Checklist + Flow-Procedure

Boeing 767-300ER

DO NOT USE FOR FLIGHT

Boeing 767-300ER

Checklist / Flow-Procedure
including basic Flight-Planning-Charts

for Level-D 767-300ER

with Microsoft Flight Simulator / Prepar3D

created by Carsten Rau

www.CarstenRau.de

Version 7.0
Print Notice: Page size DIN A5. Print 2 pages per A4 or Letter page. This page is the
front cover.

Level-D 767-300ER Created by Carsten Rau (www.CarstenRau.de) Page 1

 Checklist + Flow-Procedure
Boeing 767-300ER

Attention:
LVLD 767 Options Menu Standard settings, IRS Alignment on fast
mode (2min)

Parking Position / Preparation:

• Load & Fuel (at Configurator) Set
--- Note CG trim setting from lead sheet!!! ---
• Dep-Metar Check & note
• Flighplan Create a flightplan (in FSBuild
and save at LvlD dir.)
• FSX Start & load/create 747-flight
• Dark & Cold Load D&C panel setting
• Load & Fuel (at FSX) Check (or reset)
• Parkingbreak Set
• Dark & Cold (at Configurator) Load (if needed)
• IVAP-Connection Activate
• Door(s) Open
• Gangway Enable (if available) (Ctrl + J)
➔ OVHP only:
• Battery On
• Standby Power Auto
• APU GEN switch Push
• Bus Tie switches Auto
• Utility Bus switches On
• GENerator CONTrol switches Pushed in
• Panel lights
o PANEL/FLOOD On (if needed)
o LT OVRD (Dome) On (if needed)
• Ext Pwr Request (from ground crew)
---wait till Ext Pwr available---
• Ext Pwr switch On
• APU Start ➔ On
---wait till APU Run light illuminates---
• Ext Pwr Off / Disconnect (call ground
crew)
• POS lights On

Level-D 767-300ER Created by Carsten Rau (www.CarstenRau.de) Page 2

 Checklist + Flow-Procedure
Boeing 767-300ER

• IRS Alignment (OVHP & FMC):

o IRS switches (1-3) Off
o IRS switches (1-3) Nav
---wait till ON DC light flashes and then ALIGN light is illuminated---
o DSPL SEL knob PPOS
o SYS DSPL knob IRU L, C or R
o ➔ FMC:
▪ ( Index page Go to… )
▪ Ident page 1L
▪ Pos Init page 6R
▪ Look-up Coordinates Shift + z (/or enter 4-letter
airport code & press 2L)
▪ Coordinates to IRS Enter + 5R (/or copy airport
position to IRS; 2R ➔ 5R)
• Yaw Dampers On (both)
• EEC switches On (both)
• Hydraulic panel:
o Primary engine pumps On
o Primary electric switches Off
o Demand pump switches Off
• Overhead Cautions Check (no abnormal warnings)
• HF radio Off
• Electrical panel:
o All switches Pushed in
• Cockpit Voice Recorder Button Test
• Emergency Light switch Armed
• Passenger Oxygen switch Blank
• Ram Air Turbine switch Blank
• Ignition switch 1: odd days / 2: even days /
both: cold weather
• Engine Start selectors Auto
• Fuel Jettison Panel:
o All switches Blank
o Selector Off
• Fuel Panel:
o All fuel pumps Off
o Crossfeed Off

Level-D 767-300ER Created by Carsten Rau (www.CarstenRau.de) Page 3

 Checklist + Flow-Procedure
Boeing 767-300ER

• Fuel quantity and balance Check

• Engine & Wing anti-ice Off (on under 10°C TAT)
• Cargo heat Off
• Window heat On
• Passenger Signs:
o No smoking On
o Seatbelts Auto
• Cabin Alt. Control:
o Mode Select Auto1: odd days /
Auto2: even days
o Auto Rate Detent position (black marking)
• Equipment Cooling Auto
• Temp. Control (Cabin & Flt Dk) Auto (or as required)
• Trim Air On
• Recirculation Fan switches On
• Packs:
o APU in use Both Packs Auto
o External Air Both Packs Off
• Isolation switches L & R On
• Isolation C On & guarded
• Engine Bleed switches On
---APU should now run at least 1min---
• APU Bleed On
➔End OVHP only
• FMC
- Clear messages ➔ CLR
- Route Page ➔RTE
- Enter company route [read: enter flightplan-name (created in FSBuild)]
➔ 3R
- Enter flight number (example DHL458 => Lufthansa Flt. 458) ➔ 2R
- Activate ➔ 6R ➔ Exec
- DEP/ARR page ➔ DEP/ARR btn.
- Set SID (standard departure route) (if required)
o 1. Choose active Rwy
o 2. Choose SID
- Performance initialization page ➔ PERF INIT
- Enter ZFW (in 1000 LBS) ➔ 3L

Level-D 767-300ER Created by Carsten Rau (www.CarstenRau.de) Page 4

 Checklist + Flow-Procedure
Boeing 767-300ER

o Zero Fuel Weight = Operating Empty Weight

(OEW=197.000LBS) + Load
o Load = Weight of passengers and cargo (in LBS)
o Maximum ZFW = 288.000 LBS
---GW (Gross Weight) should now auto-fill in L1---
- Enter Reserve Fuel (in 1000 LBS) ➔ 4L
- Enter FL / altitude ➔ 1R (max FL for 767 = FL430)
- Enter Cost Index (0 to 9999) (80 eco cruise, 100 normal cruise)➔ 2R
- Enter step climb value (2000 for RVSM, 4000 for ICAO standard) ➔ 5R
- Takeoff Reference page (1 / 2) ➔ 6R
- Modify Thrust settings if needed
- Takeoff Reference page (2 / 2) ➔ Next Page
- Enter temperature (xx = °C) ➔ 5R
- Enter winds (xxx/xx = heading/knots) ➔ 3L
- Enter rwy condition (/D or /W = dry or wet) ➔ 5L
- Takeoff Reference page (1 / 2) Prev Page
- Enter flaps setting (standard 5) ➔ 1L
- Enter CG trim setting (from load sheet / Center of Gravity / example 26)
➔ 3L
---V1, VR and V2 should be auto-filled now (note V2)---
--- PRE-FLT column should say COMPLETE now---
- Legs page ➔ LEGS
- Delete any discontinuities
• EHSI Control panel route check (optional):
o EHSI control knob PLAN
o Range knob 40nm (or as required)
o FMC Legs page LEGS
o FMC stepwise forward STEP ➔ 6R
---when finished checking route---
o EHSI control knob MAP
o FMC Init Ref page INIT REF
• IVAP-flightplan Read from FMC or FSBuild &
note/enter in IVAP FP
• MACH at flightplan Enter in IVAP FP
(eco cruise Mach 0.80)
• Departure Time enter
• EFIS-Range (MP) 40nm (or as required)

Level-D 767-300ER Created by Carsten Rau (www.CarstenRau.de) Page 5

 Checklist + Flow-Procedure
Boeing 767-300ER

• Altimeter Set to atmospheric pressure (B)

• Nav1 Radio Auto

• F/D (AP) On
• A/T (AP) Off
• IAS/MACH (AP) Set to V2 speed
• HDG (AP) Set rwy heading
• Altitude (AP) Set first altitude
• AP Disengage Bar Up
• Nav2 Radio Auto (F/O panel)
---continue when IRS alignment finished---
• Instrument Source selectors Norm
• Airspeed Set in analogue gauge (auto:
click lower left corner)
• RDMI Set pointer controls
& verify headings
• EADI Check
• EHSI Check (range & display mode
as required)
• ASA Blank
• Altimeter Set
• VSI Check indicates 0
• Clock Set
• Standby Instruments Set
• Warning Annunciators Check all off

• Standby Engine gauges Auto

• Autobreak Off
• EICAS Check for messages
• EICAS Engines page
• Thrust Rating Panel:
o Set T/O T/O
o Set derate setting Non, Clb1 or Clb2
• Flap indicator Check 0
• Alternate flap selector Norm
• Landing gear Down & Green

Level-D 767-300ER Created by Carsten Rau (www.CarstenRau.de) Page 6

 Checklist + Flow-Procedure
Boeing 767-300ER

• Alternate gear switch Guarded off

• GND PROX Ovrd switches Off (F/O panel)
➔ Pedestal only:
• Parking break Check set
• Stab Trim Cutout switches Norm
• Spoilers Down
• Throttles Closed
• Fuel Control switches Cut off
• Flaps Up
• Engine & APU Fire Panel Normal (no handle pulled)
• Cargo Fire Panel Normal
• Squawk Set
• Squawk Auto
• Comm Panel Set
• Audio Panel Set (active ATC or Unicom 122.8)
• ILS frequency PARK or Set (or auto-set by FMC)
• Aileron & Rudder Trim Set 0
• TCAS switch TA/RA
➔End Pedestal only
• IFR-clrc Request (when ATC active)
• FP-correction Correct (if required / requested)
• IFR-clrc-data Note & Readback
--- Note Squawk, First-Altitude, QNH, SID ➔ Readback ---

Engine s/u & Pushback:

• Cargo Heat switches On
• Passenger Signs On
• Inform Crew Press ALERT button
• Gangway Disable (Ctrl + J)
• EICAS messages Cancel
• Primary Electric pumps On
• Demand Pumps Auto
• Fuel pumps On (all tanks containing fuel)
• Red Anti-collision lights On
• Packs Off
• Stabilizer Trim Set (as indicated on load sheet)

Level-D 767-300ER Created by Carsten Rau (www.CarstenRau.de) Page 7

 Checklist + Flow-Procedure
Boeing 767-300ER

• EICAS Status page

• Flight Controls Check
• EICAS Engine page
• Doors Closed

• Engine s/u & Pushback p/b clrc Request

• Parking break Off
• Pushback
o Start via IVAP
or
o Start via GND CALL (p/b, start &
interphone disconnect)
• Start Selector R GND
---wait till N2 reaches 18% on lower EICAS Engine page---
• Fuel Control switch R Run
---At 50% N2 Start Selector should go back to Auto---
• Start Selector L GND
---wait till N2 reaches 18% on lower EICAS Engine page---
• Fuel Control switch L Run
---At 50% N2 Start Selector should go back to Auto---
• Generator lights Check off
• APU Off
• ( Engine anti-ice On under 10°C )
• Isolation switches Closed
• Packs Auto
• Autobreak selector RTO
• EICAS Check for abnormal msgs.
• ( Ground equipment Clear )

• Taxi Lights On
• Runway turn-off lights On
• Nose wheel landing lights On
• Pushback Finish

Level-D 767-300ER Created by Carsten Rau (www.CarstenRau.de) Page 8

 Checklist + Flow-Procedure
Boeing 767-300ER

Taxi:
• Taxi-Clrc Request
• Taxiways Note if needed
• Ground-Guidance Request if needed
• FMC (optional 1 / 2):
o Takeoff Ref. page (1 / 2) ➔ INIT REF
o Set TOGW (TOGW = GR WT – consumed taxi fuel) ➔ 4R
o “T/O Speeds Deleted” message will appear ➔ CLR (clear message)
o New T/O Speeds will be auto-filled
• Airspeed (optional 2 / 2) Set analogue airspeed gauge
(click left lower corner)
• Flaps Select (as filled in FMC / e.g. 20°)
• Notify Crew Press ALERT button

h/p:
• Hand-off GND to TWR Change frequency
• l/u & t/o clrc Request (rdy for dep h/p xx)
• Landing lights On (all now)
• Anti-collision lights On (all now)
• IVAP-Transponder ein
• Postion & hold Taxi & stop on rwy

Ready to Takeoff:
• Parkingbreak Activate
• Autothrottle (AP) On
• AP settings Check (FD on, HDG, IAS, ALT)
• N1 button (AP) On
• Thrust Levers Forward (fully fwd position)
• Parkingbreak Release
• Yoke (till 80 knots) Press forward
• V1 No abort of take-off
• VR Lift nose up
• V2 Lift-off

Level-D 767-300ER Created by Carsten Rau (www.CarstenRau.de) Page 9

 Checklist + Flow-Procedure
Boeing 767-300ER

Takeoff:
• Trim settings Adjust (when needed)
• Gear Up (at positive climb rate >500ft)
---above 400ft AGL---
• HDG SEL On
---above 1000ft AGL---
• FL CH On
---above 1500ft AGL---
• Autopilot On (1 of 3) (normal C)
• Flaps Raise
• Landing gear lever Off position
• Airborne Publish on Unicom (no ATC)
• Starttime Note (if needed)
• FMC:
o Legs page ➔ LEGS
o Copy first waypoint ➔ 1L or 2L
o Set as dct waypoint ➔ 1L
o Exec light illuminates, press ➔ EXEC
• LNAV (AP) On
• VNAV (AP) On

Climb:
• Landing-/Taxi Lights Off
--- to final FL / when cleared to next flight level ---
• AP altitude (& speed) Change (FL CH when VNAV is
not enabled)
---do the following things if required---
• Hand-off to APP/CTR Change frequency
• Engine & Wing anti-ice On (under 10°C TAT)
• Altimeter Readjust (above 18000ft)

Cruise:
• Radio /ATC contact Maintain
• Autopilot / FMC Check permanently

Level-D 767-300ER Created by Carsten Rau (www.CarstenRau.de) Page 10

 Checklist + Flow-Procedure
Boeing 767-300ER

• FMC Check PROGress page for fuel

consumption
---when center fuel tank empty---
• Center fuel pump Off

Descent & Approach:

--- Before reaching Top of Descent (T/D) ---
• Descent preparations Begin
• Airport-/Meta-Information Retrieve
• Autobreaks Set
• FMC:
o Arrivals page ➔ DEP/ARR
o Set active rwy (and approach/STAR)
o Approach Ref page ➔ INIT REF button
o Copy flap and corresponding Vref setting ➔ 1R, 2R or 3R
o Paste for approach ➔ 4R
o Note approach speed (see 4R)
o NAV Radio page ➔ NAV/RAD
o Note rwy heading (see 4L)
o Close FMC
• Notify crew ALERT button
• Start of Descent (4 possibilities):
o VNAV:
▪ Alt (AP) Set (before reaching T/D !)
▪ VNAV Will descent automatically at T/D
o DES NOW:
▪ Alt (AP) Set (before reaching T/D !)
▪ FMC ACT ECON CRZ page ➔ VNAV
▪ Page 2 Next Page
▪ Des Now 6R
▪ Execute EXEC
o FL CH:
▪ Alt (AP) Set
▪ FL CH (AP) On
▪ Speed (AP) Set to IAS, set Speed

Level-D 767-300ER Created by Carsten Rau (www.CarstenRau.de) Page 11

 Checklist + Flow-Procedure
Boeing 767-300ER

o Change Cruise Alt:

▪ FMC ACT ECON CRZ page ➔ VNAV
▪ Alt (FMC) Enter in Scratchpad
▪ Cruise Alt (FMC) Set ➔ 1L
▪ Execute EXEC
• Speedbrakes Up (as required)
• Flaps Lower (as required)
• Altimeter Readjust (under 18000ft)
• Flight Instruments & Radios Set
• Airspeed bugs Set analogue gauge (click left
lower corner)
• Hand-off CTR to APP Change frequency
• Landing lights On
• Taxi light On

Final approach & Landing (Autoland):

• Flaps Lower (if F/O on, as announced)
• Gear Down (under 270kt /
at least at flaps 20)
• Speedbrake Retract & Armed
• ILS captured Announce
• LOC (AP) On (to follow ILS localizer)
• APP (AP) On (to follow ILS glideslope path)
---check, when APP pressed, LOC, VNAV off, 3 AP on---
• Hand-off APP to TWR Change frequency
• Landing clrc Request
---Touchdown---
• Throttles Idle
• Thrust reversers Engage (if needed)
• Thrust reversers Disengage under 80kt, thrust idle
• Autopilot (AP) Disengage
• A/T (AP) Off
• F/D (AP) Off
• Runway Vacate („rwy vacated“)

Level-D 767-300ER Created by Carsten Rau (www.CarstenRau.de) Page 12

 Checklist + Flow-Procedure
Boeing 767-300ER

Final approach & Landing (w/o Autoland):

• Flaps Lower (continue as indicated)
• Gear Down (under 270kt / at flap 20)
• Speedbrake Retract & Armed
• ILS captured Announce
---check flaps to set degree and gear down---
• Hand-off APP to TWR Change frequency
• Autopilot (AP) Disengage (Disengage bar down)
• A/T (AP) Off
• F/D (AP) Off
• Trim settings Adjust (when needed)
• Landing clrc Request
---Touchdown---
• Throttles Idle
• Thrust reversers Engage (if needed)
• Thrust reversers Disengage at 80kts, thrust idle
• Runway Vacate („rwy vacated“)

Taxi:
• Transponder Stdby
• Hand-off TWR to GND Change frequency
• Taxiways Note and follow
• ( Ground-Guidance Request if required )
• Flaps Set 0
• Stab Trim 4 units
• Speedbrake Down (if engaged)
• Autobrakes Off
• Landing lights Off (Nose Landing lights stay on)
• White anti-collision lights Off
• Landing time Note (if needed)
• APU Start

Parking Position:
• Parking brake Set
• ATC contact End (state “on blocks”)
• Engine anti-ice Off

Level-D 767-300ER Created by Carsten Rau (www.CarstenRau.de) Page 13

 Checklist + Flow-Procedure
Boeing 767-300ER

• Isolation switches On
• Ext Pwr Request from ground crew
• Fuel control switches Cut off
• Seat Belts Off
• Primary Electric pumps Off
• Demand pumps Off
• Primary Engine pumps Stay on
• Fuel pump switches Off
• Red anti-collision lights Off
• Door s Open (shift + e)
• Gangway Enable (strg + j)

---Aircraft ready for turn-around /next flight---

---Continue if Dark&Cold needed---

• OVHP operations (from pages 1 & 2) Work backwards

--- everything to off/stdby ---

• IRS selectors Off

• Emergency light Off
• Window heat Off
• Cargo heat Off
• Packs Off
• TCAS Stdby
• If still on APU (no Ground power):
o APU Off
o APU Bleed Off
• Ground power Off
• External lights Off (all)
• Internal lights Off (all)
• Bus Tie Switches Off
• Stdby power selector Off
• Battery Off

Level-D 767-300ER Created by Carsten Rau (www.CarstenRau.de) Page 14

 Checklist + Flow-Procedure
Boeing 767-300ER

Intentionally Blank

Level-D 767-300ER Created by Carsten Rau (www.CarstenRau.de) Page 15

 Checklist + Flow-Procedure
Boeing 767-300ER

Fuel-Planning-Charts:

Flight Plan Fuel only!

Level-D 767-300ER Created by Carsten Rau (www.CarstenRau.de) Page 16

 Checklist + Flow-Procedure
Boeing 767-300ER

Fuel Planning Continued:

Operating Empty Weight 197.000 LBS

+ Payload XXX.XXX LBS
= Zero Fuel Weight XXX.XXX LBS
+ Minimum Landing Fuel 012.000 LBS
+ Alternate Fuel (200nm dist.) 006.000 LBS
+ Contingency Fuel 012.000 LBS
+ Flight Plan Fuel XXX.XXX LBS
= Planned Takeoff Weight XXX.XXX LBS

➔Flight Plan Fuel + 30.000 LBS = Total Fuel

➔ Total fuel = Enough fuel for route, 1h contingency (holding & taxi),
problematic winds, alternate fuel for 200nm and a minimum landing fuel
(1h). Modify alternate value as needed.
➔ Load wing tanks first, with same amount of fuel; wing tanks full ➔ center
tank.

Max Weights:
Maximum Takeoff Weight 408.000 LBS
Maximum Landing Weight 310.000 LBS
Maximum Zero Fuel Weight 196.000 LBS

Trim examples, empty 767-300ER:

45.000 LBS ➔ 22%/2,2
100.000 LBS ➔ 26%/2,7
140.000 LBS ➔ 21%/4,5
160.000 LBS ➔ 19%/5,2

Level-D 767-300ER Created by Carsten Rau (www.CarstenRau.de) Page 17

 Checklist + Flow-Procedure
Boeing 767-300ER

Lights panel as printed in freely the available 767 manual at

http://www.leveldsim.com:

Recommendation: Print pages 7 to 12, 27 and 184 from the 767 manual.

Level-D 767-300ER Created by Carsten Rau (www.CarstenRau.de) Page 18