Retro-Reflex Sensor

Universal

LW86NCT3
Part Number Technical Data
Optical Data
Range 6000 mm
Reference Reflector/Reflector Foil RQ100BA
Switching Hysteresis <5%
Light Source Red Light
Polarization Filter yes
Service Life (T = +25 °C) 100000 h
Max. Ambient Light 10000 Lux
Opening Angle 5°
Two-Lens Optic yes
Electrical Data
Supply Voltage 10...30 V DC
Current Consumption (Ub = 24 V) < 40 mA
Switching Frequency 2 kHz
Response Time 250 µs
On-/Off-Delay (RS-232) 0...5 s
Temperature Drift <5%
Temperature Range -25...60 °C
Switching Output Voltage Drop < 2,5 V
NPN Switching Output/Switching Current 100 mA
Residual Current Switching Output < 50 µA
Short Circuit Protection yes
Reverse Polarity Protection yes
Stainless steel housing Overload Protection yes
Teach-in, external teach-in Lockable yes
Teach Mode NT, MT
Protection Class III
Mechanical Data
Setting Method Teach-In
Housing Material Stainless Steel
Full Encapsulation yes
Degree of Protection IP67
Connection M12 × 1; 4-pin

NPN NC
RS-232 with Adapterbox

Connection Diagram No.

Control Panel No.
Suitable Connection Equipment No. 2
Suitable Mounting Technology No.

A reflector must be used in combination with these

sensors. They can be installed in all kinds of industrial
environments thanks to ample functional reserve. Even
reflective objects can be reliably recognized through
the use of polarized light.

Complementary Products
Adapterbox A232
Reflector, Reflector Foil
Software

Photoelectronic Sensors
 Ctrl. Panel
'



 

01 = Switching Status Indicator

02 = Contamination Warning
06 = Teach Button

1 = Transmitter Diode
2 = Receiver Diode
All dimensions in mm (1 mm = 0.03937 Inch)

Legend
+ Supply Voltage + nc Not connected ENBRS422 Encoder B/ (TTL)
– Supply Voltage 0 V U Test Input ENA Encoder A
~ Supply Voltage (AC Voltage) Test Input inverted ENB Encoder B
A Switching Output (NO) W Trigger Input AMIN Digital output MIN
Ā Switching Output (NC) W– Ground for the Trigger Input AMAX Digital output MAX
V Contamination/Error Output (NO) O Analog Output AOK Digital output OK
Contamination/Error Output (NC) O– Ground for the Analog Output SY In Synchronization In
E Input (analog or digital) BZ Block Discharge SY OUT Synchronization OUT
T Teach Input A MV Valve Output OLT Brightness output
Z Time Delay (activation) a Valve Control Output + M Maintenance
S Shielding b Valve Control Output 0 V rsv Reserved
RxD Interface Receive Path SY Synchronization Wire Colors according to DIN IEC 60757
TxD Interface Send Path SY– Ground for the Synchronization BK Black
RDY Ready E+ Receiver-Line BN Brown
GND Ground S+ Emitter-Line RD Red
CL Clock Grounding OG Orange
E/A Output/Input programmable SnR Switching Distance Reduction YE Yellow
Rx+/– Ethernet Receive Path GN Green
PoE ower over Ethernet Tx+/– Ethernet Send Path BU Blue
IN Safety Input B US Interfaces-Bus A(+)/B(–) VT Violet
OSSD Safety Output La Emitted Light disengageable GY Grey
Signal Signal Output Mag Magnet activation WH White
BI_D+/– Ethernet Gigabit bidirect. data line (A-D) RES Input confirmation PK Pink
EN0 RS422 Encoder 0-pulse 0/ (TTL) EDM Contactor Monitoring GNYE Green/Yellow
PT Platinum measuring resistor ENARS422 Encoder A/Ā (TTL)

Feasible reflector distance

Reflector type, mounting distance

RQ100BA 0,02...6 m RR25_M 0,02...1,6 m

RE18040BA 0,02...3,3 m RR25KP 0,02...1,4 m
Specifications are subject to change without notice

RQ84BA 0,01...4,5 m RR21_M 0,01...1,6 m

RR84BA 0,02...4,5 m ZRAE02B01 0,02...3 m
RE9538BA 0,02...1,5 m ZRME01B01 0,02...1 m
RE6151BM 0,01...4,5 m ZRME03B01 0,02...2,8 m
RE6151BH 0,02...2,3 m ZRMR02K01 0,02...1,1 m
RR50_A 0,02...4 m ZRMS02_01 0,01...1,5 m
RE6040BA 0,02...4 m RF505 0,06...1,6 m
RE8222BA 0,01...2 m RF255 0,06...1,2 m
RR34_M 0,01...2,4 m RF508 0,06...1,6 m
IND. CONT. EQ
RE3220BM 0,01...1,6 m RF258 0,06...1,2 m
72HL / E189727
For use in class 2 circuits
RE6210BM 0,01...1,6 m ZRDF__K01 0,06...4 m