m1 Pressure Gauge  PSI 

„„ACCURACY
ALL DIMENSIONS IN MM (IN) 43.7
Ø 106.2 (1.72)
(Ø 4.18)
0 to 20% of Range: ±(0.04% of Full Scale) Includes all effects of linearity, hysteresis, repeatability,
temperature, and stability for two years.
20% to 110% of Range: ±(0.2% of Reading)
All models indicate vacuum, but vacuum specification applies 300 PSI
Vacuum: ±(0.25% of Full Scale*) to 30 PSI, 100 PSI, and 300 PSI models only. 123.2
(4.85)
* Full Scale = -14.5 PSIG
Not recommended for continuous use below -14.5 PSI.
Refer to XP2i-DP data sheet for gauges that are intended for
continuous high vacuum use.

„„OPERATING TEMPERATURE
Temperature Range: -10 to 50° C (14 to 122° F) Non-condensing. No change in accuracy over operating
temperature range. Gauge must be zeroed to achieve rated 70.2
specification. (2.76)
SENSOR

„„DISPLAY 23.6
DIAPHRAGM
SURFACE
Screen: 5 digits, 16.8 mm (0.66") high LCD readable in sunlight with bright backlight. (0.93) 19 (3/4")
WRENCH HEX
Display Rate: 4 readings/second
7/16-20 MP CPF PORT
21.7
INTERNAL PRESSURIZED VOLUME:
„„
(0.86)
POWER 295 mm3 (0.02 in3)
2 x AA: 900 hours, typical Uses 2 alkaline AA (LR6) batteries. Use of backlight reduces
1/4 INCH MNPT 1/4 INCH MBSP M20X1.5
operating time. Extended battery life is keypad selectable. Do ADAPTER ADAPTER ADAPTER
Extended Battery Life: 1 reading/15 seconds: 3,000 hours not overtighten rear cover when replacing batteries.

1 reading/30 seconds: 6,000 hours

1 reading/60 seconds: 10,000 hours

1 reading/5 minutes: 25,000 hours 29.1 26.1
(1.03) 32.6
(1.15) (1.30)

1 reading/10 minutes: 30,000 hours

ADDITIONAL SENSOR LENGTH WITH OPTIONAL FITTING ADAPTERS

4725.C  m1 PSI Data Sheet Page 1 of 3

 m1 Pressure Gauge  PSI 

„„ENCLOSURE „„CERTIFICATIONS
Weight: 331 g (11.7 oz) Weight includes batteries and protective boot. m1 complies with the Electromagnetic Compatibility
Rating: IP65 Water resistant housing incorporating o-ring seals [IEC 60529]. and Pressure Equipment Directives. Refer to the EC Declaration
LCD protected from impact damage by polycarbonate lens under
of Conformity for specific details.
Housing: Polyester/Polycarbonate Blend
polyester window.
Keypad and Labels: UV Resistant Polyester m1 is approved for use as a portable test instrument
Skydrol® compatible.
for Marine use and complies with Det Norsjke Veritas’ Rules

„„SENSOR for Classification of Ships, High Speed & Light Craft, and
Offshore Standards.
Wetted Materials: (wrench tight) 316 stainless steel All welded, with a permanently filled diaphragm seal.

(finger tight) 316 stainless steel Metal to metal cone seal; O-ring can be removed if necessary.
and Viton® (internal o-ring) 1/4” medium pressure tube system compatible with HiP LM4 and
LF4 Series, Autoclave Engr SF250CX Male and Female Series.
Diaphragm Seal Fluid: Dow Corning® 200
1/4" male NPT adapter included unless BSP or M20 is specified.
Connection: Crystal CPF Female
Can be cleaned and certified for oxygen service.

„„STORAGE TEMPERATURE
Temperature Range: -40 to 75° C (-40 to 167° F) Batteries should be removed if stored for more than
one month.

„„SPECIAL FEATURES
Averaging: Smooths unsteady readings (2 to 20 samples)
Vertical Bar Graph: Percent pressure indication for quick reference
Capture: Minimum (LO) and Maximum (HI)

4725.C  m1 PSI Data Sheet Page 2 of 3

 m1 Pressure Gauge  PSI 

„„RANGE & RESOLUTION TABLE „„ACCESSORIES

Protective Boot P/N 3436 (included)
Display Resolution
Range Over- in in mm mm
Protect your m1 from harsh environments with our form
P/N PSI kg/cm2 bar mbar kPa MPa
(PSI) pressure H2O Hg Hg H2O fitting chemical resistant thermoplastic boot (Skydrol
30PSI 30 3.0 x 0.001 0.1 0.01 0.1 1 0.0001 0.0001 0.1 0.01 fluid compatible).
100PSI 100 2.0 x 0.01 0.1 0.01 1 0.001 0.001 1 0.1 0.0001
300PSI 300 2.0 x 0.01 0.1 1 0.001 0.001 1 0.1 0.0001
1KPSI 1000 2.0 x 0.1 0.1 0.01 0.01 1 0.001
3KPSI 3000 1.5 x 0.1 1 0.01 0.01 1 0.001 „„COMPLIMENTARY PRODUCTS
10KPSI 10 000 1.5 x 1 1 0.1 0.1 0.01 Crystal Engineering offers a wide range of products that
work with the m1:

• Fittings that connect without tools, safely and without leaks

„„
ORDERING INFORMATION • Lightweight, super flexible high pressure hoses
Adapter: Oxygen
• Fitting kits and adapters
Model — P/N
Type Service? • Pneumatic hand pumps
M1 • Hydraulic hand pumps
• Portable pressure comparators
Standard: NPT: (omit) No: (omit)

Optional: G 1/4 B: -BSP Yes: -O Dow Corning is a registered trademark of Dow Corning Corporation.

M20x1.5: -M20

SAMPLE PART NUMBERS

M1-300PSI. . . . . . . . . . . . . . . . . 300 PSI standard gauge, with a 1/4" NPT pressure fitting
M1-1KPSI-BSP-O. . . . . . . . . 1000 PSI gauge, with a 1/4" BSP pressure fitting and Oxygen Service options

© 2012 Crystal Engineering Corporation

708 Fiero Lane, Suite 9, San Luis Obispo, California 93401-8701

crystalengineering.net 4725.C  m1 PSI Data Sheet Page 3 of 3