EMI EMC TRAINING LAB EMI04

Laptop not included

Features Scope of Experimentation
*Pre- Compliance testing 1. Introduction Helmholtz Coil
*Effectiveness of a shielding material 2. TEM Field generator
* Location source of emissions of pcb tracks 3. LISN
*Effectiveness of a Ferrite as a HF suppressor 4. Probes Set Near field E/H
*Measuring induction into conductors 5. LF Electromagnetic Detector
*Tracking currents on a conducting plane 6. Electrical Fast transient generator
*Estimating cross talk on PCB 7. EMC Analyser
Software Features 8. EM Demo Kit
*Numerous pre-configured project files for CISPR-xx (EN550xx) 9. Software
emission measurements 10. Emissions reference Source
*Graph supports two complete measurement runs, same as in 11. Tips for Electronic Printed Circuit Board Design
test house 12. Measurement techniques and test methods
*Fast Quasi-Peak scan of critical peaks, immune to *frequency 13. To measure the effectiveness of shielding material.
drift of the selected peaks 14. To locate the source of emissions of a PCB track.
*Configurable limit lines and segment files 15. To demonstrate the use of ferrite as HF suppressor.
*Configurable correction files for cable, LISN, amplifier, antenna 16. To measure the induction into conductors.
etc. 17. To analyse tracking of currents on a conducting plane.
*Configurable margins for the identification and selection of 18. To estimate the cross talk on adjacent tracks in a PCB.
critical peaks 19. To analyse the use of Helmholtz coil for testing magnetic
*Supports import and overlaying of reference *measurements for susceptibility.
comparison purpose 20. To analyse the use of TEM field generator for testing
*Linear or logarithmic frequency axis radiated electric susceptibility of DUT
*automatic creation of test reports 21. To analyse the use of LISN for testing conducted
*Selective measurement of frequency segments emissions of DUT
*RF-coverage measurement mode 22. Use of a preamp to increase the sensitivity of CRO.
23. Use of an EMC analyzer with antennas for RE testing

Disclaimer: Images shown are Indicative only. Color or Model may differ from the picture shown (Features will remain same or More). Specifications are subject to change without notice.
Mfd by: Amitec Electronics Ltd.
Regd. Off: 504, Nilgiri, 9 Barakhamba Road, New Delhi-110001, India, Works: 4/32, Site-4, Industrial Estate Sahibabad, NCR-201010, India,
[email protected], www.amitec.co
+91-11-41505510, +91-120-4371276
 EMI EMC TRAINING LAB EMI04

1. Near Field Magnetic probe M1 6. Wideband Amplifier

Type: Loop Frequency Range: 9KHz-
Sensor: Magnetic Field 4GHz
Rejection E/H: 40dB Noise figure: 3dB
Frequency: 800MHz upper Gain: 40dB
resonant Compression 1dB: 10dBm
Sensitivity: High
Diameter: 6cm

2. Near Field Magnetic probe M2 7. Emissions Reference Source1

Type: Loop Frequency: 10-4000 MHz
Sensor: Magnetic Field Harmonic Spacing: 10 MHz
Rejection E/H: 30dB /50 MHz
Frequency: 1.5GHz upper Frequency Stability: 100ppm
resonant Impedance: 50 Ohms
Sensitivity: High RF level at 3m: 40-80
Diameter: 3cm dBuV/m
Radiant Field polarisation:
Vertical and Horizontal

3. Near Field Magnetic probe M3 8. Emissions Reference Source2

Type: Loop Frequency: DC-4000 MHz
Sensor: Magnetic Field Harmonic Spacing: 0
Rejection E/H: 10dB (Noise)
Frequency: 2.5GHz upper Impedance: 50 Ohms
resonant RF level at 3m :30-50
Sensitivity: Low dBuV/m
Diameter: 1cm Radiant Field polarisation:
Vertical and Horizontal

4. Near Field Electric probe E1 9. EMC Analyser cum Spectrum Analyser

Type: Omni Directinoal Frequency: 9KHz-1500MHz
Sensor: Electric Field RBW: 100Hz Min
Rejection H/E: 30dB Phase Noise: -80dBc/Hz at
Frequency: 1GHz upper 10KHz
resonant Sensitivity: -135dBm
Sensitivity: High Input Impedance: 50 Ohms
Diameter: 3.6cm Tracking Output:0dBm
Not Provided

5. Near Field Electric probe E2 10.Reference Logperiodic

Type: Narrow Directinoal S11: >10dB
Sensor: Electric Field Bandwidth: 1 to 6GHz
Rejection H/E: 30dB Gain: 4dBi
Frequency: 3GHz upper Beamwidth : E plane 600
resonant Beamwidth : H Plane 1800
Sensitivity: Low Polarisation : Linear
Size: 0.6cm Front to Back Ratio: 10dB
Connector : SMA

Disclaimer: Images shown are Indicative only. Color or Model may differ from the picture shown (Features will remain same or More).
Specifications are subject to change without notice due to continuous improvement of product.

Disclaimer: Images shown are Indicative only. Color or Model may differ from the picture shown (Features will remain same or More). Specifications are subject to change without notice.
Mfd by: Amitec Electronics Ltd.
Regd. Off: 504, Nilgiri, 9 Barakhamba Road, New Delhi-110001, India, Works: 4/32, Site-4, Industrial Estate Sahibabad, NCR-201010, India,
[email protected], www.amitec.co
+91-11-41505510, +91-120-4371276
 EMI EMC TRAINING LAB EMI04

11. Ferrite Suppressors 16. Antenna Magnetic Loop

Ferrite suppressor, Feed- Frequency: 9KHz-30MHz
through Capacitors Diameter : 300mm
EM Suppression : 40dB Connector : SMA
Inductance: 1uH
Turns: Multi

12. LF/HF Electromagnetic Detector 17. Helmholtz Coil

Measuring range: -60dBm to - Type: Mono-axial
5dBm Resistance: 0.5 Ohms DC
Resolution: 0.1dB Inductance: 3.5mH
Frequency Range: 9KHz- Amperes/m/Ampere:84.3
4GHz Coil Factor : 1Gauss/A
Accuracy: 3dB Homogeneity: +10% within
Input: SMA a 15cm cylinder
Impedance: 50 Ohms Self resonance: 32 KHz
Input SWR: <2 Maximum Current: 20A
Output: 500mV/10dB Maximum Field: 21.2Gauss
Mating Connector: Terminal
Size Diameter: 305mm
13. EM Demo Kit 18. LISN- Line Impedance Stabilization Network
SMPS, EM demo board, Frequency: 9kHz - 30 MHz
Ferrite Suppressors, Shielded (VDE 0876 specified curve
Cans +/-20%)FCC-15 VDE 0871
VDE 0876 EN55022
Network: 50uH / 250 uH
Network impedance: 50ohm
Current rating: 1 amps
Max. AC: 250 VAC 50 Hz
Outlet: British BS546
Input connector: IEC-320
type 3-wire inlet.
Safe:Transient Suppressor
14. Antenna 19. TEM Field Generator
S11: >10dB Type: Tri-plate Stripline
Bandwidth: 600 + 300 MHz Frequency :10KHz-1GHz
Gain: 2dBi S12: <3dB
Beamwidth : E plane 600 E-field : 90V/m at 10W
Beamwidth : H Plane 1800 Impedance : 50 Ohms
Polarisation : Linear Connector: Type N Female
Front to Back Ratio: 0dB Dimensions length: 600mm
Connector : SMA approx
Width: 300mm approx
Height: 300mm approx

15. Shielded Tent 20. Software

Outer dim:120x60x60 cm It is an EMC pre-compliance
Opening dim: 85 x35 cm testing of radiated and
Shielding: 2 layers of conducted emissions. A built
conductive fabrics in amplitude correction
Filter panel: 1 x240V/10A AC enables correction and
filter; IEC socket;2 x240V/10A conversion coefficients for
DC filter; cables with female cables, amplifiers,
Banana couplers; 3 x N- attenuators, LISNs, TEM
female feed through cells, antennas, RF current
connector with screw caps; 1 probes, striplines and
x BNC-female feed through capacitive coupling clamps.
connector;Attenuation: >58 dB
in the range DC to 1.5 GHz

Disclaimer: Images shown are Indicative only. Color or Model may differ from the picture shown (Features will remain same or More). Specifications are subject to change without notice.
Mfd by: Amitec Electronics Ltd.
Regd. Off: 504, Nilgiri, 9 Barakhamba Road, New Delhi-110001, India, Works: 4/32, Site-4, Industrial Estate Sahibabad, NCR-201010, India,
[email protected], www.amitec.co
+91-11-41505510, +91-120-4371276
 EMI EMC TRAINING LAB EMI04

21. Comb Generator/Frequency Multiplier 23. Transient Limiter

It is a passive, step recovery It is a combined transient
diode based comb generator / limiter / attenuator / high pass
frequency multiplier. It is filter, designed to provide
optimized for moderate drive optimum protection of
power and spectrum flatness spectrum analyzer or
in the frequency range 1 MHz measurement receiver inputs
to 2.5GHz. when carrying out conducted
Drive power is +10 dBm to noise measurements or other
+20 dBm measurements where the
The frequency range for the input levels cannot be
drive signal is 1 MHz to predicted with certainty or
350MHz where accidental overloads
Input Power: +10 dBm to +20 may occur.
dBm; 25 dBm max Freq range: 9 kHz – 600 MHz
Input Frequency: 1 MHz to Attenuation: 10 dB – 0.5/+1.2
350 MHz dB in-band (9 kHz to 600
Comb spectrum: 1 MHz - 2.5 MHz)
GHz Attenuation HP-filter: > 30 dB
Input connector: N female @ 2kHz
Output connector: N m Maximum continuous RF input
power: 5W (+37 dBm) in-band
Max DC input voltage: ± 20V
Input matching, linear
operating range: 9 kHz – 600
MHz < – 16 dB
Output matching, linear
operating range: 9 kHz – 600
MHz < – 23 dB
Linear operating range: up to
0 dBm input level, in-band
Limiting threshold: +11 dBm
(@ 37dBm input level)
22. Radiating Comb Generator
It is a radiating comb
generator with an internal
antenna and a base frequency
of 100MHz. It radiates a comb
spectrum characterized up to
6GHz. The comb generator is
built and characterized to
serve as a rough reference for
testing radiated noise
measurement set ups in
anechoic chambers,
TEM/GTEM cells, shielded
chambers, etc.
It is a portable device,
powered by a 9V cell.
Base frequency: 100 MHz
Characterized comb spectrum:
30 MHz - 6 GHz
Power supply: 9V PP3 (E-
block) alkaline battery
Current consumption:175 mA

Disclaimer: Images shown are Indicative only. Color or Model may differ from the picture shown (Features will remain same or More).
Specifications are subject to change without notice due to continuous improvement of product.
Disclaimer: Images shown are Indicative only. Color or Model may differ from the picture shown (Features will remain same or More). Specifications are subject to change without notice.
Mfd by: Amitec Electronics Ltd.
Regd. Off: 504, Nilgiri, 9 Barakhamba Road, New Delhi-110001, India, Works: 4/32, Site-4, Industrial Estate Sahibabad, NCR-201010, India,
[email protected], www.amitec.co
+91-11-41505510, +91-120-4371276