GENERAL NOTES:-

1.ALL DIMENSIONS ARE IN MM UNLESS OTHERWISE SPECIFIED.

2.THIS DRAWING SHOULD BE READ IN CONJUNCTION WITH RELEVANT

ARCHITECTURAL & WORKING DRAWING. IF ANY DISCREPANCY FOUND, SHOULD
BE IMMEDIATELY BROUGHT TO NOTICE OF THIS OFFICE, BEFORE EXECUTION OF
WORK.

3.ONLY WRITTEN DIMENSION ARE TO BE FOLLOWED.

4.FOR SLABS,BEAMS AND COLUMNS AND FOOTING CONC. GRADE SHALL BE OF M

30( DESIGN MIX ).

5.REINFORCEMENT DETAILS

STRENGTH 500 N/MM2 CONFORMING TO IS 1786-1985, SHALL BE USED.

B.LAP IN SLAB OF SUPER STRUCTURE CLOSE TO MID SPAN FOR BOTTOM BARS &
CLOSE TO SUPPORT FOR TOP BARS SHALL BE AVOIDED.

6.THE LONGITUDINAL BARS OF BEAM SHALL BE SPLICED ONLY, IF HOOPS

STRUCTURE ARE PROVIDED OVER THE ENTIRE SPLICE LENGTH AT A SPACING
NOT MORE THAN 150MM, AS SHOWN IN FIG-1. LAP SPLICES SHALL NOT BE
PROVIDED.

a)WITHIN A JOINT, b) WITHIN A DISTANCE OF '2d' FROM JOINT FACE AND C) WITHIN A
QUARTER LENGTH OF THE MEMBER WHERE FLEXURAL YIELDING MAY
GENERALLY OCCUR UNDER THE EFFECT OF EARTHQUAKE FORCES . NOT MORE
THAN 50% OF THE BARS SHALL BE SPLICED AT ONE SECTION.

7.CONCRETE DETAILS

a.NOMINAL SIZE OF CRUSHED STONE GRADED AGGREGATE SHALL BE 3/4" UNLESS

OTHERWISE STATED.

b.GRADE OF CONCRETE SHALL BE M-30 (DESIGN MIX).

c.CLEAR COVER OF CONCRETE IN MM TO THE MAIN REINFORCEMENT UNLESS

SPECIFIED OTHERWISE SHALL BE :-

PARTICULAR CLEAR COVER

FOOTING 50MM.
COLUMNS 40MM.
SLAB 20MM.
BEAMS, LINTEL 25MM.
d. EARTHQUAKE PROVISION HAS BEEN TAKEN AS IS-1893 FOR ZONE III

8. H (HEIGHT OF PEDESTAL) - VARIES AS MENTIONED IN SCHEDULED, BASED ON

THE ACTUAL HEIGHT OF FOOTINGS.

9. TOP LEVELS OF ALL PEDESTALS ARE TO BE KEPT AT ONE LEVEL BY PROVIDING

DIFFERENT HEIGHTS OF PEDESTALS.

10.HEIGHT OF COLUMNS ABOVE PEDESTALS UP TO TOP OF PLINTH IS 1500MM. THIS

SHOULD BE STRICTLY FOLLOWED.FOR ANY DEVIATION AS PER SITE CONDITION,
SHOULD BE BROUGHT TO THE NOTICE OF STRUCTURAL ENGINEER.

11. NET SAFE BEARING CAPACITY OF THE SOIL HAS BEEN CONSIDERED 15 T/Sqm
AT A DEPTH OF 2500MM BELOW THE EXISTING GROUND LEVEL AS PER SUB-SOIL
INSPECTION REPORT PREPARED BY " ASLESHA CONSULTANCY SERVICES",
BHUBANESWAR

12.THE BUILDING HAS BEEN DESIGNED FOR G+2 STORIED WITHOUT ANY PROVISION
FOR HORIZONTAL & VERTICAL EXTENSIONS IN FUTURE AT A LATER DATE.

13. DEVELOPMENT LENGTH 'Ldt' AND LAP LENGTH IN TENSION/COMPRESSION

SHALL BE AS PER IS/456-2000, WHICH SHALL NOT BE LESS THAN 50 TIMES THE
DIAMETER OF BARS RESPECTIVELY FOR USING GRADE OF CONCERT M30.

14. IF ANY ACTUAL SUB-SOIL CONDITION DURING EXCAVATION DIFFER FROM AS

REPORTED OR LOOSE STRATA FOUND THE SAME MAY BE REPORTED
STRUCTURAL ENGINEER.

15. ANY DISCREPANCY AMONG THIS STRUCTURAL DRAWINGS THE

CORRESPONDING ARCHITECTURAL DRAWINGS AND THE AGREEMENT ITEM IF
ANY SHALL BE RECONCILED BEFORE EXECUTION.

16. ANY DISCREPANCY FOUND IN STRUCTURE DRAWINGS BRING NOTICED OF THE

STRUCTURAL ENGINEER BEFORE EXECUTION AT THE SITE.

idco ODISHA INDUSTRIAL INFRASTRUCTURE

DEVELOPMENT CORPORATION , IDCO ,IDCO TOWERS,
YOUR POWER JANPATH ,BHUBANESWAR .
TO GROW

WORKER'S HOSTEL AT JAYAMANGAL,

PROJECT
ODISHA
BLOCK-E DINING & MULTIPURPOSE HALL
TITLE
DRAWING FOUNDATION PLAN & DETAIL(SHEET 1 OF 2)

SCALE NTS DATE 21-04-2023

DRAWN DESIGNED CHECKED APPROVED

WH/ JDA/ARCH /GFC/STR- 101 REVISIONS

DRG. NO.
0 1
REVISIONS
IDCO DRG. NO.
0
 COMBINED FOOTING DETAIL GENERAL NOTES:-
1.ALL DIMENSIONS ARE IN MM UNLESS OTHERWISE SPECIFIED.

2.THIS DRAWING SHOULD BE READ IN CONJUNCTION WITH RELEVANT

ARCHITECTURAL & WORKING DRAWING. IF ANY DISCREPANCY FOUND, SHOULD
BE IMMEDIATELY BROUGHT TO NOTICE OF THIS OFFICE, BEFORE EXECUTION OF
WORK.

3.ONLY WRITTEN DIMENSION ARE TO BE FOLLOWED.

4.FOR SLABS,BEAMS AND COLUMNS AND FOOTING CONC. GRADE SHALL BE OF M

30( DESIGN MIX ).

5.REINFORCEMENT DETAILS

STRENGTH 500 N/MM2 CONFORMING TO IS 1786-1985, SHALL BE USED.

B.LAP IN SLAB OF SUPER STRUCTURE CLOSE TO MID SPAN FOR BOTTOM BARS &
CLOSE TO SUPPORT FOR TOP BARS SHALL BE AVOIDED.

6.THE LONGITUDINAL BARS OF BEAM SHALL BE SPLICED ONLY, IF HOOPS

STRUCTURE ARE PROVIDED OVER THE ENTIRE SPLICE LENGTH AT A SPACING
NOT MORE THAN 150MM, AS SHOWN IN FIG-1. LAP SPLICES SHALL NOT BE
PROVIDED.

a)WITHIN A JOINT, b) WITHIN A DISTANCE OF '2d' FROM JOINT FACE AND C) WITHIN A
QUARTER LENGTH OF THE MEMBER WHERE FLEXURAL YIELDING MAY
GENERALLY OCCUR UNDER THE EFFECT OF EARTHQUAKE FORCES . NOT MORE
THAN 50% OF THE BARS SHALL BE SPLICED AT ONE SECTION.

7.CONCRETE DETAILS

a.NOMINAL SIZE OF CRUSHED STONE GRADED AGGREGATE SHALL BE 3/4" UNLESS

OTHERWISE STATED.
ISOLATED FOOTING DETAIL
b.GRADE OF CONCRETE SHALL BE M-30 (DESIGN MIX).

c.CLEAR COVER OF CONCRETE IN MM TO THE MAIN REINFORCEMENT UNLESS

SPECIFIED OTHERWISE SHALL BE :-

PARTICULAR CLEAR COVER

FOOTING 50MM.
COLUMNS 40MM.
SLAB 20MM.
BEAMS, LINTEL 25MM.
d. EARTHQUAKE PROVISION HAS BEEN TAKEN AS IS-1893 FOR ZONE III

8. H (HEIGHT OF PEDESTAL) - VARIES AS MENTIONED IN SCHEDULED, BASED ON

THE ACTUAL HEIGHT OF FOOTINGS.

9. TOP LEVELS OF ALL PEDESTALS ARE TO BE KEPT AT ONE LEVEL BY PROVIDING

DIFFERENT HEIGHTS OF PEDESTALS.

10.HEIGHT OF COLUMNS ABOVE PEDESTALS UP TO TOP OF PLINTH IS 1500MM. THIS

SHOULD BE STRICTLY FOLLOWED.FOR ANY DEVIATION AS PER SITE
CONDITION, SHOULD BE BROUGHT TO THE NOTICE OF STRUCTURAL
ENGINEER.
NOTE:- BOTTOM REINFORCEMENTS PARALLEL TO LENGTH OF FOOTING 11. NET SAFE BEARING CAPACITY OF THE SOIL HAS BEEN CONSIDERED 15 T/Sqm
ARE TO BE KEPT AT BOTTOM AS MAIN REINFORCEMENT AT A DEPTH OF 2500MM BELOW THE EXISTING GROUND LEVEL AS PER
SUB-SOIL INSPECTION REPORT PREPARED BY " ASLESHA CONSULTANCY
SERVICES", BHUBANESWAR

PLINTH BEAM. Plinth Level. 12.THE BUILDING HAS BEEN DESIGNED FOR G+2 STORIED WITHOUT ANY PROVISION
FOR HORIZONTAL & VERTICAL EXTENSIONS IN FUTURE AT A LATER DATE.

13. DEVELOPMENT LENGTH 'Ldt' AND LAP LENGTH IN TENSION/COMPRESSION

SHALL BE AS PER IS/456-2000, WHICH SHALL NOT BE LESS THAN 50 TIMES THE
DIAMETER OF BARS RESPECTIVELY FOR USING GRADE OF CONCERT M30.

OUTSIDE OF INSIDE OF BUILDING. 14. IF ANY ACTUAL SUB-SOIL CONDITION DURING EXCAVATION DIFFER FROM AS
REPORTED OR LOOSE STRATA FOUND THE SAME MAY BE REPORTED
STRUCTURAL ENGINEER.
BUILDING. Existing Ground Level. 15. ANY DISCREPANCY AMONG THIS STRUCTURAL DRAWINGS THE
CORRESPONDING ARCHITECTURAL DRAWINGS AND THE AGREEMENT ITEM IF
ANY SHALL BE RECONCILED BEFORE EXECUTION.

16. ANY DISCREPANCY FOUND IN STRUCTURE DRAWINGS BRING NOTICED OF THE

STRUCTURAL ENGINEER BEFORE EXECUTION AT THE SITE.
B, b = Parallel to Y axis
Pedestal vertical R/f. A, a = Parallel to X axis
10-#12(TYP) Lateral ties for Pedestals
(Confined R/f)
Lateral ties 2500 (TYP)
#8 @ 75 c/c Lateral ties 150 a 150
150 MM 10-#12 (Typ)
150 (Confined R/f) idco
REINF. ALONG `B'

ODISHA INDUSTRIAL INFRASTRUCTURE

10-#12 (Typ)
150 B DEVELOPMENT CORPORATION , IDCO ,IDCO TOWERS,

H A A
YOUR POWER JANPATH ,BHUBANESWAR .
300

TO GROW
bb b
WORKER'S HOSTEL AT JAYAMANGAL,
PROJECT
ODISHA
D= Depth. 150 Vertical R/f of pedestal
Minimum aa TITLE BLOCK-E DINING & MULTIPURPOSE HALL
300(TYP) as per details of
3 nos.
Pedestals. DRAWING FOUNDATION PLAN & DETAIL(SHEET 2 OF 2)
300 (Typ) REINF. ALONG `A'
150 B 150 Lateral ties 8# @ 75
SCALE NTS DATE 21-04-2023

APPROVED
Bottom R/f both c/c (1 no. closed
DRAWN DESIGNED CHECKED
150 mm thick lean 150
way.(TYP) concrete. rectangular ties.
A
SECTION AA (TYP)
TYPICAL PLAN OF
ISOLATED FOOTINGS DRG. NO.
WH/ JMA/ARCH /GFC/STR- 102 REVISIONS
ISOLATED FOOTINGS 0 1
REVISIONS
IDCO DRG. NO.
0
 GENERAL NOTES:-
1.ALL DIMENSIONS ARE IN MM UNLESS OTHERWISE SPECIFIED.

2.THIS DRAWING SHOULD BE READ IN CONJUNCTION WITH RELEVANT

ARCHITECTURAL & WORKING DRAWING. IF ANY DISCREPANCY FOUND, SHOULD
BE IMMEDIATELY BROUGHT TO NOTICE OF THIS OFFICE, BEFORE EXECUTION OF
WORK.

3.ONLY WRITTEN DIMENSION ARE TO BE FOLLOWED.

4.FOR SLABS,BEAMS AND COLUMNS AND FOOTING CONC. GRADE SHALL BE OF M

30( DESIGN MIX ).

5.REINFORCEMENT DETAILS

STRENGTH 500 N/MM2 CONFORMING TO IS 1786-1985, SHALL BE USED.

B.LAP IN SLAB OF SUPER STRUCTURE CLOSE TO MID SPAN FOR BOTTOM BARS &
CLOSE TO SUPPORT FOR TOP BARS SHALL BE AVOIDED.

6.THE LONGITUDINAL BARS OF BEAM SHALL BE SPLICED ONLY, IF HOOPS

STRUCTURE ARE PROVIDED OVER THE ENTIRE SPLICE LENGTH AT A SPACING
NOT MORE THAN 150MM, AS SHOWN IN FIG-1. LAP SPLICES SHALL NOT BE
PROVIDED.

a)WITHIN A JOINT, b) WITHIN A DISTANCE OF '2d' FROM JOINT FACE AND C) WITHIN A
QUARTER LENGTH OF THE MEMBER WHERE FLEXURAL YIELDING MAY
GENERALLY OCCUR UNDER THE EFFECT OF EARTHQUAKE FORCES . NOT MORE
THAN 50% OF THE BARS SHALL BE SPLICED AT ONE SECTION.

7.CONCRETE DETAILS

a.NOMINAL SIZE OF CRUSHED STONE GRADED AGGREGATE SHALL BE 3/4" UNLESS

OTHERWISE STATED.

b.GRADE OF CONCRETE SHALL BE M-30 (DESIGN MIX).

c.CLEAR COVER OF CONCRETE IN MM TO THE MAIN REINFORCEMENT UNLESS

SPECIFIED OTHERWISE SHALL BE :-

PARTICULAR CLEAR COVER

FOOTING 50MM.
COLUMNS 40MM.
SLAB 20MM.
BEAMS, LINTEL 25MM.
d. EARTHQUAKE PROVISION HAS BEEN TAKEN AS IS-1893 FOR ZONE III

8. H (HEIGHT OF PEDESTAL) - VARIES AS MENTIONED IN SCHEDULED, BASED ON

THE ACTUAL HEIGHT OF FOOTINGS.

9. TOP LEVELS OF ALL PEDESTALS ARE TO BE KEPT AT ONE LEVEL BY PROVIDING

DIFFERENT HEIGHTS OF PEDESTALS.

10.HEIGHT OF COLUMNS ABOVE PEDESTALS UP TO TOP OF PLINTH IS 1500MM. THIS

SHOULD BE STRICTLY FOLLOWED.FOR ANY DEVIATION AS PER SITE CONDITION,
SHOULD BE BROUGHT TO THE NOTICE OF STRUCTURAL ENGINEER.

11. NET SAFE BEARING CAPACITY OF THE SOIL HAS BEEN CONSIDERED 15 T/Sqm
AT A DEPTH OF 2500MM BELOW THE EXISTING GROUND LEVEL AS PER SUB-SOIL
INSPECTION REPORT PREPARED BY " ASLESHA CONSULTANCY SERVICES",
BHUBANESWAR

12.THE BUILDING HAS BEEN DESIGNED FOR G+2 STORIED WITHOUT ANY PROVISION
FOR HORIZONTAL & VERTICAL EXTENSIONS IN FUTURE AT A LATER DATE.

13. DEVELOPMENT LENGTH 'Ldt' AND LAP LENGTH IN TENSION/COMPRESSION

SHALL BE AS PER IS/456-2000, WHICH SHALL NOT BE LESS THAN 50 TIMES THE
DIAMETER OF BARS RESPECTIVELY FOR USING GRADE OF CONCERT M30.

14. IF ANY ACTUAL SUB-SOIL CONDITION DURING EXCAVATION DIFFER FROM AS

REPORTED OR LOOSE STRATA FOUND THE SAME MAY BE REPORTED
STRUCTURAL ENGINEER.

15. ANY DISCREPANCY AMONG THIS STRUCTURAL DRAWINGS THE

CORRESPONDING ARCHITECTURAL DRAWINGS AND THE AGREEMENT ITEM IF
ANY SHALL BE RECONCILED BEFORE EXECUTION.

16. ANY DISCREPANCY FOUND IN STRUCTURE DRAWINGS BRING NOTICED OF THE

STRUCTURAL ENGINEER BEFORE EXECUTION AT THE SITE.

idco ODISHA INDUSTRIAL INFRASTRUCTURE

DEVELOPMENT CORPORATION , IDCO ,IDCO TOWERS,
YOUR POWER JANPATH ,BHUBANESWAR .
TO GROW

WORKER'S HOSTEL AT JAYAMANGAL,

PROJECT
ODISHA
BLOCK-E DINING & MULTIPURPOSE HALL
TITLE
DRAWING COLUMN DETAILS

SCALE NTS DATE 21-04-2023

DRAWN DESIGNED CHECKED APPROVED

WH/ JMA/ARCH /GFC/STR- 103 REVISIONS

DRG. NO.
0 1
REVISIONS
IDCO DRG. NO.
0
 GENERAL NOTES:-
1.ALL DIMENSIONS ARE IN MM UNLESS OTHERWISE SPECIFIED.

2.THIS DRAWING SHOULD BE READ IN CONJUNCTION WITH RELEVANT

ARCHITECTURAL & WORKING DRAWING. IF ANY DISCREPANCY FOUND, SHOULD
BE IMMEDIATELY BROUGHT TO NOTICE OF THIS OFFICE, BEFORE EXECUTION OF
WORK.
COLUMN SCHEDULE FOUNDATION TO TOP LVL.
3.ONLY WRITTEN DIMENSION ARE TO BE FOLLOWED.
SR. DESCRIPTION OF COLUMN SIZE REINF. STIRRUPS
SHEAR STIRRUPS 4.FOR SLABS,BEAMS AND COLUMNS AND FOOTING CONC. GRADE SHALL BE OF M
NO. SECTIONAL DETAILS
COLUMN (a x b ) END REGION MID REGION
30( DESIGN MIX ).

5.REINFORCEMENT DETAILS
BEAM
STRENGTH 500 N/MM2 CONFORMING TO IS 1786-1985, SHALL BE USED.
C5,C10,C11, C13,
B.LAP IN SLAB OF SUPER STRUCTURE CLOSE TO MID SPAN FOR BOTTOM BARS &
C15,C16,C17, C18, CLOSE TO SUPPORT FOR TOP BARS SHALL BE AVOIDED.
8-#16
1 C20, C21,C22, C23,
350 x 550 +
#8-@75 c/c #8-@175 c/c
C25, C26, C27,C32, 6.THE LONGITUDINAL BARS OF BEAM SHALL BE SPLICED ONLY, IF HOOPS
C33,C34, C39, C44 4-#20 STRUCTURE ARE PROVIDED OVER THE ENTIRE SPLICE LENGTH AT A SPACING
NOT MORE THAN 150MM, AS SHOWN IN FIG-1. LAP SPLICES SHALL NOT BE
PROVIDED.

a)WITHIN A JOINT, b) WITHIN A DISTANCE OF '2d' FROM JOINT FACE AND C) WITHIN A
(20 NOS.) SPLICES QUARTER LENGTH OF THE MEMBER WHERE FLEXURAL YIELDING MAY
GENERALLY OCCUR UNDER THE EFFECT OF EARTHQUAKE FORCES . NOT MORE
THAN 50% OF THE BARS SHALL BE SPLICED AT ONE SECTION.

7.CONCRETE DETAILS
C1,C3,C4,C6,C8,C9,
2 C19,C24,C29,C35,
a.NOMINAL SIZE OF CRUSHED STONE GRADED AGGREGATE SHALL BE 3/4" UNLESS
OTHERWISE STATED.
C36, C37, C38, C42, 6-#16 #8-@75 c/c #8-@175 c/c b.GRADE OF CONCRETE SHALL BE M-30 (DESIGN MIX).
C47,C49 350 x 550 +
c.CLEAR COVER OF CONCRETE IN MM TO THE MAIN REINFORCEMENT UNLESS
(17 NOS.) 6-#20 SPECIFIED OTHERWISE SHALL BE :-

PARTICULAR CLEAR COVER

FOOTING 50MM.
COLUMNS 40MM.
SLAB 20MM.
BEAMS, LINTEL 25MM.
d. EARTHQUAKE PROVISION HAS BEEN TAKEN AS IS-1893 FOR ZONE III
C7,C12,C14,C28,C31, BEAM
3 C40,C41,C45,C46 12-#20
8. H (HEIGHT OF PEDESTAL) - VARIES AS MENTIONED IN SCHEDULED, BASED ON
THE ACTUAL HEIGHT OF FOOTINGS.
350 x 550
#8-@75 c/c #8-@175 c/c 9. TOP LEVELS OF ALL PEDESTALS ARE TO BE KEPT AT ONE LEVEL BY PROVIDING
(8 NOS.) DIFFERENT HEIGHTS OF PEDESTALS.

10.HEIGHT OF COLUMNS ABOVE PEDESTALS UP TO TOP OF PLINTH IS 1500MM. THIS

SHOULD BE STRICTLY FOLLOWED.FOR ANY DEVIATION AS PER SITE
CONDITION, SHOULD BE BROUGHT TO THE NOTICE OF STRUCTURAL
ENGINEER.

11. NET SAFE BEARING CAPACITY OF THE SOIL HAS BEEN CONSIDERED 15 T/Sqm
AT A DEPTH OF 2500MM BELOW THE EXISTING GROUND LEVEL AS PER
SUB-SOIL INSPECTION REPORT PREPARED BY " ASLESHA CONSULTANCY
SERVICES", BHUBANESWAR

C2,C30,C43,C48 Fig-(A) 12.THE BUILDING HAS BEEN DESIGNED FOR G+2 STORIED WITHOUT ANY PROVISION
4 8-#20
FOR HORIZONTAL & VERTICAL EXTENSIONS IN FUTURE AT A LATER DATE.
350 x 550 13. DEVELOPMENT LENGTH 'Ldt' AND LAP LENGTH IN TENSION/COMPRESSION
+ #8-@75 c/c #8-@175 c/c SHALL BE AS PER IS/456-2000, WHICH SHALL NOT BE LESS THAN 50 TIMES THE
(4 NOS.) 4-#25 DIAMETER OF BARS RESPECTIVELY FOR USING GRADE OF CONCERT M30.

14. IF ANY ACTUAL SUB-SOIL CONDITION DURING EXCAVATION DIFFER FROM AS

REPORTED OR LOOSE STRATA FOUND THE SAME MAY BE REPORTED
STRUCTURAL ENGINEER.

15. ANY DISCREPANCY AMONG THIS STRUCTURAL DRAWINGS THE

CORRESPONDING ARCHITECTURAL DRAWINGS AND THE AGREEMENT ITEM IF
TOTAL = (49 NOS.) ANY SHALL BE RECONCILED BEFORE EXECUTION.

16. ANY DISCREPANCY FOUND IN STRUCTURE DRAWINGS BRING NOTICED OF THE

STRUCTURAL ENGINEER BEFORE EXECUTION AT THE SITE.

TYPICAL DETAIL OF HOOKS

idco ODISHA INDUSTRIAL INFRASTRUCTURE

DEVELOPMENT CORPORATION , IDCO ,IDCO TOWERS,
YOUR POWER JANPATH ,BHUBANESWAR .
CROSSTIE TO GROW

WORKER'S HOSTEL AT JAYAMANGAL,

PROJECT
ODISHA
BLOCK-E DINING & MULTIPURPOSE HALL
TITLE
DETAIL OF STIRRUPS IN COLUMN CORE REGION DRAWING COLUMN SCHEDULE

Fig-(B) SCALE NTS DATE 21-04-2023

DRAWN DESIGNED CHECKED APPROVED

WH/ JDA/ARCH /GFC/STR- 104 REVISIONS

DRG. NO.
0 1
REVISIONS
IDCO DRG. NO.
0