1-1-1H

ERRORS AND REMEDIAL MEASURES

●Composition of Error Code

Error Code indicated on the display constructed three meaning codes as follow.

EX: 10 00 01
1. Category Code 2. Location Code 3. Detail Code

● Details of Error Code

Check Points & Remedial
Error Code Category Set Conditions Cause of problem
Measures
Motor runs even after
10 00 01 Motor Stop Error -
stop command.
Remove foreign matter from
Note Jam
transport path. Check drive belt.
Brake failure Replace Brake (BRK).
Check connector for relay board
Wiring failure for Motor
(1MZ-007).
Driver or Motor
10 00 02 Motor Initial Abnormality Replace relay board.
Motor Driver failure Replace Motor Driver.
Motor failure Replace Motor
Separator Motor Replace board 1MZ-002 or
Main CPU Board failure
(THM) 1MZ-001.
10 00 03 Motor lower limit Abnormality
Same as code
Motor upper limit 10-00-02
10 00 04
Abnormality
Motor Adjustment Error
Remove foreign matter from
10 00 07 Adjusted data wasn’t in the Note Jam
transport path. Check drive belt.
range.
Motor Adjustment Error Same as code
10 00 08
Motor speed was too slow. 10-00-07
Motor Adjustment Error Same as code
10 00 09
Motor speed was too fast. 10-00-07
Check all sensor levels and
10 00 10 Adjustment did not
clean the sensor which is dirty.
All Motors Motor Adjustment Error complete within
Replace motor driver or Motor
10 00 11 specified time.
one by one.
Motor runs even after
11 00 01 Motor Stop Error -
stop command.
Check connector between
Encoder in Validator
Encoder and Validator.
failure
Replace Encoder Assy.
Check connector for Relay board
Main Motor Wiring failure for Motor
11 00 02 Motor Initial Abnormality (1MZ-006).
(MHM) Driver or Motor
Replace Relay board.
Motor Driver failure Replace Motor Driver.
Motor failure Replace Main Motor

*X in error code in this list will assign A to F on the display. It indicates sensor position when the plural
number of sensors are in the same line. “A” locates the most front side. The location goes back by
alphabetical order.
 1-1-2H
ERRORS AND REMEDIAL MEASURES

Check Points & Remedial

Error Code Category Set Conditions Cause of problem
Measures
11 00 02 Battery failure Replace Battery on 1MZ001.
Replace board 1MZ-002 or
Motor Initial Abnormality Main Board failure
1MZ-001.
Motor lower limit Same as code
11 00 03
Abnormality 11-00-02
Motor upper limit Same as code
11 00 04
Main Motor Abnormality 11-00-02
(MHM) Motor Adjustment Error
Remove foreign matter from
11 00 07 Adjusted data wasn’t in the Note Jam
transport path. Check drive belt.
range.
Motor Adjustment Error
11 00 08
Motor speed was too slow. Same as code
Motor Adjustment Error 11-00-07
11 00 09
Motor speed was too fast.
Motor Stop Error
Same as code
12 00 01 (Motor runs even after stop
11-00-07
command.)
Remove foreign matter from
Jam Note
transport path. Check drive belt.
Check connector for relay board
Wiring failure for Motor
(1MZ-007).
Driver or Motor
12 00 02 Replace relay board.
Motor Initial Abnormality Motor Driver failure Replace Motor Driver.
Motor failure Replace Motor
Pocket Transport
Motor 1 Replace board 1MZ-002 or
Main CPU Board failure
(SHM1) 1MZ-001.
Motor lower limit
12 00 03 Same as code 12-00-02
Abnormality
Motor upper limit Same as code
12 00 04
Abnormality 12-00-02
Motor Adjustment Error
Remove foreign matter from
12 00 07 Adjusted data wasn’t in the Note Jam
transport path. Check drive belt.
range.
Motor Adjustment Error
12 00 08 Same as code 12-00-07
Motor speed was too slow.
Motor Adjustment Error
12 00 09 Same as code 12-00-07
Motor speed was too fast.
Motor Stop Error
13 00 01 (Motor runs even after stop - -
command.)
Remove foreign matter from
Note Jam
transport path. Check drive belt.
Check connector for relay board
Wiring failure for Motor (1MZ-007).
Driver or Motor
Replace relay board.
13 00 02 Pocket Transport
Motor Initial Abnormality
Motor 2 Motor Driver failure Replace Motor Driver.
(SHM2)
Motor failure Replace Motor

Replace board 1MZ-002 or

Main CPU Board failure
1MZ-001.
Motor lower limit
13 00 03 Same as code 13-00-02
Abnormality
Motor upper limit
13 00 04 Same as code 13-00-02
Abnormality

*X in error code in this list will assign A to F on the display. It indicates sensor position when the plural
number of sensors are in the same line. “A” locates the most front side. The location goes back by
alphabetical order.
 1-1-3H
ERRORS AND REMEDIAL MEASURES
Check Points & Remedial
Error Code Category Set Conditions Cause of problem
Measures
Motor Adjustment Error Remove foreign matter from
Note Jam
13 00 07 Adjusted data wasn’t in the transport path. Check drive belt.
range. Battery failure Replace Battery on 1MZ001.
Pocket Transport Motor Adjustment Error
13 00 08 Motor 2 Motor speed did not reach Same as code 13-00-07
(SHM2) the lowest limit.
Motor Adjustment Error
13 00 09 Motor speed did not reach Same as code 13-00-07
the highest limit.
14 00 10 Drive Output Error 0
14 00 11 Drive Output Error 1
14 00 12 Drive Output Error 2 - -
14 00 13 Drive Output Error 31
14 00 14 Drive Output Error 32
ITU, ITB or ITD
NP Position Logic Error Check connector of sensors.
14 00 15 sensor failure. Wiring
when NP lifts up. Replace ITU, ITB or ITD sensor.
failure.
NP Position Logic Error
14 00 16
when NP falls down.
NP Position Logic Error
14 00 17 when NP lifts up according
Same as code 14-00-15
NP Start Sensor.
NP Position Logic Error
14 00 18 when NP falls down
according NP Start Sensor.
Time out due to blocking NP Check connection of BPM Motor
Note Press Drive Motor
14 00 19 Bottom Position when NP and Drive Board 1MZ002.
BPM failure.
lifts up. Replace Motor or Drive board.
Time out due to blocking NP
14 00 20 Upper Position check when
NP falls down.
Note Press (NP) Time out due to blocking NP
Bottom Position check when
14 00 21
NP lifts up according NP
Start Sensor.
Time out due to blocking NP
Upper Position check when
14 00 22
NP falls down according NP
Start Sensor.
Time out of reaching NP
14 00 23 Position check when NP lifts
Same as code 14-00-19
up.
Time out of reaching NP
14 00 24 Position check when NP falls
down.
Time out of reaching NP
upper position check when
14 00 25 NP lifts up according NP
start Sensor.

Time out of reaching NP

bottom position check when
14 00 26
NP falls down according NP
start Sensor.
Pocket Gate
15 00 00 Solenoid 1 - -
(PKG1)
Gate Position Abnormality
Pocket Gate
16 00 00 Solenoid 2 - -
(PKG2)

*X in error code in this list will assign A to F on the display. It indicates sensor position when the plural
number of sensors are in the same line. “A” locates the most front side. The location goes back by
alphabetical order.
 1-1-4H
ERRORS AND REMEDIAL MEASURES

Check Points & Remedial

Error Code Category Set Conditions Cause of problem
Measures
Pocket Gate
17 00 00 Solenoid 3
(PKG3)
Pocket Gate
18 00 00 Solenoid 4 Gate Position Abnormality - -
(PKG4)
Pocket Gate
19 00 00 Solenoid 5
(PKG5)
Motor Stop Error
1A 00 01 (Motor runs even after stop Same as code 11-00-07
command.)
Remove foreign matter from
Note Jam
transport path. Check drive belt.
Check connector for relay board
Wiring failure for Motor
(1MZ-007).
Driver or Motor (SHM3)
1A 00 02 Motor Initial Abnormality Replace relay board.
Motor Driver failure Replace Motor Driver.
Motor failure Replace Motor(SHM3)
Replace board 1MZ-002 or
Main CPU Board failure
1MZ-001.
Motor lower limit
1A 00 03 Same as code 12-00-02
Abnormality
Pocket Transport
Motor upper limit Same as code
1A 00 04 Motor 3
Abnormality 1A-00-02
(SHM3)
Motor Adjustment Error
Remove foreign matter from
1A 00 07 Adjusted data wasn’t in the Note Jam
transport path. Check drive belt.
range.
Motor Adjustment Error
1A 00 08 Same as code 1A-00-07
Motor speed was too slow.
Motor Adjustment Error
1A 00 09 Same as code 1A-00-07
Motor speed was too fast.
Pocket Gate
1F 00 00 Solenoid 7
(PKG7)
Pocket Gate
20 00 00 Solenoid 6
(PKG6)
S5G Gate Solenoid
21 00 00
(S5G)
FK RJ Change Gate Position
22 00 00 - -
(RJGSL) Abnormality
Pocket Gate
2A 00 00 Solenoid 8
(PKG8)
Pocket Gate
2B 00 00 Solenoid 9
(PKG9)
S6G Gate Solenoid
2C 00 00
(S6G)
23 00 02 Lowest Limit Error - -
23 00 03 Highest Limit Error - -
RJ Stacking Motor
(RJM) RJ Stack Pulse ITR Check detection plate.
23 00 04 Home Position Error sensor failure. Replace ITR sensor
Stacking Wheel noise Check mount of Stacking Wheel

*X in error code in this list will assign A to F on the display. It indicates sensor position when the plural
number of sensors are in the same line. “A” locates the most front side. The location goes back by
alphabetical order.
 1-1-5H
ERRORS AND REMEDIAL MEASURES

Check Points & Remedial

Error Code Category Set Conditions Cause of problem
Measures
RJ Stacking Motor
23 00 04 Home Position Error Motor failure Replace Motor or Drive Board
(RJM)
25 00 02 Lowest Limit Error - -
25 00 03 Highest Limit Error - -
Pocket 1 Stacking Pocket 1 Stack Pulse Check detection plate.
Motor ITPK1 sensor failure Replace ITPK1 sensor
25 00 04 (PKM1) Home Position Error
Stacking Wheel noise Check mount of Stacking Wheel
Motor failure Replace Motor or Drive Board
26 00 02 Lowest Limit Error - -
26 00 03 Highest Limit Error - -
Pocket 2 Stacking
Pocket 2 Stack Pulse Check detection plate.
Motor
ITPK2 sensor failure Replace ITPK2 sensor
26 00 04 (PKM2) Home Position Error
Stacking Wheel noise Check mount of Stacking Wheel
Motor failure Replace Motor or Drive Board
27 00 02 Lowest Limit Error - -
27 00 03 Highest Limit Error - -
Pocket 3 Stacking
Pocket 3 Stack Pulse Check detection plate.
Motor
ITPK3 sensor failure Replace ITPK3 sensor
27 00 04 (PKM3) Home Position Error
Stacking Wheel noise Check mount of Stacking Wheel
Motor failure Replace Motor or Drive Board
28 00 02 Lowest Limit Error - -
28 00 03 Highest Limit Error - -
Pocket 4 Stacking Pocket 4 Stack Pulse Check detection plate.
Motor ITPK4 sensor failure Replace ITPK4 sensor
28 00 04 (PKM4) Home Position Error
Stacking Wheel noise Check mount of Stacking Wheel
Motor failure Replace Motor or Drive Board
29 00 02 Lowest Limit Error - -
29 00 03 Highest Limit Error - -
Pocket 5 Stacking
Pocket 5 Stack Pulse Check detection plate.
Motor
ITPK5 sensor failure Replace ITPK5 sensor
29 00 04 (PKM5) Home Position Error
Stacking Wheel noise Check mount of Stacking Wheel
Motor failure Replace Motor or Drive Board
30 00 02 Lowest Limit Error - -
30 00 03 Highest Limit Error - -
Pocket 6 Stacking Pocket 6 Stack Pulse Check detection plate.
Motor ITPK6 sensor failure Replace ITPK6 sensor
30 00 04 (PKM6) Home Position Error
Stacking Wheel noise Check mount of Stacking Wheel
Motor failure Replace Motor or Drive Board
31 00 02 Lowest Limit Error - -
31 00 03 Highest Limit Error - -
Pocket 7 Stacking Pocket 7 Stack Pulse Fix detection plate.
Motor ITPK7 sensor failure Replace ITPK7 sensor
31 00 04 (PKM7) Home Position Error Stacking Wheel noise Check mount of Stacking Wheel
Motor failure Replace Motor or Drive Board
32 00 02 Lowest Limit Error - -
32 00 03 Highest Limit Error - -
Pocket 8 Stacking Pocket Stack Pulse Check detection plate.
Motor ITPK8 sensor failure Replace ITPK8 sensor
32 00 04 (PKM8) Home Position Error Stacking Wheel noise Check mount of Stacking Wheel
Motor failure Replace Motor or Drive Board
3B 00 02 Lowest Limit Error - -
3B 00 03 Pocket 9 Stacking Highest Limit Error - -
Motor Pocket Stack Pulse Check detection plate.
3B 00 04 (PKM9) Home Position Error ITPK9 sensor failure Replace ITPK9 sensor

*X in error code in this list will assign A to F on the display. It indicates sensor position when the plural
number of sensors are in the same line. “A” locates the most front side. The location goes back by
alphabetical order.
 1-1-6H
ERRORS AND REMEDIAL MEASURES

Check Points & Remedial

Error Code Category Set Conditions Cause of problem
Measures
Pocket 9 Stacking Stacking Wheel noise Check mount of Stacking Wheel
Motor
3B 00 04 Home Position Error
(PKM9) Motor failure Replace Motor or Drive Board

3C 00 02 Lowest Limit Error - -

3C 00 03 Highest Limit Error - -
Pocket 10 Stacking
Pocket Stack Pulse Check detection plate.
Motor
ITPK10 sensor failure Replace ITPK10 sensor
3C 00 04 (PKM10) Home Position Error
Stacking Wheel noise Check mount of Stacking Wheel
Motor failure Replace Motor or Drive Board
3D 00 02 Lowest Limit Error - -
3D 00 03 Highest Limit Error - -
Pocket 11
Pocket Stack Pulse Check detection plate.
Stacking Motor
ITPK11 sensor failure Replace ITPK11 sensor
3D 00 04 (PKM11) Home Position Error
Stacking Wheel noise Check mount of Stacking Wheel
Motor failure Replace Motor or Drive Board
3E 00 02 Lowest Limit Error - -
3E 00 03 Highest Limit Error - -
Pocket 12
Pocket Stack Pulse Check detection plate.
Stacking Motor
ITPK12 sensor failure Replace ITPK12 sensor
3E 00 04 (PKM12) Home Position Error
Stacking Wheel noise Check mount of Stacking Wheel
Motor failure Replace Motor or Drive Board
40 01 01
40 01 02
40 01 03 Position Sensor
Turn off and on the power.
40 01 04 Internal error. failure or dirt remains
Contact to Laurel.
40 01 07 at Position Sensor
40 01 08 Validator
40 01 09
40 01 20 P1L Sensor Error
40 01 21 Position Sensor failure
P1R Sensor Error Check Position Sensor and clean
or dirt remains at
40 01 22 P2L Sensor Error the Sensor.
Position Sensor
40 01 23 P2R Sensor Error
40 01 24
40 01 25
Clean Tape detection roller. Check
40 01 26 TD Sensor Error.
foreign object at TD Block Assy.
40 01 27
40 01 28
40 01 29 Upper UV Sensor Error Clean UV Sensor.
40 01 2a Bottom UV Sensor Error Contact to Laurel.
CCD failure or Jam at
40 01 2b CCD sensor Error Clean CCD Sensor.
Validator unit
40 01 2f Temperature Abnormality Turn off / on the power.
Validator
40 01 30 Internal error. Contact to Laurel.
40 01 31
Clean CCD Sensor.
40 01 33 CCD Sensor Error Sensor failure
Contact to Laurel.
40 01 34
40 01 35 Validator unit was opened. Close Validator unit.
40 01 80 Check connection of Interface
40 01 81 Interface Error cable (1MZ-001).
40 01 82 Contact to Laurel.
Load Country Setting.
40 01 83 Setting Error.
Contact to Laurel.
40 01 e0
40 01 e2 Validator
Sensor is not adjusted. Contact to Laurel.
40 01 e3
40 01 e4

*X in error code in this list will assign A to F on the display. It indicates sensor position when the plural
number of sensors are in the same line. “A” locates the most front side. The location goes back by
alphabetical order.
 1-1-7H
ERRORS AND REMEDIAL MEASURES

Check Points & Remedial

Error Code Category Set Conditions Cause of problem
Measures
40 01 e5 Sensor is not adjusted Contact to Laurel.
Check online manual Perform the
40 01 ee Miss operation.
Validator Operation correctly.
40 01 f1 Check connector of Validator.
Internal error
40 01 f2 Contact to Laurel.
41 00 31
41 00 32 Malfunction between Check cable and connector
Validator Validator Interface
41 00 33 1MZ-001 Board and connection. Replace Validator
(Internal) Abnormality
41 00 34 Validator. JDU-62 or 1MZ-001 Board.
41 00 35
Malfunction between Check cable and connector
Validator Validator Interface
41 00 40 Validator and Sub connection.
(Internal) Abnormality
Validator
41 01 --
41 02 01
41 02 02
41 02 03
41 02 04
41 02 05
41 02 06 Validator Interface -
Validator
41 02 07 Abnormality
41 02 12
41 03 41
41 03 42
41 03 43
41 03 50
41 03 51
42 00 00 USB I/F Error USB Data Error -
42 02 00 1PZ001-1MZ001 USB Interface Error
43 02 -- Main CPU Board Turn off on the power. Replace
Main CPU Board Internal Interface Error
44 02 -- 1MZ-001 failure 1MZ-001 Board.
Receiver Sensor is OFF Abnormal note. or Remove abnormal note. Resume
50 20 10 Sensor 201
when Emitter Sensor is ON. mechanical failure mechanical failure.
Sensor 301
50 30 1X The Sensor is dirty. Clean the sensor.
X=A (front) - F(back)
Sensor 302
50 30 2X X=A (front),
Sensor failure. Drive Check connection of the cable.
B(center), C(back)
Board 1MZ002 failure Replace sensor or 1MZ002.
Sensor 303
50 30 3X
X=A (front), B(Back)
Sensor 304
50 30 4X
X=A (front), B(Back)
Validator Sensor P1
50 31 1X
X=A (front), B (back)
Validator Sensor P2
50 31 2X
X=A (front), B (back)
50 35 10 Sensor 351 PKT-RJ
Sensor 401
50 40 1X
X=A (front), B (back)
50 40 20 Sensor 402
Sensor 403
50 40 3X Remaining Note. - -
X=A (front), B (back)
50 40 40 Sensor 404
Sensor 405
50 40 5X
X=A (front), B (back)
50 40 60 Sensor 406

*X in error code in this list will assign A to F on the display. It indicates sensor position when the plural
number of sensors are in the same line. “A” locates the most front side. The location goes back by
alphabetical order.
 1-1-8H
ERRORS AND REMEDIAL MEASURES

Check Points & Remedial

Error Code Category Set Conditions Cause of problem
Measures
Sensor 407
50 40 7X
X=A (front), B (back)
50 40 80 Sensor 408
50 40 90 Sensor 409 Remaining Note. - -
Sensor 409
50 40 9X
X=A (front), B (back)
50 45 10 Sensor 451 PKT-1
50 45 20 Sensor 452 PKT-2
50 45 30 Sensor 453 PKT-3
50 45 40 Sensor 454 PKT-4
Sensor 501
50 50 1X
X=A (front), B (back)
50 50 20 Sensor 502
Sensor 503
50 50 3X
X=A (front), B (back)
50 50 40 Sensor 504
Sensor 505
50 50 5X
X=A (front), B (back)
50 50 60 Sensor 506
Sensor 507
50 50 7X
X=A (front), B (back)
50 50 80 Sensor 508
Sensor 509
50 50 9X
X=A (front), B (back)
Sensor 551
50 55 11
(PKT-5)
Sensor 552
50 55 21
(PKT-6)
Sensor 553
50 55 31
(PKT-7)
Sensor 554
50 55 41
(PKT-8)
Sensor 601
50 60 1X
X=A (front), B (back)
50 60 20 Sensor 602
Sensor 603
50 60 3X Remaining Note. - -
X=A (front), B (back)
50 60 40 Sensor 604
Sensor 605
50 60 5X
X=A (front), B (back)
50 60 60 Sensor 606
Sensor 607
50 60 7X
X=A (front), B (back)
50 60 80 Sensor 608
Sensor 651
50 65 10
(PKT-9)
Sensor 651
50 65 11
(PKT-9)
Sensor 652
50 65 20
(PKT-10)
Sensor 652
50 65 21
(PKT-10)
Sensor 653
50 65 30
(PKT-11)
Sensor 653
50 65 31
(PKT-11)
Sensor 654
50 65 40
(PKT-12)

*X in error code in this list will assign A to F on the display. It indicates sensor position when the plural
number of sensors are in the same line. “A” locates the most front side. The location goes back by
alphabetical order.
 1-1-9H
ERRORS AND REMEDIAL MEASURES

Check Points & Remedial

Error Code Category Set Conditions Cause of problem
Measures
Sensor 654
50 65 41 - -
(PKT-12)
Sensor failure. Drive Check connection of the cable.
51 20 10 Sensor 201
Board 1MZ002 failure Replace sensor or 1MZ002.
Sensor 301 Sensor failure. Drive Check connection of the cable.
51 30 1X
X=A (front) - F(back) Board 1MZ002 failure Replace sensor or 1MZ002.
Sensor 302
51 30 2X X=A (front),
B(center), C(back)
Sensor 303
51 30 3X
X=A (front), B(Back)
Sensor 304
51 30 4X
X=A (front), B(Back)
Validator Sensor P1
51 31 1X
X=A (P1L), B (P1R)
Validator Sensor P2
51 31 2X
X=A (P2L), B (P2R)
51 35 40 Sensor 351
Sensor 401
51 40 1X
X=A (front), B(Back)
51 40 20 Sensor 402
Sensor 403
51 40 3X
X=A (front), B(Back)
51 40 40 Sensor 404
Sensor 405
51 40 5X
X=A (front), B(Back)
51 40 60 Sensor 406
Sensor 407
51 40 7X Remaining Note.
X=A (front), B(Back)
51 40 80 Sensor 408
51 40 90 Sensor 409
Sensor 409
51 40 9X
X=A (front), B (back)
Sensor 451
51 45 10
(PKT-1)
Sensor 452
51 45 20 - -
(PKT-2)
Sensor 453
51 45 30
(PKT-3)
Sensor 454
51 45 40
(PKT-4)
Sensor 501
51 50 1X
X=A (front), B(Back)
51 50 20 Sensor 502
Sensor 503
51 50 3X
X=A (front), B(Back)
51 50 40 Sensor 504
Sensor 505
51 50 5X
X=A (front), B(Back)
51 50 60 Sensor 506
Sensor 507
51 50 7X
X=A (front), B(Back)
51 50 80 Sensor 508
Sensor 509
51 50 9X
X=A (front), B (back)
Sensor 551
51 55 10
(PKT-5)

*X in error code in this list will assign A to F on the display. It indicates sensor position when the plural
number of sensors are in the same line. “A” locates the most front side. The location goes back by
alphabetical order.
 1-1-10H
ERRORS AND REMEDIAL MEASURES

Check Points & Remedial

Error Code Category Set Conditions Cause of problem
Measures
Sensor 551
51 55 11
(PKT-5)
Sensor 552
51 55 20
(PKT-6)
Sensor 552
51 55 21
(PKT-6)
Sensor 553
51 55 30
(PKT-7)
Sensor 553
51 55 31
(PKT-7)
Sensor 554
51 55 40
(PKT-8)
Sensor 554
51 55 41
(PKT-8)
Sensor 601
51 60 1X
X=A (front), B (back)
51 60 20 Sensor 602
Sensor 603
51 60 3X X=A (front)
B (back)
51 60 40 Sensor 604 Remaining Note. - -
Sensor 605
51 60 5X X=A (front), B
(back)
51 60 60 Sensor 606
Sensor 607
51 60 7X X=A (front),
B (back)
51 60 80 Sensor 608
Sensor 651
51 65 10
(PKT-9)
Sensor 651
51 65 11
(PKT-9)
Sensor 652
51 65 20
(PKT-10)
Sensor 652
51 65 21
(PKT-10)
Sensor 653
51 65 30
(PKT-11)
Sensor 653
51 65 31
(PKT-11)
Sensor 654
51 65 40
(PKT-12)
Sensor 654
51 65 41
(PKT-12)
60 20 10 Sensor 201 Abnormal note. Remove abnormal note.
Belt run off or other
60 30 10 Sensor 301 Resume mechanical failure.
mechanical failure.
60 30 20 Sensor 302 Same as code 50-30-1X Same as code 50-30-1X
60 30 30 Sensor 303
60 30 40 Sensor 304
60 31 10 Validator Sensor P1
60 31 20 Validator Sensor P2 Jam at Sensor - -
60 40 10 Sensor 401
60 40 20 Sensor 402
60 40 30 Sensor 403

*X in error code in this list will assign A to F on the display. It indicates sensor position when the plural
number of sensors are in the same line. “A” locates the most front side. The location goes back by
alphabetical order.
 1-1-11H
ERRORS AND REMEDIAL MEASURES

Check Points & Remedial

Error Code Category Set Conditions Cause of problem
Measures
60 40 40 Sensor 404
60 40 50 Sensor 405
60 40 60 Sensor 406
60 40 70 Sensor 407
60 40 80 Sensor 408
60 40 90 Sensor 409
60 50 10 Sensor 501
60 50 20 Sensor 502
60 50 21 Sensor 502
60 50 30 Sensor 503
60 50 40 Sensor 504
60 50 41 Sensor 504
60 50 50 Sensor 505
60 50 60 Sensor 502
60 50 61 Sensor 506
60 50 70 Sensor 507
60 50 80 Sensor 508 Jam at Sensor - -
60 50 81 Sensor 508
60 50 90 Sensor 509
60 60 10 Sensor 601
60 60 20 Sensor 602
60 60 21 Sensor 602
60 60 30 Sensor 603
60 60 40 Sensor 604
60 60 41 Sensor 604
60 60 50 Sensor 605
60 60 60 Sensor 606
60 60 61 Sensor 606
60 60 70 Sensor 607
60 60 80 Sensor 608
60 60 81 Sensor 608
61 30 12 Sensor 301-P2
61 30 23 Sensor 302-303
61 30 24 Sensor 303-304
61 30 31 Sensor 303-401
Sensor 303-409
61 30 39
or 303-501
61 31 12 Sensor P1-302
61 31 21 Sensor P2 - P1
61 40 12 Sensor 401-402
61 40 13 Sensor 401-403
61 40 34 Sensor 403-404
61 40 35 Sensor 403-405 Jam at between sensors Abnormal note. Remove abnormal note.
61 40 56 Sensor 405-406
61 40 57 Sensor 405-407
61 40 78 Sensor 407-408
61 40 91 Sensor 409-501
61 40 95 Sensor 409-509
61 50 12 Sensor 501-502
61 50 13 Sensor 501-503
61 50 34 Sensor 503-504

*X in error code in this list will assign A to F on the display. It indicates sensor position when the plural
number of sensors are in the same line. “A” locates the most front side. The location goes back by
alphabetical order.
 1-1-12H
ERRORS AND REMEDIAL MEASURES

Check Points & Remedial

Error Code Category Set Conditions Cause of problem
Measures
61 50 35 Sensor 503-505
61 50 56 Sensor 505-506
61 50 57 Sensor 505-507
61 50 78 Sensor 507-508
61 50 96 Sensor 509-601
61 60 12 Sensor 601-602
61 60 13 Sensor 601-603 Jam at between sensors Abnormal note. Remove abnormal note.
61 60 34 Sensor 603-604
61 60 35 Sensor 603-605
61 60 56 Sensor 605-606
61 60 57 Sensor 605-607
61 60 78 Sensor 607-608
62 30 12 Sensor 301-P2 Abnormal note Remove abnormal note.
62 30 23 Sensor 302-303
62 30 24 Sensor 302-304 Mechanical failre Resume mechanical failure.
Remove abnormal note.
Abnormal note
Check connection between S5G
62 30 31 Sensor 303-401 K8 Gate Solenoid S5G
and Drive Board1MZ002. Replace
failure
S5G.
Sensor 303-409 or
62 30 39
303-501
62 31 12 Sensor P1 - 302 Abnormal note Remove abnormal note.
62 31 21 Sensor P2 - P1 Mechanical failure
Resume mechanical failure.
Belt run off
62 40 12 Sensor 401-402 Remove abnormal note.
Abnormal note
Pocket 1 Gate Solenoid Adjust gate and check cable to
62 40 13 Sensor 401-403
PKG1 failure 1MZ002 board. Replace PKG1.
62 40 34 Sensor 403-404 Abnormal note Remove abnormal note.
Pocket 2 Gate Solenoid Adjust gate and check cable to
62 40 35 Sensor 403-405
PKG2 failure 1MZ002 board. Replace PKG2.
62 40 56 Sensor 405-406 Abnormal note Remove abnormal note.
Pocket 3 Gate Solenoid Adjust gate and check cable to
62 40 57 Sensor 405-407
PKG3 failure 1MZ002 board. Replace PKG3.
62 40 78 Sensor 407-408 Abnormal note. Remove abnormal note
Mechanical failure
62 40 91 Sensor 409-501 Resume mechanical failure.
Belt run off
Check connection between S6G
Under count between K8 Gate Solenoid S6G
62 40 95 Sensor 409-509 and Drive Board1MZ002. Replace
sensors failure
S6G.
Remove abnormal note. Resume
62 50 12 Sensor 501-502 Abnormal note
mechanical failure.
Pocket 4 Gate Solenoid Adjust gate and check cable to
62 50 13 Sensor 501-503
PKG4 failure 1MZ002 board. Replace PKG4.
Remove abnormal note. Resume
62 50 34 Sensor 503-504 Abnormal note
mechanical failure.
Pocket 5 Gate Solenoid Adjust gate and check cable to
62 50 35 Sensor 503-505
PKG5 failure 1MZ002 board. Replace PKG5.
Remove abnormal note. Resume
62 50 56 Sensor 505-506 Abnormal note
mechanical failure.
Pocket 6 Gate Solenoid Adjust gate and check cable to
62 50 57 Sensor 505-507
PKG6 failure 1MZ002 board. Replace PKG6.
Abnormal note
Remove abnormal note. Resume
62 50 78 Sensor 507-508 Mechanical failure
mechanical failure.
Belt run off
Remove abnormal note. Resume
62 50 96 Sensor 509-601 Abnormal note
mechanical failure.

*X in error code in this list will assign A to F on the display. It indicates sensor position when the plural
number of sensors are in the same line. “A” locates the most front side. The location goes back by
alphabetical order.
 1-1-13H
ERRORS AND REMEDIAL MEASURES

Check Points & Remedial

Error Code Category Set Conditions Cause of problem
Measures
Remove abnormal note. Resume
62 60 12 Sensor 601-602 Abnormal note
mechanical failure.
Pocket 7 Gate Solenoid Adjust gate and check cable to
62 60 13 Sensor 601-603
PKG7 failure 1MZ002 board. Replace PKG7.
Remove abnormal note. Resume
62 60 34 Sensor 603-604 Abnormal note
mechanical failure.
Under count between Pocket 8 Gate Solenoid Adjust gate and check cable to
62 60 35 Sensor 603-605
sensors PKG8 failure 1MZ002 board. Replace PKG8
Remove abnormal note. Resume
62 60 56 Sensor 605-606 Abnormal note mechanical failure.

Pocket 9 Gate Solenoid Adjust gate and check cable to

62 60 78 Sensor 607-608
PKG9 failure 1MZ002 board. Replace PKG9
63 30 12 Sensor 301-P2 Mechanical failure Resume mechanical failure.
63 30 23 Sensor 302-303 Sensor failure Replace sensor.
63 30 24 Sensor 302-304
63 30 31 Sensor 303-401
63 30 39 Sensor 303-409
63 31 12 Sensor P1 -302
63 31 21 Sensor P2 - P1
63 40 12 Sensor 401-402
63 40 13 Sensor 401-403 E

63 40 34 Sensor 403-404
63 40 35 Sensor 403-405
63 40 56 Sensor 405-406
63 40 57 Sensor 405-407
63 40 78 Sensor 407-408
63 40 91 Sensor 409-501
63 40 95 Sensor 409-509 Over count between sensors - -
63 50 12 Sensor 501-502
63 50 13 Sensor 401-403
63 50 34 Sensor 503-504
63 50 35 Sensor 503-505
63 50 56 Sensor 505-506
63 50 57 Sensor 505-507
63 50 78 Sensor 507-508
63 50 96 Sensor 509-601
63 60 12 Sensor 601-602
63 60 13 Sensor 601-603
63 60 34 Sensor 603-604
63 60 35 Sensor 603-605
63 60 56 Sensor 605-606
63 60 57 Sensor 605-607
63 60 78 Sensor 607-608

*X in error code in this list will assign A to F on the display. It indicates sensor position when the plural
number of sensors are in the same line. “A” locates the most front side. The location goes back by
alphabetical order.
 1-1-14H
ERRORS AND REMEDIAL MEASURES

Check Points & Remedial

Error Code Category Set Conditions Cause of problem
Measures
64 20 10 Sensor 201
64 30 10 Sensor 301
64 30 20 Sensor 302
64 30 30 Sensor 303
64 30 40 Sensor 304
64 31 10 Sensor P1
64 31 20 Sensor P2
64 40 10 Sensor 401
64 40 20 Sensor 402
64 40 30 Sensor 403
64 40 40 Sensor 404
64 40 50 Sensor 405
64 40 60 Sensor 406
64 40 70 Sensor 407
64 40 80 Sensor 408
64 40 90 Sensor 409
64 50 10 Sensor 501 Detecting Half Note Abnormal note Remove abnormal note
64 50 20 Sensor 502
64 50 30 Sensor 503
64 50 40 Sensor 504
64 50 50 Sensor 505
64 50 60 Sensor 506
64 50 70 Sensor 507
64 50 80 Sensor 508
64 50 90 Sensor 509
64 60 10 Sensor 601
64 60 20 Sensor 602
64 60 30 Sensor 603
64 60 40 Sensor 604

64 60 50 Sensor 605

64 60 60 Sensor 606
64 60 70 Sensor 607
64 60 80 Sensor 608
65 30 20 Sensor 302 Sensor Logic error Mechanical failure Resume mechanical failure.
65 31 12 Sensor P1 - 302 Sensor failure Replace Sensor.
Reject Gate Solenoid Adjust gate and check cable to
66 30 24 Sensor 302-304
RJGSL failure 1MZ002 board. Replace RJGSL.
66 30 30 Sensor 303 Same as Code 66-30-24 Same as Code 66-30-24
No Destination Error Gate Solenoid S5G Adjust gate and check cable to
66 40 10 Sensor 401
failure 1MZ002 board. Replace S5G.
Pocket 1 Gate Solenoid Adjust gate and check cable to
66 40 30 Sensor 403
PKG1 failure 1MZ002 board. Replace PKG1.
Pocket 2 Gate Solenoid Adjust gate and check cable to
66 40 50 Sensor 405
PKG2 failure 1MZ002 board. Replace PKG2.

*X in error code in this list will assign A to F on the display. It indicates sensor position when the plural
number of sensors are in the same line. “A” locates the most front side. The location goes back by
alphabetical order.
 1-1-15H
ERRORS AND REMEDIAL MEASURES

Check Points & Remedial

Error Code Category Set Conditions Cause of problem
Measures
Pocket 3 Gate Solenoid Adjust gate and check cable to
66 40 70 Sensor 407
PKG3 failure 1MZ002 board. Replace PKG3.
Gate Solenoid S6G Adjust gate and check cable to
66 40 90 Sensor 409
failure 1MZ002 board. Replace S6G.
Gate Solenoid S6G Adjust gate and check cable to
66 50 10 Sensor 501
failure 1MZ002 board. Replace S6G.
Pocket 4 Gate Solenoid Adjust gate and check cable to
66 50 30 Sensor 503
PKG4 failure 1MZ002 board. Replace PKG4.
Pocket 5 Gate Solenoid Adjust gate and check cable to
66 50 50 Sensor 505
PKG5 failure 1MZ002 board. Replace PKG5.
Pocket 6 Gate Solenoid Adjust gate and check cable to
66 50 70 Sensor 507 No Destination Error
PKG6 failure 1MZ002 board. Replace PKG6.
Gate Solenoid S6G Adjust gate and check cable to
66 50 90 Sensor 509
failure 1MZ002 board. Replace S6G.
Gate Solenoid S6G Adjust gate and check cable to
66 60 10 Sensor 601
failure 1MZ002 board. Replace S6G.
Pocket 7 Gate Solenoid Adjust gate and check cable to
66 60 30 Sensor 603
PKG7 failure 1MZ002 board. Replace PKG7.
Pocket 8 Gate Solenoid Adjust gate and check cable to
66 60 50 Sensor 605
PKG5 failure 1MZ002 board. Replace PKG8.
Pocket 6 Gate Solenoid Adjust gate and check cable to
66 60 70 Sensor 607
PKG9 failure 1MZ002 board. Replace PKG9.
Operating error
Feeding failure when NP Check cable to 1MZ002. Replace
Clutch CLT failure
67 01 00 (Note Press) down and ITB CLT.
is OFF. Feed Rollers wear Replace Feed Rollers
Mechanical failure Resume mechanical failure
Feed Unit Feeding failure, when NP
67 01 01 - Same as code 67-01-00
down and ITB is ON.
Feeding failure, when NP up
67 01 02 - Same as code 67-01-00
and ITB is OFF.
Feeding failure when NP up
67 01 03 - Same as code 67-01-00
and ITB is ON.
K4 Upper Door
Upper Door Switch Check cable to 1MZ002 board.
68 36 10 Switch USW1 set
USW1 failure Replace USW1.
switch
K8 Upper Door
Upper Door Switch Check cable to 1MZ002 board.
68 36 11 Switch USW2 set
USW2 failure Replace USW2.
switch
Validator JDU62 set
68 36 20 Validator set switch Set Failure Replace JDU62.
detection failure
Right Front Door Right Front Door Switch Check cable to 1MZ002.
68 46 10
MSW set switch. MSW failure Replace MSW.
Left Front Door SSW Left Front Door Switch Check cable to 1MZ002.
68 56 10
set switch. SSW failure Replace SSW.
Switching Regulator
68 80 40 24V error 1 +24V ZWS240PAF Replace the Switching Regulator.
failure
Low voltage
Switching Regulator
68 80 50 24V error 2 +24V ZWS150PAF Replace the Switching Regulator.
failure
Upper Door Switch
69 36 10 Upper Door switch Replace the switch.
USW1 failure
Upper Door Switch
69 36 11 Upper Door switch Replace the Switch.
USW2 failure
Set Failure
Validator JDU62 set
69 36 20 Validator set switch Replace JDU62.
detection failure
Right Front Door Right Front Door Switch
69 46 10 Replace the switch.
MSW set switch. MSW failure
*X in error code in this list will assign A to F on the display. It indicates sensor position when the plural
number of sensors are in the same line. “A” locates the most front side. The location goes back by
alphabetical order.
 1-1-16H
ERRORS AND REMEDIAL MEASURES

Check Points & Remedial

Error Code Category Set Conditions Cause of problem
Measures
Left Front Door SSW Left Front Door SSW
69 56 10 Set Failure Replace the switch.
set switch. failure
Switching Regulator
69 80 40 24V error 1 Insufficient voltage +24V ZWS240PAF Replace the Switching Regulator.
failure
Switching Regulator
69 80 50 24v error 2 Insufficient voltage +24V ZWS150PAF Replace the Switching Regulator.
failure
Upper Door Switch
6A 36 10
USW1 set switch
The door is opened.
Upper Door Switch
6A 36 11
USW2 Set Switch
Sensor was covered by Update Firmware to latest version
6A 36 20 Validator set switch
dust Replace SW
Front Door (R) set
6A 46 10 The Validator is opened.
switch
Front Door (L) set
6A 56 10
switch
6B 30 12 Sensor 301-P2

6B 30 23 Sensor 302-303

6B 30 24 Sensor 302-304
6B 30 31 Sensor 303-401
Sensor 303-409 or
6B 30 39
303-409
6B 31 12 Sensor P1-302
6B 31 21 Sensor P2-P1
6B 40 12 Sensor 401-402
6B 40 13 Sensor 401-403
6B 40 34 Sensor 403-404
6B 40 35 Sensor 403-305
6B 40 56 Sensor 405-406
6B 40 57 Sensor 405-407
6B 40 78 Sensor 407-408
6B 40 91 Sensor 409-501
6B 40 95 Sensor 409-509 Jam at between sensors Abnormal note. Remove abnormal note.
6B 50 12 Sensor 501-502
6B 50 13 Sensor 501-503

6B 50 34 Sensor 503-504

6B 50 35 Sensor 503-505

6B 50 56 Sensor 505-506

6B 50 57 Sensor 505-507
-
6B 50 78 Sensor 507-508

*X in error code in this list will assign A to F on the display. It indicates sensor position when the plural
number of sensors are in the same line. “A” locates the most front side. The location goes back by
alphabetical order.
 1-1-17H
ERRORS AND REMEDIAL MEASURES

Check Points & Remedial

Error Code Category Set Conditions Cause of problem
Measures
6B 50 96 Sensor 509-601
6B 60 12 Sensor 601-602
6B 60 13 Sensor 601-603
6B 60 34 Sensor 603-604 Jam at between sensors Abnormal note. Remove abnormal note.
6B 60 35 Sensor 603-605
6B 60 56 Sensor 605-606
6B 60 57 Sensor 605-607
6B 60 78 Sensor 607-608
70 20 10 Sensor 201
Sensor 251
70 25 1X
X=A (front), B (back)
Sensor 301
70 30 1X
X=A (front)-F(back)
Sensor 302
70 30 2X X=A (front),
B(center), C(back)
Sensor 303
70 30 3X
X=A (front), B(Back)
Sensor 304
70 30 4X
X=A (front), B(Back)
Sensor P1
70 31 1X
X=A (front), B (back)
Sensor P2
70 31 2X
X=A (front), B (back)
Sensor 351
70 35 1X X=A (front),
B(center), C(back)
Sensor 401
70 40 1X
X=A (front), B (back)
70 40 20 Sensor 402
Sensor 403 Check cable to 1MZ002. Replace
70 40 3X Sensor Adjustment Error. Sensor failer
X=A (front), B (back) the sensor.
70 40 40 Sensor 404
Sensor 405
70 40 5X
X=A (front), B (back)
70 40 60 Sensor 406
Sensor 407
70 40 7X
X=A (front), B (back)
70 40 80 Sensor 408
70 40 90 Sensor 409
70 45 10 Sensor 451 -
70 45 20 Sensor 452
70 45 30 Sensor 453
70 45 40 Sensor 454
Sensor 501
70 50 1X
X=A (front), B (back)
70 50 20 Sensor 502
Sensor 503
70 50 3X
X=A (front), B (back)
70 50 40 Sensor 504
Sensor 505
70 50 5X
X=A (front), B (back)

*X in error code in this list will assign A to F on the display. It indicates sensor position when the plural
number of sensors are in the same line. “A” locates the most front side. The location goes back by
alphabetical order.
 1-1-18H
ERRORS AND REMEDIAL MEASURES

Check Points & Remedial

Error Code Category Set Conditions Cause of problem
Measures
70 50 60 Sensor 506
Sensor 507 Check cable to 1MZ002. Replace
70 50 7X Sensor Adjustment Error. Sensor failer
X=A (front), B (back) the sensor.
70 50 80 Sensor 508
70 55 10 Sensor 551
70 55 20 Sensor 552

70 55 30 Sensor 553

70 55 40 Sensor 554
70 -- 91 All Sensors
71 20 10 Sensor 201 - -
Sensor 251
71 25 1X
X=A (front), B (back)
Sensor 301
71 30 1X
X=A (front)-F(back)
Sensor 302
71 30 2X X=A (front),
B(center), C(back)
Sensor 303
71 30 3X
X=A (front), B(Back)
Sensor 304
71 30 4X
X=A (front), B(Back)
P1L, R
71 31 1X
X=A (front), B (back)
Sensor P2L, R Error
71 31 2X
X=A (front), B (back)
Sensor 351
71 35 1X X=A (front),
B(center), C(back)
Sensor 401
71 40 1X
X=A (front), B (back)
71 40 20 Sensor 402
Sensor 403
71 40 3X Sensor Abnormality - -
X=A (front), B (back)
71 40 40 Sensor 404
Sensor 405
71 40 5X
X=A (front), B (back)
71 40 60 Sensor 406
Sensor 407
71 40 7X
X=A (front), B (back)
71 40 80 Sensor 408
Sensor 409
71 40 9X
X=A (front), B (back)
71 45 10 Sensor 451

71 45 20 Sensor 452

71 45 30 Sensor 453
71 45 40 Sensor 454
Sensor 501
71 50 1X
X=A (front), B (back)
71 50 20 Sensor 502
Sensor 503
71 50 3X
X=A (front), B (back)
71 50 40 Sensor 504

*X in error code in this list will assign A to F on the display. It indicates sensor position when the plural
number of sensors are in the same line. “A” locates the most front side. The location goes back by
alphabetical order.
 1-1-19H
ERRORS AND REMEDIAL MEASURES

Check Points & Remedial

Error Code Category Set Conditions Cause of problem
Measures
Sensor 505
71 50 5X
X=A (front), B (back)
71 50 60 Sensor 506
Sensor 507
71 50 7X
X=A (front), B (back)
71 50 80 Sensor 508
Sensor 509
71 50 9X
X=A (front), B (back)
71 55 10 Sensor 551
71 55 20 Sensor 552
71 55 30 Sensor 553
71 55 40 Sensor 554
Sensor 601
71 60 1X
X=A (front), B (back)
71 60 20 Sensor 602
Sensor 603
71 60 3X Sensor Abnormality - -
X=A (front), B (back)
71 60 40 Sensor 604
Sensor 605
71 60 5X
X=A (front), B (back)
71 60 60 Sensor 606
Sensor 607
71 60 7X
X=A (front), B (back)
71 60 80 Sensor 608
71 65 10 Sensor 651
71 65 20 Sensor 652
71 65 30 Sensor 653
71 65 40 Sensor 654
76 -- 90 Each Sensor
Error when updating Main CPU Board
E0 00 00 System Replace 1MZ001 board.
firmware. 1MZ001 failure
Battery, Operation or
Replace battery or 1MZ001 board
1MZ001 board error.
E1 80 60 System Battery level is low.
Main CPU Board
Replace 1MZ001 board.
1MZ001 failure
It does not generate It does not generate during
during operation. operation.
Data of sensor adjustment is Press Reset key to recover.
E1 80 61 Adjustment error
disappeared. Battery of main board Check all sensor levels and clean
was disconnected. the sensor which is dirty. Replace
motor driver one by one.
E2 70 10 CPU CPU Overflow - -
E3 20 10 Sensor 201
Sensor 251
E3 25 1X
X=A (front)-F(back)
Sensor 301
E3 30 1X
X=A (front)-F(back)
Sensor 302
E3 30 2X X=A(front), Pre-alarm The sensor is dirty. Clean the sensor.
B(center), C(back)
Sensor 303
E3 30 3X
X=A (front), B(Back)
Sensor 304 Error
E3 30 4X
X=A (front), B(Back)

*X in error code in this list will assign A to F on the display. It indicates sensor position when the plural
number of sensors are in the same line. “A” locates the most front side. The location goes back by
alphabetical order.
 1-1-20H
ERRORS AND REMEDIAL MEASURES

Check Points & Remedial

Error Code Category Set Conditions Cause of problem
Measures
Sensor P1
E3 31 1X
X=A (front)-B (back)
Sensor P2
E3 31 2X
X=A (front)-B (back)
Sensor 351
E3 35 1X X=A (front),
B(center), C(back)
Sensor 401
E3 40 1X
X=A (front)-B (back)
E3 40 20 Sensor 402
Sensor 403
E3 40 3X
X=A (front)-B (back)
E3 40 40 Sensor 404
Sensor 405
E3 40 5X
X=A (front)-B (back)
E3 40 60 Sensor 406
Sensor 407
E3 40 7X
X=A (front)-B (back)
E3 40 80 Sensor 408
Sensor 409
E3 40 9X Pre-alarm The sensor is dirty. Clean the sensor.
X=A (front)-B (back)
E3 45 10 Sensor 451
E3 45 20 Sensor 452
E3 45 30 Sensor 453
E3 45 40 Sensor 454
Sensor 501
E3 50 1X
X=A (front)-B (back)
E3 50 20 Sensor 502
Sensor 503）
E3 50 3X
X=A (front)-B (back)
E3 50 40 Sensor 504
Sensor 505
E3 50 5X
X=A (front)-B (back)
E3 50 60 Sensor 506
Sensor 507
E3 50 7X
X=A (front)-B (back)
E3 50 80 Sensor 508
E3 55 10 Sensor 551
E3 55 20 Sensor 552
E3 55 30 Sensor 553
E3 55 40 Sensor 554
E3 65 10 Sensor 651
E3 65 20 Sensor 652
E3 65 30 Sensor 653
E3 65 40 Sensor 654
E4 70 10 CPU
Abnormal system
E4 70 11 System - -
termination.
E4 70 12 Sensor 301-P2 - -
Display PCB Board
E5 72 40 Sensor 302-304 Irregular date set. Replace 1MZ101 board.
1MZ101 failure
E6 30 12 Sensor 301-P2
E6 30 24 Sensor 302-304 Note remains after clearing
E6 31 12 Sensor P1-302 note in transportation.

*X in error code in this list will assign A to F on the display. It indicates sensor position when the plural
number of sensors are in the same line. “A” locates the most front side. The location goes back by
alphabetical order.
 1-1-21H
ERRORS AND REMEDIAL MEASURES

Check Points & Remedial

Error Code Category Set Conditions Cause of problem
Measures
Note remains after clearing
E6 31 21 Sensor P2-P1
note in transportation.
E7 05 04 Cable damage between
System P4P8 communication error
E7 05 05 P4P8
Display PCB Board
F0 00 00 System Abnormality 1 Replace 1MZ101 board.
1MZ101 failure
F0 01 02 Display CPU Board Matching error of Contact LAUREL with Validator
F0 01 03 System Abnormality 2 Validator and security firmware version and Security
F0 01 04 Chip 1MZ012. Chip version.
Validator and
F0 01 31 Matching error
Security Chip
Cable damage
between
F0 01 41 Main PCB Board Power failure error
Display PCB and Main
PCB Board
F0 02 01 Power Voltage Abnormality
F0 02 02 Power Supply Power Cycle Abnormality Display PCB Board Replace 1MZ101 board.
1MZ101 failure
F0 02 03 Power Cycle Abnormality
Main CPU Board
F0 02 10 Main CPU Board CPU Abnormality Replace 1MZ001 Board.
1MZ001 failure
F0 02 11
F0 02 12 CPU Abnormality As above As above
F0 02 13
F0 02 14 CPU Board
F0 02 20 As above As above
F0 02 21 CPU I/F Abnormality Main CPU Board Replace 1MZ001 Board.
F0 02 22 1MZ001 failure
F0 02 23
F0 02 24 CPU I/F Abnormality Main CPU Board Replace 1MZ001 Board.
F0 02 25 1MZ001 failure
F0 02 26
F0 02 30 CPU Board
F0 02 31 CPU Board Abnormality As above As above
F0 02 32
It does not generate during
It does not generate
F0 02 33 operation.
during operation.
F0 02 40 Security Chip damage Replace Security Chip.
It does not generate during
Security chip Security Chip Abnormality It does not generate
F0 02 41 operation.
during operation.
F0 02 F0 Firmware System Abnormality
F0 02 F1 CPU Board System Abnormality
F0 02 F2 System CPU Abnormality
F0 02 FC Others Emergency Stop Operation
F0 02 FE System Wrong Software Version AC power failure Change the outlet
F0 02 FF Not used Not used
F0 03 10 Validator Fan Abnormality
F0 80 20 Power Supply Power source of 5V is low
F0 80 30 Power Supply Power source of 12V is low

*X in error code in this list will assign A to F on the display. It indicates sensor position when the plural
number of sensors are in the same line. “A” locates the most front side. The location goes back by
alphabetical order.
 1-1-22H
ERRORS AND REMEDIAL MEASURES

Check Points & Remedial

Error Code Category Set Conditions Cause of problem
Measures
MSW2-4 is set ON
F0 C0 01 Main Firmware Matching error with incorrect Set MSW2-4 to OFF.
Firmware Version
Firmware version is Contact LAUREL with Validator
F0 C0 -- Display Firmware Matching error
incorrect firmware version
Cable Connection
Check cables and connector
failure
Validator JDU62
Replace Validator
failure
No Security Chip
Mount Security Chip
1MZ012
F1 01 - Display Firmware Interface abnormality Security Chip damage Replace Security Chip
Main CPU Board
Replace 1MZ001 Board
1MZ001 failure
Display Board
Display Board.
1MZ101 failure
Cable connection
Check cable and connectors.
failure
F1 03 50 Validator I/F Abnormality
F1 05 01
Between P4 Units and P8 Cable damage
F1 05 02 System
Unit communication error between P4-P8
F1 05 03

● System Error
In case Interface problem for Display PCB Board, Sub-Display may indicates additional error code.

Sub-Display Cause of Check Point & Remedial

Category Set Conditions
Error Code problem Measures
P System Power Problem - -
E System Main CPU Board Problem - -
Communication Error
J System - -
Validator-CPU board.
S System Security Chip Error - -

*X in error code in this list will assign A to F on the display. It indicates sensor position when the plural
number of sensors are in the same line. “A” locates the most front side. The location goes back by
alphabetical order.
 1-1-23H
ERRORS AND REMEDIAL MEASURES

● Reject / Fitness Info

Reject Info
Item Description Item Description
UV Ultraviolet fluorescence detection Width Longer Edge Size detection
MG Magnetic property detection Length Shorter Edge Size detection
OP *1) Thickness Thickness detection
Skew Skew feeding at Validator Tape Tape detection
Skew M Skew feeding at 301 sensors IR Image Infra red image detection
Near Feed Notes distance is too close. Clear To clear notes when transport error.
Over Run Validator failed discrimination Other No destination

*1） It is reserved for future function for each country.

LAUREL will inform distributor directly when the function is applied to it.

Fitness Info
Item Description Item Description
Dirt Soil detection Dimension Size detection
Hole, Tear Hole or Tear detection Other1 *1）
Fold Fold detection
Other2 *2)

*1), *2) It is reserved for future function for each country.

LAUREL will inform distributor directly when the function is applied to it.

*X in error code in this list will assign A to F on the display. It indicates sensor position when the plural
number of sensors are in the same line. “A” locates the most front side. The location goes back by
alphabetical order.