PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO

INSTALLATION AND OPERATION. BY PROCEEDING YOU AGREE THAT YOU

FULLY UNDERSTAND AND COMPREHEND THE FULL CONTENTS OF THIS
MANUAL. FORWARD THIS MANUAL TO ALL OPERATORS. FAILURE TO
REV 7/30/07 OPERATE THIS EQUIPMENT AS DIRECTED MAY CAUSE INJURY OR DEATH.

INSTALLATION AND OPERATION MANUAL

MODEL:
RX-950 / 950AT
TIRE CHANGER
FOR SERVICING
AUTOMOBILE
AND LIGHT TRUCK
SINGLE PIECE
TIRES / WHEELS

Keep this operation manual near the

machine at all times. Make sure that
ALL USERS read this manual .

SHIPPING DAMAGE CLAIMS BE SAFE

When this equipment is shipped, title passes to the Your new Ranger tire changer was designed
purchaser upon receipt from the carrier. and built with safety in mind. However, your
Consequently, claims for the material damaged in overall safety can be increased by proper
shipment must be made by the purchaser against the training and thoughtful operation on the part of
transportation company at the time shipment is the operator. DO NOT operate or repair this
received. equipment without reading this manual and the
important safety instructions shown inside.

1645 Lemonwood Dr.

Santa Paula, CA. 93060, USA
Tel: 1-805-933-9970
Fax: 1-805-933-9160
 RX-950 / 950AT
TIRE CHANGER

This instruction manual has been prepared especially for you.

Your new tire changer is the result of over 25 years of continuous research, testing
and development and is the most technically advanced tire changer on the market today.
The manner in which you care for and maintain your tire changer will have a
direct effect on it's overall performance and longevity.

READ THIS ENTIRE MANUAL

BEFORE OPERATION BEGINS.
RECORD HERE THE FOLLOWING INFORMATION
WHICH IS LOCATED
ON THE SERIAL NUMBER DATA PLATE.

Serial No. __________

Model No. __________

Manufacturing date __________

PRODUCT WARRANTY
Your new tire changer is warranted for one year on equipment structure; one year on all operating components and tool-
ing/accessories, to the original purchaser, to be free of defects in material and workmanship. The manufacturer shall repair
or replace at their option for this period those parts returned to the factory freight prepaid which prove upon inspection to
be defective. The manufacturer will pay labor costs for the first 12 months only on parts returned as previously described.

The warranty does not extend to...

 defects caused by ordinary wear, abuse, misuse, shipping damage, improper installation, voltage or lack of
required maintenance;
 damages resulting from purchaser’s neglect or failure to operate products in accordance with instructions
provided in the owner’s manual(s) and/or other accompanying instructions supplied;
 normal wear items or service normally required to maintain the product in a safe operating condition;
 any component damaged in shipment;
 other items not listed but may be considered general wear parts;
 damage caused by rain, excessive humidity, corrosive environments or other contaminants.

THESE WARRANTIES DO NOT EXTEND TO ANY COSMETIC DEFECT NOT INTERFERING WITH EQUIPMENT
FUNCTIONALITY OR ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT
MAY RESULT FROM ANY DEFECT, FAILURE, OR MALFUNCTION OF A BENDPAK INC./ RANGER PRODUCT OR
THE BREACH OR DELAY IN PERFORMANCE OF THE WARRANTY.

WARRANTY IS NOT VALID UNLESS

WARRANTY CARD IS RETURNED.
2
 TABLE OF CONTENTS
Page #

Definitions of Hazard Levels ..............................4

Failure to follow danger, warning, and caution instructions
Owner’s Responsibility .......................................4 may lead to serious personal injury or death to operator or
bystander or damage to property.
Introduction / Safety Instructions ........................5

Tire and wheel Service Safety Instructions .........6 Do not operate this machine until you read and understand
all the dangers, warnings and cautions in this manual.
Description of Parts ............................................7

Specifications......................................................7 For additional copies

or further information, contact:
Lifting / Unpacking Instructions..........................8 Bend-Pak Inc. / Ranger Products
Installation ..........................................................8 1645 Lemonwood Dr.,
Santa Paula, CA. 93060
Wiring Instructions ............................................10 1-805-933-9970
www.bendpak.com
Operating Instructions ......................................11 www.rangerproducts.com
Bead Loosening and Demounting ...............11-15

Mounting ....................................................15-17

Inflation ......................................................17-21

Wheel Restraint.................................................19 OPERATOR PROTECTIVE EQUIPMENT

Bead Sealing ...................................................19 Personal protective equipment helps make tire changing
safer. However, equipment does not take the place of safe
Bead Seating ....................................................20
operating practices. Always wear durable work clothing
Custom, and Aluminum Wheels .......................15 during tire service activity. Shop aprons or shop coats may
also be worn, however loose fitting clothing should be
Tube Type Tires .........................................15/17 avoided.Tight fitting leather gloves are recommended to
protect operators hands when handling worn tires and
Mis-Matched Tires and Wheels ...................20 wheels. Sturdy leather work shoes with steel toes and oil
Maintenance Instructions ............................21-22 resistant soles should be used by tire service personnel to
help prevent injury in typical shop activities.
Critical Safety Warnings/Instructions ................24 Eye protection is essential during tire service activity.
Safety glasses with side shields, goggles, or
Maintenance Notes /Records............................25 face shields are acceptable. Back belts pro-
vide support during lifting activities and are
Service Parts ..............................................26-44
also helpful in providing operator protection.
Options / Accessories ...............................45-46 Consideration should also be given to the
use of hearing protection if tire service activity is performed
in an enclosed area, or if noise levels are high.

THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH IF NOT FOLLOWED
COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS
AND CAN CAUSE PERSONAL INJURY OR DEATH. READ AND FOLLOW ALL INSTRUCTIONS IN
THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
3
 DEFINITIONS OF OWNER’S RESPONSIBILITY
HAZARD LEVELS
To maintain machine and user safety, the responsibility of
Identify the hazard levels used in this manual with the the owner is to read and follow these instructions:
following definitions and signal words:
 Follow all installation instructions.

 Make sure installation conforms to all applicable Local,

State, and Federal Codes, Rules, and Regulations; such as
DANGER State and Federal OSHA Regulations and Electrical Codes.
Watch for this symbol: It Means: Immediate hazards which
will result in severe personal injury or death.  Carefully check the unit for correct initial function.

 Read and follow the safety instructions. Keep them

readily available for machine operators.

 Make certain all operators are properly trained, know

WARNING how to safely and correctly operate the unit, and are
Watch for this symbol: It Means: Hazards or unsafe properly supervised.
practices which could result in severe personal injury or
death.  Allow unit operation only with all parts in place and
operating safely.

 Carefully inspect the unit on a regular basis and perform

all maintenance as required.
CAUTION
Watch for this symbol: It Means: Hazards or unsafe  Service and maintain the unit only with authorized or
practices which may result in minor personal injury or approved replacement parts.
product or property damage.
 Keep all instructions permanently with the unit and all
decal's on the unit clean and visible.

Do not attempt to operate this equipment if you have never

Watch for this symbol! It means BE ALERT! Your safety, or
been trained on basic tire service and mounting /
the safety of others, is involved!
dismounting procedures.

4
IMPORTANT SAFETY INSTRUCTIONS 11. DANGER! The motor on this machine contains high
Read these safety instructions entirely!
voltage. Disconnect power at the recep-
tacle before performing any electrical
repairs. Secure plug so that it cannot be
accidentally plugged in during service.
1. READ AND UNDERSTAND all safety warning pro-
cedures before operating lift. 12. WARNING! RISK OF EXPLOSION. This equip-
ment has internal arcing or sparking
2. KEEP HANDS AND FEET CLEAR. Remove hands parts which should not be exposed to
and feet from any moving parts. flammable vapors. This machine should
not be located in a recessed area or
3. KEEP WORK AREA CLEAN. Cluttered work areas below floor level.
invite injuries.
13. MAINTAIN WITH CARE. Keep unit clean for better
4. Consider work area environment. Do not expose and safe performance. Follow manual for proper lubri-
equipment to rain . DO NOT use in damp or wet loca- cation and maintenance instructions. Keep control ped-
tions. Keep area well lighted. als and/or buttons dry, clean and free from grease and
oil.
5. ONLY TRAINED OPERATORS should operate this
equipment. All non-trained personnel should be kept 14. STAY ALERT. Watch what you are doing. Use com-
away from work area. Never let non-trained personnel mon sense. Be aware.
come in contact with, or operate machine.
15. CHECK FOR DAMAGED PARTS. Check for condi-
6. USE MACHINE CORRECTLY. Use machine in the tion of all moving parts, breakage of parts or any condi-
proper manner. Never use adapters other than what is tion that may affect the machines operation. Do not use
approved by the manufacturer. if any component is broken or damaged.

7. DO NOT override or disable safety valves and/or 16. NEVER remove safety related components or
devices. device from the machine. Do not use if safety related
components are damaged or missing.
8. ALWAYS INSURE that the safeties are engaged
17. To reduce fire hazard, keep engine/motor exteri-
before any attempt is made to work on or near vehicle.
or free of oil, solvent, or excessive
grease.
9. DRESS PROPERLY. Non-skid steel-toe footwear is
recommended when operating machine.

18. Unreadable and missing warning labels must be

10. GUARD AGAINST ELECTRIC SHOCK. This equip-
replaced immediately. Do not use the tire changer if
ment must be grounded while in use to protect the oper- one or more labels are missing. Do not add any
ator from electric shock. Never connect the green power object that could prevent the operator from seeing
cord wire to a live terminal. This is for ground only. the labels.

5
 TIRE AND WHEEL SERVICE NEVER mount a tire on a damaged or rusty wheel as tire or
wheel failure may result during inflation. Explosion from
SAFETY INSTRUCTIONS failure may result in severe injury or death of the operator
and bystanders.

Inflation
Only properly trained personnel should service tires and ALWAYS be sure the bead opposite the tool is in the drop
wheels on the RX-950/ 950AT. Read all safety and operat- center before rotating the tire when demounting or mounting
ing instructions thoroughly before use. The following safety to avoid damage to the tire beads.
instructions are for one piece wheels only. Always refer to
the manufacturer’s procedures for multi-piece wheels. ALWAYS follow all applicable Local, State, and Federal
Codes, Rules, and Regulations; such as the Federal OSHA
Always wear durable personal protective work clothing and Standard Number 1910.177.
safety gear during tire service activity. Refer to page three
for Operator Protective Equipment. ALWAYS use an approved inflation chamber or inflation
cage equipped with a self-gripping chuck and remote
ALWAYS remove all wheel weights and the valve core to inflation gauge and valve.
deflate the tire before servicing.
ALWAYS inflate the tire to manufacturer’s recommended
ALWAYS keep all working surfaces clean and free of debris. cold operating pressure.

ALWAYS be aware of what each person is doing-- and will DO NOT OVER INFLATE! Tire or wheel failure during and
do before attempting any two-person operation. after inflation may result in an explosion capable of causing
severe injury or death.
ALWAYS cover the electric motor and switch box before
hosing down the tire changer. Be sure water does not enter NEVER reinflate a tire that has been run underinflated or flat
the motor or switch box. without first demounting the tire and checking for wheel and
tire damage.
ALWAYS disconnect the electric power and air supply
before attempting any maintenance. ALWAYS inspect the tire interior for loose or broken cords,
cuts, penetrating objects, and other damage. Discard tires
that cannot be properly repaired.
Bead Loosening
NEVER place anything between the bead loosener disc and NEVER rework, weld, heat or braze wheels.
the tire/wheel.
NEVER strike the tire or wheel with a hammer.
NEVER allow the bead loosener disc to contact the wheel
or wheel damage may occur. ALWAYS be sure the tire diameter exactly matches the
wheel diameter.
NEVER place any part of your body between the bead
loosener disc and the tire/wheel, severe bodily injury may
result.

Demounting & Mounting

ALWAYS clean and inspect the wheel prior to any service.

NEVER stand on the sliding carriage, frame or work table

while demounting or mounting a tire. Tire failure under pressure can be hazardous. When possi-
ble, always place wheels inside an approved inflation
ALWAYS keep hands, feet, and other objects away from chamber or cage before inflating. Use an approved remote
moving parts while the machine is turned on. inflation valve, hose, and gauge. ALWAYS wear safety
goggles for eye protection. Do not stand beside the wheel
ALWAYS place the narrow bead seat to the outside when or cage during inflation. Keep hands and other parts of the
clamping. Failure to demount the tire from the narrow bead body out of the cage during inflation. Observe the tire pres-
seat side may cause damage to the tire beads. sure frequently. Do not exceed the manufacturer’s recom-
mended maximum inflation pressure. Failure to follow
ALWAYS apply an approved rubber lubricant to rim flanges these instructions may cause the tire and rim to separate
and both tire beads before demounting or mounting and with tremendous force, resulting in serious personal injury
seating the beads. or death.

6
 DESCRIPTION OF PARTS
1. Vertical Slide
2. Swing Arm
3. Swing Arm Adjustment Knob
4. Vertical Slide Lock Lever
5. Mount / Demount Head
6. Tower
7. Turntable
8. Jaw / Clamp
9. Bead Breaker Arm
10. Bead Breaker Blade
11. Bead breaker Pads
12. Lube Bottle
13. Foot Pedal / Jaw Control
14. Foot Pedal / Bead Breaker
15. Foot Pedal / Turntable Rotation
16. Bead Lifting Bar
17. Jet-Blast Nozzle
18. Air Hose
19. Voltage Selector Switch

FEATURES / SPECIFICATIONS
MODEL RX950/ 950 AT
Type of wheels................Aluminum, Special Alloys, Steel Breaker Bar.......................................................Standard
Type of Drive System................................... Electric & Air Soap / Lubricator Bucket...................................Standard
Motor...........................................1-1/2 HP (110-220 VAC) Brush .............................................................Standard
Air Requirement..........................110-175 PSI (8-10 BAR) Cross Cut Table Top..........................................Standard
Wheel Clamping Method.. ...4 Clamps - Internal / External Adjustable “Jet-Blast” Bead Seating System.... Standard
Table Clamping System............Dual Pneumatic Cylinders Internal Rim Clamping...12-1/2" – 22" (317 mm – 559 mm)
Bead Breaking System.....Dual Positional Pneumatic Blade External Rim Clamping...11-1/2" – 21" (292 mm – 533 mm)
Inflation Gauge....................................................Standard Tire Width / Bead Breaking .... 3" – 14" (76 mm – 355 mm)
Water Filter..........................................................Standard Tire Width Capacity / Table.............................14" (356 mm)
Oiler / Lubrication ..................................................Standard Maximum Tire Diameter...............................50" (1270 mm)
Air Regulator..........................................................Standard Shipping Weight.......................................642 lbs. (291 Kg)
7
 LIFTING Machine size is approximately:
48” x 48 “ RX-950
48” x 60” RX-950AT
Handling of the machine must be performed only with an
appropriate lifting device such as a forklift or pallet jack.

Only personnel who are experienced and qualified on

material handling procedures should handle any
transportation or moving of machine.

Uncrating Instructions
Carefully remove the crating and packing materials and all
skid and pallet fasteners.

Be careful when cutting steel banding material as items may

become loose and fall causing personal harm or injury.
Always wear gloves when uncrating the machine to
prevent scratches, abrasions, or cuts due to the contact with
packing materials. Remember to report any shipping dam-
age to the carrier and make a notation on the delivery
receipt.

INSTALLATION
Disconnect tag and lock out power source
before attempting to install, service, relocate or
perform any maintenance.

Do not lift or move unit without appropriately rated

equipment. Be sure the unit is securely attached
to lifting device used.

Never use the wood shipping skid for mounting

the unit.
8
 AIR SOURCE
This model requires a 14 to 15 CFM air source at 150 PSI
minimum pressure. The safe operating pressure range for
this model is between 110 PSI and 175 PSI at the machine.
The unit is furnished with a 1/4" pipe thread male fitting for
easy connection. This connection is located on the right side
of the rear of the machine. A 1/4" ID hose (or pipe) for
connection to the machine is satisfactory. Sufficient air
pressure assures good performance. (See Fig. 2)

Fig. 2

These measurements are the tire changer's working

range. Persons other than specially trained and authorized ELECTRICAL SOURCE
operators are expressly forbidden to enter this area.
This unit requires power from a 15 amp electrical circuit.
Choose a safe location that is in compliance with current Refer to the serial tag of the machine for specific electrical
work place safety regulations. Failure to properly install the requirements. Have a licensed electrical technician perform
machine can lead to improper and unsafe operation. any necessary changes to the power source before
plugging in the unit. The electrical source must have a solid
connection between ground and building ground.

MOUNTING
It is not essential to anchor the machine to the floor,
however, the floor must be smooth and level and permit the
platform rollers to move freely. When anchoring to a
concrete floor use the mounting holes that are provided in GUARD AGAINST ELECTRIC SHOCK. This equipment must
the frame. Make sure the machine is solid and level and be grounded while in use to protect the operator from electric
supported evenly on all anchor points. Solid shims may be shock. Never connect the green power cord wire to a live
used if necessary. (See Fig. 1) terminal. This is for ground only.

Fig. 1

DANGER! The motor on this machine contains high voltage.

Disconnect power at the receptacle before performing any
electrical repairs. Secure plug so that it cannot be accidentally
plugged in during service.

WARNING! RISK OF EXPLOSION. This equipment has

internal arcing or sparking parts which should not be exposed
to flammable vapors. This machine should not be located in a
recessed area or below floor level.
9
 WIRING INSTRUCTIONS

1. Check the voltage, phase and proper amperage requirements for the motor shown on the motor plate. Wiring should
be performed by a certified electrician only.

2. Overheating, short circuits and fire damage will result from inadequate wiring. Wiring must be installed in accordance
with National Electric Code and local codes and standards
covering electrical apparatus and wiring.

3. Be certain that adequate wire sizes are used, and that:

 Service is of adequate amp rating.

 The supply line has the same electrical characteristics (voltage, cycles and phase) as the motor.

 The line wire is the proper size and that no other equipment is operated from the same line. The chart below gives
minimum recommended wire sizes for compressor installations.

Check the voltage, phase and proper amperage requirements for the motor shown on the motor plate. Wiring should be
performed by a certified electrician only.

IMPORTANT NOTE:
YOUR MACHINE HAS A DUAL VOLTAGE MOTOR and can be run on either 110 or 220 volts.
STANDARD WIRING IS 110 VOLTS.
See below before connecting 220 volts to your machine or serious damage to the motor/electronics will result.
Confirm voltage selector switch is positioned correctly before connecting power to your machine or serious damage to the
motor/electronics will result. (See Fig. 1).

Fig. 1

Refer to Page 8 Item # 19 for location of Voltage Selector Switch

10
 OPERATING INSTRUCTION 4. Use extra care in positioning the bead breaker shoe on
larger wheels/tires, and on alloy wheels. Make sure the
The unit must be properly operated and main- shoe rests next to but not on the rim, and not on the tire
tained to help avoid accidents that could damage sidewall.
the unit and injure the operator or bystanders.
This section of the Operating Instructions manual 5. Pull the bead breaker shoe away from the machine and
review basic operations and use of controls. roll the wheel into position. The valve stem should be in the
These instructions should be reviewed with all 2 o’clock position.
employees before they are allowed to work with
the machine. Keep these instructions near the 6. Position the bead breaker shoe against the tire next to,
machine for easy reference. but not on, the rim. Press the breaker pedal to actuate the
shoe and loosen the bead. It may be necessary to loosen
BEAD LOOSENING AND DEMOUNTING the bead in multiple locations around the tire. (See Fig. 2).

This machine may operate differently from

machines you have previously operated.
Practice with a regular steel wheel and tire
combination to familiarize yourself with the
machine’s operation and function.
 Remember to remove all weights from both sides of the
wheel. Weights left on the back side of the wheel may cause
Fig. 2
the wheel to be clamped un-level. This may result in the
combination mount/demount head contacting the rim
causing scratches. On alloy wheels, always rotate the wheel 7. Turn wheel around and repeat procedure on the other
one turn after setting the head to insure proper wheel side of the wheel. This should be the long side of the drop
chucking. center. It will be easier to clamp the wheel to the table top if
the lower bead is loosened last. (See Fig. 3).
 Always review nicks and scratches with owners of
expensive wheel and tire combinations prior to servicing.

 Review the performance wheel section of this manual

prior to servicing performance tire/wheel combinations.

1. Deflate tire completely by removing the valve core from

the valve stem. (See Fig. 1).

Fig. 3

8. Determine the mounting side of the wheel. The mounting

side is the narrow side of the drop center. The tire is
removed for clarity. (See Fig. 4).

Fig. 1 Fig. 4

2. The clamps on the table top may extend beyond the table
top itself. To avoid damaging the clamps and/or wheel,
move the clamps to their full inward position before
positioning a tire for bead loosening.

3. Always loosen the bead on the narrow side of the wheels

drop center first. ( See Fig. 4 for better description of the
drop center.)

11
9. Place tire/wheel assembly on table top with mounting 13. After the wheel is secured to the turntable, pull the over-
side up (See Fig. 1) head swing arm into position so that the mount/demount
head is directly over the edge of the rim. Push down on the
vertical slide until the mount/demount head comes in con-
tact with the edge of the rim. . ( See Fig. 5 )

Fig. 1

10. Use the clamp control pedal to move the clamps inward
(pedal down) or outward (pedal up). (See Fig. 2.)
NOTE Fig. 5
Clamp steel wheels from the inside (clamps
14. Push the vertical slide down and position the demount
push outward against wheel). Clamp mag and
head into contact with the rim edge. (See Fig. 6-7)
custom wheels from the outside (Clamps push
inward against the outside rim edge). Refer to
the Performance Tires and Wheels section. Fig. 6

Fig. 2

Fig. 7

11. Apply tire manufacturer’s approved rubber lubricant

liberally to entire circumference of both beads after loosening
bead and placing on table top. Using the mount/demount
roller to hold down the top bead while rotating the turntable
will make lubrication easier. (See Fig. 3)

15 .Push up on the locking handle to lock the slide into

position. As the slide is locked, the mount/demount head
will move upward approximately 1/8 inch and backward 1/8
inch from the rim edge. The mount/demount head roller
Fig. 3
should not be in contact with the rim edge. (See Fig. 1)
12. Use the lower bead helpers to assist in the bottom bead
lubrication. (See Fig. 4) Fig. 1

Fig. 4

12
 18. Power the left top helper down to force the tire bead into
the drop the center of the wheel. (See Fig. 5-6)

NOTE Fig. 5
This clearance will be maintained as long as the
slide lock remains locked. The operator may swing
the arm out of the way and back into place again
without needing to reposition the head when chang-
ing a like set of wheels. The tool clearance may
change with machine use and should be inspected
often. Failure to maintain proper clearance may
result in damage to the wheel rim or tire.

Fig. 6

Note:
The Following Procedures show
optional equipment being used;
The Tire Changer you are using may not have the
Assist Tower Option.

19. Insert the smooth curved end of tool bar over the right
16. Move the left hand top helper into position opposite the end knob of the mount/demount head and below the top
mount/demount head positioning the edge of the helper just bead of the tire. (See Fig. 7 & 8)
outside the rim edge. (See Fig. 2-3)

Fig. 2 Fig. 7

Fig. 8

Fig. 3
20. Push the tool bar down toward the wheel to lift the tire
bead up and over the right -side knob portion of the demount
17. Press down on the left hand control valve. (See Fig. 4) head. Hold the tool bar in this position.(See Fig. 9-10)

Fig. 9

Fig. 4

13
 Fig. 4

Fig. 10

21. Depress the table top pedal to rotate the wheel clockwise.
Leave the left hand helper in position opposite the demount 23. Insert the smooth curved end of the tool bar over the
head and allow it to follow the wheel rotation to assist the right end of demount head and below the lower bead of the
bead into drop center while demounting. Hold the tool bar tire. Push the tool bar down toward the wheel to lift the tire
down until demounting nears completion. (See Fig. 1-3) bead up and over the right -side knob portion of the demount
head. Hold the tool bar in this position. (See Fig. 5-6)
Fig. 1

Fig. 2 Fig. 5

Fig. 6

24. Depress the table top pedal to rotate the wheel. The
demount head will guide the bead up and over the edge of
the wheel. Continue rotation until the lower bead is
demounted. The helper disks should be removed during
Fig. 3 rotation. Swing them out of the way to complete
demounting. (See Fig. 7)

The tool bar and demount head may encounter

resistance or come under load at times during
the mount and demount procedures. Keep one
hand firmly on the tool to avoid possible tool
kick back. Use the reversing feature ( lift table
top pedal upwards ) to back out of jam ups.

22. Lift and hold the tire so it is positioned with the lower Fig. 7
bead in the drop-center portion of the wheel. If the tire is
large/wide or has become stuck on the lower part of the rim,
the lower bead helper disk may be used to unstick and raise
the tire. (See Fig. 4)
14
 CUSTOM AND SPECIAL WHEELS 3. After upper bead is demounted, remove tube and
demount lower bead.
If a custom wheel is damaged in dismounting, STOP, and
NOTE
avoid damaging the other wheels. Continue only when the
Table top rotation can be stopped at any time by
cause is identified and corrected.
removing your foot from the rotation pedal.
Normal table top rotation for demounting is
clockwise. Depress the table top pedal to rotate
this direction. To rotate the table top counter-
clockwise, lift the pedal up with your toe.

Alloy Wheels
Some manufacturers offer wheels with little or no drop FOR TUBE-TYPE TIRES
center. These are not DOT approved. The tire or wheel - or With tube-type tires, demount the upper bead
both - can be damaged and the tire could explode under and remove the tube before de-mounting the
pressure, resulting in serious injury or death. If you attempt lower bead.
to mount/demount this type of wheel, use extreme caution.
MOUNTING
This information must be read and followed carefully to
prevent accidents and injuries during mounting.

Check tire and wheel carefully before mounting.

European Performance Wheels (Asymmetrical Hump) Make sure the tire bead diameter and wheel
Some European wheels have very large humps except near diameter match exactly. Consult the Rubber
the valve hole. On these wheels, the beads should be Manufacturer's Association for approved rim
loosened at the valve hole on both the upper and lower widths for tire sizes.
sides first.

Wheels with Low Pressure Warning Sensors

Performance wheels on some vehicles (including Corvette,
BMW, Lamborghini Diablo) have a pressure sensor
strapped to the rim opposite the valve hole. On these Attempts to force a bead seat on mis-matched
wheels, the beads should be loosened at the valve hole on tires and wheels can cause the tire to violently
both upper and lower sides first. explode, causing serious personal injury or
death to operator and/or bystanders.

Never mount a tire and wheel handed to you by

anyone without checking both tire and wheel for
DEMOUNTING TUBE TYPE TIRES damage and compatibility. Be extra cautious of
persons without knowledge of tire service. Keep
1. After both tire beads are loosened, lubricate the beads bystanders out of service area.
and rim liberally.

2. Position the demount head and bead lifting tool as

described earlier paying careful attention not to pinch the
tube. Depress the table top pedal and rotate only a short
distance at a time. This allows you to stop the process Never mount a damaged tire. Never mount a tire
should you suspect the tube is getting pinched. on a rusty or damaged wheel. Damaged tires
and/or wheels may explode.

15
 5. Manually force the tire down into the drop center of the
wheel directly across from the mount head to reduce the
tensional force on the bead. Depress the table top pedal and
rotate the wheel to mount the lower bead. Rotate the table top
If you damage the tire bead during mounting,
until the lower bead is fully mounted. ( See Fig. 5-6)
STOP!, remove the tire and mark it as damaged.
Do not mount a damaged tire.
1. Inspect the wheel closely for damage. Clean the wheel
and remove any light corrosion or rubber residue. Do not
attempt to service heavily corroded wheels. ( See Fig. 1)

Fig. 5

Fig. 1

2. Inspect tire for damage, paying close attention to the

beads. Verify size match between tire and wheel.
( See Fig. 2) Fig. 6

Fig. 2 6. For the top bead, rotate the table top until the valve stem
is directly across from the mount head. Lift the upper bead
above the left “duckbill” side of the mount/demount head
and below the right front knob. ( See Fig. 7-8)

Fig. 7

3. Lubricate both tire beads liberally with tire manufacturer

approved lubricant. ( See Fig. 3)
Fig. 3

Fig. 8

4. Place tire over wheel and move tower and

mount/demount head into position as described earlier.
Position tire so that the lower bead is above the left
“duckbill” side of the mount/demount head and below the
right front knob. ( See Fig. 4)
Fig. 4 Note:
The Following Procedures show
optional equipment being used;
The Tire Changer you are using may
not have the Assist Tower Option.

16
8. With the left side helper, press down on the tire near the MOUNTING TUBE TYPE TIRES
right side assist roller to hold the tire in the drop center.
( See Fig. 1) 1. Lubricate the beads and rim liberally.

Fig. 1 2. Position the demount head and bead lifting tool as

described earlier. Mount the bottom bead first.

3. Round out the tube with a small amount of air. Avoid

pinching or forcing the tube. Apply rubber lubricant to the
tube.

4. Insert the tube into the tire paying careful attention not to
9. Depress the table top pedal and rotate the tire until the pinch the tube.
bead is mounted. The left side helper shoe will follow the tire
during rotation. ( See Fig. 2-5) 5. Depress the table top pedal and rotate only a short
distance at a time. This allows you to stop the process
should you suspect the tube is getting pinched.

6. Mount the top bead.

Do not force the tire onto the rim. Bead damage

Fig. 2 could result making the tire unsafe and/or
creating the risk of injury.

Fig. 3 INFLATION INSTRUCTIONS

Tire inflation is performed in four steps: Restraint, Bead
Seal, Bead Seat, and Inflation. Read the explanation of
each step and understand them thoroughly before
proceeding.

Check inflation gauge for proper operation .

Accurate pressure readings are important to safe
tire inflation. Refer to the Operating Maintenance
section of this manual for instructions. If the rim
has been clamped from the outside for tire
mounting, release the clamps once bead seal is
obtained, lift the tire, and move the clamps to the
center of the table top.

Fig. 4

Tire failure under pressure is hazardous. This tire

changer is not intended to be a safety device to
contain exploding tires, tubes, wheels, or bead
sealing equipment. Inspect tire and wheel carefully
for match, wear, or defects before mounting.
Always use approved tire bead lubricant during
mounting and inflation. The inflation pedal, located
Fig. 5 at the center of the left side of the machine,
controls the flow of air through the inflation hose.
17
 The clip-on air chuck on the end of the inflation
hose and all inflation related components should
be checked weekly for proper operation. DO NOT
USE this machine for tire inflation if any parts are
damaged or appear not in proper working order. Fig. 3

INFLATION PEDAL OPERATION

The three-position inflation pedal located at the center of the Position Three - Bead Sealing – This is the second ( pressed
left side of the machine serves three different functions. It all the way down ) activated position. With the inflation hose
checks air pressure in the tire; controls the flow of air attached to the tire valve and the pedal in this position, line
through the inflation hose; and operates the “Jet-Blast” bead pressure is allowed to flow through the valve and to the “Jet-
sealing nozzles . ( See Fig. 1 ) Blast” nozzles on the table top for bead sealing. ( See Fig. 4 )

Fig. 4

Fig. 1

Do not use the “Jet-Blast” bead sealing nozzles

without a tire and wheel positioned on the table
top. Dirt and debris could be blown into the air with
enough force to injure the operator or bystanders.
Do not use this position to inflate a tire.

Position One - Tire Pressure – With the inflation hose

attached to the tire valve and the pedal in this position, the TIRE INFLATION
air gauge will register the air pressure in the tire. Whenever
your foot is removed from the pedal, it will return to this The unit is equipped with a pressure limiter/regulator to
position. ( See Fig. 2 ) assist the operator with proper tire inflation. The pressure
limiter will keep most car and light truck tires from inflating
beyond 60 PSI (smaller tires may reach higher pressures).
Fig. 2 It is the operators responsibility to follow all instructions and
to control inflation pressure as specified in these
instructions. (See Fig. 5)

Position Two - Tire Inflation – This is the first activated posi-

tion. With the inflation hose attached to the tire valve and the
pedal in this position, line pressure is allowed to flow through
the valve and into the tire for inflation. Tire pressure is not Fig. 5
indicated on the gauge in this position. ( See Fig. 3 )
18
 Check the function of the pressure limiter
regularly and maintain it according to the
instructions provided in this manual for safe and
proper operation. Do not tamper with or attempt
to adjust the pressure limiter. Tires requiring
Fig. 3
inflation beyond 60 PSI should only be inflated in
a safety cage.

STAGES OF INFLATION
Hold the restraint tool firmly in place when
Review the following descriptions and diagrams carefully. installing and/or removing from the left helper
Refer to them as necessary during wheel restraint, bead assembly. The unit can drop suddenly to the floor.
sealing, bead seating, and inflation to verify that you are Be sure to keep feet clear at all times.
proceeding properly and safely.
STAGE TWO / BEAD SEALING
STAGE ONE / WHEEL RESTRAINT 1. Position valve stem in front of operator and connect the
As an added safety precaution, a wheel restraint devise has inflation hose. (See Fig. 4)
been added to protect operators during tire inflation.
Fig. 4

This devise is a restraint devise only. It will not

protect operators in the event of catastrophic
tire/wheel rupture or failure. Always use extreme
caution during the inflation procedure. As an added
safety precaution, safety cages that conform to
OSHA standard 1910.177 are recommended. 2. Hold tire up against upper edge of the wheel. Be sure tires
top bead is over the bottom of the valve stem. (See Fig. 5)
1. Raise the left helper and support assembly and insert the
restraint devise as shown. (See Fig. 1)
Fig. 5

Fig. 1 3. Depress inflation pedal to position two and hold about one
second to begin air flow through tire valve, then depress pedal
2. Make sure the restraint tool is centered in the center hub to position three and hold briefly – less than 1 full second. The
of the wheel then press down on the left hand control valve. blast of air from the jets will expand tire and seal the beads.
(See Fig. 2-3) (See Fig. 6-7)

Fig. 2 Fig. 6
19
 Fig. 1

Fig. 7

4 .
Release the inflation pedal and allow it to return to posi-
tion one. Verify that both beads are completely sealed to the 2. Release air pressure from the tire by pressing the manual
wheel. Repeat these steps if beads have not sealed. It may release valve button. NOTE: The inflation hose must be
be necessary to wait a few seconds for the air storage tank attached to the valve stem during this procedure. (See Fig. 2)
to recover before attempting again. If tire and wheel are
properly lubricated and operator cannot achieve bead seal
Fig. 2
after a few attempts, the valve core may be removed from
the valve stem to allow more air flow into the tire to assist
with bead seal. After bead seal is achieved, remove the
chuck and reinstall the valve core.

STAGE THREE / BEAD SEATING

Bead seating usually occurs on the long tapered side of the
wheel first and the shorter side last. Bead seating will
usually require at least 7 PSI in the tire. 40 PSI is the
maximum safe pressure at this stage regardless of tire
operating pressure. Most European import cars and many
aftermarket alloy wheels are very tight and can be difficult to
Check tire pressure frequently. Never exceed 40
bead seat. Also note that asymmetrical hump and run-flat
PSI while seating beads. Once seated, never
tires are extremely difficult to bead seat. Follow tire
exceed tire manufacturer's recommended air
manufacturer's recommended procedure for bead seating.
pressure. Tires can explode, especially if they
are inflated beyond their limits. At all pressure
levels when inflating through the valve stem,
keep hands, arms, and entire body away from
inflating tire. An exploding tire, wheel, or bead
Operator should keep hands, arms, and entire
sealing equipment may propel upward and
body away from the tire during the remaining
outward with sufficient force to cause serious
bead seat and inflation procedures. Do not
injury or death to operator or bystander.
stand over tire, as personal injury could result.
from inflating tire. Avoid distraction during
inflation. Check tire pressure frequently to avoid MIS-MATCHED TIRES AND WHEELS
over inflation. Excessive pressure can cause Never attempt to mount and inflate mis-matched
tires to explode, causing serious injury or death tires and wheels. Mis-matched tire and wheel
to operator or bystander. combinations can explode, causing personal
injury or death to operator and bystanders. For
1. Once tire pressure is indicated on the air gauge (inflation safety, do not attempt to mount and inflate
pedal in position one; foot removed from pedal), continue to mis-matched tires and wheels.
inject air into the tire in short intervals. Check the pressure
frequently. Stand back during bead seat. Keep hands, arms,
and entire body away from tire during this procedure. Tire
beads should move outward and "pop" into their bead seat
position as pressure inside the tire increases. If this does not
happen, a problem exists. Investigate carefully. (See Fig. 1) NEVER increase air pressure to exceed 40 PSI
when attempting Bead Seat. If operator is
unable to obtain Bead Seat, something is wrong.
Deflate tire completely, inspect tire and wheel,
correct any problems found, relubricate both tire
beads, and reattempt Bead Seal and Seat
KEEP HANDS AND FINGERS CLEAR.
procedures. Follow all safety instructions in this
Keep entire body away from the tire
manual and on machine.
20
 STAGE FOUR / TIRE INFLATION
1. Make sure both beads are seated. When both beads are
seated, the tire is ready for inflation.

2. Replace the valve core if it was removed.

3. Depress the inflation pedal to position two to inflate the

tire. DO NOT STAND OVER TIRE DURING INFLATION.

4. Do not inflate the tire above the manufacturer's

recommended pressure as stamped on the tire sidewall.
The typical inflation pressure for automobile tires is between
24 and 45 PSI. Light truck inflation pressure typically covers
a wider range. Release air pressure from the tire by
pressing the manual release valve button.
MAINTENANCE INSTRUCTIONS
Read and follow all the maintenance instructions provided in
this manual to keep the machine in good operating
condition. Regular inspections and proper maintenance are
THE INFLATION PRESSURE LIMITER IS PRE-SET essential to preventing accidents and injuries. These
AT THE FACTORY AND SHOULD NEED NO instructions will help you service the unit. Instructions are for
ADJUSTMENT. ADJUST ONLY IF PRESSURE
a person with some mechanical ability and training. No
EXCEEDS 60 PSI. Operating a tire changer with a
defective, improperly adjusted, or by-passed attempt has been made to describe all basic steps like how
pressure limiter could result in a tire explosion with to loosen or tighten fasteners. Basic procedures such as
severe injury or death to the operator or cycling systems and checking operation of the equipment
bystanders. Always be sure that the pressure are not fully described since they are described in this
limiter is operating properly on the machine at all manual. Do not attempt to perform work beyond your ability
times. Pressure limiter is set at 60 PSI. Any or at which you have no experience. If you need assistance,
required inflation above 60 PSI should be call an authorized service center or contact the factory.
performed in an inflation chamber/safety cage.
A tire explosion may cause personal injury or
death to operator or bystanders.

 Before making any inspection, adjustment, or

repair, disconnect the power source and block
out all moving parts to prevent injury.

 Keep the machine and the immediate work

area clean. Do not use compressed air to remove
dirt and debris from the machine. Foreign
material may be propelled into the air and into
operator or bystander causing personal injury.

 Wear protective clothing and use eye

protection when making any adjustments or
repairs to the machine.

DAILY
 Check the tire pressure gauge function daily, and check
the accuracy monthly. Use a pressurized tire and a high
quality stick-type pressure gauge. If necessary, adjust the
dial of the machine gauge. If the gauge is defective, replace
it immediately.
IMPORTANT
When inflating tires that require more than 60  Make sure all fasteners are securely tightened and all
PSI, always use a safety cage and air hose with guards and covers are in place.
a clip-on air chuck and in-line valve. The hose
must have enough length between the chuck  Check for worn, damaged or missing parts including
and the operation/in-line valve to allow the grips and protective covers. Replace them before allowing
operator to stand outside the trajectory. the unit to be used.

21
 MONTHLY Mount/Demount Tool Head Adjustment
 Lubricate the arm Pivot Pin. If so equipped, the vertical To adjust tool head lift, adjust locking nut up or down until lift
slides should be cleaned with a vaporizing solvent and then clearance is 1/8" to 3/16". Recheck clearance before
lubricated with chassis grease once a month. replacing cover. (See Fig. 3)
(See Fig. 1-2)

Fig. 1

Fig. 3

Mount/Demount Head Cleaning

Clean dirt and debris from the mount/demount tool roller
with small screw driver or pick. (See Fig. 4)

Fig. 4

Fig. 2

Water Separator/Lubricator Maintenance

Check oil and water levels regularly, and perform these
maintenance items weekly:

 Disconnect air supply to machine. (See Fig. 5)

Fig. 5

 Check adjustment of the mount/demount head monthly.

 Check function of the inflation hose pressure limiter/

regulator monthly. Always secure/stow the cover if
adjustments are made. The pressure regulator should
never be adjusted to exceed 60 PSI.

 The table top, clamps, steel mount/demount head, and

other working surfaces should be cleaned with a vaporizing
solvent every month.
 Observe the sight glass on the water separator/filter
 On a daily basis, inspect the unit and check to be unit. If water is observed, drain by pressing upwards on the
certain that all systems are operating normally. Follow drain plug at the bottom of the reservoir. (See Fig. 6)
detailed inspection and testing procedures as specified for
various components at regular intervals.  Add oil to the lubricator if the fluid level is below the
middle of the sight glass. Remove the reservoir by turning
 Replace any damaged or missing safety decal's. They counter-clockwise and pulling down. Add SAE 10W non-
are available from the factory. detergent oil or an air tool oil if necessary.
22
 Fig. 2
Fig. 6

3. Depress inflation pedal to position one to start air flow

through the hose and into the tank. Maintain a steady
pressure for constant flow.
Reconnect the air when service/adjustments are complete.
4. Watch the rising pressure on the tank gauge and the
gauge on the machine. Machine gauge should cycle
between check and inflation pressures while tank gauge
Inflation Pedal Pressure Limiter Maintenance climbs steadily. As tank pressure reaches 60 PSI, the
The inflation pedal pressure limiter helps prevent inflation of pressure limiter should stop the air flow automatically. Both
standard size or larger tires or tubes beyond 60 PSI to gauges should read 60 PSI ± 5 PSI.
minimize risk of explosion. This device is for the safety of
the operator and bystanders. Proper operation of the pres- 5. If the pressure exceeds 60 PSI, adjust the knob on the
sure limiter is essential to safe operation of the machine. regulator by lifting the locking cover and turning
(See Fig. 1) COUNTERCLOCKWISE. After adjustment is made, secure
cover in the locked position.

6. Repeat steps 1-6. Re-adjust if necessary.

7. After pressure limit has been set, check the manual

release valve function by pressing the button and releasing
pressure from the tank until it reaches 50 PSI. Disconnect
inflation hose, and release air inside tank. (See Fig. 4)
Fig. 1
Fig. 4

THE PRESSURE LIMITER IS PRE-SET AT THE

FACTORY AND SHOULD NEED NO ADJUSTMENT.
ADJUST ONLY IF PRESSURE EXCEEDS 60 PSI.
Operating a tire changer with a defective,
improperly adjusted, or by-passed pressure limiter INSTALLATION INSTRUCTIONS
could result in a tire explosion with severe injury or
death to the operator or bystanders. Always be Location
sure that the pressure limiter is operating properly Select a location using the drawings on page 23. The area
on the machine at all times. Pressure limiter is set should provide the operator with enough space to use the
at 60 PSI. Any required inflation above 60 PSI equipment in a safe manner. The area selected should be
should be performed in an inflation chamber/safety well lit, easy to clean and should be away from oil, grease,
cage. A tire explosion may cause personal injury or
brake lathe chips, etc. Avoid areas where bystanders and
death to operator or bystanders.
customers may be present.
Check operation of the pressure limiter as follows at least
once a month:

1. Remove tires and/or wheels from the machine.

Proper unit installation is necessary for safe use
2. Connect the inflation hose to an empty service tank with and efficient operation. Proper installation also
a pressure gauge (gauge should read 0). Use a certified helps protect the unit from damage and makes
tank with at least 250 PSI pressure rating. (See Fig. 2) service easier. Always keep this manual unit.
23
24
 RECORD ALL MAINTENANCE NOTES
AND SERVICE HISTORY HERE
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________

25
 RX-950/950AT BODY
RX850/950 SPARE PARTS-
BODY
Page 1 of 8

26
 RX-950/950AT BODY
# Part # Name Specification Quantity BPK Description
101 5401101 Body GT890.01.00 1 Body RX-950
101 5401125 Body Body RX-850
102 5401102 Rubber Washer 52 X 42 X 23 4 Rubber Mounting Block
103 5400110 Lever 20" 1 Pry Bar
104 5401104 Wheel Support 395 X 125 X 23 1 Lg Wheel Support Pad
105 5400914 Flat Washer 6 13 #6 Washer
106 5400958 Screw M6 X 16 13 M6X16 Bolt
107 5401107 Grease Container Holder 1 Soap Bucket Retaining Ring
108 5401108 Grease Container 1 Soap Bucket
109 5400121 Soap Brush
110 5401110 Grease Container Cover 1 Soap Bucket Cover
111 5400912 Flat Washer 5 2 #5 Washer
112 5400951 Screw M5 X 16 1 M5X16 Bolt
113 5400936 PU Hose 8X5 some 8X5 Air Hose
114 5400931 Union G 1/4" 8 1 8MM 1/4" 90* Fitting
115 5400931 Union G 1/4" 8 2 8MM 1/4" 90* Fitting
116 5401116 Air Regulator 0.1-1.0Mpa 1 Air/Oil Regulator
117 5401117 Pressure Gauge 0.1-1.0Mpa G 1/8" 1 Gauge / Air-Oil Regulator
118 5401118 Screw M5 X 12 2 M5X12 Bolt
119 5400916 Union G 1/4" 1 1/4" Straight Fitting
120 5400932 Union 3-G 1/4" 1 8MM 1/4" Tee Fitting
121 5401121 Power Cable 1 Power Cord
103 5400110 Lever 20" 1 Pry Bar
104 5401104 Wheel Support 395 X 125 X 23 1 Lg Wheel Support Pad
105 5400914 Flat Washer 6 13 #6 Washer
106 5400958 Screw M6 X 16 13 M6X16 Bolt
107 5401107 Grease Container Holder 1 Soap Bucket Retaining Ring
108 5401108 Grease Container 1 Soap Bucket
109 5400121 Soap Brush
110 5401110 Grease Container Cover 1 Soap Bucket Cover
111 5400912 Flat Washer 5 2 #5 Washer
112 5400951 Screw M5 X 16 1 M5X16 Bolt
113 5400936 PU Hose 8X5 some 8X5 Air Hose
114 5400931 Union G 1/4" 8 1 8MM 1/4" 90* Fitting
115 5400931 Union G 1/4" 8 2 8MM 1/4" 90* Fitting
116 5401116 Air Regulator 0.1-1.0Mpa 1 Air/Oil Regulator
117 5401117 Pressure Gauge 0.1-1.0Mpa G 1/8" 1 Gauge / Air-Oil Regulator
118 5401118 Screw M5 X 12 2 M5X12 Bolt
119 5400916 Union G 1/4" 1 1/4" Straight Fitting
120 5400932 Union 3-G 1/4" 1 8MM 1/4" Tee Fitting
121 5401121 Power Cable 1 Power Cord
122 5401122 Tool Support 11 Plastic Tool Tray
123 5400931 Union G 1/4" 8 1 8MM 1/4" Straight Fitting
124 5400961 Nut M8 3 M8 Nut
125 5400915 Elastic Washer 8 3 #8 Plastic Washer
126 5400901 Flat Washer 8 6 #8 Washer
127 5400962 Screw M8 X 20 3 M8X20 Bolt
128 5400906 Flat Washer 12 1 #12 Washer
27
 RX-950/950AT VERTICAL ARM
RX850/950 SPARE PARTS-VERTICAL ARM
Page 2 of 8

28
 RX-950/950AT VERTICAL ARM
# Part # Name Specification QTY BPK Description
201 5400201 Mounting Head 1 Demount Head
202 5400202 Roller GT890.03.12 1 Demount Head Roller
203 5400203 Pin GT890.03.13 1 Demount Head Roller Pin
204 5400943 Screw M10 X 25 1 M10X25 Demount Head Bolt
205 5400205 Pressing Washer GT890.03.11 1 34X 1 X 8 Demount Head Washer
206 5401206 Pin M10 X16 2 M10X16 Set Screw
207 5401207 Shock Absorber GT890.03.10 1 S36 Rubber Shock Absorber
208 5401208 Mounting Bar GT890.03.05 1 S36 X 710 Hex Shaft RX-850
209 5401209 Handle Cover GT890.03.14 1 Handle GripHex Shaft Locking Bar
210 5401210 Locking Handle GT890.03.15.00 1 Lock Handle
211 5401211 Seeger Ring #24 1 #24 Snap Ring
212 5401212 Spring GT890.03.06 1 43X 3 X 63 Hex Shaft Locking Plate Spring
213 5401213 Locking Plate GT890.03.07 1 Hex Shaft Locking Plate
214 5400457 Locknut M10 2 M10 Nylock Nut
215 5400903 Flat Washer 10 2 #10 Washer
216 5400937 Nut M10 1 M10 Nut
217 5401217 Screw M10 X 70 1 Locking Plate Adjusting Screw
218 5401218 Spring GT890.03.04 1 43 X 3 X 520 Hex Shaft Spring RX-950
218 Spring GT850.03.03 1 43 X 3 X 430 Hex Shaft Spring RX-850
219 5401219 Knob GT890.03.03 1 Hex Shaft Cap / RX-850, RX-950
220 5401220 Screw 1 M8 X 30 Hex Shaft Cap Screw
221 5401221 Horizontal Arm GT890.03.02.00 1 Upper Swing Arm Assembly/ RX-950
237 5401237 Spring T-K.03.02.03 1 7.5 X .8 X 16 Tire Deflator Valve Spring
238 5401238 Valve Body T-K03.02.01 1 Tire Deflator Valve Body
239 5401239 O-Ring 7 X 1.9 1 Tire Deflator Valve O-Ring
240 5401240 Valve T-K.03.03 1 Tire Deflator Valve Block
241 5401241 Screw M4 X 12 3 M4X12 Bolt
242 5401242 Pressure Gauge 0.1-1.0Mpa M14 X 1.5 1 Pressure Gauge
243 5400910 Flat Washer 4 3 #4 Washer
244 5400909 Elastic Washer 4 3 #4 Plastic Washer
245 5400970 Nut M4 3 M4 Nut
246 5400971 Union T-K.03.04 1 Pressure Gauge Nut
247 5400931 Union G1/4" 8 1 8MM 1/4" 90* Fitting
248 5401248 Gauge Cover T-K.03.01 1 Tire Inflator Housing
249 5400957 Screw M6 X 10 2 M6X10 Bolt
250 5400914 Flat Washer GT890.03.08 2 6 #6 Washer
251 5401251 Horizontal Arm Cover GT890.03.05 1 Horizontal Arm Cover RX-950
251 Horizontal Arm Cover GT850.03.05 1 Horizontal Arm Cover RX-850
252 5401252 Pin M10 X 12 2 Demount Head Set Screw
253 5400207 Cover 1 Demount Head Roller Cover
254 5401254 Plastic Cover 1 Guard Cover Vertical Insert
255 5401255 Union GT890.02.10 1 Air Fitting / Main Tank
256 5401256 Locknut GT890.02.11 1 Main Tank Air Fitting Locknut
257 5400923 Union G1/4" 12 2 12MM 1/4" Straight Fitting
258 5400916 Union 2-G1/4" 1 1/4" Straight Fitting
259 5401259 Safety Valve 0.1-15Mpa G1/4" 1 Pressure Release Valve
260 5400917 Union 3-G1/4" 1 1/4" Tee Fitting
261 5401261 Gauge 0.1-1.0Mpa G1/8" 1 Gauge / PSI / Reservoir RX-850/950
29
 RX-950/950AT PEDAL UNIT
UNIVERSAL PARTS-PEDAL UNIT
T-D .02.00
3-A
Page 3 of 6

30
 RX-950/950AT PEDAL UNIT
# Part # Name Specification Quantity BPK Description
301 5400301 Pedal T-D. 02. 12 3 Foot Pedal
302 5400302 Spacer Pedal T-D. 02. 01 1 Front Foot Pedal Shaft Spacer
303 5400964 Screw M8 X 50 1 M8X50 Bolt
304 5400304 Spring T-D. 02. 02 1 Turntable Foot Pedal Return Spring
305 5400972 Seeger Ring #14 2 #14 Snap Ring
306 5400961 Nut M8 2 M8 Nut
307 5400307 Spacer T-D. 02. 25 2 Sliding Bracket Spacer
308 5400308 Reverse Connecting Rod T-D. 02. 22 1 Plastic Cam Link
309 5400981 Locknut M8 3 M8 Nylock Nut
310 5400914 Flat Washer 6 8 #6 Washer
311 5400956 Nut M6 10 M6 Nut
312 5400312 Bracket T-D. 02. 21 1 Foot Pedal Return Spring Brkt
313 5400313 Spindle T-D. 02. 26 1 Plastic Cam Link Bolt
314 5400958 Screw M6 X 16 5 M6X16 Bolt
315 5400913 Plastic Washer 6 8 #6 Plastic Washer
316 5401316 Pedal Bracket T-D. 02. 03 1 Foot Pedal Bracket
317 5400959 Screw M6 X 30 1 M6X30 Bolt
318 5400318 Bracket T-D. 02. 15 2 Air Valve Linkage Bracket
319 5400319 Spring T-D. 02. 04 2 BB Foot Pedal Return Spring
320 5400320 Connecting Rod T-D. 02. 11 1 Plastic Cam Link
321 5400981 Locknut M8 2 M8 Nylock Nut
322 5400322 Spacer T-D. 02. 10 1 Spacer
327 5400958 Screw M5 X 16 4 M6X16 Bolt
330 5400330 Switch Bracket T-D. 02. 17A 1 Switch Mounting Bracket
331 5400331 Reverse Switch 40A 1 Turntable Direction Switch
332 5400332 Reverse Switch Guide 1 Switch Cover
333 5400936 PU Hose 8X5 8X5 Air Hose
334 5400334 Valve Assy 1 BB Foot Pedal Air Valve
334.1 5400903 Flat Washer 10 1 #10 Washer
334.2 5400342 Valve Body T-D. 02. 14 1 Valve Body
334.3 5400935 Union G1 / 8" - 8 1 8MM 1/8" Tee Fitting
334.4 5400934 Union G1 / 8" - 8 2 8MM 1/8" Straight Fitting
334.5 5400343 Distance Ring 15 Air Valve Spacer
334.6 5400344 O-ring 17 X 4 18 17X4 O-Ring
334.7 5400345 Tack 4 X 20 1 4X20 Pin
334.8 5400346 Valve Pin T-D. 02. 13A 1 Air Valve Shaft
335 5400335 Cam Bracket T-D. 02. 02 1 Cam Bracket
336 5400336 Cam T-D. 02. 24 1 Plastic Cam
337 5400959 Screw M6 X 20 2 M6X20 Bolt
338 5400338 Fork Plate Spring 1 Fork & Leaf Spring
339 5400958 Screw M6 X 16 1 M6X16 Bolt
340 5401340 Valve Assy 1 Air Valve / Open & Close Clamps RX-850 / 950
340.1 5400347 Silencer G1 / 8" 4 Silencer
340.2 5400933 Union G1 / 8" -8 1 8MM 1/8" 90* Fitting
340.3 5400342 Valve Body T-D. 02. 14 1 Valve Body
340.4 5400346 Valve Pin T-D. 02. 07 1 Air Valve Shaft
340.5 5400929 Union G1 / 8" -6 2 6MM 1/8" Straight Fitting
341 5401341 Spindle T-D.02.20 1 Foot Pedal Shaft
31
 RX-950/950AT
UNIVERSAL TURNTABLE
SPARE PARTS-TURNTABLE
T-20YK.00.00 Page 4 of 8

32
 RX-950/950AT TURNTABLE
# Part # Name Specification Quantity BPK Description
401 5401401 Turntable T-20YK.00.01 Turntable
401 5401448 Turntable T-20YK.00.01 1 M12 X 25 Turntable
402 5401402 Screw 1 M12X25 Bolt
403 5401403 Turntable Cap T-18Y.00.02 1 Turntable Bushing
404 5401404 Disk Key 10 X 50 1 Gearbox Shaft Key
405 5401405 Clamp T-18Y.00.03 4 Jaw Clamp
406 5401406 Slide T-18YK.00.02.00 4 Jaw Clamp Support
407 5400921 Union G1/8 10 4 10MM 1/8" Straight Fitting
408 5400922 PU Hose 10 some 10MM Air Hose
409 5401409 Slide Plate T-20YK.00.04 2 Slide Block
410 5400906 Flat Washer 12 16 #12 Washer
411 5400904 Elastic Washer 12 8 #12 Plastic Washer
412 5401412 Screw M12 X 30 4 M12X35 Bolt
413 5401413 Washer T-18Y.00.08 4 Bushing
414 5401414 Connecting Plate T-20YK.00.03.00 4 Jaw Clamp Linkage
415 5401415 Screw M12 X 83 4 M12X83 Bolt
416 5401416 Seeger Ring #65 1 #65 Snap Ring
417 5400905 Seeger Ring #12 4 #12 Snap Ring
418 5401418 Cylinder Bracket T-20YK.00.02.00 2 Jaw Clamp Support Bracket
419 5401419 Rear Housing of Cylinder T-18X.00.05 2 Clamp Cylinder Rear Cover
420 5401420 Cylinder Body T-20X.00.02 2 Clamp Cylinder Body
421 5401421 Union T-20X.00.03 8 M8 Clamp Cylinder Connecting Bolt
422 5401422 Front Housing for Cylinder T-18X.00.02 2 Cylinder Cover Shaft Side
423 5400981 Locknut M8 8 M8 Nut
424 5401424 Shaft for Cylinder T-20X.00.01 2 Clamp Cylinder Shaft
425 5401425 Union 6 2 Banjo Bolt 6MM Double
426 5400977 PU Hose 6X4 some 6mm Air Hose
427 5401427 Union 6 2 Banjo Bolt 6MM Single
429 5400929 Union G1/8 6 2 6MM 1/8" Straight Fitting
430 5400920 Union G1/4 10 4 10MM 1/4" Straight Fitting
431 5401431 Rotate Union (inside) T-J.00.02A 1 Rotary Joint Block Top
432 5400922 PU Hose 10 some 10MM Air Hose
433 5400967 Screw M3 X 10 4 M3X10 Bolt
434 5401434 Screw M6 X 25 2 M6X25 Bolt
435 5401435 O-ring 60 X 2.65 3 60X2.65 O-Ring
436 5401436 O-ring 90 X 2.65 1 90X2.65 O-Ring
437 5400926 PU Hose 12 some 12MM Air Hose
438 5400925 Union G3/8 12 2 12MM 3/8" Straight Fitting
439 5401439 Rotate Union (outside) T-J.00.03A 1 Rotary Joint Block Bottom
440 5400929 Union G1/8 6 2 6MM 1/8" Straight Fitting
441 5400930 PU Hose 6X4 some 6mm Air Hose
442 5401442 Clamp Cylinder / RX-950
442 5401443 Cylinder Assembly T-20X.00.00 2 Clamp Cylinder / RX-850
442.1 5401444 O-ring 25 X 3.1 2 25X3.1 O-Ring
442.2 5401445 Y-ring 30 X 18.5 X 5 2 30X18.5X5 Bushing
442.3 5401446 O-ring 70 X 2.65 4 70X2.65 O-Ring
442.4 5401447 Piston 70 X 22 X 11.7 2 70X22X11.7 Piston
442.5 5400946 Locknut M12 2 M12 Nut
33
 RX-950/950AT BEAD BREAKER
UNIVERSAL SPARE PARTS- BEAD BREAKER
T-B.02.00
T-LS.02.00A Page 5 of 6

34
 RX-950/950AT BEAD BREAKER

# Part # Name Specification Qty. BPK Description

501 5401501 Bead Breaker Shoe T-C.02.00 1 Bead Breaker Swing Arm Blade
502 5401502 Handle Cover GT890.03.14 1 Bead Breaker Handle Grip
503 5401503 Bead Breaker T-B.02.00 1 Bead Breaker Swing Arm Assembly RX-950
504 5401504 Washer 80 X 20 X 20 1 80X20X20 Washer
505 5400907 Washer 14 1 #14 Washer
506 5400947 Locknut M14 1 M14 Nylock Nut
507 5400980 Locknut M16 1 M16 Nylock Nut
508 5400908 Flat Washer 16 2 #16 Washer
509 5401509 Screw M6 X 100 1 M6X100 Screw
510 5401510 Spring T-B.02.07 1 13 X 2.5 X 90 Bead Breaker Swing Arm Return Spring
511 5401511 Locknut M8 X 1.5 1 Nylock Nut BB Cylinder Shaft
512 5401512 Cylinder Shaft T-LS.01.01A 1 445 MM Bead Breaker Cylinder Shaft RX-950
513 5400504 Seeger Ring 30# 1 #30 Snap Ring
514 5401514 Adjusting Washer T-LS.01.05A 1 Adjusting Washer
515 5401515 Y-Ring 30 X 20 X 7 1 30 X 20 X 7 Bushing
516 5401516 Guide for Piston 85 (Length) X 10 X 2 1 85 X 10 X 2 Spacer
517 5400933 Union G 1/4 X 8 2 8MM 1/8" 90* Fitting
518 5401434 Screw M6 X 25 12 M6X25 Bolt
519 5400914 Flat Washer 6 12 #6 Washer
520 5401520 Cylinder Housing T-LS.01.04A 1 Bead Breaker Cylinder Cover
506 5400947 Locknut M14 1 M14 Nylock Nut
507 5400980 Locknut M16 1 M16 Nylock Nut
508 5400908 Flat Washer 16 2 #16 Washer
509 5401509 Screw M6 X 100 1 M6X100 Screw
510 5401510 Spring T-B.02.07 1 13 X 2.5 X 90 Bead Breaker Swing Arm Return Spring
511 5401511 Locknut M8 X 1.5 1 Nylock Nut BB Cylinder Shaft
512 5401512 Cylinder Shaft T-LS.01.01A 1 445 MM Bead Breaker Cylinder Shaft RX-950
513 5400504 Seeger Ring 30# 1 #30 Snap Ring
514 5401514 Adjusting Washer T-LS.01.05A 1 Adjusting Washer
515 5401515 Y-Ring 30 X 20 X 7 1 30 X 20 X 7 Bushing
516 5401516 Guide for Piston 85 (Length) X 10 X 2 1 85 X 10 X 2 Spacer
517 5400933 Union G 1/4 X 8 2 8MM 1/8" 90* Fitting
518 5401434 Screw M6 X 25 12 M6X25 Bolt
519 5400914 Flat Washer 6 12 #6 Washer
520 5401520 Cylinder Housing T-LS.01.04A 1 Bead Breaker Cylinder Cover
521 5400512 Screw M4 X 42 2 M4X42 Mounting Screw
522 5400970 Nut M4-S19 2 M4 Nut
523 5401523 Spacer T-LS.01.06A 1 RX-850 Only Spacer
524 5401524 Bowl 185 2 Bead Breaker Cylinder Seal
525 5401525 Piston T-LS.01.02A 1 Bead Breaker Cylinder Piston
526 5401526 Nut M8 X 1.5 1 M8X1.5 Nut
527 5401527 Cylinder Body T-LS.01.03A 1 Bead Breaker Cylinder Body
528 5400956 Nut M6 12 M6 Nut
529 5400520 Locking Plate G 1/4 1 G1/4 Lock Nut
530 5400502 O-Ring 185 X 5.7 1 Bead Breaker Cylinder O-Ring

5-A 5401534 Bead Breaker 1 Hose Non Threaded RX-950

35
 RX-950/950AT
UNIVERSAL GEAR
SPARE PARTS- BOX
GEARBOX
T-J.00.00 Page 6 of 6

36
 RX-950/950AT GEAR BOX
# Part # Name Specification Qty. BPK Description
601 5400601 Lower Gearbox Housing T-J.00.04 1 Lower Gearbox Housing
602 5400961 Nut M8 5 M8 Nut
603 5400937 Nut M10 18 M10 Nut
604 5400903 Flat Washer 10 24 #10 Washer
605 5400605 Bearing 6208 1 Bottom Bearing
606 5400606 Spindle T-JK.00.01 1 355mm Gearbox Spindle RX-950
606 5400613 Spindle T-JK.00.01 1 325mm Gearbox Spindle RX-850
607 5400607 Disk Key 14 X 55 1 Spindle Key
608 5400608 Bearing 6010 1 Top Bearing
609 5400609 Gear Wheel w/ Support T-J.00.05 1 Gear Wheel
610 5400610 Upper Gearbox Housing T-J.00.04 1 Upper Gearbox Housing
611 5400611 Screw M8 X 30 5 M8X30 Bolt
612 5400903 Flat Washer 10 4 #10 Washer
613 5400941 Screw M10 X 200 4 M10X200 Bolt
614 5400938 Screw M10 X 160 2 M10X160 Bolt
615 5400615 Cap 40 X 25 X 8 1 Worm Gear Seal
616 5400616 Bearing 1 Worm Gear Bearing
617 5400617 Wormscrew T-J.00.09 1 Worm Screw
618 5400618 Disk Key 6 X 30 1 Worm Screw Key
619 5400619 O-Ring 1 Worm Screw Seal
620 5400620 Bearing 1 Worm Screw Bearing
621 5400621 Belt Pulley T-J.00.10A 1 Gearbox Pulley
622 5400962 Screw M8 X 12 1 M8X20 Gearbox Pulley Bolt
607 5400607 Disk Key 14 X 55 1 Spindle Key
608 5400608 Bearing 6010 1 Top Bearing
609 5400609 Gear Wheel w/ Support T-J.00.05 1 Gear Wheel
610 5400610 Upper Gearbox Housing T-J.00.04 1 Upper Gearbox Housing
611 5400611 Screw M8 X 30 5 M8X30 Bolt
612 5400903 Flat Washer 10 4 #10 Washer
613 5400941 Screw M10 X 200 4 M10X200 Bolt
614 5400938 Screw M10 X 160 2 M10X160 Bolt
615 5400615 Cap 40 X 25 X 8 1 Worm Gear Seal
616 5400616 Bearing 1 Worm Gear Bearing
617 5400617 Wormscrew T-J.00.09 1 Worm Screw
618 5400618 Disk Key 6 X 30 1 Worm Screw Key
619 5400619 O-Ring 1 Worm Screw Seal
620 5400620 Bearing 1 Worm Screw Bearing
621 5400621 Belt Pulley T-J.00.10A 1 Gearbox Pulley
622 5400962 Screw M8 X 12 1 M8X20 Gearbox Pulley Bolt
623 5400623 Flat Washer 8 1 #8 Pulley Washer
624 5400624 Belt 686# 1 V-Belt
625 5400625 Motor Pulley T-J.00.08B 1 Motor Pulley
626 5400626 Motor Support 1 Motor Support Bracket
627 5400944 Screw M10 X 45 4 M10X50 Bolt
628 5400628 Seeger Ring 50# 1 M10 Nut
629 5400629 Washer 8 Rubber Motor Mount
630 5400630 Disc Key 1 Motor Shaft Key
631 5400631 Motor 110/200v-50/60hz 1 Motor
37
 RX-950/950AT JET BLAST PEDAL
UNIVERSAL PARTS-
PEDAL UNIT
T-K.01.00 Page 7 of 8

38
 RX-950/950AT JET BLAST PEDAL
# Part # Name Specification Quantity BPK Description
701 5400954 Screw M5 X 30 2 M5X30 Moving Plate Screw
702 5400702 Moving Plate T-K.01.02 1 Moving Plate
703 5400703 Spring T-K.01.03 1 19 X 2.5 X 36 Moving Plate Compression Spring
704 5400950 Nut M5 4 M5 Nut
705 5400705 Fixing Plate T-K.01.04 1 Fixing Plate
706 5400984 Locknut M6 8 M6 Nylock Nut
707 5400956 Nut M6 2 M6 Nut
709 5400709 Rod 3 Air Valve Mounting Rod
710 5400912 Washer 5 2 #5 Washer
711 5400342 Valve Body 1 Valve Body
712 5400973 Elastic Washer 5 2 #5 Plastic Washer
713 5400953 Screw M5 X 25 2 M5X25 Bolt
714 5400934 Union 3 8MM 1/8" Straight Fitting
715 5400715 Stop Washer 2 Air Valve Plug
716 5400344 O-ring 17 X 4 6 17 X 4 O-Ring
717 5400343 Washer 5 Air Valve Spacer
718 5400346 Valve Spindle T-K.01.01 1 Air Valve Shaft
719 5400345 Pin 4 X 20 1 4 X 20 Pin
720 5400905 Ring #12 2 #12 Snap Ring
721 5400721 Shaft 1 Foot Pedal Shaft
722 5400722 Pedal Bracket 1 Foot Pedal Mounting Bracket
723 5400959 Screw M6 X 30 1 M6X30 Bolt
724 5400724 Spring 1 Foot Pedal Return Spring
725 5400301 Pedal 1 Foot Pedal
726 5400726 Support 1 Air Valve Linkage Bracket
727 5400981 Nut M8 1 M8 Nylock Nut
728 5400918 Bolt 1 1/4" to 1/8" Straight Fitting
729 5400729 Valve 1 Jet Blast Pressure Valve
730 5400968 Union 8 G 1/4 1 8MM 1/4" Straight Fitting

39
RX-950/950AT QUICK DEFLATING VALVE
QUICK DEFLATING VALVE SPARE PARTS
Page 8 of 08

40
 RX-950/950AT QUICK DEFLATING VALVE

# Part # Name Specification Quantity BPK Description

801 5400931 Union G 1/4 X 8 1 8MM 1/4" 90* Fitting
802 5400836 O-Ring 45 X 2.65 4 O-Ring
803 5400837 Valve Support T-K.02.03 1 Bottom Block
804 5400838 Positioning Support T-K.02.05 1 Positioning Support
805 5400839 Seeger Ring #28 1 #28 Snap Ring
806 5400847 Sealing Ring T-K.02.06 1 Sealing Ring
807 5400848 Pressing Washer T-K.02.07 1 Press Washer
808 5400914 Flat Washer 6 2 #6 Washer
809 5400984 Locknut M6 1 M6 Nylock Nut
810 5400932 Union G 1/4 X 8 1 8MM 1/4" Tee Fitting
811 5400853 Valve Body T-K.02.02 1 Solenoid Valve Body
812 5400924 Union G 3/8 X 12 4 12MM 3/8" 90* Fitting
813 5400855 Block Up T-K.02.01 1 Top Block
814 5400951 Screw M5 X 16 4 M5X16 Bolt
815 5400846 Support T-K.02.04 1 Deflating Valve Mounting Bracket
816 5400940 Screw M10 X 20 2 M10X20 Bolt
817 5400976 Elastic Washer 10 2 #10 Plastic Washer
818 5400903 Flat Washer 10 2 #10 Washer
819 5400913 Elastic Washer 6 2 #6 Plastic Washer
820 5400958 Screw M6 X 16 2 M6X16 Bolt

41
 L 07 3 L07 1
L0 74
L 075 L07 0
L07 2

PU ¹ Ü
L 03 2
L 034
L 07 7 L0 37 L 036
L0 76

L 03 8

L0 62 L0 61 L 033 L0 01
L0 63

L0 64 L 060
L0 43
L 03 5
L 065 L0 59 L 04 4 L 00 2
L0 66 L 039 L0 31
L0 58 L 045 L0 06 L0 03
L 040
L0 67 L0 30 L 00 4
L 046 L02 9
L0 68

42
L0 41
L 06 9
L0 05
L 028 L 009
L 057
L 027 P U¹ Ü
L0 47
L05 6
L02 6
L0 48 L0 42
L0 55 L 007
L 02 5
L 008
L 052 L0 24
L 05 4
L0 23
L0 51 L0 10
L 053 L0 49 L0 22
L 050 L02 1 L 02 0
L 017
RX-950/950AT ASSIST TOWER

L0 11
L0 19

L0 12

L 018
L0 13
895IT LEFT ASSISTANT L000 PAGE 10 OF 10 L0 16 L 014
L0 15
 RX-950/950AT ASSIST TOWER
# Part # Name Specification Quantity BPK Description
L001 5400960 Screw M6 X 50 2 M6X50 Bolt
L002 5400914 Washer 6 2 #6 Washer
L003 5400856 Rear Box LC310&320.00.22 1 Air Line Guard
L004 5400942 Screw M10 X 25 4 M10X25 Bolt
L005 5400903 Washer 10 4 #10 Washer
L006 5400903 Washer 10 4 #10 Washer
L007 5400857 Screw M12 X 60 2 M12X60 Bolt
L008 5400906 Washer 12 4 #12 Washer
L009 5400858 Support LC335.00.03 1 Left Tower Support Brkt
L010 5400946 Nut M12 X 60 2 M12 Nut
L011 5400175 Screw M10 X 40 4 M10X40 Bolt
L012 5400860 Support LC335.00.02 1 Left Tower Support Brkt
L013 5400404 Screw M12 X 25 3 M12X25 Bolt
L014 5400906 Washer 12 3 #12 Washer
L015 5400906 Washer 12 3 #12 Washer
L016 5400937 Nut M10 4 M10 Nut
L017 5400862 Support LC335.00.02 1 Left Tower Base
L018 5400946 Nut M12 4 M12 Nut
L019 5400857 Screw M12 X 60 4 M12X60 Bolt
L020 5400905 Ring 12 2 #12 Snap Ring
L021 5400864 Shaft LC310&320.00.20 1 Air Cylinder Mounting Shaft
L022 5400906 Washer 12 4 #12 Washer
L023 5400906 Washer 12 4 #12 Washer
L024 5400865 Screw M12 X 40 4 M12X40 Bolt
L025 5400866 Grub Screw M10 X 20 4 M10X20 Set Screw
L026 5400867 Support LC310&320.05.00 1 Left Twr Vert Support
L027 5400951 Screw M5 X 16 2 M5X16 Bolt
L028 5400912 Washer 5 2 #5 Washer
L029 5400868 Support LC310&320.00.19 1 Cylinder Shaft Support
L030 5400869 Silencer 43 X 30.5 X 7.5 1 Felt Washer
L031 5400870 Slide Rail LC310&320.00.05 1 Slide Rail
L032 5400871 Cover LC310&320.00.04 1 Twr Cover
L033 5400965 Screw M8 X 70 6 M8X70 Bolt
L034 5400872 Anti Friction Washer LC310&320.00.03 4 Anti Friction Washer
L035 5400210 Grub Screw M6 X 12 4 M6X12 Set Screw
L036 5400874 Support LC310&320.00.01 1 Assist Arm Support
L037 5400875 Connecting Shaft LC310&320.00.02 1 Assist Arm Connecting Shaft
L038 5400944 Screw M10 X 50 3 M10X50 Bolt
L039 5400876 Ring 27 X 20 X 6 1 27X20X6 O-Ring
43
 RX-950/950AT ASSIST TOWER
L040 5400877 Felt 30 X 20 X 10 1 30X20X10 Felt Washer
L041 5400928 Union 6 G 1/8 2 6MM 1/8" 90* Fitting
L042 5400878 Cylinder LC310&320.01.00 1 Assist Arm Air Cylinder
L043 5400879 O-ring 25 X 3.1 2 25X3.1 O-Ring
L044 5400880 O-ring 100 X 5.7 2 100X5.7 O-Ring
L045 5400881 O-ring 14.5 X 2 1 14.5X2 O-Ring
L046 5400882 O-ring 100 X 3.1 2 100X3.1 O-Ring
L047 5400914 Washer 6 4 #6 Washer
L048 5400957 Screw M6 X 10 4 M6X10 Bolt
L049 5400883 Front Box LC310&320.00.21 1 Cylinder Cover
L050 5400941 Screw M10 X 200 1 M10X200 Bolt
L051 5400903 Washer 10 1 #10 Washer
L052 5400884 Washer 30 X 11 X 3 1 30X11X3 Retaining Washer
L053 5400885 Bead Breaker Shoe LC310&320.00.14 1 Plastic Disc
L054 5400886 Ring 25 1 #25 Snap Ring
L055 5400887 Cover LC310&320.00.10 3 Assist Arm Cover
L056 5400888 Bead Lifting Tool LC330.03.00 1 Assist Arm
L057 5400889 Cover 12 1 Handle/Assist Arm Rt/Lt/R-26EX
L058 5400890 Cover LC310&320.00.13 1 Assist Arm Cone
L059 5400891 Connecting Rod LC310&320.00.11 1 Cone Shaft
L060 5400892 Spring 5 X .6 X 12 1 5X.6X12 Spring
L061 5400893 Screw LC310&320.00.12 1 Set Screw
L062 5400894 Steel Ball 5 1 Steel Ball
L063 5400895 Rotating Arm LC335.02.00 1 Assist Block Arm
L064 5400896 Distance Ring LC335.02.02 1 Spacer
L065 5400897 Cover LC335.02.03 1 Spacer
L066 5400898 Roller LC310&320.00.08 1 Assist Block
L067 5400899 Washer LC310&320.00.09 1 Retaining Washer
L068 5400903 Washer 10 1 #10 Washer
L069 5400940 Screw M10 X 20 1 M10X20 Bolt
L070 5400730 Arm LC335.01.00 1 Air Valve Control Arm
L071 5400940 Screw M10 X 20 1 M10X20 Bolt
L072 5400731 Washer LC310&320.00.06 1 Retaining Washer
L073 5400919 Silencer G 1/8 2 1/8" Silencer
L074 5400732 Valve G 1/8 1 Left/Right Assist Arm Air Valve
L075 5400733 Cover LC310&320.00.07 1 Air Valve Cover
L076 5400949 Screw M4 X 30 3 M4X30 Bolt
L077 5400928 Union 6 G 1/8 3 6MM 1/8" 90* Fitting
44
45
46
 TIRE AND WHEEL DATA
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________
_____________________________________________________________________

47
 For Parts Or Service
Contact:

Bend-Pak Inc. / Ranger Products

1645 Lemonwood Dr.
Santa Paula, CA. 93060

Tel: 1-805-933-9970
Toll Free: 1-800-253-2363
Fax: 1-805-933-9160

www.bendpak.com
www.rangerproducts.com