18-NOV-2022 56312E39

RYS8833

Ultra Low Power 1.8V UART/I2C interface GNSS module

Datasheet

11mm*8mm*2.2mm
 RYS8833
Ultra-low power GNSS Module

PRODUCT DESCRIPTION
The RYS8833 1.8V GNSS module is a multi-GNSS module with high sensitivity, The RYS8833 also has
integrated digital noise filters and spectrum analyzer.

FEATURES
• SONY CXD5605AGF Engine.
• A multi-GNSS module for GPS(L1 C/A), GLONASS(L1 OF), SBAS(L1 C/A), QZSS(L1 C/A), Galileo(E1
CBOC), and BeiDou(B1, specific Firmware).
• Including SAW filter, LNA and TCXO.
• Embedded digital noise filters and spectrum analyzer.
• UART / I2C Interface optional.

BLOCK DIAGRAM

RYS8833
Dotted line is LNA
option

Filter

• Flash
32.768KHz LNA
•
Oscillator
• SONY
CXD5605AGF TCXO
•Switching multi-GNSS receiver
•Power
`

RXD TXD
SYSTEM0 SCL SDA PPS

Processor

Copyright © 2022, REYAX TECHNOLOGY CO., LTD. 2

 RYS8833
Ultra-low power GNSS Module

PIN DESCRIPTION

U1

30

29

28

27

26

25

24

23
RY S8833

NC

NC

NC

NC

NC
GND

GND
RF_IN
1 22
GND GND
2 21
NC CTS
3 20
LDO2_OUT RTS
4 19
VDD RXD
5 18
VDD_LDO_IN TXD
6 17
LDO1_OUT PPS_OUT

RTC_CLK_IN
SEN_IRQ_IN
7 16

BOOT_REC
GND GND

EXTLD_IN
SYSTEM0
I2C_SDA

I2C_SCL

RST_X
8

10

11

12

13

14

15
Pin Name I/O Condition
1,7,16,22,26,28 GND - Ground
2,23,24,25,29,30 NC - Leave Unconnected.
3 LDO2_OUT O LDO output for memory core blocks.
4 VDD I Power Supply and I/O Voltage.
5 LDO_IN I LDO0 / LDO1 Input
6 LDO1_OUT O LDO output for digital block.
8 I2C_SDA I/O I2C SDA *If not used, Please Leave Unconnected.
9 I2C_SCL I/O I2C SCL *If not used, Please Leave Unconnected.
10 BOOT_REC I/O Reserved, Connect to GND.
11 SEN_IRQ_IN I Interrupt input. *If not used, Please Leave Unconnected.
12 RST_X I Reset input.
13 RTC_CLK_IN I RTC 32.768KHz clock input,
The pin must be connected to GND, If not used.
14 SYSTEM0 I VDD : UART Interface, GND : I2C Interface.
15 EXTLD_IN I Timing signal input, from LTE module.
*If not used, Please Leave Unconnected.
17 PPS_OUT O Time pulse output.
18 TXD/SCL O Serial interface Output / I2C interface
19 RXD/SDA I/O Serial interface Input / I2C interface
20 Reversed - Leave Unconnected.
21 Reversed - Leave Unconnected.
27 RF_IN I GNSS RF Signal input.

Copyright © 2022, REYAX TECHNOLOGY CO., LTD. 3

 RYS8833
Ultra-low power GNSS Module

APPLICATION SCHEMATIC (UART Interface)

VDD
U1
RY S8833_Lite

L1 C1
27nH 0.1uF

CON-P1
U.FL-R-SMT-1
RESET_N

GND
VDD

RXD

TXD

RF_IN
1

VDD
RESET_N

U3
30

29

28

27

26

25

24

23
VDD RY S8833
RXD

TXD

LED1
NC

NC

GND

GND

NC

NC

NC
RF_IN
RED 0805

1 22
GND GND
C2 2 21 R1
4.7uF NC CTS 1K
LDO2_OUT 3 20
LDO2_OUT RTS
4 19 RXD
+1.8V VDD RXD
C3 5 18 TXD
4.7uF VDD_LDO_IN TXD Q1
LDO1_OUT 6 17 P04/1PPS_OUT AO3418
LDO1_OUT PPS_OUT
RTC_CLK_IN
SEN_IRQ_IN

7 16
BOOT_REC

GND GND
EXTLD_IN
SYSTEM0
I2C_SDA

I2C_SCL

RST_X
8

10

11

12

13

14

15

VDD +1.8V
U3
SYSTEM0

S-1206B18-M3T1G
1 3 R3 R2
G

I O 100K 100K
RESET_N
2

C4 C5
10uF 0603 10uF 0603

R5
0 +1.8V
R4
NC

Title
RYS8833_Lite
Size Document Number Rev
Custom<Doc> 1.1

Date: Tuesday , September 01, 2020 Sheet 1 of 1

Copyright © 2022, REYAX TECHNOLOGY CO., LTD. 4

 5
Ultra-low power GNSS Module
RYS8833

For GNSS Active antenna

+3.3V
L1 C1
27nH 0.1uF
CON-P1
APPLICATION SCHEMATIC (Use buck regulator)

U.FL-R-SMT-1

RF_IN
+3.3V
U1

30

29

28

27

26

25

24

23
REY AX RY S8833
D1

NC

NC

GND

GND

NC

NC

NC
RF_IN
GREEN 0805
1 22
GND GND
C2 2 21
4.7uF NC CTS R1
LDO2_OUT 3 20 1K
LDO2_OUT RTS
4 19 RXD
GNSS_+1.8V VDD RXD
5 18 TXD
C3 VDD_LDO_IN TXD Q1
47uF Buck Regulator 6
LDO1_OUT PPS_OUT
17 P04/1PPS_OUT AO3418

RTC_CLK_IN
SEN_IRQ_IN
7 16

BOOT_REC
GND GND

EXTLD_IN
SYSTEM0
U2 R2

I2C_SDA

I2C_SCL
ADI LTC3549EDCB 100K

RST_X
1 6
VIN VFB
2 5 GNSS_+1.8V

10

11

12

13

14

15
GND RUN
3 4
SW MODE

RTC_CLK_IN
R3 C5

SYSTEM0
RST_X

Copyright © 2022, REYAX TECHNOLOGY CO., LTD.

C4 51K 220pF R5
4.7uF L2 R4 NC
TDK VLF3012AT-3R3MR87 NC
LDO_IN
+0.92V
C6
4.7uF B1
SKQGADE010 GNSS_+1.8V
Title
REYAX RYS8830 APPLICATION
LDO1_OUT Size Document Number Rev
Custom<Doc> 1.0
Date: Thursday , October 07, 2021 Sheet 1 of 1
 RYS8833
Ultra-low power GNSS Module

SPECIFICATION
Item Min. Typical Max. Unit Condition
Power Supply Voltage 1.71 1.8 1.89 V VDD
0.9 1.8 1.95 V VDD_LDO_IN
GNSS continuous mode
Satellite acquisition Current 19 mA
Satellite tracking Current 13 mA
Idle Current 3.7 mA Waiting for command
Sleep2 mode current 0.2 mA
Satellite acquisition Current 11.5 mA Use buck regulator
Satellite tracking Current 8.2 mA Use buck regulator
Idle Current 3.3 mA Use buck regulator
Sleep0 mode current 0.5 mA Use buck regulator
Sleep1 mode current 0.26 mA Use buck regulator
Sleep2 mode current 0.26 mA Use buck regulator
GNSS low power mode
Satellite tracking average 2.6 8.2 mA Use buck regulator
current @GSOP command
Sleep1 and normal mode cycle
I2C slave I2C clock : 400kHz
Address length : 7 bits
Slave address : 0x24
Default Baud Rate 115200 bps 8,N,1
Digital input level high 0.7*VDD VDD+0.3 V VIH
Digital input level low -0.3 0.3*VDD V VIL
Digital output level high 0.8*VDD VDD V VOH 2mA
Digital output level low 0 0.2*VDD V VOL 2mA
Flash size 8 M-bit
1561.098 MHz BeiDou
GNSS Center Frequency 1575.42 GPS
1602.5625 Glonass
Navigation update rate 1 Hz
Accuracy 1 M Signal strength is -130dBm
Cold starts 35 Sec. Signal strength is -130dBm
Hot starts 1 Sec.
Tracking Sensitivity -161 dBm

Copyright © 2022, REYAX TECHNOLOGY CO., LTD. 6

 RYS8833
Ultra-low power GNSS Module

Hot starts Sensitivity -160 dBm

Cold starts Sensitivity -147 dBm
Velocity <0.1 m/s The measured value is based
on the condition of measured
with simulator, and receiver
moved at the constant speed
(20km/h)
Operating Temperature -40 25 +85 ˚C
Dimensions 11mm*8mm*2.2mm
Weight 0.37 g

Copyright © 2022, REYAX TECHNOLOGY CO., LTD. 7

 RYS8833
Ultra-low power GNSS Module

REFLOW SOLDERING
Consider the "IPC-7530 Guidelines for temperature profiling for mass soldering (reflow and wave) processes, published 2001. Only
single reflow soldering processes are recommended for REYAX modules. Repeated reflow soldering processes and soldering the
module upside down are not recommended.

Preheat phase
Initial heating of component leads and balls. Residual humidity will be dried out. Please note that this preheat phase will not replace
prior baking procedures.
• Temperature rise rate: max. 3 °C/s If the temperature rise is too rapid in the preheat phase it may cause excessive slumping.
• Time: 60 - 120 s If the preheat is insufficient, rather large solder balls tend to be generated.
Conversely, if performed excessively, fine balls and large balls will be generated in clusters.
• End Temperature: 150 - 200 °C If the temperature is too low, non-melting tends to be caused in
areas containing large heat capacity.

Heating/ Reflow phase

The temperature rises above the liquidus temperature of 217°C. Avoid a sudden rise in temperature as the slump of the paste could
become worse.
• Limit time above 217 °C liquidus temperature: 40 - 60 s
• Peak reflow temperature: 245 °C

Cooling phase
A controlled cooling avoids negative metallurgical effects (solder becomes more brittle) of the solder and possible mechanical
tensions in the products. Controlled cooling helps to achieve bright solder fillets with a good shape and low contact angle.
• Temperature fall rate: max 4 °C/s To avoid falling off, the REYAX module should be placed on the topside of the motherboard
during soldering.

[°C] Y值
Preheat Heating Cooling
250 Peak Temp245°C
Liquidus temperature
217
200
40-60s Max 4°C/s

150
End Temp Typical Leadfree
Soldering Profile
Max 3°C/s 150-200°C

100 Y值

50
60-120s

0
0 50 100 150 200 250 300
座標軸標題
Elapsed Time

Recommended soldering profile

Copyright © 2022, REYAX TECHNOLOGY CO., LTD. 8

 RYS8833
Ultra-low power GNSS Module

DIMENSIONS

Unit : mm

Copyright © 2022, REYAX TECHNOLOGY CO., LTD. 9

 RYS8833
Ultra-low power GNSS Module

LAYOUT FOOTPRINT RECOMMENDATIONS

Unit : mm

Copyright © 2022, REYAX TECHNOLOGY CO., LTD. 10

 RYS8833
Ultra-low power GNSS Module

GNSS Monitor software

STEP 1. INSTALL THE SOFTWARES
1.) Download the GNSS_Monitor2_ForCustomer_Setup(contact REYAX sales)

STEP 2. CONNECTION SETTING

Plug USB to TTL cable to connect the RYS8833_lite and the PC.
1.) Open the software GNSS_Monitor2_ForCustomer Target →RYS8833 select CXD5605
2.) Open the Serial Port setting
3.) Set the COM port number and the baud rate (Default is 115200bps).
4.) If connection successful, will show FW version message.

Copyright © 2022, REYAX TECHNOLOGY CO., LTD. 11

 RYS8833
Ultra-low power GNSS Module

STEP 3. Command input setting

1.) Click “IDLE” button, Terminal window will show [GSTP]Done.
2.) Click “Satellite Selection” button, after select Satellite and click “Send”. Terminal window will show
[GNS]Done.
3.) Click “Hot start” button, Terminal window will show [GSR]Done. Module start output NMEA log.
4.) If want to stop tracking, click “IDLE” button.

*For detailed command user guide, please refer to RYS8830_RYS8833_Software_Guide

QUICK START GUIDE

STEP 1. Power on module
STEP 2. Issue command
1.) @GSTP // Positioning stop
2.) @GNS 47 // Positioning-use satellite use GPS + GLONASS + SBAS + QZSS L1-CA + QZSS L1-S
3.) @GTIM 2022 12 20 00 00 00 // inject UTC time
4.) @GPPS 1 // enable 1PPS function
5.) @GSR // hot start
*For detailed command user guide, please refer to RYS8830_RYS8833_Software_Guide

E-mail : [email protected]
Website : http://reyax.com

Copyright © 2022, REYAX TECHNOLOGY CO., LTD. 12