Scribd Logo
Upload

Welcome to Scribd!

  • 49 views

    NCPP CSM Instrument Panel Manual

    Uploaded by

    Sebastian Vanderlinden
    This document provides an overview and instructions for the main controls and instrumentation on the 3 panels of the NCPP CSM instrument panel. It describes the functions of over 50 switches, gauges, indicators and windows including those for altitude, acceleration, propulsion systems, navigation, docking, cabin controls and more. Instructions are provided for procedures like engine starts, separations, docking and EVA. The simulation aims to recreate the essential displays and operations of the Apollo Command and Service Module flight deck.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    NCPP CSM Instrument Panel Manual

    Uploaded by

    Sebastian Vanderlinden
    49 views10 pages
    This document provides an overview and instructions for the main controls and instrumentation on the 3 panels of the NCPP CSM instrument panel. It describes the functions of over 50 switches, gauges, indicators and windows including those for altitude, acceleration, propulsion systems, navigation, docking, cabin controls and more. Instructions are provided for procedures like engine starts, separations, docking and EVA. The simulation aims to recreate the essential displays and operations of the Apollo Command and Service Module flight deck.

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides an overview and instructions for the main controls and instrumentation on the 3 panels of the NCPP CSM instrument panel. It describes the functions of over 50 switches, gauges, indicators and windows including those for altitude, acceleration, propulsion systems, navigation, docking, cabin controls and more. Instructions are provided for procedures like engine starts, separations, docking and EVA. The simulation aims to recreate the essential displays and operations of the Apollo Command and Service Module flight deck.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    49 views10 pages

    NCPP CSM Instrument Panel Manual

    Uploaded by

    Sebastian Vanderlinden
    This document provides an overview and instructions for the main controls and instrumentation on the 3 panels of the NCPP CSM instrument panel. It describes the functions of over 50 switches, gauges, indicators and windows including those for altitude, acceleration, propulsion systems, navigation, docking, cabin controls and more. Instructions are provided for procedures like engine starts, separations, docking and EVA. The simulation aims to recreate the essential displays and operations of the Apollo Command and Service Module flight deck.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 10

    NCPP CSM Instrument Panel Manual version 1.

    0 beta
    _____________________________________________

    Main controls, Panel 1 (left hand panel)


    1 CMP (Crew Module Pilot) Rendezvous Window

    2 Altimeter:
    Shows altitude in feet MSL (Mean Sea Level). The drogue shutes deploy at
    about 20.000 ft. The Main chutes should fully open at about 10.000 ft MSL.

    3 EMS (Entry Monitor System) Display (NOT SIMULATED)


    But it can be switched on by using the rotary (4). Click on “ENTRY” will turn on
    the EMS Display.

    5 EMS Delta Velocity Display


    In NASSP it displays the current altitude of the space craft.

    6 G-Meter Gauge
    Displays the G-acceleration of the space craft during SPS burn’s and entry
    interface. Normal readout during re-entry should be ~6 G’s.

    7 LV alpha/SPS Pc Gauge
    Displays the engine pressure of the LV (Launch Vehicle) or SPS (Service
    Propulsion System).

    8 FDAI (Flight Director and Attitude Indicator) (NOT SIMULATED).


    Works like an artificial horizon.

    9 LV (Launch Vehicle) Launch Indicator


    The first two needles (left) indicate the fuel quantity of the second stage “SII”.
    The next two needles indicate the third stage (S-IVB) oxid quantity. And the
    four needles on the right indicate the S-IVB fuel quantity.

    10 Launch Lights
    The 6 launch lights indicate the lift off, LES (Launch Escape System) tower
    jettison and the opening sequences of the CM parachutes for entry and
    splashdown.

    11 LV Engines Lights
    1,2,3,4 and 5 lights up when all five engines of the saturn’s first and/or second
    stage are running. LV GUID lights up when the guidance is controlled by the
    CMC (Crew Module Computer) depending on switch 36 (if it’s switched to
    AUTO the guidance is controlled by the CMC auto system, FREE disengages
    the auto guidance). SII SEP lights up when the second stage will separate. LV
    RATE lights up as long as fuel flows.

    12 Abort Push Button


    Pressing the abort push button will abort and separate the current stage of the
    ascent (first stage, second stage and third stage).

    13 Master Alarm Light/Button Shows you that anything is going wrong.


    14, 15, 16 These switches activate one of the three orbiter’s HUD modes. RNDZ
    (Rendezvous – DOCKING MODE), LVLH (Local Vertical/Local Horizon
    – SURFACE MODE) and ORBIT (ORBIT MODE).

    17, 18, 19 These switches turn on or of the SM-RCS (Service Module-Reaction


    Control System) Roll, Pitch and YAW mode, if the SM-RCS is activated
    (see “CSM-RCS Checklist”).

    20, 21 20 changes between SM-RCS thrust power 100% (HIGH) and 50%
    (LOW). 21 changes between TRANSLATION mode and ROTATION
    mode.

    22, 23, 24 These switches turn on or of the CM-RCS (Crew Module-Reaction


    Control System) Roll, Pitch and YAW mode, if the CM-RCS is activated
    (see “CSM-RCS Checklist”).

    25, 26, 27 These switches turn on or of the S-IVB RCS (Third Stage-Reaction
    Control System) Roll, Pitch and YAW mode.

    28, 29 The two S-IVB GIMBAL MOTOR switches turn on or off the
    PITCH/YAW gimbal motors of the third stage.

    30 These switch activates the SPS for burn procedures. The four
    INJECTOR VALVE indicators on panel 3 (right hand panel) should
    indicate “OPEN”!

    31, 32, 33, 34 The four switches should be used to enable the SPS gimbal
    motors.

    35 Open the guard (right mouse click) and push the button CSM/LV SEP
    to separate the CSM from S-IVB after Trans Lunar Injection or S-IVB
    shutdown.

    37 The SC CONT switch in CMC position activates the orbital monitoring.


    The engines will cut off when the smallest value of excentricity is
    achieved.

    38 Direct Ullage Light Direct ullage.

    39 Thrust On Light Thrust is on.


    DSKY, Abort and Separation Controls, Panel 2 (center panel)

    Right click for opening switch guards!

    1 EDS (Emergency Detection System). The EDS provides automatic


    abort if an engine failure occurs before 100 sec flight is achieved.

    2 CSM/LM final separation. No LM (Lunar Module) docking possible after


    separation. Docking probe separation!

    3 CSM/LM SEP 2 separates the LM from CSM without separation of the


    docking probe. Re-docking to the LM is possible!

    4, 5 Use these two switches to separate the SM from CM before entry


    interface.
    6 Once you have docked the CSM to the LEM after S-IVB/CSM
    separation, use the S-IVB/LM switch for lunar module extraction from S-
    IVB!

    7, 8 The two TWR JET switches jettison the launch escape tower (LES)
    manually after first stage interstage separation, when the LES doesn’t
    jettison automatically.

    9 Use these switch to separate the SII from S-IVB if you want to abort
    second stage without pressing the abort push button.

    10 X-LUNAR INJECTION is used to activate and fire the S-IVB for Trans
    Lunar Injection.

    11 MAIN RELEASE opens the main parachutes manually after entry


    interface if they doesn’t open automatically.
    Docking Probe and SM-RCS Controls, Panel 2 (center panel)

    1 This indicator indicates the temperature (left scale) and He press (right
    scale) of the SM-RCS. Simulation not realistic yet!

    2 This indicator indicates the propellant He press/propellant quantity of


    the SM-RCS.

    3-10 SM RCS HELIUM 1 and 2 switches are used to pressurize the SM RCS
    Helium tanks. They should be switched to CLOSE before activating the
    SM RCS.
    11-18 The propellant switches should be switched to OPEN before activating
    the SM RCS.

    19 Once you have docked the CSM to the LEM open the guard of the
    DOCKING PROBE switch and switch it to EXTD/REL. The TB (Talk
    Back Indicator) should change from gray to BP (Barber Pole). Before
    CSM/LM separation switch it back to RETRACT.

    See “CSM-RCS Checklist” for activating the SM RCS!

    Caution and Warning System, Panel 2 (center panel)

    1 C/W lamps are not simulated yet. But the lamps can be light up during a
    test by switching the test switch (2) to LAMP TEST.

    3 Mission Timer
    Cabin Pressurization and EVA, Panel 2 (center panel)

    The simulation of the cabin pressurization is still very simple on version 1.0 beta.

    EVA :

    1 switch the cabin press to decrease. The indicator needles of gauge 4, 5 and 6
    (CABIN, CABIN and PART PRESS O2) go down. Then simply open the hatch (2)
    and start you EVA (3).

    Switch 7 and 8 are used to switch on or of the cabin fans. You can here them!
    SPS Gauges, Panel 3 (right hand panel)

    1 Indicates the temperature and He press of the SPS fuel (not realistic
    yet).

    2 Indicates press and quantity of the SPS fuel and oxid.

    3 The SPS ENGINE INJECTOR VALVES should indicate OPEN when


    the SPS THRUST switch on panel 1 (left hand panel) is witched to
    DIRECT ON. To activate the SPS for burn and/or midcourse corrections
    simply switch the SPS THRUST switch to DIRECT ON.
    Docking Window View (STRG + ARROW UP)

    The docking window is 1152x864 pixels for those who using 19 inch monitors. With a
    resolution of 1152x864 it works perfect. For a resolution of 1024x768 the docking
    procedure should work as followed:

    Simply scroll to the upper left corner. The COAS (Crewman Optical Align Sight)
    should point the right way to the LM docking target.

    That’s it, so far…

    By Matthias Müller ([email protected])

    You might also like