BITUSTICK AL

Aluminum surfaced solar reflective

self-adhesive waterproofing membrane
Bitustick AL
Aluminum surfaced solar reflective waterproofing membrane
Polymer modified bituminous self adhesive waterproofing membrane

CHARACTERISTICS
► Good resistance to water & vapor
► Aluminum surfacing, Excellent solar reflectance
► Specially formulated for tropical climates
► Self adhesive. Requires peeling off of the silicone film
and sticking to the surface
► Excellent adhesion to vertical and horizontal surfaces

TDS_Bitustick AL_GCC_0519
► Good tear and puncture resistance
► Excellent tensile strength in both longitudinal and
transverse direction

self adhesive waterproofing

DESCRIPTION 1
Bitustick AL is a tropical grade polymer modified
bituminous self adhesive waterproofing membrane. The
bitumen compound is laminated onto an impervious, Priming
non-perforated, cross laminated solar reflective aluminum Apply Polyprime SB* (Solvent based primer) @ 4- 6 m²/L
surfaced HDPE film. to a clean smooth and dry surface by brush, roller or spray.
Allow the primer to dry prior to the application of the
FIELDS OF APPLICATION membrane. As the viscosity of the primer is low, it easily
BITUSTICK AL is a multi purpose waterproofing membrane penetrates into the concrete pores which in turn promotes
which may be used for mobile homes, small commercial the adhesion between the membrane and the concrete
roofs, residential porches and dormers, farm buildings, roof surface. In addition, the primer also acts as a binder for
and gutter patching and on profile sheets. It can also be the dust which gets accumulated on the surface even after
used as a flashing on up-stands. cleaning.
APPLICATION INSTRUCTIONS Alignment
The application temperature should be between 5°C to Start the installation of all membrane plies from the low
55°C. Application procedures may vary slightly depending point or drains, so the flow of water is over or parallel to
upon site conditions. The general recommended guidelines the plies, but never against the laps. All overlaps at the
for the application of the self adhesive waterproofing membrane seams shall be installed so as to have "up" slope
system is as follows: laps over "down" slope laps. Begin membrane application
by unrolling the roll of Bitustick AL membrane and aligning
Surface preparation the side laps .
The surface shall be cleaned thoroughly of all contaminants
like dust, traces of curing compound, oil and grease. All Application
surface imperfections, protrusions, structurally unsound Peel off the release film from the self adhesive side and
and friable concrete must be removed and repaired with a start unrolling the membrane and press it to the surface.
suitable Polycrete* concrete repair mortar. Smoothen the membrane from the center to the edges
with a wooden press in order to remove any entrapped
air. Furthermore, an iron roller shall be used for rolling
 on top of the applied membrane to ensure a proper and TECHNICAL SPECIFICATION
strong adhesion of the bitumen compound with the base
PROPERTIES VALUES TEST
surface. Side overlaps shall be a minimum of 50mm on
STANDARDS
the selvedge and end overlaps 100mm. When used as a
flashing membrane on up-stands and parapets, Bitustick Thickness, [mm] 1.2 1.5 DIN EN 1849-1
AL membrane will be lapped with the base membrane and Mass per unit area, 1.2 1.5 DIN EN 1849-1
taken up on the up-stand and tucked inside the groove [kg/m2]
cut along the parapet wall. The tucked membrane will be Top surfacing Grey/Silver -
sealed with a bitumen mastic sealant (BITUMASTIC)*. Cross laminanated
HANDLING HPDE aluminum foil
Bitustick AL membranes are packed in loose corrugated Softening point, (R&B), [°C] >105 ASTM D 36
boxes to avoid any damage during transit or during storage Tensile strength Long 40 ASTM D 882
at sites. Care should be taken when storing the membranes [Film], [N/mm2] Trans 45
on sites and should not be kept within close proximity of Elongation @break Long 150 ASTM D 882
any sharp or protruding edges to avoid puncturing or [Film],[%] Trans 150
damaging the membrane. Tear strength [Film], Long 20 ASTM D 1004
STORAGE & SHELF LIFE [N] Trans 20
Bitustick AL membranes must be stored in a shaded area Adhesion strength,
on wooden pallets neatly covered by a thick fabric and [N/mm]
tied securely in a manner that will minimize exposure to Primed substrate 1.8 ASTM D 1000
sunlight and UV. The membrane shall be protected from Self 2.2
all sources of heat. The shelf life is 12 months if stored Puncture resistance, [N] >220 ASTM E 154
as per recommendations. Excessive exposure to sunlight,
TDS_Bitustick AL_GCC_0519

Reflectance, [%] > 60 EN 410

UV and other sources of heat will result in considerable
Hydrostatic pressure No BS EN 12390
deterioration of the product and reduce its shelf life.
@ 5bar (50m) Leakage (Part 8)
HEALTH & SAFETY Water absorption 0.14 ASTM D 570
Bitustick AL contains a tacky bitumen compound which can [Film] @24 hrs, [%]
stick to human skin during application. Bitumen stains can Chemical resistance, [pH] 2.5-11.5 ASTM D 543
be removed by using a cloth dipped in a suitable cleaner. Low temperature <-15°C ASTM D 1970
SUPPLY flexibility
2
Crack bridging >1 ASTM C 836
Bitustick AL 1.2 mm 1m x 10 m wt 12kg# ability, [mm]
1.5 mm 1m x 10 m wt 15kg#
VOC [g/l] <50 ASTM D3960/
Polyprime SB 20L pail & 200L drum D2369
Bituboard 3.2 mm 2m x 1m wt 7.7kg# All values given are subject to 5-10% variation
6.0 mm 2m x 1m wt 14.0kg#
Watertite TS 15 50mm x10m wt 0.6kg# Apart from the information given here it is also important to observe the relevant
guidelines and regulations of various organisations and trade associations as
Wooden Press 140mm x 210mm well as the respective standards. The aforementioned characteristics are based
Iron Roller Head Dia 38mm wt 1.5 kg# on practical experience and applied testing. Warranted properties and possible
uses which go beyond those warranted in this information sheet require our
(recommended Width 100mm written confirmation. All data given was obtained at an ambient and material
specification) Length 350mm temperature of +23°C and 50 % relative air humidity at laboratory conditions
unless specified otherwise. Please note that under other climatic conditions
*Refer to website for TDS # Approximate weight hardening can be accelerated or delayed.
The information contained herein, particularly recommendations for the
handling and use of our products, is based on our professional experience.
As materials and conditions may vary with each intended application, and
thus are beyond our sphere of influence, we strongly recommend that in each
case sufficient tests are conducted to check the suitability of our products
for their intended use. Legal liability cannot be accepted on the basis of the
contents of this data sheet or any verbal advice given, unless there is a case
of wilful misconduct or gross negligence on our part. This technical data sheet
supersedes all previous editions relevant to this product.

Henkel Polybit Industries Ltd.; PO Box: 293, Umm Al Quwain, UAE

Tel:+971(6)76 70 777; Fax:+971(6)76 70 197; [email protected]
Henkel Polybit Industries Ltd.; PO Box: 5911, Dammam-31432, KSA
Tel:+96613808 4061 / 62, Fax: +966 13 812 1164; [email protected]
www.henkelpolybit.com
MS_Bitustick-AL_GCC_0917_GR0

METHOD STATEMENT
BITUSTICK AL
SECTION I: GENERAL INSTRUCTIONS
 All materials whether loose or on pallets have to be stored in a covered area and protected from
UV and sunlight. Damage to the membrane may be caused due to improper storage and at high
temperatures.
 Application of membranes should be avoided in case of extreme weather conditions like sand
storm or rain.
The ambient temperature during application should be between 5°C and 55°C.
The following Equipment’s are required during application:
Protective clothing:
Gloves, face mask, overalls, and safety goggles
Application equipment’s:
 Slow speed drill machine with less than 500 rpm with a suitable spiral mixer
 Wooden press & lap rollers
 Brush /roller
 Steel scrapper
 Cotton waste
 Solvent cleaner
 Measuring tape
 Cutting knife, scissors
SECTION II: APPLICATION INSTRUCTIONS
Surface Preparation:
The concrete surface shall be cleaned thoroughly of all contaminants like dust, traces of curing
compound, oil, grease. All surface imperfections and protrusions are to be removed and repaired.
Structurally unsound and friable concrete must be removed and repaired with a suitable concrete
repair mortar. All nail heads and protrusions that are likely to puncture the membranes must be
removed.
Provide a 45-degree cement sand angle fillet on all internal corners and a 20mm chamfer on all
external corners.
Priming:
All concrete surfaces shall be primed by solvent based bitumen primer (POLYPRIME SB) as per
ASTM D 41 /BS 3416. Mix the contents of the pail/drum prior to the application to remove any
sediment. Apply the primer @ 4-6 m²/lt by a brush, roller or an airless spray. Allow the primer to dry
prior to the application of the waterproof membrane.
If membrane application gets delayed for more than 24 hours after the primer has been applied on
the concrete surface, then apply a fresh coat of the primer again.
Application-Flat Horizontal Surfaces:
BITUSTICK AL membranes shall be installed from the low point or drains, so the flow of water is
over or parallel to the plies, but never against the laps. All overlaps at the membrane seams shall
be installed so as to have "up" slope laps over "down" slope laps.
Unroll only the required length of the membrane and cut the pieces to the desired length and
shape.
Place the membrane pieces on the area to be covered and check whether the piece’s match with
the profile of the marked substrate.
MS_Bitustick-AL_GCC_0917_GR0

Re-roll the membrane for about half the length without changing its orientation. Then slowly unroll
the membrane, peel off the release film and carefully place the membrane on the surface.
Smoothen out any entrapped air by pressing from the center to the sides by the wooden press.
Furthermore, an iron roller shall be used for rolling on top of the applied membrane to ensure a
proper and strong adhesion of the bitumen compound with base surface.
The subsequent rolls shall be laid to have a 50mm overlap on the selvedges and end overlaps of
100mm.
A 50mm cement sand protective screed (with 10mm down aggregate size) shall be provided on top
of the applied membrane in order to protect it from damage from reinforcements and sharp
aggregates present in the concrete.

Application-Vertical Surfaces
Reinforcing strips of 200mm width cut out from the BITUSTICK AL membrane shall be applied on
all the corner joints.
Dimension of the area, which needs to be waterproofed, shall be taken and the membrane is
aligned accordingly. The membranes are then re-rolled and then un-rolled slowly and stuck to the
surface by peeling off the silicone release film and exposing the self-adhesive side. Entrapped air
shall be smoothened out from the center to the sides by a wooden press followed by rolling with an
iron roller to ensure a proper and strong adhesion of the bitumen compound with base surface.
The membrane will be finished on the top by tucking into a groove cut in the concrete and sealed
with a suitable mastic sealant.
The applied membranes shall be protected immediately from the ongoing site activities or from
sharp aggregates during backfilling with a tough, weather, warp and rot proof asphaltic protection
board (BITUBOARD) of suitable thickness.
When used as a flashing membrane on up-stands and parapets, BITUSTICK AL membrane will be
lapped with the base membrane and taken up on the up-stand and tucked inside the groove cut
along the parapet wall. The tucked membrane will be sealed with a bitumen mastic sealant
(BITUMASTIC).
Fixing of Protection Board:

BITUBOARD can be fixed in place by the following methods:

Fixing by Double sided adhesive tape (WATERTITE TS 15): Peel off the anti stick PE film from
the underside of the protection board. Cut out 100mm-150mm lengths of the tape from the roll and
peel off the release film from one side of the tape. Stick these to the edges and centre of the
protection board at intervals. Peel off the release paper from the other side and fix the board on the
membrane. Provide supports/props to keep the boards in place till the adhesive is strong enough
to hold the board.
Fixing by Synthetic Rubber Adhesive (BITUBOND N): Peel off the anti-stick PE film from the
underside of the protection board. Apply the adhesive on various spots on the protection board.
Press the board immediately onto the substrate. Provide supports/props to keep the boards in
place till the adhesive is strong enough to hold the board.
Note: A point to be noted is that due to the absorption of heat in the concrete, the water present will try
to come out in the form of vapor, thus creating an upward pressure on the membrane. This leads to
the formation of bubbles. In order to minimize the formation of these bubbles it is always
recommended to cover up the membranes immediately after application (within 24 hours) with a
protection board or cement sand screed.
Bubble formation will not in any way affect the water proofing property of the membrane unless it is
physically damaged. However, it has to be ensured that the lap joints are properly sealed and does not
open up, as these will be the weak points for water penetration.
MS_Bitustick-AL_GCC_0917_GR0

Membrane around Pipes

A cement sand/mastic sealant angle fillet shall be provided all around the pipe joint. A 400 mm wide
reinforcing strip shall be applied after applying the primer. The joint of the membrane with the pipe
shall be sealed with a bitumen rubber mastic.

MEMBRANE REPAIR
In case of the BITUSTICK AL membrane getting punctured due to the ongoing site activities, the
following repair procedures shall be followed.
Minor pinhole of diameters less than 0.5mm will not affect the waterproofing properties of the
system, since the highly elastic SBS compound has a self-healing property and will tend to cover
and extend over the puncture and seal it.
Larger damages shall be patched repaired with a piece of the same membrane which extends at
least 100mm from all the sides of the puncture. The area to be repaired shall be primed with the
bitumen primer and allowed to dry before carrying out the patching works.
Safety Data Sheet according to Regulation (EC) No 1907/2006
Page 1 of 10
SDS No. : 574342
BITUSTICK AL V001.0
Revision: 26.01.2018
printing date: 23.09.2020
Replaces version from: -

SECTION 1: Identification of the substance/mixture and of the company/undertaking

1.1. Product identifier
BITUSTICK AL
1.2. Relevant identified uses of the substance or mixture and uses advised against
Intended use:
Bituminous product

1.3. Details of the supplier of the safety data sheet

Henkel Jebel Ali FZCo.
Block F, Dubai Silicon Oasis HQ
PO BOX 341044
Dubai

Utd.Arab.Emir.

[email protected]

1.4. Emergency telephone number

HAAD Poison and Drug Information Center UAE, TOLL FREE TEL. NUMBER 800-424

SECTION 2: Hazards identification

2.1. Classification of the substance or mixture

Classification (CLP):
Substances and preparations marketed in a specific form or within specific containers need not to be classified according to
the REACH Regulation Article 3 (3).

2.2. Label elements

Label elements (CLP):

Substances and preparations marketed in a specific form or within specific containers need not to be classified according to
the REACH Regulation Article 3 (3).

2.3. Other hazards

None if used properly.
Not fulfilling Persistent, Bioaccumulative and Toxic (PBT), very Persistent and very Bioaccumulative (vPvB) criteria.
MSDS-No.: 574342 BITUSTICK AL Page 2 of 10
V001.0

SECTION 3: Composition/information on ingredients

3.2. Mixtures

General chemical description:

Manufactured item - article
Base substances of preparation:
Bitumen
Mineral fillers

Declaration of the ingredients according to CLP (EC) No 1272/2008:

Contains no dangerous substances exceeding the limits of the EU-Regulation

SECTION 4: First aid measures

4.1. Description of first aid measures

General information:
In case of adverse health effects seek medical advice.

Inhalation:
Move to fresh air, consult doctor if complaint persists.

Skin contact:
Rinse with running water and soap. Apply replenishing cream. Change all contaminated clothing.

Eye contact:
Rinse immediately with plenty of running water, seek medical advice if necessary.

Ingestion:
Rinse mouth and throat. Drink 1-2 glasses of water. Seek medical advice.

4.2. Most important symptoms and effects, both acute and delayed
No data available.

4.3. Indication of any immediate medical attention and special treatment needed
See section: Description of first aid measures

SECTION 5: Firefighting measures

5.1. Extinguishing media

Suitable extinguishing media:
carbon dioxide, foam, powder, water spray jet, fine water spray

Extinguishing media which must not be used for safety reasons:

High pressure waterjet

5.2. Special hazards arising from the substance or mixture

In the event of a fire, carbon monoxide (CO) and carbon dioxide (CO2) can be released.
5.3. Advice for firefighters
Wear self-contained breathing apparatus.
Wear protective equipment.

SECTION 6: Accidental release measures

6.1. Personal precautions, protective equipment and emergency procedures

Wear protective equipment.

6.2. Environmental precautions

Do not empty into drains / surface water / ground water.
MSDS-No.: 574342 BITUSTICK AL Page 3 of 10
V001.0

6.3. Methods and material for containment and cleaning up

Remove mechanically.
Dispose of contaminated material as waste according to Section 13.

6.4. Reference to other sections

See advice in section 8

SECTION 7: Handling and storage

7.1. Precautions for safe handling
No particular measures required.

Hygiene measures:
Wash hands before work breaks and after finishing work.
Do not eat, drink or smoke while working.

7.2. Conditions for safe storage, including any incompatibilities

Keep away from heat and direct sunlight.
Do not store together with food or other consumables (coffee, tea, tobacco, etc.).

7.3. Specific end use(s)

Bituminous product
MSDS-No.: 574342 BITUSTICK AL Page 4 of 10
V001.0

SECTION 8: Exposure controls/personal protection

8.1. Control parameters

Occupational Exposure Limits

Valid for
Utd.Arab.Emir.

Ingredient [Regulated substance] ppm mg/m3 Value type Short term exposure limit Regulatory list
category / Remarks
Asphalt 0,5 Time Weighted Average AD TLV
8052-42-4 (TWA):
[ASPHALT (BITUMEN) FUME AS
BENZENE-SOLUBLE AEROSOL,
INHALABLE FRACTION OF THE
AEROSOL]
Asphalt 5 Time Weighted Average GCC TLV
8052-42-4 (TWA):
[ASPHALT (FUMES)]
Asphalt 5 Time Weighted Average UAE OEL
8052-42-4 (TWA):
[ASPHALT (FUMES)]
Asphalt 5 Time Weighted Average DB OEL
8052-42-4 (TWA):
[ASPHALT (FUMES)]
Calcium carbonate 10 Time Weighted Average DB OEL
471-34-1 (TWA):
[CALCIUM CARBONATE, INHALABLE
DUST]
Calcium carbonate 4 Time Weighted Average DB OEL
471-34-1 (TWA):
[MARBLE, RESPIRABLE
LIMESTONE, RESPIRABLE]
Calcium carbonate 4 Time Weighted Average DB OEL
471-34-1 (TWA):
[CALCIUM CARBONATE, RESPIRABLE
DUST]
Calcium carbonate 10 Time Weighted Average DB OEL
471-34-1 (TWA):
[MARBLE, TOTAL INHALABLE
LIMESTONE, TOTAL INHALABLE]
Distillates (petroleum), solvent-refined 0,2 Time Weighted Average AD TLV
heavy paraffinic (TWA):
64741-88-4
[OIL MIST, MINERAL]
Distillates (petroleum), solvent-refined 5 Time Weighted Average AD TLV
heavy paraffinic (TWA):
64741-88-4
[MINERAL OIL, PURE, INHALABLE
FRACTION OF THE AEROSOL
MINERAL OIL, HIGHLY AND
SEVERELY REFINED, INHALABLE
FRACTION OF THE AEROSOL]
Polyethylene 10 Time Weighted Average DB OEL
9002-88-4 (TWA):
[DUST, INHALABLE DUST]
Polyethylene 4 Time Weighted Average DB OEL
9002-88-4 (TWA):
[DUST, RESPIRABLE DUST]
MSDS-No.: 574342 BITUSTICK AL Page 5 of 10
V001.0

Occupational Exposure Limits

Valid for
Bharain

Ingredient [Regulated substance] ppm mg/m3 Value type Short term exposure limit Regulatory list
category / Remarks
Asphalt 5 Time Weighted Average BH TLV
8052-42-4 (TWA):
[ASPHALT (FUMES)]
Asphalt 5 Time Weighted Average GCC TLV
8052-42-4 (TWA):
[ASPHALT (FUMES)]

Occupational Exposure Limits

Valid for
Egypt

Ingredient [Regulated substance] ppm mg/m3 Value type Short term exposure limit Regulatory list
category / Remarks
Asphalt 0,5 Time Weighted Average EG OEL
8052-42-4 (TWA):
[ASPHALT (PETROLEUM) FUMES ( AS
BENZENE SOLUBLE AEROSOLS)]
Calcium carbonate 10 Time Weighted Average EG OEL
471-34-1 (TWA):
[CALCIUM CARBONATE (INCLUDING
LIMESTONE AND MARBLE), TOTAL
DUST CONTAINING NO MORE THAN
1% CRYSTALLIZED SILICA AND NO
ASBESTOS]
Distillates (petroleum), solvent-refined 5 Time Weighted Average EG OEL
heavy paraffinic (TWA):
64741-88-4
[MINERAL OIL MIST (EXCEPT
IRRITANT OIL)]
Distillates (petroleum), solvent-refined 10 Short-term Exposure Limit EG OEL
heavy paraffinic (STEL):
64741-88-4
[MINERAL OIL MIST (EXCEPT
IRRITANT OIL)]
Polyethylene 10 Time Weighted Average EG OEL
9002-88-4 (TWA):
[DUSTS (NOT OTHERWISE SPECIFIED)
CONTAINING LESS THAN 1% QUARTZ,
TOTAL DUST]
Polyethylene 3 Time Weighted Average EG OEL
9002-88-4 (TWA):
[DUSTS (NOT OTHERWISE SPECIFIED)
CONTAINING LESS THAN 1% QUARTZ,
INHALABLE DUST]

Occupational Exposure Limits

Valid for
Jordan

Ingredient [Regulated substance] ppm mg/m3 Value type Short term exposure limit Regulatory list
category / Remarks
Asphalt 5 Time Weighted Average JO TLV
8052-42-4 (TWA):
[ASPHALT]

Occupational Exposure Limits

Valid for
Kuwait
MSDS-No.: 574342 BITUSTICK AL Page 6 of 10
V001.0

Ingredient [Regulated substance] ppm mg/m3 Value type Short term exposure limit Regulatory list
category / Remarks
Asphalt 5 Time Weighted Average GCC TLV
8052-42-4 (TWA):
[ASPHALT (FUMES)]
Asphalt 5 Short-term Exposure Limit KW OEL
8052-42-4 (STEL):
[ASPHALT (FUME)]
Asphalt Harmful Concentration for Unknown KW OEL
8052-42-4 risk to health and life:
[ASPHALT (FUME)]
Calcium carbonate 10 Time Weighted Average KW OEL
471-34-1 (TWA):
[MARBLE (CALCIUM CARBONATE),
TOTAL]
Calcium carbonate 5 Time Weighted Average KW OEL
471-34-1 (TWA):
[MARBLE (CALCIUM CARBONATE),
INHALED]
Calcium carbonate Harmful Concentration for Unknown KW OEL
471-34-1 risk to health and life:
[MARBLE (CALCIUM CARBONATE),
INHALED]
Calcium carbonate Harmful Concentration for Unknown KW OEL
471-34-1 risk to health and life:
[MARBLE (CALCIUM CARBONATE),
TOTAL]
Polyethylene Harmful Concentration for Unknown KW OEL
9002-88-4 risk to health and life:
[PARTICULATES, INHALED]
Polyethylene 15 Time Weighted Average KW OEL
9002-88-4 (TWA):
[PARTICULATES, TOTAL]
Polyethylene Harmful Concentration for Unknown KW OEL
9002-88-4 risk to health and life:
[PARTICULATES, TOTAL]
Polyethylene 5 Time Weighted Average KW OEL
9002-88-4 (TWA):
[PARTICULATES, INHALED]

Occupational Exposure Limits

Valid for
Israel

Ingredient [Regulated substance] ppm mg/m3 Value type Short term exposure limit Regulatory list
category / Remarks
Asphalt 0,5 Time Weighted Average IL OEL
8052-42-4 (TWA):
[ASPHALT (BITUMEN) FUME, AS
BENZENE-SOLUBLE AEROSOL,
INHALABLE FRACTION]
Distillates (petroleum), solvent-refined 5 Time Weighted Average IL OEL
heavy paraffinic (TWA):
64741-88-4
[MINERAL OIL, EXCLUDING METAL
WORKING FLUIDS, PURE, HIGHLY
AND SEVERELY REFINED,
INHALABLE FRACTION]
Polyethylene 10 Time Weighted Average IL OEL
9002-88-4 (TWA):
[PARTICLES (INSOLUBLE OR POORLY
SOLUBLE) NOT OTHERWISE
SPECIFIED, INHALABLE PARTICLES]
Polyethylene 3 Time Weighted Average IL OEL
9002-88-4 (TWA):
[PARTICLES (INSOLUBLE OR POORLY
SOLUBLE) NOT OTHERWISE
SPECIFIED, RESPIRABLE PARTICLES]

Occupational Exposure Limits

Valid for
MSDS-No.: 574342 BITUSTICK AL Page 7 of 10
V001.0

Kenya

Ingredient [Regulated substance] ppm mg/m3 Value type Short term exposure limit Regulatory list
category / Remarks
Asphalt 5 Time-weighted average KE OEL-RL
8052-42-4 (TWA) OEL-RL:
[ASPHALT, PETROLEUM FUMES]
Asphalt 10 Short-term OEL-RL: KE OEL-RL
8052-42-4
[ASPHALT, PETROLEUM FUMES]
Calcium carbonate 5 Time-weighted average KE OEL-RL
471-34-1 (TWA) OEL-RL:
[MARBLE RESPIRABLE DUST
CALCIUM CARBONATE RESPIRABLE
DUST
LIMESTONE RESPIRABLE DUST]
Calcium carbonate 10 Time-weighted average KE OEL-RL
471-34-1 (TWA) OEL-RL:
[MARBLE TOTAL INHALABLE DUST
LIMESTONE TOTAL INHALABLE DUST
CALCIUM CARBONATE TOTAL
INHALABLE DUST]

Biological Exposure Indices:

None

8.2. Exposure controls:

Respiratory protection:
Not needed.

Hand protection:
Not needed.

Eye protection:
Not needed.

SECTION 9: Physical and chemical properties

9.1. Information on basic physical and chemical properties
Appearance Roll
solid
dark
Odor characteristic
Odour threshold No data available / Not applicable

pH No data available / Not applicable

Initial boiling point > 300 °C (> 572 °F)
Flash point Not applicable
Decomposition temperature No data available / Not applicable
Vapour pressure No data available / Not applicable
Density 1,02 - 1,03 g/cm3
(25 °C (77 °F))
Bulk density No data available / Not applicable
Viscosity No data available / Not applicable
Viscosity (kinematic) No data available / Not applicable
Explosive properties No data available / Not applicable
Solubility (qualitative) No data available / Not applicable
Solidification temperature No data available / Not applicable
Melting point > 105 °C (> 221 °F)
Flammability No data available / Not applicable
Auto-ignition temperature No data available / Not applicable
Explosive limits No data available / Not applicable
Partition coefficient: n-octanol/water No data available / Not applicable
Evaporation rate No data available / Not applicable
Vapor density No data available / Not applicable
MSDS-No.: 574342 BITUSTICK AL Page 8 of 10
V001.0

Oxidising properties No data available / Not applicable

9.2. Other information

No data available / Not applicable

SECTION 10: Stability and reactivity

10.1. Reactivity
Reaction with acids: production of heat and carbon dioxide.

10.2. Chemical stability

Stable under recommended storage conditions.

10.3. Possibility of hazardous reactions

See section reactivity

10.4. Conditions to avoid

None if used for intended purpose.

10.5. Incompatible materials

See section reactivity.

10.6. Hazardous decomposition products

None known.

SECTION 11: Toxicological information

11.1. Information on toxicological effects

General toxicological information:

To the best of our knowledge no harmful effects are to be expected if the product is handled and used properly.

SECTION 12: Ecological information

General ecological information:
Do not empty into drains, soil or bodies of water.

12.1. Toxicity

No data available.

12.2. Persistence and degradability

No data available.

12.3. Bioaccumulative potential / 12.4. Mobility in soil

No data available.

12.5. Results of PBT and vPvB assessment

No data available.

12.6. Other adverse effects

No data available.
MSDS-No.: 574342 BITUSTICK AL Page 9 of 10
V001.0

SECTION 13: Disposal considerations

13.1. Waste treatment methods
Product disposal:
Dispose of waste and residues in accordance with local authority requirements.

Disposal of uncleaned packages:

Use packages for recycling only when totally empty.

Waste code
080499

SECTION 14: Transport information

14.1. UN number

Not hazardous according to RID, ADR, ADN, IMDG, IATA-DGR.

14.2. UN proper shipping name

Not hazardous according to RID, ADR, ADN, IMDG, IATA-DGR.

14.3. Transport hazard class(es)

Not hazardous according to RID, ADR, ADN, IMDG, IATA-DGR.

14.4. Packing group

Not hazardous according to RID, ADR, ADN, IMDG, IATA-DGR.

14.5. Environmental hazards

Not hazardous according to RID, ADR, ADN, IMDG, IATA-DGR.

14.6. Special precautions for user

Not hazardous according to RID, ADR, ADN, IMDG, IATA-DGR.

14.7. Transport in bulk according to Annex II of Marpol and the IBC Code

not applicable

SECTION 15: Regulatory information

15.1. Safety, health and environmental regulations/legislation specific for the substance or mixture

VOC content 0%
(VOCV 814.018 VOC regulation
CH)

15.2. Chemical safety assessment

A chemical safety assessment has not been carried out.

SECTION 16: Other information

MSDS-No.: 574342 BITUSTICK AL Page 10 of 10
V001.0

Further information:
This information is based on our current level of knowledge and relates to the product in the state in which it is delivered. It is
intended to describe our products from the point of view of safety requirements and is not intended to guarantee any
particular properties.
The product is intended for industrial use.

Relevant changes in this safety data sheet are indicated by vertical lines at the left margin in the body of this document.
Corresponding text is displayed in a different color on shadowed fields.
 REPORT ON DETERMINATION OF SOFTENING POINT OF SELF
ADHESIVE WATERPROOFING MEMBRANE
Page 1 of 1

Contractor : Henkel Polybit Industries Limited Report No. : WPR-2211/730

Address : P.O. Box: 293, Umm Al Quwain, UAE Lab. Project No. : P-675

Client : NP Lab Ref. No. : WPQ-2211/380

Consultant : NP Date Sample Received : 04/11/2022

Project Name : NP Date test started : 08/11/2022

Size of Sample : 1x2 m Date test completed : 08/11/2022

Sample Description : Aluminium Surfaced Solar Report Date : 21/11/2022

Reflective Waterproofing
Membrane Testing Temperature : 24 oC

Sample Name : Bitustick AL Reagent used for softening point : Ethylene Glycol

Marking on Sample : NP Apparatus Used : Ring & Balls

Manufacturer/Source : Henkel Polybit Temperature of preheat before testing : 30 ºC

Date of sampling : 04/11/2022 Weight & Diameter of steel balls : 3.5 g & 9.5mm dia

Sender's Ref. No. : HPIL/MLD/040/2022 Sample Brought in by : Client

Sampled by : Client Tested by : AJI

Test Data

Softening Point (Test Method ASTM D 36-2000) 117OC

Method variation : None

Remarks : None

Authorized Signatory
Results relate only to the item tested.
This report shall not be reproduced except in full, without written approval of the laboratory.
 REPORT ON TEAR STRENGTH OF FILM
Page 1 of 1

Client : Henkel Polybit Industries Limited Report No : WPR-2211/731

Address : P.O. Box: 293, Umm Al Quwain, UAE Lab Project No : P-675

Contractor : NP Lab Ref. No. : WPQ-2211/380

Consultant : NP Date of Sampling : 04/11/2022

Project Name : NP Date sample received : 04/11/2022

Sample Description : Aluminium Surfaced Solar Date test started : 10/11/2022

Reflective Waterproofing
Membrane Date test completed : 10/11/2022
Bitustick AL-
Sample Name : Report Date : 21/11/2022
Film
Marking on sample : NP Size of Sample : 1x2 m

Manufacturer/Source : Henkel Polybit Room Temperature : 24ºC

Sender's Ref. No. : HPIL/MLD/040/2022 Relative humidity : 50%

Sampled by : Client Sample brought in by : Client

Type of Machine used : Universal Testing Machine Tested by : AJI

Test Data
Tear Strength thickness
Width Thickness Transverse
Lab Ref. No. Longitudinal Longitudinal Transverse
(mm) (mm) ( N/mm)
(N) ( N/mm) Thickness (N)
Thickness

WPQ-2211/380/1 15.0 0.10 23.5 235 23.7 237

WPQ-2211/380/2 15.0 0.10 22.8 228 23.4 234

WPQ-2211/380/3 15.0 0.10 22.7 227 22.9 229

WPQ-2211/380/4 15.0 0.10 25.6 256 22.7 227

WPQ-2211/380/5 15.0 0.10 24.0 240 22.5 225

Average = 24 237 23.0 230

Standard Deviation= 1.178 11.777 0.498 4.980

Tear Strength Test Method : ASTM D 1004- 94a

Conditioning of specimen : ASTM D 1004- 94a Cls. 6.1
Method variation : None
Remarks : None

Results relate only to the item tested.

This report shall not be reproduced except in full, without written approval of the laboratory.
Authorized Signatory
 REPORT ON ADHESION STRENGTH TO SELF OF SELF ADHESIVE
WATERPROOFING MEMBRANE
Page 1 of 1

Client : Henkel Polybit Industries Limited Report No. : WPR-2211/732/1

Address : P.O. Box: 293, Umm Al Quwain, UAE Lab. Project No. : P-675

Contractor : NP Lab Ref. No. : WPQ-2211/380

Consultant : NP Date of Sampling : 04/11/2022

Project Name : NP Date Sample Received : 04/11/2022

Sample Description : Aluminium Surfaced Solar Date test started : 10/11/2022

Reflective Waterproofing
Membrane Date test completed : 10/11/2022

Sample Name : Bitustick AL Report Date : 21/11/2022

Source of sample : Henkel Polybit Testing Temperature : 24ºC

Machine Used : Universal Testing Machine Speed of machine : 300 mm/min

Sender's Ref. No. : HPIL/MLD/040/2022 Sample Brought in by : Client

Sampled by : Client Tested by : AJI

Test Data :

Length of Width of
Thickness Maximum Adhesion
Lab Ref. No. Bonded Bonded Area
(mm) Load (N) Strength (N/mm)
Area (mm) (mm)

WPQ-2211/380/1 100.0 25.0 1.50 56.32 2.253

WPQ-2211/380/2 100.0 25.0 1.50 64.18 2.567

WPQ-2211/380/3 100.0 25.0 1.50 56.06 2.242

Average= 58.85 2.354

Maximum= 64.18 2.567

Minimum= 56.06 2.242

Test Method : ASTM D 1000 : Section 46-50: 1999

Test Method Variation : None
Remarks : None

Results relate only to the item tested. Authorized Signatory

This report shall not be reproduced except in full without written approval of the laboratory.
 REPORT ON ADHESION STRENGTH OF SELF ADHESIVE WATERPROOFING
MEMBRANE TO PRIMED CONCRETE
Page 1 of 1

Client : Henkel Polybit Industries Limited Report No. : WPR-2211/732/2

Address : P.O. Box: 293, Umm Al Quwain, UAE Lab. Project No. : P-675

Contractor : NP Lab Ref. No. : WPQ-2211/380

Consultant : NP Date of Sampling : 04/11/2022

Project Name : NP Date Sample Received : 04/11/2022

Sample Description : Aluminium Surfaced Solar Date test started : 10/11/2022

Reflective Waterproofing
Membrane Date test completed : 10/11/2022

Sample Name : Bitustick AL Report Date : 21/11/2022

Source of sample : Henkel Polybit Testing Temperature : 24ºC

Machine Used : Universal Testing Machine Speed of machine : 300 mm/min

Sender's Ref. No. : HPIL/MLD/040/2022 Sample Brought in by : Client

Sampled by : Client Tested by : AJI

Test Data :

Length of Width of
Thickness Maximum Adhesion
Lab Ref. No. Bonded Bonded Area
(mm) Load (N) Strength (N/mm)
Area (mm) (mm)

WPQ-2211/380/1 100.0 25.0 1.50 82.00 3.280

WPQ-2211/380/2 100.0 25.0 1.50 89.00 3.560

WPQ-2211/380/3 100.0 25.0 1.50 87.00 3.480

Average= 86.00 3.440

Maximum= 89.00 3.560

Minimum= 82.00 3.280

Test Method : ASTM D 1000 : Section 46-50: 1999

Test Method Variation : None
Remarks : None

Results relate only to the item tested. Authorized Signatory

This report shall not be reproduced except in full without written approval of the laboratory.
 REPORT ON TENSILE STRENGTH AND ELONGATION OF FILM
Page 1 of 1

Client : Henkel Polybit Industries Limited Report No : WPR-2211/733/1

Address : P.O. Box: 293, Umm Al Quwain, UAE Lab Project No : P-675

Contractor : NP Lab Ref. No. : WPQ-2211/380

Consultant : NP Date of Sampling : 04/11/2022

Project Name : NP Date Sample Received : 04/11/2022

Sample Description : Aluminium Surfaced Solar Reflective Date test started : 11/11/2022
Waterproofing Membrane Date test completed : 11/11/2022

Sample Name : Bitustick AL- Film Report Date : 21/11/2022

Manufacturer/Source : Henkel Polybit Size of Sample : 1x2 m

Sample brought in by : : Client Sender's Ref. No. : HPIL/MLD/040/2022

Sampled by : Client Tested by : AJI

Gauge Length : 50 mm Specimen Type : Straight Specimen

Speed of Testing : 500 mm/ min. Testing Room Temperature : 23 ± 2 oC

Direction of test : Longitudinal Relative humidity : 50%

Test Data

Length of Width of Maximum Tensile

Thickness Elongation at Break
Lab Ref. No. Specimmen Specimen Load Strength
(mm) (%)
(mm) (mm) (N) (MPa)

WPQ-2211/380/1 150 0.10 25.0 100.7 40.28 246

WPQ-2211/380/2 150 0.10 25.0 112.0 44.80 243

WPQ-2211/380/3 150 0.10 25.0 114.0 45.60 214

WPQ-2211/380/4 150 0.10 25.0 101.2 40.48 212

WPQ-2211/380/5 150 0.10 25.0 113.0 45.20 235

Average = 43.27 230

Test Method : ASTM D 882-97

Conditioning of specimen : ASTM D 882-97 Section. 7.1
Method variation : None
Remarks : This test was carried out using a computerized universal testing machine (UTM-5).

Results relate only to the item tested.

This report shall not be reproduced except in full, without written approval of the laboratory.
Authorized Signatory
 REPORT ON TENSILE STRENGTH AND ELONGATION OF FILM
Page 1 of 1

Client : Henkel Polybit Industries Limited Report No : WPR-2211/733/2

Address : P.O. Box: 293, Umm Al Quwain, UAE Lab Project No : P-675

Contractor : NP Lab Ref. No. : WPQ-2211/380

Consultant : NP Date of Sampling : 04/11/2022

Project Name : NP Date Sample Received : 04/11/2022

Sample Description : Aluminium Surfaced Solar Reflective Date test started : 11/11/2022
Waterproofing Membrane Date test completed : 11/11/2022

Sample Name : Bitustick AL- Film Report Date : 21/11/2022

Manufacturer/Source : Henkel Polybit Size of Sample : 1x2 m

Sample brought in by : : Client Sender's Ref. No. : HPIL/MLD/040/2022

Sampled by : Client Tested by : AJI

Gauge Length : 50 mm Specimen Type : Straight Specimen

Speed of Testing : 500 mm/ min. Testing Room Temperature : 23 ± 2 oC

Direction of test : Transverse Relative humidity : 50%

Test Data

Length of Width of Maximum Tensile

Thickness Elongation at Break
Lab Ref. No. Specimmen Specimen Load Strength
(mm) (%)
(mm) (mm) (N) (MPa)

WPQ-2211/380/1 150 0.10 25.0 130.0 52.00 217

WPQ-2211/380/2 150 0.10 25.0 130.0 52.00 208

WPQ-2211/380/3 150 0.10 25.0 137.0 54.80 192

WPQ-2211/380/4 150 0.10 25.0 128.0 51.20 178

WPQ-2211/380/5 150 0.10 25.0 138.0 55.20 186

Average = 53.04 196

Test Method : ASTM D 882-97

Conditioning of specimen : ASTM D 882-97 Section. 7.1
Method variation : None
Remarks : This test was carried out using a computerized universal testing machine (UTM-5).

Results relate only to the item tested.

This report shall not be reproduced except in full, without written approval of the laboratory.
Authorized Signatory
 REPORT OF RESISTANCE TO PUNCTURE OF WATER VAPOUR RETARDERS USED
IN CONTACT WITH EARTH UNDER CONCRETE SLABS, ON WALLS, OR AS GROUND
COVER
Page 1 of 1

Client : Henkel Polybit Industries Limited Report No : WPR-2211/734

Address : P.O. Box: 293, Umm Al Quwain, UAE Lab Project No : P-675

Contractor : NP Lab Ref. No. : WPQ-2211/380

Consultant : NP Date of sampling : 04/11/2022

Project Name : NP Date Sample Received : 04/11/2022

Sample Description : Aluminium Surfaced Solar Reflective Date test started : 10/11/2022
Waterproofing Membrane Date test completed : 10/11/2022

Sample Name : Bitustick AL Report Date : 21/11/2022

Manufacturer/Source : Henkel Polybit Conditoining temperature : 23±1°C

Marking on sample : NP Relative humidity : 50±5°C

Sampled by : Client Testing room temperature : 23ºC

Sample Brought in by : Client Size of Specimen : 254 x 254 mm

Type of Machine Used : Universal Testing Machine Speed of Testing : 6.0mm/min

Size of Sample : 1x2 m Sender's Ref. No. : HPIL/MLD/040/2022

Diameter of Plunger : 25.0 mm Tested by : AJI

Test Results Data:

Maximum Load Deflection at maximum Load

Lab Ref. No. Type of failure of the sheet
(N) (mm)

WPQ-2211/380/1 283.4 59.1 Satisfactory

WPQ-2211/380/2 265.2 55.2 Satisfactory

WPQ-2211/380/3 264.1 56.6 Satisfactory

Average = 270.9 57.0

Test Method : ASTM E 154/E154M-08a (Reapproved 2019): Section 10

Method variation : None

Remarks : None

Authorized Signatory

R-CSW-RP-01
Results relate only to the item tested. Issued on:08/02/2016
This report shall not be reproduced except in full, without written approval of the laboratory. Issue 01
 REPORT ON LOW TEMPERATURE FLEXIBILITY OF SELF ADHESIVE WATERPROOFING
MEMBRANE
Page 1 of 1

Client : Henkel Polybit Industries Limited Report No. : WPR-2211/736

Address : P.O. Box: 293, Umm Al Quwain, UAE Lab. Project No. : P-675

Contractor : NP Lab Ref. No.. : WPQ-2211/380

Consultant : NP Date of sampling : 04/11/2022

Project Name : NP Date Sample Received : 04/11/2022

Size of Sample : 1x2m Date test started : 10/11/2022

Sample Name : Bitustick AL Date test completed : 10/11/2022

Sample Description : Aluminium Surfaced Solar Report Date : 21/11/2022

Reflective Waterproofing
Membrane Conditioning Temperature : 24ºC

Source of sample : Client Required temperature : -15ºC

Sample Brought in by : Client Tested by : AJI

Sampled by : Client

Size of specimen : 150.0 x 25.0 mm

Client’s Ref. No. : HPIL/MLD/040/2022

Test Data

Flexibility at low temperature.

Cold Bend Behaviour at -15°C No cracks were observed on the samples.

Conditioning Method : ASTM D1970/D1970M-21

Method variation : None

Remarks : None

Authorized Signatory

Results relate only to the item tested.

This report shall not be reproduced except in full, without written approval of the laboratory.
 REPORT ON WATER ABSORPTION OF PLASTICS
Page 1 of 1

Client : Henkel Polybit Industries Limited Report No. : WPR-2211/737

Address : P.O. Box: 293, Umm Al Quwain, UAE Lab. Project No : P-675

Contractor : NP Lab Ref. No. : WPQ-2211/380

Consultant : NP Sampled by : Client

Project : NP Sample brought in by : Client

Project No. : NP Date of Sampling : 04/11/2022

Sample Description : Aluminium Surfaced Solar Date sample received : 04/11/2022

Reflective Waterproofing
Membrane Date test started : 10/11/2022

Sample Name : Bitustick AL- Film Date test completed : 11/11/2022

Manufacturer/Source : Henkel Polybit Report Date : 21/11/2022

Sample Size : 1x2m Average dimension of specimen (mm) : 76 x 25

Conditioning time : 24 Hours Conditioning Temperature : 23ºC

Time of immersion : 24 Hours Solvent Used : Distilled water

Sender's Ref. No. : HPIL/MLD/040/2022 Tested by : AJI

Test Data:

Lab Ref. No. WPQ-2211/380/1 WPQ-2211/380/2 WPQ-2211/380/3

Water Absorption (%) 0.02 0.01 0.01

Average Water Absorption (%) 0.01

Test Method : ASTM D570-98 (Reapproved 2018)

Immersion Procedure : ASTM D570-98 (Reapproved 2018) Cl. 7.1

Method variation : None

Remarks : Specimens were conditioned for 24 hours @ 23ºC.

Authorized Signatory

R-WA-P-01
Results relate only to the item tested. Issued on:08/02/2016
This report shall not be reproduced except in full, without written approval of the laboratory. Issue 01
 ‫التاريخ‪2022/01/24 :‬م‬
‫املرجع‪11/122/2022 :‬‬

‫املحترمين ‪،،،‬‬ ‫السادة‪ /‬شركة هنيكل بولي للصناعات املحدودة‬

‫السالم عليكم ورحمة هللا وبركاته‬

‫املوضوع‪ :‬طلب تسجيل مورد‬
‫تتقدم بلدية مدينة الشارقة لكم بأطيب التحيات وأرق األمنيات بدوام ّ‬
‫التقدم واالزدهار‪.‬‬ ‫ّ‬
‫بالشارة إلى املوضوع أعاله‪ ،‬وإلى الطلب الوارد إلينا بكتابكم املؤرخ في ‪2021/11/18‬م بشأن التأهيل املسبق لشركتكم‪ ،‬يرجى العلم بأنه‬
‫بعد مراجعة الفريق الفني املختص للطلب املقدم من قبلكم بشأن املوافقة على اعتماد شركتكم كمورد؛ فإنه قد تم اعتماد شركتكم‬
‫كمورد مؤهل لدى بلدية مدينة الشارقة لتوريد املواد الخاصة بأنظمة العزل املائي وكيماويات مواد البناء في مشاريع بلدية مدينة‬
‫الشارقة‪ ،‬علية يرجى مراجعة إدارة العقود واملشتريات ببلدية مدينة الشارقة لتسجيل شركتكم املوقرة‪.‬‬

‫كما يرجى العلم بأن بلدية مدينة الشارقة لن تتحمل مسؤولية أي عواقب تترتب على هذه املوافقة‪ ،‬عليه يجب التحقق من كل تقديم أو‬
‫مقترح ملشروع قبل مباشرة مواصفات كل مشروع‪.‬‬

‫هذا للتكرم بالعلم وإجراءاتكم‪.‬‬

‫ملزيد من االستفسارات‪ ،‬التواصل مع املهندس‪ /‬بالل جوس رقم هاتف (‪ )05516600020‬بإدارة الصرف الصحي‬

‫وتفضلوا بقبول فائق الحترام والتقدير‪،‬‬

‫ع ‪/‬عبيد سعيد الطنيجي‬

‫مديرعام بلدية مدينة الشارقة‬

‫‪-‬‬

‫‪Page 1 of 1‬‬ ‫]‪[Type here‬‬ ‫‪SCM-SUP-DOC-F-11-01‬‬

CONTRACT NO. : N-15907

PROJECT TITLE : Water Transmission Scheme from Taweelah to Ajban

CLIENT : Abu Dhabi Transmission & Despatch Company (TRANSCO)

CONTRACTOR : Hydropower Energy and General Construction

DOCUMENT – COMMENT SHEET – RESPONSE SHEET

Consultant Ref: N1 5 90 7 - PI L - T RA- O T- 06 5 3 Date Issued: 15-08-2021

Comment Sheet Ref: N1 5 90 7 - DC S- MA T - C I V - 26 9 R e v . 3 Date of Comment: 15-08-2021

Incoming Submittal Ref: N1 5 90 7 - HY D- T K- O L- 1 15 7 Date of Receipt: 11-08-2021

Document / Drawing Number Rev P Document Title QTY

Material Submittal for Roof Waterproofing
N15907-GE-MAT/C00-CN-S020-03 03 1 System (Polyprime SB + Bitustick XL + Bitustick 1
AL)

P: PURPOSE CODES
0: For Distribution 1: Issued for Approval 2: Issued for Construction
3: Issued for Information 4: As Built

STATUS CODE:

X Approved Not Approved

Approved Except As Noted Not Subject to Approval

Please return copy of signed CS for receipt confirmation

Parsons International

Abu Dhabi Transmission and Despatch Company

(TRANSCO)

Page 1 of 4
 Industrial License

License Details
License Number 107

Trade Name HENKEL POLYBIT INDUSTRIES

LIMTED
Legal Form Limited Liability

Issue Date 22/04/1995

Expiry Date 07/12/2023
Registration No 3246
Main License No
Telephone 0508992003 Email [email protected]
Mobile 0508992003

Address Details
Lease Contract Number TC - 29962
Property Owner Ahmed Mohamed Salim
Almelaihi Al-Ali
Region Umm Thaob 7 7
Street undefined
Telephone 0508919999 Mobile 0508919999
P.O.Box 0000909 Email [email protected]

License Members

Share Role Nationality Name

. . .
51%
Partner United Arab Emirates Links Solstice Brokers L.L.C

49%
Partner Germany Henkel KGAA company

0%
Manager Netherlands HARM PETRUS ANTONIUS PETERS

This Document is Considered as Commercial Register

107 Print Date 11/11/2022

Payment Voucher No. PO - 75807

107

"http://ded-e.uaq.ae"

Page 1/2 TEL +971 6 7064000 * UMM AL QUAIN, UAE * P.O.BOX 1333 .
Activities
Retail Sale Of Cosmetics -
Caulking Compounds and Similar Manufacturing
Fire Extinguishing Materials Manufacturing
Cements Prepared Additives Manufacturing
Damp proofing and water proofing works Insulation
Contracting
Wholesale of Cleaners and Detergents Trading -
Beauty and Make-Up Preparations Manufacturing
Wholesale of Cosmetics and Trading -
Retai sale of Buildings Material -
Detergents & Disinfectants Manufacturing
Onshore and Offshore Oil and Gas Fields and Facilities
Services

This Document is Considered as Commercial Register

107 Print Date 11/11/2022

Payment Voucher No. PO - 75807

107

"http://ded-e.uaq.ae"

Page 2/2 TEL +971 6 7064000 * UMM AL QUAIN, UAE * P.O.BOX 1333 .
Commercial License ‫ﺭﺧـﺼــــــﺔ ﺗﺠﺎﺭﻳﺔ‬
Emerging Economic Establishment ‫ﻣﻨﺸــــﺄﺓ ﺍﻗﺘﺼـــﺎﺩﻳــــﺔ ﻧﺎﺷﺌـــــــﺔ‬

License No : CN-2803442 : ‫ﺭﻗﻢ ﺍﻟﺮﺧﺼﺔ‬

ADCCI No : 2604043 : ‫ﻋﻀﻮﻳﺔ ﺍﻟﻐﺮﻓﺔ‬
Establishment Card : 1034660 : ‫ﻭﺯﺍﺭﺓ ﺍﻟﻤﻮﺍﺭﺩ ﺍﻟﺒﺸﺮﻳﺔ ﻭﺍﻟﺘﻮﻃﻴﻦ‬
MOHRE ‫ﺑﻄﺎﻗﺔ ﺍﻟﻤﻨﺸﺄﺓ‬
Establishment Card : 600166 : ‫ﺍﻟﻬﻴﺌﺔ ﺍﻻﺗﺤﺎﺩﻳﺔ ﻟﻠﻬﻮﻳﺔ‬
ICA ‫ ﺑﻄﺎﻗﺔ ﺍﻟﻤﻨﺸﺄﺓ‬-‫ﻭﺍﻟﺠﻨﺴﻴﺔ‬
Legal Form : UAE Branch - Um Al Kwain ‫ ﺍﻡ ﺍﻟﻘﻴﻮﻳﻦ‬- ‫ ﻓﺮﻉ ﺍﻣﺎﺭﺍﺗﻴﺔ‬: ‫ﺍﻟﺸﻜﻞ ﺍﻟﻘﺎﻧﻮﻧﻲ‬
1 ‫ ﻓﺮﻉ ﺃﺑﻮ ﻇﺒﻲ‬- ‫ ﻫﻨﻴﻜﻞ ﺑﻮﻟﻲ ﺑﺖ ﻟﻠﺼﻨﺎﻋﺎﺕ ﺍﻟﻤﺤﺪﻭﺩﺓ‬: ‫ﺍﻹﺳﻢ ﺍﻟﺘﺠﺎﺭﻱ‬
Trade Name : HENKEL POLYBIT INDUSTRIES LIMTED - BRANCH OF ABU DHABI 1
Establishment Date : 19/06/2019 : ‫ﺗﺎﺭﻳﺦ ﺗﺄﺳﻴﺲ ﺍﻟﻤﻨﺸﺄﺓ‬
Issue Date : 22/05/2022 : ‫ﺗﺎﺭﻳﺦ ﺍﻹﺻﺪﺍﺭ‬
Expiry Date : 18/06/2023 : ‫ﺗﺎﺭﻳﺦ ﺍﻹﻧﺘﻬﺎﺀ‬

‫ﺍﻟﺼﻠﺔ‬ ‫ﺍﻟﺠﻨﺴﻴﺔ‬ ‫ ﺍﻟﺸﺮﻛﺎﺀ‬/ ‫ﺍﻟﻤﻼﻙ‬ ‫ﺍﻟﺮﻣﺰ‬

Role Nationality Owners / Partners No.
‫ﺷﺮﻳﻚ‬ ‫ﺍﻹﻣﺎﺭﺍﺕ ﺍﻟﻌﺮﺑﻴﺔ ﺍﻟﻤﺘﺤﺪﺓ‬ ‫ﻟﻴﻨﻜﺲ ﺳﻮﻟﻴﺴﺘﻴﺲ ﻟﻠﻮﺳﺎﻃﺔ ﺍﻟﺘﺠﺎﺭﻳﺔ ﺫ ﻡ ﻡ‬ 41757790
Partner United Arab Emirates LINKS SOLSTICE COMMERCIAL BROKERS L L C
‫ﺷﺮﻳﻚ‬ ‫ﺃﻟﻤﺎﻧﻴﺎ‬ ‫ﺷﺮﻛﺔ ﻫﻨﻴﻜﻞ ﻛﻲ ﺟﻲ ﺍﻳﻪ ﺍﻳﻪ‬ 41757791
Partner Germany HENKEL KGAA COMPANY
‫ﻣﺪﻳﺮ‬ ‫ﻫﻮﻟﻨﺪﺍ‬ ‫ﻫﺎﺭﻡ ﺑﻴﺘﺮﻭﺱ ﺍﻧﻄﻮﻧﻴﻮﺱ ﺑﻴﺘﺮﺯ‬ 41757792
Manager Netherlands HARM PETRUS ANTONIUS PETERS
Commercial Activities : : ‫ﺍﻷﻧﺸﻄﺔ ﺍﻟﺘﺠﺎﺭﻳﺔ‬
- Retail sale of flammable resistant paint ‫ ﺑﺎﻟﺘﺠﺰﺋﺔ‬- ‫ ﺑﻴﻊ ﺍﻟﻄﻼﺀﺍﺕ ﻭﺍﻟﺪﻫﺎﻧﺎﺕ ﺍﻟﻤﻘﺎﻭﻣﺔ ﻟﻠﺤﺮﻳﻖ‬-
- Industrial Cooperative Marketing ‫ ﺗﺴﻮﻳﻖ ﺗﻌﺎﻭﻧﻲ ﺻﻨﺎﻋﻲ‬-
- Retail Sale of Buildings Material ‫ ﺑﺎﻟﺘﺠﺰﺋﺔ‬- ‫ ﺑﻴﻊ ﻣﻮﺍﺩ ﺍﻟﺒﻨﺎﺀ‬-
- Installation of insulation materials in buildings and facilities ‫ ﺗﺮﻛﻴﺐ ﺍﻟﻤﻮﺍﺩ ﺍﻟﻌﺎﺯﻟﺔ ﻓﻲ ﺍﻷﺑﻨﻴﺔ ﻭﺍﻟﻤﻨﺸﺂﺕ‬-
Address : ‫ ﺍﻟﺴﻴﺪ ﺳﻤﻮ ﺍﻟﺸﻴﺦ ﻣﺤﻤﺪ ﺑﻦ ﺧﻠﻴﻔﺔ ﺑﻦ ﺯﺍﻳﺪ ﻭ ﺍﺧﺮﻳﻦ‬,‫ ﻣﺒﻨﻰ‬,~ : 0 ,3 ‫ ﺍﻳﻜﺎﺩ‬,‫ﻣﺼﻔﺢ ﺟﻨﻮﺏ‬ : ‫ﺍﻟﻌﻨﻮﺍﻥ‬

Onwani Address : : ‫ﺍﻟﻌﻨﻮﺍﻥ ﺍﻟﻤﻮﺣﺪ‬

www.adbc.gov.ae ‫ ﻟﻠﺘﺤﻘﻖ ﻣﻦ ﺻﺤﺔ ﺍﻟﺒﻴﺎﻧﺎﺕ ﺍﻟﻮﺍﺭﺩﺓ ﻓﻲ ﺍﻟﺮﺧﺼﺔ ﺑﺮﺟﺎﺀ ﺯﻳﺎﺭﺓ ﺍﻟﻤﻮﻗﻊ‬.‫ ﺃﺑﻮﻇﺒﻲ‬- ‫ﻭﺛﻴﻘﺔ ﻣﻌﺘﻤﺪﺓ ﻭﺻﺎﺩﺭﺓ ﺑﺪﻭﻥ ﺗﻮﻗﻴﻊ ﺃﻭ ﺧﺘﻢ ﻣﻦ ﺩﺍﺋﺮﺓ ﺍﻟﺘﻨﻤﻴﺔ ﺍﻹﻗﺘﺼﺎﺩﻳﺔ‬
Approved document issued without signature or stamp by the Department of Economic Development - Abu Dhabi. To verify the license kindly
visit www.adbc.gov.ae
Official Email : [email protected] : ‫ﺍﻟﺒﺮﻳﺪ ﺍﻹﻟﻜﺘﺮﻭﻧﻲ ﺍﻟﺮﺳﻤﻲ‬
Official Mobile : 971569992018 : ‫ﺭﻗﻢ ﺍﻟﺘﻮﺍﺻﻞ ﺍﻟﺮﺳﻤﻲ‬

*CR-4478863*
www.adbc.gov.ae
 INDUSTRIAL LICENSE ‫ﺭﺧﺼــﺔ ﺻﻨـﺎﻋﻴﺔ‬
License No IN-2004813 ‫ﺭﻗﻢ ﺍﻟﺮﺧﺼﺔ‬
Emerging Industrial Establishment ‫ﻣﻨﺸــــﺄﺓ ﺻﻨـــﺎﻋﻴــــــــﺔ ﻧﺎﺷﺌـــــــﺔ‬
License Status : Industrial Leader ‫ ﺭﻭﺍﺩ ﺍﻟﺼﻨﺎﻋﺔ‬: ‫ﺣﺎﻟﺔ ﺍﻟﺮﺧﺼﺔ‬

Legal Form : Limited Liability Company ‫ ﺷﺮﻛﺔ ﺫﺍﺕ ﻣﺴﺆﻭﻟﻴﺔ ﻣﺤﺪﻭﺩﺓ‬: ‫ﺍﻟﺸﻜﻞ ﺍﻟﻘﺎﻧﻮﻧﻲ‬
ADCCI No : : ‫ﻋﻀﻮﻳﺔ ﺍﻟﻐﺮﻓﺔ‬

First Issue Date 21/12/2021 : ‫ﺗﺎﺭﻳﺦ ﺃﻭﻝ ﺇﺻﺪﺍﺭ‬ Enviroment No. : ‫ﺍﻟﺮﻗﻢ ﺍﻟﺒﻴﺌﻲ‬
: :
Issue Date : 21/12/2022 : ‫ﺗﺎﺭﻳﺦ ﺍﻹﺻﺪﺍﺭ‬ FCR No. : - : ‫ﺍﻟﺴﺠﻞ ﺍﻟﻤﺮﻛﺰﻱ ﺍﻟﻤﻮﺣﺪ‬
Expiry Date : 20/12/2023 : ‫ﺗﺎﺭﻳﺦ ﺍﻹﻧﺘﻬﺎﺀ‬ Trade Name No. : TN-4241436 : ‫ﺭﻗﻢ ﺍﻹﺳﻢ ﺍﻟﺘﺠﺎﺭﻱ‬
2 ‫ ﻓﺮﻉ‬- ‫ﻫﻨﻴﻜﻞ ﺑﻮﻟﻲ ﺑﺖ ﻟﻠﺼﻨﺎﻋﺎﺕ ﺍﻟﻤﺤﺪﻭﺩﺓ ﺫ ﻡ ﻡ‬ : ‫ﺍﻹﺳﻢ ﺍﻟﺘﺠﺎﺭﻱ‬
Trade Name : Henkel Polybit Industries Limited - Branch Of Abu Dhabi 2

Location : ‫ ﻏﻴﺮ ﻣﺘﻄﻠﺐ‬- Not Required : ‫ﻣﻮﻗﻊ ﺍﻟﻤﻨﺸﺄﺓ‬

Owner(s) Partner(s) ‫ ﺍﻟﺸﺮﻛــــﺎﺀ‬/ ‫ﺍﺳﻢ ﺻﺎﺣﺐ ﺍﻟﻤﻨﺸﺄﺓ‬

‫ﻧﺴﺒﺔ ﺍﻟﺸﺮﺍﻛﺔ‬ ‫ﺍﻟﺼﻠﺔ‬ ‫ﺍﻟﺠﻨﺴﻴﺔ‬ ‫ ﺍﻟﺸﺮﻛــــﺎﺀ‬/ ‫ﺍﻟﻤــــﻼﻙ‬ #

Share (%) Role Nationality Owners / Partners
‫ﺷﺮﻳﻚ‬ ‫ﺍﻹﻣﺎﺭﺍﺕ ﺍﻟﻌﺮﺑﻴﺔ ﺍﻟﻤﺘﺤﺪﺓ‬ ‫ﻟﻴﻨﻜﺲ ﺳﻮﻟﻴﺴﺘﻴﺲ ﻟﻠﻮﺳﺎﻃﺔ ﺍﻟﺘﺠﺎﺭﻳﺔ‬
51.00 % 1
Partner United Arab Emirates Links Soltstice Commercial Brokers L.L.C
‫ﺷﺮﻳﻚ‬ ‫ﺃﻟﻤﺎﻧﻴﺎ‬ ‫ﺷﺮﻛﺔ ﻫﻨﻴﻜﻞ ﻛﻲ ﺟﻲ ﺍﻳﻪ ﺍﻳﻪ‬
49.00 % 2
Partner Germany Henkel Kgaa Company
‫ﻣﺪﻳﺮ‬ ‫ﻫﻮﻟﻨﺪﺍ‬ ‫ﻫﺎﺭﻡ ﺑﻴﺘﺮﻭﺱ ﺍﻧﻄﻮﻧﻴﻮﺱ ﺑﻴﺘﺮﺯ‬
0.00 % 3
Manager Netherlands Harm Petrus Antonius Peters
Activities ‫ﺍﻷﻧﺸــــﻄــﺔ‬
Activity ‫ﺍﻟﻨﺸﺎﻁ‬ #
1 Caulking Compounds and Similar Manufacturing ‫ﺻﻨﺎﻋﺔ ﻣﺮﻛﺒﺎﺕ ﺍﻟﺴﺪ ﺍﻟﻐﻴﺮ ﺣﺮﺍﺭﻱ ﻭﻣﺎ ﻳﻤﺎﺛﻠﻬﺎ‬ 1
2 Cements Prepared Additives Manufacturing ‫ﺻﻨﺎﻋﺔ ﺍﻹﺿﺎﻓﺎﺕ ﺍﻟﻤﺤﻀﺮﺓ ﻟﻸﺳﻤﻨﺖ‬ 2

‫ﺍﻟﺘﺮﺧﻴﺺ ﺻﺎﺩﺭ ﻣﻦ ﻗﺒﻞ ﺳﻠﻄﺔ ﺍﻟﺘﺮﺧﻴﺺ ﺍﻟﻤﺤﻠﻴﺔ ﻓﻲ ﺇﻣﺎﺭﺓ ﺃﺑﻮﻇﺒﻲ ﺧﺎﺭﺝ ﺍﻟﻤﻨﺎﻃﻖ ﺍﻟﺤﺮﺓ‬
The license is issued by the local licensing authority in the Emirate of Abu Dhabi outside the free zones

Offical Email ‫ﺍﻟﺒﺮﻳﺪ ﺍﻻﻟﻜﺘﺮﻭﻧﻲ ﺍﻟﺮﺳﻤﻲ‬

Offical Mobile Number ‫ﺭﻗﻢ ﺍﻟﻬﺎﺗﻒ ﺍﻟﻤﺘﺤﺮﻙ ﺍﻟﺮﺳﻤﻲ‬

IN-2004813 - 23/11/2022
Page1 of 2 TAHAQAQ ‫ﺗﺤﻘﻖ‬
www.idb.added.gov.ae
Henkel Polybit Industries Ltd.
PO Box: 293, Umm Al Quwain, UAE
Phone: +971 (6) 76 70 777
Fax: +971 (6) 76 70 197
[email protected]

Henkel Polybit Industries Ltd.

PO Box: 5911, Dammam - 31432
Industrial Area - II, Kingdom of Saudi Arabia
Phone: +966 13 808 4061 / 62
Fax: +966 13 812 1164
[email protected]

www.henkelpolybit.com