AN INTRODUCTION TO PUMPING EQUIPMENT

Principle, Operation & Maintenance

INTRODUCTION
Introduction

?WHAT IS THE PUMP

Pumps are machines which supply energy to a liquid in
.order to move it from place to another
Introduction

The method that is used to supply this energy to the liquid determines
the category into which the pump is placed and the system between the
.pump and the liquid final destination defines the application

Refinery Water Flood

Transportation
Introduction

:Pumps enable a liquid to

1. Flow from a region or low pressure to one of high pressure.

2. Flow from a low level to a higher level.

3. Flow at a faster rate.

Introduction

Pumps vary considerably in their size, construction

and principle of operation.

:There are two main categories of pump

 Rotodynamic pumps.

 Positive displacement pumps.

Introduction

PUMP

Rotodynamic Positive displacement

Centrifugal

Rotary Reciprocating
Axial flow

Mixed flow
Gear Piston

Turbine

Lobe Diaphragm

Sliding Vane Plunger

Screw
Introduction

Centrifugal Pumps:
Also known as rotary pumps, centrifugal pumps have a rotating
impeller, also known as a blade, that is immersed in the liquid.
Liquid enters the pump near the axis of the impeller, and the
rotating impeller sweeps the liquid out toward the ends of the
impeller blades at high pressure.

For low flows and high pressures, the action of the impeller is
largely radial.

For higher flows and lower discharge pressures, the direction of

the flow within the pump is more nearly parallel to the axis of the
shaft, and the pump is said to have an axial flow. The impeller in
this case acts as a propeller.
Introduction

Centrifugal Pumps:
The transition from one set of flow conditions to the other is
gradual, and for intermediate conditions, the device is called a
mixed-flow pump.
Introduction

Positive-displacement Pumps:
A variety of positive-displacement pumps are also available,
generally consisting of a rotating member with a number of lobes
that move in a close-fitting casing. The liquid is trapped in the
spaces between the lobes and then discharged into a region of
higher pressure. A common device of this type is the gear pump,
which consists of a pair of meshing gears. The lobes in this case
are the gear teeth
Introduction

What is the main difference

between kinetic and positive
displacement pumps ?

The main difference between kinetic and positive

displacement pumps lies in the method of fluid
transfer. 
Introduction

A kinetic pump imparts velocity energy to the fluid,

which is converted to pressure energy upon exiting
the pump casing
Introduction

A positive displacement pump moves a fixed volume

of fluid within the pump casing by applying a force to
 .moveable boundaries containing the fluid volume
Introduction

Positive displacement pumps are also divided into two

major pump categories : reciprocating & rotary.

Reciprocating pumps transfer a volume of fluid by a

crankshaft, eccentric cam or an alternating fluid
pressure acting on a piston, plunger or a diaphragm in
a reciprocating motion.
Introduction

The Table below outlines some of the main differences

between centrifugal pumps, reciprocating pumps and
rotary pumps.  Note that “centrifugal”, “reciprocating”
and “rotary” pumps are all relatively broad categories. 
The table below provides a comparison of features
between these pump categories that generally holds
true.

Also, note that Table lists typical maximum flow rates

and heads.  It is possible to build special pumps
outside the upper bounds of the pressures and flow
rates listed, but such pumps would be prohibitively
expensive for most applications.
Introduction

Rotary Pumps  Reciprocating Pumps Centrifugal Pumps Parameter

Low/Medium Capacity, Low Capacity, Medium/High Capacity, Optimum Flow and
Low/Medium Pressure High Pressure Low/Medium Pressure Pressure Applications
10,000+ GPM 10,000+ GPM 100,000+ GPM Maximum Flow Rate
Yes Yes No Low Flow Rate Capability
4,000+ PSI 100,000+ PSI 6,000+ PSI Maximum Pressure
Yes Yes No Requires Relief Valve
Smooth Pulsating Smooth Smooth or Pulsating Flow
Constant Constant Variable Variable or Constant Flow
Yes Yes No Self-priming
Requires Less Space Requires More Space Requires Less Space Space Considerations
Lower Initial Higher Initial Lower Initial Costs
Lower Maintenance Higher Maintenance Lower Maintenance
Lower Power Lower Power Higher Power
Requires clean, clear, non- Suitable for clean, clear, non- Suitable for a wide range Fluid Handling
abrasive fluid due to close abrasive fluids.  Specially- including clean, clear, non-
tolerances fitted pumps suitable for abrasive fluids to fluids with
   abrasive-slurry service. abrasive, high-solid content.
     
Optimum performance with Suitable for high viscosity Not suitable for high viscosity
high viscosity fluids fluids fluids
     
Higher tolerance for    
entrained gases Higher tolerance for Lower tolerance for entrained
entrained gases gases
 
Introduction

Centrifugal Pumps Capacity:

The wide variety of centrifugal pumps manufactured offer a
relatively large range of available capacities.  Radial-flow and
mixed flow pumps are used for low to medium capacity
applications.  For high capacity applications, axial-flow pumps are
capable of delivering flow rates in excess of 100,000 gpm. 
Centrifugal pumps are not stable at low flow rates, although there
are special low-flow centrifugal pumps available that can deliver
flow rates less than 10 gpm.  However, for extreme low-flow
applications (< 1 gpm), positive displacement pumps are a better
selection. 
Introduction

Reciprocating & Rotary Pumps Capacity:

Reciprocating and rotary pumps are capable of capacities ranging
from low to medium, with flow rates peaking at 10,000+ gpm.  In
theory, reciprocating pumps can be manufactured to deliver more
capacity, but they become prohibitively large and expensive at
high flow rates.  Both reciprocating and rotary pumps are capable
of delivering product at extremely low flow rates (fractions of a
gpm), making them particularly suitable for many chemical
injection applications.  
Introduction

Centrifugal Pumps Pressure:

Centrifugal pumps and rotary pumps are best suited for low to
medium pressure applications. 
Multi-stage centrifugal pumps can deliver at pressures of 6,000+psi and
may be the most economical choice at this pressure in high capacity
applications. 
A centrifugal pump’s pressure rise is limited to the shut-off
pressure on the pump curve, which is always less than the design
pressure of the pump (and the piping system if properly
.designed)
Introduction

Reciprocating & Rotary Pumps Pressure:

Rotary pumps as Centrifugal pumps are best suited for low to
medium pressure applications.  Reciprocating pumps are usually
specified for high pressure service, with capabilities exceeding
100,000 psi.

In most applications exceeding 1,000 psig, reciprocating pumps

are more suitable, particularly in low to medium capacity service. 
Introduction

Why it is necessary to install a relief

valve on the discharge of the
Reciprocating or Rotary pumps ?
Because both reciprocating and rotary pumps will continually
increase pressure when pumping against a closed discharge to the
extent allowed by the driver’s horsepower.  This can result in
overpressure of the pump or piping components, so it is necessary
to install a relief valve on the discharge of the pump capable of
discharging the full capacity of the pump.
Introduction

Why it is not necessary to install a

relief valve on the discharge of the
Centrifugal pumps ?
A centrifugal pump’s pressure rise is limited to the shut-off
pressure on the pump curve, which is always less than the design
pressure of the pump (and the piping system if properly designed). 
A relief valve is only needed if no other measures are provided to
detect low flow conditions and shut down the pump to prevent
damage.  The relief valve need only be sized to pass the minimum
flow rate required to maintain stable flow and prevent excessive
temperature rise. 
Introduction

Centrifugal pumps and most rotary pumps provide smooth,

non-pulsating flow, while reciprocating pumps produce a
pulsating flow.

A pulsating flow may require special design considerations in the

piping system.  If the pump is not located near the suction source,
then acceleration head can contribute to low NPSHA problems,
.which may require the installation of a suction stabilizer

A pulsation dampener may need to be installed in the discharge

.piping to reduce pressure surges resulting from the pulsating flow
Introduction

Centrifugal Pumps Variable or Constant Flow:

Centrifugal pumps operate on a variable-flow, variable-head
curve.  As the discharge pressure decreases, the pump delivers a
higher flow rate.

Centrifugal pumps are favored where process conditions often

require varying flow rates.  For example, a level control valve must
throttle the flow rate from a vessel to maintain a constant level in
the vessel.  A centrifugal pump is well suited to handle this
process condition.
 Introduction

Reciprocating & Rotary Pumps Variable or

Constant Flow:
At any given speed, reciprocating and rotary pumps operate at a
constant flow rate regardless of the discharge pressure.  There are
specific applications that require either constant flow or variable
flow.  Metering pumps rely on a constant flow at varying pressures,
which makes reciprocating pumps and rotary pumps suitable for
this application.  Piston pumps used for metering will often use an
adjustable stroke length to allow the operator to vary the flow rate
.to meet the system requirements

whereas a positive displacement pump would either require a

continuous recycle to suction or a variable speed driver to
.accommodate the variable flow
Introduction

Self-priming :
Reciprocating and rotary pumps are self-priming.  This is an
important consideration where a prime cannot be maintained on
the pump.  Centrifugal pumps are not inherently self-priming,
although some manufacturers do specially design self-priming
units.  External priming sources, such as an eductor or vacuum
pump can also be employed.
Introduction

Costs Considerations :
The reciprocating pump will generally have higher initial capital
costs and will require more space relative to the centrifugal pump
or the rotary pump.

The reciprocating pump will generally have higher maintenance

costs relative to the centrifugal pump or the rotary pump.

The centrifugal pump will generally have higher annual power

consumption costs relative to the reciprocating pump or the rotary
pump because of lower efficiencies.
Introduction

Costs Considerations :
A pump that is selected for an application outside of its optimum
operating parameters will almost certainly not follow these rules. 
For example, a rotary pump operating in a high pressure, abrasive-
slurry service would probably have higher maintenance costs than
a properly selected reciprocating pump.  The close running
clearances (particularly for high pressure service) required in the
rotary pump would likely result in premature wear and frequent
maintenance.
Introduction

Centrifugal Pumps Fluid Handling:

Centrifugal pumps are suitable for transferring a variety of fluids
ranging from clean, clear non-abrasive fluids to abrasive-slurries.
 However, a centrifugal pump is not the best choice for pumping
highly viscous fluids due to dramatic drops in efficiency at high
viscosities.  Centrifugal pumps are not normally specified for
viscosities higher than about 4,000 SSU.  Centrifugal pumps are
also not well suited to pumping entrained air.  Most centrifugal
pumps can handle up to about 2% entrained gas and specially-
designed pumps can handle up to about 10%.
Introduction

Reciprocating Pumps Fluid Handling:

Reciprocating pumps are well suited for transferring clear, non-
abrasive fluids, as well as abrasive slurries.  In fact, the relatively
low velocities of moving parts within a reciprocating pump make it
particularly resistant to erosion in abrasive-slurry applications,
provided that the pump is properly designed for the service. 
Reciprocating pumps maintain high efficiencies when pumping
highly viscous fluids and can easily handle 50% and higher
volumes of entrained gas.
Introduction

Rotary Pumps Fluid Handling:

Rotary pumps can also handle high viscosity fluids and high
volumes of entrained gas.  In fact, many rotary pumps operate at
their best efficiency at higher viscosities.  However, rotary pumps
are not well suited for pumping corrosive fluids or fluids with
abrasive solids because of close clearances between rotating and
static pump components.
 Introduction

Summary
One fact that must always be remembered: A pump does not
create pressure, it only provides flow. Pressure is a just an
.indication of the amount of resistance to flow
there are many different subcategories of pumps within these
broad categories and there are many regions of overlap
where multiple types of pumps in the same category and even
in different categories would be suitable.  Since every pump
application is unique, each of the factors that influence the
pump selection must be considered in detail.