Version 2.

5 1

Technical Note – SunSpec Logging in SolarEdge Inverters

Version History

Version 2.5 (November 2022):

• Synergy inverter-related updates
• Multiple MPPT Inverter Extension Model table: Value at address 40127 changed to 0 (not supported)
Version 2.4 (December 2021): Updated Use Cases for MODBUS over TCP – Multiple Inverter Connection

Version 2.3 (February 2021): Updated Modbus Register Mappings

Version 2.2 (December 2020): Updated Modbus Register Mappings

Version 2.1 (September 2020): New multiple MPPT inverter extension model for Synergy inverters

Version 2.0 (January 2019):

• Addition of SetApp information
• Addition of Modbus over TCP option
• Addition of reference to inverter upgrade procedure
• Addition of Appendix C – Encoding and Decoding 32-bit Values in Modbus.
Version 1.0 (2016) – Initial Release

Contents
Technical Note – SunSpec Logging in SolarEdge Inverters ........................................................................................................................................................ 1

Overview .................................................................................................................................................................................................................................................................. 2

SunSpec Supported Inverters ......................................................................................................................................................................................................................... 3

Use Cases for MODBUS over RS485 ............................................................................................................................................................................................................ 3

Use Cases for MODBUS over TCP................................................................................................................................................................................................................. 7

SolarEdge Device Configuration – Using SetApp ................................................................................................................................................................................ 10

SolarEdge Device Configuration – Using the Inverter/Commercial Gateway Display (LCD) ............................................................................................. 12

Register Mapping – Monitoring Data ....................................................................................................................................................................................................... 15

Multiple MPPT Inverter Extension Model ................................................................................................................................................................................................ 18

Meter Models ...................................................................................................................................................................................................................................................... 20

Appendix A – Supported MODBUS Request Methods ...................................................................................................................................................................... 31

Appendix B – Response Time Information ............................................................................................................................................................................................. 32

Appendix C – Encoding and Decoding 32-bit Values in Modbus ................................................................................................................................................ 33

Support Contact Information ............................................................................................................................................................................................................35

Technical Note – SunSpec Logging in SolarEdge Inverters

2

Overview
SolarEdge inverters support transmission of inverter-level monitoring data directly from the inverter to a local non-SolarEdge device
using the SunSpec open protocol for interoperability between devices in renewable energy systems. This option can be used alongside
the connection to the SolarEdge monitoring server. This document describes the connection method and the protocol and
configurations needed to implement this feature.

Direct connection to a monitoring device is useful when a network connection is unavailable, when extensive custom data processing is
required, or when authorities require direct access to monitoring data.

In many cases, it is possible – and recommended – to employ the direct connection alongside a SolarEdge monitoring platform
connection. Connection to the monitoring platform enables all the monitoring benefits, primarily:

Proactive installer maintenance and real time troubleshooting by SolarEdge support, using with the physical mapping available
only in the monitoring platform

Module-level monitoring

Communication Technologies
SolarEdge uses an open, industry-standard communications stack in order to provide efficient messaging between SolarEdge and third-
party devices and applications.

The communications stack components are briefly described below.

SunSpec

SunSpec is an application-layer communications protocol designed to achieve interoperability between Distributed Energy Resource
(DER) components and smart grid applications.

Modbus

Modbus is a serial communications protocol typically used to connect data collection terminals to a centralized processing unit.
SolarEdge products use Modbus to perform SunSpec messaging over two types of physical/link-layer channels:

Modbus RTU: Remote Terminal Unit (RTU) Modbus over a serial RS485 connection

Modbus TCP: Modbus over an Ethernet connection

SolarEdge systems support a single Modbus Leader only – either single Modbus RTU or single Modbus TCP.

Technical Note – SunSpec Logging in SolarEdge Inverters

 3

SunSpec Supported Inverters

Depending on their type, SolarEdge devices may be configured in either of the two ways:

Using SetApp

Using the LCD

All SolarEdge inverters with SetApp configuration are SunSpec-supported.

SolarEdge inverters with the LCD that have Firmware version 3.xxxx and above only are SunSpec-supported.

To check the inverter firmware versions (for inverters with the LCD):

1. Short press the LCD light button until the following screen is displayed:
I D : # # # # # # # # # #

D S P 1 / 2 : x . x x x x / x . x x x x

C P U : 0 0 0 2 . 0 4 9 6

C o u n t r y : X X X X X

2. If required, upgrade to the latest available firmware, as described in

https://www.solaredge.com/sites/default/files/upgrading_an_inverter_using_micro_sd_card.pdf.

Use Cases for MODBUS over RS485

This section describes RS485 options to connect the inverter to a non-SolarEdge monitoring device.

Physical Connection
The connection is performed using an RS485 connector with a twisted pair cable. The transmission mode in SolarEdge inverters is set to
RTU (binary).

The COM port default properties are: 115200 bps, 8 data bits, no parity, 1 stop bit, no flow control. Baud rate can be changed between
9600bps to 115200bps (supported from CPU version 2.0549).

The RS485 bus can be configured to support connection either to a non-SolarEdge monitoring device or Leader-Follower connection
between SolarEdge inverters. Therefore, a Follower inverter cannot communicate simultaneously with a Leader inverter and with a non-
SolarEdge monitoring device on the same RS485 bus.

All SolarEdge inverters with SetApp configuration have two built-in RS485 ports. An inverter can act as Leader on both ports
simultaneously. Each port on a leader inverter can connect to up to 31 follower inverters. The two ports therefore support connectivity
with 62 follower inverters.

A Commercial Gateway with LCD can act as Leader on one of the built-in RS485 ports and on the RS485 Plug-in.

For more information on the RS485 Plug-in, see:

https://www.solaredge.com/sites/default/files/RS485_expansion_kit_installation_guide.pdf

NOTE
For connectivity purposes, the Synergy Manager is considered a single inverter.

Technical Note – SunSpec Logging in SolarEdge Inverters

4

Single Inverter Connection

Use the RS485 bus for connecting to a non-SolarEdge monitoring device.

Use the Ethernet connection or any of the optional wireless connection options to connect to the SolarEdge monitoring platform.

Multiple Inverter Connection

If a second RS485 port is required to establish connection, use:

RS485-2 for inverters with SetApp configuration

RS485-E (requires a RS485 Plug-in) for inverters with an LCD

Connection to a non-SolarEdge monitoring device only (without connection to the monitoring platform)

Option 1 (direct connection) – Use RS485-1 to connect Followers to the Leader and the Leader to a non-SolarEdge monitoring device.
Every inverter in the RS485 bus should be configured to a different device ID (MODBUS ID).

Option 2 – Use RS485-1 to connect Follower inverters to the Leader; use either RS485-2 or RS485-E to connect the Leader to a non-
SolarEdge monitoring device. Every inverter in the RS485 bus should be configured to a different device ID (MODBUS ID).

Technical Note – SunSpec Logging in SolarEdge Inverters

 5

Connection to a non-SolarEdge monitoring device (with connection to the monitoring platform)

Use the RS485 bus for connection to a non-SolarEdge monitoring device. Every inverter in the RS485 bus should be configured to a
different device ID (MODBUS ID).

Option 1 (direct connection) – Connect each inverter to the router via Ethernet cables.

Option 2 – Connect the router to one inverter only.

Technical Note – SunSpec Logging in SolarEdge Inverters

6

Connection to the monitoring platform and to a non-SolarEdge monitoring device using a Commercial
Gateway

Use the RS485-2 bus for connection to a non-SolarEdge monitoring device. Every inverter connected to the RS485 bus should be
configured to a different device ID (MODBUS ID).

If required, use the RS485-E bus for connecting a second chain of inverters.

Technical Note – SunSpec Logging in SolarEdge Inverters

 7

Use Cases for MODBUS over TCP

This section describes MODBUS over TCP options to connect the inverter to a non-SolarEdge monitoring device.

Single Inverter Connection

Use Ethernet for connecting to a non-SolarEdge monitoring device.

Multiple Inverter Connection

Connection to a non-SolarEdge monitoring device only (without connection to the SolarEdge monitoring
platform)

Use Ethernet for connection to a non-SolarEdge monitoring device.

Technical Note – SunSpec Logging in SolarEdge Inverters

8

Connection to a non-SolarEdge monitoring device (with connection to the SolarEdge monitoring

platform)

Use Ethernet for connection to a non-SolarEdge monitoring device.

Option 1 (direct connection) – Connect each inverter to the Ethernet router via Ethernet cables.

Option 2 – Connect the Leader only to the Ethernet router via Ethernet cables.

Connect a second chain of the inverters to the Leader inverter using RS485-2/RS485-E.

Technical Note – SunSpec Logging in SolarEdge Inverters

 9

Connection to the SolarEdge monitoring platform and to a non-SolarEdge monitoring device using a
Commercial Gateway

Use Ethernet for connection to a non-SolarEdge monitoring device. Every inverter connected to the RS485 bus should be configured to
a different device ID (MODBUS ID).

If required, use the RS485-E bus for connecting a second chain of inverters.

Technical Note – SunSpec Logging in SolarEdge Inverters

10

SolarEdge Device Configuration – Using SetApp

This section describes how to configure a SolarEdge device (inverter or Commercial Gateway) to be monitored by a non-SolarEdge
monitoring device using SetApp.

NOTE
The actual SetApp configuration procedures may differ from the ones shown in this document.

To reach the main setup menu, access SetApp and tap Commissioning  Site Communication:

Modbus over RS485 Configuration

To configure the inverters (when used without the Commercial Gateway):

1. Under the Site Communication menu, set the following:

• RS485-1  Protocol  SunSpec (Non-SE Logger)

• RS485-1  Device ID, and enter the MODBUS address (a unique value 1…247). This will set the register C_DeviceAddress.
2. If needed, set the baud rate to a preferred value: RS485-1  Baud rate and enter the rate.

To configure the inverters and gateway (when used with the Commercial Gateway):

1. Inverter configuration: For all inverters, verify the following RS485 bus settings under the Site Communication menu:

• RS485-1  Protocol  SolarEdge  SolarEdge Follower

• RS485-1  Device ID  [a unique value 1…247]
2. Commercial Gateway configuration using the device display: Use RS485-1 to connect to the inverters. RS485-1 bus configuration is
as follows:

• Communication  RS485-1 Conf  Device Type  SolarEdge

• Communication  RS485-1 Conf  Protocol  Leader
• Communication  RS485-1 Conf  Follower Detect
The Commercial Gateway should report the correct number of Follower inverters. If it does not, verify the connections and
terminations.

3. Use RS485-2 to connect the Commercial Gateway to the non-SolarEdge monitoring device. Configure the RS485-2 bus settings as
follows, using the device display:

• Communication  RS485-2 Conf  Protocol  SunSpec (Non-SE Logger)

The Commercial Gateway device ID is irrelevant for communications, but needs to be set to a different ID than the one set for
the inverters.
• Communication  RS485-2 Conf  Device ID  [use one of the higher IDs (e.g. 247) to make sure it is out of scope]
• The default baud rate is 115200 bps. If a different baud rate is required, select: Communication  RS485-2 Conf  Baud
Rate

4. Make sure the device ID of the non-SolarEdge monitoring device is different from all other device IDs configured in the inverters
and gateways.

Technical Note – SunSpec Logging in SolarEdge Inverters

 11

5. Connect the Commercial Gateway to router via the Ethernet interface and configure the following settings using the device display:

• Communication  Server  LAN

• Communication  LAN Conf  Set DHCP  [Select Enable for DHCP or Disable for static IP configuration]
For Static DHCP setting, configure as follows:
• Communication  LAN Conf  Set IP  [Set inverters’ IP]
• Communication  LAN Conf  Set Mask  [Set inverters’ subnet mask]
• Communication  LAN Conf  Set Gateway  [Set inverters’ gateway]
• Communication  LAN Conf  Set DNS  [Set inverters’ DNS]
6. If the router is connected to the server, select Commissioning  Status and verify that “S_OK” is displayed on the Status page.

MODBUS over TCP Support

MODBUS/TCP uses the Ethernet media in physical layers to carry the MODBUS message handling structure and can support a large
number of devices in one network; it is easier to integrate into the Local Area Network (LAN) of a company, so it is the choice of more
and more customers.

Here, it is used for remote 3rd party monitoring and control. MODBUS TCP is agnostic of the server connection. It works only over LAN.
When configured, MODBUS TCP does not initiate a connection - the server waits for a client to connect. Only one connection is
supported.
NOTE
The MODBUS TCP function is disabled by default. When enabled, it supports TCP port 1502 by default. Port
number can be reconfigured.

MODBUS over TCP Configuration

To setup MODBUS TCP:

1. Select Site Communication  Modbus TCP  Enable. A new Port menu is added to the screen (the default port is 1502)

2. To modify the TCP port, select Port, set the port number and tap Done.

3. NOTE
The default device ID of the inverter connected to the Ethernet is 1.

NOTE
The TCP server idle time is 2 minutes. In order to leave the connection open, the request should be made
within 2 minutes. The connection can remain open without any MODBUS requests.

Technical Note – SunSpec Logging in SolarEdge Inverters

12

SolarEdge Device Configuration – Using the Inverter/Commercial Gateway Display (LCD)

This section describes how to configure a SolarEdge device (inverter or Commercial Gateway) to be monitored by a non-SolarEdge
monitoring device using the LCD. To reach the main setup menu, follow the instructions in the Installation Guide of the specific
SolarEdge device.

Modbus over RS485 Configuration

To configure the inverters (when used without the Commercial Gateway):

1. Under the Communication menu, set the following:

• Communication  Server  Select any server connection, except for RS485 (if the inverter is not connected to the
SolarEdge monitoring platform, select None.
• Communication  RS485-1 Conf
• RS485-1 Conf  Device Type  Non-SE Logger
• RS485-1 Conf  Protocol  SunSpec
• RS485-1 Conf  Device ID and enter the MODBUS address (a unique value 1…247). This will set the register
C_DeviceAddress.
2. If needed, set the baud rate to a preferred value: RS485-1 Conf  Baud rate and enter the rate.

To configure the inverter (when used with the Commercial Gateway):

1. Inverters configuration: For all inverters, set the following RS485 bus settings:

• Communication  RS485-1 Conf  Device Type  SolarEdge

• Communication  RS485-1 Conf  Protocol Slave
• Communication  RS485-1 Conf  Device ID  [a unique value 1…247]
2. Commercial Gateway configuration: Use RS485-1 to connect to the inverters. RS485-1 bus configuration is as follows:

• Communication  RS485-1 Conf Device Type  SolarEdge

• Communication  RS485-1 Conf  Protocol  Master
• Communication  RS485-1 Conf  Slave Detect
The Commercial Gateway should report the correct number of slaves. If it does not, verify the connections and terminations.

Technical Note – SunSpec Logging in SolarEdge Inverters

 13

3. Use RS485-2 to connect to the non-SolarEdge monitoring device. RS485-2 bus configuration is as follows:

• Communication  RS485-2 Conf  Device Type Non-SE Logger

• Communication  RS485-2 Conf  Protocol SunSpec
The Commercial Gateway Device ID is irrelevant for communications, but needs to be set to a different ID than the one set for
the inverters.
• Communication  RS485-2 Conf  Device ID  [use one of the higher ID’s (e.g. 247) to make sure it is out of scope]
• The default baud rate is 115200 bps. If a different baud rate is required, select: Communication  RS485-2 Conf  Baud
Rate
4. Make sure the device ID of the non-SolarEdge monitoring device is different from all other device IDs configured in the inverters
and gateways.

5. Connect the Commercial Gateway to router via the Ethernet interface and configure the following settings:

• Communication  Server  LAN

• Communication  LAN Conf  Set DHCP  [Select Enable for DHCP or Disable for static IP configuration]
For Static DHCP setting, configure as follows:
• Communication  LAN Conf  Set IP  [Set inverters’ IP]
• Communication  LAN Conf  Set Mask  [Set inverters’ subnet mask]
• Communication  LAN Conf  Set Gateway  [Set inverters’ gateway]
• Communication  LAN Conf  Set DNS  [Set inverters’ DNS]
6. If the router is connected to the server, verify that the LCD panel displays <S_OK>.

7. Verify that the LCD panel of all inverters is <S_OK>.

Technical Note – SunSpec Logging in SolarEdge Inverters

14

MODBUS over TCP Support

MODBUS/TCP uses the Ethernet media in physical layers to carry the MODBUS message handling structure and can support a large
number of devices in one network; it is easier to integrate into the Local Area Network (LAN) of a company, so it is the choice of more
and more customers.

Here, it is used for remote 3rd party monitoring and control. MODBUS TCP is agnostic of the server connection. It works only over LAN.
When configured, MODBUS TCP does not initiate a connection. The server waits for a client to connect. Only one connection is
supported.

NOTE
The MODBUS TCP function is disabled by default. When enabled, it supports TCP port 502 by default. The port number
can be reconfigured.

MODBUS over TCP Configuration

To setup MODBUS TCP:

• Select Communication  LAN Conf  Modbus TCP (the default port is 502).
To modify the TCP port, select Modbus TCP  TCP Port, set the port number and long-press Enter.
NOTE
The default device ID of the inverter connected to the Ethernet is 1.

When the MODBUS TCP feature is enabled, the following information is displayed:

Status:
• Init – Initializing server – This state only occurs after the first configuration until it reaches the ready status. This activity
lasts about 10sec.
• Ready – The server is up and waiting for a client to connect.
• Connected – The client is connected.
• Failed – The server is unable to accept clients (see error message).
Error messages:
• Disconnected – The Ethernet cable is not connected
• Gateway Ping Failed – A ping to the 1st router failed
• No IP – Either no DHCP configuration or static IP configuration (no DHCP server that assigned an IP address) or need to
define a static IP.
NOTE
The TCP server idle time is 2 minutes. In order to leave the connection open, the request should be made within 2 minutes.
The connection can remain open without any MODBUS requests.

Technical Note – SunSpec Logging in SolarEdge Inverters

 15

Register Mapping – Monitoring Data

This section describes the registers mapping for the inverter monitoring data (read-only MODBUS protocol data). The SolarEdge
inverter mapping for monitoring data is based on the open protocol managed by SunSpec: SunSpec Alliance Interoperability
Specification – Inverter Models v1.0. Refer to the SunSpec Alliance Interoperability Specification – Common Models (Elements)
document for a detailed description of the protocol.

The register mapping can be downloaded from the SunSpec Alliance web page: http://www.sunspec.org/.

SolarEdge inverters support the following mappings:

SunSpec module ID 101, 102 1 and 103 register mappings.

SolarEdge three phase inverters with Synergy technology also support SunSpec module ID 160 register mappings.

Common Model MODBUS Register Mappings

The base Register Common Block is set to 40001 (MODBUS PLC address [base 1]) or 40000 (MODBUS Protocol Address [base 0]).

All parameters are defined as in the SunSpec Common block definition, except for the C_Options register, which is set to
NOT_IMPLEMENTED.

C_Manufacturer is set to SolarEdge.

C_Model is set to the appropriate inverter model, e.g. SE5000.

C_Version contains the CPU software version with leading zeroes, e.g. 0002.0611.

C_SerialNumber contains the inverter serial number.

C_DeviceAddress is the device MODBUS ID.

Address
Size Name Type Description
(base 0) (base 1)
Value = "SunS" (0x53756e53). Uniquely identifies this as a
40000 40001 2 C_SunSpec_ID uint32
SunSpec MODBUS Map
Value = 0x0001. Uniquely identifies this as a SunSpec
40002 40003 1 C_SunSpec_DID uint16
Common Model Block
40003 40004 1 C_SunSpec_Length uint16 65 = Length of block in 16-bit registers
40004 40005 16 C_Manufacturer String(32) Value Registered with SunSpec = "SolarEdge "
40020 40021 16 C_Model String(32) SolarEdge Specific Value
40044 40045 8 C_Version String(16) SolarEdge Specific Value
40052 40053 16 C_SerialNumber String(32) SolarEdge Unique Value
40068 40069 1 C_DeviceAddress uint16 MODBUS Unit ID

1 Supported only in split-phase configurations (Japanese grid and 240V grid in North America)

Technical Note – SunSpec Logging in SolarEdge Inverters

16

Inverter Device Status Values

The following I_Status_* values are supported:
Parameter Value Description
I_STATUS_OFF 1 Off
I_STATUS_SLEEPING 2 Sleeping (auto-shutdown) – Night mode
I_STATUS_STARTING 3 Grid Monitoring/wake-up
I_STATUS_MPPT 4 Inverter is ON and producing power
I_STATUS_THROTTLED 5 Production (curtailed)
I_STATUS_SHUTTING_DOWN 6 Shutting down
I_STATUS_FAULT 7 Fault
I_STATUS_STANDBY 8 Maintenance/setup

Inverter Model MODBUS Register Mappings

The following table lists the supported MODBUS register values.

Unsupported values are indicated by the NOT_IMPLEMENTED value.

The base register of the Device Specific block is set to 40070 (MODBUS PLC address [base 1]), or 40069 (MODBUS Protocol Address
[base 0]).

acc32 is a uint32 accumulator that should always increase. Its value is in the range of 0...4294967295.

Scale Factors. As an alternative to floating point format, values are represented by Integer values with a signed scale factor
applied. The scale factor explicitly shifts the decimal point to left (negative value) or to the right (positive value).

For example, a value “Value” may have an associated value “Value_SF”

Value = “Value” * 10^ Value_SF for example:

• For “Value” = 2071 and “Value_SF” = -2 Value = 2071*10^-2 = 20.71
• For “Value” = 2071 and “Value_SF” = 2 Value = 2071*10^2 = 207100

Address
Size Name Type Units Description
(base 0) (base 1)
40069 40070 1 C_SunSpec_DID uint16 101 = single phase
102 = split phase
103 = three phase
40070 40071 1 C_SunSpec_Length uint16 Registers 50 = Length of model block
40071 40072 1 I_AC_Current uint16 Amps AC Total Current value
40072 40073 1 I_AC_CurrentA uint16 Amps AC Phase A Current value
40073 40074 1 I_AC_CurrentB uint16 Amps AC Phase B Current value
40074 40075 1 I_AC_CurrentC uint16 Amps AC Phase C Current value
40075 40076 1 I_AC_Current_SF int16 AC Current scale factor
40076 40077 1 I_AC_VoltageAB uint16 Volts AC Voltage Phase AB value
40077 40078 1 I_AC_VoltageBC uint16 Volts AC Voltage Phase BC value
40078 40079 1 I_AC_VoltageCA uint16 Volts AC Voltage Phase CA value

Technical Note – SunSpec Logging in SolarEdge Inverters

 17

Address
Size Name Type Units Description
(base 0) (base 1)
40079 40080 1 I_AC_VoltageAN 1 uint16 Volts AC Voltage Phase A to N value
40080 40081 1 I_AC_VoltageBN 1 uint16 Volts AC Voltage Phase B to N value
40081 40082 1 I_AC_VoltageCN 1 uint16 Volts AC Voltage Phase C to N value
40082 40083 1 I_AC_Voltage_SF int16 AC Voltage scale factor
40083 40084 1 I_AC_Power int16 Watts AC Power value
40084 40085 1 I_AC_Power_SF int16 AC Power scale factor
40085 40086 1 I_AC_Frequency uint16 Hertz AC Frequency value
40086 40087 1 I_AC_Frequency_SF int16 Scale factor
40087 40088 1 I_AC_VA int16 VA Apparent Power
40088 40089 1 I_AC_VA_SF int16 Scale factor
40089 40090 1 I_AC_VAR int16 VAR Reactive Power
40090 40091 1 I_AC_VAR_SF int16 Scale factor
40091 40092 1 I_AC_PF int16 % Power Factor
40092 40093 1 I_AC_PF_SF int16 Scale factor
40093 40094 2 I_AC_Energy_WH acc32 WattHours AC Lifetime Energy production
40095 40096 1 I_AC_Energy_WH_SF uint16 Scale factor
40096 40097 1 I_DC_Current uint16 Amps DC Current value
40097 40098 1 I_DC_Current_SF int16 Scale factor
40098 40099 1 I_DC_Voltage uint16 Volts DC Voltage value
40099 40100 1 I_DC_Voltage_SF int16 Scale factor
40100 40101 1 I_DC_Power int16 Watts DC Power value
40101 40102 1 I_DC_Power_SF int16 Scale factor
40103 40104 1 I_Temp_Sink int16 Degrees C Heat Sink Temperature
40106 40107 1 I_Temp_SF int16 Scale factor
40107 40108 1 I_Status uint16 Operating State
40108 40109 1 I_Status_Vendor uint16 Vendor-defined operating state and error
codes. For error description, meaning and
troubleshooting, refer to the SolarEdge
Installation Guide.

1 Supported only in split-phase configurations (Japanese grid and 240V grid in North America).

Technical Note – SunSpec Logging in SolarEdge Inverters

18

Multiple MPPT Inverter Extension Model

The Multiple MPPT (Maximum Power Point Tracker) Inverter Extension Model (160) is supported for SolarEdge Synergy Inverters with
firmware version 4.13.xx or later. The fixed block data below refers to an entire Synergy Manager system (and not to individual blocks
within the system).

Address Name Size Type Units Description

(base 0) (base 1)
Header (Size: 2 words)
40121 40122 ID 1 uint16 N/A Value = 160
Multiple MPPT Inverter Extension Model
40122 40123 L 1 uint16 N/A Model length
Fixed Block (Size: 8 words)
40123 40124 DCA_SF 1 sunssf N/A Current Scale Factor
40124 40125 DCV_SF 1 sunssf Voltage Scale Factor
40125 40126 DCW_SF 1 sunssf Power Scale Factor
40126 40127 DCWH_SF 1 sunssf 0 (not supported)
40127 40128 Evt 2 bitfield32 0 (not supported)
40129 40130 N 1 count Number of Synergy units (2 or 3)
40130 40131 TmsPer 1 uint16 0 (not supported)
Synergy Unit 0 Block (Size: 20 words)
40131 40132 ID 1 uint16 Synergy Unit #0
40132 40133 IDStr 8 string Input ID String
40140 40141 DCA 1 uint16 DC Current (A)
40141 40142 DCV 1 uint16 DC Voltage (V)
40142 40143 DCW 1 uint16 DC Power (W)
40143 40144 DCWH 2 acc32 0 (not supported)
40145 40146 Tms 2 uint32 0 (not supported)
40147 40148 Tmp 1 int16 Temperature (oC)
40148 40149 DCSt 1 enum16 0 (not supported)
40149 40150 DCEvt 2 bitfield32 0 (not supported)
Synergy Unit 1 Block (Size: 20 words)
40151 40152 ID 1 uint16 Synergy Unit #1
40152 40153 IDStr 8 string Input ID String
40160 40161 DCA 1 uint16 DC Current (A)
40161 40162 DCV 1 uint16 DC Voltage (V)
40162 40163 DCW 1 uint16 DC Power (W)
40163 40164 DCWH 2 acc32 0 (not supported)
40165 40166 Tms 2 uint32 0 (not supported)
40167 40168 Tmp 1 int16 Temperature (oC)
40168 40169 DCSt 1 enum16 0 (not supported)
40169 40170 DCEvt 2 bitfield32 0 (not supported)

Technical Note – SunSpec Logging in SolarEdge Inverters

 19

Address Name Size Type Units Description

(base 0) (base 1)
Synergy Unit 2 Block (Size: 20 words)
40171 40172 ID 1 uint16 Synergy Unit #2
40172 40173 IDStr 8 string Input ID String
40180 40181 DCA 1 uint16 DC Current (A)
40181 40182 DCV 1 uint16 DC Voltage (V)
40182 40183 DCW 1 uint16 DC Power (W)
40183 40184 DCWH 2 acc32 0 (not supported)
40185 40186 Tms 2 uint32 0 (not supported)
40187 40188 Tmp 1 int16 Temperature (oC)
40188 40189 DCSt 1 enum16 0 (not supported)
40189 40190 DCEvt 2 bitfield32 0 (not supported)

Global Events (Evt)

The following table contains a list of enumerated global event types. Field type is bitfield32:

# Name Description
0 GROUND_FAULT Ground Fault
1 INPUT_OVER_VOLTAGE Input Over Voltage
3 DC_DISCONNECT DC Disconnect
5 CABINET_OPEN Cabinet Open
6 MANUAL_SHUTDOWN Manual Shutdown
7 OVER_TEMP Over Temperature
12 BLOWN_FUSE Blown Fuse
13 UNDER_TEMP Under Temperature
14 MEMORY_LOSS Memory Loss
15 ARC_DETECTION Arc Detection
19 RESERVED Reserved
20 TEST_FAILED Test Failed
21 INPUT_UNDER_VOLTAGE Under Voltage
22 INPUT_OVER_CURRENT Over Current

Technical Note – SunSpec Logging in SolarEdge Inverters

20

Meter Models
The SunSpec Alliance Interoperability Specification describes the data models and MODBUS register mappings for meter devices used
in Renewable Energy systems. This section defines the models for:
Single Phase Meter
Split Phase Meter
WYE (4-wire) Meter
Delta (3-wire)Meter

Meter Device Block

The following data elements are provided to describe meters.
C_SunSpec_DID – A well-known value that uniquely identifies this block as a meter
block. (4) for single phase meters and (5) for three phase meter types.
C_SunSpec_Length – The length of the meter block in registers.
M_AC_xxxx – Meter AC values.
M_Exported_xxxx – Meter Exported Energy values
M_Imported_xxxx – Meter Imported Energy values

Energy Value

The energy value is represented by a 32-bit unsigned integer accumulator with a scale factor. Values for import and export are provided.
Unsupported or invalid accumulators may return 0x00000000. Power signs and Energy quadrants are per IEEE 1459-2000.

Meter Event Flag Values

The SunSpec Common Elements defines a C_Event value. The meter specific flags are defined here.

C_Event Value Flag Description

M_EVENT_Power_Failure 0x00000004 Loss of power or phase
M_EVENT_Under_Voltage 0x00000008 Voltage below threshold (Phase Loss)
M_EVENT_Low_PF 0x00000010 Power Factor below threshold (can indicate miss-associated voltage and
current inputs in three phase systems)

M_EVENT_Over_Current 0x00000020 Current Input over threshold (out of measurement range)

M_EVENT_Over_Voltage 0x00000040 Voltage Input over threshold (out of measurement range)
M_EVENT_Missing_Sensor 0x00000080 Sensor not connected
M_EVENT_Reserved1 0x00000100 Reserved for future use
M_EVENT_Reserved2 0x00000200 Reserved for future use
M_EVENT_Reserved3 0x00000400 Reserved for future use
M_EVENT_Reserved4 0x00000800 Reserved for future use
M_EVENT_Reserved5 0x00001000 Reserved for future use
M_EVENT_Reserved6 0x00002000 Reserved for future use
M_EVENT_Reserved7 0x00004000 Reserved for future use
M_EVENT_Reserved8 0x00008000 Reserved for future use
M_EVENT_OEM1-15 0x7FFF000 Reserved for OEMs

Technical Note – SunSpec Logging in SolarEdge Inverters

 21

MODBUS Register Mappings

Meter Model – MODBUS Mapping

This map supports single, split, wye, and delta meter connections in a single map as proper subsets. The connection type is
distinguished by the C_SunSpec_DID. Registers that are not applicable to a meter class return the unsupported value (for example,
Single Phase meters will support only summary and phase A values).

NOTE
Modbus registers store data in "Big Endian" format. Most-significant values are stored first, at the lowest storage address.

The meters’ base address is calculated as shown in the table below:

For 2-unit three phase inverters with Synergy technology, add 50 to the default addresses.

For 3-unit three phase inverters with Synergy technology, add 70 to the default addresses.

Address Address Address

(Default) (using 2-unit Synergy) (using 3-unit Synergy)
Meter # (base 0) (base 1) (base 0) (base 1) (base 0) (base 1)
1st meter 40000 + 121 40000 + 122 40000 + 171 40000 + 172 40000 + 191 40000 + 192
2nd meter 40000 + 295 40000 + 296 40000 + 345 40000 + 346 40000 + 365 40000 + 366
3rd meter 40000 + 469 40000 + 470 40000 + 519 40000 + 520 40000 + 539 40000 + 540

NOTE
Only enabled meters are readable, i.e. if meter 1 and 3 are enabled, they are readable as 1st meter and 2nd meter (and the
3rd meter isn't readable). The meter type can be read from the Common block Options field (the same strings that we use
in the menus).

Meter 1

Address Size Name Type Units Description

(base 0) (base 1)
Common Block
40121 40122 1 C_SunSpec_DID uint16 N/A Value = 0x0001. Uniquely identifies this as a
SunSpec Common Model Block
40122 40123 1 C_SunSpec_Length uint16 N/A 65 = Length of block in 16-bit registers
40123 40124 16 C_Manufacturer String(32) N/A Meter manufacturer
40139 40140 16 C_Model String(32) N/A Meter model
40155 40156 8 C_Option String(16) N/A Export + Import, Production, consumption,
40163 40164 8 C_Version String(16) N/A Meter version
40171 40172 16 C_SerialNumber String(32) N/A Meter SN
40187 40188 1 C_DeviceAddress uint16 N/A Inverter Modbus ID

Technical Note – SunSpec Logging in SolarEdge Inverters

22

Identification
40188 40189 1 C_SunSpec_DID uint16 N/A Well-known value. Uniquely identifies this as a
SunSpec MODBUS Map:
 Single Phase (AN or AB) Meter (201)
 Split Single Phase (ABN) Meter (202)
 Wye-Connect Three Phase (ABCN) Meter (203)
 Delta-Connect Three Phase (ABC) Meter(204)
40189 40190 1 C_SunSpec_Length uint16 Registers Length of meter model block
Current
40190 40191 1 M_AC_Current int16 Amps AC Current (sum of active phases)
40191 40192 1 M_AC_Current_A int16 Amps Phase A AC Current
40192 40193 1 M_AC_Current_B int16 Amps Phase B AC Current
40193 40194 1 M_AC_Current_C int16 Amps Phase C AC Current
40194 40195 1 M_AC_Current_S F int16 SF AC Current Scale Factor
Voltage
Line to Neutral Voltage
40195 40196 1 M_AC_Voltage_L N int16 Volts Line to Neutral AC Voltage (average of active phases)
40196 40197 1 M_AC_Voltage_A N int16 Volts Phase A to Neutral AC Voltage
40197 40198 1 M_AC_Voltage_B N int16 Volts Phase B to Neutral AC Voltage
40198 40199 1 M_AC_Voltage_C N int16 Volts Phase C to Neutral AC Voltage
Line to Line Voltage
40199 40200 1 M_AC_Voltage_L L int16 Volts Line to Line AC Voltage (average of active phases)
40200 40201 1 M_AC_Voltage_A B int16 Volts Phase A to Phase B AC Voltage
40201 40202 1 M_AC_Voltage_B C int16 Volts Phase B to Phase C AC Voltage
40202 40203 1 M_AC_Voltage_C A int16 Volts Phase C to Phase A AC Voltage
40203 40204 1 M_AC_Voltage_S F int16 SF AC Voltage Scale Factor
Frequency
40204 40205 1 M_AC_Freq int16 Herts AC Frequency
40205 40206 1 M_AC_Freq_SF int16 SF AC Frequency Scale Factor

Technical Note – SunSpec Logging in SolarEdge Inverters

 23

Power
Real Power
40206 40207 1 M_AC_Power int16 Watts Total Real Power (sum of active phases)
40207 40208 1 M_AC_Power_A int16 Watts Phase A AC Real Power
40208 40209 1 M_AC_Power_B int16 Watts Phase B AC Real Power
40209 40210 1 M_AC_Power_C int16 Watts Phase C AC Real Power
40210 40211 1 M_AC_Power_SF int16 SF AC Real Power Scale Factor
Apparent Power
40211 40212 1 M_AC_VA int16 Volt- Amps Total AC Apparent Power (sum of active phases)
40212 40213 1 M_AC_VA_A int16 Volt- Amps Phase A AC Apparent Power
40213 40214 1 M_AC_VA_B int16 Volt- Amps Phase B AC Apparent Power
40214 40215 1 M_AC_VA_C int16 Volt- Amps Phase C AC Apparent Power
40215 40216 1 M_AC_VA_SF int16 SF AC Apparent Power Scale Factor
Reactive Power
40216 40217 1 M_AC_VAR int16 VAR Total AC Reactive Power (sum of active phases)
40217 40218 1 M_AC_VAR_A int16 VAR Phase A AC Reactive Power
40218 40219 1 M_AC_VAR_B int16 VAR Phase B AC Reactive Power
40219 40220 1 M_AC_VAR_C int16 VAR Phase C AC Reactive Power
40220 40221 1 M_AC_VAR_SF int16 SF AC Reactive Power Scale Factor
Power Factor
40221 1 M_AC_PF int16 % Average Power Factor (average of active
40222
phases)
40222 40223 1 M_AC_PF_A int16 % Phase A Power Factor
40223 40224 1 M_AC_PF_B int16 % Phase B Power Factor
40224 40225 1 M_AC_PF_C int16 % Phase C Power Factor
40225 40226 1 M_AC_PF_SF int16 SF AC Power Factor Scale Factor
Accumulated Energy
Real Energy
40226 40227 2 M_Exported uint32 Watt- hours Total Exported Real Energy
40228 40229 2 M_Exported_A uint32 Watt- hours Phase A Exported Real Energy
40230 40231 2 M_Exported_B uint32 Watt- hours Phase B Exported Real Energy
40232 40233 2 M_Exported_C uint32 Watt- hours Phase C Exported Real Energy
40234 40235 2 M_Imported uint32 Watt- hours Total Imported Real Energy
40236 40237 2 M_Imported_A uint32 Watt- hours Phase A Imported Real Energy
40238 40239 2 M_Imported_B uint32 Watt- hours Phase B Imported Real Energy
40240 40241 2 M_Imported_C uint32 Watt- hours Phase C Imported Real Energy
40242 40243 1 M_Energy_W_SF int16 SF Real Energy Scale Factor

Technical Note – SunSpec Logging in SolarEdge Inverters

24

Apparent Energy
40243 40244 2 M_Exported_VA uint32 VA-hours Total Exported Apparent Energy
40245 40246 2 M_Exported_VA_ A uint32 VA-hours Phase A Exported Apparent Energy
40247 40248 2 M_Exported_VA_ B uint32 VA-hours Phase B Exported Apparent Energy
40249 40250 2 M_Exported_VA_ C uint32 VA-hours Phase C Exported Apparent Energy
40251 40252 2 M_Imported_VA uint32 VA-hours Total Imported Apparent Energy
40253 40254 2 M_Imported_VA_ A uint32 VA-hours Phase A Imported Apparent Energy
40255 40256 2 M_Imported_VA_ B uint32 VA-hours Phase B Imported Apparent Energy
40257 40258 2 M_Imported_VA_ C uint32 VA-hours Phase C Imported Apparent Energy
40259 40260 1 M_Energy_VA_S F int16 SF Apparent Energy Scale Factor
Reactive Energy
40260 40261 2 M_Import_VARh_ Q1 uint32 VAR-hours Quadrant 1: Total Imported Reactive Energy
40262 40263 2 M_Import_VARh_ Q1A uint32 VAR-hours Phase A - Quadrant 1: Imported Reactive Energy
40264 40265 2 M_Import_VARh_ Q1B uint32 VAR-hours Phase B- Quadrant 1: Imported Reactive Energy
40266 40267 2 M_Import_VARh_ Q1C uint32 VAR-hours Phase C- Quadrant 1: Imported Reactive Energy
40268 40269 2 M_Import_VARh_ Q2 uint32 VAR-hours Quadrant 2: Total Imported Reactive Energy
40270 40271 2 M_Import_VARh_ Q2A uint32 VAR-hours Phase A - Quadrant 2: Imported Reactive Energy
40272 40273 2 M_Import_VARh_ Q2B uint32 VAR-hours Phase B- Quadrant 2: Imported Reactive Energy
40274 40275 2 M_Import_VARh_ Q2C uint32 VAR-hours Phase C- Quadrant 2: Imported Reactive Energy
40276 40277 2 M_Export_VARh_ Q3 uint32 VAR-hours Quadrant 3: Total Exported Reactive Energy
40278 40279 2 M_Export_VARh_ Q3A uint32 VAR-hours Phase A - Quadrant 3: Exported Reactive Energy
40280 40281 2 M_Export_VARh_ Q3B uint32 VAR-hours Phase B- Quadrant 3: Exported Reactive Energy
40282 40283 2 M_Export_VARh_ Q3C uint32 VAR-hours Phase C- Quadrant 3: Exported Reactive Energy
40284 40285 2 M_Export_VARh_ Q4 uint32 VAR-hours Quadrant 4: Total Exported Reactive Energy
40286 40287 2 M_Export_VARh_ Q4A uint32 VAR-hours Phase A - Quadrant 4: Exported Reactive Energy
40288 40289 2 M_Export_VARh_ Q4B uint32 VAR-hours Phase B- Quadrant 4: Exported Reactive Energy
40290 40291 2 M_Export_VARh_ Q4C uint32 VAR-hours Phase C- Quadrant 4: Exported Reactive Energy
40292 40293 1 M_Energy_VAR_ SF int16 SF Reactive Energy Scale Factor
Events
40293 40294 2 M_Events uint32 Flags See M_EVENT_ flags. 0 = nts.

Technical Note – SunSpec Logging in SolarEdge Inverters

 25

Meter 2

Address Size Name Type Units Description

(base 0) (base 1)
Common Block
40295 40296 1 C_SunSpec_DID uint16 N/A Value = 0x0001. Uniquely identifies this as a
SunSpec Common Model Block
40296 40297 1 C_SunSpec_Length uint16 N/A 65 = Length of block in 16-bit registers
40297 40298 16 C_Manufacturer String(32) N/A Meter manufacturer
40313 40314 16 C_Model String(32) N/A Meter model
40329 40330 8 C_Option String(16) N/A Export+Import, Production, Consumption,

40337 40338 8 C_Version String(16) N/A Meter version

40345 40346 16 C_SerialNumber String(32) N/A Meter SN

40361 40362 1 C_DeviceAddress uint16 N/A Inverter Modbus ID
Identification
40362 40363 1 C_SunSpec_DID uint16 N/A Well-known value. Uniquely identifies this as a
SunSpec MODBUS Map:
 Single Phase (AN or AB) Meter (201)
 Split Single Phase (ABN) Meter (202)
 Wye-Connect Three Phase (ABCN) Meter (203)
 Delta-Connect Three Phase (ABC) Meter(204)
40363 40364 1 C_SunSpec_Length uint16 Registers Length of meter model block
Current
40364 40365 1 M_AC_Current int16 Amps AC Current (sum of active phases)

40365 40366 1 M_AC_Current_A int16 Amps Phase A AC Current

40366 40367 1 M_AC_Current_B int16 Amps Phase B AC Current

40367 40368 1 M_AC_Current_C int16 Amps Phase C AC Current

40368 40369 1 M_AC_Current_S F int16 SF AC Current Scale Factor

Voltage
Line to Neutral Voltage
40369 40370 1 M_AC_Voltage_L N int16 Volts Line to Neutral AC Voltage (average of active
phases)
40370 40371 1 M_AC_Voltage_A N int16 Volts Phase A to Neutral AC Voltage

40371 40372 1 M_AC_Voltage_B N int16 Volts Phase B to Neutral AC Voltage

40372 40373 1 M_AC_Voltage_C N int16 Volts Phase C to Neutral AC Voltage

Line to Line Voltage

40373 40374 1 M_AC_Voltage_L L int16 Volts Line to Line AC Voltage (average of active phases)
40374 40375 1 M_AC_Voltage_A B int16 Volts Phase A to Phase B AC Voltage
40375 40376 1 M_AC_Voltage_B C int16 Volts Phase B to Phase C AC Voltage
40376 40377 1 M_AC_Voltage_C A int16 Volts Phase C to Phase A AC Voltage
40377 40378 1 M_AC_Voltage_S F int16 SF AC Voltage Scale Factor

Technical Note – SunSpec Logging in SolarEdge Inverters

26

Frequency
40378 40379 1 M_AC_Freq int16 Herts AC Frequency
40379 40380 1 M_AC_Freq_SF int16 SF AC Frequency Scale Factor
Power
Real Power
40380 40381 1 M_AC_Power int16 Watts Total Real Power (sum of active phases)
40381 40382 1 M_AC_Power_A int16 Watts Phase A AC Real Power
40382 40383 1 M_AC_Power_B int16 Watts Phase B AC Real Power
40383 40384 1 M_AC_Power_C int16 Watts Phase C AC Real Power
40384 40385 1 M_AC_Power_SF int16 SF AC Real Power Scale Factor
Apparent Power
40385 40386 1 M_AC_VA int16 Volt- Amps Total AC Apparent Power (sum of active phases)
40386 40387 1 M_AC_VA_A int16 Volt- Amps Phase A AC Apparent Power
40387 40388 1 M_AC_VA_B int16 Volt- Amps Phase B AC Apparent Power
40388 40389 1 M_AC_VA_C int16 Volt- Amps Phase C AC Apparent Power
40389 40390 1 M_AC_VA_SF int16 SF AC Apparent Power Scale Factor
Reactive Power
40390 40391 1 M_AC_VAR int16 VAR Total AC Reactive Power(sum of active phases)
40391 40392 1 M_AC_VAR_A int16 VAR Phase A AC Reactive Power
40392 40393 1 M_AC_VAR_B int16 VAR Phase B AC Reactive Power
40393 40394 1 M_AC_VAR_C int16 VAR Phase C AC Reactive Power
40394 40395 1 M_AC_VAR_SF int16 SF AC Reactive Power Scale Factor
Power Factor
40395 40396 1 M_AC_PF int16 % Average Power Factor (average of active phases)
40396 40397 1 M_AC_PF_A int16 % Phase A Power Factor
40397 40398 1 M_AC_PF_B int16 % Phase B Power Factor
40398 40399 1 M_AC_PF_C int16 % Phase C Power Factor
40399 40400 1 M_AC_PF_SF int16 SF AC Power Factor Scale Factor
Accumulated Energy
Real Energy
40400 40401 2 M_Exported uint32 Watt- hours Total Exported Real Energy
40402 40403 2 M_Exported_A uint32 Watt- hours Phase A Exported Real Energy
40404 40405 2 M_Exported_B uint32 Watt- hours Phase B Exported Real Energy
40406 40407 2 M_Exported_C uint32 Watt- hours Phase C Exported Real Energy
40408 40409 2 M_Imported uint32 Watt- hours Total Imported Real Energy
40410 40411 2 M_Imported_A uint32 Watt- hours Phase A Imported Real Energy
40412 40413 2 M_Imported_B uint32 Watt- hours Phase B Imported Real Energy
40414 40415 2 M_Imported_C uint32 Watt- hours Phase C Imported Real Energy
40416 40417 1 M_Energy_W_SF int16 SF Real Energy Scale Factor

Technical Note – SunSpec Logging in SolarEdge Inverters

 27

Apparent Energy
40417 40418 2 M_Exported_VA uint32 VA-hours Total Exported Apparent Energy
40419 40420 2 M_Exported_VA_ A uint32 VA-hours Phase A Exported Apparent Energy
40421 40422 2 M_Exported_VA_ B uint32 VA-hours Phase B Exported Apparent Energy
40423 40424 2 M_Exported_VA_ C uint32 VA-hours Phase C Exported Apparent Energy
40425 40426 2 M_Imported_VA uint32 VA-hours Total Imported Apparent Energy
40427 40428 2 M_Imported_VA_ A uint32 VA-hours Phase A Imported Apparent Energy
40429 40430 2 M_Imported_VA_ B uint32 VA-hours Phase B Imported Apparent Energy
40431 40432 2 M_Imported_VA_ C uint32 VA-hours Phase C Imported Apparent Energy
40433 40434 1 M_Energy_VA_S F int16 SF Apparent Energy Scale Factor
Reactive Energy
40434 40435 2 M_Import_VARh_ Q1 uint32 VAR-hours Quadrant 1: Total Imported Reactive Energy
40436 40437 2 M_Import_VARh_ Q1A uint32 VAR-hours Phase A - Quadrant 1: Imported Reactive Energy
40438 40439 2 M_Import_VARh_ Q1B uint32 VAR-hours Phase B- Quadrant 1: Imported Reactive Energy
40440 40441 2 M_Import_VARh_ Q1C uint32 VAR-hours Phase C- Quadrant 1: Imported Reactive Energy
40442 40443 2 M_Import_VARh_ Q2 uint32 VAR-hours Quadrant 2: Total Imported Reactive Energy
40444 40445 2 M_Import_VARh_ Q2A uint32 VAR-hours Phase A - Quadrant 2: Imported Reactive Energy
40446 40447 2 M_Import_VARh_ Q2B uint32 VAR-hours Phase B- Quadrant 2: Imported Reactive Energy
40448 40449 2 M_Import_VARh_ Q2C uint32 VAR-hours Phase C- Quadrant 2: Imported Reactive Energy
40450 40451 2 M_Export_VARh_ Q3 uint32 VAR-hours Quadrant 3: Total Exported Reactive Energy
40452 40453 2 M_Export_VARh_ Q3A uint32 VAR-hours Phase A - Quadrant 3: Exported Reactive Energy
40454 40455 2 M_Export_VARh_ Q3B uint32 VAR-hours Phase B- Quadrant 3: Exported Reactive Energy
40456 40457 2 M_Export_VARh_ Q3C uint32 VAR-hours Phase C- Quadrant 3: Exported Reactive Energy
40458 40459 2 M_Export_VARh_ Q4 uint32 VAR-hours Quadrant 4: Total Exported Reactive Energy
40460 40461 2 M_Export_VARh_ Q4A uint32 VAR-hours Phase A - Quadrant 4: Exported Reactive Energy
40462 40463 2 M_Export_VARh_ Q4B uint32 VAR-hours Phase B- Quadrant 4: Exported Reactive Energy
40464 40465 2 M_Export_VARh_ Q4C uint32 VAR-hours Phase C- Quadrant 4: Exported Reactive Energy
40466 40467 1 M_Energy_VAR_ SF int16 SF Reactive Energy Scale Factor
Events
40467 40468 2 M_Events uint32 Flags See M_EVENT_ flags. 0 = nts.

Technical Note – SunSpec Logging in SolarEdge Inverters

28

Meter 3

Address Size Name Type Units Description

(base 0) (base 1)
Common Block
40469 40470 1 C_SunSpec_DID uint16 N/A Value = 0x0001. Uniquely identifies this as a SunSpec
Common Model Block
40470 40471 1 C_SunSpec_Length uint16 N/A 65 = Length of block in 16-bit registers
40472 40473 16 C_Manufacturer String(32) N/A Meter manufacturer
40488 40489 16 C_Model String(32) N/A Meter model
40504 40505 8 C_Option String(16) N/A Export+Import, Production, Consumption,
40512 40513 8 C_Version String(16) N/A Meter version
40520 40521 16 C_SerialNumber String(32) N/A Meter SN
40536 40537 1 C_DeviceAddress uint16 N/A Inverter Modbus ID
Identification
40537 40538 1 C_SunSpec_DID uint16 N/A Well-known value. Uniquely identifies this as a
SunSpec MODBUS Map:
 Single Phase (AN or AB) Meter (201)
 Split Single Phase (ABN) Meter (202)
 Wye-Connect Three Phase (ABCN) Meter (203)
 Delta-Connect Three Phase (ABC) Meter(204)
40538 40539 1 C_SunSpec_Length uint16 Registers Length of meter model block
Current
40539 40540 1 M_AC_Current int16 Amps AC Current (sum of active phases)
40540 40541 1 M_AC_Current_A int16 Amps Phase A AC Current
40541 40542 1 M_AC_Current_B int16 Amps Phase B AC Current
40542 40543 1 M_AC_Current_C int16 Amps Phase C AC Current
40543 40544 1 M_AC_Current_S F int16 SF AC Current Scale Factor
Voltage
Line to Neutral Voltage
40544 40545 1 M_AC_Voltage_L N int16 Volts Line to Neutral AC Voltage (average of active phases)
40545 40546 1 M_AC_Voltage_A N int16 Volts Phase A to Neutral AC Voltage
40546 40547 1 M_AC_Voltage_B N int16 Volts Phase B to Neutral AC Voltage
40547 40548 1 M_AC_Voltage_C N int16 Volts Phase C to Neutral AC Voltage
Line to Line Voltage
40548 40549 1 M_AC_Voltage_L L int16 Volts Line to Line AC Voltage (average of active phases)
40549 40550 1 M_AC_Voltage_A B int16 Volts Phase A to Phase B AC Voltage
40550 40551 1 M_AC_Voltage_B C int16 Volts Phase B to Phase C AC Voltage
40551 40552 1 M_AC_Voltage_C A int16 Volts Phase C to Phase A AC Voltage
40552 40553 1 M_AC_Voltage_S F int16 SF AC Voltage Scale Factor
Frequency
40553 40554 1 M_AC_Freq int16 Herts AC Frequency

Technical Note – SunSpec Logging in SolarEdge Inverters

 29

40554 40555 1 M_AC_Freq_SF int16 SF AC Frequency Scale Factor

Power
Real Power
40555 40556 1 M_AC_Power int16 Watts Total Real Power (sum of active phases)
40556 40557 1 M_AC_Power_A int16 Watts Phase A AC Real Power
40557 40558 1 M_AC_Power_B int16 Watts Phase B AC Real Power
40558 40559 1 M_AC_Power_C int16 Watts Phase C AC Real Power
40559 40560 1 M_AC_Power_SF int16 SF AC Real Power Scale Factor
Apparent Power
40560 40561 1 M_AC_VA int16 Volt- Amps Total AC Apparent Power (sum of active phases)
40561 40562 1 M_AC_VA_A int16 Volt- Amps Phase A AC Apparent Power
40562 40563 1 M_AC_VA_B int16 Volt- Amps Phase B AC Apparent Power
40563 40564 1 M_AC_VA_C int16 Volt- Amps Phase C AC Apparent Power
40564 40565 1 M_AC_VA_SF int16 SF AC Apparent Power Scale Factor
Reactive Power
40565 40566 1 M_AC_VAR int16 VAR Total AC Reactive Power (sum of active phases)
40566 40567 1 M_AC_VAR_A int16 VAR Phase A AC Reactive Power
40567 40568 1 M_AC_VAR_B int16 VAR Phase B AC Reactive Power
40568 40569 1 M_AC_VAR_C int16 VAR Phase C AC Reactive Power
40569 40570 1 M_AC_VAR_SF int16 SF AC Reactive Power Scale Factor
Power Factor
40570 40571 1 M_AC_PF int16 % Average Power Factor (average of active phases)
40571 40572 1 M_AC_PF_A int16 % Phase A Power Factor
40572 40573 1 M_AC_PF_B int16 % Phase B Power Factor
40573 40574 1 M_AC_PF_C int16 % Phase C Power Factor
40574 40575 1 M_AC_PF_SF int16 SF AC Power Factor Scale Factor
Accumulated Energy
Real Energy
40575 40576 2 M_Exported uint32 Watt- hours Total Exported Real Energy
40577 40578 2 M_Exported_A uint32 Watt- hours Phase A Exported Real Energy
40579 40580 2 M_Exported_B uint32 Watt- hours Phase B Exported Real Energy
40581 40582 2 M_Exported_C uint32 Watt- hours Phase C Exported Real Energy
40583 40584 2 M_Imported uint32 Watt- hours Total Imported Real Energy
40585 40586 2 M_Imported_A uint32 Watt- hours Phase A Imported Real Energy
40587 40588 2 M_Imported_B uint32 Watt- hours Phase B Imported Real Energy
40589 40590 2 M_Imported_C uint32 Watt- hours Phase C Imported Real Energy
40591 40592 1 M_Energy_W_SF int16 SF Real Energy Scale Factor
Apparent Energy
40592 40593 2 M_Exported_VA uint32 VA-hours Total Exported Apparent Energy
40594 40595 2 M_Exported_VA_ A uint32 VA-hours Phase A Exported Apparent Energy

Technical Note – SunSpec Logging in SolarEdge Inverters

30

40596 40597 2 M_Exported_VA_ B uint32 VA-hours Phase B Exported Apparent Energy

40598 40599 2 M_Exported_VA_ C uint32 VA-hours Phase C Exported Apparent Energy
40600 40601 2 M_Imported_VA uint32 VA-hours Total Imported Apparent Energy
40602 40603 2 M_Imported_VA_ A uint32 VA-hours Phase A Imported Apparent Energy
40604 40605 2 M_Imported_VA_ B uint32 VA-hours Phase B Imported Apparent Energy
40606 40607 2 M_Imported_VA_ C uint32 VA-hours Phase C Imported Apparent Energy
40608 40609 1 M_Energy_VA_S F int16 SF Apparent Energy Scale Factor
Reactive Energy
40610 40611 2 M_Import_VARh_ Q1 uint32 VAR-hours Quadrant 1: Total Imported Reactive Energy
40612 40613 2 M_Import_VARh_ Q1A uint32 VAR-hours Phase A - Quadrant 1: Imported Reactive Energy
40614 40615 2 M_Import_VARh_ Q1B uint32 VAR-hours Phase B- Quadrant 1: Imported Reactive Energy
40616 40617 2 M_Import_VARh_ Q1C uint32 VAR-hours Phase C- Quadrant 1: Imported Reactive Energy
40618 40619 2 M_Import_VARh_ Q2 uint32 VAR-hours Quadrant 2: Total Imported Reactive Energy
40620 40621 2 M_Import_VARh_ Q2A uint32 VAR-hours Phase A - Quadrant 2: Imported Reactive Energy
40622 40623 2 M_Import_VARh_ Q2B uint32 VAR-hours Phase B- Quadrant 2: Imported Reactive Energy
40624 40625 2 M_Import_VARh_ Q2C uint32 VAR-hours Phase C- Quadrant 2: Imported Reactive Energy
40626 40627 2 M_Export_VARh_ Q3 uint32 VAR-hours Quadrant 3: Total Exported Reactive Energy
40628 40629 2 M_Export_VARh_ Q3A uint32 VAR-hours Phase A - Quadrant 3: Exported Reactive Energy
40630 40631 2 M_Export_VARh_ Q3B uint32 VAR-hours Phase B- Quadrant 3: Exported Reactive Energy
40632 40633 2 M_Export_VARh_ Q3C uint32 VAR-hours Phase C- Quadrant 3: Exported Reactive Energy
40634 40635 2 M_Export_VARh_ Q4 uint32 VAR-hours Quadrant 4: Total Exported Reactive Energy
40636 40637 2 M_Export_VARh_ Q4A uint32 VAR-hours Phase A - Quadrant 4: Exported Reactive Energy
40638 40639 2 M_Export_VARh_ Q4B uint32 VAR-hours Phase B- Quadrant 4: Exported Reactive Energy
40640 40641 2 M_Export_VARh_ Q4C uint32 VAR-hours Phase C- Quadrant 4: Exported Reactive Energy
40642 40643 1 M_Energy_VAR_ SF int16 SF Reactive Energy Scale Factor
Events
40643 40644 2 M_Events uint32 Flags See M_EVENT_ flags. 0 = nts.

Technical Note – SunSpec Logging in SolarEdge Inverters

 31

Appendix A – Supported MODBUS Request Methods

SolarEdge has implemented two methods of the MODBUS request procedure:

MODBUS request with explicit register addressing - supported by all communication board CPU versions. For example:
• Tx: 01 03 9C 40 00 7A EB AD – Read 122 registers starting at address 40001.
• Rx: 01 03 F4 53 75 … [Registers data] … FF FF 12 1B
MODBUS request without explicit addressing – supported by communication board CPU version 2.478 and above. For example:
• Tx: 01 03 00 00 00 7A C4 29 – Read 122 registers starting at offset 0.
• Rx: 01 03 F4 53 75 6E 53 … [Registers data] … FF FF AE DB

Technical Note – SunSpec Logging in SolarEdge Inverters

32

Appendix B – Response Time Information

When directly connected through either the same RS485 bus or Ethernet, the response time of an inverter is <100 ms per inverter
@115200bps.

NOTE
For connectivity purposes, the Synergy Manager is considered a single follower.

Inverters with the following CPU firmware versions support a response time of 1 second, regardless of the number of inverters:

Inverters with LCD or Commercial Gateway – 3.226x-3.2299, 3.245x and above

Inverters with SetApp configuration – 4.4.5x and above

When connected through a Commercial Gateway, the response delay through the Commercial Gateway can be as much as
N*100 [ms]+60 [ms], where:

N is the number of Follower inverters on the bus

100 ms is the maximum slot time per Follower in the SolarEdge bus

60 ms is a constant delay for MODBUS packet assuming 115200 bps

The timeout delay per Follower inverter is the sum of:

N*100 [ms] - SolarEdge bus delay of N Followers, assuming each inverter transmits one SolarEdge telemetry and one full
MODBUS response per grant slot.

256 * 10000/Baud rate [ms] - at least one full MODBUS packet over the MODBUS link, and limited to a minimum of 60 ms
(hardcoded).

For example, the timeout delay of a bus of 10 Followers and a 115200 bps MODBUS link is: 1000 [ms] + 60 [ms].

Part of the slot is also consumed by the Follower inverters transmitting SolarEdge telemetries at the same time.

Consider the following if trying to reduce delays when a Commercial Gateway is installed:

Waiting for a response is part of the MODBUS definition, and this is limiting the bandwidth.

Multiple retries may result in multiple replies, as the inverters receive all the MODBUS commands, but the SolarEdge bus
topology delays the response. In this case, implementing a no-response-expected MODBUS command may balance between
performance and reliability, as:
• Inverters can be controlled with no delay except for the fixed 60 ms per inverter (since a response is not expected).
• An ACK from the inverter is not expected and the measured power from the meter is used as the feedback loop.
• The responses from all the inverters are received in an Nx100 ms timeframe, which can be used for a sanity check.
• If you try 0 [ms] timeout, expect the timeout to occur intentionally and disregard it.
If you use MODBUS-over-SolarEdge with MODBUS replies, consider lower rates.

Technical Note – SunSpec Logging in SolarEdge Inverters

 33

Appendix C – Encoding and Decoding 32-bit Values in Modbus

In Modbus, 32-bit values span two registers. This appendix explains how to encode and decode these registers correctly.

Since 32-bit values span two registers, they must be written in a single transaction of Write Multiple Registers (Function code 10) and
not two consecutive Write Single Register (Function code 06) transactions.

32-bit Unsigned Integer (uint32)

Read Request

Unit ID Function Address Register Amount

Request 01 03 (Read Holding Registers) F604 00 02
Unit ID Function Address Reg[0] Reg[1]
Response 01 03 (Read Holding Registers) F604 00 A0 00 00
Decoding Data First register (0xF604) stores the least significant bytes: 0x00A0.
Second register (0xF605) stores the most significant bytes: 0x0000.
Decoded value: 0x0000 0x00A0 = 160

Write Request

Unit ID Function Address Register Byte Reg[0] Reg[1]

Amount Count
Request 01 10 (Write Multiple Registers) F6 04 00 02 04 09 61 00 55
Unit ID Function Address Register Amount
Response 01 10 (Write Multiple Registers) F6 04 00 02
Encoding Data New value: 5572961 (0x00550961)
First register (0xF604) will store the least significant bytes: 0x0961.
Second register (0xF605) will store the most significant bytes: 0x0055.

Technical Note – SunSpec Logging in SolarEdge Inverters

34

32-bit Single Precision Floating Point (float32)

Read Request

Unit ID Function Address Register Amount

Request 01 03 (Read Holding Registers) F606 00 02
Unit ID Function Address Reg[0] Reg[1]
Response 01 03 (Read Holding Registers) F606 CC CD 43 8E
Decoding Data First register (0xF606) stores the least significant bytes: 0xCCCD.
Second register (0xF607) stores the most significant bytes: 0x438E.
Decoded value: 0xCCCD 0x438E = 285.6

Write Request

Unit ID Function Address Register Byte Reg[0] Reg[1]

Amount Count
Request 01 10 (Write Multiple Registers) F6 06 00 02 04 19 9A 43 91
Unit ID Function Address Register Amount
Response 01 10 (Write Multiple Registers) F6 06 00 02
Encoding Data New value: 290.2 (0x4391199A)
First register (0xF606) will store the least significant bytes: 0x199A.
Second register (0xF607) will store the most significant bytes: 0x4391.

Technical Note – SunSpec Logging in SolarEdge Inverters

 35

Support Contact Information

If you have technical problems concerning SolarEdge products, please contact us:

https://www.solaredge.com/service/support

Before contact, make sure to have the following information at hand:

Model and serial number of the product in question.

The error indicated on the product SetApp mobile application LCD screen or on the monitoring platform or by the LEDs, if
there is such an indication.

System configuration information, including the type and number of modules connected and the number and length of strings.

The communication method to the SolarEdge server, if the site is connected.

The product's software version as it appears in the ID status screen.

Technical Note – SunSpec Logging in SolarEdge Inverters