Why NFPA 2112 should be important

in my FR Clothing Program

Derek Sang
Technical Training Manager
Bulwark Protective Apparel
Background

• Involved with the Flame Resistant Clothing market from

the service, manufacturing and garment sides for over
20 years.
• Over the past 11 years worked closely with fortune 1000
companies as they look develop PPE programs within
their Electrical Safe Work Practices to comply with
NFPA70E/NESC and also Flash Fire programs for NFPA
2113.
• Developed and conducted over 250 educational and
informational seminars on the Hazards of Arc Flash and
Flash Fire for NSC, ASSE, VPPPA, NJATC, NECA,
CAER and numerous other associations.
Objectives

• Understand what the test method ASTM 1930

measures vs real world
• Understand the relationship between NFPA 2112 and
2113
• Understand the value of UL certification
• Understand the concerns regarding rainwear
• Understand some of the do’s and Don’ts
OSHA General Duty Clause – OSH Act 1970

• Employer’s responsibility / Choosing FR/AR

SEC. 5. Duties

(a) Each employer --

(1) shall furnish to each of his employees

employment and a place of employment
which are free from recognized hazards that
are causing or are likely to cause death or
serious physical harm to his employees;
1910.132(d)(1)

• The employer shall assess the workplace to determine if hazards are

present, or are likely to be present, which necessitate the use of personal
protective equipment (PPE). If such hazards are present, likely to be
present, the employer shall:
1910.132(d)(1)(i)
Select, and have each affected employee
use, the types of PPE that will protect the
affected employee from the hazards
identified in the hazard assessment;
1910.132(d)(1)(ii)
Communicate selection decisions to each
affected employee; and,
1910.132(d)(1)(iii)
Select PPE that properly fits each affected
employee
The difference between NFPA® 2112 and 2113

• NFPA 2112 is the Standard on Flame-Resistant Garments for Protection of

Industrial Personnel Against Flash Fire. This standard outlines the various
performance requirements and testing methods for both the FR fabric and FR
garments that are needed to be considered in compliance with the standard. It
also includes proper labeling and quality control requirements for the FR
manufacturers. This is the standard most recognized in the flash fire industry and
compliance with it is typically asked for by end users. Although meeting the
performance requirements of NFPA 2112 is important, NFPA 2113 is needed to
determine what kind of FR you should consider.

• NFPA 2113 is “Standard on Selection, Care, Use and Maintenance of Flame

Resistant Garments for Protection of Industrial Personnel against Flash Fire.” NFPA
2113 provides greater detail on how to select proper FR garments. Chapter 4
speaks directly to Selection and gives guidance on Hazard Assessment, Selection of
FR Garments and Purchase Specifications.
Industries Requiring FR Clothing

Oil exploration
Oil drilling
Oil field services
Oil refining
Refinery services
Chemical plants
The Benefit of FR Clothing
Injuries and Fatalities do Happen

• According to the Bureau of Labor Statistics,

109 workers died from fires in 2010 alone.

• OSHA reports more than 5,000 are injured in

explosions and fires on the job each year
2014, there were at least eight fatal oil and gas
explosions in the United States
Real World Flash Fire vs ASTM 1930

• It is important to understand the difference between

the ASTM 1930 test method for fabric and real world
Flash Fires
• Many decision makers have been influenced to focus
on the results of ASTM 1930 testing alone without
fully understanding how to view the information
• Some manufacturers have attempted to “make up” a
category “flash fire rated” that only focuses on ASTM
1930 test results
Instrumented Manikin Test
Instrumented Manikin Results

NCSU
Instrumented Manikin Results

NCSU
Instrumented Manikin Results
 NFPA 2112 requires
less than 50% predicted
body burn
ASTM 1930 – Explanation

One requirement that warrants additional explanation is the manikin

test requirement. This test involves placement of a flame-resistant
garment on a manikin with exposure to a 3-second duration, 84
kW/m2 (2.0 cal/cm2 · sec) intensity engulfment “jet” fire. The test is
used as a qualification of garment fabric performance, not the garment
design, since a standard garment design is used for evaluating the
fabric. The standard garment is a coverall with a front slide fastener
(zipper) closure and no pockets. Flame-resistant garments with
different designs are not evaluated using this test. Organizations
should judge the performance of their garment designs by comparing
their design with that of the standard garment design or conduct
independent testing. Garment designs that provide different areas of
body coverage, have different closure systems, or have pockets can
demonstrate lesser or better performance than the standard garment
design
Flash Fires are Log-Normal Distribution

H
E
A
T

F
L
U
X
Approximate Time in seconds
 Time Line

Rapidly moving flame front

Moves towards ignition source Dispersed - dust, gas and/or vapor

Key differences between Flash Fires
and ASTM 1930 testing in the lab

Flash Fire ASTM 1930

• It is a” flash” fire • “jet” fire

• Duration varies • 3 seconds
• Rapid moving flame front • 360 degrees exposure
• Removed quickly once • 60 seconds data
safe collection
• Garment – pockets etc. • Fabric – single layer
What does this mean?

Take our examples from ASTM 1930 testing – 32% BB and 14% BB

• If the actual exposure is not 3 seconds but may be less 1.5 sec
– Cut the numbers in half
• If it is not 360 degree exposure but 180 degree
– Cut the new numbers in half
• If we are not going to stay in that hot garment for 60 seconds
but get out of it in 30 seconds
– Cut the new numbers in half – what do you get
 NFPA 2112 Standard
– Defines a “Flash Fire”
• 2112 – Flash Fire - A Fire that spreads by means of a flame front rapidly through a
diffuse fuel such as a dust, gas or vapors of an ignitable liquid, without the
production of damaging pressure

– Defines minimum performance requirements to be

independently Certified to be NFPA2112 Compliant
– Are promulgated by a committee of industry members
– Include a battery of test methods all of which must be
passed
– Are continuously under review & revision
NFPA 2112

Standard on Flame Resistant Garments for Protection of

Industrial Personnel Against Flash Fire

• What it is….

– A means of certifying fabrics & findings suitable for use in

FR clothing to be worn as protection against possible flash
fire exposure
NFPA 2112 – How to make garments for
Flash Fire Exposure

• Vertical Flame Test 12 sec exposure, 2.0 sec max after flame,
4” max char length

• Oven Test10% max shrinkage after 5 minutes in 500 F, no

melting/dripping allowed

• Heat Transfer Performance (HTP):6 cal/cm2 with spacer; 3

cal/cm2 without spacer

• ASTM F1930 Instrumented Manikin:50% max body burn

following 3 sec 2.0 cal/cm2 exposure
NFPA 2112 Compliant

• Garments and components must be certified by a third party

(i.e. Underwriters Laboratories)
• Annual inspection and testing of materials and components
• Annual audit of quality system
• The 3 F’s Fabrics, Findings and Facilities – with out the 3 F’s
you have 1 F = Failure
 What’s UL?
3rd party certifier that audits manufacturing facilities and conducts independent
testing on products to assure compliance with appropriate industry standards.
So what does 3rd party certified mean to me?

• Based on what we know today – it gives you piece of mind

that this garments meets or exceeds all the standards and
tests available for the hazard
• You don’t need to choose NFPA 2112 certified garments but if
you don’t why didn’t you?
• If you are not going to use NFPA 2112 What are you going to
use?
 Are all flame resistant fabrics and garments
Independently Certified to be NFPA 2112 compliant?

NO!
So Where can you look
NFPA 2112 Label Requirements

We are all too familiar with misleading claims but are you aware of misleading labels in FR
garments? NFPA mandates strict labeling requirements and not everyone follows the
rules. In addition to bearing the mark of the 3rd party certifier, these words and the
edition of the standard must appear on the label of a certified garment:
"THIS FLAME-RESISTANT GARMENT MEETS THE REQUIREMENTS OF NFPA 2112-2012
STANDARD ON THE FLAME-RESISTANT GARMENTS FOR THE PROTECTION OF INDUSTRIAL
PERSONNEL AGAINST FLASH FIRE”
Beware of subtle changes in wording on the label that claim to meet a portion of the
standard. The following language does not meet the requirements of NFPA 2112:
"THIS GARMENT MEETS THE PERFORMANCE REQUIREMENTS OF NFPA 70E-2009, ASTM
F1506-02ae1, NFPA 2112-2007.
NFPA 2112 – 4.1 General.

4.1.1 All flame-resistant garments that are

labeled as being compliant with this standard
shall meet or exceed all applicable
requirements specified in this standard and
shall be certified.
4.2.5.2 Manufacturers shall not be authorized
to use any label or reference to the
certification organization on products that are
not manufactured in compliance with all
applicable requirements of this standard.
4.1.6 Manufacturers shall not claim
compliance with a portion(s) or segment(s) of
the requirements of this standard and shall not
use the name or identification of this standard
in any statements about their respective
product(s) unless the product(s) is certified as
compliant to this standard
 Read garments labels carefully…..
Required labeling Misleading Label
THIS FLAME-RESISTANT GARMENT THIS GARMENT MEETS THE
MEETS THE REQUIREMENTS OF NFPA 2112
STANDARD ON FLAME-RESISTANT GARMENTS PERFORMANCE REQUIREMENTS OF
FOR PROTECTION OF INDUSTRIAL PERSONNEL NFPA 70E-2012, ASTM F1506-
AGAINST FLASH FIRE, 2012 EDITION. 02ae1, NFPA 2112-2012.
Some Standards alone are not enough;
some are just wrong

• ASTM F2302 – 1.3 This specification does not pertain to applications where the
conditions of potential flame contact or heat exposure are of an extended duration and/or
are of a high intensity. Note 1—Examples include fire fighting applications, exposure to high
energy electrical arcs and exposures in flash fires
• ASTM D6413 – 1.2 This standard shall be used to measure and describe the response of
materials, products, or assemblies to heat and flame under controlled laboratory conditions
and shall not be used to describe or appraise the fire hazard or fire risk of materials,
products, or assemblies under actual fire conditions
• NFPA 701 – Two distinct test methods differentiate fabrics of different densities. The test
methods apply to textile materials used in interior furnishing for public occupancy buildings
including curtains, window shades, draperies, table linens, textile wall hangings, as well as to
fabrics used in the assembly of awnings, tents, tarps and other similar architectural fabric
structures and banners. - See more at: http://www.nfpa.org/codes-and-standards/document-
information-pages?mode=code&code=701#sthash.FcM0WGmG.dpuf
 Be very cautious in Rainwear and Vests

Rainwear has specific standards for

both Arc Flash and Flash Fire
FR Rainwear claims can and are very
misleading
Do not jeopardize your safety and your
FR/AR program by implementing non-
compliant Rainwear and/or vests
Rainwear and vests that are marketed
as FR should not be used in a Flash Fire
– do your homework
Make sure to match the Rainwear to
the hazard – for Arc Flash ASTM 1891
and they will have an ATPV and for
Flash Fire ASTM 2733 better yet get
raingear that is tested to both
The Benefit of Proper FR Rainwear
Proper Use of FR Garments

• FRC should be appropriate

to the hazard
• Always the outermost layer
• Worn correctly; zipped,
buttoned, etc
• All natural, non-melting
undergarments
• Clean, no flammable
contaminants
• Repaired correctly and removed
from service when needed
 NFPA 2113 in addition -
Standard on Selection, Care, Use and Maintenance of Flame Resistant
Garments for Protection of Industrial Personnel Against Flash Fire
Provides common sense protocol for issues like:
– Conducting a hazard assessment
– Selecting FR garments (specifications)
• Upper & lower body coverage
• Non-FR heraldry
– Properly using FR garments (Training)
• Collars, sleeves, cuffs
• Layering
– Care and Maintenance
• Emblems and embroidery
• Cleaning
NFPA 2113

1.1 Scope.
• 1.1.1* This standard shall specify the minimum
selection, care, use, and maintenance requirements
for flame-resistant garments for use by industrial
personnel in areas at risk from flash fires or short-
duration flame exposure that are compliant with
NFPA 2112, Standard on Flame-Resistant Garments
for Protection of Industrial Personnel Against Flash
Fire.
NFPA 2113 5.1.1*
Organizations shall provide users with the instructions provided by the manufacturer on the care, use,
and maintenance of flame-resistant garments, including any warning provided by the manufacturer.
5.1.2 Organizations shall instruct workers in the limitations, use, care, and maintenance of flame-
resistant garments, including the use of undergarments or over garments.
5.1.3 For maximum protection, organizations shall require that flame-resistant garments be worn as
described in the manufacturer’s instructions.
5.1.4 Flame-resistant garment collars shall be worn closed.
5.1.5 Sleeves and cuffs shall be worn down and secured.
5.1.6 Organizations shall require that protective neck, head, hand, and foot coverings be worn if the
occupational hazard warrants their use.
5.1.7* Other personal protective equipment (PPE) shall be worn if determined as necessary from a
review of the potential hazards to which workers are exposed from the hazard assessment.
5.1.8* Organizations shall not permit workers to wear non–flame-resistant clothing over flame-
resistant garments.
5.1.9 Flame-resistant or non-melting undergarments (closest to the skin) shall be used. An incidental
amount of elastic used on non-melting fabric underwear or socks shall be permitted.
5.2* Specific Requirements for Wearing Flame-Resistant Garments.
The organization shall define those facilities and areas of the workplace and tasks that require
personnel to wear flame-resistant garments.
Do’s
Don’ts
What could be wrong here???
Always – rolled, tucked and buttoned!
Care

Essential to your PPE’s performance and life expectancy

is caring for your garments
Objectives
• Be able to identify additives that cannot be used on
your FR/AR garments
• To be able to understand and recognize the effect of
stains and secondary accelerants on your FR/AR
garments
1910.132(f)(1)
The employer shall provide training to each employee who is required by this
section to use PPE. Each such employee shall be trained to know at least the
following:
1910.132(f)(1)(i) - When PPE is necessary;
1910.132(f)(1)(ii) - What PPE is necessary;
1910.132(f)(1)(iii) - How to properly don, doff, adjust, and wear PPE;
1910.132(f)(1)(iv) - The limitations of the PPE; and,
1910.132(f)(1)(v) - The proper care, maintenance, useful life and disposal of the
PPE.
1910.132(f)(2) - Each affected employee shall demonstrate an understanding of
the training specified in paragraph (f)(1) of this section, and the ability to use PPE
properly, before being allowed to perform work requiring the use of PPE.
NFPA 2113

6.1.1* Flame-resistant garments shall be kept clean.

6.1.2* New flame-resistant garments shall be washed or dry-cleaned at least
once prior to their initial use.
6.1.3* Flame-resistant garments shall be cleaned in accordance with
manufacturer instructions, or if cleaning instructions are not provided, in
accordance with the recommendations provided in ASTM F 2757-09,
Standard Guide for Home Laundering Care and Maintenance of Flame,
Thermal and Arc Resistant Clothing, or ASTM F 1449, Standard Guide for
Industrial Laundering of Flame, Thermal, and Arc Resistant Clothing.
6.1.4 Flame-resistant garments shall be laundered or dry-cleaned with such
frequency so as to prevent buildup of contaminants that reduce flame
resistance.
• Important to read the
manufacturers laundry
instructions on the label
• Written care instructions are
available for all employees.
• They can also be accessed at:
http://www.bulwark.com/Safety-Care
The Top 3 –

1. Do not use chlorine bleach, peroxide or fabric softener

2. Do not wear if soiled with flammable contaminants
3. Retire garment if worn out
Soiled Garments

• Monitor the accumulation of secondary accelerants on

your garments through out the day.
• After laundering make sure accelerants are removed.
If your garments still have a hydrocarbon/petroleum
odor a flammable contaminant may still be present,
rewash the garment until the odor is gone. If
flammable soils are not completely removed, the
protective qualities of the garment may be
compromised.
• Discoloration/stains alone are not an indicator of
reduced protection
How Much is too much????
Laundering Guidelines -

• Wash FR/AR garments separately

• Turn FR/AR garments inside out both assist in color retention
and appearance
• Use liquid detergent for best results
• Avoid the hottest temperature to reduce the impact of
shrinkage
• For tough stains applying liquid detergent to the stain or stain
remover and allow garment to soak
• Bulwark FR/AR garments can be dry cleaned for tougher stains
• Tumble dry on low setting and do not over dry
What can you Use??
The No’s
Important to Read the Label
Maintenance

Objectives

• Identify when garments need to be repaired and or replaced

• Understand proper repair process for your FR/AR Garments
Inspect garments daily –
• Check for holes, rips and tears
• Check for areas of heavy wear such as elbows and
knees where the fabric may be worn thin
• Check the integrity of the seams
In general check the integrity of the garment and repair
or replace accordingly
 NFPA 2113 Inspection

7.1.1* The organization shall develop a systematic inspection program for all flame-resistant garments
to confirm their serviceability.
7.1.2 The end user shall inspect flame-resistant garments for damage, soiling, or contamination after
each use.
7.1.3 Inspections of flame-resistant garments shall be performed by the organization or the end user
following each cleaning and following any use where there was potential for damage or contamination.
7.1.4 All flame-resistant garments shall be inspected by the organization or the end user for fabric or
material damage.
7.1.4.1 The inspection shall include an examination of all components, including, if present, the outer
shell, lining, interlining, wind/moisture barrier, hardware, wristlets, and reinforcements.
7.1.4.2 Damaged flame-resistant garments shall be immediately removed from service.
7.1.4.3 The decision to repair or retire the damaged flame-resistant garments shall be made by the
organization.
7.1.5 All seams of the flame-resistant garment shall be inspected by the organization or end user for
thread or seam damage as evidenced by skipped, broken, or missing stitches.
7.1.6 All hardware on the flame-resistant garment, including, but not limited to, zippers, buttons,
snaps, and other fasteners, shall be inspected by the organization or end user for functionality.
7.1.7* The organization shall establish criteria for determining the extent of damage to a flame-
resistant garment to warrant its removal from service for repair or disposal.
Inspecting Garments - General

• Evaluate fit
• Worn correctly: shirts are tucked in, sleeves are rolled down, cuffs are
buttoned and shirts are buttoned up (second button from the top)
• Outermost layer is FR/AR
• Wear and tear - thin spots, holes, abrasions, rips, and/or tears, check for
open seams
• No Alterations or modifications
• Not soiled with oils, greases and/or other flammable contaminants
• The easiest time to inspect FR/AR Clothing is just before you put it on in
the morning
• However make sure that you are vigilant throughout the day to avoid
common errors in proper wear
• Repair garments with like materials and FR threads
• If that is not possible retire the garment and replace
What to ask for:

• To see the UL Certification or other independent

organization on that particular garment
• Specify only certified compliant garments are
allowed on site
• Ask for the test data most fabric suppliers have data
sheets with the most common test results
• Work with a proven supply chain
• Periodically police your program for compliance
Questions, Comments, Feedback?
 Bulwark University
Thank You From Your Bulwark Team

Property of Bulwark, not for reproduction without written permission