Crystal Radio Operation

Download as pdf or txt
Download as pdf or txt
You are on page 1of 12

Understanding and Operating your Crystal Radio – Jeffrey La Favre – March 28, 2020 – Page 1

Your crystal radio receiver is designed to tune stations on the AM broadcast band (radio frequencies of
540 to 1610 kHz). You will be limited in the number of stations you can hear when operating the radio
without amplification. Keep in mind that a crystal radio operates ONLY on the power received from the
radio station transmitter. Therefore, your ability to hear a station will depend to a great extent on the
distance from the radio transmitter to your house and the amount of power the station uses to
broadcast their signal. Another important factor will be the antenna you use with your radio.

Most of our club members live in Geauga County. As far as I know,


there is no radio station broadcasting on the AM band in our county
(at least not a powerful station). From my home in Chesterland, the
strongest station tuned on my crystal radio is WTAM. This station
broadcasts with 50,000 watts of power on a frequency of 1100 kHz.
The radio transmitter is located at 8200 Snowville Road, Brecksville,
Ohio. The distance from the transmitter to Chesterland is about 23
miles (21 miles to Auburn Twp and 31 miles to Chardon). Figure 1 is
an aerial view of the WTAM transmitting antenna, which is 480 feet
tall.

As radio waves travel away from the transmitter, the power density
of the radio energy varies inversely with the square of the distance.
What does that mean? We can write this as a proportion:

1
power density ∝
distance 2
Let me give some examples. The power density of a radio wave at a
distance of 10 miles from the transmitter is:
Figure 1 WTAM transmitting antenna
1 1
power density ∝ = =0.01
10× 10 100
The power density at 20 miles is:

1 1
power density ∝ = =0.0025
20× 20 400
Therefore, the power density at 20 miles is 1/4 th the power density at a distance of 10 miles. At a
distance of 40 miles, the power density will be 1/16 th the power density at 10 miles. All other things
being equal, if your crystal radio is located 40 miles from the transmitter, the signal strength delivered to
the radio will be 1/16th what it would be if located 10 miles from the transmitter. This is why you will
have a better chance of hearing a station, the closer you are to its transmitter. Of course the amount of
power used in transmitting makes a difference. If two stations are the same distance away, but one
transmits with 1,000 watts of power and another transmits with 50,000 watts, the 50,000 watt station
will be considerably louder than the one with 1,000 watts.

1
Understanding and Operating your Crystal Radio – Jeffrey La Favre – March 28, 2020 – Page 2

Antenna for the Crystal Radio


The antenna you connect to your crystal radio will determine to a great extent the number of stations
you can hear. It is doubtful that an indoor antenna will be sufficient unless you live within a few miles of
an AM radio transmitter. Provided that you have permission from your parents, you can install an
outdoor antenna. You should ask your parents for assistance in erecting the antenna. This can be a
temporary antenna, put up only when you are using the radio, or a more permanent installation. Again,
you should ask your parents which kind of installation they will allow. Some people think that antennas
are not attractive and you must keep this in mind.

The antenna that I use for my crystal radio is of the long wire type (14 gauge, stranded and insulated). It
is permanently installed. I drilled a hole through the window frame to allow the antenna wire to exit
from the GEAR workshop to the outside. I installed a hook on the edge of the roof and with an insulator,
attached the wire antenna. The wire length from window to the edge of the roof is 11 feet. Then the
wire runs to a tree 50 feet from the roof. The attachment to the tree is 18 feet above the ground. The
wire then runs to another tree 61 feet from the first tree and also 18 feet above the ground. At the
second tree the wire goes through a pulley and then down to the ground where it is attached to a
weight. The total length of the antenna wire, from the window to the end is 140 feet (you will also need
additional length inside the house to reach the radio). The pulley is used as part of the antenna
tensioning system. When the wind moves the tree branches, the wire moves through the pulley to
prevent breakage of the wire. The weight at the end of the wire provides the tensioning of the antenna
so that it does not dip excessively toward the ground between its supports. This antenna works well and
I can hear four or five stations during the day.

When you work 18 feet above the ground, there is danger of a serious or fatal injury from a fall. If you
want to erect an antenna like the one I have described, DO NOT ATTEMPT THIS ON YOUR OWN.
PLEASE HAVE YOUR PARENTS HELP YOU. I used a ladder to attach the antenna wire to the trees. This
kind of work can be very dangerous and you must use proper safety procedures. The job takes a
minimum of two people, one to hold the ladder while the other person climbs the ladder. The ladder
should be secured with ropes so that it will not slip off the tree. It is also a good idea to use a safety
harness that connects the climber to the ladder in case they slip on a ladder rung.

A safer procedure, although possibly more frustrating, is to throw a light line over a tree branch from
the ground. Attach a weight to the end of a string and attempt to throw the weight over a branch. If
that does not work you might try using a slingshot. It would be a good idea to wear a hard hat or bicycle
helmet while doing this in case the thrown weight comes back down on your head! If you have a very
long pole, you might use that as well to hoist the wire over a branch. These methods are preferred over
the ladder since they are safer. After you are successful in getting a string line over a tree branch,
connect the string to your antenna wire and pull the string to hoist the antenna wire in place.

Ground Connection for the Crystal Radio


In addition to the antenna, a connection to ground is required. The ground connection is actually part of
the antenna system. For the antenna I have described, I used a grounding rod, which you can find in the
electrical department at a hardware store. The rod is 8 feet long and all but a few inches are driven into
the ground with a sledge hammer. Make sure there are no pipes or underground electrical wires in the
area where you install the grounding rod. It is best to install the rod near where the antenna wire exits

2
Understanding and Operating your Crystal Radio – Jeffrey La Favre – March 28, 2020 – Page 3

the house. The rod is copper-clad steel. A special bronze clamp is used to attach a ground wire to the
rod. The other end of this ground wire is connected to the ground connection (black wire) of the
antenna coil of the radio. The grounding rod must be in moist soil to work well. Of course it is difficult
to know how moist your soil is 8 feet below the surface. But if your antenna does not seem to be
working very well, you may need to water the soil around the grounding rod.

If you are not sure you will use your radio very much, you may decide to
erect a shorter outdoor antenna. I erected a temporary long wire
antenna, 11 feet from window to edge of roof, 50 feet to a tree branch
that was 7 feet off the ground, then ran the wire to the ground and tied to
a weight (total of 68 feet of wire from the window to the end of the wire).
For this antenna I did not use a grounding rod. Instead, I connected the
ground wire of the antenna coil to the ground system of the house
electrical wiring. This can be done by connecting a wire to the screw of a
faceplate for an electrical receptacle – see Figure 2 (DO NOT PUSH THE
WIRE INTO ONE OF THE RECEPTACLE SLOTS AS THIS COULD RESULT IN A
FATAL ELECTRIC SHOCK).

Using the shorter antenna and ground to faceplate, I could only hear
station WTAM 1100. After you have completed the audio amplifier for Figure 2 ground wire connected
your crystal radio, you will be able to hear more stations with the shorter to faceplate
antenna. However, if you have an interest in hearing distant stations, the
longer antenna with grounding rod will be better.

When there is a chance of an electrical storm in your area, it is advisable to disconnect your antenna at a
location outside your house. While lighting strikes on an antenna like yours are rare, it is better to be
safe and prevent the very high current and voltage from entering your house. It is best if your exterior
antenna is connected to ground outside the house when not in use.

Calibrating the Tuning Dial

The knob connected to the variable capacitor of the radio has a white pointing line to indicate the
position of the variable capacitor. The position of the variable capacitor determines the radio frequency
tuned (the station). However, the front face of the radio does not have any markings to indicate the
frequencies for various positions of the knob. Mr. La Favre will help you mark the face of the radio at
intervals of frequency. To do this we will use a signal generator. The signal generator will be connected
to a coil that will substitute for the antenna coil. The signal generator can be adjusted to any radio
frequency desired. In addition, the radio frequency can be modulated (AM - amplitude modulation)
with an audio frequency, which you can hear as a tone in the radio earphone. We will start by adjusting
the signal generator to a radio frequency of 600 kHz, modulated with an audio frequency of 400 Hz (400
Hz is a tone just a bit lower than the musical note A above middle C – that A is 440 Hz). The coil
attached to the signal generator is placed next to the tuning coil of the radio. Then the tuning knob of
the radio is adjusted until the 400 Hz tone is heard clearly in the radio earphone. The knob is adjusted
to the position where the tone is heard with the highest volume. At that point a pencil is used to place a
mark on the front plate of the radio to match the position of the white line of the tuning knob. Then
that line is labeled with the number 6 (600 kHz). We will continue by adjusting the signal generator in
increments of 100 kHz, marking each knob position for each frequency. When finished, you will have

3
Understanding and Operating your Crystal Radio – Jeffrey La Favre – March 28, 2020 – Page 4

marks on the face of the radio for 600, 700, 800, 900, 1000, 1200, 1400, and 1600 kHz. These marks will
be helpful in adjusting the variable capacitor to tune a specific station.

Figure 3: Calibrated tuning dial

Figure 4: Signal generator connected to radio


If you are working at home instead of the GEAR lab, then there is an alternative method to calibrate
your radio dial. Tune a station and wait until you learn the name of the station. They might also give
the station frequency. Then you can place a mark on the dial for that station.

Functions of the Various Components of the Crystal Radio


The most important reason for completing the Crystal Radio project is to learn how a radio works. Of
course I also hope you will enjoy using your radio. To begin, let us take a look at the schematic for the
radio provided on the next page.

4
Understanding and Operating your Crystal Radio – Jeffrey La Favre – March 28, 2020 – Page 5

L1 is the antenna coil and L2 is the


tuning coil. The antenna coil has 12
taps. The ground wire is terminated
with an alligator clip, which is used to
connect to one of the taps. After tuning
a specific station with the variable
capacitor, C1, the ground wire is
connected to the tap of coil L1 which
gives the loudest signal as heard in the
earphone. By selecting the best tap on
coil L1, you are actually tuning the
antenna to resonate at the tuned
frequency. An antenna that is tuned to
a specific radio frequency will deliver
the strongest signal to the radio. When
you adjust the variable capacitor to
tune another station, you may need to
adjust the tap connection on L1, Figure 5: schematic of the Crystal Radio
especially if the new station tuned is of
a significantly different frequency than the previously tuned station. Higher frequency stations will
require connection to a tap closer to the antenna end of the coil. As you tune stations of lower
frequency, you will need to adjust the tap connection to a tap further from the antenna end of the coil.
In other words, a station of lower frequency will require the signal to travel through more coil turns than
one of higher frequency. The exact tap to use will also depend on the length of your antenna.
Therefore, it is not possible for me to tell you which tap to use for a specific station. You will need to
establish this by trial and error. If you are not able to find a tap on the coil that provides a stronger
signal than other taps, then it is likely that your antenna is too short to tune to resonance. Nevertheless,
this will not prevent you from hearing stronger stations.

Figure 6 on the next page is a photo of the assembled radio. The antenna coil has two alligator clips
used to connect to ground and the antenna. The red wire of the antenna coil connects to the antenna
wire and the black wire connects to the ground wire. After making these connections, and placing the
antenna coil near the tuning coil, your radio is ready for use.

The audio transformer is labeled as T1 in the schematic of Figure 5. The audio transformer is used to
match the impedance of the earphone.

5
Understanding and Operating your Crystal Radio – Jeffrey La Favre – March 28, 2020 – Page 6

Figure 6: assembled crystal radio

The radio signal present in the antenna coil is transferred to the tuning coil by the magnetic field
generated by the antenna coil. When current flows through a coil, a magnetic field develops around the
coil. If another coil is placed near that coil, then the second coil is also immersed in the magnetic field
created by the first coil. This is the means for transferring the radio signal from the antenna coil to the
tuning coil.

The transfer of the signal between the coils can only occur if the current flowing in the antenna coil is
alternating current. As it happens, the current established in the antenna coil is alternating current.
When an antenna captures radio waves, the radio waves are converted to an alternating current in the
antenna circuit, which includes the antenna coil. As the current flows back and forth through the
antenna coil, the magnetic field builds and then collapses around the antenna coil. It is the changing
magnetic field which is required to transfer the electrical energy from the antenna coil to the tuning coil.
If the current flowing in the antenna coil was a constant direct current, there would be no transfer of
electrical energy to the tuning coil.

6
Understanding and Operating your Crystal Radio – Jeffrey La Favre – March 28, 2020 – Page 7

The antenna coil and tuning coil together constitute a type of transformer. Transformers play important
roles in electrical systems. The usual function of a transformer is conversion of voltage from one level to
another. There is a transformer mounted to the electric pole near our house. It converts the high
voltage (several thousand volts) of the electric line down to 240/120 volts for service to our house. In
the case of the crystal radio, we are not so much interested in converting the voltage of the signal in the
antenna circuit as just transferring that signal to the tuning coil. We could just use one coil and connect
the antenna, ground and variable capacitor to that coil. However, better results are obtained by using
separate coils to tune the antenna and then transfer that tuned signal to the tuning coil via a magnetic
field.

The antenna coil and tuning coil are mounted on separate bases so that you can adjust the distance
between the coils. There will be a specific distance between the coils that results in the strongest signal
received in the tuning coil and this may vary with the radio frequency tuned. The optimum spacing is
not necessarily the closest spacing. As part of the process of tuning a station, you should adjust the
space between the coils for maximum loudness heard in the earphone. In any case, the distance
between the coils for best transfer of signal will be similar to that seen in Figure 6 or maybe a little
closer. For example, if you place the coils 12 inches apart, there will be little signal transfer.

The variable capacitor C1 works together with the tuning coil to tune a specific
radio frequency. The tuning coil has a fixed amount of inductance and it is the
adjustment in capacitance of C1 that allows tuning of different frequencies.
Figure7 shows a simplified version of the LC circuit of the crystal radio. The
actual circuit for our radio contains a tap on the coil for diode D1 as well as
other connections. But let us concentrate only on the coil L and capacitor C.
In a certain respect the circuit of Figure 7 is an open circuit because current
cannot pass through capacitor C. To be more precise, the circuit is open as far
Figure 7 simple LC circuit
as direct current is concerned. However, we can consider the circuit closed in with coil and variable
respect of alternating current. Capacitors behave in a fashion that allows capacitor
current to flow temporarily in a circuit as the capacitor charges. With
alternating current, the current flows for a short period only in one direction, especially at radio
frequency rates. As the current charges the capacitor, current is allowed to flow in the circuit. Once the
capacitor is fully charged, current will no longer flow. What we must keep in mind is that at radio
frequencies, current flows in one direction for a very short period of time. Let us take a frequency of
1000 kHz as an example, a frequency in the middle of the AM broadcast band. That frequency is
equivalent to 1,000,000 cycles per second. Each cycle results in current flow in one direction followed
by current flow in the opposite direction. The duration of flow in one direction is only 1/2,000,000 th of a
second or 0.5 microseconds. A microsecond is one millionth of a second. That is a very short amount of
time. Even so, the electric current in the circuit in Figure 7 could travel around the circuit in much less
time than 0.5 microseconds IF we did not include the capacitor and inductor (coil).

In order to tune the circuit for resonance at a specific radio frequency, we want the capacitor to charge
and discharge at a rate that equals the frequency. If we removed the inductor (L) from the circuit, the
capacitor would charge and discharge much faster than the rate required for tuning the circuit to
resonance. By including the inductor, we slow down the rate of current flow, which in turn results in a
slower charge and discharge of the capacitor. It is the interesting behavior of an inductor (coil) that we
have employed to establish resonance. When voltage is first applied across an inductor, very little

7
Understanding and Operating your Crystal Radio – Jeffrey La Favre – March 28, 2020 – Page 8

current is allowed to flow through the coil. Instead, a magnetic field starts to build around the coil. As
time wears on (here we are talking about very little time), more
current is allowed to flow through the inductor. The degree of
hindrance in current flow by an inductor depends on the amount
of inductance of the coil. We measure this in units named
Henries, just as capacitance of a capacitor in measured in units of
the Farad. An LC circuit containing a coil of a specific value of
inductance and a capacitor of a specific value of capacitance will
be resonant at a specific radio frequency. Figure 8
Resonance can be a difficult thing to understand. Let us take the
analogy of a child on a swing. As the child swings back and forth, the parent gives a push just as the
backward movement stops. The end result of these timed pushes is that the child continues to swing.
The swinging of the child is in resonance with the pushes given by the parent and the child will continue
to swing indefinitely. Now suppose that the parent delivered the pushes while the child was still moving
backward. In this case, with each cycle of the swinging back and forth, the amount of the swing will
diminish until it ceases. In this case there is not resonance of the swinging and pushes.

The LC circuit is much the same. At a specific radio frequency, the frequency of resonance, the current
flows back and forth in the circuit, timed exactly to match the rate of capacitor charging and discharging
(the capacitor is somewhat like the parent pushing). At frequencies other than the resonance
frequency, the current flowing back and forth in the circuit does not match the charging and discharging
rate of the capacitor. Thus, the electrical energies of the non-resonant frequencies are absorbed in the
LC circuit and not passed on to the remaining circuits of the radio. It is by this method that a signal of a
specific frequency is allowed to pass through the radio while other frequency are not. If this did not
happen, then we would be hearing many radio stations at one time.

Two important characteristics of a radio are sensitivity and selectivity. Sensitivity is the ability of a radio
to deliver a sound that you can hear, derived from a weak radio signal received. Radios other than the
crystal type include some type of signal amplification so that stations with weak signals can be heard.
Sensitivity can be measured as the minimum signal voltage received that results in audible sound.
Crystal radios have poor sensitivity because they rely only on the power received from the tuned radio
waves. The efficiency of the radio antenna in capturing energy from the passing radio waves affects the
signal strength received by the radio. Since crystal radios do not amplify the signal, it is especially
important to use efficient antennas with crystal radios.

Crystal radios are also known in general for poor selectivity, although better designs have better
selectivity. It is not uncommon for more than one station to be heard at a particular setting of the
variable capacitor due to poor selectivity in the crystal radio. Nevertheless, you will be able to find some
stations that you can hear clearly without interference from another station. It just depends on the
separation in frequencies of the strong radio stations received at your location. More advanced radios,
of the kind you are familiar with, have much better selectivity and usually tune only one station at a
time, even when strong stations have frequencies very close to each other. I will not detail the reasons
for this any further at this point as the improvements in selectivity require a discussion of circuits not
found in crystal radios.

8
Understanding and Operating your Crystal Radio – Jeffrey La Favre – March 28, 2020 – Page 9

Figure 8 is a portion of the radio schematic showing part of the tuning coil, the detector diode D1 and
the audio transformer T1. Two test points are marked on the schematic. We will connect an
oscilloscope to these test points so that we can visualize the radio signal at these points in the radio.
This will help in understanding the radio.

Figure 9: oscilloscope traces at test point 1 (top trace) and test point 2
(bottom trace)
An oscilloscope is an instrument that can be used to visualize rapidly changing electric signals. Figure 9
is the oscilloscope traces at test points one and two (see Figure 8 for locations of test points). A signal
generator is connected to the radio providing a radio frequency of 1100 kHz, modulated by an audio
frequency of 400 Hz. The top trace (blue if you have a color copy of this) displays the radio frequency at
test point one modulated by the audio frequency. In the trace you can only see the waves of the audio
signal. The waves of the radio frequency are so numerous that they appear as a solid blue color. It
would be necessary to stretch the display to a great extent in the horizontal direction before we could
see the individual radio frequency waves in the top trace.

The height of the radio waves in top trace is modulated by the audio signal (amplitude modulation or
AM). The audio signal is much lower in frequency than the radio frequency (the number of audio
modulations are much fewer than the number of radio frequency waves). Notice the tab labeled “1” on
the left side of the top trace. That tab marks the position of 0 volts. Any time the wave is above the tab,
the voltage will be greater than 0. Any time the wave is below the tab, the voltage will be below 0 (a
negative voltage). The radio frequency must have alternating positive and negative voltage in order to
force periodic reversal in the direction of current flow (like quickly switching the connections to a
battery). Otherwise, the current would not change directions and it would not be alternating current.

You should notice that the bottom trace (red), representing the signal at test point two, looks very
different. Test point two is on the opposite side of the detector diode from test point one. Also note
that for this test the diode connection to the transformer T1 was disconnected. Since the diode blocks
current flow in one direction, we should not expect to see positions of negative and positive voltage on
the wave trace here. In fact, notice where the 0 volt tab with the label “2” is located. The bottoms of
the bottom trace waves are at 0 volts. All positions of the waves are at 0 volts or higher because the
diode has rectified the radio signal. We call this detection. The diode has converted the alternating

9
Understanding and Operating your Crystal Radio – Jeffrey La Favre – March 28, 2020 – Page 10

current radio signal into a pulsating direct current audio signal. It is the audio signal that we need to
apply to the earphone in order to hear the sound. If we were to just apply the radio frequency itself to
the earphone we could not hear any sound. Humans are not capable of hearing sound at a frequency
higher than 20,000 Hz.

After passing through the detector diode D1, the extracted audio signal passes through the audio
transformer. The transformer transfers the audio signal to the earphone where the electric signal is
converted into sound waves that you can hear. The transformer performs an important function in
matching the impedance requirement of the tuning circuit to the impedance requirement of the device
used to convert the electric signal to sound. The transformer has many taps that represent different
impedances. The tuning circuit is attached to the white and black wires of the transformer, which
provide about 40,000 ohms of impedance. The earphone is attached to the violet and black wires of the
transformer, which provides 10,000 ohms of impedance. This is the best impedance matching I have
found by listening to the signal in the earphone and selecting the loudest sound produced when testing
all possible connections on the transformer. If you happen to have another high impedance earphone
or headset you would like to use with your radio, you may need to use another tap on the audio
transformer to connect to the device. The black wire should always be used as one connection. The
gray wire provides 20,000 ohms, the blue wire 5,000 ohms, the green wire 2,500 ohms, the yellow wire
1,200 ohms, the orange wire 600 ohms and the red wire 300 ohms. I happen to have a very old pair of
high impedance headphones from about 1920 that are designed for crystal radios. It works well when
connected to the yellow wire of 1,200 ohms impedance. Modern headsets and earbuds are mostly low
impedance devices that will not work with the crystal radio. However, if you pass the signal through the
amplifier you will build (which has a high impedance input and low impedance output), then you can use
your modern headphones to listen to your crystal radio. The amplifier works well using the 10,000 ohm
violet wire connection to the transformer, the same as the earphone supplied with the radio kit.

Impedance is a measure of the resistance to alternating current that a device presents to a connected
signal. It is not the exact same thing as a pure resistance, which we can call ohmic resistance.
Impedance also accounts for something called reactance. Inductors (coils) have reactance, a kind of
resistance to current flow as already mentioned. Impedance is a measure of resistance that accounts
for the combined effects of ohmic resistance (like a resistor) and reactance (like a coil). In fact, the
speakers that are used in radios that you typically use employ a voice coil attached to a diaphragm to
convert an electrical signal to sound. The long length of wire used in the coil presents some ohmic
resistance to current flow. Since the wire is wound into a coil, it also presents some reactance to
current flow. Both of these are combined into a measure of resistance known as impedance. Typical
speakers have impedances of 4 or 8 ohms and require much too much power to work with a crystal
radio.

Keeping a Log for Your Radio Listening


Most people listen to radio for the programming content. However, if you are serious about radio
technology, you may wish to maintain a log of your listening. It can be fun to see how many stations you
can hear with your radio. The conditions for propagation of radio waves varies over time and it is
probable that you will hear some stations at certain times and not at other times. Therefore, you should
listen at different times of the day and night. By keeping a log, recording the stations you can hear, and

10
Understanding and Operating your Crystal Radio – Jeffrey La Favre – March 28, 2020 – Page 11

the date and time, you will create a log of your listening. From this log you may discover some
interesting trends. For example, some stations can be heard at night but not during the day.

Even though your radio is calibrated, you cannot know for sure the exact frequency for a station until
you hear an announcement of the frequency by the radio announcer. Some stations announce this
many times each hour and some do not announce their broadcast frequency very often. So it may be an
exercise in patience on your part. The strong station in Cleveland, WTAM, broadcasts on 1100 kHz and
announces their broadcast frequency several times per hour. The announcement may sound something
like this: “This is WTAM eleven hundred.” You may need to listen carefully to catch the announcement
because it is usually done fairly fast. Don’t expect to hear something like this: “This is station WTAM
broadcasting on a frequency of eleven hundred kilohertz.” You might have heard something like that 50
years ago but not today!

There are some amateur radio operators (Ham Radio) that have become big fans of the crystal radio.
They have studied the construction of crystal radios and compete with each other to design radios
capable of tuning stations from distant locations. In fact, one Ham Radio operator located in Hawaii was
able to tune a station in Cuba with his special crystal radio. In the case of the radio you have
constructed, we cannot expect that level of performance. In fact, if you hope to hear distant stations
with your crystal radio, you will probably need to use an amplifier. After you finish your crystal radio
you will build an amplifier to use with your radio. Then you will be able to tune many more local AM
stations and also distant stations at night if you have a good antenna.

There are different modes of radio wave propagation that determine which radio stations you can hear
and at what time of day or night. This also varies with the frequency of the radio signal. For long
distance reception, frequencies above those of the AM broadcast band are more useful. These
frequencies, between 2 to 30 MHz, are sometimes referred to as shortwave radio or high frequency (HF)
radio. Some of the Ham Radio bands are included in this range. International radio stations also
broadcast in this frequency range.

Radio wave propagation can be divided into two broad types called ground waves and sky waves.
Ground waves travel close to the surface of the Earth and sky waves bounce off the Earth’s upper
atmosphere (ionosphere), which allows propagation to more distant locations. The bouncing of radio
waves off the ionosphere depends on the amount of ionization. The ionization is caused by high energy
radiation (UV light) from the Sun. Therefore, there is more ionization in the upper atmosphere during
the day than at night. That is why radio propagation varies between day and night. This subject is
considerably more complex than my short description might suggest, but we will leave it at this point for
now.

During the day radio wave propagation in the AM band is generally confined to the ground wave type.
Ground waves don’t travel much farther than the horizon. The distance to the horizon depends on the
height of the radio transmitting antenna and its elevation above sea level. Nevertheless, propagation by
ground wave is usually limited to 100 miles or less.

During the night the Sun does not shine on Earth’s upper atmosphere and the degree of ionization of air
molecules and atoms decreases. With these changes, radio waves of the frequencies used in the AM
band can bounce off the ionosphere. When this happens it becomes possible to tune in AM stations
hundreds of miles from your location. Therefore, if you want to try tuning in distant stations, you will

11
Understanding and Operating your Crystal Radio – Jeffrey La Favre – March 28, 2020 – Page 12

need to try this at night. The signal strength of these stations will be weak and you will have much
better luck hearing these stations if you connect an amplifier to your crystal radio. In addition, it is
especially important to use a good outdoor antenna if you are trying to tune in distant stations.

As you build a log of listening, you may wish to gather more technical information about the distant
stations you have been able to hear. A good web site to consult is the FCC (Federal Communications
Commission) site for AM stations: https://www.fcc.gov/encyclopedia/am-query-broadcast-station-
search . The information at this site includes the location of the station’s transmitter (given in longitude
and latitude) and the amount of power used by the station. Some AM stations are required to
broadcast with lower power at night in order to avoid interfering with other radio stations operating on
the same frequency (due to longer transmission distances at night). The FCC licenses a limited number
of “clear channel” stations in various locations in the United States. These stations are required to
transmit with 50,000 watts of power day and night and these clear channel stations are the most likely
ones you will be able to hear from distant locations. There is a list of clear channels at this web site:
https://en.wikipedia.org/wiki/Clear-channel_station . Our strong AM station in Cleveland, WTAM 1100,
is a clear channel.

12

You might also like