Riara BQ Rev3 - Blank

Rate
Item Description Qty Unit (Kshs) Amount (Kshs)
ELEMENT NO.1
DEMOLITIONS
(ALL PROVISIONAL)
(All Provisional)
The Contractor is to allow for all temporary protection

required during the alteration works including ordinary
and special dust screens, shoring and strutting,
hoardings, scaffolding, barriers, warning signs, etc as
directed by the Project Manager/Architect
All the Rates for items of demolitions and removal shall include
shoring making good disturbed areas to match existing and
loading and carting away debris unless otherwise specified
The works shall be executed in such order or sequence

as the Project Manager may direct
A All existing works shall be propped, strutted and prepared as

necessary for the alteration work. All debris and surplus
materials arising from demolitions shall be removed from the
site and all existing works disturbed made good to match new
or existing works all to the entire satisfaction of the Project
Architect. The Project Architect shall also identify the
Materials for re-use, and these shall be carefully removed,
cleaned, stored where directed on site and afterwards fixed to
the entire satisfaction of the Project Architect. Materials
arising from demolition reserved for the Employer shall be
carefully cleaned stacked on site where directed and the
Project Architect shall at his sole discretion take possession
of same on or before the date of practical completion,
otherwise clearing away will imply that they become the
property of the Contractor who will allow credit in his rates
accordingly
Item
B Special care should be observed when working within or

adjacent to the existing areas. Dust proof hoarding screens
should be erected to contain any dust, particles or such
matter from falling on to the existing materials and client
property. Where necessary the tenderer is advised to work
in bays (or part of bays) to avoid any disruptions to the
neighbours and ongoing processes.
Item
Bill No. II - Main House Renovations R/1

Rate
Carried to forward to collection Kshs.
Demolish and/or take away and clear the following from

site : except where otherwise stated/directed
Concrete works
A Cut 1400mm wide by 600mm deep through existing

reinforced concrete floor slab and hardcore, to form
thicknessed support footing for staircase (measured
seperately) (Total length - 1.35 Linear metres) Item
B
Carefully hack and demolish existing reinforced concrete floor slab
complete with and including 500mm thick hardcore/sufaces to create
600mm x minimum 1000mm deep trench to receive foundation
strips (m.s.) (Approx. length - 15 Linear metres) Item
C Carefully hack 200mm wide in to existing 150mm thick floor

bed to expose reinforcement to build in a new slab (Approx.
length - 24 linear metres) Item
D Carefully hack and demolish existing suspended timber

decking (Total area - 106 square metres) Item
E Carefully hack and demolish existing reinforced concrete

beams and ringbeams (Approx. length - 74 linear metres) Item
F Ditto existing suspended reinforced concrete staircase sloping

beam complete with wooden steps (Approx. length - 6 linear
metres) Item
Walling
G Carefully demolish existing 200mm thick solid concrete block

walling plastered and painted both sides (Approx. area - 150
square metres) Item
H Carefully remove existing timber cladding and timber walling

(Approx. area - 70 square metres) Item
J Carefully demolish existing 1No. Chimney core and flue

cladded in rubble stone as directed Item
K Carefully hack 200mm wide into faces of existing concrete

columns or masonry walls, create pockets and prepare
surface to receive new masonry walling (Approx. length - 15
linear metres) Item

Rate
Doors
A. Carefully remove existing 10No. 900 x 2100mm high flush

doors faced both sides with 3mm thick ordinary veneer
complete with frame including ironmongery and fixed to
plastered and painted masonry walls Item
B. Carefully remove existing 3No. Mild steel and Aluminium

doors complete with frame and including Burglarproofing
grilles Item
Windows
C. Inspect on site and Carefully demolish and remove existing

18No. glazed mild steel casement windows complete with and
including burglar proofing grilles fixed all round to plastered
and painted masonry walling Item
Finishes
D. Carefully remove existing timber parquet and strips on the

floors and prepare surface to receive new finish(m.s.) (Total
area - 53square metres) Item
E. Carefully remove existing ceramic tiles on the floors and

prepare surface to receive new finish(m.s.) (Total area -
32square metres) Item
F. Wirebrush and rub down existing paint to plastered walls and

prepare surfaces to receive new finish(m.s.) (Approx. area -
380square metres) Item
G. Carefully hack existing 12mm thick plaster to walls and

prepare wall to receive another wall finish (total area - 12
square metres) Item
H. Carefully remove existing precast concrete block paving and

set aside as directed and cart away debris (Approx. area - 12
square metres) Item
Roofing
J. Carefully Demolish the existing pitched roofing comprising

corrugated roof cover on timber purlins; timber trusses
consisting of rafters, ties, struts and ceiling joints; ceiling
boards; including all rainwater goods; fascia boards and
eaves roof over hangs - (Approx. plinth floor area - 185 SM)
Item

Rate
Joinery fittings
A. Carefully demolish existing joinery fittings and cart away

debris Item
Electrical and Sanitary fittings
B. Allow for Inspecting with the Project Architect and Carefully

demolish existing Electrical and Sanitary fittings, set aside for
reuse and cart away debris Item
Credit for Salvaged Materials
C. Allow credit for salvaged materials to be reused in the works

Item
COLLECTION
Brought forward from Page R/1
Brought forward from Above

Rate
TOTAL AMOUNT OF ELEMENT NO.1

DEMOLITIONS
Carried to summary of BILL No. II Kshs
ELEMENT NO.2
SUBSTRUCTURES
(ALL PROVISIONAL)
Excavations
A Excavate to remove vegetable soil average 250mm deep

starting from existing ground level 98 sm
B Excavate for foundation trench not exceeding 1.50 metres

deep starting from reduced level 38 cm
C Extra over excavation for excavating in rock 8 cm
Disposal of excavated materials
Return, fill in, ram and compact excavated material around

D
foundations 17 cm
Load surplus excavated material, spread on site and cart

E
away surplus 45 cm
Planking and Strutting
F Allow for upholding sides of excavations Item
Disposal of Water
G Allow for keeping excavation free from all water Item
Hardcore filling
H 300mm thick Hardcore filling well watered and compacted in

layers not exceeding 150mm thick 76 sm
J 50 mm thick approved stone dust blinding on surfaces of

hardcore to receive concrete 76 sm
Damp Proof Membrane
K Single layer of 1000 gauge polythene sheeting laid on blinded

hardcore with 150 mm side and end laps to receive concrete
(measured separately) 77 sm
Soil Sterilization

Rate
L Apply 'Gladiator TC' or similar approved anti-termite chemical
treatment; applied by an approved professional pest control
specialist with 10year guarantee; strictly applied in
accordance with manufacturer's instructions 98 sm
CONCRETE WORK
Concrete class 1:3:6 (40mm aggregate)
A 50 mm Blinding under strip foundations 40 sm
Vibrated reinforced concrete class 25(20mm aggregate)
B Foundation trench 8 cm
C 100mm Thick floor bed 77 sm
D Steps 1 cm
Supply and fix steel bar reinforcement including bending,

hooking, tying wire, cutting spacers and supporting all in
position
High yield square twisted bar reinforcement to B.S. 4661 :-
E Y8 82 Kg
F Y10 149 Kg
Steel fabric mesh reinforcement to B.S. 4483
G BRC mesh fabric reinforcement reference A142 (weighing

2.22 kg/m2) laid in slab (measured net - no allowance made
for laps) 77 sm
Sawn formwork to: -
H Vertical sides of strip footings 26 sm
I Edges of floor bed 75-150mm high 42 m
J Ditto to risers of steps 11 m

Rate
MASONRY
Selected and approved stone load bearing (7.0N/mm2) walling

: bedded jointed and pointed in cement and sand (1:4)
mortar : reinforced with 25 x 3mm hoop iron strip laid
horizontally every alternate course to approval
A 200mm walling in foundations 79 sm
Plinth finishes
B 12 mm Thick cement and sand (1:4) render to edges of

plinths 13 sm
C Prepare and applyone undercoat and two finishing coats of

bituminous paint or other equal an approved water resistant
paint; on rendered plinths (m.s.) 13 sm
Paving
D
"Bamburi Special Products"or other equal and approved 50mm thick
medium duty paving blocks to match existing on and including
sandbed complete with sanding and sloping to approval 22 sm
E
Take from store salvaged 600 x 600mm x 50mm thick precast
concrete paving slabs on and including sandbed complete with
mortared joints and sloping to approval ; and allow for supplying
and fixing new to replace damaged and replenish deficit 14 sm
COLLECTION

Rate
TOTAL AMOUNT OF ELEMENT NO.2

SUBSTRUCTURES
Carried to summary of BILL No. I Kshs
ELEMENT NO. 3
REINFORCED CONCRETE SUPERSTRUCTURE
A Ring Beams 9 cm
B Beams 4 cm
C 150mm Thick horizontal suspended slab 55 sm
D 175mm Thick Ditto 47 sm
Steel bar reinforcement
Supply and fix steel bar reinforcement including bending,

hooking, tying wire, cutting spacers and supporting all in
position
High tensile square twisted to BS 4461 as described in:-
E 8mm Bars 1,059 Kg
F 10 mm Ditto 1,512 Kg
G 12 mm Ditto 454 Kg
Sawn formwork as described to:-
H Horizontal soffits of suspended slab 102 sm
J Sides and horizontal soffits of beams 173 sm
K Edges of suspended slab over 75 and not exceeding 150 mm

high 35 m
L Edges of suspended slab over 150 and not exceeding 225

mm high 23 m

Rate
TOTAL AMOUNT OF ELEMENT NO. 3

REINFORCED CONCRETE SUPERSTRUCTURE
Carried to Summary of BILL No. II Kshs
ELEMENT NO. 4
WALLING
EXTERNAL WALLING
Machine cut stone walling bedded and jointed in 1:4 cement

and sand mortar and reinforced with hoop iron every alternate
course
A 200mm thick Walling 189 sm
INTERNAL WALLS
Machine cut stone walling bedded and jointed in 1:4 cement

and sand mortar and reinforced with hoop iron every alternate
course
B 200mm thick Walling 61 sm
C 150mm thick Walling 63 sm
Chimney
D Allow a provisional sum for chimney construction complete

with fireplace Item
Horizontal Damp Proof course to B.S 743 (measured net - no

allowance for laps)
E 200 mm wide 46 m
F 150 mm wide 17 m

Rate

WALLING
Carried To Summary of BILL No. II Kshs
ELEMENT NO. 5
STAIRCASE & RAILINGS
A Staircase beam and base complete with steps 1 cm
Steel Bar Reinforcement
High tensile square twisted bars as before described in:-
B 10 mm Ditto 45 Kg
C 12 mm Ditto 65 Kg
Sawn formwork to:-
D Sloping soffites of staircase beam 6 sm
E Edges of risers over 75 and not exceeding 150 mm wide 9 m
Finishes
Plaster & Paint
F 12mm thick smooth trowelled plaster to beams & prepare and

apply 3 coats plastic emulsion paint as Crown or other
approved to beam 6 sm
The following in Wrot Mahogany
G Allow a provisional sum for taking from store and fixing

staircase treads and risers with approved adhesive/mortar :
on backing screeds (m.s.): complete with sanding and
polishing; to Architect's approval Item
H Allow a provisional sum for supplying and fixing new Wrot

mahogany timber treads and risers to match existing (to
replenish deficit) Item

Rate
Balustrading
J Allow a provisional sum for taking from store and fixing

staircase balustrades complete with railing and including
finishing to match existing ; including supplying new where
necessary Item

STAIRCASE & RAILINGS
ELEMENT NO. 6
ROOFING AND RAINWATER DISPOSAL
Roofing construction (All provisional)
CARPENTRY/TIMBER FRAMING/FIRST FIXING
All timber to be approved Seasoned celcured pressure

impregnated sawn pine or equal and approved timber
The following in 5No. Roof trusses T1 spanning 4475mm by

968mm high; raised approximately 3000mm above ground
A 100 x 50mm rafter 32 m
B 100 x 50mm tie beams 24 m
C 100 x 50mm struts and ties 22 m

D 100 x 50mm rafter 38 m
E 100 x 50mm tie beams 32 m
F 100 x 50mm struts and ties 122 m

G 100 x 50mm rafter 15 m
H 100 x 50mm tie beams 12 m

Rate
I 100 x 50mm struts and ties 30 m

J 100 x 50mm rafter 41 m
K 100 x 50mm tie beams 35 m
L 100 x 50mm struts and ties 131 m
Sundries
A 100 x 50mm common rafters 579 m
B 200 x 50mm ridge board 8 m
C 100 x 50mm valley rafters 12 m
Wrot softwood
Cypress
D 225 x 25mm Fascia/Barge boards nailed to end of rafters 53 m
Painting Wood
Knot, prime, stop and paint three coats of gloss oil paint as
Crown or other equal and approved to:
E Fascia or verge girth 225 - 300mm 53 m
Wall plate
F 100 x 50mm wall plate bolted to concrete beam with and

including 12mm diameter ragbolts 300mm long with nuts and
washers at 1000mm centres including mortice in concrete and
run with cement mortar. 86 m
Roof covering
Roofing tiles
G
Take from store and fix roofing tiles complete with underlay
and all necessary accessaories, on and including supply and
fixing 25 x 50mm treated battens; including all necessary
fixing accessories and raking cutting on hips and valleys 85 sm

Rate
"Decra" Roofing tiles
H
1320 x 370mm wide approved 'Decra' Roof covering; to
Architect's approval; at 45 degrees pitches on and including
25 x 50mm treated battens; including all necessary fixing
accessories and raking cutting on hips and valleys 140 sm
I A-Ridge capping to match including all necessary fixing and

end accessories 8 m
J Combination valley; Ditto 6 m
K Flashing twice bent and embedded in wall 47 m
Sundry Items
A Matching 70 x 130mm high Box Barge; including all

necessary fixing accessories 53 m
Eaves finishes
B Take from store and fix T&G ceiling to eaves on and including
50 x 50mm approved celcured softwood brandering
27 sm
Rainwater goods
UPVC rainwater goods
C U-shaped PVC "Typhoon" gutter as Doshi Ltd, or other equal

and approved, fixed to fascia board complete with and
including bends, internal/external angles, union clips and
matching fascia brackets 53 m
D Ditto 110mm diameter down pipe outlet 9 No.
E 110mm diameter downpipe fixed to wall with and including

approved holderbutts 36 m
F Extra over ditto for swan neck bend 9 No.
G Ditto horse shoe bend 9 No.
Water tank deckings in roof
H Allow a provisional sum for 2 No. water tank deckings in roof

space Sum

Rate
COLLECTION

ROOFING AND RAINWATER DISPOSAL
ELEMENT NO. 7
WINDOWS
Mild steel casement windows in standard Z-sections cut and

welded with 150mm top permanent vents filled with mosquito
wire gauze complete with approved brass stays and
fasteners, approved burglar proofing, and 1coat red oxide
primer, all to architects details & schedule;
A 1000 x 1300 mm high window 3 No.
B 750 x 1800 mm high ditto 2 No.
C 1800 x 1800 mm high ditto 3 No.
D 1800 x 1800 mm high ditto but Arched 1 No.
E 600 x 900 mm high ditto 3 No.
F 2400 x 1800 mm high ditto 1 No.
G 1500 x 1200 mm high ditto 2 No.
H 750 x 1050 mm high ditto 4 No.
J 750 x 1650 mm high ditto 1 No.
K 1800 x 1650 mm high ditto 1 No.
L 1200 x 1200 mm high ditto 1 No.
M 600 x 900 mm high ditto 1 No.

Rate
N 750 x 750 mm high ditto 1 No.
O 450 x 750 mm high ditto 1 No.
P 1200 x 1200 mm high ditto 1 No.
Glazing
A
4mm thick clear sheet glass and glazing with putty to mild
steel frames in panes not exceeding 0.10 square metres 38 sm
B Ditto but obscured 3 sm
Window Cills
C 150 mm wide x 75 mm precast concrete window cill with three

labours sunk, weathered and throated cill bedded in cement
and sand (1:4) mortar. 31 m
Window Board
D 230 x 20mm thick Wrot mahogany window board with two

labours plugged complete with 12mm diameter quadrant
beading 26 m
Curtain railing
E Wrot and moulded mahogany Curtain rod with decorative

mouldings complete with rollers and paintwork; to architects
details 32 m
Painting
Prepare and apply three coats of gloss oil paint to;-
F General metal surfaces internally (measured flat overall) 36 sm
G Ditto externally 36 sm

Rate
Prepare and apply three coats of clear polyurethane varnish

to;-
H General surfaces of woodwork 6 sm
COLLECTION

WINDOWS
ELEMENT NO. 8
DOORS
Aluminium doors
A Take from store and fix Standard aluminium sliding door

overall size 1850 x 2100mm high complete with frame, sliding
track, grille and making good and fixing new accessories
where necessary 1 No.
B Supply and fix Standard aluminium double door overall size

1500 x 2400mm high complete with frame, grille and all
necessary ironmongery 1 No.
Mild steel casement doors.
Supply and fix mild steel casement doors, comprising of

25mm x 3mm thick SHS mullions and stiles, 3mm thick mild
steel plate infills and 50mm x 3mm angle line framing,
complete with glazing, with and including purpose made
hinges and all necessary ironmongery, all to architects details
& schedule;-
C
Take from store and fix Standard glazed steel casement
double door overall size 2500 x 2400mm high with side light
complete with 6mm glazing ; 50 x 75mm frame anchored to
masonry walls/concrete, hinges, approved steel door lock ;
finished with red oxide primer and fixed to wall opening (Main
entrance) 1 No.

Rate
D Supply and fix new mild steel single leaf, single swing door
overall size 900 x 2400mm high (Kitchen yard) 1 No.
Prepare and apply three coats gloss oil paint to:-
E General surfaces of metal (measured both sides) 16 sm
F Surfaces not exceeding 100 mm girth 13 m
Flush Doors
G 45mm Thick Solid core flush door overall size 825 x 2050mm
high, faced both sides with pressed skin and lipped with
mahogany all round 5 No.
H Ditto size 725 x 2050mm high (store, baths and toilets) 6 No.
Door Frames
Wrot Mahogany
A 150 x 50mm moulded door frames fixed to walls. 29 m
B 150 x 50mm moulded transome 5 m
C 100 x 50mm moulded door frames fixed to walls. 30 m
D 40 x 15mm Architrave. 59 m
E 20mm diameter quadrant. 59 m
PAINTING AND DECORATING
F Prime back of timber surfaces before fixing, surfaces not

exceeding 100mm girth 30 m
G Prime back of timber surfaces before fixing, surfaces 100-

200mm girth 29 m
Prepare and apply three coats of clear polyurethane

varnish to;-
H General surfaces of timber doors 42 sm
J Ditto 200 - 300mm girth 68 m
K Ditto 0 - 100mm girth 117 m

Rate
Supply and fix the following ironmongery complete with

furniture and matching screws as per 'UNION' catalogue
made in England or approved equivalent:
L Three lever mortice lock complete with Brass handles and all
matching screws, accessories and rebate kits where
necessary 5 No.
M Two lever mortice bathroom lockset complete with handles

and all matching screws and accessories 6 No.
N 100 mm pressed brass hinges. 17 Prs
O 40mm diameter rubber door stop 14 No.
P Aluminium hat and coat hook 8 No.
Sundry Item
Q 40 x 3mm thick fish tailed mild steel holdfast 250mm long

primed with red oxide; fixed to back of door frame and built
into walling 66 No.
COLLECTION

Rate

DOORS
Carried to Summary BILL No. II Kshs
ELEMENT NO. 9
FINISHES
FLOOR FINISHES
Cement and sand (1:3) mortar as described in:-
A 32mm thick to receive ceramic tiles (m/s) 110 sm
B 30mm thick to receive wood Parquet (m/s) 114 sm
C 40mm with red oxide smooth trowelled hard 12 sm
Ceramic tiles floor finish
D
Supply and lay 8mm thick coloured non-slip ceramic tiles as
'SAJ Ceramics Ltd' or other equal and approved laid with
appoved mortar : on backing screeds (m.s): jointed and
pointed in coloured approved proprietary grout: to Floors in
approved pattern 110 sm
E 100mm high skirting 58 m
Wood block floor finish

Rate
F Wood block floor finish laid with appoved mortar : on existing
backing screeds and render: fixed with approved proprietary
adhesive ; complete with aluminium dividers : to Floors in
approved pattern 114 sm
G 150mm high skirting with and including approved backing

mortar 101 m
External Wall Finishes
15mm Thick cement and sand (1:4) wood floated render as

described to:-
H Sides of beams, Masonry walls & columns externally 225 sm
Prepare and apply three coats Exterior quality paint as

'Crown' or other equal and approved paint to:-
I Rendered masonry walls, and sides of beams & columns

externally 225 sm
Prepare and apply two coats Exterior quality paint as 'Crown'

or other equal and approved paint to:-
A Existing Wirebrushed masonry walls, and sides of beams &

columns externally 120 sm
Internal Wall Finishes
12mm Gauged lime plaster (1:2:9) : steel trowelled finish : on

concrete or blockwork : to
B Sides of walls, columns and beams 400 sm
12mm Cement and sand (1:4) backing with wood float finish :
on concrete or blockwork :
C To receive wall tiles (m.s.) 94 sm
Supply and lay approved Ceramic wall tiles with appoved

mortar complete with approved plastic corner strips : on
existing backing screeds and render: jointed and pointed in
coloured approved proprietary grout: to ;
D Walls in approved pattern 94 sm

Rate
Prepare and apply three coats interior quality eggshell paint

as 'Crown' or other equal and approved paint to:-
E Plastered surfaces of walls 400 sm
CEILING FINISHES
15mm two coat gauged lime plaster to:-
F Soffits of suspended slab 102 sm
Gypsum ceiling
G
9mm thick gypsum board ceiling on steel stud work as Donn
Ultrasteel or other equal and approved complete with metal
ceiling trims and decorative recesses, fascias, drops and
mouldings as per Architect's details ; supported by and
including 50 x 50mm cypress brandering on 50 x 50mm
hangers 148 sm
H Extra over gypsum board ceiling for trap door size

600x600mm 1 No.
Moulded cornice
J 75 x 50mm thick moulded gypsum cornice 111 m
Chipboard ceiling
A 12.5mm thick approved chipboard ceiling supported by and

including 50 x 50mm cypress brandering on 50 x 50mm
hangers 79 sm
B
Extra over chipboard ceiling for trap door size 600x600mm 1 No.
Wrot cypress
C 75 x 50mm thick moulded cornice 99 m
Painting
Prepare and apply one coat aluminium primer;-
D Back of timber not exceeding 100mm girth before fixing. 111 m
Prepare and apply three coats emulsion paint to:-

Rate
E Plastered Ceiling surfaces. 102 sm
F Gypsum board Ceiling surfaces. 148 sm
G Surfaces of timber n.e 100mm girth. 111 m
COLLECTION

FINISHES
ELEMENT NO. 10
JOINERY FIXTURES
(All Provisional)
NOTE: All blockboard,MDF boards, etc in joinery

works shall be lipped with hardwood beading all
round before fixing.
Provisional sums to be expended as directed by the Project

Architect and to be deducted in whole or in part if not
required.
A Provide a Provisional Sum of KShillings Four hundred

thousand (KShs. 400,000.00/-) for Kitchen fittings,
Wardrobes Item 400,000.00

Rate

JOINERY FITTINGS
Carried to summary of BILL No. II Kshs 400,000.00
ELEMENT NO. 11
PC & PROVISIONAL SUMS
Provisional sums to be expended as directed by the

Project Architect and to be deducted in whole or in part if
not required.
PLUMBING AND DRAINAGE INSTALLATIONS
A Provide a Provisional Sum for Plumbing and Drainage

Installations Item 350,000.00
Builders work in connection with plumbing and drainage

installations
B Include a Sum for all builders work in connection with
plumbing and drainage installations Item
ELECTRICAL SERVICES INSTALLATIONS

Rate
C Provide a Provisional Sum for Electrical Installations Item 250,000.00
Builders work in connection with Electrical installations
D Include a Sum for all builders work in connection with

Electrical installations Item
EXTERNAL / CIVIL WORKS
E Provide a Provisional Sum for External / Civil works Item 200,000.00
CONTINGENCY
F Provide a Provisional Sum for Contingencies Item 200,000.00

PC & PROVISIONAL SUMS
BILL No. II - MAIN HOUSE
SUMMARY
ELEMENT PAGE No.. AMOUNT
1 PRELIMINARIES & MOBILISATION __
2 DEMOLITIONS R/4
3 SUBSTRUCTURES R/7
4 REINFORCED CONCRETE SUPERSTRUCTURES R/8

Rate
5 WALLING R/9
6 STAIRCASE AND RAILING R/10
7 ROOFING AND RAINWATER DISPOSAL R/13
8 WINDOWS R/15
9 DOORS R/18
10 FINISHES R/21
11 JOINERY FITTINGS R/22
12 PC & PROVISIONAL SUMS R/23
TOTAL CONSTRUCTION COST KShs

Riara BQ Rev3 - Blank

Uploaded by

Copyright:

Available Formats

Riara BQ Rev3 - Blank

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Riara BQ Rev3 - Blank

Uploaded by

Copyright:

Available Formats

Rate

Item Description Qty Unit (Kshs) Amount (Kshs)

The Contractor is to allow for all temporary protection

The works shall be executed in such order or sequence

A All existing works shall be propped, strutted and prepared as

B Special care should be observed when working within or

Bill No. II - Main House Renovations R/1

Carried to forward to collection Kshs.

Demolish and/or take away and clear the following from

A Cut 1400mm wide by 600mm deep through existing

C Carefully hack 200mm wide in to existing 150mm thick floor

D Carefully hack and demolish existing suspended timber

E Carefully hack and demolish existing reinforced concrete

F Ditto existing suspended reinforced concrete staircase sloping

G Carefully demolish existing 200mm thick solid concrete block

H Carefully remove existing timber cladding and timber walling

J Carefully demolish existing 1No. Chimney core and flue

K Carefully hack 200mm wide into faces of existing concrete

Bill No. II - Main House Renovations R/2

Carried to forward to collection Kshs.

A. Carefully remove existing 10No. 900 x 2100mm high flush

B. Carefully remove existing 3No. Mild steel and Aluminium

C. Inspect on site and Carefully demolish and remove existing

D. Carefully remove existing timber parquet and strips on the

E. Carefully remove existing ceramic tiles on the floors and

F. Wirebrush and rub down existing paint to plastered walls and

G. Carefully hack existing 12mm thick plaster to walls and

H. Carefully remove existing precast concrete block paving and

J. Carefully Demolish the existing pitched roofing comprising

Bill No. II - Main House Renovations R/3

Carried to forward to collection Kshs.

A. Carefully demolish existing joinery fittings and cart away

Electrical and Sanitary fittings

B. Allow for Inspecting with the Project Architect and Carefully

Credit for Salvaged Materials

C. Allow credit for salvaged materials to be reused in the works

Carried to forward to collection Kshs.

Brought forward from Page R/1

Brought forward from Page R/2

Brought forward from Page R/3

Brought forward from Above

Bill No. II - Main House Renovations R/4

TOTAL AMOUNT OF ELEMENT NO.1

A Excavate to remove vegetable soil average 250mm deep

B Excavate for foundation trench not exceeding 1.50 metres

C Extra over excavation for excavating in rock 8 cm

Disposal of excavated materials

Return, fill in, ram and compact excavated material around

Load surplus excavated material, spread on site and cart

Planking and Strutting

F Allow for upholding sides of excavations Item

G Allow for keeping excavation free from all water Item

H 300mm thick Hardcore filling well watered and compacted in

J 50 mm thick approved stone dust blinding on surfaces of

Damp Proof Membrane

K Single layer of 1000 gauge polythene sheeting laid on blinded

Bill No. II - Main House Renovations R/5

Carried to forward to collection Kshs.

Concrete class 1:3:6 (40mm aggregate)