LED VU Meter circuits using transistors, 5

to 20, 40 LED
If you like the transistor amplifier. You may also like a VU meter using the
transistor. They are one type of LED VU meter circuits.

Also, It works with an integrated amplifier circuit. To show a level of the

sound signal or rhythm of the music by the LED flash lighting.

Why should use transistors version

You may have a question. Is it better than IC? I cannot tell you. It is the
best VU meter. But I can show you the transistor is so great all the time.

● Easy to get them—Although they are quite ancient. But it is still

always popular.
 2

For example:
2SC458 transistor, now The factory quit producing it. But we can
use other transistors instead like 2SC828, 2SC945, 2SC1815,
etc.

● Cheap—They are inexpensive when compare with IC. Although

we need to use a lot of transistors. If it breaks out. You can fix it
one by one, do not change it all.

It is different from the IC. You need to change IC only.

● Simple circuit—suitable for learning basic electronics

5 LED VU Meter Circuit

Look at the circuit. Here is a simple VU meter. It has only the necessary
parts.

When entering the power supply to the circuit. Then, connects an input of
the VU meter to the output of the amplifier.
 3

Next, four diodes D1, D2, D3, and D4 pass the input audio signal. They
have 2 functions.

● First, rectify the audio signal, AC voltage to DC voltage.

● Second, divide the audio signal to gradually decrease,

respectively.

To forward to each the transistors Q1-Q4 through Resistors, R5-R8.

They limited bias current to the base of Q1-Q4 to increase current up to
each collector.
 4

To drive LED1-LED4, to show the level of the signal. The LED1 displays
an audio level with the least light. And the LED4 shows the most level
signals.

I think you may not understand I said. Back…reading.

Each diode has a voltage across is 0.6V. Suppose the signal is 1.8V.

It causes the current can flow to three diodes, D1, D2, D3, So,
LED1-LED3 glow up. But LED4 and LED5 will go out.

Note: likewise you can see the second circuit that using more LEDs, too.

25 LEDs VU meter Circuit (Increase LED)

The weakness of the previous circuit is cannot display low voltage. So,
we need to improve it.

In the circuit below. It has a voltage doubler circuit, C1, C2, R1, R2.

They approximately double an incoming AC voltage. Also, the output is

DC voltage.
 5

Adding LEDs for 25 LEDs Analog VU Meter circuit using transistors

Make the audio signal into more voltage. So, all transistors can drive all
LEDs to emit light much more.

How it works

First of all, when applying the power supply to the circuit. And VR1
passed the input signal and adjust the sound more or less.
 6

Then, flows through the C1 signal coupling.

Next, the signal goes into the circuit to increase the voltage with D1 and
D2. Which both diodes rectifier AC to DC with positive and negative
together.

After that, DC voltage comes to C2 to filters into a smooth DC voltage.

The first part of the signal will flow through R1 to the base of Q1. It works
to drive LED1-LED5 to light up.

The remaining signal is sent through diodes D3, D4 and D5. This will
serve to break the sound signal to gradually decrease, respectively.

To forward to the transistors Q2-Q4, each level of the signal strength

coming.

Then expand to the LED current to light the rhythm music.

Not only that see improved circuits with PCB layout.

20 to 40 LED VU meter schematic

This is 20 LED VU meter schematic is designed for who want to have a

circuit that can drive LED up to 20 pcs (Stereo 40 LEDs). Which the
circuit using a generally IC will cannot directly connect to uses.

In addition to this project is very easily circuit and also can modify to
drives Solid State Relay for easily control a larger lamp.

As you see the complete circuit of the projects in Figure 1.

 7

The working of this circuit

An input signal from the power amplifier is passed through to VR1, to

adjust the amplitude of this input signal at the proper level.

Then, the signal is sent to the voltage doubler rectifier circuit. That
consists of C1, C2, D1, D2 to the circuit. And all transistors Q1-Q10 that
together into the voltage compare circuit.

20 (40) LED VU meter using transistor circuit

We can see the bass circuits of each transistor will be set a bias with
D3-D40. To provide to have a voltage bias is different for every 2 volts,
respectively.

So, transistor Q1 will start work at a lower signal and Q20 will work on
the strongest signal.

The section of the circuit is in the dash as the shortening of the circuit is
repeated. They consisting of Q4-Q18.
 8

How to build

We Assembly the circuit onto the PCB layout as Figure 2 correctly.

So, must be extra careful is. Devices with terminals such as Diode,
Electrolytic capacitors, and LED will are connected right terminals only.

See the PCB layout and the components layout of the 20 LED cheap
electronic VU-meter using transistor project.

PCB layout #1

[pcb-layout1-20-led-vu-meter-transistor.jpg]

PCB layout #2
 9

[pcb-layout2-20-led-vu-meter-transistor.jpg]

Component layout #1

Component layout #2

When the assembly is completed. Then, test to provide the voltage

power supply to this project. While connects the input signal from a
speaker of a power amplifier.
 10

Next, turn on it at the highest audio. Then adjust VR1 to LED glow fully
all LED. Now already have fun.

The components List

Q1-Q20: 2SC458, 2SC828,C945,C1815, 45V 0.1A, NPN Transistor

D1-D40: 1N4148, 75V 0.15A Diodes

R1-R20: 15K, Resistors 0.25W +/- 5%

R21-R40: 500 ohms, Resistors 0.25W +/- 5%

VR1: 10K, potentiometer POT

C1: 33uF 50V, Electrolytic

C2: 3.3uF 50V, Electrolytic

LED1-LED20: LED 2 x 5 mm.

Note:

For friends who cannot buy C458 or C1815 transistor. You can use
2N3904 instead. But you need to swap the legs B-C. Be careful with pins
B-C short-circuited. You may be able to use insulator on pin B.
 11

I hope you will enjoy this project. We love transistor circuits. so gradually
assembling them. I believe you can.