CT10 HL

Download as pdf or txt
Download as pdf or txt
You are on page 1of 4

इ रर से ट IRISET

ननयांञण प्रयोगशाला CONTROL LABORATORY


प्रयोग सां: सी टी 10 EXPERIMENT NO: CT-10

नाम
Name : _______________
अनक्र
ु माांक प्राप्त अांक
Roll No : _______________ Marks Awarded:
पाठ्यक्रम
Course : _______________
दिनाांक अनिु े शक का आधाक्षर
Date : _______________ Instructor Initial:

T
EXPERIMENT No. CT -10

Introduction
EConfiguration of Gf400 System

After installation of Gf400 system all its units except TWA are needed to be configured
IS
(programmed) first by selecting different parameter values before using the system for control
communication. The individual units in the system are using circuitry based on 8051
microcontroller. Let us see how to configure each unit of the system.

SYSTEM CONFIGURATION
IR

1. Way Station Equipment (MTWE) Configuration


Following is the procedure for configuring the way station equipment, MTWE.

Procedure:
1. Switch off power to MTWE by power switch.
2. Insert a thin screw driver or rod into the small hole -Prog- provided above the display,
keep the Program button inside the hole pressed and then switch on power.
3. Letters PrG appear on the display. Now it is possible to configure MTWE for all its
parameters settings as well as to view existing settings.
4. For this purpose the 1st control telephone connected to ST1 line on MTWE can only be
used.
5. Pressing digits on ST1 Control Telephone keypad in the sequence shown in the Table
2.1, way station equipment parameters can be either viewed or set.

1 Control Lab-IRISET- CT-10


a) View or Set MTWE Parameters
SNo To View or Set Digits to be dialed from ST1 Options
Telephone
To View (start with 5, 2) 1st 4-bits
only
To Set ( start with 5, 1) 6-bits
1 Tx gain 5 2/1 0 1 0 0/1/2 Low / Normal / High
2 Rx gain 5 2/1 0 2 0 0/1/2 Low / Normal / High
3 DTMF Tx gain 5 2/1 0 3 0 0/1/2 Low / Normal / High
4 DTMF Rx gain 5 2/1 0 4 0 0/1/2 Low / Normal / High
5 Load Default 5 2/1 0 5 0 0 Sets Normal gain, 4 min
Settings* timeout, no dialing, etc.
6 Handset Timeout 5 2/1 1/2/3/4 0 0 1/2/3 4 min/ 8 min / infinite

T
7 Way station 5 2/1 1/2/3/4 1 0-9 0-9 1/2/3/4 to represent ST1- 4
Telephone Number 0-9 to enter telephone no.
8 Way station Group E 5 2/1 1/2/3/4 2 0 1-9 1/2/3/4 to represent ST1- 4
Code 1-9 to enter Group Code no.
9 Ring Pattern 5 2/1 1/2/3/4 3 0 1-4 1-4 for ring pattern
IS
10 Ring Duration 5 2/1 1/2/3/4 4 0 0-9 Duration can be set 10-225s
11 Dialing Permission 5 2/1 1/2/3/4 5 0 0/1/2 To dial: Nil / 4/ All phones
Table-2.1
IR

*Default Settings for Way Station Equipment


The following table shows the default settings that are loaded to way station equipment when it
is programmed with ‘Load default Settings’ option.

SNo Parameter Default Setting Default Value


Loaded
1 All Tx & Rx gains 1 Normal Gain (0dB)
ST1 ST2 ST3 ST4
5 Handset Timeout 1 1 1 1 4 Minute Duration
6 Way station Telephone Number 12 13 14 15 WS codes- 12,13,14 & 15
7 Way station Group Code 1 1 1 1 group code -11 for all 4
8 Ring Pattern 1 2 3 4 4 different ring sounds
9 Ring Duration 0 0 0 0 10 sec
10 Dialing Permission 0 0 0 0 No dialing facility
Table-2.2

2 Control Lab-IRISET- CT-10


Exercise-1:
1. Assign telephone numbers C31 and D71 to control telephones connected to ST1 and
ST2 of first MTWE.
2. Call these numbers from TRE. Record your observation.

2. CRE- Control Room Equipment Configuration


This process involves assigning way station codes to each of 40 keys on CRE front panel
using the following procedure.
Procedure:
1) Switch off CRE by Turning Off its power switch.
2) Press and hold PROGRAM button and then Turn On Power to CRE again.

T
3) Letters ‘ PrG’ appear on the display indicating the Program mode of CRE
4) Release PROGRAM push button.
E
5) With Mic button, select C for DTMF type code
(NOTE: Type of codes possible: C-Classic means DTMF; d- DASSFO; CG- DTMF group
IS
code; dG- DASSFO group code)

6) Next select code 31 by pressing numeral keys.


7) Then press PROGRAM push button.
8) Three beeps are heard. Before the beeps stop, press the first key of the 40 keys.
IR

9) A long beep is heard indicating successful programming of the key.


10) By this process, the way station code 31 is assigned to 1st key of 40 keys.
11) Now using Mic button select d for DASSFO type code.
12) Then enter code 71 using numeral keys.
13) Press in sequence, keys Program, Shift and then the same 1st key of the 40 keys.
14) With this way station codes C31 and D71 are assigned to the first key.

(NOTE: Each key of 40 keys can be programmed for any two types of codes only)

15) Switch off CRE and then switch it on without pressing Program button.
16) Now press 1st key and observe code on the display; it should be C.31.
17) Press Shift then 1st key and observe on the display; it should be d.71
18) Like this each of the 40 buttons can be programmed for two different way station codes.

3 Control Lab-IRISET- CT-10


Exercise-2:
1. Using the 1st button on CRE keypad call telephone numbers C31 and D71 and
observe whether the way station phones ring. Record your observation.

3. TRE- Test Room Equipment Configuration


Unlike CRE and MTWE, there is no separate programming mode for TRE. Instead, it can
be used in normal working mode itself to view, as well as to set configuration of different line
interfaces and parameters. These are - Line make or break, adjust- Tx & Rx level and
Ring Duration, Switch RPEs, Read or Load CRE configuration etc.

Procedure:

T
To carry out the above mentioned functions, follow the menu sequences shown below
through TRE keypad.

1.   SETTING 
E
TOOLS  VIEW 
LINE A
LINE B
DTMF DASSFO



DEC
LT
HS



■ Indicates ‘’ Line is “Through”
IS
EDIT
DTMF CLASSIC ■ LS ■ □ Indicates “Line is “Cut”

a) LINE A (LINE B/ DEC / LT/ CLASSIC / DASSFO )


2.  VIEW
 SETTING  TOOLS  EDIT  LINE A  Tx LEVEL
IR

Rx LEVEL

b) LINE A (LINE B / DEC / LT/ CLASSIC / DASSFO/ HS / LS)

MAKE MAKE
3.   SETTING  REMOTE
OPERATION
 BREAK BREAK
STATUS
c) RING DURATION
d) DEC SETTINGS - READ /LOAD DEC

Exercise-3:
1. Verify present status of different line interfaces on TRE and record it below.
2. Verify and mention what are the other functions that can be performed from TRE.
3. Read the present status of RPE and switch it to Through state. Call way stations in the
path connected through RPE. Also try to call them keeping RPE in Cut state.

4 Control Lab-IRISET- CT-10

You might also like