0% found this document useful (0 votes)
492 views5 pages

BTT Tft35-E3 v3.0 User Guide

This document is a user guide for the BIGTREETECH TFT35 V3.0 3D printer display. It introduces the display's features such as a 120MHz STM32F207VCT6 chip, SD card firmware updates, compatibility with different printer models, and touchscreen or non-touchscreen modes. It also provides information on the display's ports and connectors, firmware installation, and notes on safe installation and use.

Uploaded by

nacho vadillo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
492 views5 pages

BTT Tft35-E3 v3.0 User Guide

This document is a user guide for the BIGTREETECH TFT35 V3.0 3D printer display. It introduces the display's features such as a 120MHz STM32F207VCT6 chip, SD card firmware updates, compatibility with different printer models, and touchscreen or non-touchscreen modes. It also provides information on the display's ports and connectors, firmware installation, and notes on safe installation and use.

Uploaded by

nacho vadillo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Shenzhen BIGTREE Technology CO., LTD.

BIG TREE TECH

BIGTREETECH
TFT35 V3.0
User Guide
Shenzhen BIGTREE Technology CO., LTD.
BIG TREE TECH

Ⅰ.Product Introduction
BIGTREETECH TFT35-E3 V3.0 is a medium size, dual-mode,

ultra-clear 3D printing machine display launched by the 3D printing team

of Shenzhen BIGTREE Technology CO., LTD., which can perfectly

replace the original LCD screen of Ender3 printer.

1.Product characters:
1)ARM Cortex-M3 series STM32F207VCT6 chip with 32-bit CPU 120MHz;
2)Upgrade the firmware by SD card. It is easy and convenient to operate.
3)This display board has higher compatibility. Users can select two work modes:
UART serial port screen mode and 12864 screen mode.
4)Serial port screen mode supports two printing modes: SD card and U disk.
5)Reserve WIFI port, and WIFI function is realized by external WIFI module;
6)Reserve the extension port of filament breaking detection (FIL-DET);
7)Reserve the extension port of automatic shutdown after printing (PS-ON);;
8)LCD12864 mode uses EXP1, EXP2 and EXP3. EXP1 and EXP2 are LCD
screen ports of normal motherboard. EXP3 is the LCD interface used by E3 series
motherboard (such as SKR MINI E3 V1.2, SKR E3 DIP V1.1, etc.) ;
9)TFT touch screen mode:serial port screen RS232 port;
10)2 sets of UART serial port extension ports are reserved for DIY use.

2.Product Parameters:
Appearance size:93*87mm
Installation size:Perfectly replace the original LCD screen of Ender3 printer,
detail information please check TFT35-E3 V3.0 SIZE
Microprocessor:STM32F207VCT6
Power Input:DC 5V
SD card logic voltage:3.3V and 5V(Such as: support MEGA2560 main control
chip motherboard, higher compatibility)

Ⅱ.Indicator Information
After the board is powered on:
Red light D6 is the power indicator: the red light is on, indicating normal
power supply;
Green light D3 is SD card detection indicator: D3 is always on when the SD
card inserted, and then off when SD card pulled out
Shenzhen BIGTREE Technology CO., LTD.
BIG TREE TECH

Ⅲ.Ports on the board


1.Size diagram

2.Connection diagram
Shenzhen BIGTREE Technology CO., LTD.
BIG TREE TECH
Notes:
1. When using 12864 screen mode, connect the port EXP1 and EXP2 to the
motherboard. There is no touch function in this mode.
2. When using serial port screen mode, connect with TFT or AUX-1 on the
motherboard via RS232. This mode has touch function;
3. Two work modes can be changed by one key. Press the encoder about 3
seconds until the mode selection page appears, then press the encoder
after selecting the mode.

Ⅳ.Firmware Introduction
Factory board will be equipped with test firmware, it can be used directly.
It can also be upgraded according to our company's open source website.
1. Ways to obtain the firmware of motherboard
Get it from customer service or technical staff;
Log in the open source website of our company to download :
https://github.com/bigtreetech
2. Firmware update
Firmware file name::
BIGTREE_TFT35_V3.0. (version number).bin
First copy the above firmware to SD root directory, and then insert the card into
the SD card slot of the board. Next please re-power the board or press the reset
key, and wait for about 10 seconds before the update is completed.;
3. For DIY board firmware, please refer to the file TFT35-E3 V3.0PIN.

Ⅴ.Notes:
1. The name of the firmware file in the SD card cannot
be changed. (including capital and small letters);
2.The wiring process must be carried out under the
premise of power failure. The power can be put on after
checking the correct connection of the circuit and the
correct insertion of the drive. This prevents boards
and screens from burning up due to faulty wiring,
causing unnecessary damage.;
Shenzhen BIGTREE Technology CO., LTD.
BIG TREE TECH

3.Pay attention to the wiring sequence and do


not insert the wire inversely. Please refer to PIN
file for detailed line order.

If you encounter other problems, please contact us, we will

definitely answer your questions patiently; If you have any good

suggestions on our products, please give feedback to us, we will

consider them. Thank you for choosing BIGTREETECH products!

You might also like