BILL OF MATERIALS REV CHANGE CHK'D DATE

ITEM QTY PART NUMBER DESCRIPTION STANDARD

$01 1 FYTB 12 TF Y BEARING FLANGED UNIT SKF
AS 1111 - M5 x 25 01 RELEASED A.T. 04/01/2017

$02 4 BSP35B12-N-12 SPROCKET 35B Series MISUMI ISO metric hexagon commercial bolts and screws
$03 6 35BB20H BALL BEARING IDLER SPROCKET TSUBAKI
$05 2 25-2525-1820 T-SLOTTED ALUMINUM PROFILE 80/20 INC $03 $03
$06 3 25-2525-43 T-SLOTTED ALUMINUM PROFILE 80/20 INC $03
$07 56 141664 T-NUT 80/20 INC $03
$08 4 6001-2Z BALL BEARING SKF
$09 2 STWS12 RETAINING RING C-TYPE MISUMI 011
$10 2 CHE35-430 CHAIN MISUMI
$11 4 STWS14 RETAINING RING C-TYPE MISUMI 002_OPP 012
$12 1 AT10-16 TOOTHED PULEEY POLYTECH DESIGN 009 $02
001 8 LILA-020B-02-001 SUPPORT BASE DETAIL
002 2 LILA-020B-02-002 BEARING SUPPORT SHN DETAIL 020 010
003 4 LILA-020B-02-003 COVER BEARING DETAIL 009 003
004 1 LILA-020B-02-004 SHAFT DETAIL $11
005 4 LILA-020B-02-005 SPACER DETAIL
006 5 LILA-020B-02-006 KEY DETAIL 007
007 1 LILA-020B-02-007 SHAFT DETAIL
DETAIL V DETAIL W
008
009
2
3
LILA-020B-02-008
LILA-020B-02-009
GUIDE SHN
SHAFT
DETAIL
DETAIL SCALE 1 / 3 SCALE 1 / 3 W
010 2 LILA-020B-02-010 ADJUST ANGLE DETAIL
011 1 LILA-020B-02-011 BLOCK DETAIL 002
012 424 LILA-020B-02-012 PLATE DETAIL
013 2 LILA-020B-02-013 ANGLE DETAIL
008_OPP
014 2 LILA-020B-02-014 GUIDE DETAIL
015 2 LILA-020B-02-015 SUPPORT DETAIL 009 001
016 2 LILA-020B-02-016 SUPPORT DETAIL
017 2 LILA-020B-02-017 SPACER DETAIL 008
018 1 LILA-020B-02-018 ANGLE DETAIL
$10
019 1 LILA-020B-02-019_ TOOTHED PULEEY DETAIL
008
020 1 LILA-020B-02-020 ANGLE DETAIL 015
021 2 LILA-020B-02-021 ANGLE DETAIL
003
022 3 LILA-020B-02-022 PLATE DETAIL
$08 $02
002_OPP 2 LILA-020B-02-002_OPP BEARING SUPPORT OPP DETAIL 021 001
008_OPP 2 LILA-020B-02-008_OPP GUIDE OPP DETAIL

002 014 015 014

V $05
$01 022

018 013

001
$12 014
$05
019 008_OPP
016 DETAIL U $09
013 SCALE 1 / 3
017 U 005
001 006 004 $08
THIS DRAWING MAY USE BOTH INCH AND METRIC METRIC - EXCEPT AS NOTED TOLERANCES SHALL BE: ALL EDGES OF PART CONTACT SURFACES ON LOCATING UNIT No.: 01 DESIGN SOURCE DESIGNER PROJECT MGR. SYSTEM NAME SCALE SHEET RELEASE DATE
UNITS OF MEASUREMENT 1 PLACE MACHINING `0.3 BLOCKS AND FINGERS TO HAVE .12R INCH / 3.00 mm MOVIL PART
(*INDICATES INCH DIMENSIONS) 1 PLACE FABRICATION `1.5
2 PLACE `0.08 BETWEEN MACHINED SURFACES
AFTER SPOTTING.
WEIGHT (KG): N/A
FIXED PART
HOGARCIA I.SALVADOR
DESIGN SUP.
LILA NONE 1 OF 23 04/01/2017
MAXIMUM ALLOWANCE ROUGHNESS OF ALL `0.03 BETWEEN SINGLE DOWEL AND A HEEL SURFACE MARK INDENTIFICATION AND MATERIAL NUMBERS ON DETAILS. DETAILER A.TORRES DESCRIPTION

DRAWING No.
SHOWN
METRIC. `0.03 BETWEEN DOWELS IN THE SAME PLANE PAINT INDENTIFICATION NUMBERS ON STRUCTURAL WORK.
BLACK OXIDE CHECKER
1 PLACE mm FINISH DIMENSIONS TO BE 3.2 MICRONS
2 PLACE mm FINISH DIMENSIONS TO BE 1.6 MICRONS
`0.10 BETWEEN DOWELS IN DIFFERENT PLANES
`0.13 TO SCREW HOLES, NON ACCUMULATIVE NOTE: DRAWINGS PROPERTY OF BECKTON DICKINSON.
CUSTOMER H.GARCIA
A.TORRES LILA ASSAMBLY LINE LILA-020B-02_20mar17
3 PLACE mm FINISH DIMENSIONS TO BE 0.5 MICRONS (CONFIDENTIAL) ALL RIGHTS RESERVED. TRANSDUCTION OR CLEAR ANODIZE 1.0/0.5 MLL 27GA
3RD ANGLE OPPOSITE
ALL GROUND SURFACES TO BE 0.4 MICRONS. ALL O SURFACES MUST BE FINISHED EXCEPT FOR COLD COPYING WITHOUT PERMISSION OF BD IS STRICTLY
DRAWN SURFACES. FORBIDDEN. WITH OUT PAINT PROYECTION
 Stock List REV CHANGE CHK'D DATE
ITEM QTY MATERIAL FINISH DESCRIPTION
001 8 Aluminum 6061 T6 0 Cold Formed ROUGHNESS 0.8 m 3/8" x 2-1/2" x 116 mm LG 01 RELEASED A.T. 04/01/2017

001 SUPPORT BASE

60.0

44.00
9.0

4.5 5.5 -DRILL

START THRU - 2 HOLES
8.0
START

34.50
15.50

28.50
9.50
100.00

4.5 -DRILL
THRU - HOLES

103.0
113.0
START

R2.0
0.00

THIS DRAWING MAY USE BOTH INCH AND METRIC METRIC - EXCEPT AS NOTED TOLERANCES SHALL BE: ALL EDGES OF PART CONTACT SURFACES ON LOCATING UNIT No.: 02 DESIGN SOURCE DESIGNER PROJECT MGR. SYSTEM NAME SCALE SHEET RELEASE DATE
UNITS OF MEASUREMENT 1 PLACE MACHINING `0.3 BLOCKS AND FINGERS TO HAVE .12R INCH / 3.00 mm MOVIL PART
(*INDICATES INCH DIMENSIONS) 1 PLACE FABRICATION `1.5
2 PLACE `0.08 BETWEEN MACHINED SURFACES
AFTER SPOTTING.
WEIGHT (KG): N/A
FIXED PART
HOGARCIA I.SALVADOR
DESIGN SUP.
LILA NONE 2 OF 23 04/01/2017
MAXIMUM ALLOWANCE ROUGHNESS OF ALL `0.03 BETWEEN SINGLE DOWEL AND A HEEL SURFACE MARK INDENTIFICATION AND MATERIAL NUMBERS ON DETAILS. L.H. SHN DETAILER A.TORRES DESCRIPTION

DRAWING No.
SHOWN
METRIC. `0.03 BETWEEN DOWELS IN THE SAME PLANE PAINT INDENTIFICATION NUMBERS ON STRUCTURAL WORK.
BLACK OXIDE H.GARCIA CHECKER
1 PLACE mm FINISH DIMENSIONS TO BE 3.2 MICRONS
2 PLACE mm FINISH DIMENSIONS TO BE 1.6 MICRONS
`0.10 BETWEEN DOWELS IN DIFFERENT PLANES
`0.13 TO SCREW HOLES, NON ACCUMULATIVE NOTE: DRAWINGS PROPERTY OF BECKTON DICKINSON.
CUSTOMER A.TORRES LILA ASSAMBLY LINE LILA-020B-02-001
3 PLACE mm FINISH DIMENSIONS TO BE 0.5 MICRONS (CONFIDENTIAL) ALL RIGHTS RESERVED. TRANSDUCTION OR CLEAR ANODIZE 1.0/0.5 MLL 27GA
3RD ANGLE OPPOSITE
ALL GROUND SURFACES TO BE 0.4 MICRONS. ALL O SURFACES MUST BE FINISHED EXCEPT FOR COLD COPYING WITHOUT PERMISSION OF BD IS STRICTLY
DRAWN SURFACES. FORBIDDEN. WITH OUT PAINT PROYECTION
 Stock List REV CHANGE CHK'D DATE
ITEM QTY MATERIAL FINISH DESCRIPTION
002 2 Aluminum 6061 T6 0 Cold Formed ROUGHNESS 0.8 m 1/2" x 1-5/8" x 133 mm LG 01 RELEASED A.T. 04/01/2017

002_OPP 2 Aluminum 6061 T6 0 Cold Formed ROUGHNESS 0.8 m 1/2" x 1-5/8" x 133 mm LG

002 BEARING SUPPORT

130.0
2.5
DEEP

9.5

35.0

17.0
START
105.00

73.00
85.00

23.00
16.00

8.00
4.5 -DRILL 5.00 X 45.0 8.0
THRU - HOLES DEEP
A
R5.0 0.50 X 45.0
13.86
9.00

40.0 20.0 26.00 +- 0.021

0.000
5.30
25.0 21.0
8.50 START
13.86
11.70

A M3x0.5 - TAP SECTION A-A

6.0 DEEP - 3 HOLES SCALE 1 : 1

THIS DRAWING MAY USE BOTH INCH AND METRIC METRIC - EXCEPT AS NOTED TOLERANCES SHALL BE: ALL EDGES OF PART CONTACT SURFACES ON LOCATING UNIT No.: 02 DESIGN SOURCE DESIGNER PROJECT MGR. SYSTEM NAME SCALE SHEET RELEASE DATE
UNITS OF MEASUREMENT 1 PLACE MACHINING `0.3 BLOCKS AND FINGERS TO HAVE .12R INCH / 3.00 mm MOVIL PART
(*INDICATES INCH DIMENSIONS) 1 PLACE FABRICATION `1.5
2 PLACE `0.08 BETWEEN MACHINED SURFACES
AFTER SPOTTING.
WEIGHT (KG): N/A
FIXED PART
HOGARCIA I.SALVADOR
DESIGN SUP.
LILA NONE 3 OF 23 04/01/2017
MAXIMUM ALLOWANCE ROUGHNESS OF ALL `0.03 BETWEEN SINGLE DOWEL AND A HEEL SURFACE MARK INDENTIFICATION AND MATERIAL NUMBERS ON DETAILS. L.H. SHN DETAILER A.TORRES DESCRIPTION

DRAWING No.
SHOWN
METRIC. `0.03 BETWEEN DOWELS IN THE SAME PLANE PAINT INDENTIFICATION NUMBERS ON STRUCTURAL WORK.
BLACK OXIDE H.GARCIA CHECKER
1 PLACE mm FINISH DIMENSIONS TO BE 3.2 MICRONS
2 PLACE mm FINISH DIMENSIONS TO BE 1.6 MICRONS
`0.10 BETWEEN DOWELS IN DIFFERENT PLANES
`0.13 TO SCREW HOLES, NON ACCUMULATIVE NOTE: DRAWINGS PROPERTY OF BECKTON DICKINSON.
R.H. OPP CUSTOMER A.TORRES LILA ASSAMBLY LINE LILA-020B-02-002
3 PLACE mm FINISH DIMENSIONS TO BE 0.5 MICRONS (CONFIDENTIAL) ALL RIGHTS RESERVED. TRANSDUCTION OR CLEAR ANODIZE 1.0/0.5 MLL 27GA
3RD ANGLE OPPOSITE
ALL GROUND SURFACES TO BE 0.4 MICRONS. ALL O SURFACES MUST BE FINISHED EXCEPT FOR COLD COPYING WITHOUT PERMISSION OF BD IS STRICTLY
WITH OUT PAINT PROYECTION
DRAWN SURFACES. FORBIDDEN.
LILA-020B-02-002_OPP
 Stock List REV CHANGE CHK'D DATE
ITEM QTY MATERIAL FINISH DESCRIPTION
003 4 HRS ROUGHNESS 0.8 m 1-1/2" DIA x 6 mm LG 01 RELEASED A.T. 04/01/2017

003 COVER BEARING

3.0

90.00
FOR M3 - F.H.C.S.
C`SINC - AS SHOWN
3 HOLES
38.0
16.00

0.00

18.0
DRILL THRU 8.00

17.00
13.86

0.00

13.86

THIS DRAWING MAY USE BOTH INCH AND METRIC METRIC - EXCEPT AS NOTED TOLERANCES SHALL BE: ALL EDGES OF PART CONTACT SURFACES ON LOCATING UNIT No.: 02 DESIGN SOURCE DESIGNER PROJECT MGR. SYSTEM NAME SCALE SHEET RELEASE DATE
UNITS OF MEASUREMENT 1 PLACE MACHINING `0.3 BLOCKS AND FINGERS TO HAVE .12R INCH / 3.00 mm MOVIL PART
(*INDICATES INCH DIMENSIONS) 1 PLACE FABRICATION `1.5
2 PLACE `0.08 BETWEEN MACHINED SURFACES
AFTER SPOTTING.
WEIGHT (KG): N/A
FIXED PART
HOGARCIA I.SALVADOR
DESIGN SUP.
LILA NONE 4 OF 23 04/01/2017
MAXIMUM ALLOWANCE ROUGHNESS OF ALL `0.03 BETWEEN SINGLE DOWEL AND A HEEL SURFACE MARK INDENTIFICATION AND MATERIAL NUMBERS ON DETAILS. L.H. SHN DETAILER A.TORRES DESCRIPTION

DRAWING No.
SHOWN
METRIC. `0.03 BETWEEN DOWELS IN THE SAME PLANE PAINT INDENTIFICATION NUMBERS ON STRUCTURAL WORK.
BLACK OXIDE H.GARCIA CHECKER
1 PLACE mm FINISH DIMENSIONS TO BE 3.2 MICRONS
2 PLACE mm FINISH DIMENSIONS TO BE 1.6 MICRONS
`0.10 BETWEEN DOWELS IN DIFFERENT PLANES
`0.13 TO SCREW HOLES, NON ACCUMULATIVE NOTE: DRAWINGS PROPERTY OF BECKTON DICKINSON.
CUSTOMER A.TORRES LILA ASSAMBLY LINE LILA-020B-02-003
3 PLACE mm FINISH DIMENSIONS TO BE 0.5 MICRONS (CONFIDENTIAL) ALL RIGHTS RESERVED. TRANSDUCTION OR CLEAR ANODIZE 1.0/0.5 MLL 27GA
3RD ANGLE OPPOSITE
ALL GROUND SURFACES TO BE 0.4 MICRONS. ALL O SURFACES MUST BE FINISHED EXCEPT FOR COLD COPYING WITHOUT PERMISSION OF BD IS STRICTLY
DRAWN SURFACES. FORBIDDEN. WITH OUT PAINT PROYECTION
 Stock List REV CHANGE CHK'D DATE
ITEM QTY MATERIAL FINISH DESCRIPTION
004 1 Stainless Steel, 440C ROUGHNESS 0.8 m 5/8" DIA. x 176 mm LG 01 RELEASED A.T. 04/01/2017

004 SHAFT

173.0
134.3
88.8

164.00
165.10
150.50
31.50

51.50
55.90
57.00
70.50
3.50
0.00

15.00
R1.5 12.00 f7 (-- 0.016
0.034)

0.00 0.00

12.00 f7 (-- 0.016

0.034)

87.50

133.50
4.00 H7 +- 0.012
0.000 ( ) 1.0 X 45.00 Chamfer
TYP

THIS DRAWING MAY USE BOTH INCH AND METRIC METRIC - EXCEPT AS NOTED TOLERANCES SHALL BE: ALL EDGES OF PART CONTACT SURFACES ON LOCATING UNIT No.: 02 DESIGN SOURCE DESIGNER PROJECT MGR. SYSTEM NAME SCALE SHEET RELEASE DATE
UNITS OF MEASUREMENT 1 PLACE MACHINING `0.3 BLOCKS AND FINGERS TO HAVE .12R INCH / 3.00 mm MOVIL PART
(*INDICATES INCH DIMENSIONS) 1 PLACE FABRICATION `1.5
2 PLACE `0.08 BETWEEN MACHINED SURFACES
AFTER SPOTTING.
WEIGHT (KG): N/A
FIXED PART
HOGARCIA I.SALVADOR
DESIGN SUP.
LILA NONE 5 OF 23 04/01/2017
MAXIMUM ALLOWANCE ROUGHNESS OF ALL `0.03 BETWEEN SINGLE DOWEL AND A HEEL SURFACE MARK INDENTIFICATION AND MATERIAL NUMBERS ON DETAILS. L.H. SHN DETAILER A.TORRES DESCRIPTION

DRAWING No.
SHOWN
METRIC. `0.03 BETWEEN DOWELS IN THE SAME PLANE PAINT INDENTIFICATION NUMBERS ON STRUCTURAL WORK.
BLACK OXIDE H.GARCIA CHECKER
1 PLACE mm FINISH DIMENSIONS TO BE 3.2 MICRONS
2 PLACE mm FINISH DIMENSIONS TO BE 1.6 MICRONS
`0.10 BETWEEN DOWELS IN DIFFERENT PLANES
`0.13 TO SCREW HOLES, NON ACCUMULATIVE NOTE: DRAWINGS PROPERTY OF BECKTON DICKINSON.
CUSTOMER A.TORRES LILA ASSAMBLY LINE LILA-020B-02-004
3 PLACE mm FINISH DIMENSIONS TO BE 0.5 MICRONS (CONFIDENTIAL) ALL RIGHTS RESERVED. TRANSDUCTION OR CLEAR ANODIZE 1.0/0.5 MLL 27GA
3RD ANGLE OPPOSITE
ALL GROUND SURFACES TO BE 0.4 MICRONS. ALL O SURFACES MUST BE FINISHED EXCEPT FOR COLD COPYING WITHOUT PERMISSION OF BD IS STRICTLY
DRAWN SURFACES. FORBIDDEN. WITH OUT PAINT PROYECTION
 Stock List REV CHANGE CHK'D DATE
ITEM QTY MATERIAL FINISH DESCRIPTION
005 4 Stainless Steel, 440C ROUGHNESS 0.8 m 3/4" DIA. x 6 mm LG 01 RELEASED A.T. 04/01/2017

005 SPACER

3.70

18.00 12.50

THIS DRAWING MAY USE BOTH INCH AND METRIC METRIC - EXCEPT AS NOTED TOLERANCES SHALL BE: ALL EDGES OF PART CONTACT SURFACES ON LOCATING UNIT No.: 02 DESIGN SOURCE DESIGNER PROJECT MGR. SYSTEM NAME SCALE SHEET RELEASE DATE
UNITS OF MEASUREMENT 1 PLACE MACHINING `0.3 BLOCKS AND FINGERS TO HAVE .12R INCH / 3.00 mm MOVIL PART
(*INDICATES INCH DIMENSIONS) 1 PLACE FABRICATION `1.5
2 PLACE `0.08 BETWEEN MACHINED SURFACES
AFTER SPOTTING.
WEIGHT (KG): N/A
FIXED PART
HOGARCIA I.SALVADOR
DESIGN SUP.
LILA NONE 6 OF 23 04/01/2017
MAXIMUM ALLOWANCE ROUGHNESS OF ALL `0.03 BETWEEN SINGLE DOWEL AND A HEEL SURFACE MARK INDENTIFICATION AND MATERIAL NUMBERS ON DETAILS. L.H. SHN DETAILER A.TORRES DESCRIPTION

DRAWING No.
SHOWN
METRIC. `0.03 BETWEEN DOWELS IN THE SAME PLANE PAINT INDENTIFICATION NUMBERS ON STRUCTURAL WORK.
BLACK OXIDE H.GARCIA CHECKER
1 PLACE mm FINISH DIMENSIONS TO BE 3.2 MICRONS
2 PLACE mm FINISH DIMENSIONS TO BE 1.6 MICRONS
`0.10 BETWEEN DOWELS IN DIFFERENT PLANES
`0.13 TO SCREW HOLES, NON ACCUMULATIVE NOTE: DRAWINGS PROPERTY OF BECKTON DICKINSON.
CUSTOMER A.TORRES LILA ASSAMBLY LINE LILA-020B-02-005
3 PLACE mm FINISH DIMENSIONS TO BE 0.5 MICRONS (CONFIDENTIAL) ALL RIGHTS RESERVED. TRANSDUCTION OR CLEAR ANODIZE 1.0/0.5 MLL 27GA
3RD ANGLE OPPOSITE
ALL GROUND SURFACES TO BE 0.4 MICRONS. ALL O SURFACES MUST BE FINISHED EXCEPT FOR COLD COPYING WITHOUT PERMISSION OF BD IS STRICTLY
DRAWN SURFACES. FORBIDDEN. WITH OUT PAINT PROYECTION
 Stock List REV CHANGE CHK'D DATE
ITEM QTY MATERIAL FINISH DESCRIPTION
006 4 SAE 1045 ROUGHNESS 0.8 m 1/8" x 1/8" x 18 mm LG 01 RELEASED A.T. 04/01/2017

006 KEY

18.0 4.00 f8 (-- 0.01

0.03)

4.00 f8 (-- 0.01

0.03)

THIS DRAWING MAY USE BOTH INCH AND METRIC METRIC - EXCEPT AS NOTED TOLERANCES SHALL BE: ALL EDGES OF PART CONTACT SURFACES ON LOCATING UNIT No.: 02 DESIGN SOURCE DESIGNER PROJECT MGR. SYSTEM NAME SCALE SHEET RELEASE DATE
UNITS OF MEASUREMENT 1 PLACE MACHINING `0.3 BLOCKS AND FINGERS TO HAVE .12R INCH / 3.00 mm MOVIL PART
(*INDICATES INCH DIMENSIONS) 1 PLACE FABRICATION `1.5
2 PLACE `0.08 BETWEEN MACHINED SURFACES
AFTER SPOTTING.
WEIGHT (KG): N/A
FIXED PART
HOGARCIA I.SALVADOR
DESIGN SUP.
LILA NONE 7 OF 23 04/01/2017
MAXIMUM ALLOWANCE ROUGHNESS OF ALL `0.03 BETWEEN SINGLE DOWEL AND A HEEL SURFACE MARK INDENTIFICATION AND MATERIAL NUMBERS ON DETAILS. L.H. SHN DETAILER A.TORRES DESCRIPTION

DRAWING No.
SHOWN
METRIC. `0.03 BETWEEN DOWELS IN THE SAME PLANE PAINT INDENTIFICATION NUMBERS ON STRUCTURAL WORK.
BLACK OXIDE H.GARCIA CHECKER
1 PLACE mm FINISH DIMENSIONS TO BE 3.2 MICRONS
2 PLACE mm FINISH DIMENSIONS TO BE 1.6 MICRONS
`0.10 BETWEEN DOWELS IN DIFFERENT PLANES
`0.13 TO SCREW HOLES, NON ACCUMULATIVE NOTE: DRAWINGS PROPERTY OF BECKTON DICKINSON.
CUSTOMER A.TORRES LILA ASSAMBLY LINE LILA-020B-02-006
3 PLACE mm FINISH DIMENSIONS TO BE 0.5 MICRONS (CONFIDENTIAL) ALL RIGHTS RESERVED. TRANSDUCTION OR CLEAR ANODIZE 1.0/0.5 MLL 27GA
3RD ANGLE OPPOSITE
ALL GROUND SURFACES TO BE 0.4 MICRONS. ALL O SURFACES MUST BE FINISHED EXCEPT FOR COLD COPYING WITHOUT PERMISSION OF BD IS STRICTLY
DRAWN SURFACES. FORBIDDEN. WITH OUT PAINT PROYECTION
 Stock List REV CHANGE CHK'D DATE
ITEM QTY MATERIAL FINISH DESCRIPTION
007 2 Stainless Steel, 440C ROUGHNESS 0.8 m 5/8" DIA x 126 mm LG 01 RELEASED A.T. 04/01/2017

007 SHAFT

123.0
84.3
38.8

101.50

115.00
116.00
84.50
21.50

38.50
7.00
8.00
0.00
4.85

15.00

0.00 0.00

10.0

-
12.70 - 0.016 3.00 +- 0.010 - DRILL - 1.5 DEEP
0.034 0.000
2 SLOTS

THIS DRAWING MAY USE BOTH INCH AND METRIC METRIC - EXCEPT AS NOTED TOLERANCES SHALL BE: ALL EDGES OF PART CONTACT SURFACES ON LOCATING UNIT No.: 02 DESIGN SOURCE DESIGNER PROJECT MGR. SYSTEM NAME SCALE SHEET RELEASE DATE
UNITS OF MEASUREMENT 1 PLACE MACHINING `0.3 BLOCKS AND FINGERS TO HAVE .12R INCH / 3.00 mm MOVIL PART
(*INDICATES INCH DIMENSIONS) 1 PLACE FABRICATION `1.5
2 PLACE `0.08 BETWEEN MACHINED SURFACES
AFTER SPOTTING.
WEIGHT (KG): N/A
FIXED PART
HOGARCIA I.SALVADOR
DESIGN SUP.
LILA NONE 8 OF 23 04/01/2017
MAXIMUM ALLOWANCE ROUGHNESS OF ALL `0.03 BETWEEN SINGLE DOWEL AND A HEEL SURFACE MARK INDENTIFICATION AND MATERIAL NUMBERS ON DETAILS. L.H. SHN DETAILER A.TORRES DESCRIPTION

DRAWING No.
SHOWN
METRIC. `0.03 BETWEEN DOWELS IN THE SAME PLANE PAINT INDENTIFICATION NUMBERS ON STRUCTURAL WORK.
BLACK OXIDE H.GARCIA CHECKER
1 PLACE mm FINISH DIMENSIONS TO BE 3.2 MICRONS
2 PLACE mm FINISH DIMENSIONS TO BE 1.6 MICRONS
`0.10 BETWEEN DOWELS IN DIFFERENT PLANES
`0.13 TO SCREW HOLES, NON ACCUMULATIVE NOTE: DRAWINGS PROPERTY OF BECKTON DICKINSON.
CUSTOMER A.TORRES LILA ASSAMBLY LINE LILA-020B-02-007
3 PLACE mm FINISH DIMENSIONS TO BE 0.5 MICRONS (CONFIDENTIAL) ALL RIGHTS RESERVED. TRANSDUCTION OR CLEAR ANODIZE 1.0/0.5 MLL 27GA
3RD ANGLE OPPOSITE
ALL GROUND SURFACES TO BE 0.4 MICRONS. ALL O SURFACES MUST BE FINISHED EXCEPT FOR COLD COPYING WITHOUT PERMISSION OF BD IS STRICTLY
DRAWN SURFACES. FORBIDDEN. WITH OUT PAINT PROYECTION
 Stock List REV CHANGE CHK'D DATE
ITEM QTY MATERIAL FINISH DESCRIPTION
008 2 ACETAL, RESINE BLACK ROUGHNESS 0.8 m 5/8" x 1" x 943 mm LG 01 RELEASED A.T. 04/01/2017

008_OPP 2 ACETAL, RESINE BLACK ROUGHNESS 0.8 m 5/8" x 1" x 943 mm LG

008 GUIDE

217.50

435.00

652.50

870.00

890.00
11.82
7.42
5.48
25.0
8.00

12.0
START

FOR M4 - S.H.C.S.
C`BORE - AS SHOWN
5 HOLES
20.0
START

940.0
0.00

12.00

11.82
0.00
5.48
7.42
4.0
DEEP
0.00 0.00 1.30
2.30
12.50 15.00 12.50

8.00
THIS DRAWING MAY USE BOTH INCH AND METRIC METRIC - EXCEPT AS NOTED TOLERANCES SHALL BE: ALL EDGES OF PART CONTACT SURFACES ON LOCATING UNIT No.: 02 DESIGN SOURCE DESIGNER PROJECT MGR. SYSTEM NAME SCALE SHEET RELEASE DATE
UNITS OF MEASUREMENT 1 PLACE MACHINING `0.3 BLOCKS AND FINGERS TO HAVE .12R INCH / 3.00 mm MOVIL PART
(*INDICATES INCH DIMENSIONS) 1 PLACE FABRICATION `1.5
2 PLACE `0.08 BETWEEN MACHINED SURFACES
AFTER SPOTTING.
WEIGHT (KG): N/A
FIXED PART
HOGARCIA I.SALVADOR
DESIGN SUP.
LILA NONE 9 OF 23 04/01/2017
MAXIMUM ALLOWANCE ROUGHNESS OF ALL `0.03 BETWEEN SINGLE DOWEL AND A HEEL SURFACE MARK INDENTIFICATION AND MATERIAL NUMBERS ON DETAILS. L.H. SHN DETAILER A.TORRES DESCRIPTION

DRAWING No.
SHOWN
METRIC. `0.03 BETWEEN DOWELS IN THE SAME PLANE PAINT INDENTIFICATION NUMBERS ON STRUCTURAL WORK.
BLACK OXIDE H.GARCIA CHECKER
1 PLACE mm FINISH DIMENSIONS TO BE 3.2 MICRONS
2 PLACE mm FINISH DIMENSIONS TO BE 1.6 MICRONS
`0.10 BETWEEN DOWELS IN DIFFERENT PLANES
`0.13 TO SCREW HOLES, NON ACCUMULATIVE NOTE: DRAWINGS PROPERTY OF BECKTON DICKINSON.
R.H. OPP CUSTOMER A.TORRES LILA ASSAMBLY LINE LILA-020B-02-008
3 PLACE mm FINISH DIMENSIONS TO BE 0.5 MICRONS (CONFIDENTIAL) ALL RIGHTS RESERVED. TRANSDUCTION OR CLEAR ANODIZE 1.0/0.5 MLL 27GA
3RD ANGLE OPPOSITE
ALL GROUND SURFACES TO BE 0.4 MICRONS. ALL O SURFACES MUST BE FINISHED EXCEPT FOR COLD COPYING WITHOUT PERMISSION OF BD IS STRICTLY
WITH OUT PAINT PROYECTION
DRAWN SURFACES. FORBIDDEN.
LILA-020-02-008_OPP
 Stock List REV CHANGE CHK'D DATE
ITEM QTY MATERIAL FINISH DESCRIPTION
009 3 Stainless Steel, 440C ROUGHNESS 0.8 m 3/4" DIA. x 81 mm LG 01 RELEASED A.T. 04/01/2017

009 SHAFT

78.0

54.8
23.3

25.00

53.00
33.00

45.00

74.05
73.05
4.15
5.15
19.1

8.00

0.00 0.00 14.0

-
16.21 - 0.016
0.034
7.00

0.00

5.5 -DRILL
THRU - 2 HOLES

THIS DRAWING MAY USE BOTH INCH AND METRIC METRIC - EXCEPT AS NOTED TOLERANCES SHALL BE: ALL EDGES OF PART CONTACT SURFACES ON LOCATING UNIT No.: 02 DESIGN SOURCE DESIGNER PROJECT MGR. SYSTEM NAME SCALE SHEET RELEASE DATE
UNITS OF MEASUREMENT 1 PLACE MACHINING `0.3 BLOCKS AND FINGERS TO HAVE .12R INCH / 3.00 mm MOVIL PART
(*INDICATES INCH DIMENSIONS) 1 PLACE FABRICATION `1.5
2 PLACE `0.08 BETWEEN MACHINED SURFACES
AFTER SPOTTING.
WEIGHT (KG): N/A
FIXED PART
HOGARCIA I.SALVADOR
DESIGN SUP.
LILA NONE 10 OF 23 04/01/2017
MAXIMUM ALLOWANCE ROUGHNESS OF ALL `0.03 BETWEEN SINGLE DOWEL AND A HEEL SURFACE MARK INDENTIFICATION AND MATERIAL NUMBERS ON DETAILS. L.H. SHN DETAILER A.TORRES DESCRIPTION

DRAWING No.
SHOWN
METRIC. `0.03 BETWEEN DOWELS IN THE SAME PLANE PAINT INDENTIFICATION NUMBERS ON STRUCTURAL WORK.
BLACK OXIDE H.GARCIA CHECKER
1 PLACE mm FINISH DIMENSIONS TO BE 3.2 MICRONS
2 PLACE mm FINISH DIMENSIONS TO BE 1.6 MICRONS
`0.10 BETWEEN DOWELS IN DIFFERENT PLANES
`0.13 TO SCREW HOLES, NON ACCUMULATIVE NOTE: DRAWINGS PROPERTY OF BECKTON DICKINSON.
CUSTOMER A.TORRES LILA ASSAMBLY LINE LILA-020B-02-009
3 PLACE mm FINISH DIMENSIONS TO BE 0.5 MICRONS (CONFIDENTIAL) ALL RIGHTS RESERVED. TRANSDUCTION OR CLEAR ANODIZE 1.0/0.5 MLL 27GA
3RD ANGLE OPPOSITE
ALL GROUND SURFACES TO BE 0.4 MICRONS. ALL O SURFACES MUST BE FINISHED EXCEPT FOR COLD COPYING WITHOUT PERMISSION OF BD IS STRICTLY
DRAWN SURFACES. FORBIDDEN. WITH OUT PAINT PROYECTION
 Stock List REV CHANGE CHK'D DATE
ITEM QTY MATERIAL FINISH DESCRIPTION
010 2 STEEL ANGLE ROUGHNESS 0.8 m 3" x 3" x 1/2" WT.x 31.0 mm 01 RELEASED A.T. 04/01/2017

010 ADJUST ANGLE

7.0 -DRILL
THRU - 2 HOLES

12.00
28.0

8.0
START

9.0
START
26.00

12.00
0.00
25.0
CUT
5.5 - DRILL
THRU - 2 SLOTS

49.50

50.0
CUT 34.50

0.00
10.0
START

0.00
THIS DRAWING MAY USE BOTH INCH AND METRIC METRIC - EXCEPT AS NOTED TOLERANCES SHALL BE: ALL EDGES OF PART CONTACT SURFACES ON LOCATING UNIT No.: 02 DESIGN SOURCE DESIGNER PROJECT MGR. SYSTEM NAME SCALE SHEET RELEASE DATE
UNITS OF MEASUREMENT 1 PLACE MACHINING `0.3 BLOCKS AND FINGERS TO HAVE .12R INCH / 3.00 mm MOVIL PART
(*INDICATES INCH DIMENSIONS) 1 PLACE FABRICATION `1.5
2 PLACE `0.08 BETWEEN MACHINED SURFACES
AFTER SPOTTING.
WEIGHT (KG): 0.02 kg
FIXED PART
HOGARCIA I.SALVADOR
DESIGN SUP.
LILA NONE 11 OF 23 04/01/2017
MAXIMUM ALLOWANCE ROUGHNESS OF ALL `0.03 BETWEEN SINGLE DOWEL AND A HEEL SURFACE MARK INDENTIFICATION AND MATERIAL NUMBERS ON DETAILS. L.H. SHN DETAILER A.TORRES DESCRIPTION

DRAWING No.
SHOWN
METRIC. `0.03 BETWEEN DOWELS IN THE SAME PLANE PAINT INDENTIFICATION NUMBERS ON STRUCTURAL WORK.
BLACK OXIDE H.GARCIA CHECKER
1 PLACE mm FINISH DIMENSIONS TO BE 3.2 MICRONS
2 PLACE mm FINISH DIMENSIONS TO BE 1.6 MICRONS
`0.10 BETWEEN DOWELS IN DIFFERENT PLANES
`0.13 TO SCREW HOLES, NON ACCUMULATIVE NOTE: DRAWINGS PROPERTY OF BECKTON DICKINSON.
CUSTOMER A.TORRES LILA ASSAMBLY LINE LILA-020B-02-010
3 PLACE mm FINISH DIMENSIONS TO BE 0.5 MICRONS (CONFIDENTIAL) ALL RIGHTS RESERVED. TRANSDUCTION OR CLEAR ANODIZE 1.0/0.5 MLL 27GA
3RD ANGLE OPPOSITE
ALL GROUND SURFACES TO BE 0.4 MICRONS. ALL O SURFACES MUST BE FINISHED EXCEPT FOR COLD COPYING WITHOUT PERMISSION OF BD IS STRICTLY
DRAWN SURFACES. FORBIDDEN. WITH OUT PAINT PROYECTION
 Stock List REV CHANGE CHK'D DATE
ITEM QTY MATERIAL FINISH DESCRIPTION
011 1 Aluminum 6061 T6 0 Cold Formed ROUGHNESS 0.8 m 1/4" x 1" x 31 mm 01 RELEASED A.T. 04/01/2017

011 BLOCK

28.0

6.0

M5x0.8 - TAP
THRU

13.00

23.0

5.0
START 4.5 -DRILL
8.00

16.00

6.0 THRU - 2 HOLES

START

THIS DRAWING MAY USE BOTH INCH AND METRIC METRIC - EXCEPT AS NOTED TOLERANCES SHALL BE: ALL EDGES OF PART CONTACT SURFACES ON LOCATING UNIT No.: 02 DESIGN SOURCE DESIGNER PROJECT MGR. SYSTEM NAME SCALE SHEET RELEASE DATE
UNITS OF MEASUREMENT 1 PLACE MACHINING `0.3 BLOCKS AND FINGERS TO HAVE .12R INCH / 3.00 mm MOVIL PART
(*INDICATES INCH DIMENSIONS) 1 PLACE FABRICATION `1.5
2 PLACE `0.08 BETWEEN MACHINED SURFACES
AFTER SPOTTING.
WEIGHT (KG): N/A
FIXED PART
HOGARCIA I.SALVADOR
DESIGN SUP.
LILA NONE 12 OF 23 04/01/2017
MAXIMUM ALLOWANCE ROUGHNESS OF ALL `0.03 BETWEEN SINGLE DOWEL AND A HEEL SURFACE MARK INDENTIFICATION AND MATERIAL NUMBERS ON DETAILS. L.H. SHN DETAILER A.TORRES DESCRIPTION

DRAWING No.
SHOWN
METRIC. `0.03 BETWEEN DOWELS IN THE SAME PLANE PAINT INDENTIFICATION NUMBERS ON STRUCTURAL WORK.
BLACK OXIDE H.GARCIA CHECKER
1 PLACE mm FINISH DIMENSIONS TO BE 3.2 MICRONS
2 PLACE mm FINISH DIMENSIONS TO BE 1.6 MICRONS
`0.10 BETWEEN DOWELS IN DIFFERENT PLANES
`0.13 TO SCREW HOLES, NON ACCUMULATIVE NOTE: DRAWINGS PROPERTY OF BECKTON DICKINSON.
CUSTOMER A.TORRES LILA ASSAMBLY LINE LILA-020B-02-011
3 PLACE mm FINISH DIMENSIONS TO BE 0.5 MICRONS (CONFIDENTIAL) ALL RIGHTS RESERVED. TRANSDUCTION OR CLEAR ANODIZE 1.0/0.5 MLL 27GA
3RD ANGLE OPPOSITE
ALL GROUND SURFACES TO BE 0.4 MICRONS. ALL O SURFACES MUST BE FINISHED EXCEPT FOR COLD COPYING WITHOUT PERMISSION OF BD IS STRICTLY
DRAWN SURFACES. FORBIDDEN. WITH OUT PAINT PROYECTION
 Stock List REV CHANGE CHK'D DATE
ITEM QTY MATERIAL FINISH DESCRIPTION
012 424 PEEK Plastic ACETAL, RESINE BLACK 1/8" x 3/4" x 23 mm LG 01 RELEASED A.T. 04/01/2017

012 PLATE

17.0

3.00

4.76

12.26
2.74
R1.0

8.91
90.00
20.0 3.3 - DRILL
THRU - 2 HOLES

5.0 3.0 X 45.00 Chamfer

START
9.53

3.7
START
THIS DRAWING MAY USE BOTH INCH AND METRIC METRIC - EXCEPT AS NOTED TOLERANCES SHALL BE: ALL EDGES OF PART CONTACT SURFACES ON LOCATING UNIT No.: 02 DESIGN SOURCE DESIGNER PROJECT MGR. SYSTEM NAME SCALE SHEET RELEASE DATE
UNITS OF MEASUREMENT 1 PLACE MACHINING `0.3 BLOCKS AND FINGERS TO HAVE .12R INCH / 3.00 mm MOVIL PART
(*INDICATES INCH DIMENSIONS) 1 PLACE FABRICATION `1.5
2 PLACE `0.08 BETWEEN MACHINED SURFACES
AFTER SPOTTING.
WEIGHT (KG): N/A
FIXED PART
HOGARCIA I.SALVADOR
DESIGN SUP.
LILA NONE 13 OF 23 04/01/2017
MAXIMUM ALLOWANCE ROUGHNESS OF ALL `0.03 BETWEEN SINGLE DOWEL AND A HEEL SURFACE MARK INDENTIFICATION AND MATERIAL NUMBERS ON DETAILS. L.H. SHN DETAILER A.TORRES DESCRIPTION

DRAWING No.
SHOWN
METRIC. `0.03 BETWEEN DOWELS IN THE SAME PLANE PAINT INDENTIFICATION NUMBERS ON STRUCTURAL WORK.
BLACK OXIDE H.GARCIA CHECKER
1 PLACE mm FINISH DIMENSIONS TO BE 3.2 MICRONS
2 PLACE mm FINISH DIMENSIONS TO BE 1.6 MICRONS
`0.10 BETWEEN DOWELS IN DIFFERENT PLANES
`0.13 TO SCREW HOLES, NON ACCUMULATIVE NOTE: DRAWINGS PROPERTY OF BECKTON DICKINSON.
CUSTOMER A.TORRES LILA ASSAMBLY LINE LILA-020B-02-012
3 PLACE mm FINISH DIMENSIONS TO BE 0.5 MICRONS (CONFIDENTIAL) ALL RIGHTS RESERVED. TRANSDUCTION OR CLEAR ANODIZE 1.0/0.5 MLL 27GA
3RD ANGLE OPPOSITE
ALL GROUND SURFACES TO BE 0.4 MICRONS. ALL O SURFACES MUST BE FINISHED EXCEPT FOR COLD COPYING WITHOUT PERMISSION OF BD IS STRICTLY
DRAWN SURFACES. FORBIDDEN. WITH OUT PAINT PROYECTION
 Stock List REV CHANGE CHK'D DATE
ITEM QTY MATERIAL FINISH DESCRIPTION
013 2 STEEL ANGLE ROUGHNESS 0.8 m 1" x 1" x 1/8" WT x 25.0 mm 01 RELEASED A.T. 04/01/2017

013 ANGLE

4.5 -DRILL
THRU - 2 HOLES

10.00

5.0
START
12.9
START

20.0

1.00

9.00
25.4

3.175
STK M3x0.5 - TAP
THRU - 2 HOLES

19.00

25.4

0.00
3.175
STK
CLEAN FACES

THIS DRAWING MAY USE BOTH INCH AND METRIC METRIC - EXCEPT AS NOTED TOLERANCES SHALL BE: ALL EDGES OF PART CONTACT SURFACES ON LOCATING UNIT No.: 02 0.00 DESIGN SOURCE DESIGNER PROJECT MGR. SYSTEM NAME SCALE SHEET RELEASE DATE
UNITS OF MEASUREMENT 1 PLACE MACHINING `0.3 BLOCKS AND FINGERS TO HAVE .12R INCH / 3.00 mm MOVIL PART
(*INDICATES INCH DIMENSIONS) 1 PLACE FABRICATION `1.5
2 PLACE `0.08 BETWEEN MACHINED SURFACES
AFTER SPOTTING.
WEIGHT (KG): N/A
FIXED PART
HOGARCIA I.SALVADOR
DESIGN SUP.
LILA NONE 14 OF 23 04/01/2017
MAXIMUM ALLOWANCE ROUGHNESS OF ALL `0.03 BETWEEN SINGLE DOWEL AND A HEEL SURFACE MARK INDENTIFICATION AND MATERIAL NUMBERS ON DETAILS. L.H. SHN DETAILER A.TORRES DESCRIPTION

DRAWING No.
SHOWN
METRIC. `0.03 BETWEEN DOWELS IN THE SAME PLANE PAINT INDENTIFICATION NUMBERS ON STRUCTURAL WORK.
BLACK OXIDE H.GARCIA CHECKER
1 PLACE mm FINISH DIMENSIONS TO BE 3.2 MICRONS
2 PLACE mm FINISH DIMENSIONS TO BE 1.6 MICRONS
`0.10 BETWEEN DOWELS IN DIFFERENT PLANES
`0.13 TO SCREW HOLES, NON ACCUMULATIVE NOTE: DRAWINGS PROPERTY OF BECKTON DICKINSON.
CUSTOMER A.TORRES LILA ASSAMBLY LINE LILA-020B-02-013
3 PLACE mm FINISH DIMENSIONS TO BE 0.5 MICRONS (CONFIDENTIAL) ALL RIGHTS RESERVED. TRANSDUCTION OR CLEAR ANODIZE 1.0/0.5 MLL 27GA
3RD ANGLE OPPOSITE
ALL GROUND SURFACES TO BE 0.4 MICRONS. ALL O SURFACES MUST BE FINISHED EXCEPT FOR COLD COPYING WITHOUT PERMISSION OF BD IS STRICTLY
DRAWN SURFACES. FORBIDDEN. WITH OUT PAINT PROYECTION
 Stock List REV CHANGE CHK'D DATE
ITEM QTY MATERIAL DESCRIPTION
014 2 PEEK 3/8" X 1/4" X 769.0 mm LG. 01 RELEASED A.T. 04/01/2017

014 GUIDE

10.00 3.0
TYP T 6.0

10.9
9.5 T
STK
REF

R1.0 3.0 SECTION T-T

TYP SCALE 1 : 1
768.4
REF
4.5

FOR M3 THRU 562.0 55.0

6.5 3.0
2-HOLES

THIS DRAWING MAY USE BOTH INCH AND METRIC METRIC - EXCEPT AS NOTED TOLERANCES SHALL BE: ALL EDGES OF PART CONTACT SURFACES ON LOCATING UNIT No.: 02 DESIGN SOURCE DESIGNER PROJECT MGR. SYSTEM NAME SCALE SHEET RELEASE DATE
UNITS OF MEASUREMENT 1 PLACE MACHINING `0.3 BLOCKS AND FINGERS TO HAVE .12R INCH / 3.00 mm MOVIL PART
(*INDICATES INCH DIMENSIONS) 1 PLACE FABRICATION `1.5
2 PLACE `0.08 BETWEEN MACHINED SURFACES
AFTER SPOTTING.
WEIGHT (KG): N/A
FIXED PART
HOGARCIA I.SALVADOR
DESIGN SUP.
LILA NONE 15 OF 23 04/01/2017
MAXIMUM ALLOWANCE ROUGHNESS OF ALL `0.03 BETWEEN SINGLE DOWEL AND A HEEL SURFACE MARK INDENTIFICATION AND MATERIAL NUMBERS ON DETAILS. DETAILER A.TORRES DESCRIPTION

DRAWING No.
SHOWN
METRIC. `0.03 BETWEEN DOWELS IN THE SAME PLANE PAINT INDENTIFICATION NUMBERS ON STRUCTURAL WORK.
BLACK OXIDE H.GARCIA CHECKER
1 PLACE mm FINISH DIMENSIONS TO BE 3.2 MICRONS
2 PLACE mm FINISH DIMENSIONS TO BE 1.6 MICRONS
`0.10 BETWEEN DOWELS IN DIFFERENT PLANES
`0.13 TO SCREW HOLES, NON ACCUMULATIVE NOTE: DRAWINGS PROPERTY OF BECKTON DICKINSON.
CUSTOMER A.TORRES LILA ASSAMBLY LINE LILA-020B-02-014
3 PLACE mm FINISH DIMENSIONS TO BE 0.5 MICRONS (CONFIDENTIAL) ALL RIGHTS RESERVED. TRANSDUCTION OR CLEAR ANODIZE 1.0/0.5 MLL 27GA
3RD ANGLE OPPOSITE
ALL GROUND SURFACES TO BE 0.4 MICRONS. ALL O SURFACES MUST BE FINISHED EXCEPT FOR COLD COPYING WITHOUT PERMISSION OF BD IS STRICTLY
DRAWN SURFACES. FORBIDDEN. WITH OUT PAINT PROYECTION
 Stock List REV CHANGE CHK'D DATE
ITEM QTY MATERIAL DESCRIPTION
015 2 HRS 1/2" X 3 1/2" X 3 1/2" X 85.0 mm LG. 01 RELEASED A.T. 04/01/2017
37.0

015 SUPPORT
6.00

8.00

4.0
4.0 3.5
2-SLOT

R3.0 8.00
17.0 TYP
M3x0.5 - 6H 6.0
1-HOLE

12.0

36.0

27.00

3.0
STK

16.0
STK
37.0

THIS DRAWING MAY USE BOTH INCH AND METRIC METRIC - EXCEPT AS NOTED TOLERANCES SHALL BE: ALL EDGES OF PART CONTACT SURFACES ON LOCATING UNIT No.: 02 DESIGN SOURCE DESIGNER PROJECT MGR. SYSTEM NAME SCALE SHEET RELEASE DATE
UNITS OF MEASUREMENT 1 PLACE MACHINING `0.3 BLOCKS AND FINGERS TO HAVE .12R INCH / 3.00 mm MOVIL PART
(*INDICATES INCH DIMENSIONS) 1 PLACE FABRICATION `1.5
2 PLACE `0.08 BETWEEN MACHINED SURFACES
AFTER SPOTTING.
WEIGHT (KG): 0.03 kg
FIXED PART
HOGARCIA I.SALVADOR
DESIGN SUP.
LILA NONE 16 OF 23 04/01/2017
MAXIMUM ALLOWANCE ROUGHNESS OF ALL `0.03 BETWEEN SINGLE DOWEL AND A HEEL SURFACE MARK INDENTIFICATION AND MATERIAL NUMBERS ON DETAILS. DETAILER A.TORRES DESCRIPTION

DRAWING No.
SHOWN
METRIC. `0.03 BETWEEN DOWELS IN THE SAME PLANE PAINT INDENTIFICATION NUMBERS ON STRUCTURAL WORK.
BLACK OXIDE H.GARCIA CHECKER
1 PLACE mm FINISH DIMENSIONS TO BE 3.2 MICRONS
2 PLACE mm FINISH DIMENSIONS TO BE 1.6 MICRONS
`0.10 BETWEEN DOWELS IN DIFFERENT PLANES
`0.13 TO SCREW HOLES, NON ACCUMULATIVE NOTE: DRAWINGS PROPERTY OF BECKTON DICKINSON.
CUSTOMER A.TORRES LILA ASSAMBLY LINE LILA-020B-02-015
3 PLACE mm FINISH DIMENSIONS TO BE 0.5 MICRONS (CONFIDENTIAL) ALL RIGHTS RESERVED. TRANSDUCTION OR CLEAR ANODIZE 1.0/0.5 MLL 27GA
3RD ANGLE OPPOSITE
ALL GROUND SURFACES TO BE 0.4 MICRONS. ALL O SURFACES MUST BE FINISHED EXCEPT FOR COLD COPYING WITHOUT PERMISSION OF BD IS STRICTLY
DRAWN SURFACES. FORBIDDEN. WITH OUT PAINT PROYECTION
 Stock List REV CHANGE CHK'D DATE
ITEM QTY MATERIAL DESCRIPTION
016 2 HRS 1/4" X 3/4" X 80.0 mm LG 01 RELEASED A.T. 04/01/2017

016 SUPPORT
16.00

32.00 0.00

6.00

14.00

8 - DRILL - THRU
2 - SLOTS
4.00
0.00
4.00

15.00
0.00
16.00 M3x0.5 - 6H 6.0
17.00
8.00 M3x0.5 - TAP x 6.0 DEEP START
START
FAR SIDE
6.00
9.00
START 12.00
0.00 0.00

36.00 3.00

R3.00
TYP
3.00
24.00
27.00
R6.00
TYP

THIS DRAWING MAY USE BOTH INCH AND METRIC METRIC - EXCEPT AS NOTED TOLERANCES SHALL BE: ALL EDGES OF PART CONTACT SURFACES ON LOCATING UNIT No.: DESIGN SOURCE DESIGNER PROJECT MGR. SYSTEM NAME SCALE SHEET RELEASE DATE
UNITS OF MEASUREMENT 1 PLACE MACHINING `0.3 BLOCKS AND FINGERS TO HAVE .12R INCH / 3.00 mm MOVIL PART
(*INDICATES INCH DIMENSIONS) 1 PLACE FABRICATION `1.5
2 PLACE `0.08 BETWEEN MACHINED SURFACES
AFTER SPOTTING.
WEIGHT (KG): 0.02 kg
FIXED PART
HOGARCIA I.SALVADOR
DESIGN SUP.
LILA NONE 17 OF 23 04/01/2017
MAXIMUM ALLOWANCE ROUGHNESS OF ALL `0.03 BETWEEN SINGLE DOWEL AND A HEEL SURFACE MARK INDENTIFICATION AND MATERIAL NUMBERS ON DETAILS. DETAILER A.TORRES DESCRIPTION

DRAWING No.
SHOWN
METRIC. `0.03 BETWEEN DOWELS IN THE SAME PLANE PAINT INDENTIFICATION NUMBERS ON STRUCTURAL WORK.
BLACK OXIDE H.GARCIA CHECKER
1 PLACE mm FINISH DIMENSIONS TO BE 3.2 MICRONS
2 PLACE mm FINISH DIMENSIONS TO BE 1.6 MICRONS
`0.10 BETWEEN DOWELS IN DIFFERENT PLANES
`0.13 TO SCREW HOLES, NON ACCUMULATIVE NOTE: DRAWINGS PROPERTY OF BECKTON DICKINSON.
CUSTOMER A.TORRES LILA ASSAMBLY LINE LILA-020B-02-016
3 PLACE mm FINISH DIMENSIONS TO BE 0.5 MICRONS (CONFIDENTIAL) ALL RIGHTS RESERVED. TRANSDUCTION OR CLEAR ANODIZE 1.0/0.5 MLL 27GA
3RD ANGLE OPPOSITE
ALL GROUND SURFACES TO BE 0.4 MICRONS. ALL O SURFACES MUST BE FINISHED EXCEPT FOR COLD COPYING WITHOUT PERMISSION OF BD IS STRICTLY
DRAWN SURFACES. FORBIDDEN. WITH OUT PAINT PROYECTION
 Stock List REV CHANGE CHK'D DATE
ITEM QTY MATERIAL DESCRIPTION
1 1 HRS 3/16" X 2 1/8" X 53.0 mm LG 01 RELEASED A.T. 04/01/2017

017 SPACER

1.50
0.5 X 45.00
53.00 CHAMFER TYP

90.0
TYP

90.0
TYP

16.00
TYP

53.00

OR M3 FHCS
C`BORE AS SHOWN
20.00 4 HOLES

1.00
DEEP

THIS DRAWING MAY USE BOTH INCH AND METRIC METRIC - EXCEPT AS NOTED TOLERANCES SHALL BE: ALL EDGES OF PART CONTACT SURFACES ON LOCATING UNIT No.: DESIGN SOURCE DESIGNER PROJECT MGR. SYSTEM NAME SCALE SHEET RELEASE DATE
UNITS OF MEASUREMENT 1 PLACE MACHINING `0.3 BLOCKS AND FINGERS TO HAVE .12R INCH / 3.00 mm MOVIL PART
(*INDICATES INCH DIMENSIONS) 1 PLACE FABRICATION `1.5
2 PLACE `0.08 BETWEEN MACHINED SURFACES
AFTER SPOTTING.
WEIGHT (KG): N/A
FIXED PART
HOGARCIA I.SALVADOR
DESIGN SUP.
LILA NONE 18 OF 23 04/01/2017
MAXIMUM ALLOWANCE ROUGHNESS OF ALL `0.03 BETWEEN SINGLE DOWEL AND A HEEL SURFACE MARK INDENTIFICATION AND MATERIAL NUMBERS ON DETAILS. DETAILER A.TORRES DESCRIPTION

DRAWING No.
SHOWN
METRIC. `0.03 BETWEEN DOWELS IN THE SAME PLANE PAINT INDENTIFICATION NUMBERS ON STRUCTURAL WORK.
BLACK OXIDE H.GARCIA CHECKER
1 PLACE mm FINISH DIMENSIONS TO BE 3.2 MICRONS
2 PLACE mm FINISH DIMENSIONS TO BE 1.6 MICRONS
`0.10 BETWEEN DOWELS IN DIFFERENT PLANES
`0.13 TO SCREW HOLES, NON ACCUMULATIVE NOTE: DRAWINGS PROPERTY OF BECKTON DICKINSON.
CUSTOMER A.TORRES LILA ASSAMBLY LINE LILA-020B-02-017
3 PLACE mm FINISH DIMENSIONS TO BE 0.5 MICRONS (CONFIDENTIAL) ALL RIGHTS RESERVED. TRANSDUCTION OR CLEAR ANODIZE 1.0/0.5 MLL 27GA
3RD ANGLE OPPOSITE
ALL GROUND SURFACES TO BE 0.4 MICRONS. ALL O SURFACES MUST BE FINISHED EXCEPT FOR COLD COPYING WITHOUT PERMISSION OF BD IS STRICTLY
DRAWN SURFACES. FORBIDDEN. WITH OUT PAINT PROYECTION
 Stock List REV CHANGE CHK'D DATE

10.00 ITEM QTY MATERIAL DESCRIPTION

018 1 HRS 8" X 8" X 5/8" X 50.0 mm LG 01 RELEASED A.T. 04/01/2017
START

018 ANGLE
15.00
START 50.00
0.00

9.0 RILL - THRU

0.00

40.00
2 HOLES

10.0 X 45.00
CHAMFER TYP 60.0 37.00 13.00
CUT
160.00

147.00

108.75

22.0 DRILL - THRU

1 HOLE 147.00
160.0 CUT
70.50

M10x1.5 - AP
THRU - 2 HOLES
R5.00

13.00

0.00 0.00

0.00

35.00
0.00

20.00

THIS DRAWING MAY USE BOTH INCH AND METRIC METRIC - EXCEPT AS NOTED TOLERANCES SHALL BE: ALL EDGES OF PART CONTACT SURFACES ON LOCATING UNIT No.: DESIGN SOURCE DESIGNER PROJECT MGR. SYSTEM NAME SCALE SHEET RELEASE DATE
UNITS OF MEASUREMENT 1 PLACE MACHINING `0.3 BLOCKS AND FINGERS TO HAVE .12R INCH / 3.00 mm MOVIL PART
(*INDICATES INCH DIMENSIONS) 1 PLACE FABRICATION `1.5
2 PLACE `0.08 BETWEEN MACHINED SURFACES
AFTER SPOTTING.
WEIGHT (KG): N/A
FIXED PART
HOGARCIA I.SALVADOR
DESIGN SUP.
LILA NONE 19 OF 23 04/01/2017
MAXIMUM ALLOWANCE ROUGHNESS OF ALL `0.03 BETWEEN SINGLE DOWEL AND A HEEL SURFACE MARK INDENTIFICATION AND MATERIAL NUMBERS ON DETAILS. DETAILER A.TORRES DESCRIPTION

DRAWING No.
SHOWN
METRIC. `0.03 BETWEEN DOWELS IN THE SAME PLANE PAINT INDENTIFICATION NUMBERS ON STRUCTURAL WORK.
BLACK OXIDE H.GARCIA CHECKER
1 PLACE mm FINISH DIMENSIONS TO BE 3.2 MICRONS
2 PLACE mm FINISH DIMENSIONS TO BE 1.6 MICRONS
`0.10 BETWEEN DOWELS IN DIFFERENT PLANES
`0.13 TO SCREW HOLES, NON ACCUMULATIVE NOTE: DRAWINGS PROPERTY OF BECKTON DICKINSON.
CUSTOMER A.TORRES LILA ASSAMBLY LINE LILA-020B-02-018
3 PLACE mm FINISH DIMENSIONS TO BE 0.5 MICRONS (CONFIDENTIAL) ALL RIGHTS RESERVED. TRANSDUCTION OR CLEAR ANODIZE 1.0/0.5 MLL 27GA
3RD ANGLE OPPOSITE
ALL GROUND SURFACES TO BE 0.4 MICRONS. ALL O SURFACES MUST BE FINISHED EXCEPT FOR COLD COPYING WITHOUT PERMISSION OF BD IS STRICTLY
DRAWN SURFACES. FORBIDDEN. WITH OUT PAINT PROYECTION
 Stock List REV CHANGE CHK'D DATE
ITEM QTY MATERIAL DESCRIPTION
019 TOOTHED PULEEY 23.0 019 1 AT10-16 (POLYTECH DESIGN) PURCHASED ITEM MODIFIED 01 RELEASED A.T. 04/01/2017

6.50 15.0
M2x0.4 - TAP - THRU P
4 HOLES
4.00 +- 0.02
0.00

0.5 X 45

M3x0.5 - 6H 6.0
7.7
A A
49.45

3.50

P
SECTION P-P 32.00
SCALE 1 : 0.5
20.00 g6 (-- 0.007
0.020)

23.00 SECTION A-A

SCALE 1 : 0.5

(
12.00 H7 +- 0.018
0.000 )
THIS DRAWING MAY USE BOTH INCH AND METRIC METRIC - EXCEPT AS NOTED TOLERANCES SHALL BE: ALL EDGES OF PART CONTACT SURFACES ON LOCATING UNIT No.: DESIGN SOURCE DESIGNER PROJECT MGR. SYSTEM NAME SCALE SHEET RELEASE DATE
UNITS OF MEASUREMENT 1 PLACE MACHINING `0.3 BLOCKS AND FINGERS TO HAVE .12R INCH / 3.00 mm MOVIL PART
(*INDICATES INCH DIMENSIONS) 1 PLACE FABRICATION `1.5
2 PLACE `0.08 BETWEEN MACHINED SURFACES
AFTER SPOTTING.
WEIGHT (KG): N/A
FIXED PART
I.SALVADOR
DESIGN SUP.
LILA NONE 20 OF 23 04/01/2017
MAXIMUM ALLOWANCE ROUGHNESS OF ALL `0.03 BETWEEN SINGLE DOWEL AND A HEEL SURFACE MARK INDENTIFICATION AND MATERIAL NUMBERS ON DETAILS. DETAILER A.TORRES DESCRIPTION

DRAWING No.
SHOWN
METRIC. `0.03 BETWEEN DOWELS IN THE SAME PLANE PAINT INDENTIFICATION NUMBERS ON STRUCTURAL WORK.
BLACK OXIDE CHECKER
1 PLACE mm FINISH DIMENSIONS TO BE 3.2 MICRONS
2 PLACE mm FINISH DIMENSIONS TO BE 1.6 MICRONS
`0.10 BETWEEN DOWELS IN DIFFERENT PLANES
`0.13 TO SCREW HOLES, NON ACCUMULATIVE NOTE: DRAWINGS PROPERTY OF BECKTON DICKINSON.
CUSTOMER H.GARCIA
A.TORRES LILA ASSAMBLY LINE LILA-020B-02-019_
3 PLACE mm FINISH DIMENSIONS TO BE 0.5 MICRONS (CONFIDENTIAL) ALL RIGHTS RESERVED. TRANSDUCTION OR CLEAR ANODIZE 1.0/0.5 MLL 27GA
3RD ANGLE OPPOSITE
ALL GROUND SURFACES TO BE 0.4 MICRONS. ALL O SURFACES MUST BE FINISHED EXCEPT FOR COLD COPYING WITHOUT PERMISSION OF BD IS STRICTLY
WITH OUT PAINT PROYECTION
DRAWN SURFACES. FORBIDDEN.
LILA-020B-02-019
 Stock List REV CHANGE CHK'D DATE

35.0 ITEM QTY MATERIAL DESCRIPTION

020 1 HRS 1/2" X 1 1/2" X 1 1/2" 28.0 mm LG 01 RELEASED A.T. 04/01/2017

0.00
7.0 DRILL - THRU
020 ANGLE
2 HOLES

12.00

28.0
0.00 0.00

8.0
START 28.0
9.0

12.00
0.00
START
25.0
CUT

59.50

44.50
60.0
CUT 5.5 - DRILL
70.0 THRU - 2 SLOTS

R3.0

0.00
10.0
START
26.00

0.00

THIS DRAWING MAY USE BOTH INCH AND METRIC METRIC - EXCEPT AS NOTED TOLERANCES SHALL BE: ALL EDGES OF PART CONTACT SURFACES ON LOCATING UNIT No.: DESIGN SOURCE DESIGNER PROJECT MGR. SYSTEM NAME SCALE SHEET RELEASE DATE
UNITS OF MEASUREMENT 1 PLACE MACHINING `0.3 BLOCKS AND FINGERS TO HAVE .12R INCH / 3.00 mm MOVIL PART
(*INDICATES INCH DIMENSIONS) 1 PLACE FABRICATION `1.5
2 PLACE `0.08 BETWEEN MACHINED SURFACES
AFTER SPOTTING.
WEIGHT (KG): N/A
FIXED PART
HOGARCIA I.SALVADOR
DESIGN SUP.
LILA NONE 21 OF 23 04/01/2017
MAXIMUM ALLOWANCE ROUGHNESS OF ALL `0.03 BETWEEN SINGLE DOWEL AND A HEEL SURFACE MARK INDENTIFICATION AND MATERIAL NUMBERS ON DETAILS. DETAILER A.TORRES DESCRIPTION

DRAWING No.
SHOWN
METRIC. `0.03 BETWEEN DOWELS IN THE SAME PLANE PAINT INDENTIFICATION NUMBERS ON STRUCTURAL WORK.
BLACK OXIDE H.GARCIA CHECKER
1 PLACE mm FINISH DIMENSIONS TO BE 3.2 MICRONS
2 PLACE mm FINISH DIMENSIONS TO BE 1.6 MICRONS
`0.10 BETWEEN DOWELS IN DIFFERENT PLANES
`0.13 TO SCREW HOLES, NON ACCUMULATIVE NOTE: DRAWINGS PROPERTY OF BECKTON DICKINSON.
CUSTOMER A.TORRES LILA ASSAMBLY LINE LILA-020B-02-020
3 PLACE mm FINISH DIMENSIONS TO BE 0.5 MICRONS (CONFIDENTIAL) ALL RIGHTS RESERVED. TRANSDUCTION OR CLEAR ANODIZE 1.0/0.5 MLL 27GA
3RD ANGLE OPPOSITE
ALL GROUND SURFACES TO BE 0.4 MICRONS. ALL O SURFACES MUST BE FINISHED EXCEPT FOR COLD COPYING WITHOUT PERMISSION OF BD IS STRICTLY
DRAWN SURFACES. FORBIDDEN. WITH OUT PAINT PROYECTION
 Stock List REV CHANGE CHK'D DATE
ITEM QTY MATERIAL DESCRIPTION
021 2 HRS 3/16" X 1 1/8" X 1/8" X 20.0 mm LG 01 RELEASED A.T. 04/01/2017
20.0
021 ANGLE

0.00

8.00
M3x0.5 TAP
6.0 THRU- 2 HOLES
START

9.4
START
0.00
25.4

16.00

0.00
1.00
0.00

9.00

0.00 0.00
3.18

12.50 R3.3
25.4
22.2
CUT

4.5 DRILL - THRU

2 HOLES

22.2
20.0 CUT

THIS DRAWING MAY USE BOTH INCH AND METRIC METRIC - EXCEPT AS NOTED TOLERANCES SHALL BE: ALL EDGES OF PART CONTACT SURFACES ON LOCATING UNIT No.: DESIGN SOURCE DESIGNER PROJECT MGR. SYSTEM NAME SCALE SHEET RELEASE DATE
UNITS OF MEASUREMENT 1 PLACE MACHINING `0.3 BLOCKS AND FINGERS TO HAVE .12R INCH / 3.00 mm MOVIL PART
(*INDICATES INCH DIMENSIONS) 1 PLACE FABRICATION `1.5
2 PLACE `0.08 BETWEEN MACHINED SURFACES
AFTER SPOTTING.
WEIGHT (KG): N/A
FIXED PART
HOGARCIA I.SALVADOR
DESIGN SUP.
LILA NONE 22 OF 23 04/01/2017
MAXIMUM ALLOWANCE ROUGHNESS OF ALL `0.03 BETWEEN SINGLE DOWEL AND A HEEL SURFACE MARK INDENTIFICATION AND MATERIAL NUMBERS ON DETAILS. DETAILER A.TORRES DESCRIPTION

DRAWING No.
SHOWN
METRIC. `0.03 BETWEEN DOWELS IN THE SAME PLANE PAINT INDENTIFICATION NUMBERS ON STRUCTURAL WORK.
BLACK OXIDE H.GARCIA CHECKER
1 PLACE mm FINISH DIMENSIONS TO BE 3.2 MICRONS
2 PLACE mm FINISH DIMENSIONS TO BE 1.6 MICRONS
`0.10 BETWEEN DOWELS IN DIFFERENT PLANES
`0.13 TO SCREW HOLES, NON ACCUMULATIVE NOTE: DRAWINGS PROPERTY OF BECKTON DICKINSON.
CUSTOMER A.TORRES LILA ASSAMBLY LINE LILA-020B-02-021
3 PLACE mm FINISH DIMENSIONS TO BE 0.5 MICRONS (CONFIDENTIAL) ALL RIGHTS RESERVED. TRANSDUCTION OR CLEAR ANODIZE 1.0/0.5 MLL 27GA
3RD ANGLE OPPOSITE
ALL GROUND SURFACES TO BE 0.4 MICRONS. ALL O SURFACES MUST BE FINISHED EXCEPT FOR COLD COPYING WITHOUT PERMISSION OF BD IS STRICTLY
DRAWN SURFACES. FORBIDDEN. WITH OUT PAINT PROYECTION
 Stock List REV CHANGE CHK'D DATE
ITEM QTY MATERIAL FINISH DESCRIPTION
022 3 Aluminum 6061 T6 0 Cold Formed ROUGHNESS 0.8 m 1/4" x 4" x 105.0 mm 01 RELEASED A.T. 04/01/2017

022 PLATE

32.50

65.00
0.00
4.3 - DRILL
THRU - 6 HOLES

22.0 68.00

46.50

90.0 34.0 22.0

R5.0 21.50

22.0 0.00

11.0
2.0 X 45.00 Chamfer
START

12.5
START

6.00
90.0

THIS DRAWING MAY USE BOTH INCH AND METRIC METRIC - EXCEPT AS NOTED TOLERANCES SHALL BE: ALL EDGES OF PART CONTACT SURFACES ON LOCATING UNIT No.: 02 DESIGN SOURCE DESIGNER PROJECT MGR. SYSTEM NAME SCALE SHEET RELEASE DATE
UNITS OF MEASUREMENT 1 PLACE MACHINING `0.3 BLOCKS AND FINGERS TO HAVE .12R INCH / 3.00 mm MOVIL PART
(*INDICATES INCH DIMENSIONS) 1 PLACE FABRICATION `1.5
2 PLACE `0.08 BETWEEN MACHINED SURFACES
AFTER SPOTTING.
WEIGHT (KG): 0.08 kg
FIXED PART
A.TORRES I.SALVADOR
DESIGN SUP.
LILA NONE 23 OF 23 04/01/2017
MAXIMUM ALLOWANCE ROUGHNESS OF ALL `0.03 BETWEEN SINGLE DOWEL AND A HEEL SURFACE MARK INDENTIFICATION AND MATERIAL NUMBERS ON DETAILS. DETAILER A.TORRES DESCRIPTION

DRAWING No.
SHOWN
METRIC. `0.03 BETWEEN DOWELS IN THE SAME PLANE PAINT INDENTIFICATION NUMBERS ON STRUCTURAL WORK.
BLACK OXIDE H.GARCIA CHECKER
1 PLACE mm FINISH DIMENSIONS TO BE 3.2 MICRONS
2 PLACE mm FINISH DIMENSIONS TO BE 1.6 MICRONS
`0.10 BETWEEN DOWELS IN DIFFERENT PLANES
`0.13 TO SCREW HOLES, NON ACCUMULATIVE NOTE: DRAWINGS PROPERTY OF BECKTON DICKINSON.
CUSTOMER A.TORRES LILA ASSAMBLY LINE LILA-020B-02-022
3 PLACE mm FINISH DIMENSIONS TO BE 0.5 MICRONS (CONFIDENTIAL) ALL RIGHTS RESERVED. TRANSDUCTION OR CLEAR ANODIZE 1.0/0.5 MLL 27GA
3RD ANGLE OPPOSITE
ALL GROUND SURFACES TO BE 0.4 MICRONS. ALL O SURFACES MUST BE FINISHED EXCEPT FOR COLD COPYING WITHOUT PERMISSION OF BD IS STRICTLY
DRAWN SURFACES. FORBIDDEN. WITH OUT PAINT PROYECTION