DSEPower ®

DSE9476 SPECIFICATIONS

INTELLIGENT BATTERY CHARGER AC SUPPLY

VOLTAGE RANGE
95 V to 305 V (L-N)
24 V 20 AMP FREQUENCY RANGE
47 Hz to 63 Hz (L-N)

DC OUTPUT
DSE9476 OUTPUT
20 A DC at 24 V DC

RIPPLE AND NOISE

1%

EFFICIENCY (At Full Load)

>92%

REGULATION
LINE
<0.5%

LOAD
1%

TEMPERATURE SENSOR INPUT

PT1000

PROTECTIONS
Short Circuit
DC Under & Over Voltage
DC Over Current
Reverse Polarity
Over Temperature
AC Under & Over Voltage

CHARGE FAILURE RELAY

ADVANCED FEATURES • Output short circuit and reverse KEY BENEFITS 3 A 30 V DC volt free relay
• Intelligent two, three and four stage polarity with auto recovery • Fully flexible to maximise the life of
DIMENSIONS
charging profiles for different • Automatic power de-rating at high the battery OVERALL
battery chemistries ambient temperatures • Suitable for a wide range of battery 183 mm x 233 mm x 76 mm
• Adjustable current limit (maximum • Optional battery temperature types 7.2” x 9.2” x 3.0”
20 A) compensation using PT1000 • Switched mode design WEIGHT
• Can be used as a battery charger, temperature sensor • Fault output 1.8 kg
power supply or both at the same • Active power factor correction, 0.99 • 94.5% effiency at high line, full load
OPERATING TEMPERATURE RANGE
time at full load (low line) • No external intervention for boost
-30 ºC to +80 ºC
• Automatic or manual boost and Automatic Boost Mode mode -22 °F to +176 °F
storage charge functions to help • Boosts and equalises cell charge • Multiple chargers can be linked
maintain battery condition improving battery performance together to provide larger current STORAGE TEMPERATURE RANGE
-40 ºC to +85 ºC
• Digital microprocessor technology and life output -40 °F to +185 °F
• Temperature compensation for Power Save Mode • Can be permanently connected
battery charging • Once the battery is fully charged to battery and AC supply. No need
• Low output ripple and tight load & the chargers switch to eco-power to disconnect through high load
line regulation to save energy conditions
• Four indication LEDs Communication • Lightweight design <2Kg
• Integrated ORing diode for • Can be integrated into external • Works at very high ambient
paralleing applications systems through MODBUS RTU temperatures (80 ºC/185 °F)
• 570W max output power using RS485 • Fanless design
Full Protection • Fully configurable via DSE • Wide line voltage operation
• AC input under voltage Configuration Suite PC Software for • Plastic terminal cover available for
• AC input over voltage special charging requirements safety
• Battery charger output over voltage • External remote LCD option • Deep sleep mode to reduce power
• Battery charger output over current • DSENet® compatibility consumption from battery when
• Battery low voltage detection mains supply unavailable
• Battery temperature compensation
with over temperature protection

RELATED MATERIALS
TITLE PART NO.
DSE9400 Series Configuration Suite PC Software Manual 057-159
DSE Configuration Suite Installation & Operator Manual 057-151
DSE9476 Installation Instructions 053-235
DSE9400 Operator Manual 057-085

DEEP SEA ELECTRONICS PLC UK DEEP SEA ELECTRONICS INC USA

Highfield House, Hunmanby Industrial Estate, Hunmanby YO14 0PH 3230 Williams Avenue, Rockford, IL 61101-2668 USA
TELEPHONE +44 (0) 1723 890099 FACSIMILE +44 (0) 1723 893303 TELEPHONE +1 (815) 316 8706 FACSIMILE +1 (815) 316 8708
EMAIL [email protected] WEBSITE www.deepseaplc.com EMAIL [email protected] WEBSITE www.deepseausa.com
Deep Sea Electronics Plc maintains a policy of continuous development and reserves the right to change Registered in England & Wales No.01319649
the details shown on this data sheet without prior notice. The contents are intended for guidance only. VAT No.316923457 055-244/01/18 (1)
 DSEPower ®

DSE9476 ENVIRONMENTAL TESTING STANDARDS

ELECTRO-MAGNETIC COMPATIBILITY
INTELLIGENT BATTERY CHARGER BS EN 61000-6-2
EMC Generic Immunity Standard for

24 V 20 AMP the Industrial Environment

BS EN 61000-6-4
EMC Generic Emission Standard for
the Industrial Environment

The DSE9476 intelligent battery The chargers do not include any OPERATING TEMPERATURE RANGE
charger can be programmed for moving parts to give added durability BS EN 60068-2-1
Ab/Ae Cold Test -30 ºC
different charging curves to maximise and reliability. They will also continue BS EN 60068-2-2
the life of the battery. to operate during engine cranking and Bb/Be Dry Heat +80 ºC
running. * Refer to de-rating curve in the DSE9476
The DSE9476 is programmed using Operator Manual
the user-friendly DSE Configuration Multiple chargers can be linked VIBRATION
Suite PC software. together to provide a larger current BS EN 60068-2-6
output. Ten sweeps in each of three
major axes
The charger is mounted to the chassis 5 Hz to 8 Hz ar +/-7.5 mm,
using the fixing holes that are built 8 Hz to 500 Hz at 2 gn
into the case. The chargers’ stylish
HUMIDITY
design includes three coloured LEDs
BS EN 60068-2-30
to indicate charging status and fault Db Damp Heat Cyclic 20/55 ºC
conditions. at 95% RH 48 Hours
BS EN 60068-2-78
Cab Damp Heat Static 40 ºC
at 93% RH 48 Hours

SHOCK
BS EN 60068-2-27
Three shocks in each of three major axes
15 gn in 11 mS

COMPREHENSIVE FEATURE LIST TO SUIT A WIDE VARIETY OF BATTERY

CHARGER APPLICATIONS

055-244/01/18 (1)