store near heat, sparks, flame
or strong oxidants.
PREVENTION OF USER EXPOSURE: Avoid contact with eyes. Avoid prolonged or repeated contact
with skin and clothing. Wash thoroughly after handling. Remove contaminated clothing and launder before
reuse.
PREVENTION OF FIRE AND EXPLOSION: Refer to Section 5.
PRECAUTIONS: Use product with caution around heat, sparks, pilot lights, static electricity and open
flame.
SAFE HANDLING ADVICE: Refer to Section 10.
STORAGE
TECHNICAL MEASURES: Keep containers closed when not in use. Do not store near heat, sparks, flame
or strong oxidants.
STORAGE CONDITIONS: Store in a cool, dry ventilated area. Keep containers tightly closed and upright
when not in use.
INCOMPATIBLE PRODUCTS: Refer to Section 10.
PACKAGING MATERIALS: The original Prolong container is the recommended storage material for this
product.

2
 Material Safety Data Sheet
MSDS

SECTION 8 EXPOSURE CONTROLS/PERSONAL PROTECTION

ENGINEERING MEASURES
CONTROL PARAMETERS: The use of local exhaust ventilation is recommended to control process
emissions near source. Laboratory samples should be stored and handled in lab hood. Provide mechanical
ventilation of confined spaces. No smoking. Keep away from flame or other ignition sources.
PERSONAL PROTECTIVE EQUIPMENT
RESPIRATORY PROTECTION: Use NIOSH/MSHA approved full face respirator with a combination
organic vapor and IGH efficiency filter cartridge if the recommended exposure limit is exceeded. Use self-
contained breathing apparatus for entry into confined space, poorly ventilated areas and for large spill
clean-up sites.
HAND PROTECTION: Use chemical-resistant gloves to avoid prolonged or repeated skin contact.
EYE PROTECTION: Wear chemical splash goggles with side shields or face shield.
SKIN AND BODY PROTECTION: Long sleeve shirt is recommended. Use of chemical-resistant apron or
other impervious clothing recommended. Chemically resistant boots are also recommended. Launder
clothing before reuse.
HYGIENE MEASURES: Minimize breathing vapor, mist or fumes. Avoid prolonged or repeated contact
with skin. Remove contaminated clothing; launder or dry-clean before reuse. Remove contaminated shoes
and thoroughly clean before reuse; discard if oil-soaked. Cleanse skin thoroughly after contact, before
breaks and meals, and at end of work period.

SECTION 9 PHYSICAL DATA

Boiling Point : 62ºC
Flash Point : <25ºC
Solubility in water : Not Soluble
Vapor density : 3.28 (air =1)
Appearance & odor : light transparent, solvent odor
Spec Gravity : 0.6629
pH N/A

SECTION 10 REACTIVITY DATA

Stability :Stable as long as container is tightly close and put in dry area
Incompatibility :Avoid contact with strong oxidizing material, avoid
contact with heat sources.
Hazardous Decomposition product :Oxides of carbon.
Hazardous polymerization :Will not occur.

SECTION 11 TOXICOLOGICAL INFORMATION

PRIMARY ROUTES OF ENTRY OR EXPOSURE: Skin absorption, eye contact, inhalation and ingestion.
INHALATION: Vapor concentrations above recommended exposure limits are irritating to the eyes and
respiratory tract. May cause headaches and dizziness, are anesthetic and may have other central nervous
system effects, including death based on data from components or similar materials.
SKIN: Slightly irritating to the skin. Prolonged and repeated contact may result in various skin disorders
such as dermatitis. Skin contact may aggravate existing dermatitis condition based on data from
components or similar products.
EYE: May cause eye irritation based on data from components or similar products.

3
 Material Safety Data Sheet
MSDS
INGESTION: Ingestion of material may result in vomiting; Aspiration (breathing of vomitus into the
lungs) must be avoided as even small quantities may result in aspiration pneumonitis. Ingestion may cause
irritation of the gastrointestinal lining, nausea, vomiting, diarrhea and abdominal pain.
ACUTE TOXICITY: Pre-existing skin and respiratory disorders may be aggravated by exposure.

SECTION 12 ECOLOGICAL INFORMATION

STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED: Ventilate and remove with inert
absorbent. Pick up large spill with vacuum tracks or pump. Absorb small spills/leaks with oil absorbent.
Follow local and government regulation regarding disposal.

SECTION 13 DISPOSAL CONSIDERATIONS

WASTE DISPOSAL METHODS: Dispose in an environmentally safe manner and in accordance with
governmental regulations.

SECTION 14 TRANSPORTATION INFORMATION

DOT CLASSIFICATION: NA1993,NOS (AROMATIC HYDROCARBON),PGIII,3 COMBUSTIBLE
LIQUID
DOT BULK SHIPPING CLASSIFICATION: NA1993,NOS (AROMATIC HYDROCARBON),PGIII,3
IMDG CODE: NA1993,NOS (AROMATIC HYDROCARBON),PGIII,3
TRANSPORTATION INCIDENT INFORMATION: For further information relative to spills resulting
from transportation incidents, refer to latest Department of Transportation Emergency Response Guidebook
for Hazardous Materials Incidents.

SECTION 15 REGULATORY INFORMATION

THE FOLLOWING INFORMATION MAY BE USEFUL IN COMPLYING WITH VARIOUS STATE
AND FEDERAL LAWS AND REGULATIONS UNDER VARIOUS ENVIRONMENTAL STATUES:
THRESHOLD PLANNING QUANTITY (TPQ), EPA REGULATION 40 CFR 355 (SARA SECTIONS
301-304): No TPQ for product or any constituent greater than 1% or 0.1% (carcinogen) for SARA Section
302.
TOXIC CHEMICAL RELEASE REPORTING, EPA REGULATION 40 CFR 372 (SARA SECTION
313): This product contains the following substances subject to the reporting requirements of SARA III
Section 313 1986 and 40
TSCA INVENTORY: All components are listed on the TSCA inventory.
IMO: CLASS 3: Flammable liquid
UN no: 1208
NOTE: State and local regulatory requirements may be more restrictive or otherwise different from federal
regulations. Consult state and local regulations regarding other regulatory requirements.

SECTION 16 OTHER INFORMATION

The information and recommendation herein are, to the best of our knowledge and belief, accurate and
reliable as of the date issued. PT. ALTAMA SURYA ANUGERAH does not warrant or guarantee their
accuracy or reliability, and shall not be liable for any loss or damage arising out of the use thereof. The
information and recommendations are offered for
the user's consideration and examination, and it is the user's responsibility to satisfy itself that they are
suitable and complete for its particular use.
____________________________________