FANS AND BLOWERS

5.1 Introduction
Fans and blowers provide air for ventilation and
industrial process requirements. Fans generate a
pressure to move air (or gases) against a resistance
caused by ducts, dampers, or other components in a fan
system. The fan rotor receives energy from a rotating
shaft and transmits it to the air.

Difference between Fans, Blowers and Compressors

Fans, blowers and compressors are differentiated by
the method used to move the air, and by the system
pressure they must operate against. As per American
Society of Mechanical Engineers (ASME) the specific
ratio - the ratio of the discharge pressure over the
suction pressure – is used for defining the fans,
blowers and compressors (see Table 5.1).

5.2 Fan Types

Fan and blower selection depends on the volume flow Centrifugal Fan: Types
rate, pressure, type of material handled, space The major types of centrifugal fan are: radial, forward
limitations, and efficiency. Fan efficiencies differ from curved and backward curved (see Figure 5.3). Radial
design to design and also by types. Typical ranges of fans are industrial workhorses because of their high
fan efficiencies are given in Table 5.2. Fans fall into static pressures (upto 1400 mm WC) and ability to
two general categories: centrifugal flow and axial flow. handle heavily contaminated airstreams. Because of
In centrifugal flow, airflow changes direction twice - their simple design, radial fans are well suited for high
once when entering and second when leaving (forward temperatures and medium blade tip speeds. Forward-
curved, backward curved or inclined, radial) (see curved fans are used in clean environments and operate
Figure 5.1). In axial flow, air enters and leaves the fan at lower temperatures. They are well suited for low tip
with no change in direction (propeller, tubeaxial, speed and high-airflow work - they are best suited for
vaneaxial) (see Figure 5.2). moving large volumes of air against relatively low
pressures. Backward-inclined fans are more efficient
than forward-curved fans. Backward-inclined fans
reach their peak power consumption and then power
demand drops off well within their useable airflow
range. Backward-inclined fans are known as "non-
overloading" because changes in static pressure do not
overload the motor.
 displacement blower. Centrifugal blowers look more
like centrifugal pumps than fans. The impeller is
typically gear-driven and rotates as fast as 15,000 rpm.
In multi-stage blowers, air is accelerated as it passes
through each impeller. In single-stage blower, air does
not take many turns, and hence it is more efficient.
Centrifugal blowers typically operate against pressures
of 0.35 to 0.70 kg/cm2 , but can achieve higher
Axial Flow Fan: Types
pressures. One characteristic is that airflow tends to
The major types of axial flow fans are: tube axial, vane
drop drastically as system pressure increases, which
axial and propeller (see Figure 5.4.)
can be a disadvantage in material conveying systems
Tubeaxial fans have a wheel inside a cylindrical
that depend on a steady air volume. Because of this,
housing, with close clearance between blade and
they are most often used in applications that are not
housing to improve airflow efficiency. The wheel turn
prone to clogging. Positive-displacement blowers have
faster than propeller fans, enabling operation under
rotors, which "trap" air and push it through housing.
high-pressures 250 – 400 mm WC. The efficiency is
Positive-displacement blowers provide a constant
up to 65%.
volume of air even if the system pressure varies. They
Vaneaxial fans are similar to tubeaxials, but with
are especially suitable for applications prone to
addition of guide vanes that improve efficiency by
clogging, since they can produce enough pressure -
directing and straightening the flow. As a result, they
typically up to 1.25 kg/cm2 - to blow clogged materials
have a higher static pressure with less dependence on
free. They turn much slower than centrifugal blowers
the duct static pressure. Such fans are used generally
(e.g. 3,600 rpm), and are often belt driven to facilitate
for pressures upto 500 mmWC. Vaneaxials are
speed changes.
typically the most energy-efficient fans available and
should be used whenever possible.
Propeller fans usually run at low speeds and moderate
temperatures. They experience a large change in
airflow with small changes in static pressure. They
handle large volumes of air at low pressure or free
delivery. Propeller fans are often used indoors as
exhaust fans. Outdoor applications include air-cooled
condensers and cooling towers. Efficiency is low –
approximately 50% or less.

5.3 Fan Performance Evaluation and Efficient System

Operation
System Characteristics
The term "system resistance" is used when referring to
The different types of fans, their characteristics and the static pressure. The system resistance is the sum of
typical applications are given in Table 5.3. static pressure losses in the system. The system
Common Blower Types resistance is a function of the configuration of ducts,
Blowers can achieve much higher pressures than fans, pickups, elbows and the pressure drops across
as high as 1.20 kg/cm2 . They are also used to produce equipment-for example back filter or cyclone. The
negative pressures for industrial vacuum systems. system resistance varies with the square of the volume
Major types are: centrifugal blower and positive- of air flowing through the system. For a given volume
of air, the fan in a system with narrow ducts and be operating under the chosen conditions
multiple short radius elbows is going to have to work (see Figure 5.6). In the many curves shown
harder to overcome a greater system resistance than it in the Figure, the curve static pressure
would in a system with larger ducts and a minimum (SP) vs. flow is especially important. The
number of long radius turns. Long narrow ducts with intersection of the system curve and the
many bends and twists will require more energy to pull static pressure curve defines the operating
the air through them. Consequently, for a given fan point. When the system resistance changes,
speed, the fan will be able to pull less air through this the operating point also changes. Once the
system than through a short system with no elbows. operating point is fixed, the power required
Thus, the system resistance increases substantially as could be found by following a vertical line
the volume of air flowing through the system that passes through the operating point to
increases; square of air flow. Conversely, resistance an intersection with the power (BHP) curve.
decreases as flow decreases. To determine what A horizontal line drawn through the
volume the fan will produce, it is therefore necessary intersection with the power curve will lead
to know the system resistance characteristics. In to the required power on the right vertical
existing systems, the system resistance can be axis. In the depicted curves, the fan
measured. In systems that have been designed, but not efficiency curve is also presented.
built, the system resistance must be calculated. System Characteristics and Fan Curves
Typically a system resistance curve (see Figure 5.5) is In any fan system, the resistance to air
generated with for various flow rates on the x-axis and flow (pressure) increases when the flow of
the associated resistance on the y-axis. air is increased. As mentioned before, it
varies as the square of the flow. The
pressure required by a system over a range
of flows can be determined and a "system
performance curve" can be developed (shown
as SC) (see Figure 5.7). This system curve
can then be plotted on the fan curve to show
the fan's actual operating point at "A"
where the two curves (N1 and SC1) intersect.
This operating point is at air flow Q1
delivered against pressure P1.

Fan Characteristics
Fan characteristics can be represented in
form of fan curve(s). The fan curve is a
performance curve for the particular fan
under a specific set of conditions. The fan
curve is a graphical representation of a
number of inter-related parameters.
Typically a curve will be developed for a
given set of conditions usually including:
fan volume, system static pressure, fan
speed, and brake horsepower required to
drive the fan under the stated conditions.
Some fan curves will also include an
efficiency curve so that a system designer
will know where on that curve the fan will