2050-STSTD-00117 /

PAGE NO. 29
STANDARD JOINT DETAILS - BEAM TO BEAM WEB SHEAR CONNECTION 4355-AI-DX-00000017
TYPE - ' DS '
TYPE - ' DS '
PROFILE - W 01 OF 02 0

GENERAL NOTES:
1) ALL DIMENSIONS ARE GIVEN IN MILLIMETERS (UNO).
2) FOR LOCATION OF APPLICATION OF THIS STANDARD REFER DESIGN
DRAWINGS WITH NOTATION "DS".
TYPICAL CONNECTION DETAIL FOR BEAM TO BEAM "DS" CONNECTION TYPICAL DETAIL SHOWING WEB FILLER PLATE TABLE-A : WELD SIZES 3) MATERIAL:
STRUCTURAL STEEL W & WT SECTION & CHANNELS : ASTM A992 / A992M, ASTM A572 / A572M Grade 50
BUILT UP SHAPES & PLATES : ASTM A572 / A572M Grade 50
GUSSET/STIFFENER FILLET WELD SIZE STRUCTURAL ANGLES AND CHANNELS : ASTM A36
PLATE THICKNESS (W)
PLAN VIEW 1 SPLICE PLATE
4) ALL FILLET WELD SIZES MENTIONED ARE SIDES OF THE WELD.
10mm
SCALE: N.T.S. - (TYP) (2 NOS. NS/FS) mm mm

10 8
BEAM WEB
Lsp 12 10

16 12
10mm
Ø DIA A325M/A325 HSB 20 12
SUPPORTING BEAM 10mm
edh edh edh edh SPLICE PLATE GUSSET PLATE FILLER PLATE (TYP)
(2 NOS NS/FS) (IF GRATER THAN 25 12
2mm)

tsp

A
edv
tg

NOTE : WHERE SUPPORTING BEAM WEB THICKNESS IS SMALLER

THAN WELD SIZE OF GUSSET MENTIONED, THE FILLET
WELD SIZE SHALL BE SAME AS THE WEB THICKNESS.

pv pv pv pv pv
tsp

Hsp
SUPPORTED BEAM

LEGENDS

edv
DS = BEAM TO BEAM FIN PLATE SHEAR CONNECTION
* FILLER PLATE (IF REQUIRED) Nbr = NO. OF BOLT ROWS
Nbc = TOTAL NO. OF BOLT COLUMN IN BEAM & GUSSET
GUSSET PLATE W 3 SIDES (TYP)
REFER TABLE A Nbt = TOTAL NO. OF BOLT IN CONNECTION
W
Nbr X Nbc
NS & FS = NEAR SIDE & FAR SIDE

* NOTE : THIS LENGTH OF BOTTOM FLANGE TO BE CUT AS PER NOTE (REMARKS) INDICATED IN TABLE BELOW
WHEREVER REQUIRED TO AVOID CLASH WITH FLANGE.

CONNECTION DETAILS TABLE FOR "DS" CONNECTION

STIFFENER DETAIL SPLICE PLATE DETAILS BOLT DETAILS
SUPPORTED tg Lsp Hsp tsp Ø Nbr Nbc edh edv pv A REMARKS
Nbt
BEAM
mm mm mm mm mm (nos.) (nos.) (Nbr X Nbc) mm mm mm mm
10 2 2 4
W6X15/W6X25 10 170 120 M20 40 30 60 18
10 2 2 4
W8X18/W8X21/W8X24/W8X28/W8X31/W8X40 10 170 140 M20 40 40 60 30
10 3 2 6
W10X22/W10X26/W10X30 10 170 200 M20 40 40 60 40
10 3 2 6
W10X33/W10X39/W10X49/W10X54/W10X60/W10X68 10 170 200 M20 40 40 60 30
10 3 2 6
W12X26/W12X35/W12X40/W12X50/W12X53/W12X65/W12X87 10 170 200 M20 40 40 60 45
10 4 2 8
W14X30/W14X34/W14X38/W14X43/W14X48/W14X53/W14X61/W14X82/W14X90 10 170 260 M20 40 40 60 50
10 5 2 10
W16X36/W16X40/W16X45 12 170 320 M20 40 40 60 40
10 5 2 10
W16X50/W16X57/W16X67/W16X77/W16X89 12 170 320 M20 40 40 60 45
10 6 2 12
W18X50/W18X55/W18X60/W18X65/W18X71 12 170 380 M20 40 40 60 40
10 6 2 12
W18X76/W18X86/W18X97 12 170 380 M20 40 40 60 45
10 7 2 14
W21X44/W21X62/W21X93/W21X101/W21X122 16 170 440 M20 40 40 60 50
10 8 2 16
W24X104/W24X131/W24X146/W24X162/W24X176/W24X207/W24X229 16 170 500 M20 40 40 60 70
10 9 2 18
W27X102/W27X114/W27X129 16 170 560 M20 40 40 60 50
10 10 2 20
W30X116/W30X132/W30X148 16 170 620 M20 40 40 60 60
10 12 2 24
W33X130/W33X152/W33X169 16 170 740 M20 40 40 60 55
12 13 2 26
W36X135/W36X182/W36X210/W36X256 20 170 800 M20 40 40 60 70 FOR W36X135 & W36X182 USE A = 55mm

12 WHEREVER REQUIRED, CUT THE BEAM FLANGE

W40X324/W40X362/W40X397/W40X503 25 170 860 M20 14 2 28 40 40 60 100 & GRIND SMOOTH FILLET RADIUS OF BEAM.

from reference excel

 2050-STSTD-00117 /
PAGE NO. 30
STANDARD JOINT DETAILS - BEAM TO BEAM WEB SHEAR CONNECTION 4355-AI-DX-00000017
TYPE - ' DS '
TYPE - ' DS '
CAPACITY TABLE 02 OF 02 0

GENERAL NOTES:
CAPACITY TABLE FOR "DS" TYPE CONNECTION (VALID FOR d1 > d2) CAPACITY TABLE FOR "DS" TYPE CONNECTION (VALID FOR d 1> d2) TABLE FOR GROUP BEAM 1) ALL DIMENSIONS ARE GIVEN IN MILLIMETERS (UNO).
(NOTE : CAPACITIES ARE CALCULATED ACCORDING TO WORST MAXIMUM ECCENTRICITY OF THE EXTERNAL BOLT GROUP) (NOTE : CAPACITIES ARE CALCULATED ACCORDING TO WORST MAXIMUM ECCENTRICITY OF THE EXTERNAL BOLT GROUP) (NOTE : GROUPS ARE MADE ACCORDINGLY TO 2) FOR LOCATION OF APPLICATION OF THIS STANDARD REFER DESIGN
DRAWINGS WITH NOTATION "DS".
WIDTH OF FLANGE OF SUPPORTING BEAM)
3) MATERIAL:
STRUCTURAL STEEL W & WT SECTION & CHANNELS : ASTM A992 / A992M, ASTM A572 / A572M Grade 50
BUILT UP SHAPES & PLATES : ASTM A572 / A572M Grade 50
STRUCTURAL ANGLES AND CHANNELS : ASTM A36
4) ALL FILLET WELD SIZES MENTIONED ARE SIDES OF THE WELD.

LEGENDS
DS = BEAM TO BEAM FIN PLATE SHEAR CONNECTION
V = ACTUAL DESIGN SHEAR
T = ACTUAL AXIAL FORCE
Va
α =
Ta
Va = ALLOWABLE SHEAR CAPACITY OF CONNECTION
Ta = ALLOWABLE AXIAL FORCE CAPACITY OF CONNECTION
d1 = DEPTH OF SUPPORTING BEAM
d2 = DEPTH OF SUPPORTED BEAM

RULES FOR VERFICATION

1. V+ α T <_ Va

follow excel given - this

is for reference only