Flash Charging

the Future

Flash Charging

TECHNICA L PA PER

© OPPO 2021 • All rights reserved

 



CONTENTS

OPPO 
Flash Charging Technical Paper
Preface 1

1  VOOC Flash Charging Technology Overview 2

 2
4

 5

2.1 Overview of VOOC Standards 5

2.2 E Fast Charge Protocol 5
2.3 VOOC Performance & Five-Star Safety Assessment Scheme  11

 16

3.1 VOOC Ecology Prospects 16

3.2 VOOC Ecosystem Accessories Certificate 17

4  The Future of VOOC 22

4.1 Development Trend of VOOC Technology 22

4.2 Summary 23
 1


PREFACE 

OPPO 
Our use of smartphones and other connected devices is constantly
increasing. The number of smartphone users worldwide has reached
nearly 4 billion – around half the global population1 at the start of 2021.

Flash Charging Technical Paper

As smartphone functions improve, they consume more electricity.
This increased power demand comes from higher display resolutions,
advanced processors, camera systems and more. But as users expect
more from their devices, these raised expectations include better
battery life – and higher battery capacities mean longer charging times.
Fast charging technology was developed against this backdrop of slow
smartphone recharge times.

Fast charging technology can improve charging efficiency, reducing the

time to charge devices. Several fast charging solutions have already
appeared, mainly falling into two categories: high-voltage, low-current
and low-voltage, high current.

While both normal and fast charging are in use, companies have
focused on device compatibility with each technology. Many have
created new terminals and adaptors, while some have worked
towards mutual compatibility, even across a variety of brands. But
for the long-term development of fast charging technology, more
standardization efforts are needed across several industries.

1 www.statista.com/statistics/330695/number-of-smartphone-users-worldwide
 2


1 VOOC FLASH CHARGING 
TECHNOLOGY OVERVIEW

OPPO 
Flash Charging Technical Paper
OPPO first offered a low voltage, fast charge solution in 2014, releasing
the independently developed VOOC 22.5W (5V / 4.5A) flash charger. This
device delivered higher charging power, charging devices four times
faster than normal charging technology, and 50% faster than other fast
charging technologies.

In 2018, OPPO made further improvements to VOOC flash charging

technology, releasing SuperVOOC. SuperVOOC has twice the charging
power of VOOC, so the 50W SuperVO0C adapter could charge a
3,400mAh capacity battery to full in 35 minutes. In 2019, the 65W
SuperVOOC 2.0 charger could charge a 4,000mAh battery to full in
30 minutes, breaking the previous record.

1.1 Definition of VOOC Flash

Charging Technology
According to the definitions of the China Fast Charging Standard
Technical Requirements and Test Methods for Fast Charging of Mobile
Communication Terminals:

Fast charging is an electrical system which consists of an adaptor,

cable and terminal. Charging takes 30 minutes from beginning to end,
with an average input current greater or equal to 3A, and the total
charge capacity should always be greater than or equal to 60% of the
battery’s rated capacity.

VOOC (Voltage Open Loop Multi-step Constant-Current Charging) is

one of the systems that enables flash charging technology. It relies
on dynamic interaction between the adapter and the terminal, as
they communicate and work together to track voltage load. This
communication underpins direct charging, as it allows the system
to control the flow of power and maintain a constant voltage level.
The open voltage loop allows for segmented current throughput in
high current mode, while the slender design improves the terminal’s
charging power.
 3

The defining characteristic of VOOC flash charging technology is that

it improves the speed and efficiency of fast charging by increasing the 
current output, rather than the voltage. It also avoids the overheating
issue that high-voltage fast charging solutions encounter, thanks to
constant voltage increases, an enhanced structure, moving the charging 
control circuit to the charger, and using charge pump partial pressure
technology – all of which also means that it does not need to conduct a
secondary voltage conversion. 
A diagram of the VOOC flash charging system framework and functional
principles is shown below:

OPPO 
TERMINAL

Batteries Charging

Flash Charging Technical Paper

and Circuit Charging
Protection Management Port
Circuit Module

FAST CHARGING CABLE

Encryption
Cable
Circuit

CHARGER

Charging
Charging Circuit
Port Management
Module

Figure 1.1  VOOC Flash Charging System Framework

ADAPTOR TERMINAL

VBUS VBUS Fast Charging

Power
Switch
GND GND

CABLE Battery

D+ D+
Fast Charging
Control Unit
Control Unit
D– D–

Figure 1.2  VOOC Flash Charging Functional Principle

 4

1.2  Features of VOOC Technology


1  Direct Charging Structure
With direct charging, there is no depressurisation inside the phone. 
This reduces the amount of heat produced by voltage conversion and
improves charging efficiency.

The latest version of VOOC technology – SuperVOOC 2.0 – has added a
high precision adjustment function to control current and voltage even

OPPO 
more accurately and efficiently, and reduce system losses. It adjusts
voltage on a scale between 3V and 10V, and current between 0A and
6.5A, achieving a minimum of 100mA.

Flash Charging Technical Paper

2  Two-way Communication
When the phone activates fast charging, the phone and the adapter
will monitor and synchronize the status of the phone battery, adapter,
interface, and mobile application scenarios in real time. Through this
two-way communication between phone and adapter, the adapter
can deliver smarter charging, by automatically reducing or increasing
charging power as needed.

3  Smart Safety Protection

A safety scheme is in place from the adapter all the way through to
the battery. Dedicated charging control units in both the device and
the adapter monitor the status of components in real time, checking
battery temperature, voltage, current, path impedance and numerous
other parameters. The system can then respond quickly if any parameter
strays outside the norm, to avoid abnormal charging.

In addition, fast charging only begins when an adapter is connected

with the correct encrypted identity authentication. New hardware
detection circuits on both the battery and the adapter sides also
protect against over-discharge and excessive voltage, current or battery
temperature during charging. These variables are also monitored inside
the adapter in real time, by a combination of software and hardware,
to ensure safe charging in every aspect of the system.

Speed Safety Coolness

Average terminal
More than 100 million
4 times as fast as temperature: 32°C
units dispatched,
traditional charger
no safety liability issues Temperature
fluctuation: 3.3°C

Charge for 5 minutes, Five-level smart safety Bright screen charging,

talk for 2 hours protection charge and play at the
same time

Figure 1.3  Characteristics of VOOC Flash Charging Technology:

Speed, Safety, Coolness
 5


2 VOOC STANDARDS 
& PERFORMANCE

OPPO 
ASSESSMENT SCHEME

Flash Charging Technical Paper

2.1  Overview of VOOC Standards
In June 2014, the China Telecommunication Technology Labs of the
China Academy of Information and Communication Technology,
together with OPPO, Huawei, Qualcomm, and MediaTek jointly
formulated YDB 195–2018: Technical requirements and test methods for
fast charging of mobile communication terminals. Five fast charging
protocols were standardised, with OPPO’s VOOC flash charging protocol
named the E Fast Charge Protocol. Released on 20 March 2018,
YDB 195–2018 was the first international standard for fast charging
technology, and it is now being upgraded to an industry standard.

The aim of this standard is to promote the use of flash charging

technology in compatible mobile terminals, steer product R&D, and
guide equipment manufacturers. The hope is that this will create a fast,
safe and compatible charging environment for mobile phone users,
and regulate the development of a flash charging industry.

2.2  E Fast Charge Protocol

The E protocol enables the two-way communication between the
fast charging adaptor and mobile communication terminals (referred
to below as a “terminal”), which supports VOOC flash charging.
Transmission is carried out using serial communication technology, via a
D+ D– signal USB data cable.

The E charging system framework diagram is shown in Figure 2.1.

The terminal is connected to an adaptor via a USB cable. D+ is used

during transmission by a CLK clock signal, and D– is used during
transmission by a DATA data transmission signal.
 6

TERMINAL

Batteries Charging

and Circuit Charging
Protection Management Port
Circuit Module

FAST CHARGING CABLE

Encryption

Cable
Circuit

OPPO 
CHARGER

Charging
Charging Circuit
Port Management

Flash Charging Technical Paper

Module

Figure 2.1  The E Charging System Framework

Before switching on fast charging, the terminal and the adaptor

must have a complete communication circuit established, to begin
the transmission of information. The terminal and the adaptor must
have the fast charging function switched on, otherwise only normal
charging will occur.

The fast charging adaptor serves as the host, providing a CLK clock
signal in the communication process. The signal between the terminal
and the adaptor always comes from the adaptor.

2.2.1  Fast Charge Protocol Process

2.2.1.1  The Fast Charge Initiation Process

Recharging
Current (A)
15 1 2 3 4 5

14 Flash Charge
Open Stream
13

12

11

0 Time (s)
T1 T2 T3 T4

Figure 2.2  The Fast Charge Open Stream

 7

As Figure 2.2 shows, the fast charge starting process contains

five stages: 

Stage 1

» After the terminal and the fast charging adaptor complete
handshake, the terminal will initiate fast charging.

Stage 2

OPPO 
» The adaptor assesses and adjusts the output voltage to a suitable
value for the terminal.

Stage 3

Flash Charging Technical Paper

» The adaptor receives the maximum charging current supported by
the terminal for that state.

Stage 4 & 5

» The adaptor sets its output current at the specified value, and the
constant current stage begins.

» When this stage begins, the adaptor initiates a security check and
switches on the protection mechanism. During this period, the
terminal and the fast charging adaptor are in constant battery
contact, ensuring the stability of the charging process.

2.2.1.2  The Fast Charge Communication Process

The fast charge communication process is shown in Figure 2.3.

FAST CHARGE COMMUNICATION FLOW CHART

Start

DCP default mode

Adaptor and terminal complete handshake, terminal agrees to flash charge

Adaptor adjusts output current to compatible value

Adaptor obtains maximum charge current for present status

Based on size of flash current, initiates constant current mode

Adaptor initiates protection mechanism and exchanges

battery, and other device information with terminal

Figure 2.3  Fast Charge Communication Flow Chart

 8

2.2.2 Implementation of the Fast Charge Physical Layer


2.2.2.1 Fast Charge Functions Flow Chart and Principles

The fast charge functions flow chart is shown in Figure 2.4. 

ADAPTOR TERMINAL

VBUS VBUS Fast Charging
Power
Switch
GND GND

OPPO 
CABLE Battery

D+ D+
Fast Charging
Control Unit
Control Unit
D– D–

Flash Charging Technical Paper

Figure 2.4  Fast Charging Function Principles Block Diagram

The entire fast charging circuit core is comprised of two control units,
allocated to the adaptor and terminal. At the fast charging initiation
stage, a handshake occurs through a reading of D+ and D– signals from
these two units, which control several functions, including adjustment of
the power unit’s output, the fast charging on/off switch, monitoring the
charging process, and handling unexpected errors.

D+ uses a CLK data transmission handshake signal, D– uses a DATA

data transmission handshake signal.

2.2.2.2  USB Data Line Structure

The data line at one end should be a USB A-type connector, and its
mechanical structure must comply with the requirements of USB 2.0
specifications. The other end of the data line can be a 7Pin Micro-USB
B-type connector: its mechanical structure is shown in Figure 2.5.

The data line can also be a USB C-type connector and its
mechanical structure design should meet the requirements of
the USB 3.1 specification.

Figure 2.5  7Pin Micro-USB B-type Connector

Interface Structure and Dimensions
 9

2.2.2.3  Pin Definitions

USB A-type connector pin definitions must comply with the


specifications in Table 2.1.

Pin number Pin definition 

1 VBUS

2 D–

3 D+

4 GND

OPPO 
5 ID

Table 2.1  Definitions of Cable A End Connector Pins

Flash Charging Technical Paper

7Pin Micro-USB B-type connector pin definitions must comply with the
specifications in Table 2.2.

Pin number Pin definition

1 VBUS

2 VBUS

3 D–

4 D+

5 ID

6 GND

7 GND

Table 2.2  Definitions of 7Pin Micro-USB B-type Connector Pins

2.2.2.4  Electrical Specifications for Adaptor End Signal Wire

Type of Signal Min. Value Std. Value Max. Value Conditions Unit

High input level* VDD -0.7 - - 3.2< VDD<4.5 V

Low input level* - - 0.8 3.2< VDD<4.5 V

High output level* 0.25VDD+0.8 - 4.5 3.2< VDD<4.5 V

Low output level* - - 0.15 VDD 3.2< VDD<4.5 V

*Input and output data in Table 2.3 is represented by CLK and DATA adaptor pins.

Table 2.3  Electrical Specifications for Adaptor End Signal Wire

 10

2.2.3 Safety Guarantee Mechanism


2.2.3.1 Adaptor End Safety Measures

During the fast charging process, the adaptor end safety measures are
as follows:

1. Charging path impedance is monitored in real time, and the fast
charging function is shut down if any abnormality is detected.

2. If communication is lost between the adaptor and terminal, the fast

OPPO 
charging function is shut down.

3. In accordance with differences between terminal specifications and

the charging current, the guaranteed current cannot exceed the

Flash Charging Technical Paper

terminal design specifications.

4. The adaptor monitors the voltage of the battery in real time and
adjusts the current to ensure battery safety.

2.2.3.2 Terminal End Safety Measures

During the fast charging process, the terminal end safety measures
are as follows:

1. Real-time monitoring of battery status: if a failure to comply with

battery status requirements is detected, the fast charging function
is shut down.

2. Real-time monitoring of each high-current interface: if the interface

temperature exceeds the standard, the fast charging function is
shut down.

3. Real-time monitoring of charging current: if the charging current

exceeds the design specifications, the fast charging function is
shut down.

4. If communication is lost between the adaptor and terminal, the

fast charging function is shut down.
 11

2.3 VOOC Performance & Five-Star

Safety Assessment Scheme


2.3.1 SuperVOOC Five-Star Assessment and 

Testing Scheme
In 2018, China Telecommunication Technology Labs (CTTL) released 
a five-star rating scheme to assess fast charging performance – a
full assessment of the quality, speed and safety of fast charging

OPPO 
applications. It drew on CTTL’s in-depth experience with fast-charging
technologies and was based on existing standards, whilst also
recognising increased performance requirements.

Flash Charging Technical Paper

The scheme assesses four dimensions of mobile and charging systems:
charging speed, system safety, charging temperature, and efficiency.

Each assessment metric is scored out of five, based on the CTTL Fast
Charging Performance Rating Scheme, with the total score deciding the
final grade. The product is then given an overall star rating between one
and five.

No. & assessment item Assessment content

1 Charging speed Time to charge the battery to 100% from

automatic shut-down

2 Safety Evaluates the safety of the entire charging system,

including charger, cable, battery and end device

3 Charging temperature Assesses maximum temperature and charging speed of

the end device under different conditions

4 Energy efficiency Energy conversion efficiency of the charger and

charging system

Table 2.4  Fast Charging Performance Five-Star Rating Scheme

Figure 2.6  Fast Charging Capability Certificate

 12

2.3.2 SuperVOOC 2.0 Testing Scheme

Building on its Fast Charging Performance Rating Scheme, CTTL has 
added a battery life cycle test, so the testing scheme now looks at five
areas. This update was based on certification standards for consumer
electronics and informed by current developments and applications of 
fast charge technologies.

This document covers the assessment of the Reno4 Pro, equipped with 
SuperVOOC 2.0.

OPPO 
No. & Dimension Test
1 Charging Video call mode: Simulation of an online video call
temperature
(temperature Gaming mode: Simulation of a consumer playing an online game
under different

Flash Charging Technical Paper

Video mode: Simulation of a user watching videos online
fast charging
conditions Recording mode: Simulation of a user recording high definition
and different videos
product
Car mode: Simulation of a user using GPS when driving
operating
conditions) Heaviest load mode: Simulation of CPU and GPU at full load

2 Charging Basic test: Fast charging recognition, overvoltage and high / low

safety temperature protection

Single fault: Fault testing of the aforementioned 5-step protection

3 Charging Charging speed: Verification of the charging speed in different

performance use environments and after data cable degradation, using
battery charge measurements

Trickle current duration: Verification of trickle current duration by

monitoring voltage, current and battery charge during charging

4 Charging Adapter input – battery input energy conversion efficiency

performance
Adapter output – battery input energy conversion efficiency

5 Battery life Battery life: After carrying out battery charge and discharge
cycling at the nominal charging rate of the battery, the life of the
battery is verified by measuring the battery capacity.

Battery cell life: After carrying out battery charge and discharge
cycling at the nominal charging rate of the battery, the life of the
battery is verified by measuring the battery capacity.

Table 2.5  SuperVOOC 2.0 Testing Scheme

The significant increase in the charging power of SuperVOOC 2.0 –

added to the wide range of end devices and scenarios where multiple
functions are used – makes temperature control a huge challenge during
charing. Temperature control capability is one of the characteristics of
VOOC charging technology.

The SuperVOOC 2.0 Testing Scheme includes multiple complex testing

scenarios that simulate the real situations where consumers use
fast charging technologies. This allows the charging temperature of
SuperVOOC 2.0 to be assessed under various load environments. The
results show that while power is increased, the charging temperature of
the product – Reno4 Pro – is far lower than the temperature defined in
international electrical safety standard IEC 62368–1, or Chinese national
standard GB 4943.1–2011. This reflects the strength of OPPO’s fast
charging technology.
 13

Change in Charging Speed

Charging
at Room Temperature (25°C) Charging 
Capacity (mAh) Current (A)




OPPO 
Figure 2.7  Reno4 Pro Change in Charging Speed

Flash Charging Technical Paper

at Room Temperature (25°C)

Change in Charging speed

Charging Charging
at Low Temperature (10°C) Current (A)
Capacity (mAh)

Figure 2.8  Reno4 Pro Change in Charging Speed

at Low Temperature (10°C)

The charging performance test mainly covers charging speed and trickle
current duration. The charging speed is the time it takes to charge the
battery to 100% from automatic shut-down: this is the most tangible
part of the consumer experience.

The demand for fast charging research and development comes from
the excessively long charging time of most charging methods. As end
device functions increase, so does power consumption – but battery
capacity is not growing at the same rate. Fast charging technologies
can therefore save consumers a significant amount of time.

This testing scheme verifies charging speed by monitoring charging

current, charging capacity and several other technical metrics during
charging. In the case of the Reno4 Pro, the device can be fully charged
in 35 minutes in a variety of temperatures, including 10°C and 25°C.
 14

For devices that use non-removable batteries, the battery life may
represent the usable life of the end device itself. And in fast charging 
systems, high speed charge and discharge cycles inevitably impact
battery life. Following the Chinese national standard GB/T 18287-2013:
General Specification for Lithium Ion Batteries and Battery Packs for 
Mobile Phones, CTTL verifies the battery’s long life cycle by simulating
repeated fast charge and discharge cycles. By comparing the battery’s
capacity before and after, we see that even if the battery and battery 
cell go through this process hundreds of times, capacity remains at
97.4% and 94.6% of rated capacity, respectively. Thus we can see that

OPPO 
the battery life of the Reno4 Pro has not been affected.

Battery Cell 400-cycle

Charging
Charging Capacity Change

Flash Charging Technical Paper

Capacity (mAh)

Discharge Cycle

Figure 2.9  Change in the Battery Cell Charge and

Discharge Cycle Capacity of the Reno4 Pro

Battery 300-cycle
Charging Charging Capacity Change
Capacity (mAh)

Discharge Cycle

Figure 2.10  Change in the Battery Cell Charge and

Discharge Cycle Capacity of the Reno4 Pro
 15

Rated Capacity Percentage of Rated

Capacity after Cycle Capacity Retained 
Cell (400 cycles) 1,955 mAh 1,851 mAh 94.6%

Battery (300 cycles) 1,955 mAh 1,906 mAh 97.4%


Table 2.6  Capacity Change of Battery Cell and Battery
through Charge and Discharge Cycles

Fast charging speeds must not come at the expense of safety, so

OPPO 
fast charging technologies must take safety into consideration as
much as speed. Based on its accumulated know-how in fast charging
technologies – and its safety testing experience – CTTL has established
a complete assessment and testing system covering the charger, data

Flash Charging Technical Paper

cable, mobile device and mobile battery.

Charging efficiency consists of two parts: the efficiency of the entire

charging system (from adapter input to battery input) and the efficiency
of the end device (from end device input to the energy that enters the
battery). Fast charging technologies must not only meet the demand
for faster charging, but also comply with national environmental
and energy-saving policy objectives, by making each drop of
energy genuinely available to the user.

POWER Power Power

Adapter Phone Battery
SUPPLY Meter Meter
1 2

Figure 2.11  Energy Conversion from Adapter Input to Battery Input

POWER Power Power

Adapter Phone Battery
SUPPLY Meter Meter
1 2

Figure 2.12  Energy Conversion from Adapter Output to Battery Input

The results of the tests described above show that this mobile device
can fully charge within 35 minutes, while also ensuring that the heat
emitted by the adapter and end device is lower than the values
required by international and Chinese national standards. In addition,
the five-step safety protections of SuperVOOC 2.0 ensure the safety
of the consumer using the fast charging technology.

After carrying out battery charge and discharge cycling at the nominal
charging current of the battery, the battery’s capacity remained at
more than 94% of its rated capacity.

Each test metric reflects the advanced status of SuperVOOC 2.0

technology and demonstrates the strong overall capabilities of OPPO.
 16


3 VOOC APPLICATIONS & 
ECOSYSTEM CERTIFICATION

OPPO 
Flash Charging Technical Paper
3.1  VOOC Ecology Prospects
As OPPO’s proprietary technology, VOOC Flash Charge technology was
the first rapid charging technology to receive a five-star rating from CTTL,
proving its effectiveness, safety and reliability. In addition, by the end of
2020, OPPO had applied for more than 2,950 patents relating to VOOC
Flash Charge technology, and nearly 1,400 of these had been granted.
This wide-reaching patent coverage provides the comprehensive legal
protection needed for the continued global development of these products.

OPPO has also worked with CTTL to establish the VOOC Flash Charge
industry standard. This standard will ensure the compatibility of rapid
charging technology in smart devices across the industry. It will also guide
the development and creation of devices by multiple manufacturers,
ensuring fast and safe charging for mobile phone users, and a healthy,
standardised rapid charging industry.

By continuing to concentrate on users’ core needs, OPPO is bringing VOOC

Flash Charge innovations to this wider field of applications and user
devices, through these partners. Some of the possible applications include
in-car charging, office charging and charging in public spaces. The hope is
that one charger could be used for a variety of devices, from smartphones
to tablet computers, laptops or wearables. And the overall aim is to provide
users with the benefits of rapid charging at any time and any place,
addressing the power needs of consumers in the mobile 5G era.
 17

Guided by FRAND principles, OPPO has openly licensed its flash charging
technology to over 40 outstanding partners so far. These include chip 
businesses like Rockchip, Injoinic Technology, Ismartware, Southchip,
Silan, Anker Innovations, Bull, Romoss, Mophie and Aukey, as well as
charging services providers, such as Dian Baobao. OPPO is also active 
in the field of vehicle electronics and in-car charging, partnering with
NXP Semiconductors and vehicle module producers like ADAYO and
Desay SV, as well as car makers FAW-Volkswagen. By using VOOC Flash 
Charge technology, these 40-plus partners will bring rapid charging to
a broad range of settings.

OPPO 
To ensure products with licensed VOOC technology are both cutting
edge and safe, OPPO provides partners with technical guidance and
support during the patent licensing process. In addition, the company

Flash Charging Technical Paper

uses closed loop licensing monitoring to ensure product quality is
verified before go-to-market – as well as dynamic quality tracing and
management after release.

OPPO partners’ VOOC products undergo enhanced safety testing and

certification, thanks to ongoing work with China Telecommunication
Technology Labs (CTTL) of the China Academy of Information
and Communications Technology. These rigorous checks ensure
standardised safety and quality certification to the strictest standards.

3.2  VOOC Ecosystem

Accessories Certificate
TL Certification Centre (TLC) is a certification body, owned and operated
by the China Academy of Information and Communication Technology.
TLC provides certification for products, services, and management
bodies in the information and communications sector. It also delivers
evaluation services for information management systems and green
factory operations.

Between its 15 contract laboratories, TLC has certified over 300 different
products, which are now in use across broadcast, rail transport, banking,
government ministries and more. The company also provides electronic
authentication services, as well as digital certification security solutions
for clients in communications, transport, finance, IoT and other sectors.

In 2018, TLC became the certifying body for OPPO’s VOOC ecosystem
products, ensuring that any accessory product equipped with VOOC
flash charging is safe and effective.
 18

3.2.1  Product Classification & Technical Standard Systems

VOOC accessory products are organised into the following categories, 
according to licence agreements and product attributes:

» Flash charge protocol chips 

» AC adaptors (chargers)

» Car DC chargers

» Mobile power sources

» Flash charging cables

OPPO 
» Other devices with VOOC protocols (mobile charging stations,
USB plug socket chargers)

Flash Charging Technical Paper

Based on the standards of YDB 195–2018: Technical Requirements and
Test Methods for Fast Charging of Mobile Communication Terminals,
and considering the requirements for different products, four sets of
technical specifications have been drafted:

» TLC 016–2019  Technical Certification Specifications for Fast

Charging VOOC Protocols for Mobile Communication Terminals
and Adaptors

» TLC 017–2019  Technical Certification Specifications for

Fast Charging Adaptors for Mobile Communication Terminals

» TLC 018–2019  Technical Certification Specifications for

car DC power adaptors

» TLC 019–2019  Technical Certification Specifications for

VOOC flash charging cables

Technical
standard Main technical requirement categories

TLC 016–2019 VOOC protocol test requirements

Requirements for interface structures and mechanical functions,

TLC 017-2019 electrical performance, security functions, electromagnetic functions,
environmental adaptability

Requirements for interface structures and mechanical functions,

TLC 018-2019
electrical performance, security functions, environmental adaptability

Interface and cable structure, loop impedance, security functions,

TLC 019-2019
VOOC protocol identification functions

Table 3.1  Technical Certification Specification Requirements System

The following state standards have also become part of the technical
standards for product certification:

» GB 4943.1–2011  Information Technology Equipment-Safety-Part 1:

General Requirements

» GB/T 35590–2017  Information Technology General Specifications

for Portable Digital Equipment Using Power Bank)
 19

Secondary testing and test indicators have been defined (in addition to
the main requirements in Table 3.1), with detailed procedures to clarify 
the scope and process of testing. The aim is to simulate real consumer
use – in the most demanding conditions – to fully check product safety
and certify all types of VOOC accessory. 
3.2.2  Matching Authorisation Mechanism & Standardised 
Certification Process
TLC has drafted certification documentation based on VOOC product

OPPO 
accessory types, complying with the rules and regulations of the China
National Certification and Accreditation Administration Commission.

The certification documentation, product accessory types and technical

Flash Charging Technical Paper

specifications (certification basis) are shown in figure 3.1.

TECHNICAL SPECIFICATION CERTIFICATION IMPLEMENTATION

PRODUCT TYPE
(CERTIFICATION BASIS) REGULATIONS

GB 4943.1-2011 TLC-GZ-P007-5
Mobile power source
Information Technology (contains all-in-one Mobile power source
Equipment-Safety-Part 1: products) products certification
General Requirements implementation regulations

GB/T 35590-2017
Other charging devices TLC-GZ-P007-7
Information Technology
carrying VOOC protocols Fast charging functions
General Specifications for
(mobile charging stations, certification
Portable Digital Equipment
USB plug socket chargers) implementation regulations
Using Power Bank

TLC 017-2019

Technical Certification
AC adaptors
Specifications for Fast (chargers)
Charging Adaptors for Mobile TLC-GZ-P007-4
Compliance with Regulations

Communication Terminals
Fast charging accessory
products certification
TLC 018-2019
implementation regulations
Technical Certification Car DC power
Specifications for car adaptors
DC power adaptors

TLC 016-2019
TLC-GZ-P007-3
Technical Certification
Specifications for Fast Fast charging Fast charging protocol chip
Charging VOOC Protocols for protocol chips certification implementation
Mobile Communication regulations
Terminals and Adaptors

TLC 019-2019 TLC-GZ-P007-6

Technical Certification VOOC flash VOOC flash charging cables

Specifications for charging cables certification implementation
VOOC flash charging cables regulations

Figure 3.1  The Applicable Certification Documentation,

Product Accessory Types and Technical Specifications (Certification Basis)
 20

Application Conditions Must Strictly Match the

Authorisation Requirements. 
The certification applicant must be a legally authorised manufacturer
and the product named in the application must not be outside the
authorised range.

The product and its brand label must clearly show the VOOC protocol
output port and the output specifications. The brand label or

trademark must show it is from an authorised manufacturer and must
not show the label or trademark of an unauthorised manufacturer.

OPPO 
All power adaptors must use a chip manufactured by an authorised chip
manufacturer.

Flash Charging Technical Paper

Key Elements of Certification Revolve Around Key Product
Features.

VOOC accessory certification uses recommended certification mode

No.5 from the International Organisation for Standardisation (ISO):
Type test + initial factory inspection + post-certification supervision
(production factory quality inspection review + factory or
market sampling).

The party organising the type test must separate the units for
certification based on chip model number or circuit structure, and
differences between multiple model numbers in the same certification
unit must also be identified. To refine certification, different units
– or the same certification unit with different model numbers –
are tested separately.

The initial factory inspection – undertaken during a quality check of the

functions, for products with chips – focuses on design and development
resources (and their management), testing of packaging sealed with
tape, verification of VOOC protocol functions and inventory conditions.

For AC adaptors (chargers) and other whole products, the initial factory
inspection focuses on control of purchase of components, manufacture
and testing equipment configuration (and its management), control of
the manufacturing process, quality control of the finished product, and
batch product consistency control.

During the initial factory inspection, samples taken on-site are given a
product consistency check and a visual inspection. The manufacturer’s
actual production facility location is also checked, as well as the
authorisation and quality system documentation (when appropriate).

The post-certification supervision (during the annual review of the

production facility quality system) focuses on the same areas as
the initial factory inspection, as well as checking the consistency of
products.

Using either market purchase samples or samples taken directly

from the manufacturing facility, a re-test checks the key indicators of
verified products, to increase the effectiveness of the inspection.
 21

Certification Process Strictly Follows Established Regulations.

The certification process is conducted stage by stage, based on


certification regulations (including certification fees), and in the form
of documents that are fully accessible to the public. The stages
include certification application, sample inspection, production facility

inspection, and review and issue of certification.

The product sample inspection stage includes closed-loop control of


the processes of laboratory testing and product rectification (where
appropriate), and follows the uniform specifications of test reports. The

OPPO 
on-site inspection stage follows clear regulations for the roles of on-site
inspection personnel, the schedules and content for inspections, and
inspection reports.

Flash Charging Technical Paper

Finally, before the certification is issued, personnel not involved in the
testing – and without conflicts of interest – re-check the output data
from each of the stages outlined above, ensuring the impartiality and
accuracy of the results of the certification process.

3.2.3 Post-certification Monitoring and Authoritative

Issue of Certification Results

Improved Mechanism for Managing

Post-certification Amendments.

A mechanism for managing any post-certification changes for

VOOC product accessories has been developed. This involves checking
documentation and materials, inspecting products and premises
(if necessary), and ensuring that the results of the certification
remain valid. This mechanism could be required for changes to the
manufacturer’s name or address, the key components used, the
production process, the external appearance of the products or
their composition.

Authoritative Issue of Certification Results Platform.

Certified VOOC product accessories and certification information can be

found at the National Certification and Accreditation Information Public
Service Platform of the State Administration for Market Regulation of the
People’s Republic of China and TL Certification Centre Limited Company’s
website.

National Certification and Accreditation Information

Public Service Platform
http://cx.cnca.cn

TL Certification Centre Limited Company’s website

http://www.tlc.com.cn

VOOC product accessories certification documents can be accessed and

read on TL Certification Centre Limited Company’s website.
 22


4 THE FUTURE OF VOOC 

OPPO 
4.1  Development Trend of VOOC Technology

Flash Charging Technical Paper

The arrival of 5G is accelerating the development of the Internet of
Things (including vehicles), VR, AR and numerous other areas, thanks to
low latency, broad connections and greater bandwidth.

But more and more devices are facing mounting friction between
impressive (but power-hungry) features and limited battery capacities.
VOOC Flash Charging can help to address this imbalance – and not just in
smartphones.

Fast charging technology is soon expected to broaden out from phones

to other hardware, such as tablets, watches, laptops, Bluetooth headsets
and more. But it could also support smart home appliances – even
industrial equipment, like automated guided vehicles in warehouses.

And in the future, the standardization of this technology could help

to improve compatibility, meaning one charger is capable of charging
numerous devices.

As users’ charging needs become more abundant, we will see more

diverse modes of charging emerge, with wireless charging expected
to become very popular. But flexibility will be crucial, as the charging
methods at any given moment will be chosen based on what is most
suitable for that scenario – and gives the best charging experience.
Charging adapters will also become more compact and lightweight, with
higher power density. ‘High power, small size’ chargers are one area of
focus for R&D in the near future.

As charging power has continued to increase, heating and safety issues

have become more prominent. At the same time, higher standards are
being put forward for the reliability and power loss of charging systems
too – a key area for ongoing research.
 23

4.2  Summary

The ability to ‘speak for two hours after charging for five minutes’ makes
OPPO’s unique IP remarkable. VOOC Flash Charge technology enables
charge speeds four times faster than normal charging, while using 
universal intelligent device protection, making it one of the fastest and
safest charging technologies available.

Focusing on the core needs of users, VOOC Flash Charging technology
will expand to a wide range of application scenarios and devices. The

OPPO 
aim will be to meet the different charging needs of users in all weathers,
across multiple devices, in any number of situations, and to alleviate the
‘charge anxiety’ of users in the 5G era.

Flash Charging Technical Paper

OPPO will continue to promote the development and use of VOOC Flash
Charging technology, using standardization to guide more companies
towards product compatibility. Working with outstanding partners
across industries, OPPO will license and authorize its patents to expand
the applications and product family of Flash Charging technology. And
it will do so while keeping safety and reliability front of mind, building a
healthy Flash Charging technology ecosystem for years to come.
Flash
Charging globe OPPO Website

twitter OPPO Twitter

the Future linkedin OPPO LinkedIn