Scribd Logo
Upload

Welcome to Scribd!

  • 48 views

    Disassembly: Power Steering Vane Pump (2Jz Ge)

    Uploaded by

    Moh DeBr
    The document provides disassembly instructions for a power steering vane pump. It lists 11 steps to fully disassemble the pump, including removing the pulley, oil reservoir, pressure port union, rear housing, cam ring, vane plates, rotor, pins, gasket, and shaft with bearing. Special tools are required to remove some components and care must be taken to avoid damaging seals and dropping small parts when disassembling the pump.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Disassembly: Power Steering Vane Pump (2Jz Ge)

    Uploaded by

    Moh DeBr
    48 views1 page
    The document provides disassembly instructions for a power steering vane pump. It lists 11 steps to fully disassemble the pump, including removing the pulley, oil reservoir, pressure port union, rear housing, cam ring, vane plates, rotor, pins, gasket, and shaft with bearing. Special tools are required to remove some components and care must be taken to avoid damaging seals and dropping small parts when disassembling the pump.

    Original Title

    m_sr_0015

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides disassembly instructions for a power steering vane pump. It lists 11 steps to fully disassemble the pump, including removing the pulley, oil reservoir, pressure port union, rear housing, cam ring, vane plates, rotor, pins, gasket, and shaft with bearing. Special tools are required to remove some components and care must be taken to avoid damaging seals and dropping small parts when disassembling the pump.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    48 views1 page

    Disassembly: Power Steering Vane Pump (2Jz Ge)

    Uploaded by

    Moh DeBr
    The document provides disassembly instructions for a power steering vane pump. It lists 11 steps to fully disassemble the pump, including removing the pulley, oil reservoir, pressure port union, rear housing, cam ring, vane plates, rotor, pins, gasket, and shaft with bearing. Special tools are required to remove some components and care must be taken to avoid damaging seals and dropping small parts when disassembling the pump.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    SR−15

    STEERING − POWER STEERING VANE PUMP (2JZ−GE)


    SR1HB−01

    DISASSEMBLY
    NOTICE:
    When using a vise, do not overtighten it.
    1. MEASURE PS VANE PUMP ROTATING TORQUE
    (a) Check that the pump rotates smoothly without abnormal
    noise.
    (b) Using a torque wrench, check the pump rotating torque.
    Rotating torque:
    F10342
    0.25 N·m (2.5 kgf·cm, 2.2 in.·lbf) or less

    2. REMOVE VANE PUMP PULLEY


    Using SST, stop the pulley rotating and remove the pulley set
    SST
    nut.
    SST 09960−10010 (09962−01000, 09963−01000)
    3. REMOVE OIL RESERVOIR
    (a) Remove the 3 bolts and oil reservoir.
    (b) Remove the O−ring from the oil reservoir.
    4. REMOVE PRESSURE PORT UNION, FLOW CONTROL
    F10343 VALVE AND SPRING
    (a) Remove the pressure port union, flow control valve and
    spring.
    (b) Remove the O−ring from the pressure port union.
    5. REMOVE REAR HOUSING
    (a) Remove the 2 bolts and rear housing.
    (b) Remove the 2 O−rings from the rear housing.
    6. REMOVE WAVE WASHER
    7. REMOVE SIDE PLATE
    8. REMOVE CAM RING, 10 VANE PLATES AND VANE
    PUMP ROTOR
    NOTICE:
    Be careful not to drop the vane plate.
    9. REMOVE 2 STRAIGHT PINS
    Remove the 2 straight pins from the front housing.
    10. REMOVE GASKET

    Vane Pump Press 11. REMOVE VANE PUMP SHAFT WITH BEARING
    Shaft Vinyl Tape (a) Using snap ring pliers, remove the snap ring from the front
    Front Housing housing.
    (b) To prevent oil seal lip damage, wind vinyl tape on the ser-
    rated part of the vane pump shaft.
    Oil Seal
    Bearing (c) Using a press,press out the vane pump shaft with the
    bearing.
    NOTICE:
    W01277 Be careful not to damage the oil seal lip.

    LEXUS IS300/IS200 SUP (RM870E)

    You might also like