1). Which of this statement about 4G S1 handover is correct?

1. LTE inter-eNB handover can be executed only with X2 interface

2 actLTES1Ho = 0 means S1 HO is activated
3 S1 based handover is only applicable or inter-eNB handover
4 For UE there is difference whether HO is executed via X2 or S1 interface
5 All options are incorrect

2). Issues with 4G MIMO mode control can cause by following statement, except:
1. Inappropriate selection between the two transmission schemes
2. Ping-Pong between spatial diversity and spatial multiplexing
3. Switching between transmission schemes to create additional signalling
4. Inappropriate' selection between spatial diversity and spatial multiplexing
5. All options are incorrect

3). What is a3offset ?

1. A threshold for RSRP Neighbor Cell so that intrafreq HO can perform
2. A threshold for RSCP WCDMA Cell so that intraRAT HO can perform
3. A threshold for RSRP Serving Cell so that intrafreq HO can perform
4. A margin between RSRP Neighbor and RSRP Serving Cell
5. All options are incorrect

4). In the 3GPP evolved release 10, transmission modes are support to:
1. Single Antenna Port or Tx Diversity & 4x4 MIMO in the downlink
2. Tx Diversity & Closed Loop Spatial Mux with single Layer
3. 8x8 MIMO in the downlink or Dual Layer Beamforming
4. Tx Diversity & Closed Loop Spatial Mux (Close Loop MIMO)
5. All options are incorrect

5). If we set Parameter PowerOffsetLastPreamblePRACHmessage 2db, what is the recommended value for
parameter PowerRampStepPRACHpreamble that effecting to open loop power control :
1. 0db
2. 1db
3. 2.db
4. 4db
5. All options are incorrect

6). Which of this statement about 4G DL Physical Channel is not correct?

1. Reference Signal occupies at least 8 RE per RB
2. PDCCH occupies the REs not used by PCFICH and PHICH and Reference Signals within the first 1, 2 or 3
symbols of each TTI
3. PDSCH occupies the central 72 subcarriers across 2 symbols
4. PCFICH occupies up to 16 RE per T I
5. All options are incorrect
11). Reference Signal occupies how many resource element in 2 transmit antennas?
1. 16
2. 32
3. 8
4. 24
5. All options are incorrect
12). What is the side effect could be happen on applying DRX/DTX
1. Increase Power Consumption
2. Longer Call Setup Time
3. Save Power Comsumption
4. Increase paging repition
5. All options are incorrect

13). What is the benefit of a Tracking area list?

1. Minimize paging and TAUs
2. TA list ensures that the location of UE is available to the MME at all instants of time
3. Increase the number of TAs
4. Increase latency
5. All options are incorrect

14). What kind 4G System Information Broadcast can provide?

1. Non-Access Stratum information Only
2. Access and Non-Access Stratum information
3. eUTRAN related parameters
4. Access Stratum information Only
5. All options are incorrect

15). Handover are essenstial procedure for UE moving from cell to cell. What are the 4G Handover Event ?
1. Al—Interfreq, A2—Intrafreq, A3—BetterCell, A4—BetterCell, A5— CoverageBased
2. Al Intrafreq, A2 Interfreq, A3 BetterCell, A4 InterRAT, A5- CoverageBased
3. A1—Intrafreq, A2—InterRAT, A3—CoverageBased, A4— Interfreq, A5 BetterCelI
4. Al BetterCell, A2 Intrafreq, A3- Interfreq, A4- CoverageBased, A5 InterRAT
5. All options are incorrect

18)How we can identify the GPS in 4G TDD have problem?

1. RSSI PUCCH increase
2. RSSI PUSCH increase
3. Handover Interfrequency will degraded
4. Payload will reduced
5. All options are incorrect

19). Is there any relation between low 2G CSSR and high capacity ?
1. Yes there is, CSSR is all about congestion
2. It depends on the CSSR formula
3. Depend on the site to site distance
4. No relation because CSSR is about Quality
5. All options are incorrect

20). Which of the following that you will not do if you find 2G TBF Downlink Success Rate is not pass the
target baseline ?
1. Adjust GTRX number and CDED/CDEF
2. Switch GTRX to better quality TRXs
3. Reset the GTRX, GENA, EGENA
4. Downtilt from 4 to 10
5. All options are incorrect
21). What is the main use of GPS in 4G TDD?
1. To know the position of the UE
2. To know the position of the eNB
3. Frequency synchronization
4. Time & Clock Synchronization
5. All options are incorrect

22). In 4G Power control, What is the role of Alpha?

1. alpha =1 in our network full eliminate of path loss
2. alpha = 0 in our network full eliminate of path loss
3. alpha = 0 in our network full compensation of path loss
4. alpha =1 in our network full compensation of path loss
5. All options are incorrect

23). When we required for 4G Random access process ?

1. Initial Access from RAB Idle
2. DL data arrival during RRC_DISCONN ECTED
3. Initial Access from RRC Idle
4. RAB Connection Re-tablishment procedure
5. All options are incorrect

24). When throughput test shows low throughput value for TCP, but UDP throughput is high, what could be
the cause?
1. Not enough BTS baseband capacity
2. Shaping is enabled in the transport path between the core and eNodeB
3. Packet loss somewhere between the core network and eNodeB
4. Test is done too close to the site
5. All options are incorrect

25). An eNodeB BW 15 Mhz, pMax = 448, AVG_UE_DIST = 2.1 Km, expectedCellSize=2 (5 Km),
dlMimoMode=40, below actions are to improve Throughput, except ?
1. change expectedCellSize to 1 (2.1 Km)
2. change pMax to 460
3. upgrade BW to 20 Mhz
4. change dlMimoMode to 43
5. All options are incorrect

26). what is below is not correct condition that cell reselection will trigger in 4G inter-frequency?
1. Squal <= SlntraSearchQ
2. RSRQ >= qQualMin + slntraSearchQ
3. Srxlev <= SnonlntraSearc hP (benar)
4. RSRP <= qrxlevmin + slntraSearchP
5. All options are incorrect

27). what is below is not correct condition that cell reselection will trigger in 4G intra frequency?
1. Qrxlevmeas - Qrxlevmin <= Sintrasearch
2. Srxlev <= Sintrasearch (benar)
3. Qrxlevmeas <= Qrxlevmin + Sintrasearch
4. Qrxlevmeas - Qrxlevmin < Sintrasearch
5. All options are incorrect

28). What is true about Tracking Areas (TA) in LTE?

1. TA must be same as the area served by one MME gateway
2. One cell has to be connected with only one TA
3. TA must be exactly the same as the Location Areas in a 3G co-located network
4. One cell can belong to several Tas
5. All options are incorrect

29). Which of the following parameter mush have the same setting for Pcell and Scell when CA is activated?
1. riEnable (rank indication reporting enables). 2. periodicCqFeedback Type (periodic CQI feedback type) 3.
cqPerSbCycK (Periodic CQI sub-bands cycles) 4. caShecFairFact (carrier aggregation scheduling fairness
control).
1. 1), 2) and 4)
2. 1), 2), 3) and 4)
3. 2), 3) and 4)
4. 1), 3) and 4)
5. All options are incorrect

30). What is Cell Change?

1. Transfer of an ongoing call/data session from a cell to another without call interruption
2. Cell reselectio from cell to another cell
3. Transfer of an ongoing call/data session from a cell to another, but requires connection release prior to the
transfer the ongoing call
4. Procedure dedicated for call transfer from LTE to GSM; it requires connection release
5. All options are incorrect
31). Which Channel Carries 4G Paging message?
1. PUSCH
2. PDCCH
3. PDSCH
4. PBCH
5. All options are incorrect
32). There are some use cases of 4G cross-carrier scheduling, except:
1. Increasing PUCCH/PHICH overhead
2. b. Mitigating the control channel coverage limitation of low BW component carrier
3. Support of PDCCH-less component carriers for purpose of improved interverence management, for
example in heterogenous network deployments (Ie. ICIC for PDCCH)
4. Avoiding PDCCH transmission on DL CCs that are close in frequency to UL CCs to avoid desensing the
receiver.
5. All options are incorrect

33). How many carrier per pipe maximum for AHHB Nokia AirScale RRH 4T4R ?
1. Up to 16
2. Up to 8
3. Up to 12
4 Up to 4
5. All options are incorrect
34). In 4G Intrafreq handover, in what condition UE will not measure or report any neighbor cells RSRP ?
1. If RSRP of neighbor cell is lower than threshold1, only neighbor cell is measured
2. If RSRP of serving cell is greater than threshold1, only serving cell is measured
3. if RSRP of neighbor cell is greater than threshold1, only serving cell is measured
4. If RSRP of serving cell is lower than threshold1, only serving cell is measured
5. All options are incorrect

35). It is possible to configure a UE to aggregate a different number of Component Carrier (CCs) originating
from the same eNB and of possibly different bandwidths in the UL and the DL, except:
1. 4db
2. In typical TDD deployments, the number of CCs and the bandwidth of each CC in UL an DL is the same.
3. d.CCs originating from the same eNB need not provide the same coverage
4.The number of DL/UL CCs that can be configured depends on the DL/UL aggregation capability of the UE
5.All options are incorrect

36). What is the first thing you do when you find degradation on KPI?
1. Fallback your parameter change that you do yesterday
2. Check hardware alarm and packet loss rate
3. Check the availability measurement to detect if any missing hour of measurement
4. Check if any parameter change from the day before
5. All options are incorrect

37). The CQI is defined as a table containing 16 entries with modulation and coding schemes (MCSs). Which
one is correct for representing the modulation ?
1. CQI 1-6 = QPSK, CQI 7-9 = 16QAM, CQI 10-15 = 64QAM
2. CQI 1-5 = QPSK, CQI 6-8 = 16QAM, CQI 9-15 = 64QAM
3. CQI 1-6 = QPSK, CQI 7-10 = 16QAM, CQI 11-15 = 64QAM
4. CQI 1-6 QPSK, CQI 7-11 = 16QAM, CQI 12-15 = 64QAM
5. All options are incorrect

38). Which one is correct about T300 and T301?

1. T300 : supervises the RRC connection establishment procedure
2. T301 : supervises the RRC connection establishmen procedure.
3. T300 : supervises the connection re-stablishment procedure.
4. T301 defines the validity time of dedicated priorities defined in IdleModeMobilityCon trollnfo.
5. All options are incorrect
39). What is the parameter you will change if you want to decide the absolute priority of the 4G serving cell
1. cellReSelPrio (This is the priority of the own cell. It depends on the layering plan. The cell reselection
priority parameter defines the absolute priority of the serving layer. 0 means the lowest priority. Equal
priorities between RATs are not supported according to [3GPP 36.304].)
2. uCelResPrio (Depends on layering plan. LTE prio > 3G prio > GSM prio. Absolute priority of the UTRA carrier
frequency. Equal priorities between RATs are not supported according to [3GPP 36.304].
3. gcelResPrio (LTE prio > 3G prio > GSM prio. Its value depends on layering plan of the operator. Usually
GERAN would be the last resort coverage layer and low priority is used. Absolute priority of the GERAN carrier
frequency. Equal priorities between RATs are not supported according to [3GPP 36.304].
4. eutCelResPrio (Depends on layering plan. Absolute priority of the EUTRA carrier frequency. Equal priorities
between RATs are not supported according to [3GPP 36.304].
5. All options are incorrect

40). There is 4 types on preamble, what is the significant difference between this 4 types ?
1. PRB Number
2. Reference Signal
3. Cell Range
4. Guard Time
5. All options are incorrect

41). What is the benefit of ICIC?

1. Increase UL RSSI Interference
2. Improve the RSRP for the cell-edge users
3. Improve the OSR for the s rs
4. Improve the SINR for the cell-edge users
5. All options are incorrect

42). Which procedure changes the UE state from ECM-IDLE to ECM-CONNECTED?

1. Default bearer creation
2. S1 Release
3. PGW Selection
4. Service request
5. All options are incorrect

43). Which of the folllowing is not correct about the reason of 4G ERAB Drop ?
1. HARQ ACK/NACK RLF
2. PUSCH RLF
3. TA Expiry
4. Srxlev > 0 and Squal > 0
5. All options are incorrect

44). Which network element of NOKIA's LTE solution performs the E2E monitoring and reporting functions?
1. Flexi NG
2. Charge@once
3. PCS-5000
4. Netact
5. All options are incorrect
45). What parameter to define the maximum numbers of preambles allowed in one preamble ramping cycle ?
1. PowerRampStepPRACHpreamble (“The power ramping step size parameter defines the power increment
step size for Random Access preamble transmission.”)
2. PRACHRequired ReceivedCI
3. PRACH_Preamble_retrans
4. UETxPowerMax PRACH
5. All options are incorrect

46). What is the bad impact on applying Closed Loop Power Control in 4G ?
1. UL RSSI will degraded
2. DL User Throughput will degraded
3. No bad Impact
4. UL User Throughput will degraded
5. All options are incorrect

47). What is parameter cellreselprio do ?

1. De-prioritizing the serving band on idle mode
2. Prioritizing the serving band on idle mode
3. De-prioritizing the serving band on connected mode
4. Prioritizing the serving band on dedicated mode
5. All options are incorrect

54. Select the factor that does NOT improve the Spectral Efficiency In Massive MIMO ?
1. Multiuser gain
2. UL interference cancellation
3. 3D beamforming
4. SINR Improvement due to narrower UE beam
5. All options are incorrect

59. What is timing advance show to us ?

1. A coverage signal distance that cell can reach
2. The timing tha UE finished th download
3. The clock timing in TDD system
4. A distance between source cell to neighbor cell
5. All options are incorrect
60. Which of the following options does NOT improve the latency as part of the Radio Network Optimization
Procedures?
1. Enabling/Disabling Proactive Scheduling
2. Tuning the scheduling request period
3. Tuning DRX cycle duration
4. Increasing PUCCH capacity
5. All options are incorrect

61. Which of the following bandwidth is NOT defined in LTE ?

1. 5MHz
2. 2MHz
3. 10 MHz
4. 20 MHz
5. All options are incorrect
62. What you know about alarm 7445 in 2G Band ?
1. This alarm is an environment alarm, can be ignored
2. Immediately change module hardware if you find alarm 7445
3. Take action depend on supplementary info and how frequent it happen
4. Add more SDCCH and PDCCH to reduce the impact
5. All options are incorrect

63. How does MIMO improve spectral efficiency, network capacity and throughput
1. By using multiple uplink and downlink transmitters
2. By using multiple receiv and transmit antennas
3. By using multiple eNB sites
4. By using multiple transmit and receive amplifiers
5. All options are incorrect

64. What is the bad effect could be happen on applying DRX/DTX

1. Longer Call Setup Time
2. Increase paging repition
3. Save Power Comsumption
4. Increase Power Consumption
5. All options are incorrect

65. What is the benefit of 2G halfrate ?

1. Improve call drop
2. Increase capacity but reduce quality
3. Increase Paging Succsess rate
4. Increase capacity and ncrease quality
5. All options are incorrect

66. What air interface technology has been defined for LTE uplink ?
1. SC_FDMA
2. WCDMA
3. GSMK
4. OFDMA

67. Which type of handovers are support in LTE?

1. Hard and Soft handovers
2. Hard, Soft and Softer Handovers
3. Handover is not supported
4. Hard Handover only
5. All options are incorrect

68. what is below is correct condition that cell re-selection will trigger measurement in 4G intra-frequency?
1. If cannot do inter-frequency handover then do intra-frequency handover
2. Cell re-selection only happen in 4G Inter-frequency
3. Qrxlevmeas > Qrxlevmin + Sintrasearch
4. Qrxlevmeas <= Qrxlevmin + Sintrasearch
5. All options are incorrect
69. what is below is correct condition that cell reselection will trigger in 4G inter-frequency?
1. RSRP <= qrxlevmin + sNonlntraSearchP
2. If cannot do intra-frequency handover then do inter-frequency handover
3. RSRP > qrxlevmin + sNonlntraSearchP
4. Cell re-selection only happen in 4G Intra-frequency
5. All options are incorrect

70.You are in optimizing 1 new site, you see 2G TCH Blocking is not Pass the target KPI. What will you do ?
1. Disable the Halfrate so the cell can go full rate to accomade full service
2. Check if VOLTE 4G is not activated yet
3. Adding PDCCH channel to reduce the tch blocking
4. reduce the SDCCH channel, so that no UE can not do setup
5. All options are incorrect

71. What are NOT the reason in Handover preparation failure?

1. Bad Quality on target Cells
2. Tx2relocation timer
3. X2 issue
4. Congestion on target Cells
5. All options are incorrect

72. What will you do if find cell with high PRB Utilization ?
1. Wait until any PO new site suurounding released and ON AIR
2. Offload to 3G with high BB Util
3. Downtilt from 2 to 10
4. Try to do payload sharing to neighbor cells
5. All options are incorrect

73. What is NOT the reason of Ping-pong handover?

1. Improper handover margin
2. No dominant cell coverage
3. Bad Quality Interference
4. Cell Re-selection is too fast
5. All options are incorrect

77. Which factors can NOT be a cause for bad KPI for HOSR ?
1. IMSI
2. X2 quality
3. Layer Priority
4. UL RSSI
5. All options are incorrect
78. Which one of these KPI include in 4G Quality category?
1. RTWP
2. PRB Utilization
3. Intracell Handover
4. CQI
5. All options are incorrect
79. You are in optimizing 4G New Site, but you find that the Packet Loss Rate is high. What will you do first?
1. Check in hourly basis if packet loss is happen frequently or just a spike
2. Immediately escalate to transport Engineer to seek support
3. Perform drive test to check the field impact
4. Check hardware alarm if any baseband module broken
5. All options are incorrect

80. You are optimizing 1 new site and 4G Payload suddenly increase and impact to your CSSR KPI, what will
you not do immediately?
1. Check if any site surrounding site if shutdown
2. Check if any promo campaign to up the sales
3. Check your validity of your measurement if any double counting
4. Payload Increase is good, so make justification for CSSR KPI
5. All options are incorrect

81. From Drive Test Result, to check coverage of the cells, What plotting will you used ?
1. RxQual on dedicated mode
2. RxLevel (dBm) on idle mode
3. RxQual on Idle mode
4. RxLevel (dBm) on dedicated mode
5. All options are incorrect

82. What MDT(Minimize Drive Test) Can Not do?

1. Check Signal strength and Quality
2. Functionality Test Call 5x, SMS 5X
3. Check Throughput
4. Check Cross feeder

83. Do you think this formula is correct or not CSSR 4G = RRC – SR% X RAB-SR% X S1-SR%?
1. Not correct, because CSSR 4G only count RRC-SR
2. Correct, but must confirm to customer if S1-SR included or not
3. Correct, but must be confirm to customer if S1-SR included or Not
4. Correct and must have this 3 component

84. Which of the following is incorrect types of handover in LTE ?

1. Intracell HO, Soft HO, hard HO
2. Intrafreq HO, Interfreq HO, IRAT HO
3. Volte HOSR, SRVCC HOSR
4. X2 HO, S1 HO, IRAT HO

85. There is a complain 2G cannot make a call at all, what the best should you check ?
1. Check 2G can do PS data
2. Check if connected to correct SGSN
3. Check BCCH frequency is clear or not from interference
4. Check LAC-CI already registered in Core

86. UL CA Stratum Access Category :

1. Rel10
2. Rel9
3. Rel11
4. Rel8
87.Which tools is NOT recommended in the Global NPO Tools Portofolio?
1.9955RNP
2.Asset Radio
3.Mentum Planet
4.Atoll

88.Which sentence is NOT true concerning Cell trace and Subscriber trace?
1.Both Cell trace and subscriber Trace, indentify UE based upon their IMSI
2. Cell trace records all the UEs connected to the hell, whereas Subscriber Trace record only specific UE
3. The cell trace, trace activation command is sent to the enb, whereas the Subscriber Trace, Trace Activation
command is sent to the MME
4. Cell trace does not capture the subscriber identify, whereas Subscriber Trace captures the IMSI

89.Which statement(s) correctly describe the SBTS site configuration evolution:

1. Cell sets define onsub baseband module level are combined in independent building blocks to build an
SBTS configuration
2.LTE and SRAN cell set can flexibly combined to build target configuration
3.”Cell set” approach isadobted from LTE. Requires higher effort on LTE migration from legacy RAT to SRAN in
comparison to the “Profile” approach
4. “Cell set” concept is only applicable to the shared operation SRAN cells
1. 2 and 3
2. 2 and 4
3. 1 and 4
4. 1 and 4

90.Which physical channel must be dimensiond when LTE CA feature is activated

1. PRACH
2. PUCCH
3. PDCCH
4. PUSCH

91.Which Statement is FALSE about smart admission control

1.It support GBR and non GBR traffic
2.Data DRB are admitted/rejected comparing cell internal counters agains configured threshold<br/>
3.For new GRB-DRB bearers the forecast on needed resources is based on periodical measurement
4.It usually work together with the Allocation and retention priority feature

98. Nokia Single RAN solution is designed to support multiple Radio Access Technologies with common or
shared functionalities. Which og the following statement are correct?
1.Single FSMF baseband capacitycan be shared between GSM+WCDMA or GSM+LTE but not LTE+WCDMA
2.Common BTS OAM to simply site creation commissioning and configuration process, where IOMS is re-
used to handle SRAN operability
3.SRAN solution is compatible with FSME, FSMF and Air Scale system module
4.Air Scale System Module can be used as two logical SBTSs in full subrack, or one logial SBTS and one logial
LNBTS and one logial LNBTS in full subrack

1.2 and 4
2.1 and 2
3.2 and 3
4.1 and 4
99. Select all the statements) which are correctly describing the Uplink Power Control
function/algorithm:
1. Uplink Power Control is trade-off between inter-cell interference and own cellthroughput
2. Closed loop ULPC is UE oriented, SIN and RSSI target window power control
steering
3. Interference Aware ULPC replace Closed Loop ULPC for PUSCH/SRS, but keep OLPC algorithmuntouched
4. UL Interference Offset feature overcomes the impact of power restrictions on PUCCH allocating PUCCH
away from power restrick region.
1. 1, 2, 3 and 4
2. 1, 3 and 4
3. 1 and 3
4. 2 and 4

100.Which protocol stack layer within the enb is responsible for uplink and downlink adaptation?
1. RLC Layer
2. MAC Layer
3. Physical Layer
4. PDCP Layer
103. What statement releated to PDCCH capacity is false?
1. PDCCH is always tramsimtted using QPSK
2. PCCH capacity for MIMO 4X2 is lower than for MIMO 2X2
3. Feature usage based adaption increase the absolute capacity of the PDCCH
4. When PDDCH blocking happens the user’s connection is maintained but there is an increased delay in the
resource allocation

108. Which of the following is NOT correct about the reason of 4G ERAB Drop?
1.PUSH RLF
2.Srxlev > 0 and Squal > 03.CQI Report RLF
4. HARQ ACK / NACK RLF
5. All Options are incorrect

109.Which radio technology does LTE use?

1.CDMA
2. FDMA
3. OFDMA
4. TDMA
5. All options are incorrect

110.Which interface allows application data transfer through the Serving Gateway
1. LTE Uu
2. X2
3. S1-MME
4. S1-U

111.Which managed objects are not a part of GSM technology (more than one option can be valid)
1.WCEL
2. BTS
3. TRX
4. BCF