AWGPI Prod Info 0722 en-US

Edition 07/2022
PRODUCT INFORMATION
SIMOTION/SIMATIC
Motion Control Encoder
Absolute encoder with PROFINET
Motion Control Encoder PROFINET FS15
www.siemens.com/drives
Introduction 1
Readme/Product
information/Technical 2
update
SIMOTION/SIMATIC
Motion Control Encoder

Product Information
Valid for product version:

Motion Control Encoder PROFINET FS15
Firmware version: V2.x
07/2022
A5E52146185B AA
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage
to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices
referring only to property damage have no safety alert symbol. These notices shown below are graded according to
the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property
damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance
are required to ensure that the products operate safely and without any problems. The permissible ambient
conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication may
be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this
publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG A5E52146185B AA Copyright © Siemens AG 2010 - 2022.

Digital Industries Ⓟ 07/2022 Subject to change All rights reserved
Postfach 48 48
90026 NÜRNBERG
GERMANY
Table of contents
1 Introduction ........................................................................................................................................... 5
2 Readme/Product information/Technical update .................................................................................... 7
2.1 Technical Data ..................................................................................................................... 7
2.1.1 Electrical data ...................................................................................................................... 7
2.1.2 Mechanical data .................................................................................................................. 7
2.1.3 Environmental conditions .................................................................................................... 8
2.2 PROFINET technology......................................................................................................... 10
2.3 Pinning.............................................................................................................................. 11
2.3.1 Electrical connection.......................................................................................................... 11
2.3.2 Status LEDs ........................................................................................................................ 12
2.4 Programmable Parameters ................................................................................................. 14
2.5 Encoder features................................................................................................................ 15
2.6 Mechanical Drawings ......................................................................................................... 16
2.6.1 Synchro flange................................................................................................................... 16
2.6.2 Clamp flange ..................................................................................................................... 17
2.6.3 Hollow shaft ...................................................................................................................... 18
2.6.4 Installation drawings / Dimension drawings........................................................................ 19
2.7 Structure of an order number ............................................................................................. 20
2.8 Accessories and Documentation......................................................................................... 21

Product Information, 07/2022, A5E52146185B AA 3
Table of contents

4 Product Information, 07/2022, A5E52146185B AA
Introduction 1
The absolute encoder (Motion Control Encoder) operates according to one of the following basic
principles:
• Optically scanning a transparent coded disk that is mounted on the drive shaft (singleturn
and multiturn encoders)
• Evaluating a rotating magnetic field that is generated using a magnet (multiturn encoder)
Note
For reasons of simplification, the absolute encoder is simply called "encoder" in the remainder
of this manual.
The encoder has a maximum resolution of 65,536 steps per revolution (16 bit).
In addition, the multiturn version can scan up to 16,384 revolutions (14 bit).
As a consequence, the highest possible absolute resolution is 30 bit = 230 = 1,073,741,824 steps.
The standard singleturn version has a resolution of 16 bit.
The standard multiturn version has a resolution of 30 bit.
Programming the encoder

The encoder equipped with PROFINET interface can be programmed to address user
requirements. The GSDML file belonging to the encoder must be installed on the PLC using the
engineering software tool.
Using the GSMDL file, the resolution per revolution can be configured between 13 and 16 bit.

Introduction

Readme/Product information/Technical update 2
2.1 Technical Data
2.1.1 Electrical data
Data
Power supply 10 – 30 V DC (absolute limits)
Power consumption Max. 3 watts
EMC Emission standard for industrial environments in accordance
with IEC 61000-6-4
Immunity standard for industrial environments in accordance
with IEC 61000-6-2
Bus connection Ethernet
Transmission rate 10/100 Mbits
Maximum cable length: 100 m
Accuracy ± 1 LSB (± 0.0439° for resolution ≤ 13 bits),
± 2 LSB (± 0.0220° for resolution 14 – 16 bits)
Speed Max. 5800 rpm (valid code)
Cycle time 250 µs...100 ms
Electrical service life > 105 h
Parameter storage cycles 50 million
Conformity class C (IRT communication, …), B, A (RT communication)
Addressing Programmable IP address and network parameters
2.1.2 Mechanical data
Data
Enclosure Aluminum
Service life Depending on shaft type and load – see following table
Max. shaft load N <= 6000 rpm: Axial 40 N, radial 110 N
N > 6000 rpm: Axial 10 N, radial 20 N
Moment of inertia of rotor ≤ 30 gcm2
Frictional torque ≤ 3 Ncm
Rpm (continuous duty) Max. 12,000 rpm
Shock (EN 60068-2-27) <= 100 g (half-sine / 6 ms)
Vibration (EN 60068-2-6) 20 g (41 Hz ... 2000 Hz)

Readme/Product information/Technical update
2.1 Technical Data
Data
Weight (standard version) Singleturn: 400 g / 500 g
Net (incl. packaging) Multiturn: 440 g / 540 g
Flange Synchro (F) Clamp (Q) Hollow shaft (W)

Shaft diameter 6 mm 10 mm 8, 10, 12, 15 mm
Shaft length 10 mm 20 mm -
Hollow shaft depth min. / max. - - 15 mm / 30 mm
Minimum (mechanical) service life:
Flange Service life in 108 revolutions with Fa / Fr

40 N / 60 N 40 N / 80 N 40 N / 110 N
Clamp flange 10 x 20 247 104 40
Synchro flange 6 x 10 822 347 133
2.1.3 Environmental conditions
Data
Working temperature range FS: 10 -40 to +75°C
FS: ≥15 -40 to +85°C
Storage temperature range -40 to +70°C
Relative humidity Up to 98 % (without condensation)
Degree of protection ICE Housing side: IP 67
60529 Shaft side: IP 64
IP: International Protection

1st digit: Protection against foreign bodies
2nd digit: Protection against water
• The validity refers to water as medium that can potentially ingress, not to oil or other creeping
fluids.
• It is not permissible for liquid to collect in the flange.
• For applications with the shaft extension facing upward, carefully take into consideration the
protective devices required.

2.1 Technical Data
Installing cables in moist and damp environments

If you are operating the encoder in environments in which moisture can occur, carefully comply
with the following installation instructions
4*&.&/4
4*&.&/4
4*&.&/4 4*&.&/4
Figure 2-1 Permissible and impermissible cable routing when connecting in a damp environment

2.2 PROFINET technology
2.2 PROFINET technology

PROFINET is an Industrial Ethernet standard that merges the system automation with other IT
resources of a company. It provides functionality that is comparable with PROFIBUS along with
technologies that are used by development, IT and administration personnel.
The absolute encoder (Motion Control Encoder) supports the PROFINET V2.33 Standard.
Communication
Communication is realized based on established IT standards: TCP, UDP and IP.
XML is used as a descriptive language for IO device profiles (GSDML files).
More information
More information on the principle of operation and setting up a PROFINET network are provided
at the following address:

2.3 Pinning
2.3 Pinning
2.3.1 Electrical connection

The encoder is connected using one 4-pole M12 connector for the power supply and two 4-pole
D-coded M12 connectors for Ethernet.
The encoder uses a second D-coded connector and provides an integrated switch function. The
installation instructions are located on or in the connector packaging.
Adapters for the field wiring can be ordered.
More information is provided in the catalog: SINAMICS S120 and SIMOTICS - Catalog D 21.4
(https://support.industry.siemens.com/cs/document/109747019/catalog-d-21-4%3A-
sinamics-s120-and-simotics?dti=0&lc=en-WW)
Connector for Ethernet connection
Pin number Signal

1 Tx +
2 Rx +
3 Tx -
4 Rx -
Figure 2-2 4-pole, socket, D-coded

2.3 Pinning
Connector for the power supply
Pin number Signal

1 V+ (10 - 30 V DC)
2 N. C.
3 GND (0 V)
4 N.C.
Figure 2-3 4-pole, plug connector, A-coded
2.3.2 Status LEDs
Figure 2-4 LED display - rear side of the encoder housing
Table 2-1 Significance of the diagnostics LED
LED Color Description for LED = on

Active1 Yellow Incoming and outgoing data traffic via port 1
Link1* Green Connection to another Ethernet component via port 1
Active2 Yellow Incoming and outgoing data traffic via port 2
Link2* Green Connection to another Ethernet component for port 2
Stat1 Multicolor Communication status
More information is provided in the subsequent table: LED status display
Stat2 Multicolor Encoder status
More information is provided in the subsequent table: LED status display
*Flashes at 2 Hz if flashing is activated via the engineering and a connection is available

2.3 Pinning
Table 2-2 LED status display
Status 1 Status 2 Meaning Cause

Two color Two color
Off Off No power supply • Fuse defective
• Cable defective
Red Green No connection to another device • Bus disconnected
Criterion: No data exchange • IO controller not available
• IO controller switched off
• IO controller not operational
Flashes 1)
Green Parameterization error, no data • IO device not configured or incor‐
Red exchange rect configuration
Criteria: Connection available. • Incorrect participant (node) ad‐
As a result of incorrect parameter‐ dress assigned; however, not out‐
ization, the IO device had not side the permissible range
changed into the data exchange
• Actual configuration of the IO de‐
mode.
vice deviates from the target con‐
figuration
Green Red System error • Class error diagnostics available
Malfunction (error) in the encod‐ • Device in the data exchange
er application process. mode
Green Red/green System alarm • Diagnostics of the class alarm and
Alarm in the encoder application no class error active.
process. • Device in the data exchange
mode
Green Green Data exchange
IO device and operation OK
1)
The flashing frequency is 0.5 Hz. The minimum display duration is 5 s

2.4 Programmable Parameters
2.4 Programmable Parameters

The encoder supports application Class 3 and Class 4 functions. You can set additional functions
using the GSDML file.
Parameter Description
Counting direction Parameter "Counting direction" defines whether the counter value increa‐
ses or decreases if the shaft rotates clockwise
Resolution per revolution Parameter "Resolution per revolution" is used to program the required
number of pulses per revolution. Any value between 1 and the physical
resolution per revolution can be programmed.
Total resolution This parameter is used to program the required number of count pulses
(steps) over the complete measuring range. This value must not exceed
the overall physical resolution of the absolute rotary encoder.
Preset value The "Preset value" is the position value required, which should be reached
at a certain physical position of the axis. The position value is set by pre‐
setting the parameter to the required process value.
Velocity The software that has been implemented can also specify the actual ve‐
locity. This value is transferred in the form of binary code together with the
process value.
One of four units can be selected: Pulses (steps) per 10 ms, per 100 ms, per
1000 ms and revolutions per minute
More information on parameterization is provided in the Operating Instructions:

Motion Control Encoder, Absolute Rotary Encoder with PROFINET

2.5 Encoder features
2.5 Encoder features

Encoder with application Class 4 supports all functions of an encoder with application Class 3.
Further, using telegram 860, the encoder can also be used in applications where functions
according to Class 1 and Class 2 are required.
Basic functions
• PROFINET V2.33 communication interface
• Cycle time ≥ 250 µs
• MRP for RT (media redundancy)
• MRPD for IRT (bumpless media redundancy)
• Absolute encoder (singleturn or multiturn depending on the version)
• Class 3, Class 4 (IRT)
• Class 1, Class 2 (RT or IRT)
• PROFINET neighborhood detection (for device replacement without engineering)
• Device identification using LEDs
• Support of encoder profile V4.2
• Emulation of encoder profile V3.1 (compatibility mode)
• Replacement part compatibility to encoders V4.2 and V4.1
• Support of standard telegrams 81, 82, 83, 84, 86, 87, 88, 89
• Support of manufacturer-specific telegrams 860, 862
• Support of the PROFIdrive parameter channel (acyclic communication)
• Speed/velocity value with configurable filter settings and units
• Acceleration value
• Integrated rotary axis function (endless shaft)
• Scaling function with fractional arithmetic scaling
• PROFIdrive fault memory as diagnostics logbook (for errors and alarms)
• Standard PROFINET diagnostics (alarm channel)
• Operating hours counter
• Integrated bootloader to upgrade the encoder firmware

2.6 Mechanical Drawings
2.6.1 Synchro flange
Overview
4JOHMF.VMUJ
#
Yp Y.࠳
¸
q
q ¸
#
¸G
¸G
¸

¸
Mounting suggestion
¸ " Y. Y¸

Y. ¸ "
Y.
p
p

Y
Y
¸ ¸' " ¸ ࣧ¸

$MBNQJOHKBXT ¸'
"
'9,1
*M3 Md = 1.1 - 1.3 Nm

**M4 Md = 2.4 - 2.9 Nm
Standard metric thread according to DIN 13, property class 8.8

2.6.2 Clamp flange
Overview
4JOHMF.VMUJ

Y.࠳
Y.࠳
¸I
¸ ¸

¸G
Yp
¸
¸
Y

p

¸
Mounting suggestion
Y<..> Y<¸¸>
¸ "
.Eࣧ/N
p

Y
¸
¸) ¸
"
M4 Md = 2.4 - 2.9 Nm
*M3 Md = 1.1 - 1-3 Nm
Standard metric thread according to DIN 13, property class 8.8

2.6.3 Hollow shaft
Overview
% ¸
4JOHMF.VMUJ

¸
¸
¸
p

¸
*OTUBMMBUJPOFEHF
BUUIFUPSRVF
BSN

¸
.BY8
.JO8
Figure 2-5 ** Insertion depth into the shaft
Inside diameter D Shaft diameter (D1)

15F7 15f8
With reduction sleeve 12F7 12f8
Note
Mounting instructions
It is only permissible to tighten the clamping ring if the shaft of the drive element is inserted in
the hollow shaft of the encoder.
Using a reducer, the hollow shaft diameter can be adapted to 12 mm, 10 mm or 8 mm. This
reducer is simply inserted into the hollow shaft.

Connection dimensions on the customer side
¸q "
"
"
NN
%
ࣧ
ࣨ
Y.࠳ ࣧ
2.6.4 Installation drawings / Dimension drawings

Additional dimension drawings are provided in the DT CONFIGURATOR online.
DT CONFIGURATOR
You can find the following quickly and simply in the DT CONFIGURATOR:
• Dimension drawings
• 2D/3D CAD data
The DT CONFIGURATOR supports you when creating system documentation regarding project-
specific information.
Note
Simplified representation
The 3D model in the DT CONFIGURATOR is a simplified representation that does not show every
detail.
More information is provided on the Internet at: DT CONFIGURATOR (http://siemens.de/dt-

konfigurator)

2.7 Structure of an order number
2.7 Structure of an order number
Overview
'9 Y/YY

&ODPEFS
"CTPMVUF
'ࣜ4ZODISP꫽BOHF
2ࣜ$MBNQ꫽BOHF
8ࣜ)PMMPXTIBGU
/ࣜ130'*/&5
1ࣜ130'*#64
3FTPMVUJPO
ࣜ4JOHMFUVSO
ࣜ.VMUJUVSO

2.8 Accessories and Documentation
Cables and connectors
Line connecting cable

Prefabricated power supply cable for PROFINET IO absolute encod‐
ers, with M12 connectors and M12 socket, A-coded, 4-pole
• Length: 2 m • 6XV1801-5DH20
• Length: 3 m • 6XV1801-5DH30
• Length: 5 m • 6XV1801-5DH50
• Length: 10 m • 6XV1801-5DN10
• Length: 15 m • 6XV1801-5DN15
IE connecting cable
Prefabricated signal cable for PROFINET IO absolute encoder with
M12 and RJ45 connectors, D-coded, 4-pole
• Length: 2 m • 6XV1871-5TH20
• Length: 3 m • 6XV1871-5TH30
• Length: 5 m • 6XV1871-5TH50
• Length: 10 m • 6XV1871-5TN10
• Length: 15 m • 6XV1871-5TN15
IE FC RJ45 connector 145 (1 unit)

6GK1901-1BB30-0AA0
2 × 2 RJ45 connectors with rugged metal housing and FC connection
system, 145° cable outlet
IE FC M12 connector PRO (1 unit)

6GK1901-0DB20-6AA0
M12 connector with metal housing and FC connection system, axial
cable outlet, D-coded
IE FC TP cable for cable carriers 2 × 2 (type C)

6XV1840-3AH10
4-conductor, shielded, PROFINET-compatible TP installation cable for
use in cable guides, sold by the meter
Max. shipping quantity: 2000 m
Minimum order quantity: 20 m

More information
More information on the implementation and configuration of the absolute rotary encoder with
PROFINET interface is provided in the
Operating Instructions Absolute Rotary Encoder with PROFINET

More information
Siemens:
www.siemens.com
Industry Online Support (service and support):
www.siemens.com/online-support
IndustryMall:
www.siemens.com/industrymall
Siemens AG
Digital Industries
Motion Control
Postfach 3180
91050 Erlangen
Germany

AWGPI Prod Info 0722 en-US

Uploaded by

Copyright:

Available Formats

AWGPI Prod Info 0722 en-US

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

AWGPI Prod Info 0722 en-US

Uploaded by

Copyright:

Available Formats

Edition 07/2022

Motion Control Encoder

Valid for product version:

Siemens AG A5E52146185B AA Copyright © Siemens AG 2010 - 2022.

Absolute encoder with PROFINET

Absolute encoder with PROFINET

Programming the encoder

Absolute encoder with PROFINET

Absolute encoder with PROFINET

2.1.1 Electrical data

2.1.2 Mechanical data

Absolute encoder with PROFINET

Flange Synchro (F) Clamp (Q) Hollow shaft (W)

Minimum (mechanical) service life:

Flange Service life in 108 revolutions with Fa / Fr

2.1.3 Environmental conditions

IP: International Protection

Absolute encoder with PROFINET

Installing cables in moist and damp environments

Absolute encoder with PROFINET

2.2 PROFINET technology

Absolute encoder with PROFINET

2.3.1 Electrical connection

Connector for Ethernet connection

Pin number Signal

Absolute encoder with PROFINET

Connector for the power supply

Pin number Signal

2.3.2 Status LEDs

Figure 2-4 LED display - rear side of the encoder housing

Table 2-1 Significance of the diagnostics LED

LED Color Description for LED = on

Absolute encoder with PROFINET

Table 2-2 LED status display

Status 1 Status 2 Meaning Cause

Absolute encoder with PROFINET

2.4 Programmable Parameters

More information on parameterization is provided in the Operating Instructions:

Absolute encoder with PROFINET

2.5 Encoder features

Absolute encoder with PROFINET

2.6 Mechanical Drawings

2.6.1 Synchro flange

¸ " Y. Y¸

¸ ¸' " ¸ ࣧ¸

*M3 Md = 1.1 - 1.3 Nm

Absolute encoder with PROFINET

2.6.2 Clamp flange

Absolute encoder with PROFINET

2.6.3 Hollow shaft

Figure 2-5 ** Insertion depth into the shaft

Inside diameter D Shaft diameter (D1)

Absolute encoder with PROFINET

Connection dimensions on the customer side

¸q  "

2.6.4 Installation drawings / Dimension drawings

More information is provided on the Internet at: DT CONFIGURATOR (http://siemens.de/dt-

Absolute encoder with PROFINET

2.7 Structure of an order number

¸ " Y. Y¸

¸ ¸' " ¸ ࣧ¸

¸q "

'9 Y/YY