www.longhe.

asia

ATTACHMENTS LINE UP
Primary Crusher I Secondary Crusher I Shear I Vibro Ripper I Vibro Hammer I Bucket Crusher I Auger Drill CRUSHER I VIBRO RIPPER & HAMMER I BUCKET CRUSHER
Orange Grapple I Clam Shell I Quick Coupler I Compactor I Screener I Grapple I Vibrating Bucket AUGER DRILL I QUICK COUPLER I OTHER ATTACHMENTS
Multi Grapple I Bucket I Ripper I Double & Multi Ripper I Lifting Fork I Pedestal Boom Breaker

Contact:
Longhe Asia Pte Ltd PT. Longhe Asia Indonesia
115A Commonwealth Drive, #03-14 88 Tower, Level 38, Tower A,
Tanglin Halt Industrial Estate Singapore 149596 Jl. Casablanca Raya Kav. 88
Tel: +65 6255 0250 Jakarta – 12870, Indonesia
Email: [email protected] Email: [email protected]
www.longhe.asia Mobile: +628117000559
www.longhe.asia
CRUSHER SHEAR

Primary Crusher
>>>Feature
•Dual cylinder and dual pin

Height
•Wide jaw opening and high crushing force
•360° hydraulic rotation motor with dual relief valve
•The structure is manufactured from high-strength, abrasion-resistant steel A
B

Model Unit HPC 03V HPC 05V HPC 15V HPC 20V HPC 25V HPC 30V HPC 45V
C
Opening
Width
Applicable Carrier Unit 2~3 5~7 12~15 17~23 20~30 30~40 45~65
Operating Weight ton 290 580 1250 1580 2100 2750 5350
Jaw Opening kg 420 620 750 890 980 1100 1400
Blade Length mm 80 100 140 190 220 250 250
Cutting Force A. Throat 90 166 493 1116 837 1729 2558

Crushing Force
B. Middle Metric ton
C. Tip
35
22
52
39
133
77
202
111
244
143
326
180
482
266
Shear
Rated Pressure bar 210 300 300 320 320 320 320 >>>Feature
Rated Oil Flow lpm 120 160 180 230 240 260 380 •Single pin and dual cylinder
Height mm 1000 1200 1620 2100 2280 2450 2850 •Zero slip between two jaws
Dimension
Width mm 740 900 1120 1280 1450 1720 2350 •360° hydraulic rotation motor with dual relief valve C
B g
Pressure bar 110 110 210 210 210 210 210 •Optimized angle and continuos force through the cycle

Width
n
A i
n
Hydraulic e
p

Oil Flow lpm 15-20 15~20 28~32 40~55 32~45 32~45 75~105 O
Rotation
Speed rpm 10~15 10~15 10~15 10~15 10~15 10~15 10~15 Model Unit HS 400RV HS 500RV HS 600RV HS 700RV
Open sec 1.5 1.5 1.8 2.1 2.9 3.4 4.3 Applicable Carrier Unit 12~14 20~30 28~45 42-52
Height
Cycle Time
Close sec 1.5 1.5 1.7 2.3 2.7 4.1 5.5 Operating Weight ton 1350 2200 3100 5200
※ The above specifications are subject to change without prior notice for quality improvement. Jaw Opening kg 400 490 530 700
Blade Length mm 380 585 680 890
Secondary Crusher Cutting Force A. Throat 330 996 1360 3400
B. Middle Metric ton 200 269 413 540
>>>Feature Crushing Force
C. Tip 110 156 244 290
•Wide jaw opening
H
e

g
h
t
i

Rated Pressure bar 300 320 320 320

•Speed up valve reduces the cycle time of jaw
Rated Oil Flow lpm 180 230 260 380
•Cylinder rod is protected by heavy duty guard
A Height 2070 3200
•The structure is manufactured from high-strength, abrasion-resistant steel mm 1600 2390
D B
Dimension
e
pt Width mm 820 1150 1350 1500
h
C Model Unit HSC 03V HSC 05V HSC 15V HSC 20V HSC 25V HSC 30V HSC 45V Pressure bar 170 210 210 210
g
e
n
in Applicable Carrier ton 2~5 5~9 10~18 18~22 20~30 30~40 45~65 Hydraulic
p
O Oil Flow lpm 40-70 50~90 120~170 120-170
Operating Weight kg 350 580 950 1500 1950 2750 4200 Rotation
Length Width Speed rpm 18-22 10~15 10~15 10~15
Jaw Opening mm 430 620 700 850 950 1100 1500
Open sec 1.8 2.8 3.5 2.8
Jaw Depth mm 360 570 820 825 870 1050 1470 Cycle Time
Close sec 1.8 2.6 4.2 3
Blade Length mm 75 102 140 150 200 200 250
※ The above specifications are subject to change without prior notice for quality improvement.
A. Throat 65 83 163 191 202 290 366
Cutting Force B. Middle Metric ton 27 37 67 91 95 156 180
C. Tip 18 25 42 60 62 110 150
Rated Pressure bar 180 280 320 320 320 320 320
Rated Oil Flow lpm 120 180 160 230 240 320 380
Height mm 994 1400 1650 1830 1960 2350 2900
Dimension
Length mm 1100 1150 1230 1250 1420 1620 1920
Width mm 400 410 436 520 540 600 800
Open sec 2 1.9 1.9 2.0 2.5 2.5 3.7
Cycle Time
Close sec 2 2 1.9 2.1 2.2 2.3 3.2
※ The above specifications are subject to change without prior notice for quality improvement.
VIBRO RIPPER VIBRO HAMMER

>>>Feature >>>Feature
•Low maintenance •Lower cost of maintenance than crane hammer.
•Environment friendly •Outstanding workability and mobility.
•Lower cost per cubic meter produced •Easier operate in critical regions such as chaotic section of city,
•Low noise level, Suitable for city & public works bridge area and the vicinity of high-voltage wires than crane hammer does.
•Productivity : Up to 3~4 times compare to equivalent breakers •Equipped with high-powered hydraulic piston motor
•Suitable for Sedimentary materials, Gypsum, Concrete, and suitable bearing for high frequency vibration.
Slate, Marble, Gneiss, Sandstone, Limestone,,, •Install vibro isolating rubber for high frequency purpose.
•Easy connect and disconnect the hammer by the use
of excavator’s breaker hydraulic lines.
•The clamping lug can handle and move construction objects easily.
Housing
•Pile driving power 20% up compared to the existing equipments.
Top Bracket
•Sufficient wear-resistant design and 360-degree revolution.
Upper, Under Link
Control Valve
IN, OUT Port

Hydraulic Motor Bearing

Drain Port

Upper, Under Link Motor

Productivity Vibro Ripper/Hydraulic Breaker Electrical parts

Body

Vibro isolating rubber

Tooth

Hook
Hardness in Mpa

Control valve
Description Unit HVR 06 HVR 08 HVR 10 HVR 14 HVR 20
B
Applicable carrier ton 12~16 20~26 22~30 30~39 40~55
C
Description Unit HVH 08 HVH 10 HVH 14
Ripper kg 1500 2500 3150 4600 5600 Carrier ton 20~28 28~34 33~40
Weight
Tooth kg 15 21 32 32 61 Hammer kg 1600 1800 1900
Weight
A mm 1650 2116 2433 3250 3300 Extension boom kg 600 700 700
B mm 870 1309 1300 2140 2260 Clamping Jaw mm 65 65 65

L
Dimension
A

C mm 500 705 800 1100 1150 Frequency bpm 2000~2500 2000~2500 2000~2500
F

D mm 900 1100 1260 1680 1800 Slewing Degree degree 360 360 360

H
Operating Pressure bar 180~200 210~240 240~250 240~250 240~250 Dimension (L×W×H) mm 1857 × 1042 × 650 1959 × 1103 × 792 2016 × 1196 × 830
D

Oil Flow lpm 100~150 170~190 180~200 200~220 250~260 Oil Flow lpm 130~180 170~200 200~260
W
Frequency bpm 1500 1500 1400 1200 1100 Operating Pressure bar 180~200 200~250 200~250
※ The above specifications are subject to change without prior notice for quality improvement. ※ The above specifications are subject to change without prior notice for quality improvement.
BUCKET CRUSHER AUGER DRILL

>>>Advantages >>>Feature
•Perfect for on-site crushing of all types of demolition materials Earth Auger is a kind of post hold machine.
•Fitted to the excavators and working by the hydraulic system It can be mounted to all common hydraulic excavators as well as Fored hood ears :
Deal with the heavy strain of daily use.
•Reduces the use of mechanical pieces of equipment skid steer loader, backhoe loader telescopic handler, wheel
All hold pins are locked for extra safety
•Solves the problem of having to dispose of Loader and other machinery.
demolition materials by taking them to a dump
Hose & couple options :
•Eliminates all leasing costs Tooth locking System
Absolutely high quality
•Cuts down on transportation and management costs
Rock Type : Hydraulic motors :
•Comfortable, simple to use and fast It fit to rock, pitch or a
Imported from USA Developing Old Hood Ear
lot of gravel land.
•Suited for small and large worksites the most reliable attachments
Harder than tungsten type.
•Allows materials to be recycled, resulting
Tungsten Type :
in significant savings It fit to clay, snady ERICYUC gearbox :
land or a little gravel. Unique planetary gearbox Multiplied
Digging the soil land very easily.
output torque Extreme efficency New Hood Ear
>>>Application Fields
•Demolitions
•Roads Construction
•Excavations
•Quarries and Mines
•Environmental Remediations
•Vineyard Deep-Plowing

HBC 08
HBC 10
HBC 14

Model Unit HAD 2000 HAD 2500 HAD 3000 HAD 3500 HAD 4500 HAD 5000 HAD 5500 HAD 6000 HAD 7000 HAD 8000 HAD10000 HAD12000 HAD15000 HAD20000 HAD25000

Carrier ton 1~2.5 1.5~3 2~3.5 2.5~4.5 3~5 4.5~7 5~7 6~8 7~10 8~12 10~13 13~17 13~17 13~17 15~23
Torque N.m ≤1872 ≤2432 ≤2877 ≤3614 ≤4218 ≤5056 ≤5910 ≤6150 ≤6931 ≤8048 ≤10778 ≤11976 ≤15046 ≤19039 ≤24949
Setting(mm) 10 20 30 40 50 60 70 80 90 10 110 Pressure Bar 205 205 240 240 240 240 240 240 240 240 240 240 240 240 250
HBC 08 4 7 11 15 18 22 26 29 34 37 40 Oil Flow Range l/min 23~53 30~61 30~61 30~68 38~76 38~76 45~83 45~106 61~121 61~136 70~136 80~140 80~151 80~170 90~180
HBC 10 5 10 14 18 21 25 29 33 38 42 45 Rotary Speed rpm 40~92 40~82 40~81 32~72 32~64 29~58 28~50 34~80 37~72 29~64 26~45 22~43 20~39 17~34 16~30
HBC 14 8 13 18 22 26 30 35 39 43 47 52 Hydraulic Hose inch 1/2 1/2 1/2 1/2 1/2 1/2 1/2 3/4 3/4 3/4 3/4 1 1 1 1
Output Shaft mm Ø65 Ø65 Ø65 Ø65 Ø65 Ø75 Ø75 Ø75 Ø75 Ø75 Ø75 Ø75 Ø75 Ø75 Ø75
Description Unit HBC 08 HBC 10 HBC 14 Unit Weight kg 54 54 71 71 71 108 108 110 112 115 167 167 167 185 185
Applicable Carrier ton 20~25 26~35 36~45 Unit Height mm 595 595 700 700 700 780 780 850 850 850 930 930 930 930 930
3 Unit Max. Dia mm 200 200 244 244 244 269 269 269 269 269 290 290 290 290 290
Load Capacity m 0.65 0.8 1
Operating Pressure Mpa 20 20 20 Single Pin Hitch Single Pin Hitch Single Pin Hitch Single Pin Hitch Single Pin Hitch Single Pin Hitch Single Pin Hitch Single Pin Hitch Single Pin Hitch Single Pin Hitch Single Pin Hitch Single Pin Hitch Single Pin Hitch Single Pin Hitch Single Pin Hitch
Hitch options Double Pin Hitch Double Pin Hitch Double Pin Hitch Double Pin Hitch Double Pin Hitch Double Pin Hitch Double Pin Hitch Double Pin Hitch Double Pin Hitch Double Pin Hitch Double Pin Hitch Double Pin Hitch Double Pin Hitch Double Pin Hitch Double Pin Hitch
Required Oil Folw ℓ/Min 150 180 200 Cradie Hitch Cradie Hitch Cradie Hitch Cradie Hitch Cradie Hitch Cradie Hitch Cradie Hitch Cradie Hitch Cradie Hitch Cradie Hitch Cradie Hitch Cradie Hitch Cradie Hitch Cradie Hitch Cradie Hitch

Bucket Loading Opening mm 700 × 500 900 × 500 1,200 × 500 Auger Series mm S4 S4 S4 S4 S4 S5 S5 S5 S5 S5 S6 S6 S6 S6 S6
Operating Weight kg 2,600 3,600 4,500 Auger Length mm 1200 1200 1200 1200 1200 1500 1500 1500 1500 1500 1750 1750 1750 1750 1750
Crusher Output Adjustment mm 20~120 20~120 20~120 Auger dia. Range mm 100~400 100~500 100~600 100~750 100~900 150~600 150~750 150~900 150~900 150~900 150~900 150~900 150~1200 150~1200 150~1200
※ The above specifications are subject to change without prior notice for quality improvement. ※ The above specifications are subject to change without prior notice for quality improvement.
ORANGE GRAPPLE CLAM SHELL

>>>Feature >>>Feature
•Bulk scrap metal, and phage up get off work •Grain transport and up/get off work
•Industry, environmental •Dirt digging sand dredging
waste up get off work •Industrial waste disposal
•Crane hoists can be installed
•One Cylinder and two
A-Type B-Type Cylinders.(tow types)

A-Type B-Type

Tine-Type
Tine of the inner plate

appearance separated

Top-Type
(PENDULUM-TYPE) (LINK-TYPE)

Open Type Half-enclose Type Enclose Type

A-Type Unit HOG 600 HOG 800 HOG 1000 HOG 1500
Capacity LT 600 800 1000 1500
Weight kg 1200 1560 1800 2200
Min mm 928 961 1198 1376
Max mm 1774 1945 2178 2513
H mm 1535 1647 1863 2081
H1 mm 1304 1392 1600 1793
Carrier ton 12~18 18~25 28~35 36~42
※ The above specifications are subject to change without prior notice for quality improvement.

B-Type Unit HOG 600 HOG 800 HOG 1000 HOG 1500 HOG 2000
Capacity LT 600 800 1000 1500 2000
Weight kg 1050 1300 1500 1800 2100
Min mm 849 969 1192 1315 1705
Max mm 1859 1939 2013 2403 2699
H mm 1850 1970 2203 2381 2939
H1 mm 1550 1674 1969 2107 2673
Carrier ton 12~18 18~25 28~35 36~42 43~47
 H
QUICK COUPLER COMPACTOR / SCREENER

1
W
L
W1

Pull Type Compactor

H
W2
B

•Installation Steps

▶
▶

Description Unit HQC 03L HQC 06L HQC 08L HQC 10L HQC 14L HQC 17L HQC 20L
Applicable Carrier ton 5~6 11~13 18~22 23~30 31~36 37~42 43~50
All-in-one block oil flow Proper high-quality oil pressure
L mm 510~585 824 970 1076~1094 1057~1072 1208~1238 1253~1285
control valve motor to all types of models
H mm 293 391 491 552~557 587~610 613~627 628~662
H1 mm 179 243 302 340 355~371 365~383 380~401 Applicable Compacting Flow Rate Pressure Max. Pressure L×W×T Weight
Model Carrier(ton) Force (ton) Vib. (npm) (cc/rev) (bar) (bar) (mm) H (mm) Rubber pad (kg)
W mm 259~269 408~423 477~496 535~584 586~624 624~664 661~726
W1 mm 155~170 260~275 306~334 351~411 385~432 401~443 431~473 HC 03 4~6 4.5 600~3000 30 100~150 180 915 × 530 × 25 745 4 380

W2 153~168 257~273 303~329 347~407 382~429 429~438 429~468 HC 06 9~13 7 600~2000 63 150~200 250 1145 × 700 × 28 850 4 650
mm
B mm 255~290 375~400 450~480 487~540 510~580 533~600 556~612 HC 08 18~22 15 600~2000 80 150~210 250 1250 × 850 × 30 975 4 950

Weight kg 60~70 170~190 330~340 510~528 630~636 670~755 760~890 HC 10 28~32 15 600~2000 80/90 150~210 250 1350 × 950 × 32 1050 6 1150
※ The above specifications are subject to change without prior notice for quality improvement.
Operating Pressure bar 40~350
Flow Rate lpm 10~30
※ The above specifications are subject to change without prior notice for quality improvement.

Description Unit HQC 03H HQC 06H Screener

Push Type Applicable Carrier ton 5~6 11~13 >>>Feature
L mm 575~600 815
•Scrap materials
H mm 286 306
•Waste materials
H1 mm 178.5 230
•Debris in beaches
W mm 259~269 408~423
mm
•Demolition materials
B 45 50
Weight kg 55~70 170~190
•Pebbles in waterways
Operating Pressure bar 40~320
•Excavation filling materials
Flow Rate 10~20
•Materials from the reclamation of rocky soil
lpm
※ The above specifications are subject to change without prior notice for quality improvement.

Model Carrier (ton) Length (mm) Width (mm) Height (mm)

>>>Double Safe Type
W L
HSN 03 3~5 1070 700 805
HSN 04 5~8 1175 800 930
HSN 05 9~12 1480 900 1055
HSN 06 13~16 1950 1200 1460
H
H1

HSN 08 17~21 2190 1400 1650

HSN 10 22~30 2250 1600 1890
Lock bucket 2 pins HSN 17 31~40 2600 1750 2000
※ The above specifications are subject to change without prior notice for quality improvement.
GRAPPLE VIBRATING BUCKET / MULTI GRAPPLE / BUCKET

Fixed Stone Grapple Vibrating Bucket (Vibrating Screener)

>>>Feature
•Handling of seawalls, stones and many others are all available.
•Multipurpose function to prevent slipping
•Available to work with many kinds of stone (Option)
•Available to classify soil cement and stone (Option) B

Applicable Weight Max Pressure Oil Supply

A (mm) B (mm) C (mm) L (mm) Oil Pressure (kg/cm2) Bucket Volumn (m3)
Model Carrier(ton) (kg) (kg/cm 2) LPM (l/min)
A C

HFS 02 3 300 893 107 818 154 110~130 180 20~50 0.028
HFS 03 4~6 430 1,153 164 1,183 305 110~150 180 30~60 0.09 Applicable Operating Internal Hole
Model Carrier(ton) Weight (kg) A (mm) B (mm) C (mm) pressure (bar) width (mm) size (mm)
HFS 04 6~8 600 1,340 172 1,380 408 110~160 180 30~60 0.17
HFS 06 8~13 636 1,545 220 1,550 730 150~170 190 90~120 0.33 HVB 06 12~16 1500 1300 1210 1450 180~200 1100 100×100
HFS 08 18~22 802 1,938 309 2,220 1,430 160~200 210 100~150 0.65 HVB 08 18~26 1700 1300 1400 1620 180~200 1100 100×100
HFS 10 28~32 833 2,060 320 2,235 1,860 160~210 220 130~200 0.7 HVB 10 28~36 1940 1450 1530 1670 180~200 1330 100×100
HFS 14 33~39 944 2,270 422 2,520 2,500 180~210 230 170~250 0.89 ※ The above specifications are subject to change without prior notice for quality improvement.

HFS 20 45~50 964 2,528 470 2,627 3,110 180~220 250 200~300 1.01
※ The above specifications are subject to change without prior notice for quality improvement. Multi Grapple (Folding Thumb)

B
W

H
Rotating Stone Grapple H
1 >>>Feature
L W
A

•Waste treatment in the wrecking place

•Carrying rocks and excellent performance in loading •Smash for wooden building
•Strong power and a crash-cushion on high pressure cylinder H
B

•Working substance treatment for recycling

•Excellent abrasion resistance and high gradient prolong its life
•Landscaping and stone work
•Swing bearing shock absorber A

•The safety check valve in cylinder prevents the grabbed material from falling down.

Applicable A B W H H1 Weight Cylinder Oil Cylinder Setting Flow Hyd. Max Torque Max Inlet Max Max Flow
Model
Carrier(ton) (mm) (mm) (mm) (mm) (mm) (kg) Pressure (cm )
2
Pressure(kg/㎠) Rate (l/min) Motor (daNm) Pressure (bar) Speed (rpm) Rate (l/min)
HRS 03 4~6 1,280 100 430 1,360 1,190 365 110~200 250 30~50 225 240 75
Applicable Operating
MR315CU 61 Model Weight (kg) A (mm) B (mm) R (mm) L (mm) W (mm) H (mm)
Carrier(ton) Pressure (bar)
HRS 06 9~13 1,700 120 507 1,625 1,400 850 150~220 250 90~120 MT500 160 300 285 150
HMG 03 4~6 97 823 526 997 1,255 235 353 110~140
HRS 08 18~22 2,100 250 620 2,045 1,740 1,960 160~240 260 100~150 MT500 160 300 285 150
HMG 06 9~13 175 1,235 676 1,368 1,604 264 409 150~170
HRS 10 28~32 2,345 268 665 2,210 1,870 2,100 160~240 260 130~200 MT500 160 300 285 150
※ The above specifications are subject to change without prior notice for quality improvement.
※ The above specifications are subject to change without prior notice for quality improvement.

Bucket
W

Rotating Wood Grapple

•Outstanding performance on loading at the logging place
•High use in various works
H H1

•During the swing work, it prevents the grabbed material from falling B

down by grabbing more safely even when the machine is stopped

Applicable A B W H H1 Weight Cylinder Oil Cylinder Setting Flow Hyd. Max Torque Max Inlet Max Max Flow
Model Carrier(ton) (mm) (mm) (mm) (mm) (mm) (kg) Pressure (cm )
2
Pressure(kg/㎠) Rate (l/min) Motor (daNm) Pressure (bar) Speed (rpm) Rate (l/min)
HRW 03 4~6 1,280 100 430 1,360 1,190 365 110~200 250 30~50 MR315CU 61 225 240 75
HRW 06 9~13 1,700 120 507 1,625 1,400 850 150~220 250 90~120 MT500 160 300 285 150
HRW 08 18~22 2,100 250 620 2,045 1,740 1,960 160~240 260 100~150 MT500 160 300 285 150
HRW 10 28~32 2,345 268 665 2,210 1,870 2,100 160~240 260 130~200 MT500 160 300 285 150
※ The above specifications are subject to change without prior notice for quality improvement.
RIPPER / DOUBLE & MULTI RIPPER / LIFTING FORK PEDESTAL BOOM BREAKER