Department of Education

Schools Division Office

VICTORINO MAPA HIGH SCHOOL
TECHNOLOGY AND LIVELIHOOD EDUCATION
San Miguel, Manila
Learning Area: TLE-CARPENTRY Teaching Date: Thurs, March 2, 2023
Fri, March 3, 2023

Grade & Section: Grade 8- Sections 9, 16, 11 Time: 6:30 AM -11:45 AM

&6, 13
Class size: 25 , 25, 26 , 26, 25

I I. OBJECTIVES: The teacher will lead the class into a

At the end of the lesson 100 % of the watching a video in preparation of their long
learners with 85% should be quiz.
able to: B. PRESENTATION OF THE LESSON
1. Describe tools and materials in carpentry
 The teacher will start instructing the
2. Prepare Tools and materials for a task
students on how to answer the long
3.Apply the use of tools and materials.
quiz.
II. GENERAL COMPETENCY:  The teacher will explain the rules in
taking the quiz:
 IDENTIFY MATERIALS AND TOOLS FOR A
1. There should be no erasure.
TASK
2. All notebooks should be collected.
Specific Competency (Topic): 3. No glancing (1 warning)
4. Keep quiet
 Carpentry Tools:
 After 30 minutes, the papers will be
A.) Measuring Tools
collected.
B.) Mark Lining Tools
C.) Testing Tools
D.) Edge Cutting Tools C. APPLICATION
E.) Tooth-Cutting Tools Students will apply what they learned in the
F.) Boring Tools lesson through answering the quiz.
G.) Holding Tools
H.) Driving Tools D. GENERALIZATION
I.) Portable Power Tools What did you learned about the lesson?
J.) Miscellaneous Tools E. EVALUATION
 Carpentry Materials The students will be going to start taking the
quiz for 30 minutes.
A. References:
Long quiz (20 items)
DepEd TLE Grade 7/8 Carpentry Exploratory
Module 1.9- USLeM (UNIFIED SUPPLEMENTARY Direction: Circle the letter of the best answer.
LEARNING MATERIALS for JUNIOR High School Strictly no erasures.
Learners
1. What is the carpentry tool that smoothen
B. Tool and Materials: metal and wood surfaces?
Laptop, projector, internet connection, module, A. Oil Stone B. Files
and video clips C. Paint Brush D. Saw Set
2. What tool that is used to apply paint or
III. IMPLEMENTING STRATEGIES (Procedure) vanish on wood surfaces?
A. PREPARATION A. Oil Stone B. Files
1. Daily Routine C. Paint Brush D. Saw Set
Greetings, Prayer, checking of 3. What is the material hat is used to sawn
attendance timber?
2. Review of the Past Lesson A. Lumber C. Screws
The teacher will give time to students B. Nails D. Hinge
to review the lesson for 10 minutes. 4. What is the material that is used to hold
4. Motivation together two adjoining objects, such as a door
and frame where they are most often used?
A. Lumber C. Screws A. Drill B. Spoke Shave
B. Nails D. Hinge C. Circular Saw D. Router
5. What is the material that is a mechanism 19. The surface of the wood needs to be
used to open or close a door? smoothened. What tool is used to smoothen
A. Lock and Key C. Door Latches surfaces of objects?
B. Door Catches D. Knobs and Handles A. Router B. Jigsaw
C. File D. Sander
6. What is the tool that layout or mark cutting 20. Almost done, what does John need for the
lines? finishing of the project?
A. Compass B. Marking Gauge A. Water B. Varnish
C. Pencil D. Chalk Line C. Paint D. Any of the choices
7. What tool is use to make simple
measurements? KEY TO CORRECTION:
A. Caliper B. Try-Square 1. B- Files
C. Meter Stick D. Ruler 2. C- Paint Brush
8. What is the tool that is use for testing vertical 3. A- Lumber
and horizontal surfaces? 4. D- Hinge
A. Try Square C. Plumb Bob 5. D- Knobs and Handles
B. Spirit Level D. Steel Square 6. C- Pencil
9. What is the tool that is used to obtain a 7. D- Ruler
smooth and flat surface? 8. B- Spirit Level
A. Cabinet Scraper C. Chisel 9. B- Plane
B. Plane D. Spoke Shave 10. C- Plumb Bomb
10. What is the tool that is used to find a 11. B- Cross cut saw
vertical reference to a line? 12. A- Auger Bit
A. Steel Square C. Plumb Bob 13. C- Claw Hammer
B. Spirit Level D. Try Square 14. C- C-clamp
11. What is the carpentry tool that smoothen 15. A- Router
metal and wood surfaces? 16.A- Tools
A. Rip saw B. Cross cut saw 17.B- Materials
C. Compass saw D. Tuming saw 18.C- Circular Saw
12. What tool is used to make hole in woods? 19. D- Sander
A. auger bit B. Expansive bit 20. D- Any of the choices
C. Drill bit D. fish bit IV. AGREEMENT
13. What is the tool that is used to drive and Students will be going to see the result of their
pull out nails on wooden surfaces? quiz once it is checked.
A. Bench Vise C. Claw Hammer
B. Mallet D. Nail Set
14. What is the tool that is used to hold
together pieces of lumber while working?
A. clamp C. C-clamp
B. bar clamp D. Bench vise
15. What is the tool that is used to shape
surfaces and edges of furniture parts?
A. Router C. Jigsaw
B. Electrical Drill D. Circular saw
16. These are the non-consumable items used
in the process. These are mostly carried and
manipulated by hand.
A. Tools B. Materials
C. Hardware D.Equipment
17. These are the items that are being
consumed and may run out while being used in
the process.
A. Tools B. Materials
C. Hardware D.Equipment
18. The stab of wood needs to be shaped into a
round one. What tool is needed to make a
rectangular slab of wood into a round one?