SAFETY DATA SHEET

60T - 13% Chrome Steel Wire

Section 1. Identification
GHS product identifier : 60T - 13% Chrome Steel Wire
Other means of : Not available.
identification
Product type : Solid.

Relevant identified uses of the substance or mixture and uses advised against
Not applicable.

Supplier's details : TAFA Inc. A Praxair Surface Technologies Company

146 Pembroke Rd.
Concord, NH 03301

Emergency telephone : Emergency telephone number (with hours of operation)

number (with hours of
operation)

Section 2. Hazards identification

OSHA/HCS status : This material is considered hazardous by the OSHA Hazard Communication Standard
(29 CFR 1910.1200).
Classification of the : CARCINOGENICITY - Category 2
substance or mixture

GHS label elements

Hazard pictograms :

Signal word : Warning

Hazard statements : Suspected of causing cancer.
Precautionary statements
Prevention : Obtain special instructions before use. Do not handle until all safety precautions have
been read and understood. Use personal protective equipment as required.
Response : IF exposed or concerned: Get medical attention.
Storage : Store locked up.
Disposal : Dispose of contents and container in accordance with all local, regional, national and
international regulations.
Hazards not otherwise : None known.
classified

Section 3. Composition/information on ingredients

Substance/mixture : Substance
Other means of : Not available.
identification

CAS number/other identifiers

CAS number : Not available.
Product code : 60T - 13% Chromium Steel Wire

Date of issue/Date of revision : 5/26/2015. 60T - 13% Chromium Steel Wire 1/12
60T - 13% Chrome Steel Wire

Section 3. Composition/information on ingredients

Ingredient name % CAS number
60T - 13% Chrome Steel Wire 100 -
iron 50 - 75 7439-89-6
Nickel 5 - 35 7440-02-0
chromium 5 - 32 7440-47-3
manganese 2 - 14 7439-96-5
silicon 1-5 7440-21-3
copper 1-5 7440-50-8
molybdenum 1-5 7439-98-7
Any concentration shown as a range is to protect confidentiality or is due to batch variation.
There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified as hazardous to health or the environment and hence require reporting
in this section.
Occupational exposure limits, if available, are listed in Section 8.

Section 4. First aid measures

Description of necessary first aid measures
Eye contact : Immediately flush eyes with plenty of water, occasionally lifting the upper and lower
eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10
minutes. Get medical attention.
Inhalation : Remove victim to fresh air and keep at rest in a position comfortable for breathing. If
not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial
respiration or oxygen by trained personnel. It may be dangerous to the person providing
aid to give mouth-to-mouth resuscitation. Get medical attention. If unconscious, place
in recovery position and get medical attention immediately. Maintain an open airway.
Loosen tight clothing such as a collar, tie, belt or waistband.
Skin contact : Flush contaminated skin with plenty of water. Remove contaminated clothing and
shoes. Continue to rinse for at least 10 minutes. Get medical attention. Wash clothing
before reuse. Clean shoes thoroughly before reuse.
Ingestion : Wash out mouth with water. Remove dentures if any. Remove victim to fresh air and
keep at rest in a position comfortable for breathing. If material has been swallowed and
the exposed person is conscious, give small quantities of water to drink. Stop if the
exposed person feels sick as vomiting may be dangerous. Do not induce vomiting
unless directed to do so by medical personnel. If vomiting occurs, the head should be
kept low so that vomit does not enter the lungs. Get medical attention. Never give
anything by mouth to an unconscious person. If unconscious, place in recovery position
and get medical attention immediately. Maintain an open airway. Loosen tight clothing
such as a collar, tie, belt or waistband.

Most important symptoms/effects, acute and delayed

Potential acute health effects
Eye contact : No known significant effects or critical hazards.
Inhalation : No known significant effects or critical hazards.
Skin contact : No known significant effects or critical hazards.
Ingestion : No known significant effects or critical hazards.
Over-exposure signs/symptoms
Eye contact : No specific data.
Inhalation : No specific data.
Skin contact : No specific data.
Ingestion : No specific data.

Indication of immediate medical attention and special treatment needed, if necessary

Notes to physician : Treat symptomatically. Contact poison treatment specialist immediately if large
quantities have been ingested or inhaled.
Specific treatments : No specific treatment.
Date of issue/Date of revision : 5/26/2015. 60T - 13% Chromium Steel Wire 2/12
60T - 13% Chrome Steel Wire

Section 4. First aid measures

Protection of first-aiders : No action shall be taken involving any personal risk or without suitable training. It may
be dangerous to the person providing aid to give mouth-to-mouth resuscitation.

See toxicological information (Section 11)

Section 5. Fire-fighting measures

Extinguishing media
Suitable extinguishing : Use an extinguishing agent suitable for the surrounding fire.
media
Unsuitable extinguishing : None known.
media

Specific hazards arising : No specific fire or explosion hazard.

from the chemical
Hazardous thermal : Decomposition products may include the following materials:
decomposition products metal oxide/oxides

Special protective actions : Promptly isolate the scene by removing all persons from the vicinity of the incident if
for fire-fighters there is a fire. No action shall be taken involving any personal risk or without suitable
training.
Special protective : Fire-fighters should wear appropriate protective equipment and self-contained breathing
equipment for fire-fighters apparatus (SCBA) with a full face-piece operated in positive pressure mode.

Section 6. Accidental release measures

Personal precautions, protective equipment and emergency procedures
For non-emergency : No action shall be taken involving any personal risk or without suitable training.
personnel Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. Do not touch or walk through spilled material. Provide adequate ventilation.
Wear appropriate respirator when ventilation is inadequate. Put on appropriate
personal protective equipment.
For emergency responders : If specialised clothing is required to deal with the spillage, take note of any information
in Section 8 on suitable and unsuitable materials. See also the information in "For non-
emergency personnel".

Environmental precautions : Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains
and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air).

Methods and materials for containment and cleaning up

Small spill : Move containers from spill area. Avoid dust generation. Do not dry sweep. Vacuum
dust with equipment fitted with a HEPA filter and place in a closed, labeled waste
container. Dispose of via a licensed waste disposal contractor.
Large spill : Move containers from spill area. Approach release from upwind. Prevent entry into
sewers, water courses, basements or confined areas. Avoid dust generation. Do not
dry sweep. Vacuum dust with equipment fitted with a HEPA filter and place in a closed,
labeled waste container. Dispose of via a licensed waste disposal contractor. Note:
see Section 1 for emergency contact information and Section 13 for waste disposal.

Section 7. Handling and storage

Precautions for safe handling

Date of issue/Date of revision : 5/26/2015. 60T - 13% Chromium Steel Wire 3/12
60T - 13% Chrome Steel Wire

Section 7. Handling and storage

Protective measures : Put on appropriate personal protective equipment (see Section 8). Avoid exposure -
obtain special instructions before use. Do not handle until all safety precautions have
been read and understood. Do not get in eyes or on skin or clothing. Do not ingest. If
during normal use the material presents a respiratory hazard, use only with adequate
ventilation or wear appropriate respirator. Keep in the original container or an approved
alternative made from a compatible material, kept tightly closed when not in use. Empty
containers retain product residue and can be hazardous. Do not reuse container.
Advice on general : Eating, drinking and smoking should be prohibited in areas where this material is
occupational hygiene handled, stored and processed. Workers should wash hands and face before eating,
drinking and smoking. Remove contaminated clothing and protective equipment before
entering eating areas. See also Section 8 for additional information on hygiene
measures.

Conditions for safe storage, : Store in accordance with local regulations. Store in original container protected from
including any direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials
incompatibilities (see Section 10) and food and drink. Store locked up. Keep container tightly closed
and sealed until ready for use. Containers that have been opened must be carefully
resealed and kept upright to prevent leakage. Do not store in unlabeled containers.
Use appropriate containment to avoid environmental contamination.

Section 8. Exposure controls/personal protection

Control parameters
Occupational exposure limits
Ingredient name Exposure limits
Nickel ACGIH TLV (United States, 6/2013).
TWA: 1.5 mg/m³ 8 hours. Form: Inhalable
fraction
OSHA PEL 1989 (United States, 3/1989).
TWA: 1 mg/m³, (as Ni) 8 hours.
NIOSH REL (United States, 10/2013).
TWA: 0.015 mg/m³, (as Ni) 10 hours.
OSHA PEL (United States, 2/2013).
TWA: 1 mg/m³, (as Ni) 8 hours.
chromium ACGIH TLV (United States, 6/2013).
TWA: 0.5 mg/m³, (measured as Cr) 8 hours.
OSHA PEL 1989 (United States, 3/1989).
TWA: 1 mg/m³ 8 hours.
NIOSH REL (United States, 10/2013).
TWA: 0.5 mg/m³ 8 hours.
OSHA PEL (United States, 2/2013).
TWA: 1 mg/m³, (as Cr) 8 hours.
manganese OSHA PEL 1989 (United States, 3/1989).
TWA: 1 mg/m³, (as Mn) 8 hours. Form: Fume
STEL: 3 mg/m³, (as Mn) 15 minutes. Form:
Fume
NIOSH REL (United States, 10/2013).
TWA: 1 mg/m³, (as Mn) 10 hours. Form:
Fume
STEL: 3 mg/m³, (as Mn) 15 minutes. Form:
Fume
OSHA PEL (United States, 2/2013).
CEIL: 5 mg/m³, (as Mn) Form: Fume
ACGIH TLV (United States, 6/2013).
TWA: 0.1 mg/m³, (as Mn) 8 hours. Form:
Inhalable fraction
TWA: 0.02 mg/m³, (as Mn) 8 hours. Form:
Respirable fraction
silicon OSHA PEL 1989 (United States, 3/1989).
TWA: 5 mg/m³ 8 hours. Form: Respirable
fraction
Date of issue/Date of revision : 5/26/2015. 60T - 13% Chromium Steel Wire 4/12
60T - 13% Chrome Steel Wire

Section 8. Exposure controls/personal protection

TWA: 10 mg/m³ 8 hours. Form: Total dust
NIOSH REL (United States, 10/2013).
TWA: 5 mg/m³ 10 hours. Form: Respirable
fraction
TWA: 10 mg/m³ 10 hours. Form: Total
OSHA PEL (United States, 2/2013).
TWA: 5 mg/m³ 8 hours. Form: Respirable
fraction
TWA: 15 mg/m³ 8 hours. Form: Total dust
copper ACGIH TLV (United States, 6/2013).
TWA: 1 mg/m³, (as Cu) 8 hours. Form: Dust
and mist
TWA: 0.2 mg/m³ 8 hours. Form: Fume
OSHA PEL 1989 (United States, 3/1989).
TWA: 1 mg/m³, (as Cu) 8 hours. Form:
Dusts and Mists
TWA: 0.1 mg/m³, (as Cu) 8 hours. Form:
Fume
NIOSH REL (United States, 10/2013).
TWA: 1 mg/m³, (as Cu) 10 hours. Form:
Dusts and Mists
OSHA PEL (United States, 2/2013).
TWA: 1 mg/m³ 8 hours. Form: Dusts and
Mists
TWA: 0.1 mg/m³ 8 hours. Form: Fume
molybdenum ACGIH TLV (United States, 6/2013).
TWA: 10 mg/m³, (as Mo) 8 hours. Form:
Inhalable fraction
TWA: 3 mg/m³, (as Mo) 8 hours. Form:
Respirable fraction

Appropriate engineering : If user operations generate dust, fumes, gas, vapor or mist, use process enclosures,
controls local exhaust ventilation or other engineering controls to keep worker exposure to
airborne contaminants below any recommended or statutory limits.
Environmental exposure : Emissions from ventilation or work process equipment should be checked to ensure
controls they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process equipment
will be necessary to reduce emissions to acceptable levels.

Individual protection measures

Hygiene measures : Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Wash contaminated clothing before reusing. Ensure that eyewash stations and safety
showers are close to the workstation location.
Eye/face protection : Safety eyewear complying with an approved standard should be used to avoid exposure
to liquid splashes, mists, gases or dusts. If contact is possible, the following protection
should be worn, unless the assessment indicates a higher degree of protection: safety
glasses with side-shields.
Skin protection
Hand protection : Chemical-resistant, impervious gloves complying with an approved standard should be
worn at all times when handling chemical products. Considering the parameters
specified by the glove manufacturer, check during use that the gloves are still retaining
their protective properties. It should be noted that the time to breakthrough for any
glove material may be different for different glove manufacturers. In the case of
mixtures, consisting of several substances, the protection time of the gloves cannot be
accurately estimated.
Body protection : Personal protective equipment for the body should be selected based on the task being
performed and the risks involved and should be approved by a specialist before
handling this product.

Date of issue/Date of revision : 5/26/2015. 60T - 13% Chromium Steel Wire 5/12
60T - 13% Chrome Steel Wire

Section 8. Exposure controls/personal protection

Other skin protection : Appropriate footwear and any additional skin protection measures should be selected
based on the task being performed and the risks involved and should be approved by a
specialist before handling this product.
Respiratory protection : Use a properly fitted, particulate filter respirator complying with an approved standard if
a risk assessment indicates this is necessary. Respirator selection must be based on
known or anticipated exposure levels, the hazards of the product and the safe working
limits of the selected respirator.

Section 9. Physical and chemical properties

Appearance
Physical state : Solid. [Wire]
Color : Silvery.
Odor : Odorless.
Odor threshold : Not available.
pH : Not available.
Melting point : 1427°C (2600.6°F)
Boiling point : Not available.
Flash point : Not available.
Evaporation rate : Not available.
Flammability (solid, gas) : Not available.
Lower and upper explosive : Not available.
(flammable) limits
Vapor pressure : Not available.
Vapor density : Not available.
Relative density : 7.83
Solubility : Insoluble in the following materials: cold water and hot water.
Partition coefficient: n- : Not available.
octanol/water
Auto-ignition temperature : Not available.
Decomposition temperature : Not available.
Viscosity : Not available.
VOC content : 0 lbs/gal (0 g/l)

Section 10. Stability and reactivity

Reactivity : No specific test data related to reactivity available for this product or its ingredients.

Chemical stability : The product is stable.

Possibility of hazardous : Under normal conditions of storage and use, hazardous reactions will not occur.
reactions

Conditions to avoid : No specific data.

Incompatible materials : No specific data.

Hazardous decomposition : Under normal conditions of storage and use, hazardous decomposition products should
products not be produced.

Date of issue/Date of revision : 5/26/2015. 60T - 13% Chromium Steel Wire 6/12
60T - 13% Chrome Steel Wire

Section 11. Toxicological information

Information on toxicological effects
Acute toxicity
Product/ingredient name Result Species Dose Exposure
manganese LD50 Oral Rat 9 g/kg -
silicon LD50 Oral Rat 3160 mg/kg -
Irritation/Corrosion
Product/ingredient name Result Species Score Exposure Observation
manganese Eyes - Mild irritant Rabbit - 24 hours 500 -
milligrams
Skin - Mild irritant Rabbit - 24 hours 500 -
milligrams
silicon Eyes - Mild irritant Rabbit - 3 milligrams -
Sensitization
Not available.
Mutagenicity
Not available.
Carcinogenicity
Not available.
Classification
Product/ingredient name OSHA IARC NTP
Nickel - 2B Reasonably anticipated to be a human carcinogen.
chromium - 3 -
Reproductive toxicity
Not available.

Teratogenicity
Not available.

Specific target organ toxicity (single exposure)

Not available.
Specific target organ toxicity (repeated exposure)
Not available.
Aspiration hazard
Not available.

Information on the likely : Not available.

routes of exposure
Potential acute health effects
Eye contact : No known significant effects or critical hazards.
Inhalation : No known significant effects or critical hazards.
Skin contact : No known significant effects or critical hazards.
Ingestion : No known significant effects or critical hazards.

Symptoms related to the physical, chemical and toxicological characteristics

Eye contact : No specific data.
Inhalation : No specific data.
Skin contact : No specific data.
Ingestion : No specific data.

Date of issue/Date of revision : 5/26/2015. 60T - 13% Chromium Steel Wire 7/12
60T - 13% Chrome Steel Wire

Section 11. Toxicological information

Delayed and immediate effects and also chronic effects from short and long term exposure
Short term exposure
Potential immediate : Not available.
effects
Potential delayed effects : Not available.
Long term exposure
Potential immediate : Not available.
effects
Potential delayed effects : Not available.
Potential chronic health effects
Not available.

General : No known significant effects or critical hazards.

Carcinogenicity : Suspected of causing cancer. Risk of cancer depends on duration and level of
exposure.
Mutagenicity : No known significant effects or critical hazards.
Teratogenicity : No known significant effects or critical hazards.
Developmental effects : No known significant effects or critical hazards.
Fertility effects : No known significant effects or critical hazards.

Numerical measures of toxicity

Acute toxicity estimates
Route ATE value
Oral 31073.3 mg/kg

Section 12. Ecological information

Toxicity
Product/ingredient name Result Species Exposure
iron Acute EC50 3700 µg/l Fresh water Aquatic plants - Lemna minor 4 days
Acute LC50 33000 to 100000 µg/l Crustaceans - Crangon crangon 48 hours
Marine water
Acute LC50 6.48 µg/l Marine water Fish - Periophthalmus waltoni - 96 hours
Adult
Chronic NOEC 100 mg/l Marine water Algae - Glenodinium halli 72 hours
Nickel Acute EC50 2 ppm Marine water Algae - Macrocystis pyrifera - 4 days
Young
Acute EC50 450 µg/l Fresh water Aquatic plants - Lemna minor 4 days
Acute EC50 1000 µg/l Marine water Daphnia - Daphnia magna 48 hours
Acute IC50 0.31 mg/l Marine water Crustaceans - Americamysis 48 hours
bahia - Juvenile (Fledgling,
Hatchling, Weanling)
Acute LC50 47.5 ng/L Fresh water Fish - Heteropneustes fossilis 96 hours
Chronic NOEC 100 mg/l Marine water Algae - Glenodinium halli 72 hours
Chronic NOEC 3.5 µg/l Fresh water Fish - Cyprinus carpio 4 weeks
chromium Acute EC50 0.2 ppm Marine water Algae - Bacillariophyta 72 hours
Acute EC50 5 ppm Marine water Algae - Macrocystis pyrifera - 4 days
Young
Acute EC50 35000 µg/l Fresh water Aquatic plants - Lemna minor 4 days
Acute LC50 45 µg/l Fresh water Crustaceans - Ceriodaphnia 48 hours
reticulata
Acute LC50 22 µg/l Fresh water Daphnia - Daphnia magna 48 hours
Acute LC50 13.9 ppm Fresh water Fish - Anguilla rostrata 96 hours
Date of issue/Date of revision : 5/26/2015. 60T - 13% Chromium Steel Wire 8/12
60T - 13% Chrome Steel Wire

Section 12. Ecological information

Chronic NOEC 50 mg/l Marine water Algae - Glenodinium halli 72 hours
Chronic NOEC 0.19 µg/l Fresh water Fish - Cyprinus carpio 4 weeks
manganese Acute EC50 31000 µg/l Fresh water Aquatic plants - Lemna minor 4 days
Acute LC50 29000 µg/l Daphnia - Daphnia magna 48 hours
Acute LC50 28 mg/l Fresh water Fish - Pimephales promelas 96 hours
copper Acute EC50 1100 µg/l Fresh water Aquatic plants - Lemna minor 4 days
Acute EC50 2.1 µg/l Fresh water Daphnia - Daphnia longispina - 48 hours
Juvenile (Fledgling, Hatchling,
Weanling)
Acute IC50 13 µg/l Fresh water Algae - Pseudokirchneriella 72 hours
subcapitata - Exponential growth
phase
Acute IC50 5.4 mg/l Marine water Aquatic plants - Plantae - 72 hours
Exponential growth phase
Acute LC50 0.072 µg/l Marine water Crustaceans - Amphipoda - Adult 48 hours
Acute LC50 7.56 µg/l Marine water Fish - Periophthalmus waltoni - 96 hours
Adult
Chronic NOEC 2.5 µg/l Marine water Algae - Nitzschia closterium - 72 hours
Exponential growth phase
Chronic NOEC 7 mg/l Fresh water Aquatic plants - Ceratophyllum 3 days
demersum
Chronic NOEC 0.02 mg/l Fresh water Crustaceans - Cambarus bartonii 21 days
- Mature
Chronic NOEC 2 µg/l Fresh water Daphnia - Daphnia magna 21 days
Chronic NOEC 0.8 µg/l Fresh water Fish - Oreochromis niloticus - 6 weeks
Juvenile (Fledgling, Hatchling,
Weanling)
molybdenum Acute LC50 200000 µg/l Daphnia - Daphnia magna 48 hours
Acute LC50 800 mg/l Fresh water Fish - Oncorhynchus mykiss 96 hours
Chronic NOEC 500 mg/l Marine water Algae - Glenodinium halli 72 hours

Persistence and degradability

Not available.

Bioaccumulative potential
Product/ingredient name LogPow BCF Potential
silicon 57 to 77 - high

Mobility in soil
Soil/water partition : Not available.
coefficient (KOC)

Other adverse effects : No known significant effects or critical hazards.

Section 13. Disposal considerations

Disposal methods : The generation of waste should be avoided or minimized wherever possible. Disposal
of this product, solutions and any by-products should at all times comply with the
requirements of environmental protection and waste disposal legislation and any
regional local authority requirements. Dispose of surplus and non-recyclable products
via a licensed waste disposal contractor. Waste should not be disposed of untreated to
the sewer unless fully compliant with the requirements of all authorities with jurisdiction.
Waste packaging should be recycled. Incineration or landfill should only be considered
when recycling is not feasible. This material and its container must be disposed of in a
safe way. Care should be taken when handling emptied containers that have not been
cleaned or rinsed out. Empty containers or liners may retain some product residues.
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains
and sewers.

Date of issue/Date of revision : 5/26/2015. 60T - 13% Chromium Steel Wire 9/12
60T - 13% Chrome Steel Wire

Section 14. Transport information

DOT TDG Mexico ADR/RID IMDG IATA
Classification Classification Classification
UN number Not regulated. Not regulated. Not regulated. Not regulated. Not regulated. Not regulated.

UN proper - - - - - -
shipping name
Transport - - - - - -
hazard class(es)

Packing group - - - - - -
Environmental No. No. No. No. No. No.
hazards
Additional Reportable - - - - -
information quantity
500 lbs / 227 kg
Package sizes
shipped in
quantities less
than the
product
reportable
quantity are
not subject to
the RQ
(reportable
quantity)
transportation
requirements.

Special precautions for user : Transport within user’s premises: always transport in closed containers that are
upright and secure. Ensure that persons transporting the product know what to do in the
event of an accident or spillage.

Transport in bulk according : Not available.

to Annex II of MARPOL
73/78 and the IBC Code

Section 15. Regulatory information

U.S. Federal regulations : TSCA 8(a) CDR Exempt/Partial exemption: Not determined
All components are listed or exempted.
Clean Water Act (CWA) 307: Nickel; chromium; copper

Clean Air Act Section 112 : Listed

(b) Hazardous Air
Pollutants (HAPs)
Clean Air Act Section 602 : Not listed
Class I Substances
Clean Air Act Section 602 : Not listed
Class II Substances
DEA List I Chemicals : Not listed
(Precursor Chemicals)

Date of issue/Date of revision : 5/26/2015. 60T - 13% Chromium Steel Wire 10/12
60T - 13% Chrome Steel Wire

Section 15. Regulatory information

DEA List II Chemicals : Not listed
(Essential Chemicals)
SARA 302/304
Composition/information on ingredients
No products were found.

SARA 304 RQ : Not applicable.

SARA 311/312
Classification : Delayed (chronic) health hazard
Composition/information on ingredients
Name % Fire Sudden Reactive Immediate Delayed
hazard release of (acute) (chronic)
pressure health health
hazard hazard
60T - 13% Chrome Steel Wire 100 No. No. No. No. Yes.
Nickel 5 - 35 No. No. No. No. Yes.
silicon 1-5 No. No. No. Yes. No.
SARA 313
Product name CAS number %
Form R - Reporting Nickel 7440-02-0 5 - 35
requirements chromium 7440-47-3 5 - 32
manganese 7439-96-5 2 - 14
copper 7440-50-8 1-5
Supplier notification Nickel 7440-02-0 5 - 35
chromium 7440-47-3 5 - 32
manganese 7439-96-5 2 - 14
copper 7440-50-8 1-5
SARA 313 notifications must not be detached from the SDS and any copying and redistribution of the SDS shall include
copying and redistribution of the notice attached to copies of the SDS subsequently redistributed.
State regulations
Massachusetts : The following components are listed: NICKEL; CHROMIUM; MANGANESE;
MOLYBDENUM; COPPER; SILICON DUST
New York : The following components are listed: Nickel; Chromium; Copper
New Jersey : The following components are listed: NICKEL; CHROMIUM; MANGANESE;
MOLYBDENUM; COPPER; SILICON
Pennsylvania : The following components are listed: NICKEL; CHROMIUM; MANGANESE;
MOLYBDENUM; COPPER FUME; SILICON
California Prop. 65
WARNING: This product contains a chemical known to the State of California to cause cancer.
Ingredient name Cancer Reproductive No significant risk Maximum
level acceptable dosage
level
Nickel Yes. No. No. No.
International regulations
Chemical Weapon Convention List Schedules I, II & III Chemicals
Not listed.
Montreal Protocol (Annexes A, B, C, E)
Not listed.
Stockholm Convention on Persistent Organic Pollutants
Not listed.

Date of issue/Date of revision : 5/26/2015. 60T - 13% Chromium Steel Wire 11/12
 60T - 13% Chrome Steel Wire

Section 15. Regulatory information

Rotterdam Convention on Prior Inform Consent (PIC)
Not listed.
UNECE Aarhus Protocol on POPs and Heavy Metals
Not listed.
International lists
National inventory
Australia : All components are listed or exempted.
Canada : All components are listed or exempted.
China : All components are listed or exempted.
Europe : All components are listed or exempted.
Japan : Not determined.
Malaysia : Not determined.
New Zealand : All components are listed or exempted.
Philippines : All components are listed or exempted.
Republic of Korea : All components are listed or exempted.
Taiwan : Not determined.

Section 16. Other information

History
Date of printing : 5/26/2015.
Date of issue/Date of : 5/26/2015.
revision
Key to abbreviations : ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL 73/78 = International Convention for the Prevention of Pollution From Ships,
1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution)
UN = United Nations
References : Not available.
Notice to reader
To the best of our knowledge, the information contained herein is accurate. However, neither the above-named
supplier, nor any of its subsidiaries, assumes any liability whatsoever for the accuracy or completeness of the
information contained herein.
Final determination of suitability of any material is the sole responsibility of the user. All materials may present
unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot
guarantee that these are the only hazards that exist.

Date of issue/Date of revision : 5/26/2015. 60T - 13% Chromium Steel Wire 12/12